From e3150c77617c7d452420e6c87769b79b6671b12d Mon Sep 17 00:00:00 2001 From: Asen Dimov Date: Tue, 6 Apr 2010 16:18:04 +0300 Subject: pm9261 converted to at91 soc access Signed-off-by: Asen Dimov --- board/ronetix/pm9261/led.c | 18 ++--- board/ronetix/pm9261/pm9261.c | 152 ++++++++++++++++++++++++------------------ 2 files changed, 97 insertions(+), 73 deletions(-) (limited to 'board') diff --git a/board/ronetix/pm9261/led.c b/board/ronetix/pm9261/led.c index 396c3e7..ff21ce6 100644 --- a/board/ronetix/pm9261/led.c +++ b/board/ronetix/pm9261/led.c @@ -26,19 +26,21 @@ #include #include #include -#include +#include #include void coloured_LED_init(void) { + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + /* Enable clock */ - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_PIOC); + writel(1 << AT91SAM9261_ID_PIOC, &pmc->pcer); - at91_set_gpio_output(CONFIG_RED_LED, 1); - at91_set_gpio_output(CONFIG_GREEN_LED, 1); - at91_set_gpio_output(CONFIG_YELLOW_LED, 1); + at91_set_pio_output(CONFIG_RED_LED, 1); + at91_set_pio_output(CONFIG_GREEN_LED, 1); + at91_set_pio_output(CONFIG_YELLOW_LED, 1); - at91_set_gpio_value(CONFIG_RED_LED, 0); - at91_set_gpio_value(CONFIG_GREEN_LED, 1); - at91_set_gpio_value(CONFIG_YELLOW_LED, 1); + at91_set_pio_value(CONFIG_RED_LED, 0); + at91_set_pio_value(CONFIG_GREEN_LED, 1); + at91_set_pio_value(CONFIG_YELLOW_LED, 1); } diff --git a/board/ronetix/pm9261/pm9261.c b/board/ronetix/pm9261/pm9261.c index 8662339..53d8c48 100644 --- a/board/ronetix/pm9261/pm9261.c +++ b/board/ronetix/pm9261/pm9261.c @@ -27,13 +27,14 @@ #include #include #include -#include #include #include #include #include +#include +#include #include -#include +#include #include #include #include @@ -55,39 +56,48 @@ DECLARE_GLOBAL_DATA_PTR; static void pm9261_nand_hw_init(void) { unsigned long csa; + at91_smc_t *smc = (at91_smc_t *) AT91_SMC_BASE; + at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE; + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; /* Enable CS3 */ - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, - csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); + csa = readl(&matrix->csa) | AT91_MATRIX_CSA_EBI_CS3A; + writel(csa, &matrix->csa); /* Configure SMC CS3 for NAND/SmartMedia */ - at91_sys_write(AT91_SMC_SETUP(3), - AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), - AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) | - AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), - AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); - at91_sys_write(AT91_SMC_MODE(3), - AT91_SMC_READMODE | AT91_SMC_WRITEMODE | - AT91_SMC_EXNWMODE_DISABLE | + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); + + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | #ifdef CONFIG_SYS_NAND_DBW_16 - AT91_SMC_DBW_16 | + AT91_SMC_MODE_DBW_16 | #else /* CONFIG_SYS_NAND_DBW_8 */ - AT91_SMC_DBW_8 | + AT91_SMC_MODE_DBW_8 | #endif - AT91_SMC_TDF_(2)); + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); + + writel(1 << AT91SAM9261_ID_PIOA | + 1 << AT91SAM9261_ID_PIOC, + &pmc->pcer); /* Configure RDY/BSY */ - at91_set_gpio_input(AT91_PIN_PA16, 1); + at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1); /* Enable NandFlash */ - at91_set_gpio_output(AT91_PIN_PC14, 1); + at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); - at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */ - at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */ + at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* NANDOE */ + at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* NANDWE */ } #endif @@ -95,23 +105,30 @@ static void pm9261_nand_hw_init(void) #ifdef CONFIG_DRIVER_DM9000 static void pm9261_dm9000_hw_init(void) { + at91_smc_t *smc = (at91_smc_t *) AT91_SMC_BASE; + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + /* Configure SMC CS2 for DM9000 */ - at91_sys_write(AT91_SMC_SETUP(2), - AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(2), - AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | - AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8)); - at91_sys_write(AT91_SMC_CYCLE(2), - AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16)); - at91_sys_write(AT91_SMC_MODE(2), - AT91_SMC_READMODE | AT91_SMC_WRITEMODE | - AT91_SMC_EXNWMODE_DISABLE | - AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | - AT91_SMC_TDF_(1)); + writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[2].setup); + + writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) | + AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8), + &smc->cs[2].pulse); + + writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16), + &smc->cs[2].cycle); + + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | + AT91_SMC_MODE_TDF_CYCLE(1), + &smc->cs[2].mode); /* Configure Interrupt pin as input, no pull-up */ - at91_set_gpio_input(AT91_PIN_PA24, 0); + writel(1 << AT91SAM9261_ID_PIOA, &pmc->pcer); + at91_set_pio_input(AT91_PIO_PORTA, 24, 0); } #endif @@ -135,40 +152,42 @@ vidinfo_t panel_info = { void lcd_enable(void) { - at91_set_gpio_value(AT91_PIN_PA22, 0); /* power up */ + at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power up */ } void lcd_disable(void) { - at91_set_gpio_value(AT91_PIN_PA22, 1); /* power down */ + at91_set_pio_value(AT91_PIO_PORTA, 22, 1); /* power down */ } static void pm9261_lcd_hw_init(void) { - at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ - at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ - at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ - at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */ - at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */ - at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */ - at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */ - at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */ - at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */ - at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */ - at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */ - at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */ - at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */ - at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */ - at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */ - at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */ - at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */ - at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */ - at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */ - at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */ - at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ - at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ - - at91_sys_write(AT91_PMC_SCER, AT91_PMC_HCK1); + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + + at91_set_a_periph(AT91_PIO_PORTB, 1, 0); /* LCDHSYNC */ + at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* LCDDOTCK */ + at91_set_a_periph(AT91_PIO_PORTB, 