From ef11df6b66ecf5797e94ba322254b8fb7a4e2e12 Mon Sep 17 00:00:00 2001
From: John Rigby <jrigby@freescale.com>
Date: Tue, 5 Aug 2008 17:38:57 -0600
Subject: mpc5121: squash some fdt fixup errors

On ADS5121 when booting linux the following errors are seen:
    Unable to update property /soc5121@80000000:bus-frequency, err=FDT_ERR_NOTFOUND
    Unable to update property /soc5121@80000000/ethernet@2800:local-mac-address, err=FDT_ERR_NOTFOUND
    Unable to update property /soc5121@80000000/ethernet@2800:address, err=FDT_ERR_NOTFOUND

This is caused by ft_cpu_setup trying to deal with
both old and new soc node naming.  This patch
fixes this by being smarter about what to
fixup.

Also do soc node fixups by compatible instead of by path.
A new board config called OF_SOC_COMPAT defined
to be "fsl,mpc5121-immr" replaces the old
OF_SOC node path that was defined to be "soc@80000000".

Old device trees still work, but the compatiblity
is conditional on CONFIG_OF_SUPPORT_OLD_DEVICE_TREES
which is on by default in include/configs/ads5121.h.

Signed-off-by: John Rigby <jrigby@freescale.com>
---
 include/configs/ads5121.h | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h
index f104e68..091da80 100644
--- a/include/configs/ads5121.h
+++ b/include/configs/ads5121.h
@@ -308,6 +308,7 @@
 #define CONFIG_PHY_ADDR		0x1
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_FEC_AN_TIMEOUT	1
+#define CONFIG_HAS_ETH0
 
 /*
  * Configure on-board RTC
@@ -478,10 +479,10 @@
 
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES	1
 
 #define OF_CPU			"PowerPC,5121@0"
-#define OF_SOC			"soc@80000000"
-#define OF_SOC_OLD		"soc5121@80000000"
+#define OF_SOC_COMPAT		"fsl,mpc5121-immr"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
 #define OF_STDOUT_PATH		"/soc@80000000/serial@11300"
 
-- 
cgit v1.1


From eab1007334b93a6209f1ec33615e26ef5311ede7 Mon Sep 17 00:00:00 2001
From: "Steven A. Falco" <sfalco@harris.com>
Date: Wed, 6 Aug 2008 15:42:52 -0400
Subject: ppc4xx: Sequoia has two UARTs in "4-pin" mode. Configure the GPIOs as
 per schematic.

The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.

Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/sequoia.h | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index f4eefae..730037e 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -422,12 +422,12 @@
 /* GPIO Core 1 */									\
 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0	EBC_DATA(2)	*/	\
 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1	EBC_DATA(3)	*/	\
-{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N	UART1_DSR_CTS_N	UART2_SOUT*/ \
-{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
-{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0)	UART3_SIN*/ \
-{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N	EBC_DATA(1)	UART3_SOUT*/ \
-{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N	UART1_SOUT	*/	\
-{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N	UART1_SIN	*/	\
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_8PIN_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_CTS_N	EBC_DATA(0)	UART3_SIN*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N	EBC_DATA(1)	UART3_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_8PIN_DTR_N UART1_SOUT	*/	\
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_8PIN_RI_N UART1_SIN	*/	\
 {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0)			*/	\
 {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1)			*/	\
 {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2)			*/	\
-- 
cgit v1.1


From 3b8d17f0f082073346c0df017c9dfd6acdb40d6d Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Fri, 8 Aug 2008 16:41:56 +0200
Subject: TQM8xxL: fix support for second flash bank

When switching the TQM8xxL modules to use the CFI flash driver,
support for the second flash bank was broken because the CFI driver
did not support dynamically sized banks. This gets fixed now.

