/* * cpu/ppc4xx/denali_spd_ddr2.c * This SPD SDRAM detection code supports AMCC PPC44x CPUs with a Denali-core * DDR2 controller, specifically the 440EPx/GRx. * * (C) Copyright 2007-2008 * Larry Johnson, lrj@acm.org. * * Based primarily on cpu/ppc4xx/4xx_spd_ddr2.c, which is... * * (C) Copyright 2007 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * COPYRIGHT AMCC CORPORATION 2004 * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA * */ /* define DEBUG for debugging output (obviously ;-)) */ #if 0 #define DEBUG #endif #include <common.h> #include <command.h> #include <ppc4xx.h> #include <i2c.h> #include <asm/io.h> #include <asm/processor.h> #include <asm/mmu.h> #include <asm/cache.h> #if defined(CONFIG_SPD_EEPROM) && \ (defined(CONFIG_440EPX) || defined(CONFIG_440GRX)) /*-----------------------------------------------------------------------------+ * Defines *-----------------------------------------------------------------------------*/ #ifndef TRUE #define TRUE 1 #endif #ifndef FALSE #define FALSE 0 #endif #define MAXDIMMS 2 #define MAXRANKS 2 #define ONE_BILLION 1000000000 #define MULDIV64(m1, m2, d) (u32)(((u64)(m1) * (u64)(m2)) / (u64)(d)) #define DLL_DQS_DELAY 0x19 #define DLL_DQS_BYPASS 0x0B #define DQS_OUT_SHIFT 0x7F /* * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory * region. Right now the cache should still be disabled in U-Boot because of the * EMAC driver, that need it's buffer descriptor to be located in non cached * memory. * * If at some time this restriction doesn't apply anymore, just define * CONFIG_4xx_DCACHE in the board config file and this code should setup * everything correctly. */ #if defined(CONFIG_4xx_DCACHE) #define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on SDRAM */ #else #define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */ #endif /*-----------------------------------------------------------------------------+ * Prototypes *-----------------------------------------------------------------------------*/ extern int denali_wait_for_dlllock(void); extern void denali_core_search_data_eye(void); extern void dcbz_area(u32 start_address, u32 num_bytes); /* * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed */ void __spd_ddr_init_hang(void) { hang(); } void spd_ddr_init_hang(void) __attribute__ ((weak, alias("__spd_ddr_init_hang"))); #if defined(DEBUG) static void print_mcsr(void) { printf("MCSR = 0x%08X\n", mfspr(SPRN_MCSR)); } static void denali_sdram_register_dump(void) { unsigned int sdram_data; printf("\n Register Dump:\n"); mfsdram(DDR0_00, sdram_data); printf(" DDR0_00 = 0x%08X", sdram_data); mfsdram(DDR0_01, sdram_data); printf(" DDR0_01 = 0x%08X\n", sdram_data); mfsdram(DDR0_02, sdram_data); printf(" DDR0_02 = 0x%08X", sdram_data); mfsdram(DDR0_03, sdram_data); printf(" DDR0_03 = 0x%08X\n", sdram_data); mfsdram(DDR0_04, sdram_data); printf(" DDR0_04 = 0x%08X", sdram_data); mfsdram(DDR0_05, sdram_data); printf(" DDR0_05 = 0x%08X\n", sdram_data); mfsdram(DDR0_06, sdram_data); printf(" DDR0_06 = 0x%08X", sdram_data); mfsdram(DDR0_07, sdram_data); printf(" DDR0_07 = 0x%08X\n", sdram_data); mfsdram(DDR0_08, sdram_data); printf(" DDR0_08 = 0x%08X", sdram_data); mfsdram(DDR0_09, sdram_data); printf(" DDR0_09 = 0x%08X\n", sdram_data); mfsdram(DDR0_10, sdram_data); printf(" DDR0_10 = 0x%08X", sdram_data); mfsdram(DDR0_11, sdram_data); printf(" DDR0_11 = 0x%08X\n", sdram_data); mfsdram(DDR0_12, sdram_data); printf(" DDR0_12 = 0x%08X", sdram_data); mfsdram(DDR0_14, sdram_data); printf(" DDR0_14 = 0x%08X\n", sdram_data); mfsdram(DDR0_17, sdram_data); printf(" DDR0_17 = 0x%08X", sdram_data); mfsdram(DDR0_18, sdram_data); printf(" DDR0_18 = 0x%08X\n", sdram_data); mfsdram(DDR0_19, sdram_data); printf(" DDR0_19 = 0x%08X", sdram_data); mfsdram(DDR0_20, sdram_data); printf(" DDR0_20 = 0x%08X\n", sdram_data); mfsdram(DDR0_21, sdram_data); printf(" DDR0_21 = 0x%08X", sdram_data); mfsdram(DDR0_22, sdram_data); printf(" DDR0_22 = 0x%08X\n", sdram_data); mfsdram(DDR0_23, sdram_data); printf(" DDR0_23 = 0x%08X", sdram_data); mfsdram(DDR0_24, sdram_data); printf(" DDR0_24 = 0x%08X\n", sdram_data); mfsdram(DDR0_25, sdram_data); printf(" DDR0_25 = 0x%08X", sdram_data); mfsdram(DDR0_26, sdram_data); printf(" DDR0_26 = 0x%08X\n", sdram_data); mfsdram(DDR0_27, sdram_data); printf(" DDR0_27 = 0x%08X", sdram_data); mfsdram(DDR0_28, sdram_data); printf(" DDR0_28 = 0x%08X\n", sdram_data); mfsdram(DDR0_31, sdram_data); printf(" DDR0_31 = 0x%08X", sdram_data); mfsdram(DDR0_32, sdram_data); printf(" DDR0_32 = 