3, 0); /* LCDDEN */ + at91_set_a_periph(AT91_PIO_PORTB, 4, 0); /* LCDCC */ + at91_set_a_periph(AT91_PIO_PORTB, 7, 0); /* LCDD2 */ + at91_set_a_periph(AT91_PIO_PORTB, 8, 0); /* LCDD3 */ + at91_set_a_periph(AT91_PIO_PORTB, 9, 0); /* LCDD4 */ + at91_set_a_periph(AT91_PIO_PORTB, 10, 0); /* LCDD5 */ + at91_set_a_periph(AT91_PIO_PORTB, 11, 0); /* LCDD6 */ + at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* LCDD7 */ + at91_set_a_periph(AT91_PIO_PORTB, 15, 0); /* LCDD10 */ + at91_set_a_periph(AT91_PIO_PORTB, 16, 0); /* LCDD11 */ + at91_set_a_periph(AT91_PIO_PORTB, 17, 0); /* LCDD12 */ + at91_set_a_periph(AT91_PIO_PORTB, 18, 0); /* LCDD13 */ + at91_set_a_periph(AT91_PIO_PORTB, 19, 0); /* LCDD14 */ + at91_set_a_periph(AT91_PIO_PORTB, 20, 0); /* LCDD15 */ + at91_set_b_periph(AT91_PIO_PORTB, 23, 0); /* LCDD18 */ + at91_set_b_periph(AT91_PIO_PORTB, 24, 0); /* LCDD19 */ + at91_set_b_periph(AT91_PIO_PORTB, 25, 0); /* LCDD20 */ + at91_set_b_periph(AT91_PIO_PORTB, 26, 0); /* LCDD21 */ + at91_set_b_periph(AT91_PIO_PORTB, 27, 0); /* LCDD22 */ + at91_set_b_periph(AT91_PIO_PORTB, 28, 0); /* LCDD23 */ + + writel(1 << 17, &pmc->scer); /* LCD controller Clock, AT91SAM9261 only */ gd->fb_base = AT91SAM9261_SRAM_BASE; } @@ -222,11 +241,14 @@ void lcd_show_board_info(void) int board_init(void) { + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + /* Enable Ctrlc */ console_init_f(); - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_PIOA); - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_PIOC); + writel(1 << AT91SAM9261_ID_PIOA | + 1 << AT91SAM9261_ID_PIOC, + &pmc->pcer); /* arch number of PM9261-Board */ gd->bd->bi_arch_number = MACH_TYPE_PM9261; -- cgit v1.1 From bbe310922f4d0b12c8aba97b45ed979db9c0ec9a Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 5 Mar 2010 07:36:33 +0100 Subject: arm, i.mx27: add support for magnesium board from projectiondesign This patch adds support for the magnesium board from projectiondesign. This board uses i.MX27 SoC and has 8MB NOR flash, 128MB NAND flash, FEC ethernet controller integrated into i.MX27. As this port is based on the imx27lite port, common config options are collected in include/configs/imx27lite-common.h Signed-off-by: Heiko Schocher --- board/logicpd/imx27lite/imx27lite.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-) (limited to 'board') diff --git a/board/logicpd/imx27lite/imx27lite.c b/board/logicpd/imx27lite/imx27lite.c index 63375d5..4427415 100644 --- a/board/logicpd/imx27lite/imx27lite.c +++ b/board/logicpd/imx27lite/imx27lite.c @@ -29,6 +29,10 @@ DECLARE_GLOBAL_DATA_PTR; int board_init (void) { struct gpio_regs *regs = (struct gpio_regs *)IMX_GPIO_BASE; +#if defined(CONFIG_SYS_NAND_LARGEPAGE) + struct system_control_regs *sc_regs = + (struct system_control_regs *)IMX_SYSTEM_CTL_BASE; +#endif gd->bd->bi_arch_number = MACH_TYPE_IMX27LITE; gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; @@ -43,9 +47,20 @@ int board_init (void) ®s->port[PORTC].dr); #endif #ifdef CONFIG_MXC_MMC +#if defined(CONFIG_MAGNESIUM) + mx27_sd1_init_pins(); +#else mx27_sd2_init_pins(); #endif +#endif +#if defined(CONFIG_SYS_NAND_LARGEPAGE) + /* + * set in FMCR NF_FMS Bit(5) to 1 + * (NAND Flash with 2 Kbyte page size) + */ + writel(readl(&sc_regs->fmcr) | (1 << 5), &sc_regs->fmcr); +#endif return 0; } @@ -68,6 +83,7 @@ int dram_init (void) int checkboard(void) { - printf("LogicPD imx27lite\n"); + puts ("Board: "); + puts(CONFIG_BOARDNAME); return 