From 373ee048a8bdc3291aa88b93da183a0bc3b34a22 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:04:58 +0100 Subject: ARM: IXP: Remove actux1 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux1/Makefile | 8 --- board/actux1/actux1.c | 148 ----------------------------------------------- board/actux1/actux1_hw.h | 41 ------------- board/actux1/u-boot.lds | 99 ------------------------------- 4 files changed, 296 deletions(-) delete mode 100644 board/actux1/Makefile delete mode 100644 board/actux1/actux1.c delete mode 100644 board/actux1/actux1_hw.h delete mode 100644 board/actux1/u-boot.lds (limited to 'board') diff --git a/board/actux1/Makefile b/board/actux1/Makefile deleted file mode 100644 index 05a8669..0000000 --- a/board/actux1/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux1.o diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c deleted file mode 100644 index 03ccd93..0000000 --- a/board/actux1/actux1.c +++ /dev/null @@ -1,148 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#ifdef CONFIG_PCI -#include -#include -#endif - -#include "actux1_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: HwRel */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - - /* Setup GPIOs for PCI INTA */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA); - - /* Setup GPIOs for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - - ACTUX1_LED1(2); - ACTUX1_LED2(2); - ACTUX1_LED3(0); - ACTUX1_LED4(0); - ACTUX1_LED5(0); - ACTUX1_LED6(0); - ACTUX1_LED7(0); - - ACTUX1_HS(ACTUX1_HS_DCD); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-1 rev."); - putc(ACTUX1_BOARDREL + 'A' - 1); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX1_BOARDREL; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -void reset_phy(void) -{ - u16 id1, id2; - - /* initialize the PHY */ - miiphy_reset("NPE0", CONFIG_PHY_ADDR); - - miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1); - miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2); - - id2 &= 0xFFF0; /* mask out revision bits */ - - if (id1 == 0x13 && id2 == 0x78e0) { - /* - * LXT971/LXT972 PHY: set LED outputs: - * LED1(green) = Link/ACT, - * LED2 (unused) = LINK, - * LED3(red) = Coll - */ - miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432); - } else if (id1 == 0x143 && id2 == 0xbc30) { - /* BCM5241: default values are OK */ - } else - printf("unknown ethernet PHY ID: %x %x\n", id1, id2); -} diff --git a/board/actux1/actux1_hw.h b/board/actux1/actux1_hw.h deleted file mode 100644 index 5627f24..0000000 --- a/board/actux1/actux1_hw.h +++ /dev/null @@ -1,41 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-1 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX1_HW_H -#define _ACTUX1_HW_H - -/* 0 = LED off,1 = green, 2 = red, 3 = orange */ -#define ACTUX1_LED1(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX1_LED2(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX1_LED3(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX1_LED4(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 3) -#define ACTUX1_LED5(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 4) -#define ACTUX1_LED6(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 5) -#define ACTUX1_LED7(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 6) -#define ACTUX1_HS(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7) -#define ACTUX1_HS_DCD 0x01 -#define ACTUX1_HS_DSR 0x02 - -#define ACTUX1_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX1_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) - -/* GPIO settings */ -#define CONFIG_SYS_GPIO_PCI1_INTA 2 -#define CONFIG_SYS_GPIO_PCI2_INTA 3 -#define CONFIG_SYS_GPIO_I2C_SDA 4 -#define CONFIG_SYS_GPIO_I2C_SCL 5 -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds deleted file mode 100644 index 4716e4f..0000000 --- a/board/actux1/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux1/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} -- cgit v1.1 From 13e0ee7f9acf6f1af0db7147ea8d157668f45ca6 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:06:45 +0100 Subject: ARM: IXP: Remove actux2 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux2/Makefile | 8 ---- board/actux2/actux2.c | 122 ----------------------------------------------- board/actux2/actux2_hw.h | 43 ----------------- board/actux2/u-boot.lds | 99 -------------------------------------- 4 files changed, 272 deletions(-) delete mode 100644 board/actux2/Makefile delete mode 100644 board/actux2/actux2.c delete mode 100644 board/actux2/actux2_hw.h delete mode 100644 board/actux2/u-boot.lds (limited to 'board') diff --git a/board/actux2/Makefile b/board/actux2/Makefile deleted file mode 100644 index 24cbff1..0000000 --- a/board/actux2/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux2.o diff --git a/board/actux2/actux2.c b/board/actux2/actux2.c deleted file mode 100644 index e578cd0..0000000 --- a/board/actux2/actux2.c +++ /dev/null @@ -1,122 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -#include - -#include "actux2_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: IPAC-X */ - writel(0x94d10013, IXP425_EXP_CS1); - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: HW release register */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD); - - /* Setup GPIOs for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT); - - /* Setup GPIOs for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST); - - ACTUX2_LED1(1); - ACTUX2_LED2(0); - ACTUX2_LED3(0); - ACTUX2_LED4(0); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-2 rev."); - putc(ACTUX2_BOARDREL + 'A' - 1); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX2_BOARDREL; -} - -void reset_phy(void) -{ - /* init IcPlus IP175C ethernet switch to native IP175C mode */ - miiphy_write("NPE0", 29, 31, 0x175C); -} diff --git a/board/actux2/actux2_hw.h b/board/actux2/actux2_hw.h deleted file mode 100644 index 57c6fa7..0000000 --- a/board/actux2/actux2_hw.h +++ /dev/null @@ -1,43 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-2 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX2_HW_H -#define _ACTUX2_HW_H - -/* 0 = LED off,1 = green, 2 = red, 3 = orange */ -#define ACTUX2_LED1(a) writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX2_LED2(a) writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX2_LED3(a) writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX2_LED4(a) writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 3) - -#define ACTUX2_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX2_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) -#define ACTUX2_OPTION (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0) - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_DBGINT 0 -#define CONFIG_SYS_GPIO_ETHINT 1 -#define CONFIG_SYS_GPIO_ETHRST 2 /* Out */ -#define CONFIG_SYS_GPIO_LED5_GN 3 /* Out */ -#define CONFIG_SYS_GPIO_UNUSED4 4 -#define CONFIG_SYS_GPIO_UNUSED5 5 -#define CONFIG_SYS_GPIO_DSR 6 /* Out */ -#define CONFIG_SYS_GPIO_DCD 7 /* Out */ -#define CONFIG_SYS_GPIO_IPAC_INT 8 -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux2/u-boot.lds b/board/actux2/u-boot.lds deleted file mode 100644 index f00d7c7..0000000 --- a/board/actux2/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux2/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} -- cgit v1.1 From 38da33f3c1fabeb0350c1bd0ed28556802cc7c12 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:08:10 +0100 Subject: ARM: IXP: Remove actux3 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux3/Makefile | 8 --- board/actux3/actux3.c | 149 ----------------------------------------------- board/actux3/actux3_hw.h | 44 -------------- board/actux3/u-boot.lds | 99 ------------------------------- 4 files changed, 300 deletions(-) delete mode 100644 board/actux3/Makefile delete mode 100644 board/actux3/actux3.c delete mode 100644 board/actux3/actux3_hw.h delete mode 100644 board/actux3/u-boot.lds (limited to 'board') diff --git a/board/actux3/Makefile b/board/actux3/Makefile deleted file mode 100644 index f628f26..0000000 --- a/board/actux3/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux3.o diff --git a/board/actux3/actux3.c b/board/actux3/actux3.c deleted file mode 100644 index 09c803c..0000000 --- a/board/actux3/actux3.c +++ /dev/null @@ -1,149 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include "actux3_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: IPAC-X */ - writel(0x94d10013, IXP425_EXP_CS1); - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: Release/Option register */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED5_GN); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_RT); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_GN); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED5_GN); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_RT); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_GN); - - /* - * Setup GPIO's for Interrupt inputs - */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT); - - /* - * Setup GPIO's for 33MHz clock output - */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - /* we need a minimum PCI reset pulse width after enabling the clock */ - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST); - - ACTUX3_LED1_RT(1); - ACTUX3_LED1_GN(0); - ACTUX3_LED2_RT(0); - ACTUX3_LED2_GN(0); - ACTUX3_LED3_RT(0); - ACTUX3_LED3_GN(0); - ACTUX3_LED4_GN(0); - ACTUX3_LED5_RT(0); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-3 rev."); - putc(ACTUX3_BOARDREL + 'A' - 1); - - if (i > 0) { - puts (", serial# "); - puts (buf); - } - putc('\n'); - - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX3_BOARDREL; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -void reset_phy(void) -{ - int i; - - /* initialize the PHY */ - miiphy_reset("NPE0", CONFIG_PHY_ADDR); - - /* all LED outputs = Link/Act */ - miiphy_write("NPE0", CONFIG_PHY_ADDR, 0x16, 0x0AAA); - - /* - * The Marvell 88E6060 switch comes up with all ports disabled. - * set all ethernet switch ports to forwarding state - */ - for (i = 1; i <= 5; i++) - miiphy_write("NPE0", CONFIG_PHY_ADDR + 8 + i, 0x04, 0x03); - -} diff --git a/board/actux3/actux3_hw.h b/board/actux3/actux3_hw.h deleted file mode 100644 index f8acb4d..0000000 --- a/board/actux3/actux3_hw.