From 3c5b20f1b7c6687813d193033adddf0f93a3335d Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Mon, 15 Dec 2014 23:26:08 +0900 Subject: mpc8xx: remove ELPT860 board support This board is still a non-generic board. Signed-off-by: Masahiro Yamada Cc: The LEOX team --- include/commproc.h | 26 ---- include/configs/ELPT860.h | 374 ---------------------------------------------- 2 files changed, 400 deletions(-) delete mode 100644 include/configs/ELPT860.h (limited to 'include') diff --git a/include/commproc.h b/include/commproc.h index 3e19603..af67878 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -456,32 +456,6 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00002c00) #endif /* CONFIG_BSEIP */ -/*** ELPT860 *********************************************************/ - -#ifdef CONFIG_ELPT860 -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. - */ -# define PROFF_ENET PROFF_SCC1 -# define CPM_CR_ENET CPM_CR_CH_SCC1 -# define SCC_ENET 0 - -# define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */ -# define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */ -# define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ -# define PA_ENET_TCLK ((ushort)0x0200) /* PA 6 */ - -# define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */ -# define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */ -# define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */ - -/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK1) to - * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. - */ -# define SICR_ENET_MASK ((uint)0x000000FF) -# define SICR_ENET_CLKRT ((uint)0x00000025) -#endif /* CONFIG_ELPT860 */ - /*** ESTEEM 192E **************************************************/ #ifdef CONFIG_ESTEEM192E /* ESTEEM192E diff --git a/include/configs/ELPT860.h b/include/configs/ELPT860.h deleted file mode 100644 index a9d62c8..0000000 --- a/include/configs/ELPT860.h +++ /dev/null @@ -1,374 +0,0 @@ -/* -**===================================================================== -** -** Copyright (C) 2000, 2001, 2002, 2003 -** The LEOX team , http://www.leox.org -** -** LEOX.org is about the development of free hardware and software resources -** for system on chip. -** -** Description: U-Boot port on the LEOX's ELPT860 CPU board -** ~~~~~~~~~~~ -** -**===================================================================== -** - * SPDX-License-Identifier: GPL-2.0+ -** -**===================================================================== -*/ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC860 1 /* It's a MPC860, in fact a 860T CPU */ -#define CONFIG_MPC860T 1 -#define CONFIG_ELPT860 1 /* ...on a LEOX's ELPT860 CPU board */ - -#define CONFIG_SYS_TEXT_BASE 0x02000000 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE - -#define CONFIG_CLOCKS_IN_MHZ 1 /* Clock passed to Linux (<2.4.5) in MHz */ -#define CONFIG_8xx_GCLK_FREQ 50000000 /* MPC860T runs at 50MHz */ - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -/* BOOT arguments */ -#define CONFIG_PREBOOT \ - "echo;" \ - "echo Type \"run nfsboot\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "rootargs=setenv rootpath /tftp/${ipaddr}\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:eth0:off panic=1\0" \ - "ramboot=tftp 400000 /home/paugaml/pMulti;" \ - "run ramargs;bootm\0" \ - "nfsboot=tftp 400000 /home/paugaml/uImage;" \ - "run rootargs;run nfsargs;run addip;bootm\0" \ - "" -#define CONFIG_BOOTCOMMAND "run ramboot" - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ -#undef CONFIG_RTC_MPC8xx /* internal RTC MPC8xx unused */ -#define CONFIG_RTC_DS164x 1 /* RTC is a Dallas DS1646 */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "LEOX_elpt860: " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -/* - * Environment Variables and Storages - */ -#define CONFIG_ENV_OVERWRITE 1 /* Allow Overwrite of serial# & ethaddr */ - -#undef CONFIG_ENV_IS_IN_NVRAM /* Environment is in NVRAM */ -#undef CONFIG_ENV_IS_IN_EEPROM /* Environment is in I2C EEPROM */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment is in FLASH */ - -#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600 bps */ - -#define CONFIG_ETHADDR 00:01:77:00:60:40 -#define CONFIG_IPADDR 192.168.0.30 -#define CONFIG_NETMASK 255.255.255.0 - -#define CONFIG_SERVERIP 192.168.0.1 -#define CONFIG_GATEWAYIP 192.168.0.1 - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x02000000 -#define CONFIG_SYS_NVRAM_BASE 0x03000000 - -#if defined(CONFIG_ENV_IS_IN_FLASH) -# if defined(DEBUG) -# define CONFIG_SYS_MONITOR_LEN (320 << 10) /* Reserve 320 kB for Monitor */ -# else -# define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -# endif -#else -# if defined(DEBUG) -# define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -# else -# define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -# endif -#endif - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#if defined(CONFIG_ENV_IS_IN_FLASH) -# define CONFIG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */ -# define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ -#endif - -/*----------------------------------------------------------------------- - * NVRAM organization - */ -#define CONFIG_SYS_NVRAM_BASE_ADDR CONFIG_SYS_NVRAM_BASE /* Base address of NVRAM area */ -#define CONFIG_SYS_NVRAM_SIZE ((128*1024)-8) /* clock regs resident in the */ - /* 8 top NVRAM locations */ - -#if defined(CONFIG_ENV_IS_IN_NVRAM) -# define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE /* Base address of NVRAM area */ -# define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ -#endif - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -# define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP) -#else -# define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - * Once-per-Second Interrupt, Alarm Interrupt, RTC freezing enabled, RTC - * enabled - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - leave PLL multiplication factor unchanged ! - */ -#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_TBS | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - -/*----------------------------------------------------------------------- - * Chip Selects + SDRAM timings + Memory Periodic Timer Prescaler - *----------------------------------------------------------------------- - * - */ -#ifdef DEBUG -# define CONFIG_SYS_DER 0xFFE7400F /* Debug Enable Register */ -#else -# define CONFIG_SYS_DER 0 -#endif - -/* - * Init Memory Controller: - * ~~~~~~~~~~~~~~~~~~~~~~ - * - * BR0 and OR0 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFF000000 /* 16 MB between each CSx */ - -/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 0, SCY = 8, EHTR = 0 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV2 | OR_BI | OR_SCY_8_CLK) - -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) - -/* - * BR1 and OR1 (SDRAM) - * - */ -#define SDRAM_BASE1_PRELIM CONFIG_SYS_SDRAM_BASE /* SDRAM bank #0 */ -#define SDRAM_MAX_SIZE 0x02000000 /* 32 MB MAX for CS1 */ - -/* SDRAM timing: */ -#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000000 - -#define CONFIG_SYS_OR1_PRELIM ((2 * CONFIG_SYS_PRELIM_OR_AM) | CONFIG_SYS_OR_TIMING_SDRAM ) -#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) - -/* - * BR2 and OR2 (NVRAM) - * - */ -#define NVRAM_BASE1_PRELIM CONFIG_SYS_NVRAM_BASE /* NVRAM bank #0 */ -#define NVRAM_MAX_SIZE 0x00020000 /* 128 KB MAX for CS2 */ - -#define CONFIG_SYS_OR2_PRELIM 0xFFF80160 -#define CONFIG_SYS_BR2_PRELIM ((NVRAM_BASE1_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ - -/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -#endif /* __CONFIG_H */ -- cgit v1.1