0; } -- cgit v1.1 From 272017853339f5b9685f9488bdaf5405812d12a4 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 31 Mar 2010 06:32:56 -0700 Subject: MX51EVK: Remove CPLD related code There is no CPLD on MX51EVK board, so remove CPLD related function. Signed-off-by: Fabio Estevam --- board/freescale/mx51evk/mx51evk.c | 67 --------------------------------------- board/freescale/mx51evk/mx51evk.h | 1 - 2 files changed, 68 deletions(-) (limited to 'board') diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 8754563..f0b7abc 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -72,72 +72,6 @@ static void setup_iomux_uart(void) mxc_iomux_set_pad(MX51_PIN_UART1_CTS, pad); } -static void setup_expio(void) -{ - u32 reg; - struct weim *pweim = (struct weim *)WEIM_BASE_ADDR; - struct clkctl *pclkctl = (struct clkctl *)CCM_BASE_ADDR; - - /* CS5 setup */ - mxc_request_iomux(MX51_PIN_EIM_CS5, IOMUX_CONFIG_ALT0); - writel(0x00410089, &pweim[5].csgcr1); - writel(0x00000002, &pweim[5].csgcr2); - - /* RWSC=50, RADVA=2, RADVN=6, OEA=0, OEN=0, RCSA=0, RCSN=0 */ - writel(0x32260000, &pweim[5].csrcr1); - - /* APR = 0 */ - writel(0x00000000, &pweim[5].csrcr2); - - /* - * WAL=0, WBED=1, WWSC=50, WADVA=2, WADVN=6, WEA=0, WEN=0, - * WCSA=0, WCSN=0 - */ - writel(0x72080F00, &pweim[5].cswcr1); - - mx51_io_board = (struct io_board_ctrl *)(CS5_BASE_ADDR + - IO_BOARD_OFFSET); - if ((readw(&mx51_io_board->id1) == 0xAAAA) && - (readw(&mx51_io_board->id2) == 0x5555)) { - if (is_soc_rev(CHIP_REV_2_0) < 0) { - reg = readl(&pclkctl->cbcdr); - reg = (reg & (~0x70000)) | 0x30000; - writel(reg, &pclkctl->cbcdr); - /* make sure divider effective */ - while (readl(&pclkctl->cdhipr) != 0) - ; - writel(0x0, &pclkctl->ccdr); - } - } else { - /* CS1 */ - writel(0x00410089, &pweim[1].csgcr1); - writel(0x00000002, &pweim[1].csgcr2); - /* RWSC=50, RADVA=2, RADVN=6, OEA=0, OEN=0, RCSA=0, RCSN=0 */ - writel(0x32260000, &pweim[1].csrcr1); - /* APR=0 */ - writel(0x00000000, &pweim[1].csrcr2); - /* - * WAL=0, WBED=1, WWSC=50, WADVA=2, WADVN=6, WEA=0, - * WEN=0, WCSA=0, WCSN=0 - */ - writel(0x72080F00, &pweim[1].cswcr1); - mx51_io_board = (struct io_board_ctrl *)(CS1_BASE_ADDR + - IO_BOARD_OFFSET); - } - - /* Reset interrupt status reg */ - writew(0x1F, &(mx51_io_board->int_rest)); - writew(0x00, &(mx51_io_board->int_rest)); - writew(0xFFFF, &(mx51_io_board->int_mask)); - - /* Reset the XUART and Ethernet controllers */ - reg = readw(&(mx51_io_board->sw_reset)); - reg |= 0x9; - writew(reg, &(mx51_io_board->sw_reset)); - reg &= ~0x9; - writew(reg, &(mx51_io_board->sw_reset)); -} - static void setup_iomux_fec(void) { /*FEC_MDIO*/ @@ -349,7 +283,6 @@ int board_init(void) gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; setup_iomux_uart(); - setup_expio(); setup_iomux_fec(); return 0; } diff --git a/board/freescale/mx51evk/mx51evk.h b/board/freescale/mx51evk/mx51evk.h index 524cdcc..2854e71 100644 --- a/board/freescale/mx51evk/mx51evk.h +++ b/board/freescale/mx51evk/mx51evk.h @@ -47,5 +47,4 @@ struct io_board_ctrl { }; #endif -#define IO_BOARD_OFFSET (0x20000) #endif -- cgit v1.1 From 16b76705d36ac137fa9231cedfe1355561639e47 Mon Sep 17 00:00:00 2001 From: Siddarth Gore <[gores@marvell.com]> Date: Thu, 18 Mar 2010 20:25:40 +0530 Subject: Marvell GuruPlug Board Support GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0 GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot References: http://www.globalscaletechnologies.com/t-guruplugdetails.aspx