From 69df3c4da0c93017cceb25a366e794570bd0ed98 Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <iwamatsu@rahute.(none)>
Date: Sun, 13 May 2007 21:01:03 +0900
Subject: sh: MS7750SE support.

This adds support for the Hitachi MS7750SE.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
 include/configs/ms7750se.h | 75 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 75 insertions(+)
 create mode 100644 include/configs/ms7750se.h

(limited to 'include/configs')

diff --git a/include/configs/ms7750se.h b/include/configs/ms7750se.h
new file mode 100644
index 0000000..0467a5e
--- /dev/null
+++ b/include/configs/ms7750se.h
@@ -0,0 +1,75 @@
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+#define CONFIG_SH		1
+#define CONFIG_SH4		1
+#define CONFIG_CPU_SH7750	1
+#define CONFIG_MS7750SE		1
+#define __LITTLE_ENDIAN__	1
+
+//#define CONFIG_COMMANDS         (CONFIG_CMD_DFL | CFG_CMD_NET |CFG_CMD_PING)
+#define CONFIG_COMMANDS        	CONFIG_CMD_DFL & ~CFG_CMD_NET 
+
+#define CFG_SCIF_CONSOLE	1
+#define CONFIG_BAUDRATE		38400
+#define CONFIG_CONS_SCIF1	1
+#define BOARD_LATE_INIT		1
+
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY	-1
+#define CONFIG_BOOTARGS    	"console=ttySC0,115200"
+#define CONFIG_ENV_OVERWRITE	1
+
+#define CFG_SDRAM_BASE		(0x8C000000)
+#define CFG_SDRAM_SIZE		(64 * 1024 * 1024)
+
+#define CFG_LONGHELP		
+#define CFG_PROMPT		"=> "		
+#define CFG_CBSIZE		256	
+#define CFG_PBSIZE		256	
+#define CFG_MAXARGS		16
+#define CFG_BARGSIZE		512	
+#define CFG_BAUDRATE_TABLE	{ 115200, 57600, 38400, 19200, 9600 }		/* List of legal baudrate settings for this board */
+
+#define CFG_MEMTEST_START	(CFG_SDRAM_BASE)
+#define CFG_MEMTEST_END		(TEXT_BASE - 0x100000)
+
+
+#define CFG_LOAD_ADDR		(CFG_SDRAM_BASE + 4 * 1024 * 1024)
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE)	/* Address of u-boot image in Flash */
+#define CFG_MONITOR_LEN		(128 * 1024)	
+#define CFG_MALLOC_LEN		(256 * 1024)		/* Size of DRAM reserved for malloc() use */
+
+#define CFG_GBL_DATA_SIZE	(256)			/* size in bytes reserved for initial data */
+#define CFG_BOOTMAPSZ		(8 * 1024 * 1024)	
+#define CFG_RX_ETH_BUFFER	(8)
+
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER
+#undef CFG_FLASH_CFI_BROKEN_TABLE
+#undef  CFG_FLASH_QUIET_TEST
+#define CFG_FLASH_EMPTY_INFO				/* print 'E' for empty sector on flinfo */
+
+#define CFG_FLASH_BASE		(0xA1000000)
+#define CFG_MAX_FLASH_BANKS	(1)			/* Max number of 
+						 	 * Flash memory banks
+						 	 */
+#define CFG_MAX_FLASH_SECT	142
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+
+#define CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x20000
+#define CFG_ENV_SIZE		(CFG_ENV_SECT_SIZE)
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CFG_FLASH_ERASE_TOUT  	120000
+#define CFG_FLASH_WRITE_TOUT	500
+
+#define CONFIG_SYS_CLK_FREQ	33333333
+#define TMU_CLK_DIVIDER		4
+#define CFG_HZ			(CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)
+#define	CFG_PLL_SETTLING_TIME	100		/* in us */
+
+#endif /* __CONFIG_H */
-- 
cgit v1.1


From 047375bfa4c3052fa50a748da7ff89e9dad3b364 Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Date: Sun, 23 Sep 2007 02:19:24 +0900
Subject: sh: Update MS7750SE01 platform

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
 include/configs/ms7750se.h | 79 ++++++++++++++++++++++++++++++++--------------
 1 file changed, 56 insertions(+), 23 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/ms7750se.h b/include/configs/ms7750se.h
index 0467a5e..7925f20 100644
--- a/include/configs/ms7750se.h
+++ b/include/configs/ms7750se.h
@@ -1,50 +1,89 @@
-#ifndef __CONFIG_H
-#define __CONFIG_H
+/*
+ * Configuation settings for the Hitachi Solution Engine 7750
+ *
+ * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __MS7750SE_H
+#define __MS7750SE_H
 
 #undef DEBUG
-
 #define CONFIG_SH		1
 #define CONFIG_SH4		1
 #define CONFIG_CPU_SH7750	1
+/* #define CONFIG_CPU_SH7751	1 */
+/* #define CONFIG_CPU_TYPE_R	1 */
 #define CONFIG_MS7750SE		1
 #define __LITTLE_ENDIAN__	1
 
-//#define CONFIG_COMMANDS         (CONFIG_CMD_DFL | CFG_CMD_NET |CFG_CMD_PING)
-#define CONFIG_COMMANDS        	CONFIG_CMD_DFL & ~CFG_CMD_NET 
+/*
+ * Command line configuration.
+ */
+//#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DFL
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_ENV
 
 #define CFG_SCIF_CONSOLE	1
 #define CONFIG_BAUDRATE		38400
 #define CONFIG_CONS_SCIF1	1
 #define BOARD_LATE_INIT		1
 
-#include <cmd_confdefs.h>
-
 #define CONFIG_BOOTDELAY	-1
-#define CONFIG_BOOTARGS    	"console=ttySC0,115200"
+#define CONFIG_BOOTARGS    	"console=ttySC0,38400"
 #define CONFIG_ENV_OVERWRITE	1
 
+/* SDRAM */
 #define CFG_SDRAM_BASE		(0x8C000000)
 #define CFG_SDRAM_SIZE		(64 * 1024 * 1024)
 
 #define CFG_LONGHELP		
-#define CFG_PROMPT		"=> "		
-#define CFG_CBSIZE		256	
-#define CFG_PBSIZE		256	
+#define CFG_PROMPT		"=> "
+#define CFG_CBSIZE		256
+#define CFG_PBSIZE		256
 #define CFG_MAXARGS		16
-#define CFG_BARGSIZE		512	
-#define CFG_BAUDRATE_TABLE	{ 115200, 57600, 38400, 19200, 9600 }		/* List of legal baudrate settings for this board */
+#define CFG_BARGSIZE		512
+/* List of legal baudrate settings for this board */
+#define CFG_BAUDRATE_TABLE	{ 115200, 57600, 38400, 19200, 9600 }
 
 #define CFG_MEMTEST_START	(CFG_SDRAM_BASE)
 #define CFG_MEMTEST_END		(TEXT_BASE - 0x100000)
 
+/* NOR Flash */
+/* #define CFG_FLASH_BASE		(0xA1000000)*/
+#define CFG_FLASH_BASE		(0xA0000000)
+#define CFG_MAX_FLASH_BANKS	(1)	/* Max number of 
+				 	 * Flash memory banks
+				 	 */
+#define CFG_MAX_FLASH_SECT	142
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
 
 #define CFG_LOAD_ADDR		(CFG_SDRAM_BASE + 4 * 1024 * 1024)
 #define CFG_MONITOR_BASE	(CFG_FLASH_BASE)	/* Address of u-boot image in Flash */
-#define CFG_MONITOR_LEN		(128 * 1024)	
+#define CFG_MONITOR_LEN		(128 * 1024)
 #define CFG_MALLOC_LEN		(256 * 1024)		/* Size of DRAM reserved for malloc() use */
 
 #define CFG_GBL_DATA_SIZE	(256)			/* size in bytes reserved for initial data */
-#define CFG_BOOTMAPSZ		(8 * 1024 * 1024)	
+#define CFG_BOOTMAPSZ		(8 * 1024 * 1024)
 #define CFG_RX_ETH_BUFFER	(8)
 
 #define CFG_FLASH_CFI
@@ -53,12 +92,6 @@
 #undef  CFG_FLASH_QUIET_TEST
 #define CFG_FLASH_EMPTY_INFO				/* print 'E' for empty sector on flinfo */
 
-#define CFG_FLASH_BASE		(0xA1000000)
-#define CFG_MAX_FLASH_BANKS	(1)			/* Max number of 
-						 	 * Flash memory banks
-						 	 */
-#define CFG_MAX_FLASH_SECT	142
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
 
 #define CFG_ENV_IS_IN_FLASH
 #define CFG_ENV_SECT_SIZE	0x20000
@@ -67,9 +100,9 @@
 #define CFG_FLASH_ERASE_TOUT  	120000
 #define CFG_FLASH_WRITE_TOUT	500
 
+/* Board Clock */
 #define CONFIG_SYS_CLK_FREQ	33333333
 #define TMU_CLK_DIVIDER		4
 #define CFG_HZ			(CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)
-#define	CFG_PLL_SETTLING_TIME	100		/* in us */
 
-#endif /* __CONFIG_H */
+#endif /* __MS7750SE_H */
-- 
cgit v1.1


From 6c0bbdccd379f5c8702af9e0765294c2fb7472a6 Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Date: Sun, 23 Sep 2007 02:31:13 +0900
Subject: sh: Add support Renesas sh7722 processor and Hitachi MS7722SE01 board

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
 include/configs/ms7722se.h | 137 +++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 137 insertions(+)
 create mode 100644 include/configs/ms7722se.h

(limited to 'include/configs')

diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h
new file mode 100644
index 0000000..18e9851
--- /dev/null
+++ b/include/configs/ms7722se.h
@@ -0,0 +1,137 @@
+/*
+ * Configuation settings for the Hitachi Solution Engine 7722
+ *
+ * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __MS7722SE_H
+#define __MS7722SE_H
+
+#undef DEBUG 
+#define CONFIG_SH		1
+#define CONFIG_SH4		1
+#define CONFIG_CPU_SH7722	1
+#define CONFIG_MS7722SE		1
+
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DFL
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_ENV
+
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_BOOTARGS    	"console=ttySC0,115200 root=1f01"
+#define CONFIG_NETMASK          255.255.255.0
+#define CONFIG_IPADDR		192.168.0.22
+#define CONFIG_SERVERIP		192.168.0.1
+#define CONFIG_GATEWAYIP	192.168.0.1
+
+#define CONFIG_VERSION_VARIABLE
+#undef  CONFIG_SHOW_BOOT_PROGRESS
+
+/* SMC9111 */
+#define CONFIG_DRIVER_SMC91111
+#define CONFIG_SMC91111_BASE    (0xB8000000)
+
+/* MEMORY */
+#define MS7722SE_SDRAM_BASE	(0x8C000000)
+#define MS7722SE_FLASH_BASE_1	(0xA0000000)
+//#define MS7722SE_FLASH_BASE_1	(0xA1000000)
+#define MS7722SE_FLASH_BANK_SIZE	(8*1024 * 1024)
+
+#define CFG_LONGHELP				/* undef to save memory	*/
+#define CFG_PROMPT		"=> "		/* Monitor Command Prompt */
+#define CFG_CBSIZE		256		/* Buffer size for input from the Console */
+#define CFG_PBSIZE		256		/* Buffer size for Console output */
+#define CFG_MAXARGS		16		/* max args accepted for monitor commands */
+#define CFG_BARGSIZE		512		/* Buffer size for Boot Arguments passed to kernel */
+#define CFG_BAUDRATE_TABLE	{ 115200 }	/* List of legal baudrate settings for this board */
+
+/* SCIF */
+#define CFG_SCIF_CONSOLE	1
+#define CONFIG_CONS_SCIF0	1
+#undef  CFG_CONSOLE_INFO_QUIET			/* Suppress display of console information at boot */
+#undef  CFG_CONSOLE_OVERWRITE_ROUTINE
+#undef  CFG_CONSOLE_ENV_OVERWRITE
+
+#define CFG_MEMTEST_START	(MS7722SE_SDRAM_BASE)
+#define CFG_MEMTEST_END		(CFG_MEMTEST_START + (60 * 1024 * 1024))
+
+#undef  CFG_ALT_MEMTEST		/* Enable alternate, more extensive, memory test */
+#undef  CFG_MEMTEST_SCRATCH	/* Scratch address used by the alternate memory test */
+
+#undef  CFG_LOADS_BAUD_CHANGE	/* Enable temporary baudrate change while serial download */
+
+#define CFG_SDRAM_BASE	(MS7722SE_SDRAM_BASE)
+#define CFG_SDRAM_SIZE	(64 * 1024 * 1024)	/* maybe more, but if so u-boot doesn't know about it... */
+
+#define CFG_LOAD_ADDR	(CFG_SDRAM_BASE + 4 * 1024 * 1024)	/* default load address for scripts ?!? */
+
+#define CFG_MONITOR_BASE	(MS7722SE_FLASH_BASE_1)	/* Address of u-boot image 
+						   	in Flash (NOT run time address in SDRAM) ?!? */
+#define CFG_MONITOR_LEN	(128 * 1024)		/* */
+#define CFG_MALLOC_LEN	(256 * 1024)		/* Size of DRAM reserved for malloc() use */
+#define CFG_GBL_DATA_SIZE	(256)		/* size in bytes reserved for initial data */
+#define CFG_BOOTMAPSZ	(8 * 1024 * 1024)	
+
+/* FLASH */
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER
+#undef  CFG_FLASH_QUIET_TEST
+#define CFG_FLASH_EMPTY_INFO			/* print 'E' for empty sector on flinfo */
+
+#define CFG_FLASH_BASE		(MS7722SE_FLASH_BASE_1)	/* Physical start address of Flash memory */
+
+#define CFG_MAX_FLASH_SECT	150		/* Max number of sectors on each 
+				   			Flash chip */
+
+/* if you use all NOR Flash , you change dip-switch. Please see MS7722SE01 Manual. */
+#define CFG_MAX_FLASH_BANKS	2
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE + (0 * MS7722SE_FLASH_BANK_SIZE), \
+				  CFG_FLASH_BASE + (1 * MS7722SE_FLASH_BANK_SIZE), \
+				}
+
+#define CFG_FLASH_ERASE_TOUT	(3 * 1000)	/* Timeout for Flash erase operations (in ms) */
+#define CFG_FLASH_WRITE_TOUT	(3 * 1000)	/* Timeout for Flash write operations (in ms) */
+#define CFG_FLASH_LOCK_TOUT	(3 * 1000)	/* Timeout for Flash set sector lock bit operations (in ms) */
+#define CFG_FLASH_UNLOCK_TOUT	(3 * 1000)	/* Timeout for Flash clear lock bit operations (in ms) */
+
+#undef  CFG_FLASH_PROTECTION			/* Use hardware flash sectors protection instead of U-Boot software protection */
+
+#undef  CFG_DIRECT_FLASH_TFTP
+
+#define CFG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OVERWRITE	1
+#define CFG_ENV_SECT_SIZE	(8 * 1024)
+#define CFG_ENV_SIZE		(CFG_ENV_SECT_SIZE)
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + (1 * CFG_ENV_SECT_SIZE))
+#define CFG_ENV_OFFSET		(CFG_ENV_ADDR - CFG_FLASH_BASE) 	/* Offset of env Flash sector relative to CFG_FLASH_BASE */
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SECT_SIZE)
+#define CFG_ENV_ADDR_REDUND	(CFG_FLASH_BASE + (2 * CFG_ENV_SECT_SIZE))
+
+/* Board Clock */
+#define CONFIG_SYS_CLK_FREQ	33333333
+#define TMU_CLK_DIVIDER		(4)	/* 4 (default), 16, 64, 256 or 1024 */		
+#define CFG_HZ			(CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)
+
+#endif	/* __MS7722SE_H */
-- 
cgit v1.1


From 9553df86d3a319c3a1a7cde7e4edd6eeb5aa64c7 Mon Sep 17 00:00:00 2001
From: Jon Loeliger <jdl@freescale.com>
Date: Tue, 16 Oct 2007 15:26:51 -0500
Subject: Initial mpc8610hpcd cpu/, README and include/ files.

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8610HPCD.h | 660 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 660 insertions(+)
 create mode 100644 include/configs/MPC8610HPCD.h

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
new file mode 100644
index 0000000..be3434a
--- /dev/null
+++ b/include/configs/MPC8610HPCD.h
@@ -0,0 +1,660 @@
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+/*
+ * MPC8610HPCD board configuration file
+ *
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_MPC86xx		1	/* MPC86xx */
+#define CONFIG_MPC8610		1	/* MPC8610 specific */
+#define CONFIG_MPC8610HPCD	1	/* MPC8610HPCD board specific */
+#define CONFIG_NUM_CPUS		1	/* Number of CPUs in the system */
+#define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
+
+#ifdef RUN_DIAG
+#define CFG_DIAG_ADDR		0xff800000
+#endif
+
+#define CFG_RESET_ADDRESS	0xfff00100
+
+#define CONFIG_PCI		1	/* Enable PCI/PCIE*/
+#define CONFIG_PCI1		1	/* PCI controler 1 */
+#define CONFIG_PCIE1		1	/* PCIe 1 connected to ULI bridge */
+#define CONFIG_PCIE2		1	/* PCIe 2 connected to slot */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_SPD_EEPROM		/* Use SPD for DDR */
+#undef CONFIG_DDR_DLL			/* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
+
+#define CONFIG_ALTIVEC		1
+
+/*
+ * L2CR setup -- make sure this is right for your board!
+ */
+#define CFG_L2
+#define L2_INIT		0
+#define L2_ENABLE	(L2CR_L2E)
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST			/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00200000	/* memtest region */
+#define CFG_MEMTEST_END		0x00400000
+#define CFG_ALT_MEMTEST
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+#define CFG_PCI1_ADDR		(CFG_CCSRBAR+0x8000)
+#define CFG_PCIE1_ADDR		(CFG_CCSRBAR+0xa000)
+#define CFG_PCIE2_ADDR		(CFG_CCSRBAR+0x9000)
+
+#define CFG_DIU_ADDR		(CFG_CCSRBAR+0x2c000)
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define MPC86xx_DDR_SDRAM_CLK_CNTL
+
+#if defined(CONFIG_SPD_EEPROM)
+/*
+ * Determine DDR configuration from I2C interface.
+ */
+#define SPD_EEPROM_ADDRESS1		0x51		/* DDR DIMM */
+#else
+/*
+ * Manually set up DDR1 parameters
+ */
+
+#define CFG_SDRAM_SIZE	256		/* DDR is 256MB */
+
+#if 0 /* TODO */
+#define CFG_DDR_CS0_BNDS	0x0000000F
+#define CFG_DDR_CS0_CONFIG	0x80010202	/* Enable, no interleaving */
+#define CFG_DDR_EXT_REFRESH	0x00000000
+#define CFG_DDR_TIMING_0	0x00260802
+#define CFG_DDR_TIMING_1	0x3935d322
+#define CFG_DDR_TIMING_2	0x14904cc8
+#define CFG_DDR_MODE_1		0x00480432
+#define CFG_DDR_MODE_2		0x00000000
+#define CFG_DDR_INTERVAL	0x06180100
+#define CFG_DDR_DATA_INIT	0xdeadbeef
+#define CFG_DDR_CLK_CTRL	0x03800000
+#define CFG_DDR_OCD_CTRL	0x00000000
+#define CFG_DDR_OCD_STATUS	0x00000000
+#define CFG_DDR_CONTROL		0xe3008000	/* Type = DDR2 */
+#define CFG_DDR_CONTROL2	0x04400010
+
+#define CFG_DDR_ERR_INT_EN	0x00000000
+#define CFG_DDR_ERR_DIS		0x00000000
+#define CFG_DDR_SBE		0x000f0000
+ /* Not used in fixed_sdram function */
+#define CFG_DDR_MODE		0x00000022
+#define CFG_DDR_CS1_BNDS	0x00000000
+#define CFG_DDR_CS2_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS3_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS4_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS5_BNDS	0x00000FFF	/* Not done */
+#endif
+#endif
+
+#define CFG_ID_EEPROM
+#define ID_EEPROM_ADDR		0x57
+
+
+#define CFG_FLASH_BASE		0xf0000000 /* start of FLASH 128M */
+#define CFG_FLASH_BASE2		0xf8000000
+
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+
+#define CFG_BR0_PRELIM		0xf8001001 /* port size 16bit */
+#define CFG_OR0_PRELIM		0xf8006e65 /* 128MB NOR Flash*/
+
+#define CFG_BR1_PRELIM		0xf0001001 /* port size 16bit */
+#define CFG_OR1_PRELIM		0xf8006e65 /* 128MB Promjet */
+#if 0 /* TODO */
+#define CFG_BR2_PRELIM		0xf0000000
+#define CFG_OR2_PRELIM		0xf0000000 /* 256MB NAND Flash - bank 1 */
+#endif
+#define CFG_BR3_PRELIM		0xe8000801 /* port size 8bit */
+#define CFG_OR3_PRELIM		0xfff06ff7 /* 1MB PIXIS area*/
+
+
+#define PIXIS_BASE	0xe8000000	/* PIXIS registers */
+#define PIXIS_ID		0x0	/* Board ID at offset 0 */
+#define PIXIS_VER		0x1	/* Board version at offset 1 */
+#define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
+#define PIXIS_RST		0x4	/* PIXIS Reset Control register */
+#define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch */
+#define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
+#define PIXIS_VCTL		0x10	/* VELA Control Register */
+#define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
+#define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
+#define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
+#define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
+#define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
+#define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+
+#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
+#define CFG_MAX_FLASH_SECT	1024		/* sectors per device */
+
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef	CFG_RAMBOOT
+#endif
+
+#if defined(CFG_RAMBOOT)
+#undef CONFIG_SPD_EEPROM
+#define CFG_SDRAM_SIZE	256
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK	1
+#ifndef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
+#else
+#define CFG_INIT_RAM_ADDR	0xe4000000	/* Initial RAM address */
+#endif
+#define CFG_INIT_RAM_END	0x4000		/* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX	1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree to kernel
+ */
+#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE	8192
+
+#define OF_CPU		"PowerPC,8610@0"
+#define OF_SOC		"soc@e0000000"
+#define OF_TBCLK	(bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH	"/soc@e0000000/serial@4500"
+
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET		0x3000
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_IO_BASE	0x00000000
+#define CFG_PCI1_IO_PHYS	0xe1000000
+#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS	0x00000000
+#define CFG_PCI_MEMORY_PHYS	0x00000000
+#define CFG_PCI_MEMORY_SIZE	0x80000000
+
+/* For RTL8139 */
+#define KSEG1ADDR(x)	({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); })
+#define _IO_BASE		0x00000000
+
+/* controller 1, Base address 0xa000 */
+#define CFG_PCIE1_MEM_BASE	0xa0000000
+#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCIE1_IO_BASE	0x00000000
+#define CFG_PCIE1_IO_PHYS	0xe3000000
+#define CFG_PCIE1_IO_SIZE	0x00100000	/* 1M */
+
+/* controller 2, Base Address 0x9000 */
+#define CFG_PCIE2_MEM_BASE	0x90000000
+#define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
+#define CFG_PCIE2_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCIE2_IO_BASE	0x00000000	/* reuse mem LAW */
+#define CFG_PCIE2_IO_PHYS	0xe2000000
+#define CFG_PCIE2_IO_SIZE	0x00100000	/* 1M */
+
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+#if 0 /* TODO */
+/* enable onboard uli network support */
+#endif
+
+#define CONFIG_RTL8139
+#define CONFIG_SK98
+#define CONFIG_EEPRO100
+#define CONFIG_TULIP
+
+#if 0 /* TODO */
+/************************************************************
+ * USB support
+ ************************************************************/
+#define CONFIG_USB_OHCI		1
+#define CONFIG_USB_KEYBOARD	1
+#define CFG_DEVICE_DEREGISTER
+#define CFG_USB_INTERRUPT_POLL	1
+#endif
+
+#if !defined(CONFIG_PCI_PNP)
+#define PCI_ENET0_IOADDR	0xe0000000
+#define PCI_ENET0_MEMADDR	0xe0000000
+#define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
+#endif
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID	4
+#define CFG_SCSI_MAX_LUN	1
+#define CFG_SCSI_MAX_DEVICE	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
+#endif
+
+#endif	/* CONFIG_PCI */
+
+/*
+ * BAT0		2G	Cacheable, non-guarded
+ * 0x0000_0000	2G	DDR
+ */
+#define CFG_DBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U	(BATU_BL_2G | BATU_VS | BATU_VP)
+#define CFG_IBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CFG_IBAT0U	CFG_DBAT0U
+
+/*
+ * BAT1		1G	Cache-inhibited, guarded
+ * 0x8000_0000	256M	PCI-1 Memory
+ * 0xa000_0000	256M	PCI-Express 1 Memory
+ * 0x9000_0000	256M	PCI-Express 2 Memory
+ */
+
+#define CFG_DBAT1L	(CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+			| BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U	(CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
+#define CFG_IBAT1L	(CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U	CFG_DBAT1U
+
+/*
+ * BAT2		32M	Cache-inhibited, guarded
+ * 0xe100_0000	1M	PCI-1 I/O
+ * 0xe200_0000	1M	PCI-Express 2 I/O
+ *
+ */
+
+#define CFG_DBAT2L	(CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+			| BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U	(CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L	(CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U	CFG_DBAT2U
+
+/*
+ * BAT3		1M	Cache-inhibited, guarded
+ * 0xe300_0000	1M	PCI-Express 1 I/O
+ *
+ */
+
+#define CFG_DBAT3L	(CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+			| BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U	(CFG_PCIE1_IO_PHYS | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L	(CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U	CFG_DBAT3U
+
+/*
+ * BAT4		4M	Cache-inhibited, guarded
+ * 0xe000_0000	4M	CCSR
+ */
+#define CFG_DBAT4L	(CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
+			| BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U	(CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L	(CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U	CFG_DBAT4U
+
+/*
+ * BAT5		128K	Cacheable, non-guarded
+ * 0xe400_0000	128K	Init RAM for stack in the CPU DCache (no backing memory)
+ */
+#define CFG_DBAT5L	(CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT5U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_IBAT5L	CFG_DBAT5L
+#define CFG_IBAT5U	CFG_DBAT5U
+
+/*
+ * BAT6		256M	Cache-inhibited, guarded
+ * 0xf000_0000	256M	FLASH
+ */
+#define CFG_DBAT6L	(CFG_FLASH_BASE	 | BATL_PP_RW | BATL_CACHEINHIBIT \
+			| BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U	(CFG_FLASH_BASE	 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L	(CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U	CFG_DBAT6U
+
+/*
+ * BAT7		4M	Cache-inhibited, guarded
+ * 0xe800_0000	4M	PIXIS
+ */
+#define CFG_DBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
+			| BATL_GUARDEDSTORAGE)
+#define CFG_DBAT7U	(PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CFG_IBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT7U	CFG_DBAT7U
+
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CFG_ENV_SECT_SIZE	0x20000	/* 126k (one sector) for env */
+#define CFG_ENV_SIZE		0x2000
+#else
+#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+#define CFG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+
+#if defined(CFG_RAMBOOT)
+#undef CONFIG_CMD_ENV
+#endif
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_EXT2
+#endif
+
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE		32768
+#define CFG_CACHELINE_SIZE	32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_IPADDR		192.168.1.100
+
+#define CONFIG_HOSTNAME		unknown
+#define CONFIG_ROOTPATH		/opt/nfsroot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	8610hpcd/u-boot.bin
+
+#define CONFIG_SERVERIP		192.168.1.1
+#define CONFIG_GATEWAYIP	192.168.1.1
+#define CONFIG_NETMASK		255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#if defined(CONFIG_PCI1)
+#define PCI_ENV \
+ "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
+	"echo e;md ${a}e00 9\0" \
+ "pci1regs=setenv a e0008; run pcireg\0" \
+ "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
+	"pci d.w $b.0 56 1\0" \
+ "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
+	"pci w.w $b.0 56 ffff\0"	\
+ "pci1err=setenv a e0008; run pcierr\0"	\
+ "pci1errc=setenv a e0008; run pcierrc\0"
+#else
+#define	PCI_ENV ""
+#endif
+
+#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
+#define PCIE_ENV \
+ "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
+	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
+ "pcie1regs=setenv a e000a; run pciereg\0"	\
+ "pcie2regs=setenv a e0009; run pciereg\0"	\
+ "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
+	"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;"	\
+	"pci d $b.0 130 1\0" \
+ "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
+	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
+	"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0"		\
+ "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"	\
+ "pcie1err=setenv a e000a; run pcieerr\0"	\
+ "pcie2err=setenv a e0009; run pcieerr\0"	\
+ "pcie1errc=setenv a e000a; run pcieerrc\0"	\
+ "pcie2errc=setenv a e0009; run pcieerrc\0"
+#else
+#define	PCIE_ENV ""
+#endif
+
+#define DMA_ENV \
+ "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
+	"mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
+ "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
+	"mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
+ "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
+	"mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
+ "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
+	"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
+
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+ "netdev=eth0\0"						\
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+ "tftpflash=tftpboot $loadaddr $uboot; "			\
+	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+	"protect on " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+ "consoledev=ttyS0\0"						\
+ "ramdiskaddr=2000000\0"					\
+ "ramdiskfile=8610hpcd/ramdisk.uboot\0"				\
+ "dtbaddr=c00000\0"						\
+ "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0"				\
+ "bdev=sda3\0"					\
+ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
+ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+ "maxcpus=1"	\
+ "eoi=mw e00400b0 0\0"						\
+ "iack=md e00400a0 1\0"						\
+ "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
+	"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
+	"md ${a}f00 5\0" \
+ "ddr1regs=setenv a e0002; run ddrreg\0" \
+ "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
+	"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
+	"md ${a}e60 1; md ${a}ef0 1d\0" \
+ "guregs=setenv a e00e0; run gureg\0" \
+ "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
+ "mcmregs=setenv a e0001; run mcmreg\0" \
+ "diuregs=md e002c000 1d\0" \
+ "dium=mw e002c01c\0" \
+ "diuerr=md e002c014 1\0" \
+ "othbootargs=debug\0" \
+ "pmregs=md e00e1000 2b\0" \
+ "lawregs=md e0000c08 4b\0" \
+ "lbcregs=md e0005000 36\0" \
+ "dma0regs=md e0021100 12\0" \
+ "dma1regs=md e0021180 12\0" \
+ "dma2regs=md e0021200 12\0" \
+ "dma3regs=md e0021280 12\0" \
+ PCI_ENV \
+ PCIE_ENV \
+ DMA_ENV
+
+#define CONFIG_NFSBOOTCOMMAND					\
+ "setenv bootargs root=/dev/nfs rw "				\
+	"nfsroot=$serverip:$rootpath "				\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"		\
+ "tftp $loadaddr $bootfile;"					\
+ "tftp $dtbaddr $dtbfile;"					\
+ "bootm $loadaddr - $dtbaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw "				\
+	"console=$consoledev,$baudrate $othbootargs;"		\
+ "tftp $ramdiskaddr $ramdiskfile;"				\
+ "tftp $loadaddr $bootfile;"					\
+ "tftp $dtbaddr $dtbfile;"					\
+ "bootm $loadaddr $ramdiskaddr $dtbaddr"
+
+#define CONFIG_BOOTCOMMAND		\
+ "setenv bootargs root=/dev/$bdev rw "	\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $dtbaddr $dtbfile;"		\
+ "bootm $loadaddr - $dtbaddr"
+
+#endif	/* __CONFIG_H */
-- 
cgit v1.1


