From 557b377d8bfc8b833b6e749457bcdfa298331a24 Mon Sep 17 00:00:00 2001 From: Jens Gehrlein Date: Mon, 5 May 2008 14:06:11 +0200 Subject: smc911x: add 16 bit support Signed-off-by: Jens Gehrlein Signed-off-by: Ben Warren --- drivers/net/smc911x.c | 21 +++++++++++++++++++-- 1 file changed, 19 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 5302cb5..6d93bf0 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -30,6 +30,12 @@ #include #include +#if defined (CONFIG_DRIVER_SMC911X_32_BIT) && \ + defined (CONFIG_DRIVER_SMC911X_16_BIT) +#error "SMC911X: Only one of CONFIG_DRIVER_SMC911X_32_BIT and \ + CONFIG_DRIVER_SMC911X_16_BIT shall be set" +#endif + #ifdef CONFIG_DRIVER_SMC911X_32_BIT static inline u32 reg_read(u32 addr) { @@ -39,9 +45,20 @@ static inline void reg_write(u32 addr, u32 val) { *(volatile u32*)addr = val; } +#elif CONFIG_DRIVER_SMC911X_16_BIT +static inline u32 reg_read(u32 addr) +{ + volatile u16 *addr_16 = (u16 *)addr; + return ((*addr_16 & 0x0000ffff) | (*(addr_16 + 1) << 16)); +} +static inline void reg_write(u32 addr, u32 val) +{ + *(volatile u16*)addr = (u16)val; + *(volatile u16*)(addr + 2) = (u16)(val >> 16); +} #else -#error "SMC911X: Only 32-bit bus is supported" -#endif +#error "SMC911X: undefined bus width" +#endif /* CONFIG_DRIVER_SMC911X_16_BIT */ #define mdelay(n) udelay((n)*1000) -- cgit v1.1 From 290ef6436838b1cc013bd67e0e0495c9eb3e23c0 Mon Sep 17 00:00:00 2001 From: Ron Madrid Date: Fri, 23 May 2008 15:37:05 -0700 Subject: Add Marvell 88E1118 support for TSEC Signed-off-by: Ron Madrid Signed-off-by: Ben Warren --- drivers/net/tsec.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) (limited to 'drivers') diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c index c7af930..397ae71 100644 --- a/drivers/net/tsec.c +++ b/drivers/net/tsec.c @@ -1128,6 +1128,36 @@ struct phy_info phy_info_M88E1111S = { }, }; +struct phy_info phy_info_M88E1118 = { + 0x01410e1, + "Marvell 88E1118", + 4, + (struct phy_cmd[]){ /* config */ + /* Reset and configure the PHY */ + {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL}, + {0x16, 0x0002, NULL}, /* Change Page Number */ + {0x15, 0x1070, NULL}, /* Delay RGMII TX and RX */ + {MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL}, + {MIIM_ANAR, MIIM_ANAR_INIT, NULL}, + {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL}, + {MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init}, + {miim_end,} + }, + (struct phy_cmd[]){ /* startup */ + {0x16, 0x0000, NULL}, /* Change Page Number */ + /* Status is read once to clear old link state */ + {MIIM_STATUS, miim_read, NULL}, + /* Auto-negotiate */ + /* Read the status */ + {MIIM_88E1011_PHY_STATUS, miim_read, + &mii_parse_88E1011_psr}, + {miim_end,} + }, + (struct phy_cmd[]){ /* shutdown */ + {miim_end,} + }, +}; + static unsigned int m88e1145_setmode(uint mii_reg, struct tsec_private *priv) { uint mii_data = read_phy_reg(priv, mii_reg); @@ -1492,6 +1522,7 @@ struct phy_info *phy_info[] = { &phy_info_BCM5464S, &phy_info_M88E1011S, &phy_info_M88E1111S, + &phy_info_M88E1118, &phy_info_M88E1145, &phy_info_M88E1149S, &phy_info_dm9161, -- cgit v1.1 From ff36fbb2e7583fb808eef773f511489c7a9c2df3 Mon Sep 17 00:00:00 2001 From: TsiChung Liew Date: Wed, 28 May 2008 13:06:25 -0500 Subject: ColdFire: Add 10 base ethernet support for mcf5445x Signed-off-by: TsiChung Liew Signed-off-by: Ben Warren --- drivers/net/mcffec.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/net/mcffec.c b/drivers/net/mcffec.c index 5ab4726..8d4e248 100644 --- a/drivers/net/mcffec.c +++ b/drivers/net/mcffec.c @@ -125,11 +125,17 @@ void setFecDuplexSpeed(volatile fec_t * fecp, bd_t * bd, int dup_spd) } if ((dup_spd & 0xFFFF) == _100BASET) { +#ifdef CONFIG_MCF5445x + fecp->rcr &= ~0x200; /* disabled 10T base */ +#endif #ifdef MII_DEBUG printf("100Mbps\n"); #endif bd->bi_ethspeed = 100; } else { +#ifdef CONFIG_MCF5445x + fecp->rcr |= 0x200; /* enabled 10T base */ +#endif #ifdef MII_DEBUG printf("10Mbps\n"); #endif -- cgit v1.1 From aa3b8bf9c30065bb2ea852799d32db5020598495 Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Wed, 28 May 2008 19:55:19 +0200 Subject: E1000: Add support for the 82541GI LF Intel Pro 1000 GT Desktop Adapter Signed-off-by: Wolfgang Grandegger Signed-off-by: Ben Warren --- drivers/net/e1000.c | 2 ++ drivers/net/e1000.h | 3 ++- 2 files changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c index c53c226..40a781f 100644 --- a/drivers/net/e1000.c +++ b/drivers/net/e1000.c @@ -83,6 +83,7 @@ static struct pci_device_id supported[] = { {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_FIBER}, {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM}, {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541ER}, + {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541GI_LF}, }; /* Function forward declarations */ @@ -646,6 +647,7 @@ e1000_set_mac_type(struct e1000_hw *hw) hw->mac_type = e1000_82546; break; case E1000_DEV_ID_82541ER: + case E1000_DEV_ID_82541GI_LF: hw->mac_type = e1000_82541_rev_2; break; default: diff --git a/drivers/net/e1000.h b/drivers/net/e1000.h index 851467d..23b2eb9 100644 --- a/drivers/net/e1000.h +++ b/drivers/net/e1000.h @@ -222,7 +222,8 @@ struct e1000_phy_stats { #define E1000_DEV_ID_82546EB_COPPER 0x1010 #define E1000_DEV_ID_82546EB_FIBER 0x1012 #define E1000_DEV_ID_82541ER 0x1078 -#define NUM_DEV_IDS 14 +#define E1000_DEV_ID_82541GI_LF 0x107C +#define NUM_DEV_IDS 15 #define NODE_ADDRESS_SIZE 6 #define ETH_LENGTH_OF_ADDRESS 6 -- cgit v1.1 From a101361bfe23c120321e45d114c0603b8e0763e9 Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Tue, 3 Jun 2008 15:26:21 +0200 Subject: DM9000: Add data bus-width auto detection. The U-boot DM9000x driver contains a compile time bus-width definition for the databus connected to the network controller. This compile check makes the code unclear, inflexible and is unneccessary. It can be asked to the network controller what its bus-width is by reading bits 6 and 7 of the interrupt status register. The linux kernel already uses a runtime mechanism to determine this bus-width, so the implementation below looks somewhat like that implementation. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 187 ++++++++++++++++++++++++++++++++++---------------- 1 file changed, 129 insertions(+), 58 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index 01e2f14..0a2ce68 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -36,7 +36,13 @@ v1.2 03/18/2003 Weilun Huang : -------------------------------------- - 12/15/2003 Initial port to u-boot by Sascha Hauer + 12/15/2003 Initial port to u-boot by + Sascha Hauer + + 06/03/2008 Remy Bohmer + - Added autodetect of databus width. + These changes are tested with DM9000{A,EP,E} together + with a 200MHz Atmel AT91SAM92161 core TODO: Homerun NIC and longrun NIC are not functional, only internal at the moment. @@ -84,8 +90,11 @@ typedef struct board_info { u8 device_wait_reset; /* device state */ u8 nic_type; /* NIC type */ unsigned char srom[128]; -} board_info_t; -board_info_t dmfe_info; + void (*outblk)(void *data_ptr, int count); + void (*inblk)(void *data_ptr, int count); + void (*rx_status)(u16 *RxStatus, u16 *RxLen); + } board_info_t; +static board_info_t dm9000_info; /* For module input parameter */ static int media_mode = DM9000_AUTO; @@ -127,7 +136,81 @@ dump_regs(void) DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(ISR)); DM9000_DBG("\n"); } -#endif /* */ +#endif + +static void dm9000_outblk_8bit(void *data_ptr, int count) +{ + int i; + for (i = 0; i < count; i++) + DM9000_outb((((u8 *) data_ptr)[i] & 0xff), DM9000_DATA); +} + +static void dm9000_outblk_16bit(void *data_ptr, int count) +{ + int i; + u32 tmplen = (count + 1) / 2; + + for (i = 0; i < tmplen; i++) + DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA); +} +static void dm9000_outblk_32bit(void *data_ptr, int count) +{ + int i; + u32 tmplen = (count + 3) / 4; + + for (i = 0; i < tmplen; i++) + DM9000_outl(((u32 *) data_ptr)[i], DM9000_DATA); +} + +static void dm9000_inblk_8bit(void *data_ptr, int count) +{ + int i; + for (i = 0; i < count; i++) + ((u8 *) data_ptr)[i] = DM9000_inb(DM9000_DATA); +} + +static void dm9000_inblk_16bit(void *data_ptr, int count) +{ + int i; + u32 tmplen = (count + 1) / 2; + + for (i = 0; i < tmplen; i++) + ((u16 *) data_ptr)[i] = DM9000_inw(DM9000_DATA); +} +static void dm9000_inblk_32bit(void *data_ptr, int count) +{ + int i; + u32 tmplen = (count + 3) / 4; + + for (i = 0; i < tmplen; i++) + ((u32 *) data_ptr)[i] = DM9000_inl(DM9000_DATA); +} + +static void dm9000_rx_status_32bit(u16 *RxStatus, u16 *RxLen) +{ + u32 tmpdata = DM9000_inl(DM9000_DATA); + + DM9000_outb(DM9000_MRCMD, DM9000_IO); + + *RxStatus = tmpdata; + *RxLen = tmpdata >> 16; +} + +static void dm9000_rx_status_16bit(u16 *RxStatus, u16 *RxLen) +{ + DM9000_outb(DM9000_MRCMD, DM9000_IO); + + *RxStatus = DM9000_inw(DM9000_DATA); + *RxLen = DM9000_inw(DM9000_DATA); +} + +static void dm9000_rx_status_8bit(u16 *RxStatus, u16 *RxLen) +{ + DM9000_outb(DM9000_MRCMD, DM9000_IO); + + *RxStatus = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8); + *RxLen = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8); +} /* Search DM9000 board, allocate space and register it @@ -236,7 +319,7 @@ program_dm9802(void) static void identify_nic(void) { - struct board_info *db = &dmfe_info; /* Point a board information structure */ + struct board_info *db = &dm9000_info; u16 phy_reg3; DM9000_iow(DM9000_NCR, NCR_EXT_PHY); phy_reg3 = phy_read(3); @@ -274,12 +357,46 @@ int eth_init(bd_t * bd) { int i, oft, lnk; + u8 io_mode; + struct board_info *db = &dm9000_info; + DM9000_DBG("eth_init()\n"); /* RESET device */ dm9000_reset(); dm9000_probe(); + /* Auto-detect 8/16/32 bit mode, ISR Bit 6+7 indicate bus width */ + io_mode = DM9000_ior(DM9000_ISR) >> 6; + + switch (io_mode) { + case 0x0: /* 16-bit mode */ + printf("DM9000: running in 16 bit mode\n"); + db->outblk = dm9000_outblk_16bit; + db->inblk = dm9000_inblk_16bit; + db->rx_status = dm9000_rx_status_16bit; + break; + case 0x01: /* 32-bit mode */ + printf("DM9000: running in 32 bit mode\n"); + db->outblk = dm9000_outblk_32bit; + db->inblk = dm9000_inblk_32bit; + db->rx_status = dm9000_rx_status_32bit; + break; + case 0x02: /* 8 bit mode */ + printf("DM9000: running in 8 bit mode\n"); + db->outblk = dm9000_outblk_8bit; + db->inblk = dm9000_inblk_8bit; + db->rx_status = dm9000_rx_status_8bit; + break; + default: + /* Assume 8 bit mode, will probably not work anyway */ + printf("DM9000: Undefined IO-mode:0x%x\n", io_mode); + db->outblk = dm9000_outblk_8bit; + db->inblk = dm9000_inblk_8bit; + db->rx_status = dm9000_rx_status_8bit; + break; + } + /* NIC Type: FASTETHER, HOMERUN, LONGRUN */ identify_nic(); @@ -377,6 +494,8 @@ eth_send(volatile void *packet, int length) char *data_ptr; u32 tmplen, i; int tmo; + struct board_info *db = &dm9000_info; + DM9000_DBG("eth_send: length: %d\n", length); for (i = 0; i < length; i++) { if (i % 8 == 0) @@ -388,24 +507,8 @@ eth_send(volatile void *packet, int length) data_ptr = (char *) packet; DM9000_outb(DM9000_MWCMD, DM9000_IO); -#ifdef CONFIG_DM9000_USE_8BIT - /* Byte mode */ - for (i = 0; i < length; i++) - DM9000_outb((data_ptr[i] & 0xff), DM9000_DATA); - -#endif /* */ -#ifdef CONFIG_DM9000_USE_16BIT - tmplen = (length + 1) / 2; - for (i = 0; i < tmplen; i++) - DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA); - -#endif /* */ -#ifdef CONFIG_DM9000_USE_32BIT - tmplen = (length + 3) / 4; - for (i = 0; i < tmplen; i++) - DM9000_outl(((u32 *) data_ptr)[i], DM9000_DATA); - -#endif /* */ + /* push the data to the TX-fifo */ + (db->outblk)(data_ptr, length); /* Set TX length to DM9000 */ DM9000_iow(DM9000_TXPLL, length & 0xff); @@ -450,10 +553,7 @@ eth_rx(void) { u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0]; u16 RxStatus, RxLen = 0; - u32 tmplen, i; -#ifdef CONFIG_DM9000_USE_32BIT - u32 tmpdata; -#endif + struct board_info *db = &dm9000_info; /* Check packet ready or not */ DM9000_ior(DM9000_MRCMDX); /* Dummy read */ @@ -472,43 +572,14 @@ eth_rx(void) /* A packet ready now & Get status/length */ DM9000_outb(DM9000_MRCMD, DM9000_IO); -#ifdef CONFIG_DM9000_USE_8BIT - RxStatus = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8); - RxLen = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8); + (db->rx_status)(&RxStatus, &RxLen); -#endif /* */ -#ifdef CONFIG_DM9000_USE_16BIT - RxStatus = DM9000_inw(DM9000_DATA); - RxLen = DM9000_inw(DM9000_DATA); - -#endif /* */ -#ifdef CONFIG_DM9000_USE_32BIT - tmpdata = DM9000_inl(DM9000_DATA); - RxStatus = tmpdata; - RxLen = tmpdata >> 16; - -#endif /* */ DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen); /* Move data from DM9000 */ /* Read received packet from RX SRAM */ -#ifdef CONFIG_DM9000_USE_8BIT - for (i = 0; i < RxLen; i++) - rdptr[i] = DM9000_inb(DM9000_DATA); - -#endif /* */ -#ifdef CONFIG_DM9000_USE_16BIT - tmplen = (RxLen + 1) / 2; - for (i = 0; i < tmplen; i++) - ((u16 *) rdptr)[i] = DM9000_inw(DM9000_DATA); + (db->inblk)(rdptr, RxLen); -#endif /* */ -#ifdef CONFIG_DM9000_USE_32BIT - tmplen = (RxLen + 3) / 4; - for (i = 0; i < tmplen; i++) - ((u32 *) rdptr)[i] = DM9000_inl(DM9000_DATA); - -#endif /* */ if ((RxStatus & 0xbf00) || (RxLen < 0x40) || (RxLen > DM9000_PKT_MAX)) { if (RxStatus & 0x100) { -- cgit v1.1 From 134e266253c02a7832560da59d394989c4f64453 Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Tue, 3 Jun 2008 15:26:22 +0200 Subject: DM9000: repair debug logging It seems that the debugging code of the DM9000x driver in U-boot has not been compiled for a long time, because it cannot compile... Also rearranged some loglines to get more useful info while debugging. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 33 +++++++++++++++++++++------------ 1 file changed, 21 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index 0a2ce68..05d07f3 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -41,6 +41,7 @@ v1.2 03/18/2003 Weilun Huang : 06/03/2008 Remy Bohmer - Added autodetect of databus width. + - Made debug code compile again. These changes are tested with DM9000{A,EP,E} together with a 200MHz Atmel AT91SAM92161 core @@ -65,10 +66,22 @@ TODO: Homerun NIC and longrun NIC are not functional, only internal at the /* #define CONFIG_DM9000_DEBUG */ #ifdef CONFIG_DM9000_DEBUG -#define DM9000_DBG(fmt,args...) printf(fmt ,##args) -#else /* */ +#define DM9000_DBG(fmt,args...) printf(fmt, ##args) +#define DM9000_DMP_PACKET(func,packet,length) \ + do { \ + int i; \ + printf(func ": length: %d\n", length); \ + for (i = 0; i < length; i++) { \ + if (i % 8 == 0) \ + printf("\n%s: %02x: ", func, i); \ + printf("%02x ", ((unsigned char *) packet)[i]); \ + } printf("\n"); \ + } while(0) +#else #define DM9000_DBG(fmt,args...) -#endif /* */ +#define DM9000_DMP_PACKET(func,packet,length) +#endif + enum DM9000_PHY_mode { DM9000_10MHD = 0, DM9000_100MHD = 1, DM9000_10MFD = 4, DM9000_100MFD = 5, DM9000_AUTO = 8, DM9000_1M_HPNA = 0x10 @@ -133,7 +146,7 @@ dump_regs(void) DM9000_DBG("TSRII (0x04): %02x\n", DM9000_ior(4)); DM9000_DBG("RCR (0x05): %02x\n", DM9000_ior(5)); DM9000_DBG("RSR (0x06): %02x\n", DM9000_ior(6)); - DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(ISR)); + DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(DM9000_ISR)); DM9000_DBG("\n"); } #endif @@ -496,12 +509,7 @@ eth_send(volatile void *packet, int length) int tmo; struct board_info *db = &dm9000_info; - DM9000_DBG("eth_send: length: %d\n", length); - for (i = 0; i < length; i++) { - if (i % 8 == 0) - DM9000_DBG("\nSend: 02x: ", i); - DM9000_DBG("%02x ", ((unsigned char *) packet)[i]); - } DM9000_DBG("\n"); + DM9000_DMP_PACKET("eth_send", packet, length); /* Move data to DM9000 TX RAM */ data_ptr = (char *) packet; @@ -596,6 +604,7 @@ eth_rx(void) dm9000_reset(); } } else { + DM9000_DMP_PACKET("eth_rx", rdptr, RxLen); /* Pass to upper layer */ DM9000_DBG("passing packet to upper layer\n"); @@ -666,7 +675,7 @@ phy_read(int reg) val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL); /* The read data keeps on REG_0D & REG_0E */ - DM9000_DBG("phy_read(%d): %d\n", reg, val); + DM9000_DBG("phy_read(0x%x): 0x%x\n", reg, val); return val; } @@ -686,6 +695,6 @@ phy_write(int reg, u16 value) DM9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */ udelay(500); /* Wait write complete */ DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */ - DM9000_DBG("phy_write(reg:%d, value:%d)\n", reg, value); + DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value); } #endif /* CONFIG_DRIVER_DM9000 */ -- cgit v1.1 From acba31847fad9ae40708cc2c9f3a634ec35f3416 Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Tue, 3 Jun 2008 15:26:23 +0200 Subject: DM9000: improve eth_send() routine The eth_send routine of the U-boot DM9000x driver does not match the DM9000 or DM9000A application notes/programming guides. This change improves the stability of the DM9000A network controller. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index 05d07f3..c6c24dd 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -42,6 +42,9 @@ v1.2 03/18/2003 Weilun Huang : 06/03/2008 Remy Bohmer - Added autodetect of databus width. - Made debug code compile again. + - Adapt eth_send such that it matches the DM9000* + application notes. Needed to make it work properly + for DM9000A. These changes are tested with DM9000{A,EP,E} together with a 200MHz Atmel AT91SAM92161 core @@ -505,15 +508,16 @@ int eth_send(volatile void *packet, int length) { char *data_ptr; - u32 tmplen, i; int tmo; struct board_info *db = &dm9000_info; DM9000_DMP_PACKET("eth_send", packet, length); + DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */ + /* Move data to DM9000 TX RAM */ data_ptr = (char *) packet; - DM9000_outb(DM9000_MWCMD, DM9000_IO); + DM9000_outb(DM9000_MWCMD, DM9000_IO); /* Prepare for TX-data */ /* push the data to the TX-fifo */ (db->outblk)(data_ptr, length); @@ -523,16 +527,19 @@ eth_send(volatile void *packet, int length) DM9000_iow(DM9000_TXPLH, (length >> 8) & 0xff); /* Issue TX polling command */ - DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */ + DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */ /* wait for end of transmission */ tmo = get_timer(0) + 5 * CFG_HZ; - while (DM9000_ior(DM9000_TCR) & TCR_TXREQ) { + while ( !(DM9000_ior(DM9000_NSR) & (NSR_TX1END | NSR_TX2END)) || + !(DM9000_ior(DM9000_ISR) & IMR_PTM) ) { if (get_timer(0) >= tmo) { printf("transmission timeout\n"); break; } } + DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */ + DM9000_DBG("transmit done\n\n"); return 0; } -- cgit v1.1 From fbcb7ece0ea1e364180f1cf963e0fa0ce7f6560d Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Tue, 3 Jun 2008 15:26:24 +0200 Subject: DM9000: Improve eth_reset() routine According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the reset procedure must be done twice to properly reset the DM9000 by means of software. This errata is not needed anymore for the DM9000A, but it does not bother it. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 34 +++++++++++++++++++++++++++++++--- 1 file changed, 31 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index c6c24dd..5b00e95 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -45,6 +45,8 @@ v1.2 03/18/2003 Weilun Huang : - Adapt eth_send such that it matches the DM9000* application notes. Needed to make it work properly for DM9000A. + - Adapted reset procedure to match DM9000 application + notes (i.e. double reset) These changes are tested with DM9000{A,EP,E} together with a 200MHz Atmel AT91SAM92161 core @@ -362,9 +364,35 @@ identify_nic(void) static void dm9000_reset(void) { - DM9000_DBG("resetting\n"); - DM9000_iow(DM9000_NCR, NCR_RST); - udelay(1000); /* delay 1ms */ + DM9000_DBG("resetting DM9000\n"); + + /* Reset DM9000, + see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */ + + /* DEBUG: Make all GPIO pins outputs */ + DM9000_iow(DM9000_GPCR, 0x0F); + /* Step 1: Power internal PHY by writing 0 to GPIO0 pin */ + DM9000_iow(DM9000_GPR, 0); + /* Step 2: Software reset */ + DM9000_iow(DM9000_NCR, 3); + + do { + DM9000_DBG("resetting the DM9000, 1st reset\n"); + udelay(25); /* Wait at least 20 us */ + } while (DM9000_ior(DM9000_NCR) & 1); + + DM9000_iow(DM9000_NCR, 0); + DM9000_iow(DM9000_NCR, 3); /* Issue a second reset */ + + do { + DM9000_DBG("resetting the DM9000, 2nd reset\n"); + udelay(25); /* Wait at least 20 us */ + } while (DM9000_ior(DM9000_NCR) & 1); + + /* Check whether the ethernet controller is present */ + if ((DM9000_ior(DM9000_PIDL) != 0x0) || + (DM9000_ior(DM9000_PIDH) != 0x90)) + printf("ERROR: resetting DM9000 -> not responding\n"); } /* Initilize dm9000 board -- cgit v1.1 From 850ba7555dbd4ca8d14fc475b864d534797adab3 Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Tue, 3 Jun 2008 15:26:25 +0200 Subject: DM9000: Make driver work properly for DM9000A The DM9000A network controller does not work with the U-boot DM9000x driver. Analysis showed that many incoming packets are lost. The DM9000A Application Notes V1.20 (section 5.6.1) recommend that the poll to check for a valid rx packet be done on the interrupt status register, not directly by performing the dummy read and the rx status check as is currently the case in the u-boot driver. When the recommended poll is done as suggested the driver starts working correctly on 10Mbit/HD, but on 100MBit/FD packets come in faster so that there can be more than 1 package in the fifo at the same time. The driver must perform the rx-status check in a loop and read and handle all packages until there is no more left _after_ the interrupt RX flag is set. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 93 ++++++++++++++++++++++++++++++--------------------- 1 file changed, 54 insertions(+), 39 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index 5b00e95..08248f4 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -40,6 +40,10 @@ v1.2 03/18/2003 Weilun Huang : Sascha Hauer 06/03/2008 Remy Bohmer + - Fixed the driver to work with DM9000A. + (check on ISR receive status bit before reading the + FIFO as described in DM9000 programming guide and + application notes) - Added autodetect of databus width. - Made debug code compile again. - Adapt eth_send such that it matches the DM9000* @@ -598,53 +602,64 @@ eth_rx(void) u16 RxStatus, RxLen = 0; struct board_info *db = &dm9000_info; - /* Check packet ready or not */ - DM9000_ior(DM9000_MRCMDX); /* Dummy read */ - rxbyte = DM9000_inb(DM9000_DATA); /* Got most updated data */ - if (rxbyte == 0) + /* Check packet ready or not, we must check + the ISR status first for DM9000A */ + if (!(DM9000_ior(DM9000_ISR) & 0x01)) /* Rx-ISR bit must be set. */ return 0; - /* Status check: this byte must be 0 or 1 */ - if (rxbyte > 1) { - DM9000_iow(DM9000_RCR, 0x00); /* Stop Device */ - DM9000_iow(DM9000_ISR, 0x80); /* Stop INT request */ - DM9000_DBG("rx status check: %d\n", rxbyte); - } - DM9000_DBG("receiving packet\n"); + DM9000_iow(DM9000_ISR, 0x01); /* clear PR status latched in bit 0 */ - /* A packet ready now & Get status/length */ - DM9000_outb(DM9000_MRCMD, DM9000_IO); + /* There is _at least_ 1 package in the fifo, read them all */ + for (;;) { + DM9000_ior(DM9000_MRCMDX); /* Dummy read */ - (db->rx_status)(&RxStatus, &RxLen); + /* Get most updated data */ + rxbyte = DM9000_inb(DM9000_DATA); - DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen); + /* Status check: this byte must be 0 or 1 */ + if (rxbyte > DM9000_PKT_RDY) { + DM9000_iow(DM9000_RCR, 0x00); /* Stop Device */ + DM9000_iow(DM9000_ISR, 0x80); /* Stop INT request */ + printf("DM9000 error: status check fail: 0x%x\n", + rxbyte); + return 0; + } - /* Move data from DM9000 */ - /* Read received packet from RX SRAM */ - (db->inblk)(rdptr, RxLen); + if (rxbyte != DM9000_PKT_RDY) + return 0; /* No packet received, ignore */ + + DM9000_DBG("receiving packet\n"); + + /* A packet ready now & Get status/length */ + (db->rx_status)(&RxStatus, &RxLen); + + DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen); + + /* Move data from DM9000 */ + /* Read received packet from RX SRAM */ + (db->inblk)(rdptr, RxLen); + + if ((RxStatus & 0xbf00) || (RxLen < 0x40) + || (RxLen > DM9000_PKT_MAX)) { + if (RxStatus & 0x100) { + printf("rx fifo error\n"); + } + if (RxStatus & 0x200) { + printf("rx crc error\n"); + } + if (RxStatus & 0x8000) { + printf("rx length error\n"); + } + if (RxLen > DM9000_PKT_MAX) { + printf("rx length too big\n"); + dm9000_reset(); + } + } else { + DM9000_DMP_PACKET("eth_rx", rdptr, RxLen); - if ((RxStatus & 0xbf00) || (RxLen < 0x40) - || (RxLen > DM9000_PKT_MAX)) { - if (RxStatus & 0x100) { - printf("rx fifo error\n"); + DM9000_DBG("passing packet to upper layer\n"); + NetReceive(NetRxPackets[0], RxLen); } - if (RxStatus & 0x200) { - printf("rx crc error\n"); - } - if (RxStatus & 0x8000) { - printf("rx length error\n"); - } - if (RxLen > DM9000_PKT_MAX) { - printf("rx length too big\n"); - dm9000_reset(); - } - } else { - DM9000_DMP_PACKET("eth_rx", rdptr, RxLen); - - /* Pass to upper layer */ - DM9000_DBG("passing packet to upper layer\n"); - NetReceive(NetRxPackets[0], RxLen); - return RxLen; } return 0; } -- cgit v1.1 From 98291e2e689096420465074cce926b226d2e71b4 Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Tue, 3 Jun 2008 15:26:26 +0200 Subject: DM9000: Some minor code cleanups Some lines of the U-boot DM9000x driver are longer than 80 characters, or need some other minor cleanup. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 41 ++++++++++++++++++++++++++--------------- 1 file changed, 26 insertions(+), 15 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index 08248f4..2945995 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -51,6 +51,7 @@ v1.2 03/18/2003 Weilun Huang : for DM9000A. - Adapted reset procedure to match DM9000 application notes (i.e. double reset) + - some minor code cleanups These changes are tested with DM9000{A,EP,E} together with a 200MHz Atmel AT91SAM92161 core @@ -115,7 +116,7 @@ typedef struct board_info { void (*outblk)(void *data_ptr, int count); void (*inblk)(void *data_ptr, int count); void (*rx_status)(u16 *RxStatus, u16 *RxLen); - } board_info_t; +} board_info_t; static board_info_t dm9000_info; /* For module input parameter */ @@ -454,15 +455,22 @@ eth_init(bd_t * bd) /* Set PHY */ set_PHY_mode(); - /* Program operating register */ - DM9000_iow(DM9000_NCR, 0x0); /* only intern phy supported by now */ - DM9000_iow(DM9000_TCR, 0); /* TX Polling clear */ - DM9000_iow(DM9000_BPTR, 0x3f); /* Less 3Kb, 200us */ - DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8)); /* Flow Control : High/Low Water */ - DM9000_iow(DM9000_FCR, 0x0); /* SH FIXME: This looks strange! Flow Control */ - DM9000_iow(DM9000_SMCR, 0); /* Special Mode */ - DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); /* clear TX status */ - DM9000_iow(DM9000_ISR, 0x0f); /* Clear interrupt status */ + /* Program operating register, only intern phy supported by now */ + DM9000_iow(DM9000_NCR, 0x0); + /* TX Polling clear */ + DM9000_iow(DM9000_TCR, 0); + /* Less 3Kb, 200us */ + DM9000_iow(DM9000_BPTR, 0x3f); + /* Flow Control : High/Low Water */ + DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8)); + /* SH FIXME: This looks strange! Flow Control */ + DM9000_iow(DM9000_FCR, 0x0); + /* Special Mode */ + DM9000_iow(DM9000_SMCR, 0); + /* clear TX status */ + DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); + /* Clear interrupt status */ + DM9000_iow(DM9000_ISR, 0x0f); /* Set Node address */ for (i = 0; i < 6; i++) @@ -496,8 +504,11 @@ eth_init(bd_t * bd) DM9000_DBG("\n"); /* Activate DM9000 */ - DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN); /* RX enable */ - DM9000_iow(DM9000_IMR, IMR_PAR); /* Enable TX/RX interrupt mask */ + /* RX enable */ + DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN); + /* Enable TX/RX interrupt mask */ + DM9000_iow(DM9000_IMR, IMR_PAR); + i = 0; while (!(phy_read(1) & 0x20)) { /* autonegation complete bit */ udelay(1000); @@ -720,7 +731,7 @@ phy_read(int reg) /* Fill the phyxcer register into REG_0C */ DM9000_iow(DM9000_EPAR, DM9000_PHY | reg); DM9000_iow(DM9000_EPCR, 0xc); /* Issue phyxcer read command */ - udelay(100); /* Wait read complete */ + udelay(100); /* Wait read complete */ DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer read command */ val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL); @@ -743,8 +754,8 @@ phy_write(int reg, u16 value) DM9000_iow(DM9000_EPDRL, (value & 0xff)); DM9000_iow(DM9000_EPDRH, ((value >> 8) & 0xff)); DM9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */ - udelay(500); /* Wait write complete */ + udelay(500); /* Wait write complete */ DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */ DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value); } -#endif /* CONFIG_DRIVER_DM9000 */ +#endif /* CONFIG_DRIVER_DM9000 */ -- cgit v1.1 From d6ee5fa40c26970d39990c6fc4a2f20a97822650 Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Wed, 4 Jun 2008 10:47:25 +0200 Subject: Fix order for reading rx-status registers in 32bit mode of DM9000 A last minute cleanup before submitting the DM9000A patch series yesterday introduced a bug in reading the rx-status registers in 32bit mode only. This patch repairs this. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index 2945995..6f3ddf0 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -211,10 +211,11 @@ static void dm9000_inblk_32bit(void *data_ptr, int count) static void dm9000_rx_status_32bit(u16 *RxStatus, u16 *RxLen) { - u32 tmpdata = DM9000_inl(DM9000_DATA); + u32 tmpdata; DM9000_outb(DM9000_MRCMD, DM9000_IO); + tmpdata = DM9000_inl(DM9000_DATA); *RxStatus = tmpdata; *RxLen = tmpdata >> 16; } -- cgit v1.1 From 0e38c938ed4bcadb4f4fc1419a541431e94fc202 Mon Sep 17 00:00:00 2001 From: Remy Bohmer Date: Thu, 5 Jun 2008 13:03:36 +0200 Subject: DM9000 fix status check fail 0x6d error for trizeps board According to the Application Notes of the DM9000, only the 2 bits 0:1 of the status byte need to be checked to identify a valid packet in the fifo But, The several different Application Notes do not all speak the same language on these bits. They do not disagree, but only 1 Application Note noted explicitly that only these 2 bits need to be checked. Even the datasheets do not mention anything about these 2 bits. Because the old code, and the kernel check the whole byte, I left this piece untouched. However, I tested all board/DM9000[A|E|EP] devices with this 2 bit check, so it should work. Notice, that the 2nd iteration through this receive loop (when a 2nd packet is in the fifo) is much shorter now, compared to the older U-boot driver code, so that we can maybe run into a hardware condition now that was never seen before, or maybe was seen very unfrequently. Additionaly added a cleanup of a stack variable. Signed-off-by: Remy Bohmer Signed-off-by: Ben Warren --- drivers/net/dm9000x.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index 6f3ddf0..c2144d9 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -113,7 +113,7 @@ typedef struct board_info { u8 device_wait_reset; /* device state */ u8 nic_type; /* NIC type */ unsigned char srom[128]; - void (*outblk)(void *data_ptr, int count); + void (*outblk)(volatile void *data_ptr, int count); void (*inblk)(void *data_ptr, int count); void (*rx_status)(u16 *RxStatus, u16 *RxLen); } board_info_t; @@ -161,14 +161,14 @@ dump_regs(void) } #endif -static void dm9000_outblk_8bit(void *data_ptr, int count) +static void dm9000_outblk_8bit(volatile void *data_ptr, int count) { int i; for (i = 0; i < count; i++) DM9000_outb((((u8 *) data_ptr)[i] & 0xff), DM9000_DATA); } -static void dm9000_outblk_16bit(void *data_ptr, int count) +static void dm9000_outblk_16bit(volatile void *data_ptr, int count) { int i; u32 tmplen = (count + 1) / 2; @@ -176,7 +176,7 @@ static void dm9000_outblk_16bit(void *data_ptr, int count) for (i = 0; i < tmplen; i++) DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA); } -static void dm9000_outblk_32bit(void *data_ptr, int count) +static void dm9000_outblk_32bit(volatile void *data_ptr, int count) { int i; u32 tmplen = (count + 3) / 4; @@ -551,7 +551,6 @@ eth_init(bd_t * bd) int eth_send(volatile void *packet, int length) { - char *data_ptr; int tmo; struct board_info *db = &dm9000_info; @@ -560,11 +559,10 @@ eth_send(volatile void *packet, int length) DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */ /* Move data to DM9000 TX RAM */ - data_ptr = (char *) packet; DM9000_outb(DM9000_MWCMD, DM9000_IO); /* Prepare for TX-data */ /* push the data to the TX-fifo */ - (db->outblk)(data_ptr, length); + (db->outblk)(packet, length); /* Set TX length to DM9000 */ DM9000_iow(DM9000_TXPLL, length & 0xff); @@ -625,8 +623,9 @@ eth_rx(void) for (;;) { DM9000_ior(DM9000_MRCMDX); /* Dummy read */ - /* Get most updated data */ - rxbyte = DM9000_inb(DM9000_DATA); + /* Get most updated data, + only