http://plugcomputer.org This patch is for GuruPlug Plus, but it supports Standard version as well. Signed-off-by: Siddarth Gore --- board/Marvell/guruplug/Makefile | 51 +++++++++++ board/Marvell/guruplug/config.mk | 27 ++++++ board/Marvell/guruplug/guruplug.c | 167 ++++++++++++++++++++++++++++++++++++ board/Marvell/guruplug/guruplug.h | 39 +++++++++ board/Marvell/guruplug/kwbimage.cfg | 162 ++++++++++++++++++++++++++++++++++ 5 files changed, 446 insertions(+) create mode 100644 board/Marvell/guruplug/Makefile create mode 100644 board/Marvell/guruplug/config.mk create mode 100644 board/Marvell/guruplug/guruplug.c create mode 100644 board/Marvell/guruplug/guruplug.h create mode 100644 board/Marvell/guruplug/kwbimage.cfg (limited to 'board') diff --git a/board/Marvell/guruplug/Makefile b/board/Marvell/guruplug/Makefile new file mode 100644 index 0000000..99748a7 --- /dev/null +++ b/board/Marvell/guruplug/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Siddarth Gore +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := guruplug.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/Marvell/guruplug/config.mk b/board/Marvell/guruplug/config.mk new file mode 100644 index 0000000..caa26b6 --- /dev/null +++ b/board/Marvell/guruplug/config.mk @@ -0,0 +1,27 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Siddarth Gore +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +TEXT_BASE = 0x00600000 + +KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg diff --git a/board/Marvell/guruplug/guruplug.c b/board/Marvell/guruplug/guruplug.c new file mode 100644 index 0000000..ba47ca1 --- /dev/null +++ b/board/Marvell/guruplug/guruplug.c @@ -0,0 +1,167 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Siddarth Gore + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include "guruplug.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_init(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + kw_config_gpio(GURUPLUG_OE_VAL_LOW, + GURUPLUG_OE_VAL_HIGH, + GURUPLUG_OE_LOW, GURUPLUG_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, /* GPIO_RST */ + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GE1_8, + MPP29_GE1_9, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GE1_14, + MPP35_GE1_15, + MPP36_GPIO, + MPP37_GPIO, + MPP38_GPIO, + MPP39_GPIO, + MPP40_TDM_SPI_SCK, + MPP41_TDM_SPI_MISO, + MPP42_TDM_SPI_MOSI, + MPP43_GPIO, + MPP44_GPIO, + MPP45_GPIO, + MPP46_GPIO, /* M_RLED */ + MPP47_GPIO, /* M_GLED */ + MPP48_GPIO, /* B_RLED */ + MPP49_GPIO, /* B_GLED */ + 0 + }; + kirkwood_mpp_conf(kwmpp_config); + + /* + * arch number of board + */ + gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + + return 0; +} + +int dram_init(void) +{ + int i; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + gd->bd->bi_dram[i].start = kw_sdram_bar(i); + gd->bd->bi_dram[i].size = kw_sdram_bs(i); + } + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +void mv_phy_88e1121_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { + printf("Err..%s could not read PHY dev address\n", + __FUNCTION__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®); + reg |= (MV88E1121_RGMII_RXTM_CTRL | MV88E1121_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg); + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0); + + /* reset the phy */ + if (miiphy_read (name, devadr, PHY_BMCR, ®) != 0) { + printf("Err..(%s) PHY status read failed\n", __FUNCTION__); + return; + } + if (miiphy_write (name, devadr, PHY_BMCR, reg | 0x8000) != 0) { + printf("Err..