/* * (C) Copyright 2007 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * based on work by Anne Sophie Harnois <anne-sophie.harnois@nextream.fr> * * (C) Copyright 2001 * Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #include <common.h> #include <ppc4xx.h> #include <4xx_i2c.h> #include <i2c.h> #include <asm-ppc/io.h> #ifdef CONFIG_HARD_I2C DECLARE_GLOBAL_DATA_PTR; #if defined(CONFIG_I2C_MULTI_BUS) /* Initialize the bus pointer to whatever one the SPD EEPROM is on. * Default is bus 0. This is necessary because the DDR initialization * runs from ROM, and we can't switch buses because we can't modify * the global variables. */ #ifndef CONFIG_SYS_SPD_BUS_NUM #define CONFIG_SYS_SPD_BUS_NUM 0 #endif static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = CONFIG_SYS_SPD_BUS_NUM; #endif /* CONFIG_I2C_MULTI_BUS */ static void _i2c_bus_reset(void) { int i; u8 dc; /* Reset status register */ /* write 1 in SCMP and IRQA to clear these fields */ out_8((u8 *)IIC_STS, 0x0A); /* write 1 in IRQP IRQD LA ICT XFRA to clear these fields */ out_8((u8 *)IIC_EXTSTS, 0x8F); /* Place chip in the reset state */ out_8((u8 *)IIC_XTCNTLSS, IIC_XTCNTLSS_SRST); /* Check if bus is free */ dc = in_8((u8 *)IIC_DIRECTCNTL); if (!DIRCTNL_FREE(dc)){ /* Try to set bus free state */ out_8((u8 *)IIC_DIRECTCNTL, IIC_DIRCNTL_SDAC | IIC_DIRCNTL_SCC); /* Wait until we regain bus control */ for (i = 0; i < 100; ++i) { dc = in_8((u8 *)IIC_DIRECTCNTL); if (DIRCTNL_FREE(dc)) break; /* Toggle SCL line */ dc ^= IIC_DIRCNTL_SCC; out_8((u8 *)IIC_DIRECTCNTL, dc); udelay(10); dc ^= IIC_DIRCNTL_SCC; out_8((u8 *)IIC_DIRECTCNTL, dc); } } /* Remove reset */ out_8((u8 *)IIC_XTCNTLSS, 0); } void i2c_init(int speed, int slaveadd) { unsigned long freqOPB; int val, divisor; int bus; #ifdef CONFIG_SYS_I2C_INIT_BOARD /* call board specific i2c bus reset routine before accessing the */ /* environment, which might be in a chip on that bus. For details */ /* about this problem see doc/I2C_Edge_Conditions. */ i2c_init_board(); #endif for (bus = 0; bus < CONFIG_SYS_MAX_I2C_BUS; bus++) { I2C_SET_BUS(bus); /* Handle possible failed I2C state */ /* FIXME: put this into i2c_init_board()? */ _i2c_bus_reset(); /* clear lo master address */ out_8((u8 *)IIC_LMADR, 0); /* clear hi master address */ out_8((u8 *)IIC_HMADR, 0); /* clear lo slave address */ out_8((u8 *)IIC_LSADR, 0); /* clear hi slave address */ out_8((u8 *)IIC_HSADR, 0); /* Clock divide Register */ /* get OPB frequency */ freqOPB = get_OPB_freq(); /* set divisor according to freqOPB */ divisor = (freqOPB - 1) / 10000000; if (divisor == 0) divisor = 1; out_8((u8 *)IIC_CLKDIV, divisor); /* no interrupts */ out_8((u8 *)IIC_INTRMSK, 0); /* clear transfer count */ out_8((u8 *)IIC_XFRCNT, 0); /* clear extended control & stat */ /* write 1 in SRC SRS SWC SWS to clear these fields */ out_8((u8 *)IIC_XTCNTLSS, 0xF0); /* Mode Control Register Flush Slave/Master data buffer */ out_8((u8 *)IIC_MDCNTL, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB); val = in_8((u8 *)IIC_MDCNTL); /* Ignore General Call, slave transfers are ignored, * disable interrupts, exit unknown bus state, enable hold * SCL 100kHz normaly or FastMode for 400kHz and above */ val |= IIC_MDCNTL_EUBS|IIC_MDCNTL_HSCL; if (speed >= 400000) val |= IIC_MDCNTL_FSM; out_8((u8 *)IIC_MDCNTL, val); /* clear control reg */ out_8((u8 *)IIC_CNTL, 