0x%08X\n", sdram_data); mfsdram(DDR0_33, sdram_data); printf(" DDR0_33 = 0x%08X", sdram_data); mfsdram(DDR0_34, sdram_data); printf(" DDR0_34 = 0x%08X\n", sdram_data); mfsdram(DDR0_35, sdram_data); printf(" DDR0_35 = 0x%08X", sdram_data); mfsdram(DDR0_36, sdram_data); printf(" DDR0_36 = 0x%08X\n", sdram_data); mfsdram(DDR0_37, sdram_data); printf(" DDR0_37 = 0x%08X", sdram_data); mfsdram(DDR0_38, sdram_data); printf(" DDR0_38 = 0x%08X\n", sdram_data); mfsdram(DDR0_39, sdram_data); printf(" DDR0_39 = 0x%08X", sdram_data); mfsdram(DDR0_40, sdram_data); printf(" DDR0_40 = 0x%08X\n", sdram_data); mfsdram(DDR0_41, sdram_data); printf(" DDR0_41 = 0x%08X", sdram_data); mfsdram(DDR0_42, sdram_data); printf(" DDR0_42 = 0x%08X\n", sdram_data); mfsdram(DDR0_43, sdram_data); printf(" DDR0_43 = 0x%08X", sdram_data); mfsdram(DDR0_44, sdram_data); printf(" DDR0_44 = 0x%08X\n", sdram_data); } #else static inline void denali_sdram_register_dump(void) { } inline static void print_mcsr(void) { } #endif /* defined(DEBUG) */ static int is_ecc_enabled(void) { u32 val; mfsdram(DDR0_22, val); return 0x3 == DDR0_22_CTRL_RAW_DECODE(val); } static unsigned char spd_read(u8 chip, unsigned int addr) { u8 data[2]; if (0 != i2c_probe(chip) || 0 != i2c_read(chip, addr, 1, data, 1)) { debug("spd_read(0x%02X, 0x%02X) failed\n", chip, addr); return 0; } debug("spd_read(0x%02X, 0x%02X) returned 0x%02X\n", chip, addr, data[0]); return data[0]; } static unsigned long get_tcyc(unsigned char reg) { /* * Byte 9, et al: Cycle time for CAS Latency=X, is split into two * nibbles: the higher order nibble (bits 4-7) designates the cycle time * to a granularity of 1ns; the value presented by the lower order * nibble (bits 0-3) has a granularity of .1ns and is added to the value * designated by the higher nibble. In addition, four lines of the lower * order nibble are assigned to support +.25, +.33, +.66, and +.75. */ unsigned char subfield_b = reg & 0x0F; switch (subfield_b & 0x0F) { case 0x0: case 0x1: case 0x2: case 0x3: case 0x4: case 0x5: case 0x6: case 0x7: case 0x8: case 0x9: return 1000 * (reg >> 4) + 100 * subfield_b; case 0xA: return 1000 * (reg >> 4) + 250; case 0xB: return 1000 * (reg >> 4) + 333; case 0xC: return 1000 * (reg >> 4) + 667; case 0xD: return 1000 * (reg >> 4) + 750; } return 0; } /*------------------------------------------------------------------ * Find the installed DIMMs, make sure that the are DDR2, and fill * in the dimm_ranks array. Then dimm_ranks[dimm_num] > 0 iff the * DIMM and dimm_num is present. * Note: Because there are only two chip-select lines, it is assumed * that a board with a single socket can support two ranks on that * socket, while a board with two sockets can support only one rank * on each socket. *-----------------------------------------------------------------*/ static void get_spd_info(unsigned long dimm_ranks[], unsigned long *ranks, unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks) { unsigned long dimm_num; unsigned long dimm_found = FALSE; unsigned long const max_ranks_per_dimm = (1 == num_dimm_banks) ? 2 : 1; unsigned char num_of_bytes; unsigned char total_size; *ranks = 0; for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { num_of_bytes = 0; total_size = 0; num_of_bytes = spd_read(iic0_dimm_addr[dimm_num], 0); total_size = spd_read(iic0_dimm_addr[dimm_num], 1); if ((num_of_bytes != 0) && (total_size != 0)) { unsigned char const dimm_type = spd_read(iic0_dimm_addr[dimm_num], 2); unsigned long ranks_on_dimm = (spd_read(iic0_dimm_addr[dimm_num], 5) & 0x07) + 1; if (8 != dimm_type) { switch (dimm_type) { case 1: printf("ERROR: Standard Fast Page Mode " "DRAM DIMM"); break; case 2: printf("ERROR: EDO DIMM"); break; case 3: printf("ERROR: Pipelined Nibble DIMM"); break; case 4: printf("ERROR: SDRAM DIMM"); break; case 5: printf("ERROR: Multiplexed ROM DIMM"); break; case 6: printf("ERROR: SGRAM DIMM"); break; case 7: printf("ERROR: DDR1 DIMM"); break; default: printf("ERROR: Unknown DIMM (type %d)", (unsigned int)dimm_type); break; } printf(" detected in slot %lu.\n", dimm_num); printf("Only DDR2 SDRAM DIMMs are supported." "\n"); printf("Replace the module with a DDR2 DIMM." "\n\n"); spd_ddr_init_hang(); } dimm_found = TRUE; debug("DIMM slot %lu: populated with %lu-rank DDR2 DIMM" "\n", dimm_num, ranks_on_dimm); if (ranks_on_dimm > max_ranks_per_dimm) { printf("WARNING: DRAM DIMM in slot %lu has %lu " "ranks.\n", dimm_num, ranks_on_dimm); if (1 == max_ranks_per_dimm) { printf("Only one rank will be used.\n"); } else { printf ("Only two ranks will be used.