/* * (C) Copyright 2001 * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA * * * TODO: clean-up */ /* * How do I program the SDRAM Timing Register (SDRAM0_TR) for a specific SDRAM or DIMM? * * As an example, consider a case where PC133 memory with CAS Latency equal to 2 is being * used with a 200MHz 405GP. For a typical 128Mb, PC133 SDRAM, the relevant minimum * parameters from the datasheet are: * Tclk = 7.5ns (CL = 2) * Trp = 15ns * Trc = 60ns * Trcd = 15ns * Trfc = 66ns * * If we are operating the 405GP with the MemClk output frequency set to 100 MHZ, the clock * period is 10ns and the parameters needed for the Timing Register are: * CASL = CL = 2 clock cycles * PTA = Trp = 15ns / 10ns = 2 clock cycles * CTP = Trc - Trcd - Trp = (60ns - 15ns - 15ns) / 10ns= 3 clock cycles * LDF = 2 clock cycles (but can be extended to meet board-level timing) * RFTA = Trfc = 66ns / 10ns= 7 clock cycles * RCD = Trcd = 15ns / 10ns= 2 clock cycles * * The actual bit settings in the register would be: * * CASL = 0b01 * PTA = 0b01 * CTP = 0b10 * LDF = 0b01 * RFTA = 0b011 * RCD = 0b01 * * If Trfc is not specified in the datasheet for PC100 or PC133 memory, set RFTA = Trc * instead. Figure 24 in the PC SDRAM Specification Rev. 1.7 shows refresh to active delay * defined as Trc rather than Trfc. * When using DIMM modules, most but not all of the required timing parameters can be read * from the Serial Presence Detect (SPD) EEPROM on the module. Specifically, Trc and Trfc * are not available from the EEPROM */ #include #include "mip405.h" #include #include <4xx_i2c.h> #include #include "../common/common_util.h" #include #include DECLARE_GLOBAL_DATA_PTR; extern block_dev_desc_t * scsi_get_dev(int dev); extern block_dev_desc_t * ide_get_dev(int dev); #undef SDRAM_DEBUG #define ENABLE_ECC /* for ecc boards */ #define FALSE 0 #define TRUE 1 /* stdlib.h causes some compatibility problems; should fixe these! -- wd */ #ifndef __ldiv_t_defined typedef struct { long int quot; /* Quotient */ long int rem; /* Remainder */ } ldiv_t; extern ldiv_t ldiv (long int __numer, long int __denom); # define __ldiv_t_defined 1 #endif #define PLD_PART_REG PER_PLD_ADDR + 0 #define PLD_VERS_REG PER_PLD_ADDR + 1 #define PLD_BOARD_CFG_REG PER_PLD_ADDR + 2 #define PLD_IRQ_REG PER_PLD_ADDR + 3 #define PLD_COM_MODE_REG PER_PLD_ADDR + 4 #define PLD_EXT_CONF_REG PER_PLD_ADDR + 5 #define MEGA_BYTE (1024*1024) typedef struct { unsigned char boardtype; /* Board revision and Population Options */ unsigned char cal; /* cas Latency (will be programmend as cal-1) */ unsigned char trp; /* datain27 in clocks */ unsigned char trcd; /* datain29 in clocks */ unsigned char tras; /* datain30 in clocks */ unsigned char tctp; /* tras - trcd in clocks */ unsigned char am; /* Address Mod (will be programmed as am-1) */ unsigned char sz; /* log binary => Size = (4MByte<baudrate = 9600; serial_init (); #endif serial_puts ("\n"); serial_puts (s); serial_puts ("\n enable SDRAM_DEBUG for more info\n"); for (;;); } unsigned char get_board_revcfg (void) { out8 (PER_BOARD_ADDR, 0); return (in8 (PER_BOARD_ADDR)); } #ifdef SDRAM_DEBUG void write_hex (unsigned