/* * armboot - Startup Code for ARM720 CPU-core * * Copyright (c) 2001 Marius Gr�ger <mag@sysgo.de> * Copyright (c) 2002 Alex Z�pke <azu@sysgo.de> * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #include <config.h> #include <version.h> #include <asm/hardware.h> /* ************************************************************************* * * Jump vector table as in table 3.1 in [1] * ************************************************************************* */ .globl _start _start: b reset ldr pc, _undefined_instruction ldr pc, _software_interrupt ldr pc, _prefetch_abort ldr pc, _data_abort #ifdef CONFIG_LPC2292 .word 0xB4405F76 /* 2's complement of the checksum of the vectors */ #else ldr pc, _not_used #endif ldr pc, _irq ldr pc, _fiq _undefined_instruction: .word undefined_instruction _software_interrupt: .word software_interrupt _prefetch_abort: .word prefetch_abort _data_abort: .word data_abort _not_used: .word not_used _irq: .word irq _fiq: .word fiq .balignl 16,0xdeadbeef /* ************************************************************************* * * Startup Code (reset vector) * * do important init only if we don't start from RAM! * relocate armboot to ram * setup stack * jump to second stage * ************************************************************************* */ _TEXT_BASE: .word TEXT_BASE .globl _armboot_start _armboot_start: .word _start /* * These are defined in the board-specific linker script. */ .globl _bss_start _bss_start: .word __bss_start .globl _bss_end _bss_end: .word _end #ifdef CONFIG_USE_IRQ /* IRQ stack memory (calculated at run-time) */ .globl IRQ_STACK_START IRQ_STACK_START: .word 0x0badc0de /* IRQ stack memory (calculated at run-time) */ .globl FIQ_STACK_START FIQ_STACK_START: .word 0x0badc0de #endif /* * the actual reset code */ reset: /* * set the cpu to SVC32 mode */ mrs r0,cpsr bic r0,r0,#0x1f orr r0,r0,#0x13 msr cpsr,r0 /* * we do sys-critical inits only at reboot, * not when booting from ram! */ #ifndef CONFIG_SKIP_LOWLEVEL_INIT bl cpu_init_crit #endif #ifdef CONFIG_LPC2292 bl lowlevel_init #endif #ifndef CONFIG_SKIP_RELOCATE_UBOOT relocate: /* relocate U-Boot to RAM */ adr r0, _start /* r0 <- current position of code */ ldr r1, _TEXT_BASE /* test if we run from flash or RAM */ cmp r0, r1 /* don't reloc during debug */ beq stack_setup #if TEXT_BASE #ifndef CONFIG_LPC2292 /* already done in lowlevel_init */ ldr r2, =0x0 /* Relocate the exception vectors */ cmp r1, r2 /* and associated data to address */ ldmneia r0!, {r3-r10} /* 0x0. Do nothing if TEXT_BASE is */ stmneia r2!, {r3-r10} /* 0x0. Copy the first 15 words. */ ldmneia r0, {r3-r9} stmneia r2, {r3-r9} adrne r0, _start /* restore r0 */ #endif /* !CONFIG_LPC2292 */ #endif ldr r2, _armboot_start ldr r3, _bss_start sub r2, r3, r2 /* r2 <- size of armboot */ add r2, r0, r2 /* r2 <- source end address */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ cmp r0, r2 /* until source end addreee [r2] */ ble copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ stack_setup: ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */ sub r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area */ sub r0, r0, #CONFIG_SYS_GBL_DATA_SIZE /* bdinfo */ #ifdef CONFIG_USE_IRQ sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ) #endif