From 6bde1ec10ff438170721624ca87b86fd25669b3b Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Wed, 6 Aug 2014 12:59:54 +0900 Subject: powerpc: mpc8xx: remove GEN860T, GEN806T_SC board support These boards have been orphaned for a while and old enough. Signed-off-by: Masahiro Yamada --- include/commproc.h | 21 -- include/configs/GEN860T.h | 712 ---------------------------------------------- include/status_led.h | 24 -- 3 files changed, 757 deletions(-) delete mode 100644 include/configs/GEN860T.h (limited to 'include') diff --git a/include/commproc.h b/include/commproc.h index 7605713..76a62de 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -556,27 +556,6 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00002600) #endif /* CONFIG_FPS850L, CONFIG_FPS860L */ -/*** GEN860T **********************************************************/ -#if defined(CONFIG_GEN860T) -#undef SCC_ENET -#define FEC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */ -#endif /* CONFIG_GEN860T */ - /*** HERMES-PRO ******************************************************/ /* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */ diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h deleted file mode 100644 index fd6c976..0000000 --- a/include/configs/GEN860T.h +++ /dev/null @@ -1,712 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * Keith Outwater, keith_outwater@mvis.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config_GEN860T.h - board specific configuration options - */ - -#ifndef __CONFIG_GEN860T_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_MPC860 -#define CONFIG_GEN860T - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -/* - * Identify the board - */ -#if !defined(CONFIG_SC) -#define CONFIG_IDENT_STRING " B2" -#else -#define CONFIG_IDENT_STRING " SC" -#endif - -/* - * Don't depend on the RTC clock to determine clock frequency - - * the 860's internal rtc uses a 32.768 KHz clock which is - * generated by the DS1337 - and the DS1337 clock can be turned off. - */ -#if !defined(CONFIG_SC) -#define CONFIG_8xx_GCLK_FREQ 66600000 -#else -#define CONFIG_8xx_GCLK_FREQ 48000000 -#endif - -/* - * The RS-232 console port is on SMC1 - */ -#define CONFIG_8xx_CONS_SMC1 -#define CONFIG_BAUDRATE 38400 - -/* - * Print console information - */ -#undef CONFIG_SYS_CONSOLE_INFO_QUIET - -/* - * Set the autoboot delay in seconds. A delay of -1 disables autoboot - */ -#define CONFIG_BOOTDELAY 5 - -/* - * Pass the clock frequency to the Linux kernel in units of MHz - */ -#define CONFIG_CLOCKS_IN_MHZ - -#define CONFIG_PREBOOT \ - "echo;echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" - -/* - * Turn off echo for serial download by default. Allow baud rate to be changed - * for downloads - */ -#undef CONFIG_LOADS_ECHO -#define CONFIG_SYS_LOADS_BAUD_CHANGE - -/* - * Turn off the watchdog timer - */ -#undef CONFIG_WATCHDOG - -/* - * Do not reboot if a panic occurs - */ -#define CONFIG_PANIC_HANG - -/* - * Enable the status LED - */ -#define CONFIG_STATUS_LED - -/* - * Reset address. We pick an address such that when an instruction - * is executed at that address, a machine check exception occurs - */ -#define CONFIG_SYS_RESET_ADDRESS ((ulong) -1) - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * The GEN860T network interface uses the on-chip 10/100 FEC with - * an Intel LXT971A PHY connected to the 860T's MII. The PHY's - * MII address is hardwired on the board to zero. - */ -#define CONFIG_FEC_ENET -#define CONFIG_SYS_DISCOVER_PHY -#define CONFIG_MII -#define CONFIG_MII_INIT 1 -#define CONFIG_PHY_ADDR 0 - -/* - * Set default IP stuff just to get bootstrap entries into the - * environment so that we can source the full default environment. - */ -#define CONFIG_ETHADDR 9a:52:63:15:85:25 -#define CONFIG_SERVERIP 10.0.4.201 -#define CONFIG_IPADDR 10.0.4.111 - -/* - * This board has a 32 kibibyte EEPROM (Atmel AT24C256) connected to - * the MPC860T I2C interface. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10 mS w/ 20% margin */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* need 16 bit address */ -#define CONFIG_ENV_EEPROM_SIZE (32 * 1024) - -/* - * Enable I2C and select the hardware/software driver - */ -#define CONFIG_HARD_I2C 1 /* CPM based I2C */ -#undef CONFIG_SYS_I2C_SOFT /* Bit-banged I2C */ - -#ifdef CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 /* clock speed in Hz */ -#define CONFIG_SYS_I2C_SLAVE 0xFE /* I2C slave address */ -#endif - -#ifdef CONFIG_SYS_I2C_SOFT -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT_SPEED 50000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if (bit) \ - immr->im_cpm.cp_pbdat |= PB_SDA; \ - else \ - immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if (bit) \ - immr->im_cpm.cp_pbdat |= PB_SCL; \ - else \ - immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif - -/* - * Allow environment overwrites by anyone - */ -#define CONFIG_ENV_OVERWRITE - -#if !defined(CONFIG_SC) -/* - * The MPC860's internal RTC is horribly broken in rev D masks. Three - * internal MPC860T circuit nodes were inadvertently left floating; this - * causes KAPWR current in power down mode to be three orders of magnitude - * higher than specified in the datasheet (from 10 uA to 10 mA). No - * reasonable battery can keep that kind RTC running during powerdown for any - * length of time, so we use an external RTC on the I2C bus instead. - */ -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -#else -/* - * No external RTC on SC variant, so we're stuck with the internal one. - */ -#define CONFIG_RTC_MPC8xx -#endif - -/* - * Power On Self Test support - */ -#define CONFIG_POST ( CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_SPR ) - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_DATE -#define CONFIG_CMD_FPGA -#define CONFIG_CMD_FPGA_LOADMK -#define CONFIG_CMD_MII -#define CONFIG_CMD_BEDBUG - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - -/* - * There is no IDE/PCMCIA hardware support on the board. - */ -#undef CONFIG_IDE_PCMCIA -#undef CONFIG_IDE_LED -#undef CONFIG_IDE_RESET - -/* - * Enable the call to misc_init_r() for miscellaneous platform - * dependent initialization. - */ -#define CONFIG_MISC_INIT_R - -/* - * Enable call to last_stage_init() so we can twiddle some LEDS :) - */ -#define CONFIG_LAST_STAGE_INIT - -/* - * Virtex2 FPGA configuration support - */ -#define CONFIG_FPGA_COUNT 1 -#define CONFIG_FPGA -#define CONFIG_FPGA_XILINX -#define CONFIG_FPGA_VIRTEX2 -#define CONFIG_SYS_FPGA_PROG_FEEDBACK - -/* - * Verbose help from command monitor. - */ -#define CONFIG_SYS_LONGHELP -#if !defined(CONFIG_SC) -#define CONFIG_SYS_PROMPT "B2> " -#else -#define CONFIG_SYS_PROMPT "SC> " -#endif - - -/* - * Use the "hush" command parser - */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Set buffer size for console I/O - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 -#else -#define CONFIG_SYS_CBSIZE 256 -#endif - -/* - * Print buffer size - */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - -/* - * Maximum number of arguments that a command can accept - */ -#define CONFIG_SYS_MAXARGS 16 - -/* - * Boot argument buffer size - */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * Default memory test range - */ -#define CONFIG_SYS_MEMTEST_START 0x0100000 -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (128 * 1024)) - -/* - * Select the more full-featured memory test - */ -#define CONFIG_SYS_ALT_MEMTEST - -/* - * Default load address - */ -#define CONFIG_SYS_LOAD_ADDR 0x01000000 - -/* - * Device memory map (after SDRAM remap to 0x0): - * - * CS Device Base Addr Size - * ---------------------------------------------------- - * CS0* Flash 0x40000000 64 M - * CS1* SDRAM 0x00000000 16 M - * CS2* Disk-On-Chip 0x50000000 32 K - * CS3* FPGA 0x60000000 64 M - * CS4* SelectMap 0x70000000 32 K - * CS5* Mil-Std 1553 I/F 0x80000000 32 K - * CS6* Unused - * CS7* Unused - * IMMR 860T Registers 0xfff00000 - */ - -/* - * Base addresses and block sizes - */ -#define CONFIG_SYS_IMMR 0xFF000000 - -#define SDRAM_BASE 0x00000000 -#define SDRAM_SIZE (64 * 1024 * 1024) - -#define FLASH_BASE 0x40000000 -#define FLASH_SIZE (16 * 1024 * 1024) - -#define DOC_BASE 0x50000000 -#define DOC_SIZE (32 * 1024) - -#define FPGA_BASE 0x60000000 -#define FPGA_SIZE (64 * 1024 * 1024) - -#define SELECTMAP_BASE 0x70000000 -#define SELECTMAP_SIZE (32 * 1024) - -#define M1553_BASE 0x80000000 -#define M1553_SIZE (64 * 1024) - -/* - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_INIT_DATA_SIZE 64 /* # bytes reserved for initial data*/ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE SDRAM_BASE - -/* - * FLASH organization - */ -#define CONFIG_SYS_FLASH_BASE FLASH_BASE -#define CONFIG_SYS_FLASH_SIZE FLASH_SIZE -#define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024) -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 128 - -/* - * The timeout values are for an entire chip and are in milliseconds. - * Yes I know that the write timeout is huge. Accroding to the - * datasheet a single byte takes 630 uS (round to 1 ms) max at worst - * case VCC and temp after 100K programming cycles. It works out - * to 280 minutes (might as well be forever). - */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (CONFIG_SYS_MAX_FLASH_SECT * 5000) -#define CONFIG_SYS_FLASH_WRITE_TOUT (CONFIG_SYS_MAX_FLASH_SECT * 128 * 1024 * 1) - -/* - * Allow direct writes to FLASH from tftp transfers (** dangerous **) - */ -#define CONFIG_SYS_DIRECT_FLASH_TFTP - -/* - * Reserve memory for U-Boot. - */ -#define CONFIG_SYS_MAX_UBOOT_SECTS 4 -#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_MAX_UBOOT_SECTS * CONFIG_SYS_FLASH_SECT_SIZE) -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE - -/* - * Select environment placement. NOTE that u-boot.lds must - * be edited if this is changed! - */ -#undef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_IS_IN_EEPROM - -#if defined(CONFIG_ENV_IS_IN_EEPROM) -#define CONFIG_ENV_SIZE (2 * 1024) -#define CONFIG_ENV_OFFSET (CONFIG_ENV_EEPROM_SIZE - (8 * 1024)) -#else -#define CONFIG_ENV_SIZE 0x1000 -#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SIZE - -/* - * This ultimately gets passed right into the linker script, so we have to - * use a number :( - */ -#define CONFIG_ENV_OFFSET 0x060000 -#endif - -/* - * Reserve memory for malloc() - */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) - -/* - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of above value */ -#endif - -/*------------------------------------------------------------------------ - * SYPCR - System Protection Control UM 11-9 - * ----------------------------------------------------------------------- - * SYPCR can only be written once after reset! - * - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR ( SYPCR_SWTC | \ - SYPCR_BMT | \ - SYPCR_BME | \ - SYPCR_SWF | \ - SYPCR_SWE | \ - SYPCR_SWRI | \ - SYPCR_SWP \ - ) -#else -#define CONFIG_SYS_SYPCR ( SYPCR_SWTC | \ - SYPCR_BMT | \ - SYPCR_BME | \ - SYPCR_SWF | \ - SYPCR_SWP \ - ) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration UM 11-6 - *----------------------------------------------------------------------- - * Set debug pin mux, enable SPKROUT and GPLB5*. - */ -#define CONFIG_SYS_SIUMCR ( SIUMCR_DBGC11 | \ - SIUMCR_DBPC11 | \ - SIUMCR_MLRC11 | \ - SIUMCR_GB5E \ - ) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control UM 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freeze enabled - */ -#define CONFIG_SYS_TBSCR ( TBSCR_REFA | \ - TBSCR_REFB | \ - TBSCR_TBF \ - ) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register UM 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC ( RTCSC_SEC | \ - RTCSC_ALR | \ - RTCSC_RTF | \ - RTCSC_RTE \ - ) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control UM 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR ( PISCR_PS | \ - PISCR_PITF \ - ) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register UM 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit. Set MF for 1:2:1 mode. - */ -#define CONFIG_SYS_PLPRCR ( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK) | \ - PLPRCR_SPLSS | \ - PLPRCR_TEXPS | \ - PLPRCR_TMIST \ - ) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register UM 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 - -#if !defined(CONFIG_SC) -#define CONFIG_SYS_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ - SCCR_COM00 | /* full strength CLKOUT */ \ - SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \ - SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \ - SCCR_DFNL000 | \ - SCCR_DFNH000 \ - ) -#else -#define CONFIG_SYS_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ - SCCR_COM00 | /* full strength CLKOUT */ \ - SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \ - SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \ - SCCR_DFNL000 | \ - SCCR_DFNH000 | \ - SCCR_RTDIV | \ - SCCR_RTSEL \ - ) -#endif - -/*----------------------------------------------------------------------- - * DER - Debug Enable Register UM 37-46 - *----------------------------------------------------------------------- - * Mask all events that can cause entry into debug mode - */ -#define CONFIG_SYS_DER 0 - -/* - * Initialize Memory Controller: - * - * BR0 and OR0 (FLASH memory) - */ -#define FLASH_BASE0_PRELIM FLASH_BASE - -/* - * Flash address mask - */ -#define CONFIG_SYS_PRELIM_OR_AM 0xfe000000 - -/* - * FLASH timing: - * 33 Mhz bus with ACS = 11, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 - */ -#define CONFIG_SYS_OR_TIMING_FLASH ( OR_CSNT_SAM | \ - OR_ACS_DIV2 | \ - OR_BI | \ - OR_SCY_2_CLK | \ - OR_TRLX | \ - OR_EHTR \ - ) - -#define CONFIG_SYS_OR0_PRELIM ( CONFIG_SYS_PRELIM_OR_AM | \ - CONFIG_SYS_OR_TIMING_FLASH \ - ) - -#define CONFIG_SYS_BR0_PRELIM ( (FLASH_BASE0_PRELIM & BR_BA_MSK) | \ - BR_MS_GPCM | \ - BR_PS_8 | \ - BR_V \ - ) - -/* - * SDRAM configuration - */ -#define CONFIG_SYS_OR1_AM 0xfc000000 -#define CONFIG_SYS_OR1 ( (CONFIG_SYS_OR1_AM & OR_AM_MSK) | \ - OR_CSNT_SAM \ - ) - -#define CONFIG_SYS_BR1 ( (SDRAM_BASE & BR_BA_MSK) | \ - BR_MS_UPMA | \ - BR_PS_32 | \ - BR_V \ - ) - -/* - * Refresh rate 7.8 us (= 64 ms / 8K = 31.2 uS quad bursts) for one bank - * of 256 MBit SDRAM - */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 - -/* - * Periodic timer for refresh @ 33 MHz system clock - */ -#define CONFIG_SYS_MAMR_PTA 64 - -/* - * MAMR settings for SDRAM - */ -#define CONFIG_SYS_MAMR_8COL ( (CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | \ - MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | \ - MAMR_DSA_1_CYCL | \ - MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | \ - MAMR_WLFA_1X | \ - MAMR_TLFA_4X \ - ) - -/* - * CS2* configuration for Disk On Chip: - * 33 MHz bus with TRLX=1, ACS=11, CSNT=1, EBDF=1, SCY=2, EHTR=1, - * no burst. - */ -#define CONFIG_SYS_OR2_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ - OR_CSNT_SAM | \ - OR_ACS_DIV2 | \ - OR_BI | \ - OR_SCY_2_CLK | \ - OR_TRLX | \ - OR_EHTR \ - ) - -#define CONFIG_SYS_BR2_PRELIM ( (DOC_BASE & BR_BA_MSK) | \ - BR_PS_8 | \ - BR_MS_GPCM | \ - BR_V \ - ) - -/* - * CS3* configuration for FPGA: - * 33 MHz bus with SCY=15, no burst. - * The FPGA uses TA and TEA to terminate bus cycles, but we - * clear SETA and set the cycle length to a large number so that - * the cycle will still complete even if there is a configuration - * error that prevents TA from asserting on FPGA accesss. - */ -#define CONFIG_SYS_OR3_PRELIM ( (0xfc000000 & OR_AM_MSK) | \ - OR_SCY_15_CLK | \ - OR_BI \ - ) - -#define CONFIG_SYS_BR3_PRELIM ( (FPGA_BASE & BR_BA_MSK) | \ - BR_PS_32 | \ - BR_MS_GPCM | \ - BR_V \ - ) -/* - * CS4* configuration for FPGA SelectMap configuration interface. - * 33 MHz bus, UPMB, no burst. Do not assert GPLB5 on falling edge - * of GCLK1_50 - */ -#define CONFIG_SYS_OR4_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ - OR_G5LS | \ - OR_BI \ - ) - -#define CONFIG_SYS_BR4_PRELIM ( (SELECTMAP_BASE & BR_BA_MSK) | \ - BR_PS_8 | \ - BR_MS_UPMB | \ - BR_V \ - ) - -/* - * CS5* configuration for Mil-Std 1553 databus interface. - * 33 MHz bus, GPCM, no burst. - * The 1553 interface uses TA and TEA to terminate bus cycles, - * but we clear SETA and set the cycle length to a large number so that - * the cycle will still complete even if there is a configuration - * error that prevents TA from asserting on FPGA accesss. - */ -#define CONFIG_SYS_OR5_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ - OR_SCY_15_CLK | \ - OR_EHTR | \ - OR_TRLX | \ - OR_CSNT_SAM | \ - OR_BI \ - ) - -#define CONFIG_SYS_BR5_PRELIM ( (M1553_BASE & BR_BA_MSK) | \ - BR_PS_16 | \ - BR_MS_GPCM | \ - BR_V \ - ) - -/* - * FEC interrupt assignment - */ -#define FEC_INTERRUPT SIU_LEVEL1 - -/* - * Sanity checks - */ -#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) -#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured -#endif - -#endif /* __CONFIG_GEN860T_H */ diff --git a/include/status_led.h b/include/status_led.h index c9d21d1..c1d2242 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -56,30 +56,6 @@ void status_led_set (int led, int state); # define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ -/***** GEN860T *********************************************************/ -#elif defined(CONFIG_GEN860T) - -# define STATUS_LED_PAR im_ioport.iop_papar -# define STATUS_LED_DIR im_ioport.iop_padir -# define STATUS_LED_ODR im_ioport.iop_paodr -# define STATUS_LED_DAT im_ioport.iop_padat - -# define STATUS_LED_BIT 0x0800 /* Red LED 0 is on PA.4 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE STATUS_LED_OFF -# define STATUS_LED_BIT1 0x0400 /* Grn LED 1 is on PA.5 */ -# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 8) -# define STATUS_LED_STATE1 STATUS_LED_BLINKING -# define STATUS_LED_BIT2 0x0080 /* Red LED 2 is on PA.8 */ -# define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE2 STATUS_LED_OFF -# define STATUS_LED_BIT3 0x0040 /* Grn LED 3 is on PA.9 */ -# define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE3 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ -# define STATUS_LED_BOOT 1 /* Boot status on LED 1 */ - /***** IVMS8 **********************************************************/ #elif defined(CONFIG_IVMS8) -- cgit v1.1