char i) { char cc; cc = i >> 4; cc &= 0xf; if (cc > 9) serial_putc (cc + 55); else serial_putc (cc + 48); cc = i & 0xf; if (cc > 9) serial_putc (cc + 55); else serial_putc (cc + 48); } void write_4hex (unsigned long val) { write_hex ((unsigned char) (val >> 24)); write_hex ((unsigned char) (val >> 16)); write_hex ((unsigned char) (val >> 8)); write_hex ((unsigned char) val); } #endif int init_sdram (void) { unsigned long tmp, baseaddr; unsigned short i; unsigned char trp_clocks, trcd_clocks, tras_clocks, trc_clocks, tctp_clocks; unsigned char cal_val; unsigned char bc; unsigned long sdram_tim, sdram_bank; /*i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);*/ (void) get_clocks (); gd->baudrate = 9600; serial_init (); /* set up the pld */ mtdcr (ebccfga, pb7ap); mtdcr (ebccfgd, PLD_AP); mtdcr (ebccfga, pb7cr); mtdcr (ebccfgd, PLD_CR); /* THIS IS OBSOLETE */ /* set up the board rev reg*/ mtdcr (ebccfga, pb5ap); mtdcr (ebccfgd, BOARD_AP); mtdcr (ebccfga, pb5cr); mtdcr (ebccfgd, BOARD_CR); #ifdef SDRAM_DEBUG /* get all informations from PLD */ serial_puts ("\nPLD Part 0x"); bc = in8 (PLD_PART_REG); write_hex (bc); serial_puts ("\nPLD Vers 0x"); bc = in8 (PLD_VERS_REG); write_hex (bc); serial_puts ("\nBoard Rev 0x"); bc = in8 (PLD_BOARD_CFG_REG); write_hex (bc); serial_puts ("\n"); #endif /* check board */ bc = in8 (PLD_PART_REG); #if defined(CONFIG_MIP405T) if((bc & 0x80)==0) SDRAM_err ("U-Boot configured for a MIP405T not for a MIP405!!!\n"); #else if((bc & 0x80)==0x80) SDRAM_err ("U-Boot configured for a MIP405 not for a MIP405T!!!\n"); #endif /* set-up the chipselect machine */ mtdcr (ebccfga, pb0cr); /* get cs0 config reg */ tmp = mfdcr (ebccfgd); if ((tmp & 0x00002000) == 0) { /* MPS Boot, set up the flash */ mtdcr (ebccfga, pb1ap); mtdcr (ebccfgd, FLASH_AP); mtdcr (ebccfga, pb1cr); mtdcr (ebccfgd, FLASH_CR); } else { /* Flash boot, set up the MPS */ mtdcr (ebccfga, pb1ap); mtdcr (ebccfgd, MPS_AP); mtdcr (ebccfga, pb1cr); mtdcr (ebccfgd, MPS_CR); } /* set up UART0 (CS2) and UART1 (CS3) */ mtdcr (ebccfga, pb2ap); mtdcr (ebccfgd, UART0_AP); mtdcr (ebccfga, pb2cr); mtdcr (ebccfgd, UART0_CR); mtdcr (ebccfga, pb3ap); mtdcr (ebccfgd, UART1_AP); mtdcr (ebccfga, pb3cr); mtdcr (ebccfgd, UART1_CR); bc = in8 (PLD_BOARD_CFG_REG); #ifdef SDRAM_DEBUG serial_puts ("\nstart SDRAM Setup\n"); serial_puts ("\nBoard Rev: "); write_hex (bc); serial_puts ("\n"); #endif i = 0; baseaddr = CFG_SDRAM_BASE; while (sdram_table[i].sz != 0xff) { if (sdram_table[i].boardtype == bc) break; i++; } if (sdram_table[i].boardtype != bc) SDRAM_err ("No SDRAM table found for this board!!!\n"); #ifdef SDRAM_DEBUG serial_puts (" found table "); write_hex (i); serial_puts (" \n"); #endif /* since the ECC initialisation needs some time, * we show that we're alive */ if (sdram_table[i].ecc) serial_puts ("\nInitializing SDRAM, Please stand by"); cal_val = sdram_table[i].cal - 1; /* Cas Latency */ trp_clocks = sdram_table[i].trp; /* 20ns / 7.5 ns datain[27] */ trcd_clocks = sdram_table[i].trcd; /* 20ns /7.5 ns (datain[29]) */ tras_clocks = sdram_table[i].tras; /* 44ns /7.5 ns (datain[30]) */ /* ctp = ((trp + tras) - trp - trcd) => tras - trcd */ tctp_clocks = sdram_table[i].tctp; /* 44 - 20ns = 24ns */ /* trc_clocks is sum of trp_clocks + tras_clocks */ trc_clocks = trp_clocks + tras_clocks; /* get SDRAM timing register */ mtdcr (memcfga, mem_sdtr1); sdram_tim = mfdcr (memcfgd) & ~0x018FC01F; /* insert CASL value */ sdram_tim |= ((unsigned long) (cal_val)) << 23; /* insert PTA value */ sdram_tim |= ((unsigned long) (trp_clocks - 1)) << 18; /* insert CTP value */ sdram_tim |= ((unsigned long) (trc_clocks - trp_clocks - trcd_clocks)) << 16; /* insert LDF (always 01) */ sdram_tim |= ((unsigned long) 0x01) << 14; /* insert RFTA value */ sdram_tim |= ((unsigned long) (trc_clocks - 4)) << 2; /* insert RCD value */ sdram_tim |= ((unsigned long) (trcd_clocks - 1)) << 0; tmp = ((unsigned long) (sdram_table[i].am - 1) << 13); /* AM = 3 */ /* insert SZ value; */ tmp |= ((unsigned long) sdram_table[i].sz << 17); /* get SDRAM bank 0 register */ mtdcr (memcfga, mem_mb0cf); sdram_bank = mfdcr (memcfgd) & ~0xFFCEE001; sdram_bank |= (baseaddr | tmp | 0x01); #ifdef SDRAM_DEBUG serial_puts ("sdtr: "); write_4hex (sdram_tim); serial_puts ("\n"); #endif /* write SDRAM timing register */ mtdcr (memcfga, mem_sdtr1); mtdcr (memcfgd, sdram_tim); #ifdef SDRAM_DEBUG serial_puts ("mb0cf: "); write_4hex (sdram_bank); serial_puts ("\n"); #endif /* write SDRAM bank 0 register */ mtdcr (memcfga, mem_mb0cf); mtdcr (memcfgd, sdram_bank); if (get_bus_freq (tmp) > 110000000) { /* > 110MHz */ /* get SDRAM refresh interval register */ mtdcr (memcfga, mem_rtr); tmp = mfdcr (memcfgd) & ~0x3FF80000; tmp |= 0x07F00000; } else { /* get SDRAM refresh interval register */ mtdcr (memcfga, mem_rtr); tmp = mfdcr (memcfgd) & ~0x3FF80000; tmp |= 0x05F00000; } /* write SDRAM refresh interval register */ mtdcr (memcfga, mem_rtr); mtdcr (memcfgd, tmp); /* enable ECC if used */ #if defined(ENABLE_ECC) && !defined(CONFIG_BOOT_PCI) if (sdram_table[i].ecc) { /* disable checking for all banks */ unsigned long *p; #ifdef SDRAM_DEBUG serial_puts ("disable ECC.. "); #endif mtdcr (memcfga, mem_ecccf); tmp = mfdcr (memcfgd); tmp &= 0xff0fffff; /* disable all banks */ mtdcr (memcfga, mem_ecccf); /* set up SDRAM Controller with ECC enabled */ #ifdef SDRAM_DEBUG serial_puts ("setup SDRAM Controller.. "); #endif mtdcr (memcfgd, tmp); mtdcr (memcfga, mem_mcopt1); tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x90800000; mtdcr (memcfga, mem_mcopt1); mtdcr (memcfgd, tmp); udelay (600); #ifdef SDRAM_DEBUG serial_puts ("fill the memory..\n"); #endif serial_puts ("."); /* now, fill all the memory */ tmp = ((4 * MEGA_BYTE) << sdram_table[i].sz); p = (unsigned long) 0; while ((unsigned long) p < tmp) { *p++ = 0L; if (!