/*USB 1.1,2.0 device*/ #include <common.h> #include <asm/processor.h> #if (defined(CONFIG_440EP) || defined(CONFIG_440EPX)) && defined(CONFIG_CMD_USB) #include <usb.h> #include <asm/ppc4xx-uic.h> #include "usbdev.h" #define USB_DT_DEVICE 0x01 #define USB_DT_CONFIG 0x02 #define USB_DT_STRING 0x03 #define USB_DT_INTERFACE 0x04 #define USB_DT_ENDPOINT 0x05 int set_value = -1; void process_endpoints(unsigned short usb2d0_intrin) { /*will hold the packet received */ struct usb_device_descriptor usb_device_packet; struct usb_config_descriptor usb_config_packet; struct usb_string_descriptor usb_string_packet; struct devrequest setup_packet; unsigned int *setup_packet_pt; unsigned char *packet_pt = NULL; int temp, temp1; int i; /*printf("{USB device} - endpoint 0x%X \n", usb2d0_intrin); */ /*set usb address, seems to not work unless it is done in the next interrupt, so that is why it is done this way */ if (set_value != -1) *(unsigned char *)USB2D0_FADDR_8 = (unsigned char)set_value; /*endpoint 1 */ if (usb2d0_intrin & 0x01) { setup_packet_pt = (unsigned int *)&setup_packet; /*copy packet */ setup_packet_pt[0] = *(unsigned int *)USB2D0_FIFO_0; setup_packet_pt[1] = *(unsigned int *)USB2D0_FIFO_0; temp = *(unsigned int *)USB2D0_FIFO_0; temp1 = *(unsigned int *)USB2D0_FIFO_0; /*do some swapping */ setup_packet.value = swap_16(setup_packet.value); setup_packet.index = swap_16(setup_packet.index); setup_packet.length = swap_16(setup_packet.length); /*clear rx packet */ *(unsigned short *)USB2D0_INCSR0_8 = 0x48; /*printf("0x%X 0x%X 0x%X 0x%X 0x%X 0x%X 0x%X\n", setup_packet.requesttype, setup_packet.request, setup_packet.value, setup_packet.index, setup_packet.length, temp, temp1 ); */ switch (setup_packet.request) { case USB_REQ_GET_DESCRIPTOR: switch (setup_packet.value >> 8) { case USB_DT_DEVICE: /*create packet */ usb_device_packet.bLength = 18; usb_device_packet.bDescriptorType = USB_DT_DEVICE; #ifdef USB_2_0_DEVICE usb_device_packet.bcdUSB = swap_16(0x200); #else usb_device_packet.bcdUSB = swap_16(0x110); #endif usb_device_packet.bDeviceClass = 0xff; usb_device_packet.bDeviceSubClass = 0; usb_device_packet.bDeviceProtocol = 0; usb_device_packet.bMaxPacketSize0 = 32; usb_device_packet.idVendor = swap_16(1); usb_device_packet.idProduct = swap_16(2); usb_device_packet.bcdDevice = swap_16(0x300); usb_device_packet.iManufacturer = 1; usb_device_packet.iProduct = 1; usb_device_packet.iSerialNumber = 1; usb_device_packet.bNumConfigurations = 1; /*put packet in fifo */ packet_pt = (unsigned char *)&usb_device_packet; break; case USB_DT_CONFIG: /*create packet */ usb_config_packet.bLength = 9; usb_config_packet.bDescriptorType = USB_DT_CONFIG; usb_config_packet.wTotalLength = swap_16(25); usb_config_packet.bNumInterfaces = 1; usb_config_packet.bConfigurationValue = 1; usb_config_packet.iConfiguration = 0; usb_config_packet.bmAttributes = 0x40; usb_config_packet.MaxPower = 0; /*put packet in fifo */ packet_pt = (unsigned char *)&usb_config_packet; break; case USB_DT_STRING: /*create packet */ usb_string_packet.bLength = 2; usb_string_packet.bDescriptorType = USB_DT_STRING; usb_string_packet.wData[0] = 0x0094; /*put packet in fifo */ packet_pt = (unsigned char *)&usb_string_packet; break; } /*put packet in fifo */ for (i = 0; i < (setup_packet.length); i++) { *(unsigned char *)USB2D0_FIFO_0 = packet_pt[i]; } /*give tx command */ *(unsigned short *)USB2D0_INCSR0_8 = 0x0a; break; case USB_REQ_SET_ADDRESS: /*copy usb address */ set_value = setup_packet.value; break; } } } void process_other(unsigned char usb2d0_intrusb) { /*check for sof */ if (usb2d0_intrusb & 0x08) { /*printf("{USB device} - sof detected\n"); */ } /*check for reset */ if (usb2d0_intrusb & 0x04) { /*printf("{USB device} - reset detected\n"); */ /*copy usb address of zero, need to do this when usb reset */ set_value = 0; } if (usb2d0_intrusb & 0x02) { /*printf("{USB device} - resume detected\n"); */ } if (usb2d0_intrusb & 0x01) { /*printf("{USB device} - suspend detected\n"); */ } } int usbInt(void) { /*Must read these 2 registers and use values to clear interrupts. If you do not read them then the interrupt will not be cleared. If you do not use the variable the optimizer will not do a read. */ volatile unsigned short usb2d0_intrin = *(unsigned short *)USB2D0_INTRIN_16; volatile unsigned char usb2d0_intrusb = *(unsigned char *)USB2D0_INTRUSB_8; /*check if there was an endpoint interrupt */ if (usb2d0_intrin != 0) { process_endpoints(usb2d0_intrin); } /*check for other interrupts */ if (usb2d0_intrusb != 0) { process_other(usb2d0_intrusb); } return 0; } #if defined(CONFIG_440EPX) void usb_dev_init() { printf("USB 2.0 Device init\n"); /*usb dev init */ *(unsigned char *)USB2D0_POWER_8 = 0xa1; /* 2.0 */ /*enable interrupts */ *(unsigned char *)USB2D0_INTRUSBE_8 = 0x0f; irq_install_handler(VECNUM_USBDEV, (interrupt_handler_t *) usbInt, NULL); } #else void usb_dev_init() { #ifdef USB_2_0_DEVICE printf("USB 2.0 Device init\n"); /*select 2.0 device */ mtsdr(sdr_usb0, 0x0); /* 2.0 */ /*usb dev init */ *(unsigned char *)USB2D0_POWER_8 = 0xa1; /* 2.0 */ #else printf("USB 1.1 Device init\n"); /*select 1.1 device */ mtsdr(sdr_usb0, 0x2); /* 1.1 */ /*usb dev init */ *(unsigned char *)USB2D0_POWER_8 = 0xc0; /* 1.1 */ #endif /*enable interrupts */ *(unsigned char *)USB2D0_INTRUSBE_8 = 0x0f; irq_install_handler(VECNUM_USBDEV, (interrupt_handler_t *) usbInt, NULL); } #endif #endif /* CONFIG_440EP || CONFIG_440EPX */