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/configs/TQM823L.h | 2 +-
 include/configs/TQM850L.h | 2 +-
 include/configs/TQM855L.h | 2 +-
 include/configs/TQM860L.h | 2 +-
 include/configs/TQM862L.h | 2 +-
 5 files changed, 5 insertions(+), 5 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
index 100be7c..3871722 100644
--- a/include/configs/TQM823L.h
+++ b/include/configs/TQM823L.h
@@ -196,7 +196,7 @@
 /* use CFI flash driver */
 #define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
 #define CFG_FLASH_EMPTY_INFO
 #define CFG_FLASH_USE_BUFFER_WRITE	1
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h
index 3097bc3..17afa89 100644
--- a/include/configs/TQM850L.h
+++ b/include/configs/TQM850L.h
@@ -183,7 +183,7 @@
 /* use CFI flash driver */
 #define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
 #define CFG_FLASH_EMPTY_INFO
 #define CFG_FLASH_USE_BUFFER_WRITE	1
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h
index 8ca8906..73d6583 100644
--- a/include/configs/TQM855L.h
+++ b/include/configs/TQM855L.h
@@ -187,7 +187,7 @@
 /* use CFI flash driver */
 #define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
 #define CFG_FLASH_EMPTY_INFO
 #define CFG_FLASH_USE_BUFFER_WRITE	1
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h
index f66aace..576e3e2 100644
--- a/include/configs/TQM860L.h
+++ b/include/configs/TQM860L.h
@@ -190,7 +190,7 @@
 /* use CFI flash driver */
 #define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
 #define CFG_FLASH_EMPTY_INFO
 #define CFG_FLASH_USE_BUFFER_WRITE	1
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
index 7813a20..6d2f91b 100644
--- a/include/configs/TQM862L.h
+++ b/include/configs/TQM862L.h
@@ -190,7 +190,7 @@
 /* use CFI flash driver */
 #define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
 #define CFG_FLASH_EMPTY_INFO
 #define CFG_FLASH_USE_BUFFER_WRITE	1
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
-- 
cgit v1.1


From 21f971ec265f6042ec21636d55d06a6bc0751077 Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Mon, 7 Jul 2008 01:22:29 +0200
Subject: TQM823L: re-enable logo support; update LCD_INFO text

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/configs/TQM823L.h | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
index 3871722..d5a3c54 100644
--- a/include/configs/TQM823L.h
+++ b/include/configs/TQM823L.h
@@ -37,6 +37,8 @@
 #define CONFIG_TQM823L		1	/* ...on a TQM8xxL module	*/
 
 #ifdef	CONFIG_LCD			/* with LCD controller ?	*/
+#define CONFIG_LCD_LOGO		1	/* print our logo on the LCD	*/
+#define CONFIG_LCD_INFO		1	/* ... and some board info	*/
 #define	CONFIG_SPLASH_SCREEN		/* ... with splashscreen support*/
 #endif
 
-- 
cgit v1.1


From ba9324451b662dd393afa53e5cc36fc5d3d10966 Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Date: Fri, 8 Aug 2008 16:30:23 +0900
Subject: sh: Update sh7763rdp config

Add sh_eth support to sh7763rdp.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
---
 include/configs/sh7763rdp.h | 9 +++++++++
 1 file changed, 9 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/sh7763rdp.h b/include/configs/sh7763rdp.h
index 7713eaa..5a65663 100644
--- a/include/configs/sh7763rdp.h
+++ b/include/configs/sh7763rdp.h
@@ -38,7 +38,11 @@
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_FLASH
 #define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
 #define CONFIG_CMD_ENV
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_JFFS2
 
 #define CONFIG_BOOTDELAY        -1
 #define CONFIG_BOOTARGS         "console=ttySC2,115200 root=1f01"
@@ -113,4 +117,9 @@
 #define TMU_CLK_DIVIDER		(4)	/* 4 (default), 16, 64, 256 or 1024 */
 #define CFG_HZ				(CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)
 
+/* Ether */
+#define CONFIG_SH_ETHER 1
+#define CONFIG_SH_ETHER_USE_PORT (1)
+#define CONFIG_SH_ETHER_PHY_ADDR (0x01)
+
 #endif /* __SH7763RDP_H */
-- 
cgit v1.1


From 29f8f58ff40c67f7f2e11afd1715173094e52ac2 Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Sat, 9 Aug 2008 23:17:32 +0200
Subject: TQM8xx{L,M}: try to normalize config files for TQM8xx? based board

- enable CFI driver where this was forgotten
- enable mtdparts support
- adjust default environment
etc.