\n"); } ranks_on_dimm = max_ranks_per_dimm; } dimm_ranks[dimm_num] = ranks_on_dimm; *ranks += ranks_on_dimm; } else { dimm_ranks[dimm_num] = 0; debug("DIMM slot %lu: Not populated\n", dimm_num); } } if (dimm_found == FALSE) { printf("ERROR: No memory installed.\n"); printf("Install at least one DDR2 DIMM.\n\n"); spd_ddr_init_hang(); } debug("Total number of ranks = %d\n", *ranks); } /*------------------------------------------------------------------ * For the memory DIMMs installed, this routine verifies that * frequency previously calculated is supported. *-----------------------------------------------------------------*/ static void check_frequency(unsigned long *dimm_ranks, unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long sdram_freq) { unsigned long dimm_num; unsigned long cycle_time; unsigned long calc_cycle_time; /* * calc_cycle_time is calculated from DDR frequency set by board/chip * and is expressed in picoseconds to match the way DIMM cycle time is * calculated below. */ calc_cycle_time = MULDIV64(ONE_BILLION, 1000, sdram_freq); for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { if (dimm_ranks[dimm_num]) { cycle_time = get_tcyc(spd_read(iic0_dimm_addr[dimm_num], 9)); debug("cycle_time=%d ps\n", cycle_time); if (cycle_time > (calc_cycle_time + 10)) { /* * the provided sdram cycle_time is too small * for the available DIMM cycle_time. The * additionnal 10ps is here to accept a small * incertainty. */ printf ("ERROR: DRAM DIMM detected with cycle_time %d ps in " "slot %d \n while calculated cycle time is %d ps.\n", (unsigned int)cycle_time, (unsigned int)dimm_num, (unsigned int)calc_cycle_time); printf ("Replace the DIMM, or change DDR frequency via " "strapping bits.\n\n"); spd_ddr_init_hang(); } } } } /*------------------------------------------------------------------ * This routine gets size information for the installed memory * DIMMs. *-----------------------------------------------------------------*/ static void get_dimm_size(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long *const rows, unsigned long *const banks, unsigned long *const cols, unsigned long *const width) { unsigned long dimm_num; *rows = 0; *banks = 0; *cols = 0; *width = 0; for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { if (dimm_ranks[dimm_num]) { unsigned long t; /* Rows */ t = spd_read(iic0_dimm_addr[dimm_num], 3); if (0 == *rows) { *rows = t; } else if (t != *rows) { printf("ERROR: DRAM DIMM modules do not all " "have the same number of rows.\n\n"); spd_ddr_init_hang(); } /* Banks */ t = spd_read(iic0_dimm_addr[dimm_num], 17); if (0 == *banks) { *banks = t; } else if (t != *banks) { printf("ERROR: DRAM DIMM modules do not all " "have the same number of banks.\n\n"); spd_ddr_init_hang(); } /* Columns */ t = spd_read(iic0_dimm_addr[dimm_num], 4); if (0 == *cols) { *cols = t; } else if (t != *cols) { printf("ERROR: DRAM DIMM modules do not all " "have the same number of columns.\n\n"); spd_ddr_init_hang(); } /* Data width */ t = spd_read(iic0_dimm_addr[dimm_num], 6); if (0 == *width) { *width = t; } else if (t != *width) { printf("ERROR: DRAM DIMM modules do not all " "have the same data width.\n\n"); spd_ddr_init_hang(); } } } debug("Number of rows = %d\n", *rows); debug("Number of columns = %d\n", *cols); debug("Number of banks = %d\n", *banks); debug("Data width = %d\n", *width); if (*rows > 14) { printf("ERROR: DRAM DIMM modules have %lu address rows.\n", *rows); printf("Only modules with 14 or fewer rows are supported.\n\n"); spd_ddr_init_hang(); } if (4 != *banks && 8 != *banks) { printf("ERROR: DRAM DIMM modules have %lu banks.\n", *banks); printf("Only modules with 4 or 8 banks are supported.\n\n"); spd_ddr_init_hang(); } if (*cols > 12) { printf("ERROR: DRAM DIMM modules have %lu address columns.\n", *cols); printf("Only modules with 12 or fewer columns are " "supported.\n\n"); spd_ddr_init_hang(); } if (32 != *width && 40 != *width && 64 != *width && 72 != *width) { printf("ERROR: DRAM DIMM modules have a width of %lu bit.\n", *width); printf("Only modules with widths of 32, 40, 64, and 72 bits " "are supported.\n\n"); spd_ddr_init_hang(); } } /*------------------------------------------------------------------ * Only 1.8V modules are supported. This routine verifies this. *-----------------------------------------------------------------*/ static void check_voltage_type(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks) { unsigned long dimm_num; unsigned long voltage_type; for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { if (dimm_ranks[dimm_num]) { voltage_type = spd_read(iic0_dimm_addr[dimm_num], 8); if (0x05 != voltage_type) { /* 1.8V for DDR2 */ printf("ERROR: Slot %lu provides 1.8V for DDR2 " "DIMMs.