From 5bcd64cf5c5510365a14d11043033eb7b6144ead Mon Sep 17 00:00:00 2001 From: Karlheinz Jerg Date: Mon, 21 Jan 2013 03:55:18 +0000 Subject: powerpc/83xx/km: add MV88E6122 switch support for kmvect1 kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection to the switch MV88E6122. This switch has a connection to a frontport ethernet interface. The ethernet port used for network booting is automatically selected by u-boot. If a Piggy is plugged, the Piggy port is selected (UEC2, eth1). If the Piggy isn't present, the Frontport is selected (UEC0, eth0). The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28) and released at startup. Signed-off-by: Karlheinz Jerg Signed-off-by: Holger Brunck --- include/configs/km/km83xx-common.h | 8 ++------ include/configs/suvd3.h | 37 +++++++++++++++++++++++++++++++++++++ 2 files changed, 39 insertions(+), 6 deletions(-) (limited to 'include/configs') diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h index a9823d6..1e596c8 100644 --- a/include/configs/km/km83xx-common.h +++ b/include/configs/km/km83xx-common.h @@ -165,19 +165,15 @@ #define CONFIG_UEC_ETH #define CONFIG_ETHPRIME "UEC0" +#if !defined(CONFIG_MPC8309) #define CONFIG_UEC_ETH1 /* GETH1 */ #define UEC_VERBOSE_DEBUG 1 +#endif #ifdef CONFIG_UEC_ETH1 -#if defined(CONFIG_MPC8309) -#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 -#else #define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ #define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#endif #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH #define CONFIG_SYS_UEC1_PHY_ADDR 0 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h index c50832c..bbf9da5 100644 --- a/include/configs/suvd3.h +++ b/include/configs/suvd3.h @@ -110,4 +110,41 @@ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +/* + * QE UEC ethernet configuration + */ +#if defined(CONFIG_KMVECT1) +#define CONFIG_MV88E6352_SWITCH +#define CONFIG_KM_MVEXTSW_ADDR 0x10 + +/* ethernet port connected to simple switch 88e6122 (UEC0) */ +#define CONFIG_UEC_ETH1 +#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 + +#define CONFIG_FIXED_PHY 0xFFFFFFFF +#define CONFIG_SYS_FIXED_PHY_ADDR 0x1E /* unused address */ +#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \ + {devnum, speed, duplex} +#define CONFIG_SYS_FIXED_PHY_PORTS \ + CONFIG_SYS_FIXED_PHY_PORT("UEC0", SPEED_100, DUPLEX_FULL) + +#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR CONFIG_SYS_FIXED_PHY_ADDR +#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII +#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 + +/* ethernet port connected to piggy (UEC2) */ +#define CONFIG_HAS_ETH1 +#define CONFIG_UEC_ETH2 +#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */ +#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ +#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12 +#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC2_PHY_ADDR 0 +#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII +#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 +#endif /* CONFIG_KMVECT1 */ + #endif /* __CONFIG_H */ -- cgit v1.1