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/configs/FPS850L.h  | 41 ++++++++++++++++++----
 include/configs/FPS860L.h  | 87 +++++++++++++++++++++++++++++++++++++++-------
 include/configs/NSCU.h     | 40 ++++++++++++++-------
 include/configs/TQM823L.h  | 27 ++++++++++++--
 include/configs/TQM823M.h  | 28 +++++++++++++--
 include/configs/TQM850L.h  | 27 ++++++++++++--
 include/configs/TQM850M.h  | 28 +++++++++++++--
 include/configs/TQM855L.h  | 28 +++++++++++++--
 include/configs/TQM855M.h  | 28 +++++++++++++--
 include/configs/TQM860L.h  | 24 +++++++++++--
 include/configs/TQM860M.h  | 26 +++++++++++---
 include/configs/TQM862L.h  | 28 +++++++++++++--
 include/configs/TQM862M.h  | 26 +++++++++++++-
 include/configs/TQM866M.h  | 29 +++++++++++++---
 include/configs/virtlab2.h | 40 +++++++++++++++------
 15 files changed, 440 insertions(+), 67 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/FPS850L.h b/include/configs/FPS850L.h
index e4b68ab..66db296 100644
--- a/include/configs/FPS850L.h
+++ b/include/configs/FPS850L.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -65,10 +65,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/fps850L/uImage\0"				\
+	"hostname=FPS850L\0"						\
+	"bootfile=FPS850L/uImage\0"					\
 	"fdt_addr=40040000\0"						\
 	"kernel_addr=40060000\0"					\
 	"ramdisk_addr=40200000\0"					\
+	"u-boot=FPS850L/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -106,10 +113,14 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -180,11 +191,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
@@ -194,6 +209,20 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
+/*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/FPS860L.h b/include/configs/FPS860L.h
index ed612c3..84607cc 100644
--- a/include/configs/FPS860L.h
+++ b/include/configs/FPS860L.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -65,10 +65,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/fps850L/uImage\0"				\
+	"hostname=FPS860L\0"						\
+	"bootfile=FPS860L/uImage\0"					\
 	"fdt_addr=40040000\0"						\
 	"kernel_addr=40060000\0"					\
 	"ramdisk_addr=40200000\0"					\
+	"u-boot=FPS860L/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -106,10 +113,14 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -180,11 +191,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	67	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
@@ -194,6 +209,20 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
+/*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
@@ -306,9 +335,11 @@
 #define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
 #define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
 
-/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1	*/
-#define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV2 | OR_BI | \
-				 OR_SCY_5_CLK | OR_EHTR)
+/*
+ * FLASH timing:
+ */
+#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
+				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -337,12 +368,42 @@
 
 /*
  * Memory Periodic Timer Prescaler
+ *
+ * The Divider for PTA (refresh timer) configuration is based on an
+ * example SDRAM configuration (64 MBit, one bank). The adjustment to
+ * the number of chip selects (NCS) and the actually needed refresh
+ * rate is done by setting MPTPR.
+ *
+ * PTA is calculated from
+ *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
+ *
+ *	gclk	  CPU clock (not bus clock!)
+ *	Trefresh  Refresh cycle * 4 (four word bursts used)
+ *
+ * 4096  Rows from SDRAM example configuration
+ * 1000  factor s -> ms
+ *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
+ *    4  Number of refresh cycles per period
+ *   64  Refresh cycle in ms per number of rows
+ * --------------------------------------------
+ * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
+ *
+ * 50 MHz => 50.000.000 / Divider =  98
+ * 66 Mhz => 66.000.000 / Divider = 129
+ * 80 Mhz => 80.000.000 / Divider = 156
  */
 
-/* periodic timer for refresh */
-#define CFG_MAMR_PTA	97		/* start with divider for 100 MHz	*/
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
+/*
+ * For 16 MBit, refresh rates could be 31.3 us
+ * (= 64 ms / 2K = 125 / quad bursts).
+ * For a simpler initialization, 15.6 us is used instead.
+ *
+ * #define CFG_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
+ * #define CFG_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
+ */
 #define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
 #define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
 