\n", dimm_num); switch (voltage_type) { case 0x00: printf("This DIMM is 5.0 Volt/TTL.\n"); break; case 0x01: printf("This DIMM is LVTTL.\n"); break; case 0x02: printf("This DIMM is 1.5 Volt.\n"); break; case 0x03: printf("This DIMM is 3.3 Volt/TTL.\n"); break; case 0x04: printf("This DIMM is 2.5 Volt.\n"); break; default: printf("This DIMM is an unknown " "voltage.\n"); break; } printf("Replace it with a 1.8V DDR2 DIMM.\n\n"); spd_ddr_init_hang(); } } } } static void program_ddr0_03(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long sdram_freq, unsigned long rows, unsigned long *cas_latency) { unsigned long dimm_num; unsigned long cas_index; unsigned long cycle_2_0_clk; unsigned long cycle_3_0_clk; unsigned long cycle_4_0_clk; unsigned long cycle_5_0_clk; unsigned long max_2_0_tcyc_ps = 100; unsigned long max_3_0_tcyc_ps = 100; unsigned long max_4_0_tcyc_ps = 100; unsigned long max_5_0_tcyc_ps = 100; unsigned char cas_available = 0x3C; /* value for DDR2 */ u32 ddr0_03 = DDR0_03_BSTLEN_ENCODE(0x2) | DDR0_03_INITAREF_ENCODE(0x2); unsigned int const tcyc_addr[3] = { 9, 23, 25 }; /*------------------------------------------------------------------ * Get the board configuration info. *-----------------------------------------------------------------*/ debug("sdram_freq = %d\n", sdram_freq); /*------------------------------------------------------------------ * Handle the timing. We need to find the worst case timing of all * the dimm modules installed. *-----------------------------------------------------------------*/ /* loop through all the DIMM slots on the board */ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { /* If a dimm is installed in a particular slot ... */ if (dimm_ranks[dimm_num]) { unsigned char const cas_bit = spd_read(iic0_dimm_addr[dimm_num], 18); unsigned char cas_mask; cas_available &= cas_bit; for (cas_mask = 0x80; cas_mask; cas_mask >>= 1) { if (cas_bit & cas_mask) break; } debug("cas_bit (SPD byte 18) = %02X, cas_mask = %02X\n", cas_bit, cas_mask); for (cas_index = 0; cas_index < 3; cas_mask >>= 1, cas_index++) { unsigned long cycle_time_ps; if (!(cas_available & cas_mask)) { continue; } cycle_time_ps = get_tcyc(spd_read(iic0_dimm_addr[dimm_num], tcyc_addr[cas_index])); debug("cas_index = %d: cycle_time_ps = %d\n", cas_index, cycle_time_ps); /* * DDR2 devices use the following bitmask for CAS latency: * Bit 7 6 5 4 3 2 1 0 * TBD 6.0 5.0 4.0 3.0 2.0 TBD TBD */ switch (cas_mask) { case 0x20: max_5_0_tcyc_ps = max(max_5_0_tcyc_ps, cycle_time_ps); break; case 0x10: max_4_0_tcyc_ps = max(max_4_0_tcyc_ps, cycle_time_ps); break; case 0x08: max_3_0_tcyc_ps = max(max_3_0_tcyc_ps, cycle_time_ps); break; case 0x04: max_2_0_tcyc_ps = max(max_2_0_tcyc_ps, cycle_time_ps); break; } } } } debug("cas_available (bit map) = 0x%02X\n", cas_available); /*------------------------------------------------------------------ * Set the SDRAM mode, SDRAM_MMODE *-----------------------------------------------------------------*/ /* add 10 here because of rounding problems */ cycle_2_0_clk = MULDIV64(ONE_BILLION, 1000, max_2_0_tcyc_ps) + 10; cycle_3_0_clk = MULDIV64(ONE_BILLION, 1000, max_3_0_tcyc_ps) + 10; cycle_4_0_clk = MULDIV64(ONE_BILLION, 1000, max_4_0_tcyc_ps) + 10; cycle_5_0_clk = MULDIV64(ONE_BILLION, 1000, max_5_0_tcyc_ps) + 10; debug("cycle_2_0_clk = %d\n", cycle_2_0_clk); debug("cycle_3_0_clk = %d\n", cycle_3_0_clk); debug("cycle_4_0_clk = %d\n", cycle_4_0_clk); debug("cycle_5_0_clk = %d\n", cycle_5_0_clk); if ((cas_available & 0x04) && (sdram_freq <= cycle_2_0_clk)) { *cas_latency = 2; ddr0_03 |= DDR0_03_CASLAT_ENCODE(0x2) | DDR0_03_CASLAT_LIN_ENCODE(0x4); } else if ((cas_available & 0x08) && (sdram_freq <= cycle_3_0_clk)) { *cas_latency = 3; ddr0_03 |= DDR0_03_CASLAT_ENCODE(0x3) | DDR0_03_CASLAT_LIN_ENCODE(0x6); } else if ((cas_available & 0x10) && (sdram_freq <= cycle_4_0_clk)) { *cas_latency = 4; ddr0_03 |= DDR0_03_CASLAT_ENCODE(0x4) | DDR0_03_CASLAT_LIN_ENCODE(0x8); } else if ((cas_available & 0x20) && (sdram_freq <= cycle_5_0_clk)) { *cas_latency = 5; ddr0_03 |= DDR0_03_CASLAT_ENCODE(0x5) | DDR0_03_CASLAT_LIN_ENCODE(0xA); } else { printf("ERROR: Cannot find a supported CAS latency with the " "installed DIMMs.\n"); printf("Only DDR2 DIMMs with CAS latencies of 2.0, 3.0, 4.0, " "and 5.0 are supported.\n"); printf("Make sure the PLB speed is within the supported range " "of the DIMMs.