From 3e38691e8f7aa0d9b498d76c7279ddec6e4946f3 Mon Sep 17 00:00:00 2001 From: wdenk Date: Sat, 5 Apr 2003 00:53:31 +0000 Subject: * Patch by Arun Dharankar, 4 Apr 2003: Add IDMA example code (tested on 8260 only) * Add support for Purple Board (MIPS64 5Kc) * Add support for MIPS64 5Kc CPUs * Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS * Patch by Denis Peter, 04 Apr 2003: - update MIP405-4 board * Patches by Denis Peter, 03 April 2003: - fix PCI IRQs on MPL boards - fix two more un-relocated pointer problems * Fix behaviour of "run" command: - print error message iv variable does not exist - terminate processing of arguments in case of error * Patches by Peter Figuli, 10 Mar 2003 - Add support for BTUART on PXA platform - Add support for WEP EP250 (PXA) board * Fix flash problems on INCA-IP; add tool to allow bruning images to flash using a BDI2000 * Implement fix for I2C Edge Conditions problem for all boards that use the bit-banging driver (common/soft_i2c.c) * Add patches by Robert Schwebel, 31 Mar 2003: - csb226 board: bring in sync with innokom/memsetup.S - csb226 board: fix MDREFR handling - misc doc fixes / extensions - innokom board: cleanup, MDREFR fix in memsetup.S, config update - add BOOT_PROGRESS to armlinux.c --- doc/README.INCA-IP | 44 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 44 insertions(+) create mode 100644 doc/README.INCA-IP (limited to 'doc/README.INCA-IP') diff --git a/doc/README.INCA-IP b/doc/README.INCA-IP new file mode 100644 index 0000000..517eec0 --- /dev/null +++ b/doc/README.INCA-IP @@ -0,0 +1,44 @@ + +Flash programming on the INCA-IP board is complicated because of the +EBU swapping unit. A BDI2000 can be used for flash programming only +if the EBU swapping unit is enabled; otherwise it will not detect the +flash memory. But the EBU swapping unit is disadbled after reset, so +if you program some code to flash with the swapping unit on, it will +not be runnable with the swapping unit off. + +The consequence is that you have to write a pre-swapped image to +flash using the BDI2000. A simple host-side tool "inca-swap-bytes" is +provided in the "tools/" directory. Use it as follows: + + bash$ ./inca-swap-bytes u-boot.bin.swp + +Note that the current BDI config file _disables_ the EBU swapping +unit for the flash bank 0. To enable it, (this is required for the +BDI flash commands to work) uncomment the following line in the +config file: + + ;WM32 0xb8000260 0x404161ff ; Swapping unit enabled + +and comment out + + WM32 0xb8000260 0x004161ff ; Swapping unit disabled + +Alternatively, you can use "mm 0xb8000260 " commands to +enable/disable the swapping unit manually. + +Just for reference, here is the complete sequence of actions we took +to install a U-Boot image into flash. + + 1. ./inca-swap-bytes u-boot.bin.swp + + 2. From BDI: + + mm 0xb8000260 0x404161ff + erase 0xb0000000 + erase 0xb0010000 + prog 0xb0000000 /tftpboot/INCA/u-boot.bin.swp bin + mm 0xb8000260 0x004161ff + go 0xb0000000 + + +(C) 2003 Wolfgang Denk -- cgit v1.1