sub sp, r0, #12 /* leave 3 words for abort-stack */ clear_bss: ldr r0, _bss_start /* find start of bss segment */ ldr r1, _bss_end /* stop here */ mov r2, #0x00000000 /* clear */ clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 ble clbss_l ldr pc, _start_armboot _start_armboot: .word start_armboot /* ************************************************************************* * * CPU_init_critical registers * * setup important registers * setup memory timing * ************************************************************************* */ #if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312) || defined(CONFIG_ARMADILLO) /* Interupt-Controller base addresses */ INTMR1: .word 0x80000280 @ 32 bit size INTMR2: .word 0x80001280 @ 16 bit size INTMR3: .word 0x80002280 @ 8 bit size /* SYSCONs */ SYSCON1: .word 0x80000100 SYSCON2: .word 0x80001100 SYSCON3: .word 0x80002200 #define CLKCTL 0x6 /* mask */ #define CLKCTL_18 0x0 /* 18.432 MHz */ #define CLKCTL_36 0x2 /* 36.864 MHz */ #define CLKCTL_49 0x4 /* 49.152 MHz */ #define CLKCTL_73 0x6 /* 73.728 MHz */ #elif defined(CONFIG_LPC2292) PLLCFG_ADR: .word PLLCFG PLLFEED_ADR: .word PLLFEED PLLCON_ADR: .word PLLCON PLLSTAT_ADR: .word PLLSTAT VPBDIV_ADR: .word VPBDIV MEMMAP_ADR: .word MEMMAP #endif cpu_init_crit: #if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312) || defined(CONFIG_ARMADILLO) /* * mask all IRQs by clearing all bits in the INTMRs */ mov r1, #0x00 ldr r0, INTMR1 str r1, [r0] ldr r0, INTMR2 str r1, [r0] ldr r0, INTMR3 str r1, [r0] /* * flush v4 I/D caches */ mov r0, #0 mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */ mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */ /* * disable MMU stuff and caches */ mrc p15,0,r0,c1,c0 bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS) bic r0, r0, #0x0000008f @ clear bits 7, 3:0 (B--- WCAM) orr r0, r0, #0x00000002 @ set bit 2 (A) Align mcr p15,0,r0,c1,c0 #elif defined(CONFIG_NETARM) /* * prior to software reset : need to set pin PORTC4 to be *HRESET */ ldr r0, =NETARM_GEN_MODULE_BASE ldr r1, =(NETARM_GEN_PORT_MODE(0x10) | \ NETARM_GEN_PORT_DIR(0x10)) str r1, [r0, #+NETARM_GEN_PORTC] /* * software reset : see HW Ref. Guide 8.2.4 : Software Service register * for an explanation of this process */ ldr r0, =NETARM_GEN_MODULE_BASE ldr r1, =NETARM_GEN_SW_SVC_RESETA str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE] ldr r1, =NETARM_GEN_SW_SVC_RESETB str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE] ldr r1, =NETARM_GEN_SW_SVC_RESETA str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE] ldr r1, =NETARM_GEN_SW_SVC_RESETB str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE] /* * setup PLL and System Config */ ldr r0, =NETARM_GEN_MODULE_BASE ldr r1, =( NETARM_GEN_SYS_CFG_LENDIAN | \ NETARM_GEN_SYS_CFG_BUSFULL | \ NETARM_GEN_SYS_CFG_USER_EN | \ NETARM_GEN_SYS_CFG_ALIGN_ABORT | \ NETARM_GEN_SYS_CFG_BUSARB_INT | \ NETARM_GEN_SYS_CFG_BUSMON_EN ) str r1, [r0, #+NETARM_GEN_SYSTEM_CONTROL] #ifndef CONFIG_NETARM_PLL_BYPASS ldr r1, =( NETARM_GEN_PLL_CTL_PLLCNT(NETARM_PLL_COUNT_VAL) | \ NETARM_GEN_PLL_CTL_POLTST_DEF | \ NETARM_GEN_PLL_CTL_INDIV(1) | \ NETARM_GEN_PLL_CTL_ICP_DEF | \ NETARM_GEN_PLL_CTL_OUTDIV(2) ) str r1, [r0, #+NETARM_GEN_PLL_CONTROL] #endif /* * mask all IRQs by clearing all bits in the INTMRs */ mov r1, #0 ldr r0, =NETARM_GEN_MODULE_BASE str r1, [r0, #+NETARM_GEN_INTR_ENABLE] #elif defined(CONFIG_S3C4510B) /* * Mask off all IRQ sources */ ldr r1, =REG_INTMASK ldr r0, =0x3FFFFF str r0, [r1] /* * Disable Cache */ ldr r0, =REG_SYSCFG ldr r1, =0x83ffffa0 /* cache-disabled */ str r1, [r0] #elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR) /* No specific initialisation for IntegratorAP/CM720T as yet */ #elif defined(CONFIG_LPC2292) /* Set-up PLL */ mov r3, #0xAA mov r4, #0x55 /* First disconnect and disable the PLL */ ldr r0, PLLCON_ADR mov r1, #0x00 str r1, [r0] ldr r0, PLLFEED_ADR /* start feed sequence */ str r3, [r0] str r4, [r0] /* feed sequence done */ /* Set new M and P values */ ldr r0, PLLCFG_ADR mov r1, #0x23 /* M=4 and P=2 */ str r1, [r0] ldr r0, PLLFEED_ADR /* start feed sequence */ str r3, [r0] str r4, [r0] /* feed sequence done */ /* Then enable the PLL */ ldr r0, PLLCON_ADR mov r1, #0x01 /* PLL enable bit */ str r1, [r0] ldr r0, PLLFEED_ADR /* start feed sequence */ str r3, [r0] str r4, [r0] /* feed sequence done */ /* Wait for the lock */ ldr r0, PLLSTAT_ADR mov r1, #0x400 /* lock bit */ lock_loop: ldr r2, [r0] and r2, r1, r2 cmp r2, #0 beq lock_loop /* And finally connect the PLL */ ldr r0, PLLCON_ADR mov r1, #0x03 /* PLL enable bit and connect bit */ str r1, [r0] ldr r0, PLLFEED_ADR /* start feed sequence */ str r3, [r0] str r4, [r0] /* feed sequence done */ /* Set-up VPBDIV register */ ldr r0, VPBDIV_ADR mov r1, #0x01 /* VPB clock is same as process clock */ str r1, [r0] #else #error No cpu_init_crit() defined for current CPU type #endif #ifdef CONFIG_ARM7_REVD /* set clock speed */ /* !!! we run @ 36 MHz due to a hardware flaw in Rev. D processors */ /* !!! not doing DRAM refresh properly! */ ldr r0, SYSCON3 ldr r1, [r0] bic r1, r1, #CLKCTL orr r1, r1, #CLKCTL_36 str r1, [r0] #endif #ifndef CONFIG_LPC2292 mov ip, lr /* * before relocating, we have to setup RAM timing * because memory timing is board-dependent, you will * find a lowlevel_init.S in your board directory. */ bl lowlevel_init mov lr, ip #endif mov pc, lr /* ************************************************************************* * * Interrupt handling * ************************************************************************* */ @ @ IRQ stack frame. @ #define S_FRAME_SIZE 72 #define S_OLD_R0 68 #define S_PSR 64 #define S_PC 60 #define S_LR 56 #define S_SP 52 #define S_IP 48 #define S_FP 44 #define S_R10 40 #define S_R9 36 #define S_R8 32 #define S_R7 28 #define S_R6 24 #define S_R5 20 #define S_R4 16 #define S_R3 12 #define S_R2 8 #define S_R1 4 #define S_R0 0 #define MODE_SVC 0x13 #define I_BIT 0x80 /* * use bad_save_user_regs for abort/prefetch/undef/swi ... * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling */ .macro bad_save_user_regs sub sp, sp, #S_FRAME_SIZE stmia sp, {r0 - r12} @ Calling r0-r12 add r8, sp, #S_PC ldr r2, _armboot_start sub r2, r2, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN) sub r2, r2, #(CONFIG_SYS_GBL_DATA_SIZE+8) @ set base 2 words into abort stack ldmia r2, {r2 - r4} @ get pc, cpsr, old_r0 add r0, sp, #S_FRAME_SIZE @ restore sp_SVC add r5, sp, #S_SP mov r1, lr stmia r5, {r0 - r4} @ save