\n"); printf("sdram_freq=%ld cycle2=%ld cycle3=%ld cycle4=%ld " "cycle5=%ld\n\n", sdram_freq, cycle_2_0_clk, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk); spd_ddr_init_hang(); } debug("CAS latency = %d\n", *cas_latency); mtsdram(DDR0_03, ddr0_03); } static void program_ddr0_04(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long sdram_freq) { unsigned long dimm_num; unsigned long t_rc_ps = 0; unsigned long t_rrd_ps = 0; unsigned long t_rtp_ps = 0; unsigned long t_rc_clk; unsigned long t_rrd_clk; unsigned long t_rtp_clk; /*------------------------------------------------------------------ * Handle the timing. We need to find the worst case timing of all * the dimm modules installed. *-----------------------------------------------------------------*/ /* loop through all the DIMM slots on the board */ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { /* If a dimm is installed in a particular slot ... */ if (dimm_ranks[dimm_num]) { unsigned long ps; /* tRC */ ps = 1000 * spd_read(iic0_dimm_addr[dimm_num], 41); switch (spd_read(iic0_dimm_addr[dimm_num], 40) >> 4) { case 0x1: ps += 250; break; case 0x2: ps += 333; break; case 0x3: ps += 500; break; case 0x4: ps += 667; break; case 0x5: ps += 750; break; } t_rc_ps = max(t_rc_ps, ps); /* tRRD */ ps = 250 * spd_read(iic0_dimm_addr[dimm_num], 28); t_rrd_ps = max(t_rrd_ps, ps); /* tRTP */ ps = 250 * spd_read(iic0_dimm_addr[dimm_num], 38); t_rtp_ps = max(t_rtp_ps, ps); } } debug("t_rc_ps = %d\n", t_rc_ps); t_rc_clk = (MULDIV64(sdram_freq, t_rc_ps, ONE_BILLION) + 999) / 1000; debug("t_rrd_ps = %d\n", t_rrd_ps); t_rrd_clk = (MULDIV64(sdram_freq, t_rrd_ps, ONE_BILLION) + 999) / 1000; debug("t_rtp_ps = %d\n", t_rtp_ps); t_rtp_clk = (MULDIV64(sdram_freq, t_rtp_ps, ONE_BILLION) + 999) / 1000; mtsdram(DDR0_04, DDR0_04_TRC_ENCODE(t_rc_clk) | DDR0_04_TRRD_ENCODE(t_rrd_clk) | DDR0_04_TRTP_ENCODE(t_rtp_clk)); } static void program_ddr0_05(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long sdram_freq) { unsigned long dimm_num; unsigned long t_rp_ps = 0; unsigned long t_ras_ps = 0; unsigned long t_rp_clk; unsigned long t_ras_clk; u32 ddr0_05 = DDR0_05_TMRD_ENCODE(0x2) | DDR0_05_TEMRS_ENCODE(0x2); /*------------------------------------------------------------------ * Handle the timing. We need to find the worst case timing of all * the dimm modules installed. *-----------------------------------------------------------------*/ /* loop through all the DIMM slots on the board */ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { /* If a dimm is installed in a particular slot ... */ if (dimm_ranks[dimm_num]) { unsigned long ps; /* tRP */ ps = 250 * spd_read(iic0_dimm_addr[dimm_num], 27); t_rp_ps = max(t_rp_ps, ps); /* tRAS */ ps = 1000 * spd_read(iic0_dimm_addr[dimm_num], 30); t_ras_ps = max(t_ras_ps, ps); } } debug("t_rp_ps = %d\n", t_rp_ps); t_rp_clk = (MULDIV64(sdram_freq, t_rp_ps, ONE_BILLION) + 999) / 1000; debug("t_ras_ps = %d\n", t_ras_ps); t_ras_clk = (MULDIV64(sdram_freq, t_ras_ps, ONE_BILLION) + 999) / 1000; mtsdram(DDR0_05, ddr0_05 | DDR0_05_TRP_ENCODE(t_rp_clk) | DDR0_05_TRAS_MIN_ENCODE(t_ras_clk)); } static void program_ddr0_06(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long sdram_freq) { unsigned long dimm_num; unsigned char spd_40; unsigned long t_wtr_ps = 0; unsigned long t_rfc_ps = 0; unsigned long t_wtr_clk; unsigned long t_rfc_clk; u32 ddr0_06 = DDR0_06_WRITEINTERP_ENCODE(0x1) | DDR0_06_TDLL_ENCODE(200); /*------------------------------------------------------------------ * Handle the timing. We need to find the worst case timing of all * the dimm modules installed. *-----------------------------------------------------------------*/ /* loop through all the DIMM slots on the board */ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { /* If a dimm is installed in a particular slot ... */ if (dimm_ranks[dimm_num]) { unsigned long ps; /* tWTR */ ps = 250 * spd_read(iic0_dimm_addr[dimm_num], 37); t_wtr_ps = max(t_wtr_ps, ps); /* tRFC */ ps = 1000 * spd_read(iic0_dimm_addr[dimm_num], 42); spd_40 = spd_read(iic0_dimm_addr[dimm_num], 40); ps += 256000 * (spd_40 & 0x01); switch ((spd_40 & 0x0E) >> 1) { case 0x1: ps += 250; break; case 0x2: ps += 333; break; case 0x3: ps += 500; break; case 0x4: ps += 667; break; case 0x5: ps += 750; break; } t_rfc_ps = max(t_rfc_ps, ps); } } debug("t_wtr_ps = %d\n", t_wtr_ps); t_wtr_clk = (MULDIV64(sdram_freq, t_wtr_ps, ONE_BILLION) + 999) / 1000; debug("t_rfc_ps = %d\n", t_rfc_ps); t_rfc_clk = (MULDIV64(sdram_freq, t_rfc_ps, ONE_BILLION) + 999) / 1000; mtsdram(DDR0_06, ddr0_06 | DDR0_06_TWTR_ENCODE(t_wtr_clk) | DDR0_06_TRFC_ENCODE(t_rfc_clk)); } static void program_ddr0_10(unsigned long dimm_ranks[], unsigned long ranks) { unsigned long csmap; if (2 == ranks) { /* Both chip selects in use */ csmap = 0x03; } else { /* One chip select in use */ csmap = (1 == dimm_ranks[0]) ? 