(%s) PHY reset failed\n", __FUNCTION__); + return; + } + + printf("88E1121 Initialized on %s\n", name); +} + +void reset_phy(void) +{ + /* configure and initialize both PHY's */ + mv_phy_88e1121_init("egiga0"); + mv_phy_88e1121_init("egiga1"); +} +#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/guruplug/guruplug.h b/board/Marvell/guruplug/guruplug.h new file mode 100644 index 0000000..5bc16b4 --- /dev/null +++ b/board/Marvell/guruplug/guruplug.h @@ -0,0 +1,39 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Siddarth Gore + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef __GURUPLUG_H +#define __GURUPLUG_H + +#define GURUPLUG_OE_LOW (~(0)) +#define GURUPLUG_OE_HIGH (~(0)) +#define GURUPLUG_OE_VAL_LOW 0 +#define GURUPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high */ + +/* PHY related */ +#define MV88E1121_MAC_CTRL2_REG 21 +#define MV88E1121_PGADR_REG 22 +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) + +#endif /* __GURUPLUG_H */ diff --git a/board/Marvell/guruplug/kwbimage.cfg b/board/Marvell/guruplug/kwbimage.cfg new file mode 100644 index 0000000..2afd927 --- /dev/null +++ b/board/Marvell/guruplug/kwbimage.cfg @@ -0,0 +1,162 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Siddarth Gore +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0/1 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b9b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x000000cc # DDR Address Control +# bit1-0: 01, Cs0width=x8 +# bit3-2: 10, Cs0size=1Gb +# bit5-4: 01, Cs1width=x8 +# bit7-6: 10, Cs1size=1Gb +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000040 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E803 # CPU ODT Control +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 -- cgit v1.1 From dfe83352cb58c55dfdbd5b535cb335526cb1c581 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Tue, 13 Apr 2010 12:38:43 +0200 Subject: mx51evk: correct list of possible BOOT_FROM values Signed-off-by: Stefano Babic --- board/freescale/mx51evk/imximage.cfg | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'board') diff --git a/board/freescale/mx51evk/imximage.cfg b/board/freescale/mx51evk/imximage.cfg index db09913..a875e8f 100644 --- a/board/freescale/mx51evk/imximage.cfg +++ b/board/freescale/mx51evk/imximage.cfg @@ -26,7 +26,7 @@ # The syntax is taken as close as possible with the kwbimage # Boot Device : one of -# spi_flash, nand, onenand, sd_card +# spi, sd (the board has no nand neither onenand) BOOT_FROM spi -- cgit v1.1 From 45997e0a86ee8d8abec6d791a241cb20011fe0e3 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Mon, 29 Mar 2010 16:43:39 +0200 Subject: MX31: Add support for NAND to QONG board The NAND device is connected to the FPGA of the QONG board and not to the NFC controller. For this reason, the FPGA must be set and initialized before accessing to the NAND itself. Signed-off-by: Stefano Babic --- board/davedenx/qong/qong.c | 93 +++++++++++++++++++++++++++++++---------- board/davedenx/qong/qong_fpga.h | 4 +- 2 files changed, 74 insertions(+), 23 deletions(-) (limited to 'board') diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c index b801150..e73d26b 100644 --- a/board/davedenx/qong/qong.c +++ b/board/davedenx/qong/qong.c @@ -25,6 +25,7 @@ #include #include #include +#include #include "qong_fpga.h" DECLARE_GLOBAL_DATA_PTR; @@ -38,6 +39,15 @@ int dram_init (void) return 0; } +static void