@@ -372,4 +433,6 @@
 #define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
+#define CONFIG_SCC1_ENET
+
 #endif	/* __CONFIG_H */
diff --git a/include/configs/NSCU.h b/include/configs/NSCU.h
index 11e5c63..21d90c3 100644
--- a/include/configs/NSCU.h
+++ b/include/configs/NSCU.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -67,9 +67,16 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/NSCU/uImage\0"				\
+	"hostname=NSCU\0"						\
+	"bootfile=${hostname}/uImage\0"					\
 	"kernel_addr=40080000\0"					\
 	"ramdisk_addr=40180000\0"					\
+	"u-boot=${hostname}/u-image.bin\0"				\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -110,20 +117,24 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
 #define	CFG_LONGHELP			/* undef to save memory		*/
 #define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
 
-#if 0
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history
+*/
 #define	CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
-#endif
 #ifdef	CFG_HUSH_PARSER
 #define	CFG_PROMPT_HUSH_PS2	"> "
 #endif
@@ -186,21 +197,26 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
-#define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
-#define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
+#define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
-#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
index d5a3c54..f807271 100644
--- a/include/configs/TQM823L.h
+++ b/include/configs/TQM823L.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -71,10 +71,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM823L/uImage\0"				\
+	"hostname=TQM823L\0"						\
+	"bootfile=TQM823L/uImage\0"					\
 	"fdt_addr=40040000\0"						\
 	"kernel_addr=40060000\0"					\
 	"ramdisk_addr=40200000\0"					\
+	"u-boot=TQM823L/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -115,7 +122,9 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
@@ -124,6 +133,8 @@
 #endif
 