From 20d500d531a6b971ce6cc1bf191cb0092cdc0afc Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Tue, 23 Oct 2007 10:17:42 +0200
Subject: ppc4xx: lwmon5: Some further GPIO config changes

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/lwmon5.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index 00c34d5..52deab4 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -432,7 +432,7 @@
 {GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12				*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO13				*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO15				*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO15				*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMCTxD(4)			*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMCTxD(5)			*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMCTxD(6)			*/	\
@@ -473,7 +473,7 @@
 {GPIO1_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO50  Unselect via TraceSelect Bit	*/	\
 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51  Unselect via TraceSelect Bit	*/	\
 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52  Unselect via TraceSelect Bit	*/	\
-{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO53  Unselect via TraceSelect Bit	*/	\
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO53  Unselect via TraceSelect Bit	*/	\
 {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO54  Unselect via TraceSelect Bit	*/	\
 {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55  Unselect via TraceSelect Bit	*/	\
 {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO56  Unselect via TraceSelect Bit	*/	\
-- 
cgit v1.1


From 4dbee8a90df613eb517aadbecebd70f168913d30 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Fri, 5 Oct 2007 07:57:20 +0200
Subject: ppc4xx: 4xx_pcie: Change CFG_PCIE_MEMSIZE to 128MB on Yucca & Katmai

128MB seems to be the smallest possible value for the memory size
for on PCIe port. With this change now the BAR's of the PCIe cards
are accessible under U-Boot.

One big note: This only works for PCIe port 0 & 1. For port 2 this
currently doesn't work, since the base address is now 0xc0000000
(0xb0000000 + 2 * 0x08000000), and this is already occupied by
CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean
to change the base addresses completely and this change would have
too much impact right now.

This patch adds debug output to the 4xx pcie driver too.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/katmai.h | 2 +-
 include/configs/yucca.h  | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 7908e5a..03c3cb3 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -62,7 +62,7 @@
 #define CFG_PCI_TARGBASE	CFG_PCI_MEMBASE
 
 #define CFG_PCIE_MEMBASE	0xb0000000	/* mapped PCIe memory	*/
-#define CFG_PCIE_MEMSIZE	0x01000000
+#define CFG_PCIE_MEMSIZE	0x08000000	/* smallest incr for PCIe port */
 #define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */
 
 #define CFG_PCIE0_CFGBASE	0xc0000000
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 74033b4..6caf21b 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -64,7 +64,7 @@
 #define CFG_PCI_TARGBASE	CFG_PCI_MEMBASE
 
 #define CFG_PCIE_MEMBASE	0xb0000000	/* mapped PCIe memory	*/
-#define CFG_PCIE_MEMSIZE	0x01000000
+#define CFG_PCIE_MEMSIZE	0x08000000	/* smallest incr for PCIe port */
 #define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */
 
 #define CFG_PCIE0_CFGBASE	0xc0000000
-- 
cgit v1.1


From 97923770cb52b64d69eec958a11b2eda8d46e0f7 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Fri, 5 Oct 2007 09:18:23 +0200
Subject: ppc4xx: 4xx_pcie: More general cleanup and 405EX PCIe support added

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/katmai.h | 3 +++
 include/configs/yucca.h  | 3 +++
 2 files changed, 6 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 03c3cb3..8a96327 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -72,6 +72,9 @@
 #define CFG_PCIE1_XCFGBASE	0xc3001000
 #define CFG_PCIE2_XCFGBASE	0xc3002000
 
+/* base address of inbound PCIe window */
+#define CFG_PCIE_INBOUND_BASE	0x0000000400000000ULL
+
 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
 #define CONFIG_PCI_SYS_MEM_PHYS	CFG_SDRAM_BASE
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 6caf21b..ab7fb0a 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -74,6 +74,9 @@
 #define CFG_PCIE1_XCFGBASE	0xc3001000
 #define CFG_PCIE2_XCFGBASE	0xc3002000
 
+/* base address of inbound PCIe window */
+#define CFG_PCIE_INBOUND_BASE	0x0000000400000000ULL
+
 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
 #define CONFIG_PCI_SYS_MEM_PHYS	CFG_SDRAM_BASE
-- 
cgit v1.1


From 4f2e92c11f6e2392fc8187829211a5ca7f0c1e12 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Fri, 5 Oct 2007 15:10:02 +0200
Subject: DTT: Prepare DS1775 driver for use of different I2C addresses

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/taihu.h | 1 +
 1 file changed, 1 insertion(+)

(limited to 'include/configs')

diff --git a/include/configs/taihu.h b/include/configs/taihu.h
index d623e56..6d204a9 100644
--- a/include/configs/taihu.h
+++ b/include/configs/taihu.h
@@ -244,6 +244,7 @@ unsigned char spi_read(void);
 /* standard dtt sensor configuration */
 #define CONFIG_DTT_DS1775	1
 #define CONFIG_DTT_SENSORS	{ 0 }
+#define CFG_I2C_DTT_ADDR	0x49
 
 /*-----------------------------------------------------------------------
  * PCI stuff
-- 
cgit v1.1


From 566806ca1a1bf4d895daaf0b2ba5494abbffebaf Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Fri, 5 Oct 2007 17:11:30 +0200
Subject: ppc4xx: Add initial AMCC Kilauea 405EX support

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 486 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 486 insertions(+)
 create mode 100644 include/configs/kilauea.h

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
new file mode 100644
index 0000000..7858f83
--- /dev/null
+++ b/include/configs/kilauea.h
@@ -0,0 +1,486 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * kilauea.h - configuration for AMCC Kilauea (405EX)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_KILAUEA		1		/* Board is Kilauea	*/
+#define CONFIG_4xx		1		/* ... PPC4xx family	*/
+#define CONFIG_405EX		1		/* Specifc 405EX support*/
+#define CONFIG_SYS_CLK_FREQ	33333333	/* ext frequency to pll	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFC000000
+#define CFG_NAND_ADDR		0xF8000000
+#define CFG_FPGA_BASE		0xF0000000
+#define CFG_PERIPHERAL_BASE	0xEF600000      /* internal peripherals*/
+#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MONITOR_BASE	(TEXT_BASE)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+#define CFG_INIT_RAM_ADDR	0x02000000	/* inside of SDRAM	*/
+#define CFG_INIT_RAM_END	(4 << 10)
+#define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+/* reserve some memory for POST and BOOT limit info */
+#define CFG_INIT_SP_OFFSET	(CFG_GBL_DATA_OFFSET - 16)
+
+/* extra data in init-ram */
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 4)
+#define CFG_POST_MAGIC		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
+#define CFG_POST_VAL		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
+#define CFG_OCM_DATA_ADDR	CFG_INIT_RAM_ADDR /* for commproc.c	*/
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CFG_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI     1
+/* define this if you want console on UART1 */
+#undef CONFIG_UART1_CONSOLE
+
+#define CFG_BAUDRATE_TABLE						\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+#else
+#define CFG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
+#define CFG_ENV_IS_EMBEDDED	1	/* use embedded environment */
+#endif
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI			/* The flash is CFI compatible	*/
+#define CFG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/
+
+#define CFG_FLASH_BANKS_LIST    {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x20000 	/* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif /* CFG_ENV_IS_IN_FLASH */
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM        (256)		/* 256MB			*/
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
+#define CFG_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+
+/* Standard DTT sensor configuration */
+#define CONFIG_DTT_DS1775	1
+#define CONFIG_DTT_SENSORS	{ 0 }
+#define CFG_I2C_DTT_ADDR	0x48
+
+/* RTC configuration */
+#define CONFIG_RTC_DS1338	1
+#define CFG_I2C_RTC_ADDR	0x68
+
+/*-----------------------------------------------------------------------
+ * Ethernet
+ *----------------------------------------------------------------------*/
+#define CONFIG_M88E1111_PHY	1
+#define CONFIG_IBM_EMAC4_V4	1
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
+
+#define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0		1
+
+#define CONFIG_NET_MULTI	1
+#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
+#define CONFIG_PHY1_ADDR	2
+
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#undef USE_LIBFDT
+#ifdef USE_LIBFDT
+/*
+ * LIBFDT support is disabled for now since first Linux port is still
+ * arch/ppc.
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"logversion=2\0"						\
+	"netdev=eth0\0"							\
+	"hostname=kilauea\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"net_nfs=tftp 200000 ${bootfile};"				\
+		"tftp ${fdt_addr} ${fdt_file};"				\
+		"run nfsargs addip addtty;"				\
+		"bootm 200000 - ${fdt_addr}\0"				\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"rootpath=/opt/eldk/ppc_4xx\0"					\
+	"bootfile=kilauea/uImage\0"					\
+	"fdt_file=kilauea/kilauea.dtb\0"				\
+	"fdt_addr=400000\0"						\
+	"kernel_addr=fc000000\0"					\
+	"ramdisk_addr=fc200000\0"					\
+	"initrd_high=30000000\0"					\
+	"load=tftp 200000 kilauea/u-boot.bin\0"				\
+	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
+		"cp.b ${fileaddr} fffa0000 ${filesize};"		\
+		"setenv filesize;saveenv\0"				\
+	"upd=run load update\0"						\
+	"nload=tftp 200000 kilauea/u-boot-nand.bin\0"			\
+	"nupdate=nand erase 0 60000;nand write 200000 0 60000;"		\
+		"setenv filesize;saveenv\0"				\
+	"nupd=run nload nupdate\0"					\
+	""
+#else
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"logversion=2\0"						\
+	"netdev=eth0\0"							\
+	"hostname=kilauea\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"net_nfs=tftp 200000 ${bootfile};"				\
+		"run nfsargs addip addtty;"				\
+		"bootm 200000\0"					\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"rootpath=/opt/eldk/ppc_4xx\0"					\
+	"bootfile=kilauea/uImage\0"					\
+	"kernel_addr=fc000000\0"					\
+	"ramdisk_addr=fc200000\0"					\
+	"initrd_high=30000000\0"					\
+	"load=tftp 200000 kilauea/u-boot.bin\0"				\
+	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
+		"cp.b ${fileaddr} fffa0000 ${filesize};"		\
+		"setenv filesize;saveenv\0"				\
+	"upd=run load update\0"						\
+	"nload=tftp 200000 kilauea/u-boot-nand.bin\0"			\
+	"nupdate=nand erase 0 60000;nand write 200000 0 60000;"		\
+		"setenv filesize;saveenv\0"				\
+	"nupd=run nload nupdate\0"					\
+	"pciconfighost=1\0"						\
+	""
+#endif
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE		/* allow baudrate change	*/
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_LOG
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+/* POST support */
+#define CONFIG_POST		(CFG_POST_MEMORY	| \
+				 CFG_POST_CACHE		| \
+				 CFG_POST_CPU		| \
+				 CFG_POST_ETHER		| \
+				 CFG_POST_I2C		| \
+				 CFG_POST_MEMORY	| \
+				 CFG_POST_UART)
+
+/* Define here the base-addresses of the UARTs to test in POST */
+#define CFG_POST_UART_TABLE	{UART0_BASE, UART1_BASE}
+
+#define CONFIG_LOGBUFFER
+#define CFG_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/
+
+#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE
+
+/*-----------------------------------------------------------------------
+ * PCIe stuff
+ *----------------------------------------------------------------------*/
+#define CFG_PCIE_MEMBASE	0x90000000	/* mapped PCIe memory	*/
+#define CFG_PCIE_MEMSIZE	0x08000000      /* 128 Meg, smallest incr per port */
+
+#define	CFG_PCIE0_CFGBASE	0xa0000000      /* remote access */
+#define	CFG_PCIE0_XCFGBASE	0xb0000000      /* local access */
+#define	CFG_PCIE0_CFGMASK	0xe0000001      /* 512 Meg */
+
+#define	CFG_PCIE1_CFGBASE	0xc0000000      /* remote access */
+#define	CFG_PCIE1_XCFGBASE	0xd0000000      /* local access */
+#define	CFG_PCIE1_CFGMASK	0xe0000001      /* 512 Meg */
+
+#define	CFG_PCIE0_UTLBASE	0xef502000
+#define	CFG_PCIE1_UTLBASE	0xef503000
+
+/* base address of inbound PCIe window */
+#define CFG_PCIE_INBOUND_BASE	0x0000000000000000ULL
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *----------------------------------------------------------------------*/
+#define CFG_DCACHE_SIZE		(16 << 10) /* For IBM 405EX			*/
+#define CFG_CACHELINE_SIZE	32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+#define CFG_NAND_CS		1		/* NAND chip connected to CSx	*/
+
+/* Memory Bank 0 (NOR-FLASH) initialization					*/
+#define CFG_EBC_PB0AP		0x05806500
+#define CFG_EBC_PB0CR           0xFC0DA000  /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 1 (NAND-FLASH) initialization					*/
+#define CFG_EBC_PB1AP		0x018003c0
+#define CFG_EBC_PB1CR		(CFG_NAND_ADDR | 0x1e000)
+
+/* Memory Bank 2 (FPGA) initialization						*/
+#define CFG_EBC_PB2AP           0x9400C800
+#define CFG_EBC_PB2CR           0xF0018000 /*  BAS=0x800,BS=1MB,BU=R/W,BW=8bit	*/
+
+#define CFG_EBC_CFG		0x7FC00000 /*  EBC0_CFG */
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS		1
+#define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
+
+/*-----------------------------------------------------------------------
+ * GPIO Setup
+ *----------------------------------------------------------------------*/
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EX specific)
+ *
+ * GPIO0[0-3]      - EBC data 0-3	inputs/outputs
+ * GPIO0[4-7]      - USB data 4-7	inputs/outputs
+ * GPIO0[8-11]     - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
+ * GPIO0[12-15]    - USB data 0-3	inputs/outputs
+ * GPIO0[16-21]    - UART0 control signal inputs/outputs
+ *
+ * GPIO0[22-25,27] - EBC control signal inputs/outputs
+ * GPIO0[26]	   - Instruction trace outputs
+ * GPIO0[28]	   - Float, N/C
+ * GPIO0[29-31]    - DMA control signal inputs/outputs
+ */
+#define CFG_GPIO0_OSRL		0x00AA54AA
+#define CFG_GPIO0_OSRH		0x21800000
+#define CFG_GPIO0_TSRL		0x00AA55AA
+#define CFG_GPIO0_TSRH		0xA5A00000
+
+#define CFG_GPIO0_ISR1L		0x00000100
+#define CFG_GPIO0_ISR1H		0x04000000
+#define CFG_GPIO0_ISR2L		0x00550055
+#define CFG_GPIO0_ISR2H		0x40100000
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Some Kilauea stuff..., mainly fpga registers
+ */
+#define CFG_FPGA_REG_BASE		CFG_FPGA_BASE
+#define CFG_FPGA_FIFO_BASE		(in32(CFG_FPGA_BASE) | (1 << 11))
+
+/* interrupt */
+#define CFG_FPGA_SLIC0_R_DPRAM_INT	0x80000000
+#define CFG_FPGA_SLIC0_W_DPRAM_INT	0x40000000
+#define CFG_FPGA_SLIC1_R_DPRAM_INT	0x20000000
+#define CFG_FPGA_SLIC1_W_DPRAM_INT	0x10000000
+#define CFG_FPGA_PHY0_INT		0x08000000
+#define CFG_FPGA_PHY1_INT		0x04000000
+#define CFG_FPGA_SLIC0_INT		0x02000000
+#define CFG_FPGA_SLIC1_INT		0x01000000
+
+/* DPRAM setting */
+/* 00: 32B; 01: 64B; 10: 128B; 11: 256B  */
+#define CFG_FPGA_DPRAM_R_INT_LINE	0x00400000	/* 64 B */
+#define CFG_FPGA_DPRAM_W_INT_LINE	0x00100000	/* 64 B */
+#define CFG_FPGA_DPRAM_RW_TYPE		0x00080000
+#define CFG_FPGA_DPRAM_RST		0x00040000
+#define CFG_FPGA_UART0_FO		0x00020000
+#define CFG_FPGA_UART1_FO		0x00010000
+
+/* loopback */
+#define CFG_FPGA_CHIPSIDE_LOOPBACK	0x00004000
+#define CFG_FPGA_LINESIDE_LOOPBACK	0x00008000
+#define CFG_FPGA_SLIC0_ENABLE		0x00002000
+#define CFG_FPGA_SLIC1_ENABLE		0x00001000
+#define CFG_FPGA_SLIC0_CS		0x00000800
+#define CFG_FPGA_SLIC1_CS		0x00000400
+#define CFG_FPGA_USER_LED0		0x00000200
+#define CFG_FPGA_USER_LED1		0x00000100
+
+#endif	/* __CONFIG_H */
+
+#ifdef USE_LIBFDT
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+#define OF_CPU			"PowerPC,405EX@0"
+#endif
-- 
cgit v1.1


From fd671802b67a0ef37a06124fa2ce85f00aa22c6f Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Thu, 11 Oct 2007 11:15:59 +0200
Subject: ppc4xx: Enable device tree support (fdt) on Kilauea per default

This patch enables the fdt support on the AMCC Kilauea eval board.
Additionally now EBC ranges fdt fixup is included to support NOR
FLASH mapping via the Linux physmap_of driver.

This Kilauea port now support booting arch/ppc and arch/powerpc
Linux kernels. The default environment "net_nfs" is for arch/ppc
and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc
support will be removed.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 46 +++-------------------------------------------
 1 file changed, 3 insertions(+), 43 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 7858f83..461f8f0 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -166,12 +166,6 @@
 
 #undef	CONFIG_BOOTARGS
 
-#undef USE_LIBFDT
-#ifdef USE_LIBFDT
-/*
- * LIBFDT support is disabled for now since first Linux port is still
- * arch/ppc.
- */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"logversion=2\0"						\
 	"netdev=eth0\0"							\
@@ -184,6 +178,9 @@
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 	"net_nfs=tftp 200000 ${bootfile};"				\
+		"run nfsargs addip addtty;"				\
+		"bootm 200000\0"					\
+	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
 		"tftp ${fdt_addr} ${fdt_file};"				\
 		"run nfsargs addip addtty;"				\
 		"bootm 200000 - ${fdt_addr}\0"				\
@@ -207,43 +204,8 @@
 	"nupdate=nand erase 0 60000;nand write 200000 0 60000;"		\
 		"setenv filesize;saveenv\0"				\
 	"nupd=run nload nupdate\0"					\
-	""
-#else
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"logversion=2\0"						\
-	"netdev=eth0\0"							\
-	"hostname=kilauea\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"net_nfs=tftp 200000 ${bootfile};"				\
-		"run nfsargs addip addtty;"				\
-		"bootm 200000\0"					\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=kilauea/uImage\0"					\
-	"kernel_addr=fc000000\0"					\
-	"ramdisk_addr=fc200000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 200000 kilauea/u-boot.bin\0"				\
-	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
-		"cp.b ${fileaddr} fffa0000 ${filesize};"		\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
-	"nload=tftp 200000 kilauea/u-boot-nand.bin\0"			\
-	"nupdate=nand erase 0 60000;nand write 200000 0 60000;"		\
-		"setenv filesize;saveenv\0"				\
-	"nupd=run nload nupdate\0"					\
 	"pciconfighost=1\0"						\
 	""
-#endif
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
@@ -477,10 +439,8 @@
 
 #endif	/* __CONFIG_H */
 
-#ifdef USE_LIBFDT
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
 #define OF_CPU			"PowerPC,405EX@0"
-#endif
-- 
cgit v1.1


From d4cb2d17946466740afeb195a57d6cb290bf4cc0 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Sat, 13 Oct 2007 16:43:23 +0200
Subject: ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint
 mode

This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.

This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:

pcie_mode=RP:EP:EP

This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.

Per default Yucca will be configured as:
pcie_mode=RP:EP:EP

Per default Katmai will be configured as:
pcie_mode=RP:RP:REP

Per default Kilauea will be configured as:
pcie_mode=RP:RP

Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/katmai.h  | 1 +
 include/configs/kilauea.h | 1 +
 include/configs/yucca.h   | 1 +
 3 files changed, 3 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 8a96327..cccfc13 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -205,6 +205,7 @@
 	"upd=run load;run update\0"					\
 	"kozio=bootm ffc60000\0"					\
 	"pciconfighost=1\0"						\
+	"pcie_mode=RP:RP:RP\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 461f8f0..f5e2023 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -205,6 +205,7 @@
 		"setenv filesize;saveenv\0"				\
 	"nupd=run nload nupdate\0"					\
 	"pciconfighost=1\0"						\
+	"pcie_mode=RP:RP\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index ab7fb0a..2b4024d 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -186,6 +186,7 @@
 		"setenv filesize;saveenv\0"				\
 	"upd=run load;run update\0"					\
 	"pciconfighost=1\0"						\
+	"pcie_mode=RP:EP:EP\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
-- 
cgit v1.1


From c36c68160333ac5fe41ec3db12a728b7075b3912 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Thu, 18 Oct 2007 07:42:27 +0200
Subject: ppc4xx: Change inbound PCIe location for endpoint tests on Katmai

On Yucca & Katmai, the inbound memory map pointed to 0x4.0000.0000, which
is the internal SRAM. Since I now ported and tested this endpoint mode
on Kilauea successfully to map to 0 (SDRAM), I also changed this for
Katmai.