0x1 : 0x2; } mtsdram(DDR0_10, DDR0_10_WRITE_MODEREG_ENCODE(0x0) | DDR0_10_CS_MAP_ENCODE(csmap) | DDR0_10_OCD_ADJUST_PUP_CS_0_ENCODE(0)); } static void program_ddr0_11(unsigned long sdram_freq) { unsigned long const t_xsnr_ps = 200000; /* 200 ns */ unsigned long t_xsnr_clk; debug("t_xsnr_ps = %d\n", t_xsnr_ps); t_xsnr_clk = (MULDIV64(sdram_freq, t_xsnr_ps, ONE_BILLION) + 999) / 1000; mtsdram(DDR0_11, DDR0_11_SREFRESH_ENCODE(0) | DDR0_11_TXSNR_ENCODE(t_xsnr_clk) | DDR0_11_TXSR_ENCODE(200)); } static void program_ddr0_22(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long width) { #if defined(CONFIG_DDR_ECC) unsigned long dimm_num; unsigned long ecc_available = width >= 64; u32 ddr0_22 = DDR0_22_DQS_OUT_SHIFT_BYPASS_ENCODE(0x26) | DDR0_22_DQS_OUT_SHIFT_ENCODE(DQS_OUT_SHIFT) | DDR0_22_DLL_DQS_BYPASS_8_ENCODE(DLL_DQS_BYPASS); /* loop through all the DIMM slots on the board */ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { /* If a dimm is installed in a particular slot ... */ if (dimm_ranks[dimm_num]) { /* Check for ECC */ if (0 == (spd_read(iic0_dimm_addr[dimm_num], 11) & 0x02)) { ecc_available = FALSE; } } } if (ecc_available) { debug("ECC found on all DIMMs present\n"); mtsdram(DDR0_22, ddr0_22 | DDR0_22_CTRL_RAW_ENCODE(0x3)); } else { debug("ECC not found on some or all DIMMs present\n"); mtsdram(DDR0_22, ddr0_22 | DDR0_22_CTRL_RAW_ENCODE(0x0)); } #else mtsdram(DDR0_22, DDR0_22_CTRL_RAW_ENCODE(0x0) | DDR0_22_DQS_OUT_SHIFT_BYPASS_ENCODE(0x26) | DDR0_22_DQS_OUT_SHIFT_ENCODE(DQS_OUT_SHIFT) | DDR0_22_DLL_DQS_BYPASS_8_ENCODE(DLL_DQS_BYPASS)); #endif /* defined(CONFIG_DDR_ECC) */ } static void program_ddr0_24(unsigned long ranks) { u32 ddr0_24 = DDR0_24_RTT_PAD_TERMINATION_ENCODE(0x1) | /* 75 ohm */ DDR0_24_ODT_RD_MAP_CS1_ENCODE(0x0); if (2 == ranks) { /* Both chip selects in use */ ddr0_24 |= DDR0_24_ODT_WR_MAP_CS1_ENCODE(0x1) | DDR0_24_ODT_WR_MAP_CS0_ENCODE(0x2); } else { /* One chip select in use */ /* One of the two fields added to ddr0_24 is a "don't care" */ ddr0_24 |= DDR0_24_ODT_WR_MAP_CS1_ENCODE(0x2) | DDR0_24_ODT_WR_MAP_CS0_ENCODE(0x1); } mtsdram(DDR0_24, ddr0_24); } static void program_ddr0_26(unsigned long sdram_freq) { unsigned long const t_ref_ps = 7800000; /* 7.8 us. refresh */ /* TODO: check definition of tRAS_MAX */ unsigned long const t_ras_max_ps = 9 * t_ref_ps; unsigned long t_ras_max_clk; unsigned long t_ref_clk; /* Round down t_ras_max_clk and t_ref_clk */ debug("t_ras_max_ps = %d\n", t_ras_max_ps); t_ras_max_clk = MULDIV64(sdram_freq, t_ras_max_ps, ONE_BILLION) / 1000; debug("t_ref_ps = %d\n", t_ref_ps); t_ref_clk = MULDIV64(sdram_freq, t_ref_ps, ONE_BILLION) / 1000; mtsdram(DDR0_26, DDR0_26_TRAS_MAX_ENCODE(t_ras_max_clk) | DDR0_26_TREF_ENCODE(t_ref_clk)); } static void program_ddr0_27(unsigned long sdram_freq) { unsigned long const t_init_ps = 200000000; /* 200 us. init */ unsigned long t_init_clk; debug("t_init_ps = %d\n", t_init_ps); t_init_clk = (MULDIV64(sdram_freq, t_init_ps, ONE_BILLION) + 999) / 1000; mtsdram(DDR0_27, DDR0_27_EMRS_DATA_ENCODE(0x0000) | DDR0_27_TINIT_ENCODE(t_init_clk)); } static void program_ddr0_43(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long sdram_freq, unsigned long cols, unsigned long banks) { unsigned long dimm_num; unsigned long t_wr_ps = 0; unsigned long t_wr_clk; u32 ddr0_43 = DDR0_43_APREBIT_ENCODE(10) | DDR0_43_COLUMN_SIZE_ENCODE(12 - cols) | DDR0_43_EIGHT_BANK_MODE_ENCODE(8 == banks ? 1 : 0); /*------------------------------------------------------------------ * Handle the timing. We need to find the worst case timing of all * the dimm modules installed. *-----------------------------------------------------------------*/ /* loop through all the DIMM slots on the board */ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { /* If a dimm is installed in a particular slot ... */ if (dimm_ranks[dimm_num]) { unsigned long ps; ps = 250 * spd_read(iic0_dimm_addr[dimm_num], 36); t_wr_ps = max(t_wr_ps, ps); } } debug("t_wr_ps = %d\n", t_wr_ps); t_wr_clk = (MULDIV64(sdram_freq, t_wr_ps, ONE_BILLION) + 999) / 1000; mtsdram(DDR0_43, ddr0_43 | DDR0_43_TWR_ENCODE(t_wr_clk)); } static void program_ddr0_44(unsigned long dimm_ranks[], unsigned char