 
+#define CONFIG_NETCONSOLE
+
 /*
  * Miscellaneous configurable options
  */
@@ -215,6 +226,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h
index 40dc26b..431ae8c 100644
--- a/include/configs/TQM823M.h
+++ b/include/configs/TQM823M.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -69,10 +69,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM823M/uImage\0"				\
+	"hostname=TQM823M\0"						\
+	"bootfile=TQM823M/uImage\0"					\
 	"fdt_addr=40080000\0"						\
 	"kernel_addr=400A0000\0"					\
 	"ramdisk_addr=40280000\0"					\
+	"u-boot=TQM823M/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -113,11 +120,16 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -210,6 +222,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
+						"128k(dtb),"		\
+						"1920k(kernel),"	\
+						"5632(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h
index 17afa89..7946c13 100644
--- a/include/configs/TQM850L.h
+++ b/include/configs/TQM850L.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -65,10 +65,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM850L/uImage\0"				\
+	"hostname=TQM850L\0"						\
+	"bootfile=TQM850L/uImage\0"					\
 	"fdt_addr=40040000\0"						\
 	"kernel_addr=40060000\0"					\
 	"ramdisk_addr=40200000\0"					\
+	"u-boot=TQM850L/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -104,11 +111,15 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
 /*
  * Miscellaneous configurable options
  */
@@ -200,6 +211,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h
index becf82c..777776d 100644
--- a/include/configs/TQM850M.h
+++ b/include/configs/TQM850M.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -63,10 +63,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM850M/uImage\0"				\
+	"hostname=TQM850M\0"						\
+	"bootfile=TQM850M/uImage\0"					\
 	"fdt_addr=40080000\0"						\
 	"kernel_addr=400A0000\0"					\
 	"ramdisk_addr=40280000\0"					\
+	"u-boot=TQM850M/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -102,11 +109,16 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -199,6 +211,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
+						"128k(dtb),"		\
+						"1920k(kernel),"	\
+						"5632(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h
index 73d6583..0549cbd 100644
--- a/include/configs/TQM855L.h
+++ b/include/configs/TQM855L.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -68,10 +68,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM855L/uImage\0"				\
+	"hostname=TQM855L\0"						\
+	"bootfile=TQM855L/uImage\0"					\
 	"fdt_addr=40040000\0"						\
 	"kernel_addr=40060000\0"					\
 	"ramdisk_addr=40200000\0"					\
+	"u-boot=TQM855L/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -108,11 +115,16 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -204,6 +216,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index 2696ea5..bc092b7 100644
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -68,10 +68,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM855M/uImage\0"				\
+	"hostname=TQM855M\0"						\
+	"bootfile=TQM855M/uImage\0"					\
 	"fdt_addr=40080000\0"						\
 	"kernel_addr=400A0000\0"					\
 	"ramdisk_addr=40280000\0"					\
+	"u-boot=TQM855M/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -141,12 +148,17 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -239,6 +251,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
+						"128k(dtb),"		\
+						"1920k(kernel),"	\
+						"5632(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h
index 576e3e2..065156f 100644
--- a/include/configs/TQM860L.h
+++ b/include/configs/TQM860L.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -68,10 +68,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM860L/uImage\0"				\
+	"hostname=TQM860L\0"						\
+	"bootfile=TQM860L/uImage\0"					\
 	"fdt_addr=40040000\0"						\
 	"kernel_addr=40060000\0"					\
 	"ramdisk_addr=40200000\0"					\
+	"u-boot=TQM860L/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -110,6 +117,7 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
@@ -207,6 +215,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
index 00b7853..ff610bf 100644
--- a/include/configs/TQM860M.h
+++ b/include/configs/TQM860M.h
@@ -68,15 +68,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM860M/uImage\0"				\
+	"hostname=TQM860M\0"						\
+	"bootfile=TQM860M/uImage\0"					\
 	"fdt_addr=400C0000\0"						\
 	"kernel_addr=40100000\0"					\
 	"ramdisk_addr=40280000\0"					\
+	"u-boot=TQM860M/u-image.bin\0"					\
 	"load=tftp 200000 ${u-boot}\0"					\
-	"update=protect off 40000000 +${filesize};"			\
-		"erase 40000000 +${filesize};"				\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
 		"cp.b 200000 40000000 ${filesize};"			\
-		"protect on 40000000 +${filesize}\0"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -115,10 +117,14 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -210,6 +216,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
+						"128k(dtb),"		\
+						"1920k(kernel),"	\
+						"5632(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
index 6d2f91b..33ff8a9 100644
--- a/include/configs/TQM862L.h
+++ b/include/configs/TQM862L.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -71,10 +71,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM862L/uImage\0"				\
+	"hostname=TQM862L\0"						\
+	"bootfile=TQM862L/uImage\0"					\
 	"fdt_addr=40040000\0"						\
 	"kernel_addr=40060000\0"					\
 	"ramdisk_addr=40200000\0"					\
+	"u-boot=TQM862L/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -111,11 +118,16 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -207,6 +219,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h
index 05395e0..1ec4431 100644
--- a/include/configs/TQM862M.h
+++ b/include/configs/TQM862M.h
@@ -71,10 +71,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM862M/uImage\0"				\
+	"hostname=TQM862M\0"						\
+	"bootfile=TQM862M/uImage\0"					\
 	"fdt_addr=40080000\0"						\
 	"kernel_addr=400A0000\0"					\
 	"ramdisk_addr=40280000\0"					\
+	"u-boot=TQM862M/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -111,11 +118,16 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 
+#define CONFIG_NETCONSOLE
+
+
 /*
  * Miscellaneous configurable options
  */
@@ -208,6 +220,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
+						"128k(dtb),"		\
+						"1920k(kernel),"	\
+						"5632(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index d033875..0cee9f4 100644
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -80,15 +80,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM866M/uImage\0"				\
+	"hostname=TQM866M\0"						\
+	"bootfile=TQM866M/uImage\0"					\
 	"fdt_addr=400C0000\0"						\
 	"kernel_addr=40100000\0"					\
 	"ramdisk_addr=40280000\0"					\
+	"u-boot=TQM866M/u-image.bin\0"					\
 	"load=tftp 200000 ${u-boot}\0"					\
-	"update=protect off 40000000 +${filesize};"			\
-		"erase 40000000 +${filesize};"				\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
 		"cp.b 200000 40000000 ${filesize};"			\
-		"protect on 40000000 +${filesize}\0"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -157,9 +159,14 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+
+
+#define CONFIG_NETCONSOLE
 