Yucca will stay at internal SRAM for now. Not sure if somebody relies on
this setup.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/katmai.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index cccfc13..6bc8d02 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -73,7 +73,7 @@
 #define CFG_PCIE2_XCFGBASE	0xc3002000
 
 /* base address of inbound PCIe window */
-#define CFG_PCIE_INBOUND_BASE	0x0000000400000000ULL
+#define CFG_PCIE_INBOUND_BASE	0x0000000000000000ULL
 
 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
-- 
cgit v1.1


From 837c730b4d7c6b1ddf3d1e247cb4445005d9bf0d Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Sun, 21 Oct 2007 14:26:29 +0200
Subject: ppc: Small Kilauea cleanup of config file

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index f5e2023..74c9483 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -438,10 +438,10 @@
 #define CFG_FPGA_USER_LED0		0x00000200
 #define CFG_FPGA_USER_LED1		0x00000100
 
-#endif	/* __CONFIG_H */
-
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
 #define OF_CPU			"PowerPC,405EX@0"
+
+#endif	/* __CONFIG_H */
-- 
cgit v1.1


From 211ea91ac6c225bec7e668a03d0ba7d7310679fa Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Mon, 22 Oct 2007 07:34:34 +0200
Subject: ppc4xx: Add initial AMCC Makalu 405EX support

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/makalu.h | 387 +++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 387 insertions(+)
 create mode 100644 include/configs/makalu.h

(limited to 'include/configs')

diff --git a/include/configs/makalu.h b/include/configs/makalu.h
new file mode 100644
index 0000000..6c4d0b6
--- /dev/null
+++ b/include/configs/makalu.h
@@ -0,0 +1,387 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * makalu.h - configuration for AMCC Makalu (405EX)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_MAKALU		1		/* Board is Makalu	*/
+#define CONFIG_4xx		1		/* ... PPC4xx family	*/
+#define CONFIG_405EX		1		/* Specifc 405EX support*/
+#define CONFIG_SYS_CLK_FREQ	33330000	/* ext frequency to pll	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFE000000
+#define CFG_FPGA_BASE		0xF0000000
+#define CFG_PERIPHERAL_BASE	0xEF600000      /* internal peripherals*/
+#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MONITOR_BASE	(TEXT_BASE)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+#define CFG_INIT_RAM_ADDR	0x02000000	/* inside of SDRAM	*/
+#define CFG_INIT_RAM_END	(4 << 10)
+#define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+/* reserve some memory for POST and BOOT limit info */
+#define CFG_INIT_SP_OFFSET	(CFG_GBL_DATA_OFFSET - 16)
+
+/* extra data in init-ram */
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 4)
+#define CFG_POST_MAGIC		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
+#define CFG_POST_VAL		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
+#define CFG_OCM_DATA_ADDR	CFG_INIT_RAM_ADDR /* for commproc.c	*/
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CFG_EXT_SERIAL_CLOCK			/* no ext. clk		*/
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI     1
+/* define this if you want console on UART1 */
+#undef CONFIG_UART1_CONSOLE
+
+#define CFG_BAUDRATE_TABLE						\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI			/* The flash is CFI compatible	*/
+#define CFG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/
+
+#define CFG_FLASH_BANKS_LIST    {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x20000 	/* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif /* CFG_ENV_IS_IN_FLASH */
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM        128
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
+#define CFG_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+
+/* Standard DTT sensor configuration */
+#define CONFIG_DTT_DS1775	1
+#define CONFIG_DTT_SENSORS	{ 0 }
+#define CFG_I2C_DTT_ADDR	0x48
+
+/* RTC configuration */
+#define CONFIG_RTC_X1205	1
+#define CFG_I2C_RTC_ADDR	0x6f
+
+/*-----------------------------------------------------------------------
+ * Ethernet
+ *----------------------------------------------------------------------*/
+#define CONFIG_M88E1111_PHY	1
+#define CONFIG_IBM_EMAC4_V4	1
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		6	/* PHY address, See schematics	*/
+
+#define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0		1
+
+#define CONFIG_NET_MULTI	1
+#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
+#define CONFIG_PHY1_ADDR	2
+
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"logversion=2\0"						\
+	"netdev=eth0\0"							\
+	"hostname=makalu\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"	\
+	"net_nfs=tftp 200000 ${bootfile};"				\
+		"run nfsargs addip addtty addmisc;"			\
+		"bootm 200000\0"					\
+	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
+		"tftp ${fdt_addr} ${fdt_file};"				\
+		"run nfsargs addip addtty addmisc;"			\
+		"bootm 200000 - ${fdt_addr}\0"				\
+	"flash_nfs=run nfsargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"rootpath=/opt/eldk/ppc_4xx\0"					\
+	"bootfile=makalu/uImage\0"					\
+	"fdt_file=makalu/makalu.dtb\0"					\
+	"fdt_addr=400000\0"						\
+	"kernel_addr=fe000000\0"					\
+	"ramdisk_addr=fe200000\0"					\
+	"initrd_high=30000000\0"					\
+	"load=tftp 200000 makalu/u-boot.bin\0"				\
+	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
+		"cp.b ${fileaddr} fffa0000 ${filesize};"		\
+		"setenv filesize;saveenv\0"				\
+	"upd=run load update\0"						\
+	"pciconfighost=1\0"						\
+	"pcie_mode=RP:RP\0"						\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE		/* allow baudrate change	*/
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_LOG
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+/* POST support */
+#define CONFIG_POST		(CFG_POST_MEMORY	| \
+				 CFG_POST_CACHE		| \
+				 CFG_POST_CPU		| \
+				 CFG_POST_ETHER		| \
+				 CFG_POST_I2C		| \
+				 CFG_POST_MEMORY	| \
+				 CFG_POST_UART)
+
+/* Define here the base-addresses of the UARTs to test in POST */
+#define CFG_POST_UART_TABLE	{UART0_BASE, UART1_BASE}
+
+#define CONFIG_LOGBUFFER
+#define CFG_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/
+
+#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE
+
+/*-----------------------------------------------------------------------
+ * PCIe stuff
+ *----------------------------------------------------------------------*/
+#define CFG_PCIE_MEMBASE	0x90000000	/* mapped PCIe memory	*/
+#define CFG_PCIE_MEMSIZE	0x08000000      /* 128 Meg, smallest incr per port */
+
+#define	CFG_PCIE0_CFGBASE	0xa0000000      /* remote access */
+#define	CFG_PCIE0_XCFGBASE	0xb0000000      /* local access */
+#define	CFG_PCIE0_CFGMASK	0xe0000001      /* 512 Meg */
+
+#define	CFG_PCIE1_CFGBASE	0xc0000000      /* remote access */
+#define	CFG_PCIE1_XCFGBASE	0xd0000000      /* local access */
+#define	CFG_PCIE1_CFGMASK	0xe0000001      /* 512 Meg */
+
+#define	CFG_PCIE0_UTLBASE	0xef502000
+#define	CFG_PCIE1_UTLBASE	0xef503000
+
+/* base address of inbound PCIe window */
+#define CFG_PCIE_INBOUND_BASE	0x0000000000000000ULL
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *----------------------------------------------------------------------*/
+#define CFG_DCACHE_SIZE		(16 << 10) /* For IBM 405EX			*/
+#define CFG_CACHELINE_SIZE	32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+/* Memory Bank 0 (NOR-FLASH) initialization					*/
+#define CFG_EBC_PB0AP		0x04011000
+#define CFG_EBC_PB0CR           0xFE0BA000  /* BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 2 (CPLD) initialization						*/
+#define CFG_EBC_PB2AP           0x9400C800
+#define CFG_EBC_PB2CR           0xF0018000 /*  BAS=0x800,BS=1MB,BU=R/W,BW=8bit	*/
+
+#define CFG_EBC_CFG		0x7FC00000 /*  EBC0_CFG */
+
+/*-----------------------------------------------------------------------
+ * GPIO Setup
+ *----------------------------------------------------------------------*/
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EX specific)
+ *
+ * GPIO0[0-3]      - EBC data 0-3	inputs/outputs
+ * GPIO0[4-7]      - USB data 4-7	inputs/outputs
+ * GPIO0[8-11]     - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
+ * GPIO0[12-15]    - USB data 0-3	inputs/outputs
+ * GPIO0[16-21]    - UART0 control signal inputs/outputs
+ *
+ * GPIO0[22-25,27] - EBC control signal inputs/outputs
+ * GPIO0[26]	   - Instruction trace outputs
+ * GPIO0[28]	   - Float, N/C
+ * GPIO0[29-31]    - DMA control signal inputs/outputs
+ */
+#define CFG_GPIO0_OSRL		0x00AA54AA
+#define CFG_GPIO0_OSRH		0x55500000
+#define CFG_GPIO0_TSRL		0x00AA54AA
+#define CFG_GPIO0_TSRH		0x55500000
+#define CFG_GPIO0_ISR1L		0x00005400
+#define CFG_GPIO0_ISR1H		0x55500000
+#define CFG_GPIO0_ISR2L		0x00550055
+#define CFG_GPIO0_ISR2H		0x00000000
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+#define OF_CPU			"PowerPC,405EX@0"
+
+#endif	/* __CONFIG_H */
-- 
cgit v1.1


From afe9fa59cb63b4f9d16bf01c93eb212f25a38c2a Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Mon, 22 Oct 2007 16:24:44 +0200
Subject: ppc4xx: Add SNTP support to AMCC Katmai, Kilauea & Makalu boards

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/katmai.h  | 2 +-
 include/configs/kilauea.h | 1 +
 include/configs/makalu.h  | 1 +
 3 files changed, 3 insertions(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 6bc8d02..5da00fc 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -247,7 +247,7 @@
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
-
+#define CONFIG_CMD_SNTP
 
 #define	CONFIG_IBM_EMAC4_V4	1	/* 440SPe has this EMAC version	*/
 #define CONFIG_MII		1	/* MII PHY management		*/
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 74c9483..90bdd69 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -244,6 +244,7 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
 
 /* POST support */
 #define CONFIG_POST		(CFG_POST_MEMORY	| \
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index 6c4d0b6..3e3b008 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -234,6 +234,7 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
 
 /* POST support */
 #define CONFIG_POST		(CFG_POST_MEMORY	| \
-- 
cgit v1.1


From 353f2688b4e0fc7b969bc70a02be4b40bf0dd124 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Tue, 23 Oct 2007 10:10:08 +0200
Subject: ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board support

The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 1 +
 1 file changed, 1 insertion(+)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 90bdd69..9a9f7ba 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -38,6 +38,7 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
 #define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
+#define CONFIG_BOARD_EMAC_COUNT
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
-- 
cgit v1.1


From d25dfe08fbd1220cb994e7e6b105049aa9aa8e79 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Wed, 31 Oct 2007 17:57:52 +0100
Subject: ppc4xx: Remove cache definition from 4xx board config files

All 4xx board config files don't need the cache definitions anymore.
These are now defined in common headers.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/ADCIOP.h         |  9 ---------
 include/configs/AP1000.h         |  8 --------
 include/configs/AR405.h          | 10 ----------
 include/configs/ASH405.h         | 10 ----------
 include/configs/CANBT.h          |  9 ---------
 include/configs/CMS700.h         | 10 ----------
 include/configs/CPCI2DP.h        | 10 ----------
 include/configs/CPCI405.h        |  9 ---------
 include/configs/CPCI4052.h       | 10 ----------
 include/configs/CPCI405AB.h      | 10 ----------
 include/configs/CPCI405DT.h      | 10 ----------
 include/configs/CPCI440.h        |  9 ---------
 include/configs/CPCIISER4.h      |  9 ---------
 include/configs/CRAYL1.h         |  6 ------
 include/configs/DASA_SIM.h       |  9 ---------
 include/configs/DP405.h          | 10 ----------
 include/configs/DU405.h          |  9 ---------
 include/configs/ERIC.h           |  8 --------
 include/configs/EXBITGEN.h       |  4 ----
 include/configs/G2000.h          | 10 ----------
 include/configs/HH405.h          | 10 ----------
 include/configs/HUB405.h         | 10 ----------
 include/configs/JSE.h            |  9 ---------
 include/configs/KAREF.h          |  8 --------
 include/configs/METROBOX.h       |  8 --------
 include/configs/MIP405.h         |  9 ---------
 include/configs/ML2.h            |  8 --------
 include/configs/OCRTC.h          |  9 ---------
 include/configs/ORSG.h           |  9 ---------
 include/configs/PCI405.h         |  9 ---------
 include/configs/PIP405.h         |  9 ---------
 include/configs/PLU405.h         | 10 ----------
 include/configs/PMC405.h         | 10 ----------
 include/configs/PPChameleonEVB.h | 10 ----------
 include/configs/VOH405.h         | 10 ----------
 include/configs/VOM405.h         | 10 ----------
 include/configs/W7OLMC.h         |  9 ---------
 include/configs/W7OLMG.h         |  9 ---------
 include/configs/WUH405.h         | 10 ----------
 include/configs/XPEDITE1K.h      |  8 --------
 include/configs/acadia.h         |  9 ---------
 include/configs/alpr.h           |  6 ------
 include/configs/bamboo.h         |  9 ---------
 include/configs/bubinga.h        |  8 --------
 include/configs/csb272.h         |  8 --------
 include/configs/csb472.h         |  8 --------
 include/configs/ebony.h          |  8 --------
 include/configs/hcu4.h           |  7 -------
 include/configs/hcu5.h           |  7 -------
 include/configs/katmai.h         |  8 --------
 include/configs/kilauea.h        |  9 ---------
 include/configs/luan.h           |  9 ---------
 include/configs/lwmon5.h         |  9 ---------
 include/configs/makalu.h         |  9 ---------
 include/configs/ml300.h          |  6 ------
 include/configs/ocotea.h         |  8 --------
 include/configs/p3p440.h         |  8 --------
 include/configs/pcs440ep.h       |  9 ---------
 include/configs/sbc405.h         | 10 ----------
 include/configs/sc3.h            | 18 ------------------
 include/configs/sequoia.h        | 17 ++++++++---------
 include/configs/taihu.h          |  7 -------
 include/configs/taishan.h        |  9 ---------
 include/configs/walnut.h         | 10 ----------
 include/configs/yosemite.h       |  9 ---------
 include/configs/yucca.h          |  8 --------
 include/configs/zeus.h           |  7 -------
 67 files changed, 8 insertions(+), 595 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/ADCIOP.h b/include/configs/ADCIOP.h
index 4632991..5d28168 100644
--- a/include/configs/ADCIOP.h
+++ b/include/configs/ADCIOP.h
@@ -191,15 +191,6 @@
 #define CFG_ETH_DEV_FN	     0x0000
 #define CFG_ETH_IOBASE	     0x0fff0000
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		2048	/* For PLX IOP480			*/
-#define CFG_CACHELINE_SIZE	16	/* For AMCC 401/403 CPUs		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/AP1000.h b/include/configs/AP1000.h
index d25aa74..d490b33 100644
--- a/include/configs/AP1000.h
+++ b/include/configs/AP1000.h
@@ -193,14 +193,6 @@
 #define CFG_ENV_ADDR	    \
     (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)	/* Env	*/
 #endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384
-#define CFG_CACHELINE_SIZE	32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value    */
-#endif
 
 /*
  * Init Memory Controller:
diff --git a/include/configs/AR405.h b/include/configs/AR405.h
index 0f301ec..50f09b0 100644
--- a/include/configs/AR405.h
+++ b/include/configs/AR405.h
@@ -213,16 +213,6 @@
 #define CFG_ENV_ADDR_REDUND     0xFFFA0000
 #define CFG_ENV_SIZE_REDUND	CFG_ENV_SIZE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index 9adbba9..85c6a99 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -258,16 +258,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CANBT.h b/include/configs/CANBT.h
index ae32f6b..7029dbd 100644
--- a/include/configs/CANBT.h
+++ b/include/configs/CANBT.h
@@ -181,15 +181,6 @@
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h
index 21cd9c1..285cd5c 100644
--- a/include/configs/CMS700.h
+++ b/include/configs/CMS700.h
@@ -273,16 +273,6 @@
 #define CFG_EEPROM_WREN         1
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 #define CFG_PLD_BASE            0xf0000000
diff --git a/include/configs/CPCI2DP.h b/include/configs/CPCI2DP.h
index a3717b9..58900c3 100644
--- a/include/configs/CPCI2DP.h
+++ b/include/configs/CPCI2DP.h
@@ -223,16 +223,6 @@
 
 #define CFG_EEPROM_WREN         1
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h
index 1b948f6..bd43e1d 100644
--- a/include/configs/CPCI405.h
+++ b/include/configs/CPCI405.h
@@ -266,15 +266,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index fb71c5f..b248639 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -317,16 +317,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 4994319..1e9597d 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -288,16 +288,6 @@
 #define CFG_NVRAM_SIZE		(32*1024)		/* NVRAM size		*/
 #define CFG_VXWORKS_MAC_PTR     (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h
index 29f9292..a8029ea 100644
--- a/include/configs/CPCI405DT.h
+++ b/include/configs/CPCI405DT.h
@@ -319,16 +319,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CPCI440.h b/include/configs/CPCI440.h
index 318ada1..eb47cd7 100644
--- a/include/configs/CPCI440.h
+++ b/include/configs/CPCI440.h
@@ -262,15 +262,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		32768	/* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 
 /* Configuration Port location */
 #define CONFIG_PORT_ADDR	0xF0000500
diff --git a/include/configs/CPCIISER4.h b/include/configs/CPCIISER4.h
index c7b623a..78b754c 100644
--- a/include/configs/CPCIISER4.h
+++ b/include/configs/CPCIISER4.h
@@ -205,15 +205,6 @@
 #define CFG_ENV_SIZE		0x300	/* 768 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h
index a965c12..2356858 100644
--- a/include/configs/CRAYL1.h
+++ b/include/configs/CRAYL1.h
@@ -192,12 +192,6 @@
 #define CFG_MEMTEST_END		(CFG_SDRAM_SIZE * 1024 * 1024 - CFG_MEM_END_USAGE)
 /* END ENVIRONNEMENT FLASH */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration.  Only used to ..?? clear it, I guess..
- */
-#define CFG_DCACHE_SIZE		16384
-#define CFG_CACHELINE_SIZE	32
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/DASA_SIM.h b/include/configs/DASA_SIM.h
index 627ea14..117a136 100644
--- a/include/configs/DASA_SIM.h
+++ b/include/configs/DASA_SIM.h
@@ -182,15 +182,6 @@
 #define CFG_PCI9054_DEV_FN   0x0800
 #define CFG_PCI9054_IOBASE   0x0eff0000
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		2048	/* For PLX IOP480			*/
-#define CFG_CACHELINE_SIZE	16	/* For AMCC 401/403 CPUs		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/DP405.h b/include/configs/DP405.h
index 2eadbea..912fb2a 100644
--- a/include/configs/DP405.h
+++ b/include/configs/DP405.h
@@ -242,16 +242,6 @@
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 
diff --git a/include/configs/DU405.h b/include/configs/DU405.h
index 5c595f5..c8bf67f 100644
--- a/include/configs/DU405.h
+++ b/include/configs/DU405.h
@@ -232,15 +232,6 @@
 #define CFG_ENV_SIZE		0x400	/* 1024 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/ERIC.h b/include/configs/ERIC.h
index 5d48d2b..dc15b0c 100644
--- a/include/configs/ERIC.h
+++ b/include/configs/ERIC.h
@@ -323,14 +323,6 @@
 #define CFG_ENV_ADDR		\
 	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)	/* Env	*/
 #endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
 
 /*
  * Init Memory Controller:
diff --git a/include/configs/EXBITGEN.h b/include/configs/EXBITGEN.h
index a3f38bb..251227c 100644
--- a/include/configs/EXBITGEN.h
+++ b/include/configs/EXBITGEN.h
@@ -205,10 +205,6 @@
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-/* Cache configuration */
-#define CFG_DCACHE_SIZE		8192
-#define CFG_CACHELINE_SIZE	32
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/G2000.h b/include/configs/G2000.h
index 9c713c6..c12ce48 100644
--- a/include/configs/G2000.h
+++ b/include/configs/G2000.h
@@ -331,16 +331,6 @@
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 
diff --git a/include/configs/HH405.h b/include/configs/HH405.h
index 8967b3f..18e5b3c 100644
--- a/include/configs/HH405.h
+++ b/include/configs/HH405.h
@@ -363,16 +363,6 @@
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's    */
-					/* have only 8kB, 16kB is save here     */
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 
diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index 1ff7108..a389d58 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -257,16 +257,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/JSE.h b/include/configs/JSE.h
index ea3b0b4..5b40ef6 100644
--- a/include/configs/JSE.h
+++ b/include/configs/JSE.h
@@ -279,15 +279,6 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405GPr CPUs	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h
index 3644e43..816e63b 100644
--- a/include/configs/KAREF.h
+++ b/include/configs/KAREF.h
@@ -281,14 +281,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE	      8192	     /* For AMCC 405 CPUs	*/
-#define CFG_CACHELINE_SIZE    32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT   5		     /* log base 2 of the above */
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h
index 8d7ec59..d61b49e 100644
--- a/include/configs/METROBOX.h
+++ b/include/configs/METROBOX.h
@@ -346,14 +346,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE	      8192	     /* For AMCC 405 CPUs	*/
-#define CFG_CACHELINE_SIZE    32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT   5		     /* log base 2 of the above */
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h
index 5b526a0..9ddf82b 100644
--- a/include/configs/MIP405.h
+++ b/include/configs/MIP405.h
@@ -258,15 +258,6 @@
 */
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		0x4000	/* For AMCC 405GPr CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * Logbuffer Configuration
  */
 #undef CONFIG_LOGBUFFER 	/* supported but not enabled */
diff --git a/include/configs/ML2.h b/include/configs/ML2.h
index f488275..66dae21 100644
--- a/include/configs/ML2.h
+++ b/include/configs/ML2.h
@@ -201,14 +201,6 @@
 #define CFG_ENV_ADDR		\
 	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)	/* Env	*/
 #endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
 
 /*
  * Init Memory Controller:
diff --git a/include/configs/OCRTC.h b/include/configs/OCRTC.h
index 5840ea2..94b5bc9 100644
--- a/include/configs/OCRTC.h
+++ b/include/configs/OCRTC.h
@@ -222,15 +222,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/ORSG.h b/include/configs/ORSG.h
index 937df22..4e03088 100644
--- a/include/configs/ORSG.h
+++ b/include/configs/ORSG.h
@@ -220,15 +220,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/PCI405.h b/include/configs/PCI405.h
index d6e7082..e70c0d3 100644
--- a/include/configs/PCI405.h
+++ b/include/configs/PCI405.h
@@ -251,15 +251,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h
index efa0157..b83520d 100644
--- a/include/configs/PIP405.h
+++ b/include/configs/PIP405.h
@@ -231,15 +231,6 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  */
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 652210c..6b16654 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -300,16 +300,6 @@
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 
diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h
index b29f368..adbe8a9 100644
--- a/include/configs/PMC405.h
+++ b/include/configs/PMC405.h
@@ -270,16 +270,6 @@
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 #define FLASH0_BA	0xFF000000	    /* FLASH 0 Base Address		*/
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
index 8a74c4f..c2aa2cc 100644
--- a/include/configs/PPChameleonEVB.h
+++ b/include/configs/PPChameleonEVB.h
@@ -454,16 +454,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h
index 14848ab..3a413f5 100644
--- a/include/configs/VOH405.h
+++ b/include/configs/VOH405.h
@@ -306,16 +306,6 @@
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 
diff --git a/include/configs/VOM405.h b/include/configs/VOM405.h
index 5512f4b..ec6f205 100644
--- a/include/configs/VOM405.h
+++ b/include/configs/VOM405.h
@@ -248,16 +248,6 @@
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 
diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
index fc177fb..7017fff 100644
--- a/include/configs/W7OLMC.h
+++ b/include/configs/W7OLMC.h
@@ -290,15 +290,6 @@
  */
 #define SPD_EEPROM_ADDRESS      0x50	/* XXX conflicting address!!! XXX */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192		/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32		/* ...		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above val. */
-#endif
-
 /*
  * Init Memory Controller:
  */
diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h
index 20d693f..bfb3156 100644
--- a/include/configs/W7OLMG.h
+++ b/include/configs/W7OLMG.h
@@ -293,15 +293,6 @@
  */
 #define SPD_EEPROM_ADDRESS      0x50	/* XXX conflicting address!!! XXX */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192		/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32		/* ...		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above val. */
-#endif
-
 /*
  * Init Memory Controller:
  */
diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h
index 656784a..582d8cf 100644
--- a/include/configs/WUH405.h
+++ b/include/configs/WUH405.h
@@ -254,16 +254,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/XPEDITE1K.h b/include/configs/XPEDITE1K.h
index 611f5a6..38ea576 100644
--- a/include/configs/XPEDITE1K.h
+++ b/include/configs/XPEDITE1K.h
@@ -257,14 +257,6 @@ extern void out32(unsigned int, unsigned long);
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192 /* For AMCC 440GX CPUs */
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index e3f6e2c..dc322dd 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -385,15 +385,6 @@
 #define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384		/* For AMCC 405EZ CPU		*/
-#define CFG_CACHELINE_SIZE	32		/* ...				*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above value*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
 #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index d88c3ad..aff9823 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -355,12 +355,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		32768	/* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 
 /*
  * Internal Definitions
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 14c5638..d577448 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -414,15 +414,6 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h
index 7736a1e..eca195a 100644
--- a/include/configs/bubinga.h
+++ b/include/configs/bubinga.h
@@ -321,14 +321,6 @@
 #define CFG_ENV_ADDR		\
 	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)	/* Env	*/
 #endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405EP CPU			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
 
 /*
  * Init Memory Controller:
diff --git a/include/configs/csb272.h b/include/configs/csb272.h
index c43b497..a24478d 100644
--- a/include/configs/csb272.h
+++ b/include/configs/csb272.h
@@ -290,14 +290,6 @@
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*
- * Cache configuration
- *
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's */
-					/* have only 8kB, 16kB is save here  */
-#define CFG_CACHELINE_SIZE	32
-
-/*
  * Miscellaneous board specific definitions
  *
  */
diff --git a/include/configs/csb472.h b/include/configs/csb472.h
index a7120aa..064650c 100644
--- a/include/configs/csb472.h
+++ b/include/configs/csb472.h
@@ -289,14 +289,6 @@
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*
- * Cache configuration
- *
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's */
-					/* have only 8kB, 16kB is save here  */
-#define CFG_CACHELINE_SIZE	32
-
-/*
  * Miscellaneous board specific definitions
  *
  */
diff --git a/include/configs/ebony.h b/include/configs/ebony.h
index 2c626a0..5faa9eb 100644
--- a/include/configs/ebony.h
+++ b/include/configs/ebony.h
@@ -293,14 +293,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h
index 577f459..b43b228 100644
--- a/include/configs/hcu4.h
+++ b/include/configs/hcu4.h
@@ -321,13 +321,6 @@
 #define CONFIG_PORT_ADDR	0xF0000500
 