qong_fpga_reset(void) +{ + mx31_gpio_set(QONG_FPGA_RST_PIN, 0); + udelay(30); + mx31_gpio_set(QONG_FPGA_RST_PIN, 1); + + udelay(300); +} + int board_init (void) { /* Chip selects */ @@ -101,6 +111,15 @@ int board_init (void) mx31_gpio_mux(IOMUX_MODE(0x91, MUX_CTL_OUT_FUNC | MUX_CTL_IN_GPIO)); mx31_gpio_mux(IOMUX_MODE(0x92, MUX_CTL_GPIO)); mx31_gpio_mux(IOMUX_MODE(0x93, MUX_CTL_GPIO)); + + /* FPGA reset Pin */ + /* rstn = 0 */ + mx31_gpio_set(QONG_FPGA_RST_PIN, 0); + mx31_gpio_direction(QONG_FPGA_RST_PIN, MX31_GPIO_DIRECTION_OUT); + + /* set interrupt pin as input */ + mx31_gpio_direction(QONG_FPGA_IRQ_PIN, MX31_GPIO_DIRECTION_IN); + #endif /* setup pins for UART1 */ @@ -127,32 +146,11 @@ int misc_init_r (void) #ifdef CONFIG_QONG_FPGA u32 tmp; - /* FPGA reset */ - /* rstn = 0 */ - tmp = __REG(GPIO2_BASE + GPIO_DR); - tmp &= (~(1 << QONG_FPGA_RST_PIN)); - __REG(GPIO2_BASE + GPIO_DR) = tmp; - /* set the GPIO as output */ - tmp = __REG(GPIO2_BASE + GPIO_GDIR); - tmp |= (1 << QONG_FPGA_RST_PIN); - __REG(GPIO2_BASE + GPIO_GDIR) = tmp; - /* wait */ - udelay(30); - /* rstn = 1 */ - tmp = __REG(GPIO2_BASE + GPIO_DR); - tmp |= (1 << QONG_FPGA_RST_PIN); - __REG(GPIO2_BASE + GPIO_DR) = tmp; - /* set interrupt pin as input */ - __REG(GPIO2_BASE + GPIO_GDIR) = tmp | (1 << QONG_FPGA_IRQ_PIN); - /* wait while the FPGA starts */ - udelay(300); - tmp = *(volatile u32*)QONG_FPGA_CTRL_VERSION; printf("FPGA: "); printf("version register = %u.%u.%u\n", (tmp & 0xF000) >> 12, (tmp & 0x0F00) >> 8, tmp & 0x00FF); #endif - return 0; } @@ -164,3 +162,56 @@ int board_eth_init(bd_t *bis) return 0; #endif } + +#if defined(CONFIG_QONG_FPGA) && defined(CONFIG_NAND_PLAT) +static void board_nand_setup(void) +{ + + /* CS3: NAND 8-bit */ + __REG(CSCR_U(3)) = 0x00004f00; + __REG(CSCR_L(3)) = 0x20013b31; + __REG(CSCR_A(3)) = 0x00020800; + __REG(IOMUXC_GPR) |= 1 << 13; + + mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_WP, MUX_CTL_IN_GPIO)); + mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_CE, MUX_CTL_IN_GPIO)); + mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_RB, MUX_CTL_IN_GPIO)); + + /* Make sure to reset the fpga else you cannot access NAND */ + qong_fpga_reset(); + + /* Enable NAND flash */ + mx31_gpio_set(15, 1); + mx31_gpio_set(14, 1); + mx31_gpio_direction(15, MX31_GPIO_DIRECTION_OUT); + mx31_gpio_direction(16, MX31_GPIO_DIRECTION_IN); + mx31_gpio_direction(14, MX31_GPIO_DIRECTION_IN); + mx31_gpio_set(15, 0); + +} + +int qong_nand_rdy(void *chip) +{ + udelay(1); + return mx31_gpio_get(16); +} + +void qong_nand_select_chip(struct mtd_info *mtd, int chip) +{ + if (chip >= 0) + mx31_gpio_set(15, 0); + else + mx31_gpio_set(15, 1); + +} + +void qong_nand_plat_init(void *chip) +{ + struct nand_chip *nand = (struct nand_chip *)chip; + nand->chip_delay = 20; + nand->select_chip = qong_nand_select_chip; + nand->options &= ~NAND_BUSWIDTH_16; + board_nand_setup(); +} + +#endif diff --git a/board/davedenx/qong/qong_fpga.h b/board/davedenx/qong/qong_fpga.h index e8042b1..4e11f5a 100644 --- a/board/davedenx/qong/qong_fpga.h +++ b/board/davedenx/qong/qong_fpga.h @@ -33,8 +33,8 @@ #define QONG_FPGA_TMS_PIN 25 #define QONG_FPGA_TDI_PIN 8 #define QONG_FPGA_TDO_PIN 7 -#define QONG_FPGA_RST_PIN 16 -#define QONG_FPGA_IRQ_PIN 8 +#define QONG_FPGA_RST_PIN 48 +#define QONG_FPGA_IRQ_PIN 40 #endif #endif /* QONG_FPGA_H */ -- cgit v1.1 From eab40f819ddd50eef465619db1386c053b59a95b Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 