look at bits 0:1, See application notes DM9000 */ + rxbyte = DM9000_inb(DM9000_DATA) & 0x03; /* Status check: this byte must be 0 or 1 */ if (rxbyte > DM9000_PKT_RDY) { -- cgit v1.1 From 3b904ccb93c3196727e2e9870cb1df903cab19ad Mon Sep 17 00:00:00 2001 From: Shinya Kuribayashi Date: Mon, 9 Jun 2008 23:37:44 +0900 Subject: net: Conditional COBJS inclusion of network drivers Replace COBJS-y with appropriate driver config names. Signed-off-by: Shinya Kuribayashi Signed-off-by: Ben Warren --- drivers/net/3c589.c | 5 ---- drivers/net/Makefile | 66 +++++++++++++++++++++++----------------------- drivers/net/bcm570x.c | 5 ---- drivers/net/cs8900.c | 8 ------ drivers/net/dc2114x.c | 6 ----- drivers/net/dm9000x.c | 3 --- drivers/net/e1000.c | 5 ---- drivers/net/eepro100.c | 5 ---- drivers/net/enc28j60.c | 3 --- drivers/net/fsl_mcdmafec.c | 5 ---- drivers/net/inca-ip_sw.c | 5 ---- drivers/net/ks8695eth.c | 4 --- drivers/net/lan91c96.c | 9 ------- drivers/net/macb.c | 5 ---- drivers/net/mcffec.c | 7 ----- drivers/net/natsemi.c | 5 ---- drivers/net/netarm_eth.c | 8 ------ drivers/net/netconsole.c | 5 ---- drivers/net/ns7520_eth.c | 5 ---- drivers/net/ns8382x.c | 5 ---- drivers/net/ns9750_eth.c | 4 --- drivers/net/pcnet.c | 4 --- drivers/net/plb2800_eth.c | 6 ----- drivers/net/rtl8019.c | 8 ------ drivers/net/rtl8139.c | 4 --- drivers/net/rtl8169.c | 5 ---- drivers/net/s3c4510b_eth.c | 5 ---- drivers/net/smc91111.c | 3 --- drivers/net/smc911x.c | 5 ---- drivers/net/tigon3.c | 5 +--- drivers/net/tsec.c | 3 --- drivers/net/tsi108_eth.c | 5 ---- drivers/net/uli526x.c | 4 --- drivers/net/vsc7385.c | 5 ---- 34 files changed, 34 insertions(+), 201 deletions(-) (limited to 'drivers') diff --git a/drivers/net/3c589.c b/drivers/net/3c589.c index 3f1e770..0cf8dff 100644 --- a/drivers/net/3c589.c +++ b/drivers/net/3c589.c @@ -26,8 +26,6 @@ #include #include -#ifdef CONFIG_DRIVER_3C589 - #include "3c589.h" @@ -514,6 +512,3 @@ int eth_send(volatile void *packet, int length) { return length; } - - -#endif /* CONFIG_DRIVER_3C589 */ diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 5b031c9..84be288 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -25,45 +25,45 @@ include $(TOPDIR)/config.mk LIB := $(obj)libnet.a -COBJS-y += 3c589.o -COBJS-y += bcm570x.o bcm570x_autoneg.o 5701rls.o +COBJS-$(CONFIG_DRIVER_3C589) += 3c589.o +COBJS-$(CONFIG_BCM570x) += bcm570x.o bcm570x_autoneg.o 5701rls.o COBJS-$(CONFIG_BFIN_MAC) += bfin_mac.o -COBJS-y += cs8900.o -COBJS-y += dc2114x.o -COBJS-y += dm9000x.o -COBJS-y += e1000.o -COBJS-y += eepro100.o -COBJS-y += enc28j60.o -COBJS-y += fsl_mcdmafec.o +COBJS-$(CONFIG_DRIVER_CS8900) += cs8900.o +COBJS-$(CONFIG_TULIP) += dc2114x.o +COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o +COBJS-$(CONFIG_E1000) += e1000.o +COBJS-$(CONFIG_EEPRO100) += eepro100.o +COBJS-$(CONFIG_ENC28J60) += enc28j60.o +COBJS-$(CONFIG_FSLDMAFEC) += fsl_mcdmafec.o COBJS-$(CONFIG_GRETH) += greth.o -COBJS-y += inca-ip_sw.o -COBJS-y += ks8695eth.o -COBJS-y += lan91c96.o -COBJS-y += macb.o -COBJS-y += mcffec.o -COBJS-y += natsemi.o +COBJS-$(CONFIG_INCA_IP_SWITCH) += inca-ip_sw.o +COBJS-$(CONFIG_DRIVER_KS8695ETH) += ks8695eth.o +COBJS-$(CONFIG_DRIVER_LAN91C96) += lan91c96.o +COBJS-$(CONFIG_MACB) += macb.o +COBJS-$(CONFIG_MCFFEC) += mcffec.o +COBJS-$(CONFIG_NATSEMI) += natsemi.o ifeq ($(CONFIG_DRIVER_NE2000),y) COBJS-y += ne2000.o COBJS-$(CONFIG_DRIVER_AX88796L) += ax88796.o endif -COBJS-y += netarm_eth.o -COBJS-y += netconsole.o -COBJS-y += ns7520_eth.o -COBJS-y += ns8382x.o -COBJS-y += ns9750_eth.o -COBJS-y += pcnet.o -COBJS-y += plb2800_eth.o -COBJS-y += rtl8019.o -COBJS-y += rtl8139.o -COBJS-y += rtl8169.o -COBJS-y += s3c4510b_eth.o -COBJS-y += smc91111.o -COBJS-y += smc911x.o -COBJS-y += tigon3.o -COBJS-y += tsec.o -COBJS-y += tsi108_eth.o -COBJS-y += uli526x.o -COBJS-y += vsc7385.o +COBJS-$(CONFIG_DRIVER_NETARMETH) += netarm_eth.o +COBJS-$(CONFIG_NETCONSOLE) += netconsole.o +COBJS-$(CONFIG_DRIVER_NS7520_ETHERNET) += ns7520_eth.o +COBJS-$(CONFIG_NS8382X) += ns8382x.o +COBJS-$(CONFIG_DRIVER_NS9750_ETHERNET) += ns9750_eth.o +COBJS-$(CONFIG_PCNET) += pcnet.o +COBJS-$(CONFIG_PLB2800_ETHER) += plb2800_eth.o +COBJS-$(CONFIG_DRIVER_RTL8019) += rtl8019.o +COBJS-$(CONFIG_RTL8139) += rtl8139.o +COBJS-$(CONFIG_RTL8169) += rtl8169.o +COBJS-$(CONFIG_DRIVER_S3C4510_ETH) += s3c4510b_eth.o +COBJS-$(CONFIG_DRIVER_SMC91111) += smc91111.o +COBJS-$(CONFIG_DRIVER_SMC911X) += smc911x.o +COBJS-$(CONFIG_TIGON3) += tigon3.o bcm570x_autoneg.o 5701rls.o +COBJS-$(CONFIG_TSEC_ENET) += tsec.o +COBJS-$(CONFIG_TSI108_ETH) += tsi108_eth.o +COBJS-$(CONFIG_ULI526X) += uli526x.o +COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o COBJS-$(CONFIG_XILINX_EMAC) += xilinx_emac.o COBJS-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o diff --git a/drivers/net/bcm570x.c b/drivers/net/bcm570x.c index 5ad31d1..6b28b95 100644 --- a/drivers/net/bcm570x.c +++ b/drivers/net/bcm570x.c @@ -6,9 +6,6 @@ #include -#if defined(CONFIG_CMD_NET) \ - && (!defined(CONFIG_NET_MULTI)) && defined(CONFIG_BCM570x) - #ifdef CONFIG_BMW #include #endif @@ -1599,5 +1596,3 @@ PQQ_ENTRY QQ_GetTail (PQQ_CONTAINER pQueue, unsigned int Idx) return pQueue->Array[Idx]; } - -#endif diff --git a/drivers/net/cs8900.c b/drivers/net/cs8900.c index 458b517..ae1983a 100644 --- a/drivers/net/cs8900.c +++ b/drivers/net/cs8900.c @@ -41,10 +41,6 @@ #include "cs8900.h" #include -#ifdef CONFIG_DRIVER_CS8900 - -#if defined(CONFIG_CMD_NET) - #undef DEBUG /* packet page register access functions */ @@ -315,7 +311,3 @@ int cs8900_e2prom_write(unsigned char addr, unsigned short value) return 0; } - -#endif /* CONFIG_CMD_NET */ - -#endif /* CONFIG_DRIVER_CS8900 */ diff --git a/drivers/net/dc2114x.c b/drivers/net/dc2114x.c index 1d728d8..8117239 100644 --- a/drivers/net/dc2114x.c +++ b/drivers/net/dc2114x.c @@ -19,10 +19,6 @@ */ #include - -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_TULIP) - #include #include #include @@ -766,5 +762,3 @@ static void update_srom(struct eth_device *dev, bd_t *bis) } } #endif /* UPDATE_SROM */ - -#endif diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c index fa95a73..844fb76 100644 --- a/drivers/net/dm9000x.c +++ b/drivers/net/dm9000x.c @@ -64,8 +64,6 @@ TODO: Homerun NIC and longrun NIC are not functional, only internal at the #include #include -#ifdef CONFIG_DRIVER_DM9000 - #include "dm9000x.h" /* Board/System/Debug information/definition ---------------- */ @@ -760,4 +758,3 @@ phy_write(int reg, u16 value) DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */ DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value); } -#endif /* CONFIG_DRIVER_DM9000 */ diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c index 40a781f..c31029a 100644 --- a/drivers/net/e1000.c +++ b/drivers/net/e1000.c @@ -44,9 +44,6 @@ tested on both gig copper and gig fiber boards #include "e1000.h" -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_E1000) - #define TOUT_LOOP 100000 #undef virt_to_bus @@ -3061,5 +3058,3 @@ e1000_initialize(bd_t * bis) } return 1; } - -#endif diff --git a/drivers/net/eepro100.c b/drivers/net/eepro100.c index 96ed271..9de0fb5 100644 --- a/drivers/net/eepro100.c +++ b/drivers/net/eepro100.c @@ -30,9 +30,6 @@ #undef DEBUG -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_EEPRO100) - /* Ethernet chip registers. */ #define SCBStatus 0 /* Rx/Command Unit Status *Word* */ @@ -944,5 +941,3 @@ static void read_hw_addr (struct eth_device *dev, bd_t * bis) #endif } } - -#endif diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60.c index 98303ac..5c24b0d 100644 --- a/drivers/net/enc28j60.c +++ b/drivers/net/enc28j60.c @@ -17,7 +17,6 @@ #include #include -#ifdef CONFIG_ENC28J60 #include #include #include @@ -979,5 +978,3 @@ static void phyWrite(unsigned char addr, unsigned short data) } } } - -#endif /* CONFIG_ENC28J60 */ diff --git a/drivers/net/fsl_mcdmafec.c b/drivers/net/fsl_mcdmafec.c index 2ef91f2..f2bdba6 100644 --- a/drivers/net/fsl_mcdmafec.c +++ b/drivers/net/fsl_mcdmafec.c @@ -31,7 +31,6 @@ #include #include -#ifdef CONFIG_FSLDMAFEC #undef ET_DEBUG #undef MII_DEBUG @@ -49,7 +48,6 @@ #define BD_ENET_RX_ERR (BD_ENET_RX_LG | BD_ENET_RX_NO | BD_ENET_RX_CR | \ BD_ENET_RX_OV | BD_ENET_RX_TR) -#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) #include #include @@ -586,6 +584,3 @@ int mcdmafec_initialize(bd_t * bis) return 1; } - -#endif /* CONFIG_CMD_NET && CONFIG_NET_MULTI */ -#endif /* CONFIG_FSLDMAFEC */ diff --git a/drivers/net/inca-ip_sw.c b/drivers/net/inca-ip_sw.c index e4aaed6..ffdd1f3 100644 --- a/drivers/net/inca-ip_sw.c +++ b/drivers/net/inca-ip_sw.c @@ -26,9 +26,6 @@ #include -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_INCA_IP_SWITCH) - #include #include #include @@ -813,5 +810,3 @@ Fail: return -1; } #endif /* CONFIG_INCA_IP_SWITCH_AMDIX */ - -#endif diff --git a/drivers/net/ks8695eth.c b/drivers/net/ks8695eth.c index b598dd7..7f3e0c2 100644 --- a/drivers/net/ks8695eth.c +++ b/drivers/net/ks8695eth.c @@ -21,8 +21,6 @@ /****************************************************************************/ #include - -#ifdef CONFIG_DRIVER_KS8695ETH #include #include #include @@ -234,5 +232,3 @@ int eth_send(volatile void *packet, int len) return len; } - -#endif /* CONFIG_DRIVER_KS8695ETH */ diff --git a/drivers/net/lan91c96.c b/drivers/net/lan91c96.c index 51cfb7e..c23a400 100644 --- a/drivers/net/lan91c96.c +++ b/drivers/net/lan91c96.c @@ -63,10 +63,6 @@ #include "lan91c96.h" #include -#ifdef CONFIG_DRIVER_LAN91C96 - -#if defined(CONFIG_CMD_NET) - /*------------------------------------------------------------------------ * * Configuration options, for the experienced user to change. @@ -865,9 +861,6 @@ static int smc_hw_init () } #endif /* 0 */ -#endif /* CONFIG_CMD_NET */ - - /* smc_get_ethaddr (bd_t * bd) * * This checks both the environment and the ROM for an ethernet address. If @@ -963,5 +956,3 @@ int get_rom_mac (unsigned char *v_rom_mac) return (1); #endif } - -#endif /* CONFIG_DRIVER_LAN91C96 */ diff --git a/drivers/net/macb.c b/drivers/net/macb.c index e5733f6..aa39284 100644 --- a/drivers/net/macb.c +++ b/drivers/net/macb.c @@ -17,9 +17,6 @@ */ #include -#if defined(CONFIG_MACB) \ - && (defined(CONFIG_CMD_NET) || defined(CONFIG_CMD_MII)) - /* * The u-boot networking stack is a little weird. It seems like the * networking core allocates receive buffers up front without any @@ -593,5 +590,3 @@ int miiphy_write(unsigned char addr, unsigned char reg, unsigned short value) } #endif - -#endif /* CONFIG_MACB */ diff --git a/drivers/net/mcffec.c b/drivers/net/mcffec.c index 8d4e248..58ed5e3 100644 --- a/drivers/net/mcffec.c +++ b/drivers/net/mcffec.c @@ -27,8 +27,6 @@ #include #include -#ifdef CONFIG_MCFFEC - #include #include @@ -51,8 +49,6 @@ DECLARE_GLOBAL_DATA_PTR; -#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) - struct fec_info_s fec_info[] = { #ifdef CFG_FEC0_IOBASE { @@ -605,6 +601,3 @@ int mcffec_initialize(bd_t * bis) return 1; } - -#endif /* CONFIG_CMD_NET, FEC_ENET & NET_MULTI */ -#endif /* CONFIG_MCFFEC */ diff --git a/drivers/net/natsemi.c b/drivers/net/natsemi.c index a523959..4aee048 100644 --- a/drivers/net/natsemi.c +++ b/drivers/net/natsemi.c @@ -56,9 +56,6 @@ #include #include -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_NATSEMI) - /* defines */ #define EEPROM_SIZE 0xb /*12 16-bit chunks, or 24 bytes*/ @@ -878,5 +875,3 @@ natsemi_disable(struct eth_device *dev) /* Restore PME enable bit */ OUTL(dev, SavedClkRun, ClkRun); } - -#endif diff --git a/drivers/net/netarm_eth.c b/drivers/net/netarm_eth.c index ecf45dc..c011809 100644 --- a/drivers/net/netarm_eth.c +++ b/drivers/net/netarm_eth.c @@ -22,15 +22,11 @@ #include - -#ifdef CONFIG_DRIVER_NETARMETH #include #include #include "netarm_eth.h" #include -#if defined(CONFIG_CMD_NET) - static int na_mii_poll_busy (void); static void na_get_mac_addr (void) @@ -352,7 +348,3 @@ extern int eth_send (volatile void *packet, int length) printf ("eth_send timeout\n"); return 1; } - -#endif /* CONFIG_CMD_NET */ - -#endif /* CONFIG_DRIVER_NETARMETH */ diff --git a/drivers/net/netconsole.c b/drivers/net/netconsole.c index 69089f9..b2ee5ea 100644 --- a/drivers/net/netconsole.c +++ b/drivers/net/netconsole.c @@ -22,9 +22,6 @@ */ #include - -#ifdef CONFIG_NETCONSOLE - #include #include #include @@ -263,5 +260,3 @@ int drv_nc_init (void) return (rc == 0) ? 