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405GPr CPUs	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#define CFG_CACHELINE_SHIFT	5	      /* log base 2 of the above value	*/
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h
index 9085881..1214bc3 100644
--- a/include/configs/hcu5.h
+++ b/include/configs/hcu5.h
@@ -364,13 +364,6 @@
 #define HCU_CPLD_VERSION_REGISTER ( CFG_CPLD + 0x0F00000 )
 #define HCU_HW_VERSION_REGISTER   ( CFG_CPLD + 0x1400000 )
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE		(32<<10)  /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	      /* ...			            */
-#define CFG_CACHELINE_SHIFT	5	      /* log base 2 of the above value	*/
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 5da00fc..2eed941 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -431,14 +431,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/*Initial Memory map for Linux*/
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs		*/
-#define CFG_CACHELINE_SIZE	32	/* ...				*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 9a9f7ba..caf8b52 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -330,15 +330,6 @@
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE		(16 << 10) /* For IBM 405EX			*/
-#define CFG_CACHELINE_SIZE	32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
 #define CFG_NAND_CS		1		/* NAND chip connected to CSx	*/
diff --git a/include/configs/luan.h b/include/configs/luan.h
index a09dd74..cba7295 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -293,15 +293,6 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index 52deab4..3180617 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -487,15 +487,6 @@
 }											\
 }
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE		(32<<10)  /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	      /* ...			            */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	      /* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index 3e3b008..3070779 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -319,15 +319,6 @@
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE		(16 << 10) /* For IBM 405EX			*/
-#define CFG_CACHELINE_SIZE	32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
diff --git a/include/configs/ml300.h b/include/configs/ml300.h
index 0183041..1945918 100644
--- a/include/configs/ml300.h
+++ b/include/configs/ml300.h
@@ -160,12 +160,6 @@
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-
-/*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index bc2fd33..fd4d3af 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -317,14 +317,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		32768	/* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h
index 51f19a1..255e072 100644
--- a/include/configs/p3p440.h
+++ b/include/configs/p3p440.h
@@ -311,14 +311,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10)	/* For AMCC 405 CPUs		*/
-#define CFG_CACHELINE_SIZE	32	/* ...					*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index 7653ba1..d467338 100644
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -438,15 +438,6 @@
 }											\
 }
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/sbc405.h b/include/configs/sbc405.h
index dc906b1..60d401f 100644
--- a/include/configs/sbc405.h
+++ b/include/configs/sbc405.h
@@ -234,16 +234,6 @@
 #define CFG_ENV_SIZE		0x40000	/* Total Size of Environment Sector	*/
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...					*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 #define FLASH0_BA	CFG_FLASH_BASE		/* FLASH 0 Base Address		*/
diff --git a/include/configs/sc3.h b/include/configs/sc3.h
index cb22536..0a03c0e 100644
--- a/include/configs/sc3.h
+++ b/include/configs/sc3.h
@@ -433,24 +433,6 @@ extern unsigned long offsetOfEnvironment;
 #define CONFIG_JFFS2_PART_SIZE		0x01000000
 #define CONFIG_JFFS2_PART_OFFSET	0x00000000
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *
- * CFG_DCACHE_SIZE -> size of data cache:
- * - 405GP 8k
- * - 405GPr 16k
- * How to handle the difference in chache size?
- * CFG_CACHELINE_SIZE -> size of one cache line: 32 bytes
- * (used in cpu/ppc4xx/start.S)
-*/
-#define CFG_DCACHE_SIZE    16384
-
-#define CFG_CACHELINE_SIZE 32
-
-#if defined(CONFIG_CMD_KGDB)
- #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 600f98c..72f01d9 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -43,6 +43,14 @@
 #define CONFIG_SYS_CLK_FREQ    ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
 				33333333 : 33000000)
 
+#if 0
+/*
+ * 44x dcache supported is working now on sequoia, but we don't enable
+ * it yet since it needs further testing
+ */
+#define CONFIG_4xx_DCACHE			/* enable dcache	*/
+#endif
+
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
 #define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
 
@@ -460,15 +468,6 @@
 #define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
 #define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE		(32<<10)  /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	      /* ...			            */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	      /* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/taihu.h b/include/configs/taihu.h
index 6d204a9..c51468b 100644
--- a/include/configs/taihu.h
+++ b/include/configs/taihu.h
@@ -366,13 +366,6 @@ unsigned char spi_read(void);
 }												\
 }
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405EP CPU */
-#define CFG_CACHELINE_SIZE	32
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-
 /*
  * Init Memory Controller:
  *
diff --git a/include/configs/taishan.h b/include/configs/taishan.h
index baa4fbd..ab3b0c1 100644
--- a/include/configs/taishan.h
+++ b/include/configs/taishan.h
@@ -319,15 +319,6 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE		32768	/* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/walnut.h b/include/configs/walnut.h
index 180549e..19b29e7 100644
--- a/include/configs/walnut.h
+++ b/include/configs/walnut.h
@@ -290,16 +290,6 @@
 #endif
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
 
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index 35bce4a..2dde9be 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -361,15 +361,6 @@
 
 #define CFG_BCSR5_PCI66EN	0x80
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 2b4024d..db1d35b 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -324,14 +324,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/*Initial Memory map for Linux*/
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192	/* For AMCC 405 CPUs		*/
-#define CFG_CACHELINE_SIZE	32	/* ...				*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
 
 /*
  * Internal Definitions
diff --git a/include/configs/zeus.h b/include/configs/zeus.h
index 605755a..810a528 100644
--- a/include/configs/zeus.h
+++ b/include/configs/zeus.h
@@ -237,13 +237,6 @@
 #endif
 
 /*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405EP CPU			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-
-/*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory (OCM) for temperary stack until sdram is tested */
-- 
cgit v1.1


From 3d6cb3b24add6415f86a0f013ea40f5639b90047 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Sat, 3 Nov 2007 12:08:28 +0100
Subject: ppc4xx: Add AMCC Kilauea/Haleakala NAND booting support

This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 88 ++++++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 79 insertions(+), 9 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index caf8b52..07f7eff 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -50,7 +50,7 @@
 #define CFG_FPGA_BASE		0xF0000000
 #define CFG_PERIPHERAL_BASE	0xEF600000      /* internal peripherals*/
 #define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc()	*/
 #define CFG_MONITOR_BASE	(TEXT_BASE)
 
 /*-----------------------------------------------------------------------
@@ -117,6 +117,71 @@
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 #endif /* CFG_ENV_IS_IN_FLASH */
 
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller.	sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
+#define CFG_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
+#define CFG_NAND_BOOT_SPL_DST	0x00800000	/* Copy SPL here		*/
+#define CFG_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr	*/
+#define CFG_NAND_U_BOOT_START	CFG_NAND_U_BOOT_DST /* Start NUB from this addr	*/
+#define CFG_NAND_BOOT_SPL_DELTA	(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image	*/
+#define CFG_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image	*/
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE	512		/* NAND chip page size		*/
+#define CFG_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size		*/
+#define CFG_NAND_PAGE_COUNT	32		/* NAND chip page count		*/
+#define CFG_NAND_BAD_BLOCK_POS	5		/* Location of bad block marker	*/
+#define CFG_NAND_4_ADDR_CYCLE	1		/* Fourth addr used (>32MB)	*/
+
+#define CFG_NAND_ECCSIZE	256
+#define CFG_NAND_ECCBYTES	3
+#define CFG_NAND_ECCSTEPS	(CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE	16
+#define CFG_NAND_ECCTOTAL	(CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE		CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET		(CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS		1
+#define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
+
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
@@ -332,6 +397,18 @@
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+/* booting from NAND, so NAND chips select has to be on CS 0 */
+#define CFG_NAND_CS		0		/* NAND chip connected to CSx	*/
+
+/* Memory Bank 1 (NOR-FLASH) initialization					*/
+#define CFG_EBC_PB1AP		0x05806500
+#define CFG_EBC_PB1CR           0xFC0DA000  /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 0 (NAND-FLASH) initialization					*/
+#define CFG_EBC_PB0AP		0x018003c0
+#define CFG_EBC_PB0CR		(CFG_NAND_ADDR | 0x1e000)
+#else
 #define CFG_NAND_CS		1		/* NAND chip connected to CSx	*/
 
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
@@ -341,6 +418,7 @@
 /* Memory Bank 1 (NAND-FLASH) initialization					*/
 #define CFG_EBC_PB1AP		0x018003c0
 #define CFG_EBC_PB1CR		(CFG_NAND_ADDR | 0x1e000)
+#endif
 
 /* Memory Bank 2 (FPGA) initialization						*/
 #define CFG_EBC_PB2AP           0x9400C800
@@ -349,14 +427,6 @@
 #define CFG_EBC_CFG		0x7FC00000 /*  EBC0_CFG */
 
 /*-----------------------------------------------------------------------
- * NAND FLASH
- *----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE	1
-#define NAND_MAX_CHIPS		1
-#define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
-
-/*-----------------------------------------------------------------------
  * GPIO Setup
  *----------------------------------------------------------------------*/
 /*-----------------------------------------------------------------------
-- 
cgit v1.1


From 9f23ca334a6f5f021ef9e9d0fad9da80d63b2d56 Mon Sep 17 00:00:00 2001
From: Jason Jin <Jason.jin@freescale.com>
Date: Mon, 29 Oct 2007 19:26:21 +0800
Subject: Unify pixis_reset altbank across board families

Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8544DS.h   | 1 +
 include/configs/MPC8641HPCN.h | 1 +
 2 files changed, 2 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index f580cca..13e2a2c 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -198,6 +198,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
 
 
 /* define to use L1 as initial stack */
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index aa6dbc4..6f87240 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -201,6 +201,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
 
 #define CFG_MAX_FLASH_BANKS	2		/* number of banks */
 #define CFG_MAX_FLASH_SECT	128		/* sectors per device */
-- 
cgit v1.1


From f3bceaab230b4748d0afc4109b6837308f018b40 Mon Sep 17 00:00:00 2001
From: Jason Jin <Jason.jin@freescale.com>
Date: Fri, 26 Oct 2007 18:31:59 +0800
Subject: Fix the BAT definition of PCI IO on 8610 board

The address in the BAT register is aligned with the BAT size.
The original definition actually did not define BAT for PCIE2 IO.
This patch fix this.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
---
 include/configs/MPC8610HPCD.h | 16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index be3434a..8bbe447 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -361,28 +361,26 @@
 #define CFG_IBAT1U	CFG_DBAT1U
 
 /*
- * BAT2		32M	Cache-inhibited, guarded
+ * BAT2		16M	Cache-inhibited, guarded
  * 0xe100_0000	1M	PCI-1 I/O
- * 0xe200_0000	1M	PCI-Express 2 I/O
- *
  */
 
 #define CFG_DBAT2L	(CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U	(CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_DBAT2U	(CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP)
 #define CFG_IBAT2L	(CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CFG_IBAT2U	CFG_DBAT2U
 
 /*
- * BAT3		1M	Cache-inhibited, guarded
+ * BAT3		32M	Cache-inhibited, guarded
+ * 0xe200_0000	1M	PCI-Express 2 I/O
  * 0xe300_0000	1M	PCI-Express 1 I/O
- *
  */
 
-#define CFG_DBAT3L	(CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CFG_DBAT3L	(CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT3U	(CFG_PCIE1_IO_PHYS | BATU_BL_1M | BATU_VS | BATU_VP)
-#define CFG_IBAT3L	(CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_DBAT3U	(CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L	(CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CFG_IBAT3U	CFG_DBAT3U
 
 /*
-- 
cgit v1.1


From 761421ccca80a9fb37b19c37aa61d46ef75e0647 Mon Sep 17 00:00:00 2001
From: Jason Jin <Jason.jin@freescale.com>
Date: Mon, 29 Oct 2007 19:26:21 +0800
Subject: 8610: Actually enable pixis_reset CONFIGs

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
---
 include/configs/MPC8610HPCD.h | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 8bbe447..8b6b117 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -151,6 +151,7 @@
 #define CFG_OR3_PRELIM		0xfff06ff7 /* 1MB PIXIS area*/
 
 
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xe8000000	/* PIXIS registers */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
@@ -166,6 +167,7 @@
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK	0x0C    /* Reset altbank mask*/
 
 #define CFG_MAX_FLASH_BANKS	2		/* number of banks */
 #define CFG_MAX_FLASH_SECT	1024		/* sectors per device */
-- 
cgit v1.1


From 1815338fbd1c0f94f8276d2891b99caa5a05f622 Mon Sep 17 00:00:00 2001
From: York Sun <yorksun@freescale.com>
Date: Mon, 29 Oct 2007 13:57:53 -0500
Subject: 8610: Make some extra debug environment variables conditional.

One may #define ENV_DEBUG to get them back again.

Signed-off-by: York Sun <yorksun@freescale.com>
---
 include/configs/MPC8610HPCD.h | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 8b6b117..9fa42f3 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -587,7 +587,7 @@
  "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
 	"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
 
-
+#ifdef ENV_DEBUG
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
  "netdev=eth0\0"						\
  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
@@ -632,6 +632,17 @@
  PCI_ENV \
  PCIE_ENV \
  DMA_ENV
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS                               \
+ "netdev=eth0\0"                                                \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                         \
+ "consoledev=ttyS0\0"                                           \
+ "ramdiskaddr=2000000\0"                                        \
+ "ramdiskfile=8610hpcd/ramdisk.uboot\0"                         \
+ "dtbaddr=c00000\0"                                             \
+ "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0"                          \
+ "bdev=sda3\0"
+#endif
 
 #define CONFIG_NFSBOOTCOMMAND					\
  "setenv bootargs root=/dev/nfs rw "				\
-- 
cgit v1.1


From a877880c6949e948bd63cd6ea4e216573d2f53dd Mon Sep 17 00:00:00 2001
From: York Sun <yorksun@freescale.com>
Date: Mon, 29 Oct 2007 13:58:39 -0500
Subject: 8610: Add 8610 DIU display driver

1280x1024 and 1024x768 @ 32 bpp are supported now.
DVI, Single-link LVDS, Double-link LVDS are all supported.

Environmental variable "monitor" is used to specify monitor port.

A new command "diufb" is introduced to reinitialize monitor
and display a BMP file in the memory. So far, 1-bit, 4-bit,
8-bit and 24-bit BMP formats are supported.

    diufb init
        - initialize the diu driver
    Enable the port specified in the environmental variable "monitor"

    diufb addr
        - display bmp file in memory.
    The bmp image should be no bigger than the resolution, 1280x1024
    for DVI and double-link LVDS, 1024x768 for single-link LVDS.

Note, this driver allocate memory but doesn't free it after use
It is written on purpose -- to avoid a failure of reallocation
due to memory fragement.

ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon loeliger <jdl@freescale.com>
---
 include/configs/MPC8610HPCD.h | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 9fa42f3..00c94ef 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -21,6 +21,7 @@
 #define CONFIG_NUM_CPUS		1	/* Number of CPUs in the system */
 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
 
+#define CONFIG_FSL_DIU_FB	1	/* FSL DIU */
 #ifdef RUN_DIAG
 #define CFG_DIAG_ADDR		0xff800000
 #endif
@@ -38,7 +39,7 @@
 #define CONFIG_SPD_EEPROM		/* Use SPD for DDR */
 #undef CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#undef  CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 #define CONFIG_NUM_DDR_CONTROLLERS	1
@@ -51,13 +52,14 @@
  */
 #define CFG_L2
 #define L2_INIT		0
-#define L2_ENABLE	(L2CR_L2E)
+#define L2_ENABLE	(L2CR_L2E |0x00100000 )
 
 #ifndef CONFIG_SYS_CLK_FREQ
 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)
 #endif
 
 #define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+#define CONFIG_MISC_INIT_R		1
 
 #undef	CFG_DRAM_TEST			/* memory test, takes time */
 #define CFG_MEMTEST_START	0x00200000	/* memtest region */
@@ -159,6 +161,7 @@
 #define PIXIS_RST		0x4	/* PIXIS Reset Control register */
 #define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch */
 #define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
+#define PIXIS_BRDCFG0		0x8	/* PIXIS Board Configuration Register0*/
 #define PIXIS_VCTL		0x10	/* VELA Control Register */
 #define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
 #define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
@@ -208,7 +211,7 @@
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 #define CFG_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
+#define CFG_MALLOC_LEN		(6 * 1024 * 1024)	/* Reserved for malloc */
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX	1
@@ -474,6 +477,9 @@
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
+/*DIU Configuration*/
+#define DIU_CONNECT_TO_DVI		/* DIU controller connects to DVI encoder*/
+
 /*
  * Miscellaneous configurable options
  */
@@ -621,7 +627,8 @@
  "diuregs=md e002c000 1d\0" \
  "dium=mw e002c01c\0" \
  "diuerr=md e002c014 1\0" \
- "othbootargs=debug\0" \
+ "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 debug\0" \
+ "monitor=0-DVI\0" \
  "pmregs=md e00e1000 2b\0" \
  "lawregs=md e0000c08 4b\0" \
  "lbcregs=md e0005000 36\0" \
@@ -641,7 +648,9 @@
  "ramdiskfile=8610hpcd/ramdisk.uboot\0"                         \
  "dtbaddr=c00000\0"                                             \
  "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0"                          \
- "bdev=sda3\0"
+ "bdev=sda3\0"							\
+ "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\
+ "monitor=0-DVI\0"
 #endif
 
 #define CONFIG_NFSBOOTCOMMAND					\
-- 
cgit v1.1


From 070ba56115b4da63b46e974287fa4550d4023386 Mon Sep 17 00:00:00 2001
From: York Sun <yorksun@freescale.com>
Date: Wed, 31 Oct 2007 14:59:04 -0500
Subject: 8610: Add console frame buffer support to FSL 8610 DIU driver.

Add cfb console support to FSL 8610 DIU driver.
Inspect board version from PIXIS to obtain correct pixel format.

Use #define CONFIG_VIDEO in config file to enable fb console.

To switch monitor, set monitor variable to
0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS
followed by "diufb init".

Preserve logo bitmap at the top of the fb console.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8610HPCD.h | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 00c94ef..f5d9c09 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -22,6 +22,15 @@
 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
 
 #define CONFIG_FSL_DIU_FB	1	/* FSL DIU */
+
+/* video */
+#undef CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#endif
+
 #ifdef RUN_DIAG
 #define CFG_DIAG_ADDR		0xff800000
 #endif
@@ -314,15 +323,17 @@
 #define CONFIG_EEPRO100
 #define CONFIG_TULIP
 
-#if 0 /* TODO */
 /************************************************************
  * USB support
  ************************************************************/
-#define CONFIG_USB_OHCI		1
+#define CONFIG_PCI_OHCI		1
+#define CONFIG_USB_OHCI_NEW		1
 #define CONFIG_USB_KEYBOARD	1
 #define CFG_DEVICE_DEREGISTER
-#define CFG_USB_INTERRUPT_POLL	1
-#endif
+#define CFG_USB_EVENT_POLL	1
+#define CFG_USB_OHCI_SLOT_NAME 	"ohci_pci"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#define CFG_OHCI_SWAP_REG_ACCESS	1
 
 #if !defined(CONFIG_PCI_PNP)
 #define PCI_ENET0_IOADDR	0xe0000000
@@ -472,6 +483,7 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SCSI
 #define CONFIG_CMD_EXT2
+#define CONFIG_CMD_USB
 #endif
 
 
-- 
cgit v1.1


From b53313dbfc74525d85f1e7e0102f902d5c863beb Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Fri, 9 Nov 2007 12:19:58 +0100
Subject: ppc4xx: Remove In:/Out:/Err: boot output for AMCC Kilauea

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 1 +
 1 file changed, 1 insertion(+)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 07f7eff..ddd064a 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -358,6 +358,7 @@
 #define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 /*-----------------------------------------------------------------------
  * PCI stuff
-- 
cgit v1.1


From 2d14684341109a69616e4d6016cd61402d55086f Mon Sep 17 00:00:00 2001
From: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Fri, 9 Nov 2007 15:37:53 +0100
Subject: ppc4xx: Use generic usb-ohci driver for sequoia board

This patch makes the sequoia board use the generic usb-ohci driver
instead of cpu/ppc4xx/usb_ohci.c.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/sequoia.h | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 72f01d9..2af675a 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -301,8 +301,15 @@
 
 /* USB */
 #ifdef CONFIG_440EPX
-#define CONFIG_USB_OHCI
+#define CONFIG_USB_OHCI_NEW
 #define CONFIG_USB_STORAGE
+#define CFG_OHCI_BE_CONTROLLER
+
+#undef CFG_USB_OHCI_BOARD_INIT
+#define CFG_USB_OHCI_CPU_INIT	1
+#define CFG_USB_OHCI_REGS_BASE	CFG_USB_HOST
+#define CFG_USB_OHCI_SLOT_NAME	"ppc440"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
 
 /* Comment this out to enable USB 1.1 device */
 #define USB_2_0_DEVICE
-- 
cgit v1.1


From 1d8a49eca1c7bdc8db1c47a92f9014a29ead03ae Mon Sep 17 00:00:00 2001
From: Roy Zang <tie-fei.zang@freescale.com>
Date: Thu, 13 Sep 2007 18:52:28 +0800
Subject: Enable ULi1575 Ethernet support in 8610HPCD config

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8610HPCD.h | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index f5d9c09..ef1310f 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -312,16 +312,16 @@
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 
 #define CONFIG_NET_MULTI
+#define CONFIG_CMD_NET
 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
 
-#if 0 /* TODO */
-/* enable onboard uli network support */
-#endif
-
 #define CONFIG_RTL8139
 #define CONFIG_SK98
 #define CONFIG_EEPRO100
 #define CONFIG_TULIP
+#ifdef CONFIG_TULIP
+#define CONFIG_ETHADDR   00:E0:0C:00:00:01
+#endif
 
 /************************************************************
  * USB support
-- 
cgit v1.1


From 8ada0ebf38e4073beea0309188b25d82a112a2ae Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Thu, 15 Nov 2007 14:20:08 +0100
Subject: ppc4xx: AMCC Taihu board config file cleanup

This patch makes the AMCC Taihu a little more compatible to the other
AMCC eval boards.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/taihu.h | 44 +++++---------------------------------------
 1 file changed, 5 insertions(+), 39 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/taihu.h b/include/configs/taihu.h
index c51468b..d012c60 100644
--- a/include/configs/taihu.h
+++ b/include/configs/taihu.h
@@ -80,6 +80,7 @@
 	"bootfile=/tftpboot/taihu/uImage\0"				\
 	"rootpath=/opt/eldk/ppc_4xx\0"					\
 	"netdev=eth0\0"							\
+	"hostname=taihu\0"						\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
@@ -210,10 +211,12 @@
 
 #define CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
 
-#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 /*-----------------------------------------------------------------------
  * I2C stuff
@@ -328,7 +331,7 @@ unsigned char spi_read(void);
 /*-----------------------------------------------------------------------
  * PPC405 GPIO Configuration
  */
-#define CFG_440_GPIO_TABLE { /*				GPIO	Alternate1		*/	\
+#define CFG_4xx_GPIO_TABLE { /*				GPIO	Alternate1		*/	\
 {												\
 /* GPIO Core 0 */										\
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO0	PerBLast    SPI CS	*/	\
@@ -415,43 +418,6 @@ unsigned char spi_read(void);
 #define CFG_EBC_PB4AP           0x158FF600
 #define CFG_EBC_PB4CR           0x5021A000
 
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0]     - External Bus Controller BLAST output
- * GPIO0[1-9]   - Instruction trace outputs
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
- */
-#define CFG_GPIO0_OSRH	0x15555550	/* output select high/low */
-#define CFG_GPIO0_OSRL	0x00000110
-#define CFG_GPIO0_ISR1H	0x00000001	/* input select high/low */
-#define CFG_GPIO0_ISR1L	0x15545440
-#define CFG_GPIO0_TSRH	0x00000000	/* three-state select high/low */
-#define CFG_GPIO0_TSRL	0x00000000
-#define CFG_GPIO0_TCR	0xFFFE8117	/* three-state control */
-#define CFG_GPIO0_ODR	0x00000000	/* open drain */
-
-#define GPIO0		0		/* GPIO controller 0 */
-
-/* the GPIO macros in include/ppc405.h for High/Low registers are backwards */
-
-#define GPIOx_OSL	(GPIO0_OSRH-GPIO_BASE)
-#define GPIOx_TSL	(GPIO0_TSRH-GPIO_BASE)
-#define GPIOx_IS1L	(GPIO0_ISR1H-GPIO_BASE)
-#define GPIOx_IS2L	(GPIO0_ISR1H-GPIO_BASE)
-#define GPIOx_IS3L	(GPIO0_ISR1H-GPIO_BASE)
-
-#define GPIO_OS(x)	(x+GPIOx_OSL)	/* GPIO output select */
-#define GPIO_TS(x)	(x+GPIOx_TSL)	/* GPIO three-state select */
-#define GPIO_IS1(x)	(x+GPIOx_IS1L)	/* GPIO input select */
-#define GPIO_IS2(x)	(x+GPIOx_IS1L)
-#define GPIO_IS3(x)	(x+GPIOx_IS1L)
-
 #define CPLD_REG0_ADDR	0x50100000
 #define CPLD_REG1_ADDR	0x50100001
 /*
-- 
cgit v1.1


From aee747f19b460a0e9da20ff21e90fdaac1cec359 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Thu, 15 Nov 2007 14:23:55 +0100
Subject: ppc4xx: Enable 440 GPIO init table CFG_440_GPIO_TABLE for 405
 platforms

- Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE
- Cleanup of the 4xx GPIO functions
- Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/lwmon5.h   | 2 +-
 include/configs/pcs440ep.h | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index 3180617..9cb483d 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -414,7 +414,7 @@
 /*-----------------------------------------------------------------------
  * PPC440 GPIO Configuration
  */
-#define CFG_440_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
+#define CFG_4xx_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
 {											\
 /* GPIO Core 0 */									\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0	EBC_ADDR(7)	DMA_REQ(2)	*/	\
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index d467338..d66f4bd 100644
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -365,7 +365,7 @@
 /*-----------------------------------------------------------------------
  * PPC440 GPIO Configuration
  */
-#define CFG_440_GPIO_TABLE { /*	  Out		       GPIO	Alternate1	Alternate2   Alternate3 */ \
+#define CFG_4xx_GPIO_TABLE { /*	  Out		       GPIO	Alternate1	Alternate2   Alternate3 */ \
 {											\
 /* GPIO Core 0 */									\
 {GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG},  /* GPIO0	EBC_ADDR(7)	DMA_REQ(2)	*/ \
-- 
cgit v1.1