0x00); } /* set to SPD bus as default bus upon powerup */ I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM); } /* * This code tries to use the features of the 405GP i2c * controller. It will transfer up to 4 bytes in one pass * on the loop. It only does out_8((u8 *)lbz) to the buffer when it * is possible to do out16(lhz) transfers. * * cmd_type is 0 for write 1 for read. * * addr_len can take any value from 0-255, it is only limited * by the char, we could make it larger if needed. If it is * 0 we skip the address write cycle. * * Typical case is a Write of an addr followd by a Read. The * IBM FAQ does not cover this. On the last byte of the write * we don't set the creg CHT bit, and on the first bytes of the * read we set the RPST bit. * * It does not support address only transfers, there must be * a data part. If you want to write the address yourself, put * it in the data pointer. * * It does not support transfer to/from address 0. * * It does not check XFRCNT. */ static int i2c_transfer(unsigned char cmd_type, unsigned char chip, unsigned char addr[], unsigned char addr_len, unsigned char data[], unsigned short data_len) { unsigned char* ptr; int reading; int tran,cnt; int result; int status; int i; uchar creg; if (data == 0 || data_len == 0) { /* Don't support data transfer of no length or to address 0 */ printf( "i2c_transfer: bad call\n" ); return IIC_NOK; } if (addr && addr_len) { ptr = addr; cnt = addr_len; reading = 0; } else { ptr = data; cnt = data_len; reading = cmd_type; } /* Clear Stop Complete Bit */ out_8((u8 *)IIC_STS, IIC_STS_SCMP); /* Check init */ i = 10; do { /* Get status */ status = in_8((u8 *)IIC_STS); i--; } while ((status & IIC_STS_PT) && (i > 0)); if (status & IIC_STS_PT) { result = IIC_NOK_TOUT; return(result); } /* flush the Master/Slave Databuffers */ out_8((u8 *)IIC_MDCNTL, ((in_8((u8 *)IIC_MDCNTL))|IIC_MDCNTL_FMDB|IIC_MDCNTL_FSDB)); /* need to wait 4 OPB clocks? code below should take that long */ /* 7-bit adressing */ out_8((u8 *)IIC_HMADR, 0); out_8((u8 *)IIC_LMADR, chip); tran = 0; result = IIC_OK; creg = 0; while (tran != cnt && (result == IIC_OK)) { int bc,j; /* Control register = * Normal transfer, 7-bits adressing, Transfer up to bc bytes, Normal start, * Transfer is a sequence of transfers */ creg |= IIC_CNTL_PT; bc = (cnt - tran) > 4 ? 4 : cnt - tran; creg |= (bc - 1) << 4; /* if the real cmd type is write continue trans */ if ((!cmd_type && (ptr == addr)) || ((tran + bc) != cnt)) creg |= IIC_CNTL_CHT; if (reading) creg |= IIC_CNTL_READ; else for(j=0; j < bc; j++) /* Set buffer */ out_8((u8 *)IIC_MDBUF, ptr[tran+j]); out_8((u8 *)IIC_CNTL, creg); /* Transfer is in progress * we have to wait for upto 5 bytes of data * 1 byte chip address+r/w bit then bc bytes * of data. * udelay(10) is 1 bit time at 100khz * Doubled for slop. 20 is too small. */ i = 2*5*8; do { /* Get status */ status = in_8((u8 *)IIC_STS); udelay(10); i--; } while ((status & IIC_STS_PT) && !