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-3 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX3_HW_H -#define _ACTUX3_HW_H - -/* 0 = LED off,1 = ON */ -#define ACTUX3_LED1_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX3_LED1_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX3_LED2_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX3_LED2_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 3) -#define ACTUX3_LED3_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 4) -#define ACTUX3_LED3_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 5) -#define ACTUX3_LED4_GN(a) writeb((a)^1, IXP425_EXP_BUS_CS7_BASE_PHYS + 6) -#define ACTUX3_LED5_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7) - -#define ACTUX3_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX3_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) -#define ACTUX3_OPTION (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0) - -/* GPIO settings */ -#define CONFIG_SYS_GPIO_DBGINT 0 -#define CONFIG_SYS_GPIO_ETHINT 1 -#define CONFIG_SYS_GPIO_ETHRST 2 /* Out */ -#define CONFIG_SYS_GPIO_LED5_GN 3 /* Out */ -#define CONFIG_SYS_GPIO_LED6_RT 4 /* Out */ -#define CONFIG_SYS_GPIO_LED6_GN 5 /* Out */ -#define CONFIG_SYS_GPIO_DSR 6 /* Out */ -#define CONFIG_SYS_GPIO_DCD 7 /* Out */ -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux3/u-boot.lds b/board/actux3/u-boot.lds deleted file mode 100644 index 2de3ca6..0000000 --- a/board/actux3/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux3/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} -- cgit v1.1 From 6ff7aafa4b1f3a3f3808c9a9d9257f13e880689b Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:09:01 +0100 Subject: ARM: IXP: Remove actux4 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux4/Makefile | 8 --- board/actux4/actux4.c | 129 ----------------------------------------------- board/actux4/actux4_hw.h | 33 ------------ 3 files changed, 170 deletions(-) delete mode 100644 board/actux4/Makefile delete mode 100644 board/actux4/actux4.c delete mode 100644 board/actux4/actux4_hw.h (limited to 'board') diff --git a/board/actux4/Makefile b/board/actux4/Makefile deleted file mode 100644 index b949b60..0000000 --- a/board/actux4/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux4.o diff --git a/board/actux4/actux4.c b/board/actux4/actux4.c deleted file mode 100644 index 81c5458..0000000 --- a/board/actux4/actux4.c +++ /dev/null @@ -1,129 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#ifdef CONFIG_PCI -#include -#include -#endif - -#include "actux4_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - writel(0xbd113c42, IXP425_EXP_CS1); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_nPWRON); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_nPWRON); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - - /* led not populated on board*/ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED3); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED3); - - /* middle LED */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED2); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED2); - - /* right LED */ - /* weak pulldown = LED weak on */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_LED1); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED1); - - /* Setup GPIO's for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTB); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTC); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RTCINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB); - - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTB); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTC); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RTCINT); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB); - - /* Setup GPIO's for 33MHz clock output */ - writel(0x011001FF, IXP425_GPIO_GPCLKR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - - udelay(10000); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - udelay(10000); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - udelay(10000); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - - return 0; -} - -/* Check Board Identity */ -int checkboard(void) -{ - puts("Board: AcTux-4\n"); - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -/* - * Hardcoded flash setup: - * Flash 0 is a non-CFI SST 39VF020 flash, 8 bit flash / 8 bit bus. - * Flash 1 is an Intel *16 flash using the CFI driver. - */ -ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info) -{ - if (banknum == 0) { /* non-CFI boot flash */ - info->portwidth = 1; - info->chipwidth = 1; - info->interface = FLASH_CFI_X8; - return 1; - } else - return 0; -} diff --git a/board/actux4/actux4_hw.h b/board/actux4/actux4_hw.h deleted file mode 100644 index b936376..0000000 --- a/board/actux4/actux4_hw.h +++ /dev/null @@ -1,33 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-4 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX4_HW_H -#define _ACTUX4_HW_H - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_USBINTA 0 -#define CONFIG_SYS_GPIO_USBINTB 1 -#define CONFIG_SYS_GPIO_USBINTC 2 -#define CONFIG_SYS_GPIO_nPWRON 3 /* Out */ -#define CONFIG_SYS_GPIO_I2C_SCL 4 -#define CONFIG_SYS_GPIO_I2C_SDA 5 -#define CONFIG_SYS_GPIO_PCI_INTB 6 -#define CONFIG_SYS_GPIO_BUTTON1 7 -#define CONFIG_SYS_GPIO_LED1 8 /* Out */ -#define CONFIG_SYS_GPIO_RTCINT 