From ecdcbd4f8c1f8cefd785752f4e7536aae2a4ecf9 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Fri, 16 Nov 2007 14:00:59 +0100
Subject: ppc4xx: Update AMCC Makalu for board rev 1.1

This patch adds changes needed for Makalu rev 1.1:

- Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
- Enable 2nd ethernet port EMAC1
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
- Reset PCIe ports via GPIO upon bootup

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/makalu.h | 78 ++++++++++++++++++++++++++++++------------------
 1 file changed, 49 insertions(+), 29 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index 3070779..aa421c1 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -44,11 +44,11 @@
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0xFE000000
+#define CFG_FLASH_BASE		0xFC000000
 #define CFG_FPGA_BASE		0xF0000000
 #define CFG_PERIPHERAL_BASE	0xEF600000      /* internal peripherals*/
 #define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc()	*/
 #define CFG_MONITOR_BASE	(TEXT_BASE)
 
 /*-----------------------------------------------------------------------
@@ -113,7 +113,7 @@
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM        128
+#define CFG_MBYTES_SDRAM	256
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -150,7 +150,7 @@
 
 #define CONFIG_NET_MULTI	1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
-#define CONFIG_PHY1_ADDR	2
+#define CONFIG_PHY1_ADDR	0
 
 #define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
 
@@ -187,8 +187,8 @@
 	"bootfile=makalu/uImage\0"					\
 	"fdt_file=makalu/makalu.dtb\0"					\
 	"fdt_addr=400000\0"						\
-	"kernel_addr=fe000000\0"					\
-	"ramdisk_addr=fe200000\0"					\
+	"kernel_addr=fc000000\0"					\
+	"ramdisk_addr=fc200000\0"					\
 	"initrd_high=30000000\0"					\
 	"load=tftp 200000 makalu/u-boot.bin\0"				\
 	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
@@ -282,6 +282,7 @@
 #define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -323,7 +324,7 @@
  *----------------------------------------------------------------------*/
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
 #define CFG_EBC_PB0AP		0x04011000
-#define CFG_EBC_PB0CR           0xFE0BA000  /* BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB0CR		(CFG_FLASH_BASE | 0xda000)
 
 /* Memory Bank 2 (CPLD) initialization						*/
 #define CFG_EBC_PB2AP           0x9400C800
@@ -334,28 +335,47 @@
 /*-----------------------------------------------------------------------
  * GPIO Setup
  *----------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EX specific)
- *
- * GPIO0[0-3]      - EBC data 0-3	inputs/outputs
- * GPIO0[4-7]      - USB data 4-7	inputs/outputs
- * GPIO0[8-11]     - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
- * GPIO0[12-15]    - USB data 0-3	inputs/outputs
- * GPIO0[16-21]    - UART0 control signal inputs/outputs
- *
- * GPIO0[22-25,27] - EBC control signal inputs/outputs
- * GPIO0[26]	   - Instruction trace outputs
- * GPIO0[28]	   - Float, N/C
- * GPIO0[29-31]    - DMA control signal inputs/outputs
- */
-#define CFG_GPIO0_OSRL		0x00AA54AA
-#define CFG_GPIO0_OSRH		0x55500000
-#define CFG_GPIO0_TSRL		0x00AA54AA
-#define CFG_GPIO0_TSRH		0x55500000
-#define CFG_GPIO0_ISR1L		0x00005400
-#define CFG_GPIO0_ISR1H		0x55500000
-#define CFG_GPIO0_ISR2L		0x00550055
-#define CFG_GPIO0_ISR2H		0x00000000
+#define CFG_4xx_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
+{											\
+/* GPIO Core 0 */									\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO0	EBC_DATA_PAR(0)			*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO1	EBC_DATA_PAR(1)			*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO2	EBC_DATA_PAR(2)			*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO3	EBC_DATA_PAR(3)			*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4	EBC_DATA(20)	USB2_DATA(4)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	EBC_CS(1)	NFCE(1)		IRQ(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	EBC_CS(2)	NFCE(2)		IRQ(8) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3)	NFCE(3)		IRQ(9) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS			*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO20 UART0_DTR	UART1_TX	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO21 UART0_RI	UART1_RX	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ	DMA_ACK2	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK	DMA_REQ2	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ	DMA_EOT2	IRQ(4) */ \
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK	DMA_ACK3	IRQ(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO28				*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO29 IRQ(2)		DMA_EOT1	*/	\
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 IRQ(1)		DMA_REQ1	*/	\
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO31 IRQ(0)		DMA_ACK1	*/	\
+}												\
+}
+
+#define CFG_GPIO_PCIE_RST	23
+#define CFG_GPIO_PCIE_CLKREQ	27
+#define CFG_GPIO_PCIE_WAKE	28
 
 /*
  * Internal Definitions
-- 
cgit v1.1


From db74b3c1c9481a6bffbf8cd445e5bcbf6908e836 Mon Sep 17 00:00:00 2001
From: Jason Jin <Jason.jin@freescale.com>
Date: Mon, 29 Oct 2007 19:26:21 +0800
Subject: Unify pixis_reset altbank across board families

Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8544DS.h   | 1 +
 include/configs/MPC8641HPCN.h | 1 +
 2 files changed, 2 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index f580cca..13e2a2c 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -198,6 +198,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
 
 
 /* define to use L1 as initial stack */
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index aa6dbc4..6f87240 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -201,6 +201,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
 
 #define CFG_MAX_FLASH_BANKS	2		/* number of banks */
 #define CFG_MAX_FLASH_SECT	128		/* sectors per device */
-- 
cgit v1.1


From fd329e6f05bbdfe6bd71b0e09f0c76d3b0a025a5 Mon Sep 17 00:00:00 2001
From: Luotao Fu <l.fu@pengutronix.de>
Date: Wed, 14 Nov 2007 18:58:33 +0100
Subject: Fix the i2c frequency and default address in rsdproto board

rsdproto board support has wrong I2C frequency and wrong return value
handling.

Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
---
 include/configs/rsdproto.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h
index 814082c..40a05fa 100644
--- a/include/configs/rsdproto.h
+++ b/include/configs/rsdproto.h
@@ -92,8 +92,8 @@
 
 /* enable I2C */
 #define CONFIG_HARD_I2C        	1	/* I2C with hardware support */
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_SPEED		50000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x30
 
 
 /* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-- 
cgit v1.1


From 9ea61b57968554eaf0f474ec7e088b17d367f474 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Sat, 17 Nov 2007 14:52:29 +0100
Subject: ppc4xx: Update AMCC Kilauea config file

- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 60 +++++++++++++++++++++++++++++------------------
 1 file changed, 37 insertions(+), 23 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index ddd064a..b4144b3 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -430,29 +430,43 @@
 /*-----------------------------------------------------------------------
  * GPIO Setup
  *----------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EX specific)
- *
- * GPIO0[0-3]      - EBC data 0-3	inputs/outputs
- * GPIO0[4-7]      - USB data 4-7	inputs/outputs
- * GPIO0[8-11]     - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
- * GPIO0[12-15]    - USB data 0-3	inputs/outputs
- * GPIO0[16-21]    - UART0 control signal inputs/outputs
- *
- * GPIO0[22-25,27] - EBC control signal inputs/outputs
- * GPIO0[26]	   - Instruction trace outputs
- * GPIO0[28]	   - Float, N/C
- * GPIO0[29-31]    - DMA control signal inputs/outputs
- */
-#define CFG_GPIO0_OSRL		0x00AA54AA
-#define CFG_GPIO0_OSRH		0x21800000
-#define CFG_GPIO0_TSRL		0x00AA55AA
-#define CFG_GPIO0_TSRH		0xA5A00000
-
-#define CFG_GPIO0_ISR1L		0x00000100
-#define CFG_GPIO0_ISR1H		0x04000000
-#define CFG_GPIO0_ISR2L		0x00550055
-#define CFG_GPIO0_ISR2H		0x40100000
+#define CFG_4xx_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
+{											\
+/* GPIO Core 0 */									\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO0	EBC_DATA_PAR(0)			*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO1	EBC_DATA_PAR(1)			*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO2	EBC_DATA_PAR(2)			*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO3	EBC_DATA_PAR(3)			*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO4	EBC_DATA(20)	USB2_DATA(4)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	EBC_CS(1)	NFCE(1)		IRQ(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	EBC_CS(2)	NFCE(2)		IRQ(8) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3)	NFCE(3)		IRQ(9) */ \
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/ \
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS			*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR	UART1_TX	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 UART0_RI	UART1_RX	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ	DMA_ACK2	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK	DMA_REQ2	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ	DMA_EOT2	IRQ(4) */ \
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK	DMA_ACK3	IRQ(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO28				*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO29 IRQ(2)		DMA_EOT1	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 IRQ(1)		DMA_REQ1	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO31 IRQ(0)		DMA_ACK1	*/	\
+}												\
+}
 
 /*
  * Internal Definitions
-- 
cgit v1.1


From f30ad49b16bf998b03c1a5228b6c86369d61c258 Mon Sep 17 00:00:00 2001
From: Haiying Wang <Haiying.Wang@freescale.com>
Date: Mon, 19 Nov 2007 10:02:13 -0500
Subject: Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDS

CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
---
 include/configs/MPC8568MDS.h | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 548e158..b9366cc 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -334,11 +334,6 @@ extern unsigned long get_clock_freq(void);
 
 #define CFG_SRIO_MEM_BASE	0xc0000000
 
-#if defined(CONFIG_PCI)
-
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
-
 #ifdef CONFIG_QE
 /*
  * QE UEC ethernet configuration
@@ -377,6 +372,11 @@ extern unsigned long get_clock_freq(void);
 #endif
 #endif /* CONFIG_QE */
 
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
-- 
cgit v1.1


From 68b88999da87ab88e71e1306192905be3450198e Mon Sep 17 00:00:00 2001
From: Jon Loeliger <jdl@freescale.com>
Date: Tue, 20 Nov 2007 15:02:26 -0600
Subject: 8610HPCD: Enable the 8610 Display Interface Unit

Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8610HPCD.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index ef1310f..55df5aa 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -24,7 +24,7 @@
 #define CONFIG_FSL_DIU_FB	1	/* FSL DIU */
 
 /* video */
-#undef CONFIG_VIDEO
+#define CONFIG_VIDEO
 
 #if defined(CONFIG_VIDEO)
 #define CONFIG_CFB_CONSOLE
-- 
cgit v1.1


From 4a43719a7738712811d822ca8125427b27a55cdc Mon Sep 17 00:00:00 2001
From: Grant Likely <grant.likely@secretlab.ca>
Date: Mon, 24 Sep 2007 09:05:31 -0600
Subject: [BUILD] conditionally compile common/cmd_*.c in common/Makefile

Modify common/Makefile to conditionally compile the cmd_*.c files based
on the board config.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 include/configs/sbc2410x.h | 1 -
 include/configs/smdk2410.h | 1 -
 2 files changed, 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/sbc2410x.h b/include/configs/sbc2410x.h
index b4a063a..9b05bd6 100644
--- a/include/configs/sbc2410x.h
+++ b/include/configs/sbc2410x.h
@@ -103,7 +103,6 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 
 
 #define CONFIG_BOOTDELAY	3
diff --git a/include/configs/smdk2410.h b/include/configs/smdk2410.h
index ca404ff..18a036c 100644
--- a/include/configs/smdk2410.h
+++ b/include/configs/smdk2410.h
@@ -88,7 +88,6 @@
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_CACHE
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_ELF
 
-- 
cgit v1.1


From ca1ce226287270bb01e25b8e3674c701f12edf19 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Mon, 26 Nov 2007 15:01:45 +0100
Subject: ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interrupt

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index b4144b3..2bb5f24 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -462,7 +462,7 @@
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO28				*/	\
-{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO29 IRQ(2)		DMA_EOT1	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2)		DMA_EOT1	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 IRQ(1)		DMA_REQ1	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO31 IRQ(0)		DMA_ACK1	*/	\
 }												\
-- 
cgit v1.1


From 63362cfc6baa97ae0e37ba2c6ece530fcac9f79e Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Mon, 26 Nov 2007 15:06:14 +0100
Subject: ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usage

As suggested by Senao, use a different EBC_PB0AP setup for 400MHz
operation.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/makalu.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index aa421c1..18e6daf 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -323,7 +323,7 @@
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
-#define CFG_EBC_PB0AP		0x04011000
+#define CFG_EBC_PB0AP		0x08033700
 #define CFG_EBC_PB0CR		(CFG_FLASH_BASE | 0xda000)
 
 /* Memory Bank 2 (CPLD) initialization						*/
-- 
cgit v1.1


From 8be760903645af09871be50ad0a6f9ebb62b311d Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Tue, 27 Nov 2007 11:57:35 +0100
Subject: ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexing

After an error in the AMCC 405EX users manual now correctly configure
IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ
usage.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 14 +++++++-------
 include/configs/makalu.h  | 12 ++++++------
 2 files changed, 13 insertions(+), 13 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 2bb5f24..98d745c 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -441,16 +441,16 @@
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	EBC_CS(1)	NFCE(1)		IRQ(7) */ \
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	EBC_CS(2)	NFCE(2)		IRQ(8) */ \
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3)	NFCE(3)		IRQ(9) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	CS(1)/NFCE(1)	IRQ(7)		*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	CS(2)/NFCE(2)	IRQ(8)		*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3)	IRQ(9)		*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
-{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/ \
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS			*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR	UART1_TX	*/	\
@@ -462,9 +462,9 @@
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO28				*/	\
-{GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2)		DMA_EOT1	*/	\
-{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 IRQ(1)		DMA_REQ1	*/	\
-{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO31 IRQ(0)		DMA_ACK1	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO29 DMA_EOT1	IRQ(2)		*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 DMA_REQ1	IRQ(1)		*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO31 DMA_ACK1	IRQ(0)		*/	\
 }												\
 }
 
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index 18e6daf..e04efb7 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -346,9 +346,9 @@
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	EBC_CS(1)	NFCE(1)		IRQ(7) */ \
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	EBC_CS(2)	NFCE(2)		IRQ(8) */ \
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3)	NFCE(3)		IRQ(9) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	CS(1)/NFCE(1)	IRQ(7)		*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	CS(2)/NFCE(2)	IRQ(8)		*/	\
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3)	IRQ(9)		*/	\
 {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
@@ -367,9 +367,9 @@
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO28				*/	\
-{GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO29 IRQ(2)		DMA_EOT1	*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 IRQ(1)		DMA_REQ1	*/	\
-{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO31 IRQ(0)		DMA_ACK1	*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO29 DMA_EOT1	IRQ(2)		*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 DMA_REQ1	IRQ(1)		*/	\
+{GPIO0_BASE, GPIO_IN,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1	IRQ(0)		*/	\
 }												\
 }
 
-- 
cgit v1.1


From a90921f71d225bf9e0f0fc7b8beadeb8001bf78a Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Tue, 4 Dec 2007 16:29:48 +0100
Subject: ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 support

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/yosemite.h | 9 +++++++++
 1 file changed, 9 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index 2dde9be..a8eeff9 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -160,6 +160,14 @@
 #define CFG_ENV_OFFSET		0x0
 #endif /* CFG_ENV_IS_IN_EEPROM */
 
+/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
+#define CONFIG_DTT_LM75		1		/* ON Semi's LM75	*/
+#define CONFIG_DTT_AD7414	1		/* use AD7414		*/
+#define CONFIG_DTT_SENSORS	{0}		/* Sensor addresses	*/
+#define CFG_DTT_MAX_TEMP	70
+#define CFG_DTT_LOW_TEMP	-30
+#define CFG_DTT_HYSTERESIS	3
+
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
 	"echo"
@@ -273,6 +281,7 @@
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
+#define CONFIG_CMD_DTT
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
-- 
cgit v1.1


From cf5933ba1e97a1cd8f5f24070e820f21d976eaeb Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Thu, 6 Dec 2007 10:21:03 +0100
Subject: ADS5121 Board: fix compile problem.

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/configs/ads5121.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h
index bb1efdf..58060a8 100644
--- a/include/configs/ads5121.h
+++ b/include/configs/ads5121.h
@@ -231,7 +231,7 @@
 #define CFG_I2C_SPEED		100000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F
 #if 0
-#define CFG_I2C_NOPROBES	{{0,0x69}}	* Don't probe these addrs */
+#define CFG_I2C_NOPROBES	{{0,0x69}}	/* Don't probe these addrs */
 #endif
 
 /*
-- 
cgit v1.1


From 7cfc12a7dcfdb350e2ab76db4dafcc30f7e77c2b Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Sat, 8 Dec 2007 14:47:34 +0100
Subject: ppc4xx: 405EX: Correctly enable USB pins

This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h |  4 ++--
 include/configs/makalu.h  | 16 ++++++++--------
 2 files changed, 10 insertions(+), 10 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 98d745c..e3f24a44 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -447,8 +447,8 @@
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
-{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
-{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index e04efb7..2871a6c 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -342,18 +342,18 @@
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO1	EBC_DATA_PAR(1)			*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO2	EBC_DATA_PAR(2)			*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO3	EBC_DATA_PAR(3)			*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4	EBC_DATA(20)	USB2_DATA(4)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO4	EBC_DATA(20)	USB2_DATA(4)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	CS(1)/NFCE(1)	IRQ(7)		*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	CS(2)/NFCE(2)	IRQ(8)		*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3)	IRQ(9)		*/	\
 {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
+{GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
-- 
cgit v1.1


From addce57e2e4c49e77ffb2020a84690713bb18b47 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Mon, 26 Nov 2007 17:12:24 -0600
Subject: Update MPC8544DS to use libfdt

Updated the MPC8544DS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8544DS.h | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 13e2a2c..fc0b9c2 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -251,13 +251,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,8544@0"
-#define OF_SOC			"soc8544@e0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH		"/soc8544@e0000000/serial@4500"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
-- 
cgit v1.1


From 50c03c8cf494d91cdec39670d95337c743e16ec9 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Tue, 27 Nov 2007 22:42:34 -0600
Subject: Update MPC8544 DS config

* Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2
* Removed some misc environment setup
* Moved to using fdtfile & fdtaddr as fdt env var names
* Enabled CONFIG_CMDLINE_EDITING

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8544DS.h | 107 +++++---------------------------------------
 1 file changed, 12 insertions(+), 95 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index fc0b9c2..aeac35a 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -422,6 +422,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
@@ -471,10 +472,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_ETHADDR	00:E0:0C:02:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR	00:E0:0C:02:01:FD
-#define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR	00:E0:0C:02:02:FD
-#define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR	00:E0:0C:02:03:FD
 #endif
 
 #define CONFIG_IPADDR	192.168.1.251
@@ -484,8 +481,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_BOOTFILE	8544ds/uImage.uboot
 #define CONFIG_UBOOTPATH	8544ds/u-boot.bin	/* TFTP server */
 
-#define CONFIG_SERVERIP	192.168.0.1
-#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP	192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
 #define CONFIG_NETMASK	255.255.0.0
 
 #define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
@@ -495,65 +492,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_BAUDRATE	115200
 
-#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
-#define PCIE_ENV \
- "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
-	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
- "pcieerr=md ${a}020 1; md ${a}e00 e;"		\
-	"pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"	\
-	"pci d.w $b.0 56 1;"			\
-	"pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \
- "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;"	\
-	"pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \
-	"pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \
-	"pci w $b.0 130 ffffffff\0" \
- "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"	\
- "pcie1regs=setenv a e000a; run pciereg\0"	\
- "pcie2regs=setenv a e0009; run pciereg\0"	\
- "pcie3regs=setenv a e000b; run pciereg\0"	\
- "pcie1cfg=setenv b 3; run pciecfg\0" \
- "pcie2cfg=setenv b 5; run pciecfg\0" \
- "pcie3cfg=setenv b 0; run pciecfg\0" \
- "pcie1err=setenv a e000a; setenv b 3; run pcieerr\0"	\
- "pcie2err=setenv a e0009; setenv b 5; run pcieerr\0"	\
- "pcie3err=setenv a e000b; setenv b 0; run pcieerr\0"	\
- "pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0"	\
- "pcie2errc=setenv a e0009; setenv b 5; run pcieerrc\0"	\
- "pcie3errc=setenv a e000b; setenv b 0; run pcieerrc\0"
-#else
-#define	PCIE_ENV ""
-#endif
-
-#if defined(CONFIG_PCI1)
-#define PCI_ENV \
- "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
-	"echo e;md ${a}e00 9\0"			\
- "pci1regs=setenv a e0008; run pcireg\0"	\
- "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
-	"pci d.w $b.0 56 1\0"			\
- "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \
-	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0"		\
- "pci1err=setenv a e0008; setenv b 7; run pcierr\0"		\
- "pci1errc=setenv a e0008; setenv b 7; run pcierrc\0"
-#else
-#define	PCI_ENV ""
-#endif
-
-#if defined(CONFIG_TSEC_ENET)
-#define ENET_ENV \
- "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
-	"md ${a}098 2\0" \
- "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \
- "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \
- "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
-	"echo mib;md ${a}680 31\0" \
- "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
- "enet1regs=setenv a e0024; run enetreg\0" \
- "enet3regs=setenv a e0026; run enetreg\0"
-#else
-#define ENET_ENV ""
-#endif
-
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
  "netdev=eth0\0"						\
  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
@@ -566,29 +504,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  "consoledev=ttyS0\0"				\
  "ramdiskaddr=2000000\0"			\
  "ramdiskfile=8544ds/ramdisk.uboot\0"		\
- "dtbaddr=c00000\0"				\
- "dtbfile=8544ds/mpc8544ds.dtb\0"		\
- "bdev=sda3\0"					\
- "eoi=mw e00400b0 0\0"				\
- "iack=md e00400a0 1\0"				\
- "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
-	"md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
- "ddrregs=setenv a e0002; run ddrreg\0"		\
- "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
-	"md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0"	\
- "guregs=setenv a e00e0; run gureg\0"		\
- "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
- "ecmregs=setenv a e0001; run ecmreg\0"		\
- "lawregs=md e0000c08 4b\0" \
- "lbcregs=md e0005000 36\0" \
- "dma0regs=md e0021100 12\0" \
- "dma1regs=md e0021180 12\0" \
- "dma2regs=md e0021200 12\0" \
- "dma3regs=md e0021280 12\0" \
- PCIE_ENV	\
- PCI_ENV	\
- ENET_ENV
-
+ "fdtaddr=c00000\0"				\
+ "fdtfile=8544ds/mpc8544ds.dtb\0"		\
+ "bdev=sda3\0"
 
 #define CONFIG_NFSBOOTCOMMAND		\
  "setenv bootargs root=/dev/nfs rw "	\
@@ -596,23 +514,22 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
  "console=$consoledev,$baudrate $othbootargs;"	\
  "tftp $loadaddr $bootfile;"		\
- "tftp $dtbaddr $dtbfile;"		\
- "bootm $loadaddr - $dtbaddr"
-
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr - $fdtaddr"
 
 #define CONFIG_RAMBOOTCOMMAND		\
  "setenv bootargs root=/dev/ram rw "	\
  "console=$consoledev,$baudrate $othbootargs;"	\
  "tftp $ramdiskaddr $ramdiskfile;"	\
  "tftp $loadaddr $bootfile;"		\
- "tftp $dtbaddr $dtbfile;"		\
- "bootm $loadaddr $ramdiskaddr $dtbaddr"
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
 
 #define CONFIG_BOOTCOMMAND		\
  "setenv bootargs root=/dev/$bdev rw "	\
  "console=$consoledev,$baudrate $othbootargs;"	\
  "tftp $loadaddr $bootfile;"		\
- "tftp $dtbaddr $dtbfile;"		\
- "bootm $loadaddr - $dtbaddr"
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr - $fdtaddr"
 
 #endif	/* __CONFIG_H */
-- 
cgit v1.1


From 5ce715802f6c50dc78b3405b92f184b1e3710519 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Wed, 28 Nov 2007 22:40:31 -0600
Subject: Update MPC8560 ADS to use libfdt

Updated the MPC8560 ADS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8560ADS.h | 12 +++++-------
 1 file changed, 5 insertions(+), 7 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index a8f362f..a24ac15 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -289,13 +289,9 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,8560@0"
-#define OF_SOC			"soc8560@e0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH		"/soc8560@e0000000/serial@4500"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 /*
  * I2C
@@ -525,6 +521,8 @@
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
 #define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif
 
 #define CONFIG_IPADDR    192.168.1.253
-- 
cgit v1.1


From 0fd5ec66b10521a057ad73e69ab5f0f9eafba255 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Wed, 28 Nov 2007 22:54:27 -0600
Subject: Update MPC8540 ADS to use libfdt

Updated the MPC8540 ADS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8540ADS.h | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index be603ac..006644d 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -298,13 +298,9 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,8540@0"
-#define OF_SOC			"soc8540@e0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH		"/soc8540@e0000000/serial@4500"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 #define CFG_64BIT_VSPRINTF	1
 #define CFG_64BIT_STRTOUL	1
-- 
cgit v1.1


From b90d25497625b90ffa3f2911a0895ca237556ff5 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Thu, 29 Nov 2007 00:11:44 -0600
Subject: Update MPC85xx CDS to use libfdt

Updated the MPC85xx CDS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8541CDS.h | 11 +++--------
 include/configs/MPC8548CDS.h | 11 +++--------
 include/configs/MPC8555CDS.h | 11 +++--------
 3 files changed, 9 insertions(+), 24 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index 8dda665..fc1b367 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -309,14 +309,9 @@ extern unsigned long get_clock_freq(void);
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,8541@0"
-#define OF_SOC			"soc8541@e0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH		"/soc8541@e0000000/serial@4600"
-#define OF_PCI			"pci@e0008000"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 /*
  * I2C
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 4edc7fd..95256f7 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -333,14 +333,9 @@ extern unsigned long get_clock_freq(void);
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,8548@0"
-#define OF_SOC			"soc8548@e0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH		"/soc8548@e0000000/serial@4600"
-#define OF_PCI			"pci@e0008000"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 /*
  * I2C
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index c414bf0..76631c6 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -309,14 +309,9 @@ extern unsigned long get_clock_freq(void);
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,8555@0"
-#define OF_SOC			"soc8555@e0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH		"/soc8555@e0000000/serial@4600"
-#define OF_PCI			"pci@e0008000"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 /*
  * I2C
-- 
cgit v1.1