((unsigned long) p % 0x00800000)) /* every 8MByte */ serial_puts ("."); } /* enable bank 0 */ serial_puts ("."); #ifdef SDRAM_DEBUG serial_puts ("enable ECC\n"); #endif udelay (400); mtdcr (memcfga, mem_ecccf); tmp = mfdcr (memcfgd); tmp |= 0x00800000; /* enable bank 0 */ mtdcr (memcfgd, tmp); udelay (400); } else #endif { /* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */ mtdcr (memcfga, mem_mcopt1); tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x80C00000; mtdcr (memcfga, mem_mcopt1); mtdcr (memcfgd, tmp); udelay (400); } serial_puts ("\n"); return (0); } int board_early_init_f (void) { init_sdram (); /*-------------------------------------------------------------------------+ | Interrupt controller setup for the PIP405 board. | Note: IRQ 0-15 405GP internally generated; active high; level sensitive | IRQ 16 405GP internally generated; active low; level sensitive | IRQ 17-24 RESERVED | IRQ 25 (EXT IRQ 0) SouthBridge; active low; level sensitive | IRQ 26 (EXT IRQ 1) NMI: active low; level sensitive | IRQ 27 (EXT IRQ 2) SMI: active Low; level sensitive | IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive | IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive | IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive | IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive | Note for MIP405 board: | An interrupt taken for the SouthBridge (IRQ 25) indicates that | the Interrupt Controller in the South Bridge has caused the | interrupt. The IC must be read to determine which device | caused the interrupt. | +-------------------------------------------------------------------------*/ mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */ mtdcr (uicer, 0x00000000); /* disable all ints */ mtdcr (uiccr, 0x00000000); /* set all to be non-critical (for now) */ mtdcr (uicpr, 0xFFFFFF80); /* set int polarities */ mtdcr (uictr, 0x10000000); /* set int trigger levels */ mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */ mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */ return 0; } /* * Get some PLD Registers */ unsigned short get_pld_parvers (void) { unsigned short result; unsigned char rc; rc = in8 (PLD_PART_REG); result = (unsigned short) rc << 8; rc = in8 (PLD_VERS_REG); result |= rc; return result; } void user_led0 (unsigned char on) { if (on) out8 (PLD_COM_MODE_REG, (in8 (PLD_COM_MODE_REG) | 0x4)); else out8 (PLD_COM_MODE_REG, (in8 (PLD_COM_MODE_REG) & 0xfb)); } void ide_set_reset (int idereset) { /* if reset = 1 IDE reset will be asserted */ if (idereset) out8 (PLD_COM_MODE_REG, (in8 (PLD_COM_MODE_REG) | 0x1)); else { udelay (10000); out8 (PLD_COM_MODE_REG, (in8 (PLD_COM_MODE_REG) & 0xfe)); } } /* ------------------------------------------------------------------------- */ void get_pcbrev_var(unsigned char *pcbrev, unsigned char *var) { #if !defined(CONFIG_MIP405T) unsigned char bc,rc,tmp; int i; bc = in8 (PLD_BOARD_CFG_REG); tmp = ~bc; tmp &= 0xf; rc = 0; for (i = 0; i < 4; i++) { rc <<= 1; rc += (tmp & 0x1); tmp >>= 1; } rc++; if(( (((bc>>4) & 0xf)==0x2) /* Rev C PCB or */ || (((bc>>4) & 0xf)==0x1)) /* Rev B PCB with */ && (rc==0x1)) /* Population Option 1 is a -3 */ rc=3; *pcbrev=(bc >> 4) & 0xf; *var=rc; #else unsigned char bc; bc = in8 (PLD_BOARD_CFG_REG); *pcbrev=(bc >> 4) & 0xf; *var=16-(bc & 0xf); #endif } /* * Check Board Identity: */ /* serial String: "MIP405_1000" OR "MIP405T_1000" */ #if !defined(CONFIG_MIP405T) #define BOARD_NAME "MIP405" #else #define BOARD_NAME "MIP405T" #endif int checkboard (void) { char s[50]; unsigned char bc, var; int i; backup_t *b = (backup_t *) s; puts ("Board: "); get_pcbrev_var(&bc,&var); i = getenv_r ("serial#", (char *)s, 32); if ((i == 0) || strncmp ((char *)s, BOARD_NAME,sizeof(BOARD_NAME))) { get_backup_values (b); if (strncmp (b->signature, "MPL\0", 4) != 0) { puts ("### No HW ID - assuming " BOARD_NAME); printf ("-%d Rev %c", var, 'A' + bc); } else { b->serial_name[sizeof(BOARD_NAME)-1] = 0; printf ("%s-%d Rev %c SN: %s", b->serial_name, var, 'A' + bc, &b->serial_name[sizeof(BOARD_NAME)]); } } else { s[sizeof(BOARD_NAME)-1] = 0; printf ("%s-%d Rev %c SN: %s", s, var,'A' + bc, &s[sizeof(BOARD_NAME)]); } bc = in8 (PLD_EXT_CONF_REG); printf (" Boot Config: 0x%x\n", bc); return (0); } /* ------------------------------------------------------------------------- */ /* ------------------------------------------------------------------------- */ /* initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of the necessary info for SDRAM controller configuration */ /* ------------------------------------------------------------------------- */ /* ------------------------------------------------------------------------- */ static int test_dram (unsigned long ramsize); long int initdram (int board_type) { unsigned long bank_reg[4], tmp, bank_size; int i, ds; unsigned long TotalSize; ds = 0; /* since the DRAM controller is allready set up, calculate the size with the bank registers */ mtdcr (memcfga, mem_mb0cf); bank_reg[0] = mfdcr (memcfgd); mtdcr (memcfga, mem_mb1cf); bank_reg[1] = mfdcr (memcfgd); mtdcr (memcfga, mem_mb2cf); bank_reg[2] = mfdcr (memcfgd); mtdcr (memcfga, mem_mb3cf); bank_reg[3] = mfdcr (memcfgd); TotalSize = 0; for (i = 0; i < 4; i++) { if ((bank_reg[i] & 0x1) == 0x1) { tmp = (bank_reg[i] >> 17) & 0x7; bank_size = 4 << tmp; TotalSize += bank_size; } else ds = 1; } mtdcr (memcfga, mem_ecccf); tmp = mfdcr (memcfgd); if (!tmp) printf ("No "); printf ("ECC "); test_dram (TotalSize * MEGA_BYTE); return (TotalSize * MEGA_BYTE); } /* ------------------------------------------------------------------------- */ static int test_dram (unsigned long ramsize) { #ifdef SDRAM_DEBUG mem_test (0L, ramsize, 1); #endif /* not yet implemented */ return (1); } /* used to check if the time in RTC is valid */ static unsigned long start; static struct rtc_time tm; extern flash_info_t flash_info[]; /* info for FLASH chips */ int misc_init_r (void) { /* adjust flash start and size as well as the offset */ gd->bd->bi_flashstart=0-flash_info[0].size; gd->bd->bi_flashsize=flash_info[0].size-CFG_MONITOR_LEN; gd->bd->bi_flashoffset=0; /* check, if RTC is running */ rtc_get (&tm); start=get_timer(0); /* if MIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */ if (mfdcr(strap) & PSR_ROM_LOC) mtspr(ccr0, (mfspr(ccr0) & ~0x80)); return (0); } void print_mip405_rev (void) { unsigned char part, vers, pcbrev, var; get_pcbrev_var(&pcbrev,&var); part = in8 (PLD_PART_REG); vers = in8 (PLD_VERS_REG); printf ("Rev: " BOARD_NAME "-%d Rev %c PLD %d Vers %d\n", var, pcbrev + 'A', part & 0x7F, vers); } #ifdef CONFIG_POST /* * Returns 1 if keys pressed to start the power-on long-running tests * Called from board_init_f(). */ int