const iic0_dimm_addr[], unsigned long num_dimm_banks, unsigned long sdram_freq) { unsigned long dimm_num; unsigned long t_rcd_ps = 0; unsigned long t_rcd_clk; /*------------------------------------------------------------------ * Handle the timing. We need to find the worst case timing of all * the dimm modules installed. *-----------------------------------------------------------------*/ /* loop through all the DIMM slots on the board */ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) { /* If a dimm is installed in a particular slot ... */ if (dimm_ranks[dimm_num]) { unsigned long ps; ps = 250 * spd_read(iic0_dimm_addr[dimm_num], 29); t_rcd_ps = max(t_rcd_ps, ps); } } debug("t_rcd_ps = %d\n", t_rcd_ps); t_rcd_clk = (MULDIV64(sdram_freq, t_rcd_ps, ONE_BILLION) + 999) / 1000; mtsdram(DDR0_44, DDR0_44_TRCD_ENCODE(t_rcd_clk)); } /*-----------------------------------------------------------------------------+ * initdram. Initializes the 440EPx/GPx DDR SDRAM controller. * Note: This routine runs from flash with a stack set up in the chip's * sram space. It is important that the routine does not require .sbss, .bss or * .data sections. It also cannot call routines that require these sections. *-----------------------------------------------------------------------------*/ /*----------------------------------------------------------------------------- * Function: initdram * Description: Configures SDRAM memory banks for DDR operation. * Auto Memory Configuration option reads the DDR SDRAM EEPROMs * via the IIC bus and then configures the DDR SDRAM memory * banks appropriately. If Auto Memory Configuration is * not used, it is assumed that no DIMM is plugged *-----------------------------------------------------------------------------*/ phys_size_t initdram(int board_type) { unsigned char const iic0_dimm_addr[] = SPD_EEPROM_ADDRESS; unsigned long dimm_ranks[MAXDIMMS]; unsigned long ranks; unsigned long rows; unsigned long banks; unsigned long cols; unsigned long width; unsigned long const sdram_freq = get_bus_freq(0); unsigned long const num_dimm_banks = sizeof(iic0_dimm_addr); /* on board dimm banks */ unsigned long cas_latency = 0; /* to quiet initialization warning */ unsigned long dram_size; debug("\nEntering initdram()\n"); /*------------------------------------------------------------------ * Stop the DDR-SDRAM controller. *-----------------------------------------------------------------*/ mtsdram(DDR0_02, DDR0_02_START_ENCODE(0)); /* * Make sure I2C controller is initialized * before continuing. */ /* switch to correct I2C bus */ I2C_SET_BUS(CFG_SPD_BUS_NUM); i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); /*------------------------------------------------------------------ * Clear out the serial presence detect buffers. * Perform IIC reads from the dimm. Fill in the spds. * Check to see if the dimm slots are populated *-----------------------------------------------------------------*/ get_spd_info(dimm_ranks, &ranks, iic0_dimm_addr, num_dimm_banks); /*------------------------------------------------------------------ * Check the frequency supported for the dimms plugged. *-----------------------------------------------------------------*/ check_frequency(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq); /*------------------------------------------------------------------ * Check and get size information. *-----------------------------------------------------------------*/ get_dimm_size(dimm_ranks, iic0_dimm_addr, num_dimm_banks, &rows, &banks, &cols, &width); /*------------------------------------------------------------------ * Check the voltage type for the dimms plugged. *-----------------------------------------------------------------*/ check_voltage_type(dimm_ranks, iic0_dimm_addr, num_dimm_banks); /*------------------------------------------------------------------ * Program registers for SDRAM controller. *-----------------------------------------------------------------*/ mtsdram(DDR0_00, DDR0_00_DLL_INCREMENT_ENCODE(0x19) | DDR0_00_DLL_START_POINT_DECODE(0x0A)); mtsdram(DDR0_01, DDR0_01_PLB0_DB_CS_LOWER_ENCODE(0x01) | DDR0_01_PLB0_DB_CS_UPPER_ENCODE(0x00) | DDR0_01_INT_MASK_ENCODE(0xFF)); program_ddr0_03(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq, rows, &cas_latency); program_ddr0_04(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq); program_ddr0_05(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq); program_ddr0_06(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq); /* * TODO: tFAW not found in