From 1563f56e0c68f6920f956382d6d13bee3f01c0f7 Mon Sep 17 00:00:00 2001
From: Haiying Wang <Haiying.Wang@freescale.com>
Date: Wed, 14 Nov 2007 15:52:06 -0500
Subject: Add PCI Express support on MPC8568MDS

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8568MDS.h | 25 ++++++++++++++++++-------
 1 file changed, 18 insertions(+), 7 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index b9366cc..cf79257 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -33,7 +33,10 @@
 #define CONFIG_MPC8568		1	/* MPC8568 specific */
 #define CONFIG_MPC8568MDS	1	/* MPC8568MDS board specific */
 
-#define CONFIG_PCI
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCI1		1	/* PCI controller */
+#define CONFIG_PCIE1		1	/* PCIE controller */
+#define CONFIG_FSL_PCI_INIT	1	/* use common fsl pci init code */
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
 #define CONFIG_QE			/* Enable QE */
 #define CONFIG_ENV_OVERWRITE
@@ -87,6 +90,9 @@ extern unsigned long get_clock_freq(void);
 #define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
+#define CFG_PCI1_ADDR           (CFG_CCSRBAR+0x8000)
+#define CFG_PCIE1_ADDR          (CFG_CCSRBAR+0xa000)
+
 /*
  * DDR Setup
  */
@@ -325,12 +331,12 @@ extern unsigned long get_clock_freq(void);
 #define CFG_PCI1_IO_PHYS	0xe2000000
 #define CFG_PCI1_IO_SIZE	0x00800000	/* 8M */
 
-#define CFG_PEX_MEM_BASE	0xa0000000
-#define CFG_PEX_MEM_PHYS	CFG_PEX_MEM_BASE
-#define CFG_PEX_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PEX_IO_BASE		0x00000000
-#define CFG_PEX_IO_PHYS		0xe2800000
-#define CFG_PEX_IO_SIZE		0x00800000	/* 8M */
+#define CFG_PCIE1_MEM_BASE	0xa0000000
+#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCIE1_IO_BASE	0x00000000
+#define CFG_PCIE1_IO_PHYS	0xe2800000
+#define CFG_PCIE1_IO_SIZE	0x00800000	/* 8M */
 
 #define CFG_SRIO_MEM_BASE	0xc0000000
 
@@ -383,6 +389,11 @@ extern unsigned long get_clock_freq(void);
 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
 
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS      0x00000000
+#define CFG_PCI_MEMORY_PHYS     0x00000000
+#define CFG_PCI_MEMORY_SIZE     0x80000000
+
 #endif	/* CONFIG_PCI */
 
 #ifndef CONFIG_NET_MULTI
-- 
cgit v1.1


From c480861bf000156e6a3e932c258db59ff2212dd3 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Thu, 29 Nov 2007 01:06:19 -0600
Subject: Update MPC8568 MDS to use libfdt

Updated the MPC8568 MDS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8568MDS.h | 11 +++--------
 1 file changed, 3 insertions(+), 8 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index cf79257..2f4bc70 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -296,14 +296,9 @@ extern unsigned long get_clock_freq(void);
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,8568@0"
-#define OF_SOC			"soc8568@e0000000"
-#define OF_QE			"qe@e0080000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH		"/soc8568@e0000000/serial@4500"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 /*
  * I2C
-- 
cgit v1.1


From 22abb2d2eaf7b795a6923c6273ec9cb53fda9a10 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Thu, 29 Nov 2007 10:34:28 -0600
Subject: Update Freescale MPC85xx ADS/CDS/MDS board config

* Removed some misc environment setup
* Enabled CONFIG_CMDLINE_EDITING

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8540ADS.h |  1 +
 include/configs/MPC8541CDS.h |  1 +
 include/configs/MPC8548CDS.h | 90 +-------------------------------------------
 include/configs/MPC8555CDS.h |  1 +
 include/configs/MPC8560ADS.h |  1 +
 include/configs/MPC8568MDS.h |  1 +
 6 files changed, 7 insertions(+), 88 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 006644d..55510f3 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -437,6 +437,7 @@
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index fc1b367..d7eb5fa 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -429,6 +429,7 @@ extern unsigned long get_clock_freq(void);
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 95256f7..eace283 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -490,6 +490,7 @@ extern unsigned long get_clock_freq(void);
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
@@ -563,72 +564,6 @@ extern unsigned long get_clock_freq(void);
 
 #define CONFIG_BAUDRATE	115200
 
-#if defined(CONFIG_PCIE1)
-#define PCIE_ENV \
- "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
-	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
- "pcieerr=md ${a}020 1; md ${a}e00 e; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
-	"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \
-	"pci d $b.0 130 1\0" \
- "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;" \
-	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;"\
-	"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \
- "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
- "pcie1regs=setenv a e000a; run pciereg\0" \
- "pcie1cfg=setenv b 3; run pciecfg\0" \
- "pcie1err=setenv a e000a; setenv b 3; run pcieerr\0" \
- "pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0"
-#else
-#define	PCIE_ENV ""
-#endif
-
-#if defined(CONFIG_PCI1) || defined(CONFIG_PCI2)
-#define PCI_ENV \
- "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
-	"echo e;md ${a}e00 9\0" \
- "pcierr=md ${a}e00 8; pci d.b $b.0 7 1;pci d.w $b.0 1e 1;" \
-	"pci d.w $b.0 56 1\0" \
- "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \
-	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0"
-#else
-#define	PCI_ENV ""
-#endif
-
-#if defined(CONFIG_PCI1)
-#define PCI_ENV1 \
- "pci1regs=setenv a e0008; run pcireg\0" \
- "pci1err=setenv a e0008; setenv b 0; run pcierr\0" \
- "pci1errc=setenv a e0008; setenv b 0; run pcierrc\0"
-#else
-#define	PCI_ENV1 ""
-#endif
-
-#if defined(CONFIG_PCI2)
-#define PCI_ENV2 \
- "pci2regs=setenv a e0009; run pcireg\0" \
- "pci2err=setenv a e0009; setenv b 123; run pcierr\0"	\
- "pci2errc=setenv a e0009; setenv b 123; run pcierrc\0"
-#else
-#define	PCI_ENV2 ""
-#endif
-
-#if defined(CONFIG_TSEC_ENET)
-#define ENET_ENV \
- "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
-	"md ${a}098 2\0" \
- "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \
- "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \
- "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
-	"echo mib;md ${a}680 31\0" \
- "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
- "enet1regs=setenv a e0024; run enetreg\0" \
- "enet2regs=setenv a e0025; run enetreg\0" \
- "enet3regs=setenv a e0026; run enetreg\0" \
- "enet4regs=setenv a e0027; run enetreg\0"
-#else
-#define ENET_ENV ""
-#endif
-
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
  "netdev=eth0\0"						\
  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
@@ -642,28 +577,7 @@ extern unsigned long get_clock_freq(void);
  "ramdiskaddr=2000000\0"			\
  "ramdiskfile=ramdisk.uboot\0"			\
  "fdtaddr=c00000\0"				\
- "fdtfile=mpc8548cds.dtb\0"			\
- "eoi=mw e00400b0 0\0"				\
- "iack=md e00400a0 1\0"				\
- "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
-	"md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
- "ddrregs=setenv a e0002; run ddrreg\0"		\
- "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
-	"md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0"	\
- "guregs=setenv a e00e0; run gureg\0"		\
- "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
- "ecmregs=setenv a e0001; run ecmreg\0" \
- "lawregs=md e0000c08 4b\0" \
- "lbcregs=md e0005000 36\0" \
- "dma0regs=md e0021100 12\0" \
- "dma1regs=md e0021180 12\0" \
- "dma2regs=md e0021200 12\0" \
- "dma3regs=md e0021280 12\0" \
- PCIE_ENV \
- PCI_ENV \
- PCI_ENV1 \
- PCI_ENV2 \
- ENET_ENV
+ "fdtfile=mpc8548cds.dtb\0"
 
 #define CONFIG_NFSBOOTCOMMAND						\
    "setenv bootargs root=/dev/nfs rw "					\
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 76631c6..8ae4ef0 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -429,6 +429,7 @@ extern unsigned long get_clock_freq(void);
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index a24ac15..cdd8ad4 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -467,6 +467,7 @@
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CFG_LOAD_ADDR	0x1000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 2f4bc70..2cf48fb 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -458,6 +458,7 @@ extern unsigned long get_clock_freq(void);
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
-- 
cgit v1.1


From 82ac8c97145a4c3bf8b3dbfad00fa96e920f9b9c Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Fri, 7 Dec 2007 12:04:30 -0600
Subject: Update Freescale MPC85xx ADS/CDS/MDS board config

* Enabled CONFIG_CMD_ELF

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8540ADS.h | 1 +
 include/configs/MPC8541CDS.h | 1 +
 include/configs/MPC8544DS.h  | 1 +
 include/configs/MPC8548CDS.h | 1 +
 include/configs/MPC8555CDS.h | 1 +
 include/configs/MPC8560ADS.h | 1 +
 include/configs/MPC8568MDS.h | 1 +
 7 files changed, 7 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 55510f3..35e1d63 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -420,6 +420,7 @@
 
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
+#define CONFIG_CMD_ELF
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index d7eb5fa..d2e7237 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -417,6 +417,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index aeac35a..b8cd50b 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -406,6 +406,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index eace283..95affa5 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -478,6 +478,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 8ae4ef0..90ef3d6 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -417,6 +417,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index cdd8ad4..d4e0de0 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -446,6 +446,7 @@
 
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
+#define CONFIG_CMD_ELF
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 2cf48fb..3822c1b 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -446,6 +446,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
-- 
cgit v1.1


From 8ff3de61fc5f9b3b21647bce081a3b7f710f0d4d Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Fri, 7 Dec 2007 12:17:34 -0600
Subject: Handle MPC85xx PCIe reset errata (PCI-Ex 38)

On the MPC85xx boards that have PCIe enable the PCIe errata fix.
(MPC8544DS, MPC8548CDS, MPC8568MDS).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/configs/MPC8544DS.h  | 1 +
 include/configs/MPC8548CDS.h | 1 +
 include/configs/MPC8568MDS.h | 1 +
 3 files changed, 3 insertions(+)

(limited to 'include/configs')

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index b8cd50b..545a76c 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -40,6 +40,7 @@
 #define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
 #define CONFIG_PCIE3		1	/* PCIE controler 3 (ULI bridge) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
 
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 95affa5..3f382e5 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -42,6 +42,7 @@
 #undef CONFIG_RIO
 #undef CONFIG_PCI2
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
 
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 3822c1b..59f490e 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -37,6 +37,7 @@
 #define CONFIG_PCI1		1	/* PCI controller */
 #define CONFIG_PCIE1		1	/* PCIE controller */
 #define CONFIG_FSL_PCI_INIT	1	/* use common fsl pci init code */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
 #define CONFIG_QE			/* Enable QE */
 #define CONFIG_ENV_OVERWRITE
-- 
cgit v1.1


From 667568db157f374b85abd7e03596ddd1f0b25681 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Mon, 29 Oct 2007 13:02:54 +0100
Subject: AVR32: Add support for the ATSTK1003 board

ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 include/configs/atstk1003.h | 184 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 184 insertions(+)
 create mode 100644 include/configs/atstk1003.h

(limited to 'include/configs')

diff --git a/include/configs/atstk1003.h b/include/configs/atstk1003.h
new file mode 100644
index 0000000..194788b
--- /dev/null
+++ b/include/configs/atstk1003.h
@@ -0,0 +1,184 @@
+/*
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * Configuration settings for the ATSTK1003 CPU daughterboard
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_AVR32			1
+#define CONFIG_AT32AP			1
+#define CONFIG_AT32AP7001		1
+#define CONFIG_ATSTK1003		1
+#define CONFIG_ATSTK1000		1
+
+#define CONFIG_ATSTK1000_EXT_FLASH	1
+
+/*
+ * Timer clock frequency. We're using the CPU-internal COUNT register
+ * for this, so this is equivalent to the CPU core clock frequency
+ */
+#define CFG_HZ				1000
+
+/*
+ * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
+ * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the
+ * PLL frequency.
+ * (CFG_OSC0_HZ * CFG_PLL0_MUL) / CFG_PLL0_DIV = PLL MHz
+ */
+#define CONFIG_PLL			1
+#define CFG_POWER_MANAGER		1
+#define CFG_OSC0_HZ			20000000
+#define CFG_PLL0_DIV			1
+#define CFG_PLL0_MUL			7
+#define CFG_PLL0_SUPPRESS_CYCLES	16
+/*
+ * Set the CPU running at:
+ * PLL / (2^CFG_CLKDIV_CPU) = CPU MHz
+ */
+#define CFG_CLKDIV_CPU			0
+/*
+ * Set the HSB running at:
+ * PLL / (2^CFG_CLKDIV_HSB) = HSB MHz
+ */
+#define CFG_CLKDIV_HSB			1
+/*
+ * Set the PBA running at:
+ * PLL / (2^CFG_CLKDIV_PBA) = PBA MHz
+ */
+#define CFG_CLKDIV_PBA			2
+/*
+ * Set the PBB running at:
+ * PLL / (2^CFG_CLKDIV_PBB) = PBB MHz
+ */
+#define CFG_CLKDIV_PBB			1
+
+/*
+ * The PLLOPT register controls the PLL like this:
+ *   icp = PLLOPT<2>
+ *   ivco = PLLOPT<1:0>
+ *
+ * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
+ */
+#define CFG_PLL0_OPT			0x04
+
+#undef CONFIG_USART0
+#define CONFIG_USART1			1
+#undef CONFIG_USART2
+#undef CONFIG_USART3
+
+/* User serviceable stuff */
+#define CONFIG_DOS_PARTITION		1
+
+#define CONFIG_CMDLINE_TAG		1
+#define CONFIG_SETUP_MEMORY_TAGS	1
+#define CONFIG_INITRD_TAG		1
+
+#define CONFIG_STACKSIZE		(2048)
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_BOOTARGS							\
+	"console=ttyS0 root=/dev/mmcblk0p1 rootwait"
+
+#define CONFIG_BOOTCOMMAND						\
+	"mmcinit; ext2load mmc 0:1 0x10400000 /boot/uImage; bootm"
+
+/*
+ * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
+ * data on the serial line may interrupt the boot sequence.
+ */
+#define CONFIG_BOOTDELAY		1
+#define CONFIG_AUTOBOOT			1
+#define CONFIG_AUTOBOOT_KEYED		1
+#define CONFIG_AUTOBOOT_PROMPT				\
+	"Press SPACE to abort autoboot in %d seconds\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"d"
+#define CONFIG_AUTOBOOT_STOP_STR	" "
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MMC
+
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_XIMG
+
+#define CONFIG_ATMEL_USART		1
+#define CONFIG_PIO2			1
+#define CFG_HSDRAMC			1
+#define CONFIG_MMC			1
+
+#define CFG_DCACHE_LINESZ		32
+#define CFG_ICACHE_LINESZ		32
+
+#define CONFIG_NR_DRAM_BANKS		1
+
+/* External flash on STK1000 */
+#if 0
+#define CFG_FLASH_CFI			1
+#define CFG_FLASH_CFI_DRIVER		1
+#endif
+
+#define CFG_FLASH_BASE			0x00000000
+#define CFG_FLASH_SIZE			0x800000
+#define CFG_MAX_FLASH_BANKS		1
+#define CFG_MAX_FLASH_SECT		135
+
+#define CFG_MONITOR_BASE		CFG_FLASH_BASE
+
+#define CFG_INTRAM_BASE			0x24000000
+#define CFG_INTRAM_SIZE			0x8000
+
+#define CFG_SDRAM_BASE			0x10000000
+
+#define CFG_ENV_IS_IN_FLASH		1
+#define CFG_ENV_SIZE			65536
+#define CFG_ENV_ADDR			(CFG_FLASH_BASE + CFG_FLASH_SIZE - CFG_ENV_SIZE)
+
+#define CFG_INIT_SP_ADDR		(CFG_INTRAM_BASE + CFG_INTRAM_SIZE)
+
+#define CFG_MALLOC_LEN			(256*1024)
+
+/* Allow 4MB for the kernel run-time image */
+#define CFG_LOAD_ADDR			(CFG_SDRAM_BASE + 0x00400000)
+#define CFG_BOOTPARAMS_LEN		(16 * 1024)
+
+/* Other configuration settings that shouldn't have to change all that often */
+#define CFG_PROMPT			"Uboot> "
+#define CFG_CBSIZE			256
+#define CFG_MAXARGS			16
+#define CFG_PBSIZE			(CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+#define CFG_LONGHELP			1
+
+#define CFG_MEMTEST_START		CFG_SDRAM_BASE
+#define CFG_MEMTEST_END			(CFG_MEMTEST_START + 0x700000)
+#define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
+
+#endif /* __CONFIG_H */
-- 
cgit v1.1


From 64ff2357b1727213803591813dbc779c924bf772 Mon Sep 17 00:00:00 2001
From: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Mon, 29 Oct 2007 13:02:54 +0100
Subject: AVR32: Add support for the ATSTK1004 board

ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
---
 include/configs/atstk1004.h | 185 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 185 insertions(+)
 create mode 100644 include/configs/atstk1004.h

(limited to 'include/configs')

diff --git a/include/configs/atstk1004.h b/include/configs/atstk1004.h
new file mode 100644
index 0000000..1bad171
--- /dev/null
+++ b/include/configs/atstk1004.h
@@ -0,0 +1,185 @@
+/*
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * Configuration settings for the ATSTK1003 CPU daughterboard
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_AVR32			1
+#define CONFIG_AT32AP			1
+#define CONFIG_AT32AP7002		1
+#define CONFIG_ATSTK1004		1
+#define CONFIG_ATSTK1000		1
+
+#define CONFIG_ATSTK1000_EXT_FLASH	1
+
+/*
+ * Timer clock frequency. We're using the CPU-internal COUNT register
+ * for this, so this is equivalent to the CPU core clock frequency
+ */
+#define CFG_HZ				1000
+
+/*
+ * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
+ * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the
+ * PLL frequency.
+ * (CFG_OSC0_HZ * CFG_PLL0_MUL) / CFG_PLL0_DIV = PLL MHz
+ */
+#define CONFIG_PLL			1
+#define CFG_POWER_MANAGER		1
+#define CFG_OSC0_HZ			20000000
+#define CFG_PLL0_DIV			1
+#define CFG_PLL0_MUL			7
+#define CFG_PLL0_SUPPRESS_CYCLES	16
+/*
+ * Set the CPU running at:
+ * PLL / (2^CFG_CLKDIV_CPU) = CPU MHz
+ */
+#define CFG_CLKDIV_CPU			0
+/*
+ * Set the HSB running at:
+ * PLL / (2^CFG_CLKDIV_HSB) = HSB MHz
+ */
+#define CFG_CLKDIV_HSB			1
+/*
+ * Set the PBA running at:
+ * PLL / (2^CFG_CLKDIV_PBA) = PBA MHz
+ */
+#define CFG_CLKDIV_PBA			2
+/*
+ * Set the PBB running at:
+ * PLL / (2^CFG_CLKDIV_PBB) = PBB MHz
+ */
+#define CFG_CLKDIV_PBB			1
+
+/*
+ * The PLLOPT register controls the PLL like this:
+ *   icp = PLLOPT<2>
+ *   ivco = PLLOPT<1:0>
+ *
+ * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
+ */
+#define CFG_PLL0_OPT			0x04
+
+#undef CONFIG_USART0
+#define CONFIG_USART1			1
+#undef CONFIG_USART2
+#undef CONFIG_USART3
+
+/* User serviceable stuff */
+#define CONFIG_DOS_PARTITION		1
+
+#define CONFIG_CMDLINE_TAG		1
+#define CONFIG_SETUP_MEMORY_TAGS	1
+#define CONFIG_INITRD_TAG		1
+
+#define CONFIG_STACKSIZE		(2048)
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_BOOTARGS							\
+	"console=ttyS0 root=/dev/mmcblk0p1 rootwait"
+
+#define CONFIG_BOOTCOMMAND						\
+	"mmcinit; ext2load mmc 0:1 0x10200000 /boot/uImage; bootm"
+
+/*
+ * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
+ * data on the serial line may interrupt the boot sequence.
+ */
+#define CONFIG_BOOTDELAY		1
+#define CONFIG_AUTOBOOT			1
+#define CONFIG_AUTOBOOT_KEYED		1
+#define CONFIG_AUTOBOOT_PROMPT				\
+	"Press SPACE to abort autoboot in %d seconds\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"d"
+#define CONFIG_AUTOBOOT_STOP_STR	" "
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MMC
+
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_XIMG
+
+#define CONFIG_ATMEL_USART		1
+#define CONFIG_PIO2			1
+#define CFG_HSDRAMC			1
+#define CONFIG_MMC			1
+
+#define CFG_DCACHE_LINESZ		32
+#define CFG_ICACHE_LINESZ		32
+
+#define CONFIG_NR_DRAM_BANKS		1
+
+/* External flash on STK1000 */
+#if 0
+#define CFG_FLASH_CFI			1
+#define CFG_FLASH_CFI_DRIVER		1
+#endif
+
+#define CFG_FLASH_BASE			0x00000000
+#define CFG_FLASH_SIZE			0x800000
+#define CFG_MAX_FLASH_BANKS		1
+#define CFG_MAX_FLASH_SECT		135
+
+#define CFG_MONITOR_BASE		CFG_FLASH_BASE
+
+#define CFG_INTRAM_BASE			0x24000000
+#define CFG_INTRAM_SIZE			0x8000
+
+#define CFG_SDRAM_BASE			0x10000000
+#define CFG_SDRAM_16BIT			1
+
+#define CFG_ENV_IS_IN_FLASH		1
+#define CFG_ENV_SIZE			65536
+#define CFG_ENV_ADDR			(CFG_FLASH_BASE + CFG_FLASH_SIZE - CFG_ENV_SIZE)
+
+#define CFG_INIT_SP_ADDR		(CFG_INTRAM_BASE + CFG_INTRAM_SIZE)
+
+#define CFG_MALLOC_LEN			(256*1024)
+
+/* Allow 4MB for the kernel run-time image */
+#define CFG_LOAD_ADDR			(CFG_SDRAM_BASE + 0x00200000)
+#define CFG_BOOTPARAMS_LEN		(16 * 1024)
+
+/* Other configuration settings that shouldn't have to change all that often */
+#define CFG_PROMPT			"Uboot> "
+#define CFG_CBSIZE			256
+#define CFG_MAXARGS			16
+#define CFG_PBSIZE			(CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+#define CFG_LONGHELP			1
+
+#define CFG_MEMTEST_START		CFG_SDRAM_BASE
+#define CFG_MEMTEST_END			(CFG_MEMTEST_START + 0x700000)
+#define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
+
+#endif /* __CONFIG_H */
-- 
cgit v1.1


From 61fb15c516fef5631e305f1976d7b3a679725856 Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Thu, 27 Dec 2007 01:52:50 +0100
Subject: Fix coding style issues; update CHANGELOG.

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/configs/ms7722se.h | 11 +++++------
 include/configs/ms7750se.h |  6 +++---
 2 files changed, 8 insertions(+), 9 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h
index 18e9851..ae0d018 100644
--- a/include/configs/ms7722se.h
+++ b/include/configs/ms7722se.h
@@ -25,7 +25,7 @@
 #ifndef __MS7722SE_H
 #define __MS7722SE_H
 
-#undef DEBUG 
+#undef DEBUG
 #define CONFIG_SH		1
 #define CONFIG_SH4		1
 #define CONFIG_CPU_SH7722	1
@@ -56,7 +56,6 @@
 /* MEMORY */
 #define MS7722SE_SDRAM_BASE	(0x8C000000)
 #define MS7722SE_FLASH_BASE_1	(0xA0000000)
-//#define MS7722SE_FLASH_BASE_1	(0xA1000000)
 #define MS7722SE_FLASH_BANK_SIZE	(8*1024 * 1024)
 
 #define CFG_LONGHELP				/* undef to save memory	*/
@@ -87,12 +86,12 @@
 
 #define CFG_LOAD_ADDR	(CFG_SDRAM_BASE + 4 * 1024 * 1024)	/* default load address for scripts ?!? */
 
-#define CFG_MONITOR_BASE	(MS7722SE_FLASH_BASE_1)	/* Address of u-boot image 
+#define CFG_MONITOR_BASE	(MS7722SE_FLASH_BASE_1)	/* Address of u-boot image
 						   	in Flash (NOT run time address in SDRAM) ?!? */
 #define CFG_MONITOR_LEN	(128 * 1024)		/* */
 #define CFG_MALLOC_LEN	(256 * 1024)		/* Size of DRAM reserved for malloc() use */
 #define CFG_GBL_DATA_SIZE	(256)		/* size in bytes reserved for initial data */
-#define CFG_BOOTMAPSZ	(8 * 1024 * 1024)	
+#define CFG_BOOTMAPSZ	(8 * 1024 * 1024)
 
 /* FLASH */
 #define CFG_FLASH_CFI
@@ -102,7 +101,7 @@
 
 #define CFG_FLASH_BASE		(MS7722SE_FLASH_BASE_1)	/* Physical start address of Flash memory */
 
-#define CFG_MAX_FLASH_SECT	150		/* Max number of sectors on each 
+#define CFG_MAX_FLASH_SECT	150		/* Max number of sectors on each
 				   			Flash chip */
 
 /* if you use all NOR Flash , you change dip-switch. Please see MS7722SE01 Manual. */
@@ -131,7 +130,7 @@
 
 /* Board Clock */
 #define CONFIG_SYS_CLK_FREQ	33333333
-#define TMU_CLK_DIVIDER		(4)	/* 4 (default), 16, 64, 256 or 1024 */		
+#define TMU_CLK_DIVIDER		(4)	/* 4 (default), 16, 64, 256 or 1024 */
 #define CFG_HZ			(CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER)
 
 #endif	/* __MS7722SE_H */
diff --git a/include/configs/ms7750se.h b/include/configs/ms7750se.h
index 7925f20..3668156 100644
--- a/include/configs/ms7750se.h
+++ b/include/configs/ms7750se.h
@@ -37,7 +37,7 @@
 /*
  * Command line configuration.
  */
-//#include <config_cmd_default.h>
+/*#include <config_cmd_default.h>*/
 
 #define CONFIG_CMD_DFL
 #define CONFIG_CMD_FLASH
@@ -56,7 +56,7 @@
 #define CFG_SDRAM_BASE		(0x8C000000)
 #define CFG_SDRAM_SIZE		(64 * 1024 * 1024)
 
-#define CFG_LONGHELP		
+#define CFG_LONGHELP
 #define CFG_PROMPT		"=> "
 #define CFG_CBSIZE		256
 #define CFG_PBSIZE		256
@@ -71,7 +71,7 @@
 /* NOR Flash */
 /* #define CFG_FLASH_BASE		(0xA1000000)*/
 #define CFG_FLASH_BASE		(0xA0000000)
-#define CFG_MAX_FLASH_BANKS	(1)	/* Max number of 
+#define CFG_MAX_FLASH_BANKS	(1)	/* Max number of
 				 	 * Flash memory banks
 				 	 */
 #define CFG_MAX_FLASH_SECT	142
-- 
cgit v1.1


From dabad4b9bc46908e301f73ce76b38b23626a96e9 Mon Sep 17 00:00:00 2001
From: Jens Gehrlein <jens.gehrlein@tqs.de>
Date: Thu, 27 Sep 2007 14:54:46 +0200
Subject: TQM860M: Support for 10col SDRAMs, max. 128 MiB

Signed-off-by: Martin Krause <martin.krause@tqs.de>
---
 include/configs/TQM860M.h | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
index fe3a2f0..44ad53e 100644
--- a/include/configs/TQM860M.h
+++ b/include/configs/TQM860M.h
@@ -368,7 +368,7 @@
  */
 #define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
 #define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
+#define	SDRAM_MAX_SIZE		0x08000000	/* max 128 MB per bank	*/
 
 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
 #define CFG_OR_TIMING_SDRAM	0x00000A00
@@ -444,7 +444,10 @@
 #define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 
 /*
  * Internal Definitions
-- 
cgit v1.1


From 492c7049869348d31168de8dad89651315e468e0 Mon Sep 17 00:00:00 2001
From: Jens Gehrlein <jens.gehrlein@tqs.de>
Date: Thu, 27 Sep 2007 14:54:46 +0200
Subject: TQM885D: fix SDRAM refresh

At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 128. This result
in a refresh rate of 4 * 7.8 us at the default clock
66 MHz. At 133 MHz the value will be then 4 * 3.8 us.
This is a compromise until a new method is found to
adjust the refresh rate.