1 : rc; } - -#endif /* CONFIG_NETCONSOLE */ diff --git a/drivers/net/ns7520_eth.c b/drivers/net/ns7520_eth.c index a5a20df..37411df 100644 --- a/drivers/net/ns7520_eth.c +++ b/drivers/net/ns7520_eth.c @@ -15,8 +15,6 @@ #include -#if defined(CONFIG_DRIVER_NS7520_ETHERNET) - #include /* NetSendPacket */ #include #include @@ -846,14 +844,11 @@ extern int ns7520_miiphy_write(char *devname, unsigned char const addr, return (ret); } #endif /* defined(CONFIG_MII) */ -#endif /* CONFIG_DRIVER_NS7520_ETHERNET */ int ns7520_miiphy_initialize(bd_t *bis) { -#if defined(CONFIG_DRIVER_NS7520_ETHERNET) #if defined(CONFIG_MII) miiphy_register("ns7520phy", ns7520_miiphy_read, ns7520_miiphy_write); #endif -#endif return 0; } diff --git a/drivers/net/ns8382x.c b/drivers/net/ns8382x.c index c807dd4..0b9a3ae 100644 --- a/drivers/net/ns8382x.c +++ b/drivers/net/ns8382x.c @@ -56,9 +56,6 @@ #include #include -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_NS8382X) - /* defines */ #define DSIZE 0x00000FFF #define ETH_ALEN 6 @@ -859,5 +856,3 @@ ns8382x_disable(struct eth_device *dev) /* Restore PME enable bit */ OUTL(dev, SavedClkRun, ClkRun); } - -#endif diff --git a/drivers/net/ns9750_eth.c b/drivers/net/ns9750_eth.c index 067ff8e..0559710 100644 --- a/drivers/net/ns9750_eth.c +++ b/drivers/net/ns9750_eth.c @@ -37,8 +37,6 @@ #include "ns9750_eth.h" /* for Ethernet and PHY */ -#ifdef CONFIG_DRIVER_NS9750_ETHERNET - /* some definition to make transistion to linux easier */ #define NS9750_DRIVER_NAME "eth" @@ -793,5 +791,3 @@ static unsigned int ns9750_mii_poll_busy (void) return unTimeout; } - -#endif /* CONFIG_DRIVER_NS9750_ETHERNET */ diff --git a/drivers/net/pcnet.c b/drivers/net/pcnet.c index aa04e8f..a4f0214 100644 --- a/drivers/net/pcnet.c +++ b/drivers/net/pcnet.c @@ -45,9 +45,6 @@ #define PCNET_DEBUG2(fmt,args...) #endif -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_PCNET) - #if !defined(CONF_PCNET_79C973) && defined(CONF_PCNET_79C975) #error "Macro for PCnet chip version is not defined!" #endif @@ -537,4 +534,3 @@ static void pcnet_halt (struct eth_device *dev) printf ("%s: TIMEOUT: controller reset failed\n", dev->name); } } -#endif diff --git a/drivers/net/plb2800_eth.c b/drivers/net/plb2800_eth.c index b8cc57a..dad842c 100644 --- a/drivers/net/plb2800_eth.c +++ b/drivers/net/plb2800_eth.c @@ -24,10 +24,6 @@ */ #include - -#if defined(CONFIG_CMD_NET) \ - && defined(CONFIG_NET_MULTI) && defined(CONFIG_PLB2800_ETHER) - #include #include #include @@ -392,5 +388,3 @@ static unsigned char * plb2800_get_mac_addr(void) return addr; } - -#endif /* CONFIG_PLB2800_ETHER */ diff --git a/drivers/net/rtl8019.c b/drivers/net/rtl8019.c index 9d62cab..3ddf917 100644 --- a/drivers/net/rtl8019.c +++ b/drivers/net/rtl8019.c @@ -32,10 +32,6 @@ #include "rtl8019.h" #include -#ifdef CONFIG_DRIVER_RTL8019 - -#if defined(CONFIG_CMD_NET) - /* packet page register access functions */ static unsigned char get_reg (unsigned int regno) @@ -271,7 +267,3 @@ extern int eth_send (volatile void *packet, int length) return 0; } - -#endif /* CONFIG_CMD_NET */ - -#endif /* CONFIG_DRIVER_RTL8019 */ diff --git a/drivers/net/rtl8139.c b/drivers/net/rtl8139.c index 097f684..4fd20ac 100644 --- a/drivers/net/rtl8139.c +++ b/drivers/net/rtl8139.c @@ -77,9 +77,6 @@ #include #include -#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) && \ - defined(CONFIG_RTL8139) - #define RTL_TIMEOUT 100000 #define ETH_FRAME_LEN 1514 @@ -545,4 +542,3 @@ static void rtl_disable(struct eth_device *dev) udelay (100); /* wait 100us */ } } -#endif diff --git a/drivers/net/rtl8169.c b/drivers/net/rtl8169.c index 6c4c9ff..7423bc0 100644 --- a/drivers/net/rtl8169.c +++ b/drivers/net/rtl8169.c @@ -58,9 +58,6 @@ #include #include -#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) && \ - defined(CONFIG_RTL8169) - #undef DEBUG_RTL8169 #undef DEBUG_RTL8169_TX #undef DEBUG_RTL8169_RX @@ -887,5 +884,3 @@ int rtl8169_initialize(bd_t *bis) } return card_number; } - -#endif diff --git a/drivers/net/s3c4510b_eth.c b/drivers/net/s3c4510b_eth.c index 3d9066a..6dcb244 100644 --- a/drivers/net/s3c4510b_eth.c +++ b/drivers/net/s3c4510b_eth.c @@ -25,9 +25,6 @@ */ #include - -#ifdef CONFIG_DRIVER_S3C4510_ETH - #include #include #include @@ -242,5 +239,3 @@ void eth_halt(void) /* disable MAC */ PUT_REG( REG_MACCON, ETH_HaltReg); } - -#endif diff --git a/drivers/net/smc91111.c b/drivers/net/smc91111.c index 8061f12..e8b235b 100644 --- a/drivers/net/smc91111.c +++ b/drivers/net/smc91111.c @@ -65,8 +65,6 @@ #include "smc91111.h" #include -#ifdef CONFIG_DRIVER_SMC91111 - /* Use power-down feature of the chip */ #define POWER_DOWN 0 @@ -1620,4 +1618,3 @@ int get_rom_mac (uchar *v_rom_mac) return (valid_mac ? 1 : 0); #endif } -#endif /* CONFIG_DRIVER_SMC91111 */ diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 6d93bf0..7555cb9 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -23,9 +23,6 @@ */ #include - -#ifdef CONFIG_DRIVER_SMC911X - #include #include #include @@ -699,5 +696,3 @@ int eth_rx(void) return 0; } - -#endif /* CONFIG_DRIVER_SMC911X */ diff --git a/drivers/net/tigon3.c b/drivers/net/tigon3.c index 5f6a4ec..ab448b0 100644 --- a/drivers/net/tigon3.c +++ b/drivers/net/tigon3.c @@ -12,8 +12,7 @@ /******************************************************************************/ #include #include -#if defined(CONFIG_CMD_NET) && !defined(CONFIG_NET_MULTI) && \ - defined(CONFIG_TIGON3) + #ifdef CONFIG_BMW #include #endif @@ -5695,5 +5694,3 @@ LM_DmaTest (PLM_DEVICE_BLOCK pDevice, PLM_UINT8 pBufferVirt, } return LM_STATUS_SUCCESS; } - -#endif diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c index 397ae71..6e0f2c6 100644 --- a/drivers/net/tsec.c +++ b/drivers/net/tsec.c @@ -17,7 +17,6 @@ #include #include -#if defined(CONFIG_TSEC_ENET) #include "tsec.h" #include "miiphy.h" @@ -1741,5 +1740,3 @@ tsec_mcast_addr (struct eth_device *dev, u8 mcast_mac, u8 set) return 0; } #endif /* Multicast TFTP ? */ - -#endif /* CONFIG_TSEC_ENET */ diff --git a/drivers/net/tsi108_eth.c b/drivers/net/tsi108_eth.c index a09115e..57c0dc3 100644 --- a/drivers/net/tsi108_eth.c +++ b/drivers/net/tsi108_eth.c @@ -27,9 +27,6 @@ #include -#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) \ - && defined(CONFIG_TSI108_ETH) - #if !defined(CONFIG_TSI108_ETH_NUM_PORTS) || (CONFIG_TSI108_ETH_NUM_PORTS > 2) #error "CONFIG_TSI108_ETH_NUM_PORTS must be defined as 1 or 2" #endif @@ -1032,5 +1029,3 @@ static void tsi108_eth_halt (struct eth_device *dev) /* Put MAC into reset state. */ reg_MAC_CONFIG_1(base) = MAC_CONFIG_1_SOFT_RESET; } - -#endif diff --git a/drivers/net/uli526x.c b/drivers/net/uli526x.c index 79d29ae..7145b72 100644 --- a/drivers/net/uli526x.c +++ b/drivers/net/uli526x.c @@ -22,9 +22,6 @@ /* some kernel function compatible define */ -#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) && \ - defined(CONFIG_ULI526X) - #undef DEBUG /* Board/System/Debug information/definition */ @@ -993,4 +990,3 @@ static void set_mac_addr(struct eth_device *dev) udelay(10); return; } -#endif diff --git a/drivers/net/vsc7385.c b/drivers/net/vsc7385.c index 4095bce..4e7259f 100644 --- a/drivers/net/vsc7385.c +++ b/drivers/net/vsc7385.c @@ -13,9 +13,6 @@ */ #include - -#ifdef CONFIG_VSC7385_ENET - #include #include #include @@ -97,5 +94,3 @@ int vsc7385_upload_firmware(void *firmware, unsigned int size) return 0; } - -#endif -- cgit v1.1