 
 /*
@@ -253,6 +260,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
+						"128k(dtb),"		\
+						"1920k(kernel),"	\
+						"5632(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
diff --git a/include/configs/virtlab2.h b/include/configs/virtlab2.h
index 6bb075d..54d9421 100644
--- a/include/configs/virtlab2.h
+++ b/include/configs/virtlab2.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2006
+ * (C) Copyright 2006-2008
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -37,10 +37,6 @@
 #define CONFIG_VIRTLAB2		1	/* ...on a virtlab2 module	*/
 #define	CONFIG_TQM8xxL		1
 
-#ifdef	CONFIG_LCD			/* with LCD controller ?	*/
-#define	CONFIG_SPLASH_SCREEN		/* ... with splashscreen support*/
-#endif
-
 #define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 #undef	CONFIG_8xx_CONS_SMC2
 #undef	CONFIG_8xx_CONS_NONE
@@ -70,9 +66,17 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM823L/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
+	"hostname=virtlab2\0"						\
+	"bootfile=virtlab2/uImage\0"					\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
+	"u-boot=virtlab2/u-image.bin\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=prot off 40000000 +${filesize};"			\
+		"era 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -114,6 +118,7 @@
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
@@ -122,15 +127,16 @@
 #endif
 
 
+#define CONFIG_NETCONSOLE
+
 /*
  * Miscellaneous configurable options
  */
 #define	CFG_LONGHELP			/* undef to save memory		*/
 #define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
 
-#if 0
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define	CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
-#endif
 #ifdef	CFG_HUSH_PARSER
 #define	CFG_PROMPT_HUSH_PS2	"> "
 #endif
@@ -197,7 +203,7 @@
 /* use CFI flash driver */
 #define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
 #define CFG_FLASH_EMPTY_INFO
 #define CFG_FLASH_USE_BUFFER_WRITE	1
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
@@ -214,6 +220,18 @@
 #define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT	"mtdparts=TQM8xxL-0:256k(u-boot),"	\
+						"128k(dtb),"		\
+						"1664k(kernel),"	\
+						"2m(rootfs),"		\
+						"4m(data)"	
+
+/*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-- 
cgit v1.1


From 23f935c073e7578c6066804fd2f9ee116cae6ffe Mon Sep 17 00:00:00 2001
From: Becky Bruce <becky.bruce@freescale.com>
Date: Mon, 4 Aug 2008 14:01:16 -0500
Subject: POWERPC: 86xx - add missing CONFIG_HIGH_BATS to sbc8641d config

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/sbc8641d.h | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index 3cd9ff8..ebfcb46 100644
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -58,6 +58,8 @@
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
+#define CONFIG_HIGH_BATS	1	/* High BATs supported and enabled */
+
 #undef CONFIG_SPD_EEPROM		/* Do not use SPD EEPROM for DDR setup*/
 #undef CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-- 
cgit v1.1


From 17e900b8c0f38d922da47073246219dce2a847f2 Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Tue, 12 Aug 2008 14:54:04 +0200
Subject: MVBC_P: fix compile problem

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/configs/MVBC_P.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MVBC_P.h b/include/configs/MVBC_P.h
index 8c8a445..2c27b97 100644
--- a/include/configs/MVBC_P.h
+++ b/include/configs/MVBC_P.h
@@ -40,7 +40,7 @@
 #define CONFIG_MISC_INIT_R	1
 
 #define CFG_CACHELINE_SIZE	32
-#ifdef (CONFIG_CMD_KGDB)
+#ifdef CONFIG_CMD_KGDB
 #define CFG_CACHELINE_SHIFT	5
 #endif
 
@@ -268,7 +268,7 @@
 #define CFG_PROMPT_HUSH_PS2 	"> "
 #undef 	CFG_LONGHELP
 #define CFG_PROMPT		"=> "
-#ifdef (CONFIG_CMD_KGDB)
+#ifdef CONFIG_CMD_KGDB
 #define CFG_CBSIZE		1024
 #else
 #define CFG_CBSIZE		256
-- 
cgit v1.1