post_hotkeys_pressed(void) { return 0; /* No hotkeys supported */ } #endif extern void mem_test_reloc(void); extern int mk_date (char *, struct rtc_time *); int last_stage_init (void) { unsigned long stop; struct rtc_time newtm; char *s; mem_test_reloc(); /* write correct LED configuration */ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x14, 0x2402) != 0) { printf ("Error writing to the PHY\n"); } /* since LED/CFG2 is not connected on the -2, * write to correct capability information */ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x4, 0x01E1) != 0) { printf ("Error writing to the PHY\n"); } print_mip405_rev (); show_stdio_dev (); check_env (); /* check if RTC time is valid */ stop=get_timer(start); while(stop<1200) { /* we wait 1.2 sec to check if the RTC is running */ udelay(1000); stop=get_timer(start); } rtc_get (&newtm); if(tm.tm_sec==newtm.tm_sec) { s=getenv("defaultdate"); if(!s) mk_date ("010112001970", &newtm); else if(mk_date (s, &newtm)!=0) { printf("RTC: Bad date format in defaultdate\n"); return 0; } rtc_reset (); rtc_set(&newtm); } return 0; } /*************************************************************************** * some helping routines */ int overwrite_console (void) { return ((in8 (PLD_EXT_CONF_REG) & 0x1)==0); /* return TRUE if console should be overwritten */ } /************************************************************************ * Print MIP405 Info ************************************************************************/ void print_mip405_info (void) { unsigned char part, vers, cfg, irq_reg, com_mode, ext; part = in8 (PLD_PART_REG); vers = in8 (PLD_VERS_REG); cfg = in8 (PLD_BOARD_CFG_REG); irq_reg = in8 (PLD_IRQ_REG); com_mode = in8 (PLD_COM_MODE_REG); ext = in8 (PLD_EXT_CONF_REG); printf ("PLD Part %d version %d\n", part & 0x7F, vers); printf ("Board Revision %c\n", ((cfg >> 4) & 0xf) + 'A'); printf ("Population Options %d %d %d %d\n", (cfg) & 0x1, (cfg >> 1) & 0x1, (cfg >> 2) & 0x1, (cfg >> 3) & 0x1); printf ("User LED %s\n", (com_mode & 0x4) ? "on" : "off"); printf ("UART Clocks %d\n", (com_mode >> 4) & 0x3); #if !defined(CONFIG_MIP405T) printf ("User Config Switch %d %d %d %d %d %d %d %d\n", (ext) & 0x1, (ext >> 1) & 0x1, (ext >> 2) & 0x1, (ext >> 3) & 0x1, (ext >> 4) & 0x1, (ext >> 5) & 0x1, (ext >> 6) & 0x1, (ext >> 7) & 0x1); printf ("SER1 uses handshakes %s\n", (ext & 0x80) ? "DTR/DSR" : "RTS/CTS"); #else printf ("User Config Switch %d %d %d %d %d %d %d %d\n", (ext) & 0x1, (ext >> 1) & 0x1, (ext >> 2) & 0x1, (ext >> 3) & 0x1, (ext >> 4) & 0x1, (ext >> 5) & 0x1, (ext >> 6) & 0x1,(ext >> 7) & 0x1); #endif printf ("IDE Reset %s\n", (ext & 0x01) ? "asserted" : "not asserted"); printf ("IRQs:\n"); printf (" PIIX INTR: %s\n", (irq_reg & 0x80) ? "inactive" : "active"); #if !defined(CONFIG_MIP405T) printf (" UART0 IRQ: %s\n", (irq_reg & 0x40) ? "inactive" : "active"); printf (" UART1 IRQ: %s\n", (irq_reg & 0x20) ? "inactive" : "active"); #endif printf (" PIIX SMI: %s\n", (irq_reg & 0x10) ? "inactive" : "active"); printf (" PIIX INIT: %s\n", (irq_reg & 0x8) ? "inactive" : "active"); printf (" PIIX NMI: %s\n", (irq_reg & 0x4) ? "inactive" : "active"); }