sp_SVC, lr_SVC, pc, cpsr, old_r mov r0, sp .endm .macro irq_save_user_regs sub sp, sp, #S_FRAME_SIZE stmia sp, {r0 - r12} @ Calling r0-r12 add r8, sp, #S_PC stmdb r8, {sp, lr}^ @ Calling SP, LR str lr, [r8, #0] @ Save calling PC mrs r6, spsr str r6, [r8, #4] @ Save CPSR str r0, [r8, #8] @ Save OLD_R0 mov r0, sp .endm .macro irq_restore_user_regs ldmia sp, {r0 - lr}^ @ Calling r0 - lr mov r0, r0 ldr lr, [sp, #S_PC] @ Get PC add sp, sp, #S_FRAME_SIZE subs pc, lr, #4 @ return & move spsr_svc into cpsr .endm .macro get_bad_stack ldr r13, _armboot_start @ setup our mode stack sub r13, r13, #(CONFIG_STACKSIZE+CONFIG_SYS_MALLOC_LEN) sub r13, r13, #(CONFIG_SYS_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack str lr, [r13] @ save caller lr / spsr mrs lr, spsr str lr, [r13, #4] mov r13, #MODE_SVC @ prepare SVC-Mode msr spsr_c, r13 mov lr, pc movs pc, lr .endm .macro get_irq_stack @ setup IRQ stack ldr sp, IRQ_STACK_START .endm .macro get_fiq_stack @ setup FIQ stack ldr sp, FIQ_STACK_START .endm /* * exception handlers */ .align 5 undefined_instruction: get_bad_stack bad_save_user_regs bl do_undefined_instruction .align 5 software_interrupt: get_bad_stack bad_save_user_regs bl do_software_interrupt .align 5 prefetch_abort: get_bad_stack bad_save_user_regs bl do_prefetch_abort .align 5 data_abort: get_bad_stack bad_save_user_regs bl do_data_abort .align 5 not_used: get_bad_stack bad_save_user_regs bl do_not_used #ifdef CONFIG_USE_IRQ .align 5 irq: get_irq_stack irq_save_user_regs bl do_irq irq_restore_user_regs .align 5 fiq: get_fiq_stack /* someone ought to write a more effiction fiq_save_user_regs */ irq_save_user_regs bl do_fiq irq_restore_user_regs #else .align 5 irq: get_bad_stack bad_save_user_regs bl do_irq .align 5 fiq: get_bad_stack bad_save_user_regs bl do_fiq #endif #if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312) || defined(CONFIG_ARMADILLO) .align 5 .globl reset_cpu reset_cpu: mov ip, #0 mcr p15, 0, ip, c7, c7, 0 @ invalidate cache mcr p15, 0, ip, c8, c7, 0 @ flush TLB (v4) mrc p15, 0, ip, c1, c0, 0 @ get ctrl register bic ip, ip, #0x000f @ ............wcam bic ip, ip, #0x2100 @ ..v....s........ mcr p15, 0, ip, c1, c0, 0 @ ctrl register mov pc, r0 #elif defined(CONFIG_NETARM) .align 5 .globl reset_cpu reset_cpu: ldr r1, =NETARM_MEM_MODULE_BASE ldr r0, [r1, #+NETARM_MEM_CS0_BASE_ADDR] ldr r1, =0xFFFFF000 and r0, r1, r0 ldr r1, =(relocate-TEXT_BASE) add r0, r1, r0 ldr r4, =NETARM_GEN_MODULE_BASE ldr r1, =NETARM_GEN_SW_SVC_RESETA str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE] ldr r1, =NETARM_GEN_SW_SVC_RESETB str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE] ldr r1, =NETARM_GEN_SW_SVC_RESETA str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE] ldr r1, =NETARM_GEN_SW_SVC_RESETB str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE] mov pc, r0 #elif defined(CONFIG_S3C4510B) /* Nothing done here as reseting the CPU is board specific, depending * on external peripherals such as watchdog timers, etc. */ #elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR) /* No specific reset actions for IntegratorAP/CM720T as yet */ #elif defined(CONFIG_LPC2292) .align 5 .globl reset_cpu reset_cpu: mov pc, r0 #else #error No reset_cpu() defined for current CPU type #endif