Signed-off-by: Martin Krause <martin.krause@tqs.de>
---
 include/configs/TQM885D.h | 36 ++++++++++++++++++++----------------
 1 file changed, 20 insertions(+), 16 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
index f36b729..a8fbbfb 100644
--- a/include/configs/TQM885D.h
+++ b/include/configs/TQM885D.h
@@ -434,26 +434,30 @@
 #define CFG_PTA_PER_CLK	((4096 * 64 * 1000) / (4 * 64))
 
 /*
- * Memory Periodic Timer Prescaler
- * Periodic timer for refresh, start with refresh rate for 40 MHz clock
- * (CFG_8xx_CPUCLK_MIN / CFG_PTA_PER_CLK)
+ * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
+ *
+ *                        CPUclock(MHz) * 31.2
+ * CFG_MAMR_PTA = -----------------------------------     with DFBRG = 0
+ *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
+ *
+ * CPU clock =  15 MHz:  CFG_MAMR_PTA =  29   ->  4 * 7.73 us
+ * CPU clock =  50 MHz:  CFG_MAMR_PTA =  97   ->  4 * 7.76 us
+ * CPU clock =  66 MHz:  CFG_MAMR_PTA = 128   ->  4 * 7.75 us
+ * CPU clock = 133 MHz:  CFG_MAMR_PTA = 255   ->  4 * 7.67 us
+ *
+ * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
+ * be met also in the default configuration, i.e. if environment variable
+ * 'cpuclk' is not set.
  */
-#define CFG_MAMR_PTA		39
+#define CFG_MAMR_PTA		128
 
 /*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CFG_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CFG_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
+ * Memory Periodic Timer Prescaler Register (MPTPR) values.
  */
-#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
+/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
+#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16
+/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
+#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8
 
 /*
  * MAMR settings for SDRAM
-- 
cgit v1.1


From b988b8cd443989be65161888eea0127ad03f846f Mon Sep 17 00:00:00 2001
From: Martin Krause <martin.krause@tqs.de>
Date: Wed, 26 Sep 2007 17:55:56 +0200
Subject: TQM885D: use calculated cpuclk instead of measuring it

On the TQM885D the measurement of cpuclk with the PIT reference
timer ist not necessary. Since all module variants use the same
external 10 MHz oscillator, the cpuclk only depends on the PLL
configuration - which is readable by software.

Signed-off-by: Martin Krause <martin.krause@tqs.de>
---
 include/configs/TQM885D.h | 7 -------
 1 file changed, 7 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
index a8fbbfb..dd26d54 100644
--- a/include/configs/TQM885D.h
+++ b/include/configs/TQM885D.h
@@ -46,13 +46,6 @@
 						/* (it will be used if there is no	*/
 						/* 'cpuclk' variable with valid value)	*/
 
-#define CFG_MEASURE_CPUCLK			/* Measure real cpu clock	*/
-						/* (function measure_gclk()	*/
-						/* will be called)		*/
-#ifdef CFG_MEASURE_CPUCLK
-#define CFG_8XX_XIN		10000000	/* measure_gclk() needs this	*/
-#endif
-
 #define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 
 #define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-- 
cgit v1.1


From 22d1a56cbfb0bff34f477b4db6a55d076d829b83 Mon Sep 17 00:00:00 2001
From: Jens Gehrlein <jens.gehrlein@tqs.de>
Date: Wed, 26 Sep 2007 17:55:54 +0200
Subject: TQM885D: Exchanged SDRAM timing by a more relaxed timing.

CAS-Latency=2, Write Recovery Time tWR=2
The max. supported bus frequency is 66 MHz. Therefore, changed
threshold to switch from 1:1 mode to 2:1 from 80 MHz to 66 MHz.

Signed-off-by: Martin Krause <martin.krause@tqs.de>
---
 include/configs/TQM885D.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
index dd26d54..e0c6965 100644
--- a/include/configs/TQM885D.h
+++ b/include/configs/TQM885D.h
@@ -42,7 +42,7 @@
 #define CONFIG_8xx_OSCLK		10000000	/*  10 MHz - PLL input clock	*/
 #define CFG_8xx_CPUCLK_MIN		15000000	/*  15 MHz - CPU minimum clock	*/
 #define CFG_8xx_CPUCLK_MAX		133000000	/* 133 MHz - CPU maximum clock	*/
-#define CONFIG_8xx_CPUCLK_DEFAULT	66000000	/*  50 MHz - CPU default clock	*/
+#define CONFIG_8xx_CPUCLK_DEFAULT	66000000	/*  66 MHz - CPU default clock	*/
 						/* (it will be used if there is no	*/
 						/* 'cpuclk' variable with valid value)	*/
 
-- 
cgit v1.1


From 11d9eec479b470eab9242ab937fca70a876d9376 Mon Sep 17 00:00:00 2001
From: Martin Krause <martin.krause@tqs.de>
Date: Wed, 26 Sep 2007 17:55:56 +0200
Subject: TQM885D: adjust for doubled flash sector size + some minor fixes

Signed-off-by: Martin Krause <martin.krause@tqs.de>
---
 include/configs/TQM885D.h | 20 +++++++++++++-------
 1 file changed, 13 insertions(+), 7 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
index e0c6965..5bbb8e7 100644
--- a/include/configs/TQM885D.h
+++ b/include/configs/TQM885D.h
@@ -76,9 +76,15 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/TQM866M/uImage\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
+	"bootfile=/tftpboot/TQM885D/uImage\0"				\
+	"fdt_addr=400C0000\0"						\
+	"kernel_addr=40100000\0"					\
+	"ramdisk_addr=40280000\0"					\
+	"load=tftp 200000 ${u-boot}\0"					\
+	"update=protect off 40000000 +${filesize};"			\
+		"erase 40000000 +${filesize};"				\
+		"cp.b 200000 40000000 ${filesize};"			\
+		"protect on 40000000 +${filesize}\0"			\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -137,7 +143,7 @@
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 
-#undef CONFIG_RTC_MPC8xx		/* MPC866 does not support RTC	*/
+#undef CONFIG_RTC_MPC8xx		/* MPC885 does not support RTC	*/
 
 #define	CONFIG_TIMESTAMP		/* but print image timestmps	*/
 
@@ -223,7 +229,7 @@
 #define CFG_FLASH_BASE		0x40000000
 #define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_LEN		(256 << 10)	/* Reserve 128 kB for malloc()	*/
 
 /*
  * For booting Linux, the board info and command line data
@@ -243,8 +249,8 @@
 
 #define CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
-#define CFG_ENV_SIZE		0x08000 /* Total Size of Environment Sector	*/
-#define CFG_ENV_SECT_SIZE	0x20000 /* Total Size of Environment Sector	*/
+#define CFG_ENV_SIZE		0x08000 /* Total Size of Environment		*/
+#define CFG_ENV_SECT_SIZE	0x40000 /* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
-- 
cgit v1.1


From e318d9e9021a0af7508171f84ed09d0e79f0284e Mon Sep 17 00:00:00 2001
From: Martin Krause <martin.krause@tqs.de>
Date: Thu, 27 Sep 2007 11:10:08 +0200
Subject: TQM8xx: use the CFI flash driver on all TQM8xx boards

Signed-off-by: Martin Krause <martin.krause@tqs.de>
---
 include/configs/HMI10.h    | 12 ++++++++----
 include/configs/TQM823L.h  | 12 ++++++++----
 include/configs/TQM823M.h  | 14 +++++++++-----
 include/configs/TQM850L.h  | 12 ++++++++----
 include/configs/TQM850M.h  | 14 +++++++++-----
 include/configs/TQM855L.h  | 12 ++++++++----
 include/configs/TQM855M.h  | 14 +++++++++-----
 include/configs/TQM860L.h  | 12 ++++++++----
 include/configs/TQM860M.h  | 13 ++++++++-----
 include/configs/TQM862L.h  | 13 ++++++++-----
 include/configs/TQM862M.h  | 15 +++++++++------
 include/configs/TQM866M.h  | 13 ++++++++-----
 include/configs/TQM885D.h  | 12 ++++++++----
 include/configs/virtlab2.h | 12 ++++++++----
 14 files changed, 116 insertions(+), 64 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/HMI10.h b/include/configs/HMI10.h
index 02ae5d0..f8b0262 100644
--- a/include/configs/HMI10.h
+++ b/include/configs/HMI10.h
@@ -224,11 +224,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
index 7a38010..be5b4d3 100644
--- a/include/configs/TQM823L.h
+++ b/include/configs/TQM823L.h
@@ -192,11 +192,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h
index e8b6a80..a0c01b6 100644
--- a/include/configs/TQM823M.h
+++ b/include/configs/TQM823M.h
@@ -188,15 +188,19 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
 #define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h
index beeca63..f51b12e 100644
--- a/include/configs/TQM850L.h
+++ b/include/configs/TQM850L.h
@@ -179,11 +179,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h
index d5609c1..a725e71 100644
--- a/include/configs/TQM850M.h
+++ b/include/configs/TQM850M.h
@@ -177,15 +177,19 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
 #define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h
index e35b5b2..16dc3eb 100644
--- a/include/configs/TQM855L.h
+++ b/include/configs/TQM855L.h
@@ -183,11 +183,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index cd5212e..c4b4599 100644
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -217,15 +217,19 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
 #define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h
index d5838db..ac22c1e 100644
--- a/include/configs/TQM860L.h
+++ b/include/configs/TQM860L.h
@@ -186,11 +186,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
index 44ad53e..8601de1 100644
--- a/include/configs/TQM860M.h
+++ b/include/configs/TQM860M.h
@@ -189,11 +189,14 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
index f09d3d1..2bf4a2a 100644
--- a/include/configs/TQM862L.h
+++ b/include/configs/TQM862L.h
@@ -186,14 +186,17 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
-
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
 #define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
 
diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h
index 039aa3a..d42ffc9 100644
--- a/include/configs/TQM862M.h
+++ b/include/configs/TQM862M.h
@@ -186,16 +186,19 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
-
 #define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
 #define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index ca3c166..d7e5eeb 100644
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -232,11 +232,14 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
 #define CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
index 5bbb8e7..8a3aa4b 100644
--- a/include/configs/TQM885D.h
+++ b/include/configs/TQM885D.h
@@ -241,11 +241,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
 #define CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
diff --git a/include/configs/virtlab2.h b/include/configs/virtlab2.h
index edae6f4..827a28f 100644
--- a/include/configs/virtlab2.h
+++ b/include/configs/virtlab2.h
@@ -193,11 +193,15 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+/* use CFI flash driver */
+#define CFG_FLASH_CFI		1	/* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver */
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE	1
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
-- 
cgit v1.1


From 33ed73bc0e38d0f2b5c183d4629d8f207e5b9994 Mon Sep 17 00:00:00 2001
From: Martin Krause <martin.krause@tqs.de>
Date: Mon, 12 Nov 2007 10:56:17 +0100
Subject: Some configuration updates for the TQM5200 based TB5200 board:

- enable command line history
- increase malloc space (because of bigger flash sectors)

Signed-off-by: Martin Krause <martin.krause@tqs.de>
---
 include/configs/TB5200.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h
index 1c6a9ae..ae8d9ab 100644
--- a/include/configs/TB5200.h
+++ b/include/configs/TB5200.h
@@ -335,7 +335,7 @@
 #else
 #define CFG_MONITOR_LEN		(384 << 10)	/* Reserve 384 kB for Monitor	*/
 #endif /* CONFIG_TQM5200_B */
-#define CFG_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
+#define CFG_MALLOC_LEN		(1024 << 10)	/* Reserve 1024 kB for malloc()	*/
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*
@@ -392,6 +392,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory	    */
 #define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
 #if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
-- 
cgit v1.1


From 136288847e3b04f2ff357a067ad45e10afa0a24c Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Thu, 13 Dec 2007 14:52:53 +0100
Subject: ppc4xx: Bring 4xx fdt support up-to-date

This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 3 +--
 include/configs/sequoia.h | 6 ++++++
 2 files changed, 7 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index e3f24a44..bec9fde 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -519,7 +519,6 @@
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,405EX@0"
+#define OF_CPU			"cpu@0"
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 2af675a..58acbc0 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -487,4 +487,10 @@
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	    /* which serial port to use */
 #endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define OF_CPU			"cpu@0"
+
 #endif	/* __CONFIG_H */
-- 
cgit v1.1


From 052440b022ca8981d39b6f8c10d1aa6326f47480 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Markus=20Klotzb=C3=BCcher?= <mk@denx.de>
Date: Fri, 23 Nov 2007 13:09:18 +0100
Subject: ppc4xx: Add CONFIG_BOOTP_SUBNETMASK to Sequoia board config

When using dhcp/bootp the "netmask" environment variable is not
set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is
desireable, so the following patch adds this this option to the board
config.

Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/sequoia.h | 1 +
 1 file changed, 1 insertion(+)

(limited to 'include/configs')

diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 58acbc0..419ee73 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -329,6 +329,7 @@
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_SUBNETMASK
 
 
 /*
-- 
cgit v1.1


From 328a340392a5df9aaf00792be989df73e750859e Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Tue, 18 Dec 2007 08:44:51 +0100
Subject: ppc4xx: fdt: Cleanup setup of cpu node setup

Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
without using the absolute path to the cpu node. This makes it possible
to use this U-Boot version with both versions of cpu-node naming
"cpu@0" and the former "PowerPC,440EPx@0".

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/kilauea.h | 1 -
 include/configs/sequoia.h | 1 -
 2 files changed, 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index bec9fde..f3e8601 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -519,6 +519,5 @@
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
-#define OF_CPU			"cpu@0"
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 419ee73..48a64e3 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -492,6 +492,5 @@
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
-#define OF_CPU			"cpu@0"
 
 #endif	/* __CONFIG_H */
-- 
cgit v1.1


From bf8324e4a50758daff8cddd04c6a2ff8ed775bea Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Wed, 19 Dec 2007 09:05:40 +0100
Subject: ppc4xx: Add fdt support to AMCC Katmai eval board

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/katmai.h | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 2eed941..0aa4f2d 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -193,8 +193,14 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"				\
+	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
+		"tftp ${fdt_addr} ${fdt_file};"				\
+		"run nfsargs addip addtty;"				\
+		"bootm 200000 - ${fdt_addr}\0"				\
+	"rootpath=/opt/eldk/ppc_4xx\0"					\
 	"bootfile=katmai/uImage\0"					\
+	"fdt_file=katmai/katmai.dtb\0"					\
+	"fdt_addr=400000\0"						\
 	"kernel_addr=fff10000\0"					\
 	"ramdisk_addr=fff20000\0"					\
 	"initrd_high=30000000\0"					\
@@ -445,4 +451,8 @@
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
 #endif	/* __CONFIG_H */
-- 
cgit v1.1


From b0265b576bb8fa9465f99e99c323768b562fadc2 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Fri, 21 Dec 2007 07:51:29 +0100
Subject: ppc4xx: Update Makalu fdt support

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/makalu.h | 2 --
 1 file changed, 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index 2871a6c..8f8e867 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -394,6 +394,4 @@
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-#define OF_CPU			"PowerPC,405EX@0"
-
 #endif	/* __CONFIG_H */
-- 
cgit v1.1


From 42d55ea0bde06e47d5a3b49b0d91002acd8e5708 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Sat, 22 Dec 2007 12:20:09 +0100
Subject: ppc4xx: Move virtual address of POST cache test to bigger address

On Sequoia & LWMON5 the virtual address of the POST cache test is now
moved to a bigger address. This enables usage of more memory on those
boards.

Signed-off-by: Stefan Roese <sr@denx.de>
---
 include/configs/lwmon5.h  | 2 +-
 include/configs/sequoia.h | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index 9cb483d..5210024 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -153,7 +153,7 @@
 				 CFG_POST_SPR      | \
 				 CFG_POST_UART)
 
-#define CFG_POST_CACHE_ADDR	0x10000000	/* free virtual address		*/
+#define CFG_POST_CACHE_ADDR	0x7fff0000 /* free virtual address	*/
 #define CONFIG_LOGBUFFER
 #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
 
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 48a64e3..1f72b54 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -377,7 +377,7 @@
 
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CONFIG_LOGBUFFER
-#define CFG_POST_CACHE_ADDR	0x10000000 /* free virtual address	*/
+#define CFG_POST_CACHE_ADDR	0x7fff0000 /* free virtual address	*/
 
 #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
 
-- 
cgit v1.1


From 87dc096829e6a6363f4fdd73653b0093a85adbe0 Mon Sep 17 00:00:00 2001
From: Larry Johnson <lrj@arlinx.com>
Date: Sat, 22 Dec 2007 15:16:25 -0500
Subject: Add configuration file for Korat board

This patch supplies the configuration file for the Korat PPC440EPx-
processor board.

Signed-off-by: Larry Johnson <lrj@acm.org>
---
 include/configs/korat.h | 376 ++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 376 insertions(+)
 create mode 100644 include/configs/korat.h

(limited to 'include/configs')

diff --git a/include/configs/korat.h b/include/configs/korat.h
new file mode 100644
index 0000000..1ea7d48
--- /dev/null
+++ b/include/configs/korat.h
@@ -0,0 +1,376 @@
+/*
+ * (C) Copyright 2007
+ * Larry Johnson, lrj@acm.org
+ *
+ * (C) Copyright 2006-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Alain Saurel,            AMCC/IBM, alain.saurel@fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * korat.h - configuration for Korat board
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_440EPX		1	/* Specific PPC440EPx           */
+#define CONFIG_4xx		1	/* ... PPC4xx family            */
+#define CONFIG_SYS_CLK_FREQ	33333333
+
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f      */
+#define CONFIG_MISC_INIT_R	1	/* Call misc_init_r             */
+
+/*-----------------------------------------------------------------------
+ * Manufacturer's information serial EEPROM parameters
+ *----------------------------------------------------------------------*/
+#define MAN_DATA_EEPROM_ADDR	0x53	/* EEPROM I2C address           */
+#define MAN_SERIAL_NO_FIELD	2
+#define MAN_SERIAL_NO_LENGTH	13
+#define MAN_MAC_ADDR_FIELD	3
+#define MAN_MAC_ADDR_LENGTH	17
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor   */
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()  */
+
+#define CFG_BOOT_BASE_ADDR	0xf0000000
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0          */
+#define CFG_FLASH_BASE		0xfc000000	/* start of FLASH       */
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_OCM_BASE		0xe0010000	/* ocm                  */
+#define CFG_OCM_DATA_ADDR	CFG_OCM_BASE
+#define CFG_PCI_BASE		0xe0000000	/* Internal PCI regs    */
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory    */
+#define CFG_PCI_MEMBASE1	CFG_PCI_MEMBASE  + 0x10000000
+#define CFG_PCI_MEMBASE2	CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3	CFG_PCI_MEMBASE2 + 0x10000000
+
+/* Don't change either of these */
+#define CFG_PERIPHERAL_BASE	0xef600000	/* internal peripherals */
+
+#define CFG_USB2D0_BASE		0xe0000100
+#define CFG_USB_DEVICE		0xe0000000
+#define CFG_USB_HOST		0xe0000400
+#define CFG_CPLD_BASE		0xc0000000
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+/* 440EPx has 16KB of internal SRAM, so no need for D-Cache		*/
+#undef CFG_INIT_RAM_DCACHE
+#define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM                  */
+#define CFG_INIT_RAM_END	(4 << 10)
+#define CFG_GBL_DATA_SIZE	256	/* num bytes initial data       */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CFG_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk   */
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI	1
+/* define this if you want console on UART1 */
+#undef CONFIG_UART1_CONSOLE
+
+#define CFG_BAUDRATE_TABLE						\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environ vars   */
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI			/* The flash is CFI compatible  */
+#define CFG_FLASH_CFI_DRIVER		/* Use common CFI driver        */
+
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip    */
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)      */
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)      */
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)     */
+#define CFG_FLASH_PROTECTION	1	/* use hardware flash protection        */
+
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash        */
+
+#define CFG_ENV_SECT_SIZE	0x20000	/* size of one complete sector          */
+#define CFG_ENV_ADDR		((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector     */
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM        (512)	/* 512 MiB      TODO: remove    */
+#define CONFIG_DDR_DATA_EYE		/* use DDR2 optimization        */
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for setup     */
+#define CONFIG_ZERO_SDRAM		/* Zero SDRAM after setup       */
+#define CONFIG_DDR_ECC			/* Use ECC when available       */
+#define SPD_EEPROM_ADDRESS	{0x50}
+#define CONFIG_PROG_SDRAM_TLB
+#define CFG_DRAM_TEST
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support    */
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged               */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address  */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T60	1
+#define CFG_I2C_RTC_ADDR	0x68
+
+/* I2C SYSMON (LM73)							*/
+#define CONFIG_DTT_LM73		1	/* National Semi's LM73 */
+#define CONFIG_DTT_SENSORS	{2}	/* Sensor addresses     */
+#define CFG_DTT_MAX_TEMP	70
+#define CFG_DTT_MIN_TEMP	-30
+
+#define CONFIG_PREBOOT	"echo;"						\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+/* Setup some board specific values for the default environment variables */
+#define CONFIG_HOSTNAME		korat
+#define CFG_BOOTFILE		"bootfile=/tftpboot/korat/uImage\0"
+#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xxFP\0"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CFG_BOOTFILE							\
+	CFG_ROOTPATH							\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
+	        "bootm\0"						\
+	"kernel_addr=FC000000\0"					\
+	"ramdisk_addr=FC180000\0"					\
+	"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0"		\
+	"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;"	\
+		"cp.b 200000 FFFA0000 60000\0"			        \
+	"upd=run load;run update\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds     */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download  */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change        */
+
+#define	CONFIG_IBM_EMAC4_V4	1
+#define CONFIG_MII		1	/* MII PHY management           */
+#define CONFIG_PHY_ADDR		2	/* PHY address, See schematics  */
+#define CONFIG_PHY_DYNAMIC_ANEG	1
+
+#define CONFIG_PHY_RESET        1	/* reset phy upon startup         */
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NET_MULTI	1
+#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
+#define CONFIG_PHY1_ADDR	3
+
+/* USB */
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_STORAGE
+
+/* Comment this out to enable USB 1.1 device */
+#define USB_2_0_DEVICE
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_SUBNETMASK
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_USB
+
+/* POST support */
+#define CONFIG_POST		(CFG_POST_CACHE    | \
+				 CFG_POST_CPU	   | \
+				 CFG_POST_ECC      | \
+				 CFG_POST_ETHER	   | \
+				 CFG_POST_FPU	   | \
+				 CFG_POST_I2C	   | \
+				 CFG_POST_MEMORY   | \
+				 CFG_POST_RTC      | \
+				 CFG_POST_SPR      | \
+				 CFG_POST_UART)
+
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_LOGBUFFER
+#define CFG_POST_CACHE_ADDR	0xC8000000	/* free virtual address      */
+
+#define CFG_CONSOLE_IS_IN_ENV	/* Otherwise it catches logbuffer as output */
+
+#define CONFIG_SUPPORT_VFAT
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory         */
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt       */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size      */
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size      */
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args   */
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on           */
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM        */
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address       */
+#define CFG_EXTBDINFO		1  /* To use extended board_into (bd_t) */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history     */
+#define CONFIG_LOOPW            1	/* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1	/* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+/* General PCI */
+#define CONFIG_PCI			/* include pci support          */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
+#define CFG_PCI_CACHE_LINE_SIZE	0	/* to avoid problems with PNP   */
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup  */
+#define CFG_PCI_TARGBASE        0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CFG_PCI_TARGET_INIT
+#define CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC                         */
+#define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever                     */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+
+/* Memory Bank 0 (NOR-FLASH) initialization				*/
+#define CFG_EBC_PB0AP		0x04017300
+#define CFG_EBC_PB0CR		(CFG_FLASH_BASE | 0x000DA000)
+
+/* Memory Bank 1 (NOR-FLASH) initialization				*/
+#define CFG_EBC_PB1AP		0x04017300
+#define CFG_EBC_PB1CR		(0xF8000000 | 0x000DA000)
+
+/* Memory Bank 2 (CPLD) initialization					*/
+#define CFG_EBC_PB2AP		0x04017300
+#define CFG_EBC_PB2CR		(CFG_CPLD_BASE | 0x00038000)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH     */
+#define BOOTFLAG_WARM	0x02	/* Software reboot                      */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use     */
+#endif
+#endif /* __CONFIG_H */
-- 
cgit v1.1


