From 649acfe149e8a534a17eab54004a51d69b5556ed Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Mon, 11 Nov 2013 20:12:19 +0100 Subject: MPC824x: remove obsolete "PN62" board The MPC824x processors have long reached EOL, and the PN62 board has not seen any board-specific updates for more than a decade. It is now causing build issues. Instead of wasting time on things nobody is interested in any more, we rather drop this board. Signed-off-by: Wolfgang Denk Cc: Wolfgang Grandegger cc: Tom Rini --- include/configs/PN62.h | 285 ------------------------------------------------- 1 file changed, 285 deletions(-) delete mode 100644 include/configs/PN62.h (limited to 'include/configs/PN62.h') diff --git a/include/configs/PN62.h b/include/configs/PN62.h deleted file mode 100644 index 2a82f94..0000000 --- a/include/configs/PN62.h +++ /dev/null @@ -1,285 +0,0 @@ -/* - * (C) Copyright 2002 - * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC824X 1 -#define CONFIG_MPC8240 1 -#define CONFIG_PN62 1 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_CONS_INDEX 1 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_BSP - -#undef CONFIG_CMD_FLASH -#undef CONFIG_CMD_IMLS -#undef CONFIG_CMD_LOADS -#undef CONFIG_CMD_SAVEENV -#undef CONFIG_CMD_SOURCE - - -#define CONFIG_BAUDRATE 19200 /* console baudrate */ - -#define CONFIG_BOOTDELAY 1 /* autoboot after n seconds */ - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#define CONFIG_SERVERIP 10.0.0.201 -#define CONFIG_IPADDR 10.0.0.200 -#define CONFIG_ROOTPATH "/opt/eldk/ppc_82xx" -#define CONFIG_NETMASK 255.255.255.0 -#undef CONFIG_BOOTARGS -#if 0 -/* Boot Linux with NFS root filesystem */ -#define CONFIG_BOOTCOMMAND \ - "setenv verify y;" \ - "setenv bootargs console=ttyS0,19200 mem=31M quiet " \ - "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \ - "loadp 100000; bootm" - /* "tftpboot 100000 uImage; bootm" */ -#else -/* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */ -#define CONFIG_BOOTCOMMAND \ - "setenv verify n;" \ - "setenv bootargs console=ttyS0,19200 mem=31M quiet " \ - "root=/dev/ram rw " \ - "ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \ - "loadp 200000; bootm" -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -#define CONFIG_PRAM 1024 /* reserve 1 MB protected RAM */ - -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */ - -#define CONFIG_HAS_ETH1 1 /* add support for eth1addr */ - -#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ - -/* - * PCI stuff - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* we need Plug 'n Play */ -#if 0 -#define CONFIG_PCI_SCAN_SHOW /* show PCI auto-scan at boot */ -#endif - -/* - * Networking stuff - */ - -#define CONFIG_PCNET /* there are 2 AMD PCnet 79C973 */ -#define CONFIG_PCNET_79C973 - -#define _IO_BASE 0xfe000000 /* points to PCI I/O space */ - - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 - -#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 - -#undef CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_MONITOR_LEN 0x00030000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - - -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - - -#define CONFIG_SYS_NO_FLASH 1 /* There is no FLASH memory */ - -#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ -#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */ - -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ - -#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x01f00000 /* 0 ... 32 MB in DRAM */ - -/* - * Serial port configuration - */ - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL - -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_NS16550_CLK 1843200 - -#define CONFIG_SYS_NS16550_COM1 0xff800008 -#define CONFIG_SYS_NS16550_COM2 0xff800000 - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3 - -#define CONFIG_SYS_EUMB_ADDR 0xFCE00000 - -/* MCCR1 */ -#define CONFIG_SYS_ROMNAL 3 /* rom/flash next access time */ -#define CONFIG_SYS_ROMFAL 7 /* rom/flash access time */ - -/* MCCR2 */ -#define CONFIG_SYS_ASRISE 6 /* ASRISE in clocks */ -#define CONFIG_SYS_ASFALL 12 /* ASFALL in clocks */ -#define CONFIG_SYS_REFINT 5600 /* REFINT in clocks */ - -/* MCCR3 */ -#define CONFIG_SYS_BSTOPRE 0x3cf /* Burst To Precharge */ -#define CONFIG_SYS_REFREC 2 /* Refresh to activate interval */ -#define CONFIG_SYS_RDLAT 3 /* data latency from read command */ - -/* MCCR4 */ -#define CONFIG_SYS_PRETOACT 1 /* Precharge to activate interval */ -#define CONFIG_SYS_ACTTOPRE 3 /* Activate to Precharge interval */ -#define CONFIG_SYS_ACTORW 2 /* Activate to R/W */ -#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */ -#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE Wrap type */ -#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */ -#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 - -/* Memory bank settings: - * - * only bits 20-29 are actually used from these vales to set the - * start/qend address the upper two bits will be 0, and the lower 20 - * bits will be set to 0x00000 for a start address, or 0xfffff for an - * end address - */ -#define CONFIG_SYS_BANK0_START 0x00000000 -#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) -#define CONFIG_SYS_BANK0_ENABLE 1 -#define CONFIG_SYS_BANK1_START 0x00000000 -#define CONFIG_SYS_BANK1_END 0x00000000 -#define CONFIG_SYS_BANK1_ENABLE 0 -#define CONFIG_SYS_BANK2_START 0x00000000 -#define CONFIG_SYS_BANK2_END 0x00000000 -#define CONFIG_SYS_BANK2_ENABLE 0 -#define CONFIG_SYS_BANK3_START 0x00000000 -#define CONFIG_SYS_BANK3_END 0x00000000 -#define CONFIG_SYS_BANK3_ENABLE 0 -#define CONFIG_SYS_BANK4_START 0x00000000 -#define CONFIG_SYS_BANK4_END 0x00000000 -#define CONFIG_SYS_BANK4_ENABLE 0 -#define CONFIG_SYS_BANK5_START 0x00000000 -#define CONFIG_SYS_BANK5_END 0x00000000 -#define CONFIG_SYS_BANK5_ENABLE 0 -#define CONFIG_SYS_BANK6_START 0x00000000 -#define CONFIG_SYS_BANK6_END 0x00000000 -#define CONFIG_SYS_BANK6_ENABLE 0 -#define CONFIG_SYS_BANK7_START 0x00000000 -#define CONFIG_SYS_BANK7_END 0x00000000 -#define CONFIG_SYS_BANK7_ENABLE 0 - -/* - * Memory bank enable bitmask, specifying which of the banks defined above - * are actually present. MSB is for bank #7, LSB is for bank #0. - */ -#define CONFIG_SYS_BANK_ENABLE 0x01 - -#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */ - /* see 8240 book for bit definitions */ -#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */ - /* currently accessed page in memory */ - /* see 8240 book for details */ - -/* SDRAM 0 - 256MB */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) - -/* PCI memory space */ -#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -/* Config addrs, etc */ -#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#endif /* __CONFIG_H */ -- cgit v1.1