From 73646217186aa17afc8e305c5f06f06dd335eaad Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Tue, 20 Nov 2007 20:33:09 +0100 Subject: drivers/pcmcia : move pcmcia drivers to drivers/pcmcia Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD --- drivers/pcmcia/tqm8xx_pcmcia.c | 330 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 330 insertions(+) create mode 100644 drivers/pcmcia/tqm8xx_pcmcia.c (limited to 'drivers/pcmcia/tqm8xx_pcmcia.c') diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c new file mode 100644 index 0000000..132c7a5 --- /dev/null +++ b/drivers/pcmcia/tqm8xx_pcmcia.c @@ -0,0 +1,330 @@ +/* -------------------------------------------------------------------- */ +/* TQM8xxL Boards by TQ Components */ +/* SC8xx Boards by SinoVee Microsystems */ +/* -------------------------------------------------------------------- */ +#include +#ifdef CONFIG_8xx +#include +#endif +#include + +#undef CONFIG_PCMCIA + +#if defined(CONFIG_CMD_PCMCIA) +#define CONFIG_PCMCIA +#endif + +#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD) +#define CONFIG_PCMCIA +#endif + +#if defined(CONFIG_PCMCIA) \ + && (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)) + +#if defined(CONFIG_VIRTLAB2) +#define PCMCIA_BOARD_MSG "Virtlab2" +#elif defined(CONFIG_TQM8xxL) +#define PCMCIA_BOARD_MSG "TQM8xxL" +#elif defined(CONFIG_SVM_SC8xx) +#define PCMCIA_BOARD_MSG "SC8xx" +#endif + +#if defined(CONFIG_NSCU) + +#define power_config(slot) do {} while (0) +#define power_off(slot) do {} while (0) +#define power_on_5_0(slot) do {} while (0) +#define power_on_3_3(slot) do {} while (0) + +#elif defined(CONFIG_HMI10) + +static inline void power_config(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + /* + * Configure Port B pins for + * 5 Volts Enable and 3 Volts enable + */ + immap->im_cpm.cp_pbpar &= ~(0x00000300); +} + +static inline void power_off(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + /* remove all power */ + immap->im_cpm.cp_pbdat |= 0x00000300; +} + +static inline void power_on_5_0(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + immap->im_cpm.cp_pbdat &= ~(0x0000100); + immap->im_cpm.cp_pbdir |= 0x00000300; +} + +static inline void power_on_3_3(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + immap->im_cpm.cp_pbdat &= ~(0x0000200); + immap->im_cpm.cp_pbdir |= 0x00000300; +} + +#elif defined(CONFIG_VIRTLAB2) + +#define power_config(slot) do {} while (0) +static inline void power_off(int slot) +{ + volatile unsigned char *powerctl = + (volatile unsigned char *)PCMCIA_CTRL; + *powerctl = 0; +} + +static inline void power_on_5_0(int slot) +{ + volatile unsigned char *powerctl = + (volatile unsigned char *)PCMCIA_CTRL; + *powerctl = 2; /* Enable 5V Vccout */ +} + +static inline void power_on_3_3(int slot) +{ + volatile unsigned char *powerctl = + (volatile unsigned char *)PCMCIA_CTRL; + *powerctl = 1; /* Enable 3.3V Vccout */ +} + +#else + +static inline void power_config(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + /* + * Configure Port C pins for + * 5 Volts Enable and 3 Volts enable + */ + immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004); + immap->im_ioport.iop_pcso &= ~(0x0002 | 0x0004); +} + +static inline void power_off(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004); +} + +static inline void power_on_5_0(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + immap->im_ioport.iop_pcdat |= 0x0004; + immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004); +} + +static inline void power_on_3_3(int slot) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + immap->im_ioport.iop_pcdat |= 0x0002; + immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004); +} + +#endif + +#ifdef CONFIG_HMI10 +static inline int check_card_is_absent(int slot) +{ + volatile pcmconf8xx_t *pcmp = + (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + return pcmp->pcmc_pipr & (0x10000000 >> (slot << 4)); +} +#else +static inline int check_card_is_absent(int slot) +{ + volatile pcmconf8xx_t *pcmp = + (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + return pcmp->pcmc_pipr & (0x18000000 >> (slot << 4)); +} +#endif + +#ifdef NSCU_OE_INV +#define NSCU_GCRX_CXOE 0 +#else +#define NSCU_GCRX_CXOE __MY_PCMCIA_GCRX_CXOE +#endif + +int pcmcia_hardware_enable(int slot) +{ + volatile pcmconf8xx_t *pcmp = + (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + volatile sysconf8xx_t *sysp = + (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf)); + uint reg, mask; + + debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + udelay(10000); + + /* + * Configure SIUMCR to enable PCMCIA port B + * (VFLS[0:1] are not used for debugging, we connect FRZ# instead) + */ + sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */ + + /* clear interrupt state, and disable interrupts */ + pcmp->pcmc_pscr = PCMCIA_MASK(slot); + pcmp->pcmc_per &= ~PCMCIA_MASK(slot); + + /* + * Disable interrupts, DMA, and PCMCIA buffers + * (isolate the interface) and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= NSCU_GCRX_CXOE; + + PCMCIA_PGCRX(slot) = reg; + udelay(500); + + power_config(slot); + power_off(slot); + + /* + * Make sure there is a card in the slot, then configure the interface. + */ + udelay(10000); + debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__, + &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); + + if (check_card_is_absent(slot)) { + printf (" No Card found\n"); + return (1); + } + + /* + * Power On. + */ + mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot); + reg = pcmp->pcmc_pipr; + debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", + reg, + (reg&PCMCIA_VS1(slot))?"n":"ff", + (reg&PCMCIA_VS2(slot))?"n":"ff"); + + if ((reg & mask) == mask) { + power_on_5_0(slot); + puts (" 5.0V card found: "); + } else { + power_on_3_3(slot); + puts (" 3.3V card found: "); + } + +#if 0 + /* VCC switch error flag, PCMCIA slot INPACK_ pin */ + cp->cp_pbdir &= ~(0x0020 | 0x0010); + cp->cp_pbpar &= ~(0x0020 | 0x0010); + udelay(500000); +#endif + + udelay(1000); + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(slot); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + reg &= ~NSCU_GCRX_CXOE; + + PCMCIA_PGCRX(slot) = reg; + + udelay(250000); /* some cards need >150 ms to come up :-( */ + + debug ("# hardware_enable done\n"); + + return (0); +} + + +#if defined(CONFIG_CMD_PCMCIA) +int pcmcia_hardware_disable(int slot) +{ + u_long reg; + + debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + + /* remove all power */ + power_off(slot); + + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= NSCU_GCRX_CXOE; /* active low */ + + PCMCIA_PGCRX(slot) = reg; + + udelay(10000); + + return (0); +} +#endif + +int pcmcia_voltage_set(int slot, int vcc, int vpp) +{ +#ifndef CONFIG_NSCU + u_long reg; +# ifdef DEBUG + volatile pcmconf8xx_t *pcmp = + (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); +# endif + + debug ("voltage_set: " PCMCIA_BOARD_MSG + " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n", + 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10); + + /* + * Disable PCMCIA buffers (isolate the interface) + * and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = PCMCIA_PGCRX(slot); + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + reg |= NSCU_GCRX_CXOE; /* active low */ + + PCMCIA_PGCRX(slot) = reg; + udelay(500); + + debug ("PCMCIA power OFF\n"); + power_config(slot); + power_off(slot); + + switch(vcc) { + case 0: break; + case 33: power_on_3_3(slot); break; + case 50: power_on_5_0(slot); break; + default: goto done; + } + + /* Checking supported voltages */ + + debug("PIPR: 0x%x --> %s\n", pcmp->pcmc_pipr, + (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V"); + + if (vcc) + debug("PCMCIA powered at %sV\n", (vcc == 50) ? "5.0" : "3.3"); + else + debug("PCMCIA powered down\n"); + +done: + debug("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(slot); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + reg &= ~NSCU_GCRX_CXOE; /* active low */ + + PCMCIA_PGCRX(slot) = reg; + udelay(500); + + debug("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A'); +#endif /* CONFIG_NSCU */ + return (0); +} + +#endif /* CONFIG_PCMCIA && (CONFIG_TQM8xxL || CONFIG_SVM_SC8xx) */ -- cgit v1.1