From b568fd25574181a3b12ae3d66b2913903442cb83 Mon Sep 17 00:00:00 2001
From: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Thu, 27 Dec 2007 17:03:46 +0100
Subject: Remove CPCI440 board

This board never left prototyping state and it
became a millstone round my neck. So remove it.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
---
 include/configs/CPCI440.h | 287 ----------------------------------------------
 1 file changed, 287 deletions(-)
 delete mode 100644 include/configs/CPCI440.h

(limited to 'include/configs')

diff --git a/include/configs/CPCI440.h b/include/configs/CPCI440.h
deleted file mode 100644
index eb47cd7..0000000
--- a/include/configs/CPCI440.h
+++ /dev/null
@@ -1,287 +0,0 @@
-/*
- * (C) Copyright 2002
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************************************
- * board/config_CPCI440.h - configuration for esd CPCI-440 board
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_CPCI440		1	    /* Board is ebony		*/
-#define CONFIG_440GP		1	    /* Specifc GP support	*/
-#define CONFIG_440		1	    /* ... PPC440 family	*/
-#define CONFIG_4xx		1	    /* ... PPC4xx family	*/
-#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
-#undef	CFG_DRAM_TEST			    /* Disable-takes long time! */
-#define CONFIG_SYS_CLK_FREQ	33330000 /* external frequency to pll	*/
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE	    0x00000000	    /* _must_ be 0		*/
-#define CFG_FLASH_BASE	    0xff800000	    /* start of FLASH		*/
-#if 1
-#define CFG_MONITOR_BASE    0xfffc0000	    /* start of monitor		*/
-#else
-#define CFG_MONITOR_BASE    0x01fc0000	    /* start of monitor		*/
-#endif
-#define CFG_PERIPHERAL_BASE 0xe0000000	    /* internal peripherals	*/
-#define CFG_ISRAM_BASE	    0xc0000000	    /* internal SRAM		*/
-
-#define CFG_FPGA_BASE	    (CFG_PERIPHERAL_BASE + 0x08300000)
-#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR   CFG_ISRAM_BASE  /* Initial RAM address	*/
-#define CFG_INIT_RAM_END    0x2000	    /* End of used area in RAM	*/
-#define CFG_GBL_DATA_SIZE  128		    /* num bytes initial data	*/
-
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN	    (192 * 1024)    /* Reserve 192 kB for Mon	*/
-#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#undef CFG_EXT_SERIAL_CLOCK /*	 (1843200 * 6)	 / * Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE		9600
-
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
-
-/*-----------------------------------------------------------------------
- * NVRAM/RTC
- *
- * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
- * The DS1743 code assumes this condition (i.e. -- it assumes the base
- * address for the RTC registers is:
- *
- *	CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
- *
- *----------------------------------------------------------------------*/
-#define CFG_NVRAM_SIZE	    (0x2000 - 8)    /* NVRAM size(8k)- RTC regs */
-#define CONFIG_RTC_DS174x	1		    /* DS1743 RTC		*/
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#if 1 /* test-only */
-
-#define CFG_FLASH_CFI		1	/* Flash is CFI conformant		*/
-#define CFG_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_FLASH_INCREMENT	0	/* there is only one bank		*/
-#define CFG_FLASH_PROTECTION	1	/* use hardware protection		*/
-#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-#undef CFG_FLASH_BASE
-#define CFG_FLASH_BASE		0xFF800000 /* test-only...*/
-
-#else /* test-only */
-
-#define CFG_MAX_FLASH_BANKS	3		    /* number of banks	    */
-#define CFG_MAX_FLASH_SECT	32		    /* sectors per device   */
-
-#undef	CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#endif
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-#if 0 /* test-only */
-#define CFG_ENV_IS_IN_NVRAM	1	    /* Environment uses NVRAM	*/
-#undef	CFG_ENV_IS_IN_FLASH		    /* ... not in flash		*/
-#undef	CFG_ENV_IS_IN_EEPROM		    /* ... not in EEPROM	*/
-
-#define CFG_ENV_SIZE		0x1000	    /* Size of Environment vars */
-#define CFG_ENV_ADDR		\
-	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)
-#else
-
-#if 0 /* test-only */
-#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET		0x010	/* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars*/
-				   /* total size of a CAT24WC16 is 2048 bytes */
-#else
-#define CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
-#define CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CFG_I2C_SLAVE		0x7F
-
-#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last 4 bits of the address	*/
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-
-#endif
-
-#undef	CONFIG_BOOTARGS
-#undef	CONFIG_BOOTCOMMAND
-
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
-#define CONFIG_BAUDRATE		9600
-
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		1	/* PHY address			*/
-#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#undef CONFIG_SPD_EEPROM       /* don't use SPD EEPROM for setup    */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
-
-#if 0 /* test-only */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
-#endif
-
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#if 0
-#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
-#define PCI_HOST_FORCE	1		/* configure as pci host	*/
-#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
-
-#define CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_HOST PCI_HOST_FORCE	/* select pci host function	*/
-#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-					/* resource configuration	*/
-
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x0000	/* PCI Vendor ID: to-do!!!	*/
-#define CFG_PCI_SUBSYS_DEVICEID 0x0000	/* PCI Device ID: to-do!!!	*/
-#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
-#define CFG_PCI_PTM1MS	0x80000001	/* 2GB, enable hard-wired to 1	*/
-#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
-#define CFG_PCI_PTM2LA	0x00000000	/* disabled			*/
-#define CFG_PCI_PTM2MS	0x00000000	/* disabled			*/
-#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR	0xF0000500
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS	0x50
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-#endif	/* __CONFIG_H */
-- 
cgit v1.1


From b56bd0fcfc1c73db722e3462c8a9bf607ba7775e Mon Sep 17 00:00:00 2001
From: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Fri, 28 Dec 2007 17:10:42 +0100
Subject: ppc4xx: Maintenance patch for VOH405 boards

- add EEPROM write protection
- initialize NAND GPIOs
- use correct io accessors
- slow down I2C clock to 100kHz
- enable ext. I2C bus
- cleanup

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
---
 include/configs/VOH405.h | 31 +++++++++++--------------------
 1 file changed, 11 insertions(+), 20 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h
index 3a413f5..3ca928e 100644
--- a/include/configs/VOH405.h
+++ b/include/configs/VOH405.h
@@ -52,9 +52,13 @@
 
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_NET_MULTI	1
+#undef  CONFIG_HAS_ETH1
+
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -204,8 +208,6 @@
 #define CFG_IDE_MAXBUS		2		/* max. 2 IDE busses	*/
 #define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
 
-#define CONFIG_ATAPI		1	/* ATAPI for Travelstar		*/
-
 #define CFG_ATA_BASE_ADDR	0xF0100000
 #define CFG_ATA_IDE0_OFFSET	0x0000
 #define CFG_ATA_IDE1_OFFSET	0x0010
@@ -244,11 +246,6 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
-#endif
-
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
@@ -281,19 +278,12 @@
  * I2C EEPROM (CAT24WC16) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SPEED		100000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
-#if 0 /* test-only */
-/* CAT24WC08/16... */
-#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last 4 bits of the address	*/
-#else
+#define CFG_EEPROM_WREN         1
+
 /* CAT24WC32/64... */
 #define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
@@ -301,7 +291,6 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
 					/* 32 byte page write mode using*/
 					/* last 5 bits of the address	*/
-#endif
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
@@ -400,18 +389,20 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs -> GPIO
  */
-#define CFG_GPIO0_OSRH		0x40000550
+#define CFG_GPIO0_OSRH		0x00000550
 #define CFG_GPIO0_OSRL		0x00000110
 #define CFG_GPIO0_ISR1H		0x00000000
 #define CFG_GPIO0_ISR1L		0x15555440
 #define CFG_GPIO0_TSRH		0x00000000
 #define CFG_GPIO0_TSRL		0x00000000
-#define CFG_GPIO0_TCR		0xF7FE0017
+#define CFG_GPIO0_TCR		0x777E0017
 
 #define CFG_DUART_RST		(0x80000000 >> 14)
 #define CFG_LCD_ENDIAN		(0x80000000 >> 7)
+#define CFG_IIC_ON		(0x80000000 >> 8)
 #define CFG_LCD0_RST		(0x80000000 >> 30)
 #define CFG_LCD1_RST		(0x80000000 >> 31)
+#define CFG_EEPROM_WP		(0x80000000 >> 0)
 
 /*
  * Internal Definitions
-- 
cgit v1.1


From f6e0f1f61896ce7729ba1bcea2ffbd138d3947f5 Mon Sep 17 00:00:00 2001
From: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Fri, 28 Dec 2007 17:10:36 +0100
Subject: ppc4xx: Add EEPROM write protection for PLU405 boards + misc. updates

- add EEPROM write protection for esd PLU405 boards.
- initialize NAND GPIOs
- use correct io accessors
- cleanup

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
---
 include/configs/PLU405.h | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 6b16654..0bd77c0 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -288,6 +288,7 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
+#define CFG_EEPROM_WREN         1
 
 /* CAT24WC08/16... */
 #define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
@@ -379,15 +380,16 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CFG_GPIO0_OSRH		0x40000550
+#define CFG_GPIO0_OSRH		0x00000550
 #define CFG_GPIO0_OSRL		0x00000110
 #define CFG_GPIO0_ISR1H		0x00000000
 #define CFG_GPIO0_ISR1L		0x15555445
 #define CFG_GPIO0_TSRH		0x00000000
 #define CFG_GPIO0_TSRL		0x00000000
-#define CFG_GPIO0_TCR		0xF7FE0014
+#define CFG_GPIO0_TCR		0x77FE0014
 
 #define CFG_DUART_RST		(0x80000000 >> 14)
+#define CFG_EEPROM_WP		(0x80000000 >> 0)
 
 /*
  * Internal Definitions
-- 
cgit v1.1


From 8ba132cab18ae438b6dd5b0214c28a8fc0d976e5 Mon Sep 17 00:00:00 2001
From: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Fri, 28 Dec 2007 17:07:24 +0100
Subject: ppc4xx: Complete PMC440 board support

This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
---
 include/configs/PMC440.h | 522 +++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 522 insertions(+)
 create mode 100644 include/configs/PMC440.h

(limited to 'include/configs')

diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h
new file mode 100644
index 0000000..3d2ed1e
--- /dev/null
+++ b/include/configs/PMC440.h
@@ -0,0 +1,522 @@
+/*
+ * (C) Copyright 2007
+ * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com.
+ * Based on the sequoia configuration file.
+ *
+ * (C) Copyright 2006-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Alain Saurel,            AMCC/IBM, alain.saurel@fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * PMC440.h - configuration for esd PMC440 boards
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_440EPX		1	/* Specific PPC440EPx   */
+#define CONFIG_440		1	/* ... PPC440 family    */
+#define CONFIG_4xx		1	/* ... PPC4xx family    */
+
+#define CONFIG_SYS_CLK_FREQ	33333400
+
+#define CONFIG_4xx_DCACHE		/* enable dcache        */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R	1	/* Call misc_init_r     */
+#define CONFIG_BOARD_TYPES	1	/* support board types  */
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(384  * 1024)	/* Reserve 384 kB for Monitor   */
+#define CFG_MALLOC_LEN		(1024 * 1024)	/* Reserve 256 kB for malloc()  */
+
+#define CONFIG_PRAM		0	/* use pram variable to overwrite */
+
+#define CFG_BOOT_BASE_ADDR	0xf0000000
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0          */
+#define CFG_FLASH_BASE		0xfc000000	/* start of FLASH       */
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_NAND_ADDR		0xd0000000	/* NAND Flash           */
+#define CFG_OCM_BASE		0xe0010000	/* ocm                  */
+#define CFG_OCM_DATA_ADDR	CFG_OCM_BASE
+#define CFG_PCI_BASE		0xe0000000	/* Internal PCI regs    */
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory    */
+#define CFG_PCI_MEMBASE1	CFG_PCI_MEMBASE  + 0x10000000
+#define CFG_PCI_MEMBASE2	CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3	CFG_PCI_MEMBASE2 + 0x10000000
+#define CFG_PCI_MEMSIZE		0x80000000	/* 2GB! */
+
+/* Don't change either of these */
+#define CFG_PERIPHERAL_BASE	0xef600000	/* internal peripherals */
+
+#define CFG_USB2D0_BASE		0xe0000100
+#define CFG_USB_DEVICE		0xe0000000
+#define CFG_USB_HOST		0xe0000400
+#define CFG_FPGA_BASE0		0xef000000	/* 32 bit */
+#define CFG_FPGA_BASE1		0xef100000	/* 16 bit */
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache	*/
+#define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM                  */
+#define CFG_INIT_RAM_END	(4 << 10)
+#define CFG_GBL_DATA_SIZE	256	/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CFG_EXT_SERIAL_CLOCK
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI	1
+#undef CONFIG_UART1_CONSOLE	/* console on front panel */
+
+#define CFG_BAUDRATE_TABLE						\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_ENV_IS_IN_EEPROM	1	/* use FLASH for environment vars */
+#else
+#define CFG_ENV_IS_IN_NAND	1	/* use NAND for environment vars */
+#define CFG_ENV_IS_EMBEDDED	1	/* use embedded environment */
+#endif
+
+/*-----------------------------------------------------------------------
+ * RTC
+ *----------------------------------------------------------------------*/
+#define CONFIG_RTC_RX8025
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI		/* The flash is CFI compatible  */
+#define CFG_FLASH_CFI_DRIVER	/* Use common CFI driver        */
+
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip    */
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)      */
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)      */
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)     */
+#define CFG_FLASH_PROTECTION	1	/* use hardware flash protection        */
+
+#define CFG_FLASH_EMPTY_INFO	/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash        */
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x20000	/* size of one complete sector          */
+#define CFG_ENV_ADDR		((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector     */
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif
+
+#ifdef CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_OFFSET		0	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x1000	/* 4096 bytes may be used for env vars */
+#endif
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller.	sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location                 */
+#define CFG_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size                     */
+#define CFG_NAND_BOOT_SPL_DST	(CFG_OCM_BASE + (12 << 10)) /* Copy SPL here    */
+#define CFG_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr        */
+#define CFG_NAND_U_BOOT_START	CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CFG_NAND_BOOT_SPL_DELTA	(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image   */
+#define CFG_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image     */
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE	512	/* NAND chip page size          */
+#define CFG_NAND_BLOCK_SIZE	(16 << 10) /* NAND chip block size      */
+#define CFG_NAND_PAGE_COUNT	32	/* NAND chip page count         */
+#define CFG_NAND_BAD_BLOCK_POS	5	/* Location of bad block marker */
+#undef CFG_NAND_4_ADDR_CYCLE		/* No fourth addr used (<=32MB) */
+
+#define CFG_NAND_ECCSIZE	256
+#define CFG_NAND_ECCBYTES	3
+#define CFG_NAND_ECCSTEPS	(CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE	16
+#define CFG_NAND_ECCTOTAL	(CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE		CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET		(CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM	(256)	/* 256MB                        */
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_DDR_DATA_EYE	/* use DDR2 optimization        */
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support    */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged               */
+#define CFG_I2C_SPEED		100000	/* I2C speed and slave address  */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CONFIG_I2C_CMD_TREE	1
+#define CONFIG_I2C_MULTI_BUS	1
+
+#define CFG_I2C_MULTI_EEPROMS
+
+#define CFG_I2C_EEPROM_ADDR		0x54
+#define CFG_I2C_EEPROM_ADDR_LEN		2
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS	5
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
+
+#define CFG_EEPROM_WREN			1
+#define CFG_I2C_BOOT_EEPROM_ADDR	0x52
+
+/*
+ * standard dtt sensor configuration - bottom bit will determine local or
+ * remote sensor of the TMP401
+ */
+#define CONFIG_DTT_SENSORS		{ 0, 1 }
+
+/*
+ * The PMC440 uses a TI TMP401 temperature sensor. This part
+ * is basically compatible to the ADM1021 that is supported
+ * by U-Boot.
+ *
+ * - i2c addr 0x4c
+ * - conversion rate 0x02 = 0.25 conversions/second
+ * - ALERT ouput disabled
+ * - local temp sensor enabled, min set to 0 deg, max set to 70 deg
+ * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
+ */
+#define CONFIG_DTT_ADM1021
+#define CFG_DTT_ADM1021		{ { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
+
+#define CONFIG_PREBOOT		/* enable preboot variable */
+
+#undef	CONFIG_BOOTARGS
+
+/* Setup some board specific values for the default environment variables */
+#define CONFIG_HOSTNAME		pmc440
+#define CFG_BOOTFILE		"bootfile=/tftpboot/pmc440/uImage\0"
+#define CFG_ROOTPATH		"rootpath=/opt/eldk_410/ppc_4xx\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	CFG_BOOTFILE							\
+	CFG_ROOTPATH							\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+	"nfsroot=${serverip}:${rootpath}\0"				\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"		\
+	":${hostname}:${netdev}:off panic=1\0"				\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
+	"flash_nfs=run nfsargs addip addtty;"				\
+	"bootm ${kernel_addr}\0"					\
+	"flash_self=run ramargs addip addtty;"				\
+	"bootm ${kernel_addr} ${ramdisk_addr}\0"			\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
+	"bootm\0"							\
+	"kernel_addr=FC000000\0"					\
+	"ramdisk_addr=FC180000\0"					\
+	"load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0"		\
+	"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;"	\
+	"cp.b 200000 FFFA0000 60000\0"					\
+	""
+
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds     */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download  */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change        */
+
+#define CONFIG_IBM_EMAC4_V4	1
+#define CONFIG_MII		1	/* MII PHY management           */
+#define CONFIG_PHY_ADDR		0	/* PHY address, See schematics  */
+
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NET_MULTI	1
+#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
+#define CONFIG_PHY1_ADDR	1
+#define CONFIG_RESET_PHY_R	1
+
+/* USB */
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_STORAGE
+#define CFG_OHCI_BE_CONTROLLER
+
+#define CFG_USB_OHCI_BOARD_INIT 1
+#define CFG_USB_OHCI_CPU_INIT	1
+#define CFG_USB_OHCI_REGS_BASE	CFG_USB_HOST
+#define CFG_USB_OHCI_SLOT_NAME	"ppc440"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS	15
+
+/* Comment this out to enable USB 1.1 device */
+#define USB_2_0_DEVICE
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+
+/* POST support */
+/* ethernet POST sometimes freezes the CPU.
+ * So disable it for now until issue is solved
+ */
+#if 0
+#define CONFIG_POST		(CFG_POST_MEMORY |	\
+				 CFG_POST_CPU    |	\
+				 CFG_POST_UART   |	\
+				 CFG_POST_I2C    |	\
+				 CFG_POST_CACHE  |	\
+				 CFG_POST_FPU    |	\
+				 CFG_POST_ETHER  |	\
+				 CFG_POST_SPR)
+#else
+#define CONFIG_POST		(CFG_POST_MEMORY |	\
+				 CFG_POST_CPU    |	\
+				 CFG_POST_UART   |	\
+				 CFG_POST_I2C    |	\
+				 CFG_POST_CACHE  |	\
+				 CFG_POST_FPU    |	\
+				 CFG_POST_SPR)
+#endif
+
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+
+/* esd expects pram at end of physical memory.
+ * So no logbuffer at the moment.
+ */
+#if 0
+#define CONFIG_LOGBUFFER
+#endif
+#define CFG_POST_CACHE_ADDR	0x10000000	/* free virtual address     */
+
+#define CFG_CONSOLE_IS_IN_ENV	/* Otherwise it catches logbuffer as output */
+
+#define CONFIG_SUPPORT_VFAT
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory         */
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt       */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
+#else
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
+#endif
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on          */
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM       */
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address      */
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history     */
+#define CONFIG_LOOPW		1	/* enable loopw command         */
+#define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+#define CONFIG_AUTOBOOT_KEYED	1
+#define CONFIG_AUTOBOOT_PROMPT	"Press SPACE to abort autoboot in %d seconds\n"
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+/* General PCI */
+#define CONFIG_PCI		/* include pci support          */
+#define CONFIG_PCI_PNP		/* do (not) pci plug-and-play   */
+#define CFG_PCI_CACHE_LINE_SIZE	0	/* to avoid problems with PNP   */
+#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup  */
+#define CFG_PCI_TARGBASE	0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CFG_PCI_TARGET_INIT
+#define CFG_PCI_MASTER_INIT
+
+/* PCI identification */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh      */
+#define CFG_PCI_SUBSYS_ID_NONMONARCH 0x0441	/* PCI Device ID: Non-Monarch */
+#define CFG_PCI_SUBSYS_ID_MONARCH 0x0440	/* PCI Device ID: Monarch */
+#define CFG_PCI_CLASSCODE_NONMONARCH	PCI_CLASS_PROCESSOR_POWERPC
+#define CFG_PCI_CLASSCODE_MONARCH	PCI_CLASS_BRIDGE_HOST
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ *----------------------------------------------------------------------*/
+#define CONFIG_FPGA
+#define CONFIG_FPGA_XILINX
+#define CONFIG_FPGA_SPARTAN2
+#define CONFIG_FPGA_SPARTAN3
+
+#define CONFIG_FPGA_COUNT	2
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+
+/*
+ * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
+ */
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_NAND_CS		2	/* NAND chip connected to CSx   */
+
+/* Memory Bank 0 (NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP		0x03017200
+#define CFG_EBC_PB0CR		(CFG_FLASH_BASE | 0xda000)
+
+/* Memory Bank 2 (NAND-FLASH) initialization */
+#define CFG_EBC_PB2AP		0x018003c0
+#define CFG_EBC_PB2CR		(CFG_NAND_ADDR | 0x1c000)
+#else
+#define CFG_NAND_CS		0	/* NAND chip connected to CSx   */
+/* Memory Bank 2 (NOR-FLASH) initialization */
+#define CFG_EBC_PB2AP		0x03017200
+#define CFG_EBC_PB2CR		(CFG_FLASH_BASE | 0xda000)
+
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CFG_EBC_PB0AP		0x018003c0
+#define CFG_EBC_PB0CR		(CFG_NAND_ADDR | 0x1c000)
+#endif
+
+/* Memory Bank 4 (FPGA / 32Bit) initialization */
+#define CFG_EBC_PB4AP		0x03840f40	/* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */
+#define CFG_EBC_PB4CR		(CFG_FPGA_BASE0 | 0x1c000)	/* BS=1M,BU=R/W,BW=32bit */
+
+/* Memory Bank 5 (FPGA / 16Bit) initialization */
+#define CFG_EBC_PB5AP		0x03840f40	/* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */
+#define CFG_EBC_PB5CR		(CFG_FPGA_BASE1 | 0x1a000)	/* BS=1M,BU=R/W,BW=16bit */
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS		1
+#define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE	1 /* nand driver supports mutipl. chips */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH     */
+#define BOOTFLAG_WARM	0x02	/* Software reboot                      */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+#endif /* __CONFIG_H */
-- 
cgit v1.1


From ea9f7395ec362584e5e4f266bd0b0c4422cf6a4c Mon Sep 17 00:00:00 2001
From: Jon Loeliger <jdl@freescale.com>
Date: Wed, 28 Nov 2007 14:47:18 -0600
Subject: Convert MPC8641HPCN to use libfdt.

Assumes the presence of the aliases node in the DTS to
locate the ethernet, pci and serial nodes for fixups.

Use consistent fdtaddr and fdtfile in environment variables.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8641HPCN.h | 21 +++++++++------------
 1 file changed, 9 insertions(+), 12 deletions(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 6f87240..0fc6521 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -267,13 +267,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Pass open firmware flat tree to kernel
  */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
-#define OF_CPU		"PowerPC,8641@0"
-#define OF_SOC		"soc8641@f8000000"
-#define OF_TBCLK	(bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH	"/soc8641@f8000000/serial@4500"
 
 #define CFG_64BIT_VSPRINTF	1
 #define CFG_64BIT_STRTOUL	1
@@ -645,8 +642,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
    "consoledev=ttyS0\0"                                                 \
    "ramdiskaddr=2000000\0"						\
    "ramdiskfile=your.ramdisk.u-boot\0"                                  \
-   "dtbaddr=c00000\0"						\
-   "dtbfile=mpc8641_hpcn.dtb\0"                                  \
+   "fdtaddr=c00000\0"						\
+   "fdtfile=mpc8641_hpcn.dtb\0"                                  \
    "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
    "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
    "maxcpus=2"
@@ -658,16 +655,16 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
       "console=$consoledev,$baudrate $othbootargs;"                     \
    "tftp $loadaddr $bootfile;"                                          \
-   "tftp $dtbaddr $dtbfile;"                                          \
-   "bootm $loadaddr - $dtbaddr"
+   "tftp $fdtaddr $fdtfile;"                                          \
+   "bootm $loadaddr - $fdtaddr"
 
 #define CONFIG_RAMBOOTCOMMAND \
    "setenv bootargs root=/dev/ram rw "                                  \
       "console=$consoledev,$baudrate $othbootargs;"                     \
    "tftp $ramdiskaddr $ramdiskfile;"                                    \
    "tftp $loadaddr $bootfile;"                                          \
-   "tftp $dtbaddr $dtbfile;"                                          \
-   "bootm $loadaddr $ramdiskaddr $dtbaddr"
+   "tftp $fdtaddr $fdtfile;"                                          \
+   "bootm $loadaddr $ramdiskaddr $fdtaddr"
 
 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 
-- 
cgit v1.1


From 61d3421bdea090bd0399b14c3e10a3bebcc8d5ff Mon Sep 17 00:00:00 2001
From: Jon Loeliger <jdl@freescale.com>
Date: Tue, 4 Dec 2007 10:53:34 -0600
Subject: Don't slam #undef DEBUG in the 8641HPCN config file.

Doing so prevents it from being individually set
and useful in other files.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
 include/configs/MPC8641HPCN.h | 1 -
 1 file changed, 1 deletion(-)

(limited to 'include/configs')

diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 0fc6521..575bbae 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -38,7 +38,6 @@
 #define CONFIG_MPC8641HPCN	1	/* MPC8641HPCN board specific */
 #define CONFIG_NUM_CPUS         2       /* Number of CPUs in the system */
 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
-#undef DEBUG
 
 #ifdef RUN_DIAG
 #define CFG_DIAG_ADDR        0xff800000
-- 
cgit v1.1