SPD. Value of 13 taken from Sequoia * board SDRAM, but may be overly conservative. */ mtsdram(DDR0_07, DDR0_07_NO_CMD_INIT_ENCODE(0) | DDR0_07_TFAW_ENCODE(13) | DDR0_07_AUTO_REFRESH_MODE_ENCODE(1) | DDR0_07_AREFRESH_ENCODE(0)); mtsdram(DDR0_08, DDR0_08_WRLAT_ENCODE(cas_latency - 1) | DDR0_08_TCPD_ENCODE(200) | DDR0_08_DQS_N_EN_ENCODE(0) | DDR0_08_DDRII_ENCODE(1)); mtsdram(DDR0_09, DDR0_09_OCD_ADJUST_PDN_CS_0_ENCODE(0x00) | DDR0_09_RTT_0_ENCODE(0x1) | DDR0_09_WR_DQS_SHIFT_BYPASS_ENCODE(0x1D) | DDR0_09_WR_DQS_SHIFT_ENCODE(DQS_OUT_SHIFT - 0x20)); program_ddr0_10(dimm_ranks, ranks); program_ddr0_11(sdram_freq); mtsdram(DDR0_12, DDR0_12_TCKE_ENCODE(3)); mtsdram(DDR0_14, DDR0_14_DLL_BYPASS_MODE_ENCODE(0) | DDR0_14_REDUC_ENCODE(width <= 40 ? 1 : 0) | DDR0_14_REG_DIMM_ENABLE_ENCODE(0)); mtsdram(DDR0_17, DDR0_17_DLL_DQS_DELAY_0_ENCODE(DLL_DQS_DELAY)); mtsdram(DDR0_18, DDR0_18_DLL_DQS_DELAY_4_ENCODE(DLL_DQS_DELAY) | DDR0_18_DLL_DQS_DELAY_3_ENCODE(DLL_DQS_DELAY) | DDR0_18_DLL_DQS_DELAY_2_ENCODE(DLL_DQS_DELAY) | DDR0_18_DLL_DQS_DELAY_1_ENCODE(DLL_DQS_DELAY)); mtsdram(DDR0_19, DDR0_19_DLL_DQS_DELAY_8_ENCODE(DLL_DQS_DELAY) | DDR0_19_DLL_DQS_DELAY_7_ENCODE(DLL_DQS_DELAY) | DDR0_19_DLL_DQS_DELAY_6_ENCODE(DLL_DQS_DELAY) | DDR0_19_DLL_DQS_DELAY_5_ENCODE(DLL_DQS_DELAY)); mtsdram(DDR0_20, DDR0_20_DLL_DQS_BYPASS_3_ENCODE(DLL_DQS_BYPASS) | DDR0_20_DLL_DQS_BYPASS_2_ENCODE(DLL_DQS_BYPASS) | DDR0_20_DLL_DQS_BYPASS_1_ENCODE(DLL_DQS_BYPASS) | DDR0_20_DLL_DQS_BYPASS_0_ENCODE(DLL_DQS_BYPASS)); mtsdram(DDR0_21, DDR0_21_DLL_DQS_BYPASS_7_ENCODE(DLL_DQS_BYPASS) | DDR0_21_DLL_DQS_BYPASS_6_ENCODE(DLL_DQS_BYPASS) | DDR0_21_DLL_DQS_BYPASS_5_ENCODE(DLL_DQS_BYPASS) | DDR0_21_DLL_DQS_BYPASS_4_ENCODE(DLL_DQS_BYPASS)); program_ddr0_22(dimm_ranks, iic0_dimm_addr, num_dimm_banks, width); mtsdram(DDR0_23, DDR0_23_ODT_RD_MAP_CS0_ENCODE(0x0) | DDR0_23_FWC_ENCODE(0)); program_ddr0_24(ranks); program_ddr0_26(sdram_freq); program_ddr0_27(sdram_freq); mtsdram(DDR0_28, DDR0_28_EMRS3_DATA_ENCODE(0x0000) | DDR0_28_EMRS2_DATA_ENCODE(0x0000)); mtsdram(DDR0_31, DDR0_31_XOR_CHECK_BITS_ENCODE(0x0000)); mtsdram(DDR0_42, DDR0_42_ADDR_PINS_DECODE(14 - rows) | DDR0_42_CASLAT_LIN_GATE_ENCODE(2 * cas_latency)); program_ddr0_43(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq, cols, banks); program_ddr0_44(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq); denali_sdram_register_dump(); dram_size = (width >= 64) ? 8 : 4; dram_size *= 1 << cols; dram_size *= banks; dram_size *= 1 << rows; dram_size *= ranks; debug("dram_size = %lu\n", dram_size); /* Start the SDRAM controler */ mtsdram(DDR0_02, DDR0_02_START_ENCODE(1)); denali_wait_for_dlllock(); #if defined(CONFIG_DDR_DATA_EYE) /* * Map the first 1 MiB of memory in the TLB, and perform the data eye * search. */ program_tlb(0, CFG_SDRAM_BASE, TLB_1MB_SIZE, TLB_WORD2_I_ENABLE); denali_core_search_data_eye(); denali_sdram_register_dump(); remove_tlb(CFG_SDRAM_BASE, TLB_1MB_SIZE); #endif #if defined(CONFIG_ZERO_SDRAM) || defined(CONFIG_DDR_ECC) program_tlb(0, CFG_SDRAM_BASE, dram_size, 0); sync(); /* Zero the memory */ debug("Zeroing SDRAM..."); #if defined(CFG_MEM_TOP_HIDE) dcbz_area(CFG_SDRAM_BASE, dram_size - CFG_MEM_TOP_HIDE); #else #error Please define CFG_MEM_TOP_HIDE (see README) in your board config file #endif /* Write modified dcache lines back to memory */ clean_dcache_range(CFG_SDRAM_BASE, CFG_SDRAM_BASE + dram_size - CFG_MEM_TOP_HIDE); debug("Completed\n"); sync(); remove_tlb(CFG_SDRAM_BASE, dram_size); #if defined(CONFIG_DDR_ECC) /* * If ECC is enabled, clear and enable interrupts */ if (is_ecc_enabled()) { u32 val; sync(); /* Clear error status */ mfsdram(DDR0_00, val); mtsdram(DDR0_00, val | DDR0_00_INT_ACK_ALL); /* Set 'int_mask' parameter to functionnal value */ mfsdram(DDR0_01, val); mtsdram(DDR0_01, (val & ~DDR0_01_INT_MASK_MASK) | DDR0_01_INT_MASK_ALL_OFF); #if defined(CONFIG_DDR_DATA_EYE) /* * Running denali_core_search_data_eye() when ECC is enabled * causes non-ECC machine checks. This clears them. */ print_mcsr(); mtspr(SPRN_MCSR, mfspr(SPRN_MCSR)); print_mcsr(); #endif sync(); } #endif /* defined(CONFIG_DDR_ECC) */ #endif /* defined(CONFIG_ZERO_SDRAM) || defined(CONFIG_DDR_ECC) */ program_tlb(0, CFG_SDRAM_BASE, dram_size, MY_TLB_WORD2_I_ENABLE); return dram_size; } void board_add_ram_info(int use_default) { u32 val; printf(" (ECC"); if (!is_ecc_enabled()) { printf(" not"); } printf(" enabled, %ld MHz", (2 * get_bus_freq(0)) / 1000000); mfsdram(DDR0_03, val); printf(", CL%d)", DDR0_03_CASLAT_LIN_DECODE(val) >> 1); } #endif /* CONFIG_SPD_EEPROM */