From cd82919e6c8a73b363a26f34b734923844e52d1c Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Tue, 12 Aug 2008 16:08:38 +0200
Subject: Coding style cleanup, update CHANGELOG, prepare release

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/configs/FPS850L.h  | 2 +-
 include/configs/FPS860L.h  | 2 +-
 include/configs/TQM823L.h  | 2 +-
 include/configs/TQM823M.h  | 2 +-
 include/configs/TQM850L.h  | 2 +-
 include/configs/TQM850M.h  | 2 +-
 include/configs/TQM855L.h  | 2 +-
 include/configs/TQM855M.h  | 2 +-
 include/configs/TQM860L.h  | 2 +-
 include/configs/TQM860M.h  | 2 +-
 include/configs/TQM862L.h  | 2 +-
 include/configs/TQM862M.h  | 2 +-
 include/configs/TQM866M.h  | 2 +-
 include/configs/virtlab2.h | 2 +-
 14 files changed, 14 insertions(+), 14 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/FPS850L.h b/include/configs/FPS850L.h
index 66db296..79b71db 100644
--- a/include/configs/FPS850L.h
+++ b/include/configs/FPS850L.h
@@ -221,7 +221,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/FPS860L.h b/include/configs/FPS860L.h
index 84607cc..ec757e2 100644
--- a/include/configs/FPS860L.h
+++ b/include/configs/FPS860L.h
@@ -221,7 +221,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
index f807271..9cc1964 100644
--- a/include/configs/TQM823L.h
+++ b/include/configs/TQM823L.h
@@ -235,7 +235,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h
index 431ae8c..5edd379 100644
--- a/include/configs/TQM823M.h
+++ b/include/configs/TQM823M.h
@@ -231,7 +231,7 @@
 						"128k(dtb),"		\
 						"1920k(kernel),"	\
 						"5632(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h
index 7946c13..9edf0d8 100644
--- a/include/configs/TQM850L.h
+++ b/include/configs/TQM850L.h
@@ -220,7 +220,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h
index 777776d..e2c1ce8 100644
--- a/include/configs/TQM850M.h
+++ b/include/configs/TQM850M.h
@@ -220,7 +220,7 @@
 						"128k(dtb),"		\
 						"1920k(kernel),"	\
 						"5632(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h
index 0549cbd..dd19d4e 100644
--- a/include/configs/TQM855L.h
+++ b/include/configs/TQM855L.h
@@ -225,7 +225,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index bc092b7..8a1c350 100644
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -260,7 +260,7 @@
 						"128k(dtb),"		\
 						"1920k(kernel),"	\
 						"5632(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h
index 065156f..803cdb8 100644
--- a/include/configs/TQM860L.h
+++ b/include/configs/TQM860L.h
@@ -224,7 +224,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
index ff610bf..071da1e 100644
--- a/include/configs/TQM860M.h
+++ b/include/configs/TQM860M.h
@@ -225,7 +225,7 @@
 						"128k(dtb),"		\
 						"1920k(kernel),"	\
 						"5632(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
index 33ff8a9..d34f6be 100644
--- a/include/configs/TQM862L.h
+++ b/include/configs/TQM862L.h
@@ -228,7 +228,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h
index 1ec4431..9270e44 100644
--- a/include/configs/TQM862M.h
+++ b/include/configs/TQM862M.h
@@ -229,7 +229,7 @@
 						"128k(dtb),"		\
 						"1920k(kernel),"	\
 						"5632(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index 0cee9f4..d916d53 100644
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -269,7 +269,7 @@
 						"128k(dtb),"		\
 						"1920k(kernel),"	\
 						"5632(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
diff --git a/include/configs/virtlab2.h b/include/configs/virtlab2.h
index 54d9421..f104886 100644
--- a/include/configs/virtlab2.h
+++ b/include/configs/virtlab2.h
@@ -229,7 +229,7 @@
 						"128k(dtb),"		\
 						"1664k(kernel),"	\
 						"2m(rootfs),"		\
-						"4m(data)"	
+						"4m(data)"
 
 /*-----------------------------------------------------------------------
  * Hardware Information Block
-- 
cgit v1.1