9 -#define CONFIG_SYS_GPIO_LED2 10 /* Out */ -#define CONFIG_SYS_GPIO_PCI_INTA 11 -#define CONFIG_SYS_GPIO_IORST 12 /* Out */ -#define CONFIG_SYS_GPIO_LED3 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif -- cgit v1.1 From e317de6b083adee81187fe1bba8b2fdf0ac983e7 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:10:46 +0100 Subject: ARM: IXP: Remove dvl_host board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/dvlhost/Makefile | 8 ---- board/dvlhost/dvlhost.c | 112 --------------------------------------------- board/dvlhost/dvlhost_hw.h | 31 ------------- board/dvlhost/u-boot.lds | 99 --------------------------------------- board/dvlhost/watchdog.c | 27 ----------- 5 files changed, 277 deletions(-) delete mode 100644 board/dvlhost/Makefile delete mode 100644 board/dvlhost/dvlhost.c delete mode 100644 board/dvlhost/dvlhost_hw.h delete mode 100644 board/dvlhost/u-boot.lds delete mode 100644 board/dvlhost/watchdog.c (limited to 'board') diff --git a/board/dvlhost/Makefile b/board/dvlhost/Makefile deleted file mode 100644 index 8b48936..0000000 --- a/board/dvlhost/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := dvlhost.o watchdog.o diff --git a/board/dvlhost/dvlhost.c b/board/dvlhost/dvlhost.c deleted file mode 100644 index 087070f..0000000 --- a/board/dvlhost/dvlhost.c +++ /dev/null @@ -1,112 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include -#ifdef CONFIG_PCI -#include -#include -#endif - -#include "dvlhost_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: LED Latch */ - writel(0xBFFF0002, IXP425_EXP_CS1); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - /* Setup GPIOs used as output */ - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDGTRIGGER); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DLAN_PAIRING); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PCIRST); - - /* - * LED latch enable and watchdog enable are tied to the same GPIO, - * so we need to trigger the watchdog if we want to enable the LEDs. - */ -#ifdef CONFIG_HW_WATCHDOG - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDG_LED_EN); -#else - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_WDG_LED_EN); -#endif - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDGTRIGGER); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DLAN_PAIRING); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDG_LED_EN); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCIRST); - - /* Setup GPIOs for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_WLAN); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_PAIRING); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_RESET); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQB); - - /* Setup GPIO's for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x01FF01FF, IXP425_GPIO_GPCLKR); - - /* turn off all LEDs */ - writew(0x0000, DVLHOST_LED_LATCH); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_PCIRST); - - return 0; -} - -/* Check Board Identity */ -int checkboard(void) -{ - char *s = getenv("serial#"); - - puts("Board: dLAN 200AV (dvlhost)"); - - if (s != NULL) { - puts(", serial# "); - puts(s); - } - putc('\n'); - - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -void reset_phy(void) -{ - /* init IcPlus IP175C ethernet switch to native IP175C mode */ - miiphy_write("NPE1", 29, 31, 0x175C); -} diff --git a/board/dvlhost/dvlhost_hw.h b/board/dvlhost/dvlhost_hw.h deleted file mode 100644 index 545099e..0000000 --- a/board/dvlhost/dvlhost_hw.h +++ /dev/null @@ -1,31 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the - * dLAN200 AV Wireless G ("dvlhost") board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _DVLHOST_HW_H -#define _DVLHOST_HW_H - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_WDGTRIGGER 0 /* Out */ -#define CONFIG_SYS_GPIO_BTN_WLAN 1 -#define CONFIG_SYS_GPIO_BTN_PAIRING 6 -#define CONFIG_SYS_GPIO_DLAN_PAIRING 7 /* Out */ -#define CONFIG_SYS_GPIO_BTN_RESET 9 -#define CONFIG_SYS_GPIO_IRQB 10 -#define CONFIG_SYS_GPIO_IRQA 11 -#define CONFIG_SYS_GPIO_WDG_LED_EN 12 /* Out */ -#define CONFIG_SYS_GPIO_PCIRST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#define DVLHOST_LED_LATCH IXP425_EXP_BUS_CS1_BASE_PHYS - -#endif diff --git a/board/dvlhost/u-boot.lds b/board/dvlhost/u-boot.lds deleted file mode 100644 index ebcaf44..0000000 --- a/board/dvlhost/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/dvlhost/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/serial/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN (4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN (4); - .data : { - *(.data*) - } - . = ALIGN (4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/board/dvlhost/watchdog.c b/board/dvlhost/watchdog.c deleted file mode 100644 index 02ec35e..0000000 --- a/board/dvlhost/watchdog.c +++ /dev/null @@ -1,27 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include "dvlhost_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_HW_WATCHDOG -#include -#include - -void hw_watchdog_reset(void) -{ - unsigned int x; - x = readl(IXP425_GPIO_GPOUTR); - x ^= (1 << (CONFIG_SYS_GPIO_WDGTRIGGER)); - writel(x, IXP425_GPIO_GPOUTR); -} - -#endif /* CONFIG_HW_WATCHDOG */ -- cgit v1.1