From f6f5f709e5c8e4564c4dfeecfdf2279244f9c83b Mon Sep 17 00:00:00 2001 From: Joakim Tjernlund Date: Wed, 31 Jan 2007 11:04:19 +0100 Subject: mpc83xx: Fix empty i2c reads/writes in fsl_i2c.c Fix empty i2c reads/writes, i2c_write(0x50, 0x00, 0, NULL, 0) which is used to se if an slave will ACK after receiving its address. Correct i2c probing to use this method as the old method could upset a slave as it wrote a data byte to it. Add a small delay in i2c_init() to let the controller shutdown any ongoing I2C activity. Signed-off-by: Joakim Tjernlund --- drivers/fsl_i2c.c | 27 ++++++++++++++------------- 1 file changed, 14 insertions(+), 13 deletions(-) (limited to 'drivers/fsl_i2c.c') diff --git a/drivers/fsl_i2c.c b/drivers/fsl_i2c.c index c929096..ebae5af 100644 --- a/drivers/fsl_i2c.c +++ b/drivers/fsl_i2c.c @@ -58,6 +58,7 @@ i2c_init(int speed, int slaveadd) dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET); writeb(0, &dev->cr); /* stop I2C controller */ + udelay(5); /* let it shutdown in peace */ writeb(0x3F, &dev->fdr); /* set bus speed */ writeb(0x3F, &dev->dfsrr); /* set default filter */ writeb(slaveadd << 1, &dev->adr); /* write slave address */ @@ -191,15 +192,17 @@ __i2c_read(u8 *data, int length) int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) { - int i = 0; + int i = -1; /* signal error */ u8 *a = (u8*)&addr; if (i2c_wait4bus() >= 0 && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 - && __i2c_write(&a[4 - alen], alen) == alen - && i2c_write_addr(dev, I2C_READ_BIT, 1) != 0) { + && __i2c_write(&a[4 - alen], alen) == alen) + i = 0; /* No error so far */ + + if (length + && i2c_write_addr(dev, I2C_READ_BIT, 1) != 0) i = __i2c_read(data, length); - } writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); @@ -212,7 +215,7 @@ i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) { - int i = 0; + int i = -1; /* signal error */ u8 *a = (u8*)&addr; if (i2c_wait4bus() >= 0 @@ -232,16 +235,14 @@ i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) int i2c_probe(uchar chip) { - int tmp; - - /* - * Try to read the first location of the chip. The underlying - * driver doesn't appear to support sending just the chip address - * and looking for an back. + /* For unknow reason the controller will ACK when + * probing for a slave with the same address, so skip + * it. */ - udelay(10000); + if (chip == (readb(&i2c_dev[i2c_bus_num]->adr) >> 1)) + return -1; - return i2c_read(chip, 0, 1, (uchar *)&tmp, 1); + return i2c_read(chip, 0, 0, NULL, 0); } uchar -- cgit v1.1