(status & IIC_STS_ERR) && (i > 0)); if (status & IIC_STS_ERR) { result = IIC_NOK; status = in_8((u8 *)IIC_EXTSTS); /* Lost arbitration? */ if (status & IIC_EXTSTS_LA) result = IIC_NOK_LA; /* Incomplete transfer? */ if (status & IIC_EXTSTS_ICT) result = IIC_NOK_ICT; /* Transfer aborted? */ if (status & IIC_EXTSTS_XFRA) result = IIC_NOK_XFRA; } else if ( status & IIC_STS_PT) { result = IIC_NOK_TOUT; } /* Command is reading => get buffer */ if ((reading) && (result == IIC_OK)) { /* Are there data in buffer */ if (status & IIC_STS_MDBS) { /* * even if we have data we have to wait 4OPB clocks * for it to hit the front of the FIFO, after that * we can just read. We should check XFCNT here and * if the FIFO is full there is no need to wait. */ udelay(1); for (j=0; j<bc; j++) ptr[tran+j] = in_8((u8 *)IIC_MDBUF); } else result = IIC_NOK_DATA; } creg = 0; tran += bc; if (ptr == addr && tran == cnt) { ptr = data; cnt = data_len; tran = 0; reading = cmd_type; if (reading) creg = IIC_CNTL_RPST; } } return (result); } int i2c_probe(uchar chip) { uchar buf[1]; buf[0] = 0; /* * What is needed is to send the chip address and verify that the * address was <ACK>ed (i.e. there was a chip at that address which * drove the data line low). */ return (i2c_transfer(1, chip << 1, 0,0, buf, 1) != 0); } int i2c_read(uchar chip, uint addr, int alen, uchar * buffer, int len) { uchar xaddr[4]; int ret; if (alen > 4) { printf ("I2C read: addr len %d not supported\n", alen); return 1; } if (alen > 0) { xaddr[0] = (addr >> 24) & 0xFF; xaddr[1] = (addr >> 16) & 0xFF; xaddr[2] = (addr >> 8) & 0xFF; xaddr[3] = addr & 0xFF; } #ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW /* * EEPROM chips that implement "address overflow" are ones * like Catalyst 24WC04/08/16 which has 9/10/11 bits of * address and the extra bits end up in the "chip address" * bit slots. This makes a 24WC08 (1Kbyte) chip look like * four 256 byte chips. * * Note that we consider the length of the address field to * still be one byte because the extra address bits are * hidden in the chip address. */ if (alen > 0) chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); #endif if ((ret = i2c_transfer(1, chip<<1, &xaddr[4-alen], alen, buffer, len)) != 0) { if (gd->have_console) printf( "I2c read: failed %d\n", ret); return 1; } return 0; } int i2c_write(uchar chip, uint addr, int alen, uchar * buffer, int len) { uchar xaddr[4]; if (alen > 4) { printf ("I2C write: addr len %d not supported\n", alen); return 1; } if (alen > 0) { xaddr[0] = (addr >> 24) & 0xFF; xaddr[1] = (addr >> 16) & 0xFF; xaddr[2] = (addr >> 8) & 0xFF; xaddr[3] = addr & 0xFF; } #ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW /* * EEPROM chips that implement "address overflow" are ones * like Catalyst 24WC04/08/16 which has 9/10/11 bits of * address and the extra bits end up in the "chip address" * bit slots. This makes a 24WC08 (1Kbyte) chip look like * four 256 byte chips. * * Note that we consider the length of the address field to * still be one byte because the extra address bits are * hidden in the chip address. */ if (alen > 0) chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); #endif return (i2c_transfer(0, chip<<1, &xaddr[4-alen], alen, buffer, len ) != 0); } #if defined(CONFIG_I2C_MULTI_BUS) /* * Functions for multiple I2C bus handling */ unsigned int i2c_get_bus_num(void) { return i2c_bus_num; } int i2c_set_bus_num(unsigned int bus) { if (bus >= CONFIG_SYS_MAX_I2C_BUS) return -1; i2c_bus_num = bus; return 0; } #endif /* CONFIG_I2C_MULTI_BUS */ /* TODO: add 100/400k switching */ unsigned int i2c_get_bus_speed(void) { return CONFIG_SYS_I2C_SPEED; } int i2c_set_bus_speed(unsigned int speed) { if (speed != CONFIG_SYS_I2C_SPEED) return -1; return 0; } #endif /* CONFIG_HARD_I2C */