31 Mar 2010 10:27:47 +0200 Subject: MX31: Support 128MB RAM on QONG module The QONG module can be downsized and delivered with 128MB instead of 256MB. The patch adds run time support for the two different memory configurations. Signed-off-by: Stefano Babic --- board/davedenx/qong/lowlevel_init.S | 130 +++++++++++++++++++++++++++--------- 1 file changed, 97 insertions(+), 33 deletions(-) (limited to 'board') diff --git a/board/davedenx/qong/lowlevel_init.S b/board/davedenx/qong/lowlevel_init.S index 198dd76..80bed92 100644 --- a/board/davedenx/qong/lowlevel_init.S +++ b/board/davedenx/qong/lowlevel_init.S @@ -42,6 +42,27 @@ bcs 1b .endm +.macro SETUP_RAM cfg, ctl + /* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */ + REG 0xB8001010, 0x00000004 + ldr r3, =\cfg + ldr r2, =WEIM_ESDCFG0 + str r3, [r2] + REG 0xB8001000, 0x92100000 + REG 0x80000f00, 0x12344321 + REG 0xB8001000, 0xa2100000 + REG 0x80000000, 0x12344321 + REG 0x80000000, 0x12344321 + REG 0xB8001000, 0xb2100000 + REG8 0x80000033, 0xda + REG8 0x81000000, 0xff + ldr r3, =\ctl + ldr r2, =WEIM_ESDCTL0 + str r3, [r2] + REG 0x80000000, 0xDEADBEEF + REG 0xB8001010, 0x0000000c + +.endm /* RedBoot: To support 133MHz DDR */ .macro init_drive_strength /* @@ -130,43 +151,86 @@ lowlevel_init: /* Default: 1, 4, 12, 1 */ REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1) - /* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */ - REG 0xB8001010, 0x00000004 - REG 0xB8001004, ((3 << 21) | /* tXP */ \ - (0 << 20) | /* tWTR */ \ - (2 << 18) | /* tRP */ \ - (1 << 16) | /* tMRD */ \ - (0 << 15) | /* tWR */ \ - (5 << 12) | /* tRAS */ \ - (1 << 10) | /* tRRD */ \ - (3 << 8) | /* tCAS */ \ - (2 << 4) | /* tRCD */ \ - (7 << 0) /* tRC */ ) - REG 0xB8001000, 0x92100000 - REG 0x80000f00, 0x12344321 - REG 0xB8001000, 0xa2100000 - REG 0x80000000, 0x12344321 - REG 0x80000000, 0x12344321 - REG 0xB8001000, 0xb2100000 - REG8 0x80000033, 0xda - REG8 0x81000000, 0xff - REG 0xB8001000, ((1 << 31) | \ - (0 << 28) | \ - (0 << 27) | \ - (3 << 24) | /* 14 rows */ \ - (2 << 20) | /* 10 cols */ \ - (2 << 16) | \ - (4 << 13) | /* 3.91us (64ms/16384) */ \ - (0 << 10) | \ - (0 << 8) | \ - (1 << 7) | \ - (0 << 0)) - REG 0x80000000, 0xDEADBEEF - REG 0xB8001010, 0x0000000c +check_ddr_module: +/* Set stackpointer in internal RAM to call get_ram_size */ + ldr sp, =(IRAM_BASE_ADDR + IRAM_SIZE - 16) + stmfd sp!, {r0-r11, ip, lr} + mov ip, lr /* save link reg across call */ + + ldr r0,=0x08000000 + SETUP_RAM ESDCFG0_256MB, ESDCTL0_256MB + ldr r0,=0x80000000 + ldr r1,=0x10000000 + bl get_ram_size + ldr r1,=0x10000000 + cmp r0,r1 + beq restore_regs + SETUP_RAM ESDCFG0_128MB, ESDCTL0_128MB + ldr r0,=0x80000000 + ldr r1,=0x08000000 + bl get_ram_size + ldr r1,=0x08000000 + cmp r0,r1 + beq restore_regs + +restore_regs: + ldmfd sp!, {r0-r11, ip, lr} + mov lr, ip /* restore link reg */ mov pc, lr + MPCTL_PARAM_399: .word (((1 - 1) << 26) + ((52 - 1) << 16) + (7 << 10) + (35 << 0)) UPCTL_PARAM_240: .word (((2 - 1) << 26) + ((13 - 1) << 16) + (9 << 10) + (3 << 0)) + + .equ ESDCFG0_128MB, \ + (0 << 21) + /* tXP */ \ + (1 << 20) + /* tWTR */ \ + (2 << 18) + /* tRP */ \ + (1 << 16) + /* tMRD */ \ + (0 << 15) + /* tWR */ \ + (5 << 12) + /* tRAS */ \ + (1 << 10) + /* tRRD */ \ + (3 << 8) + /* tCAS */ \ + (2 << 4) + /* tRCD */ \ + (0x0F << 0) /* tRC */ + + .equ ESDCTL0_128MB, \ + (1 << 31) + /* enable */ \ + (0 << 28) + /* mode */ \ + (0 << 27) + /* supervisor protect */ \ + (2 << 24) + /* 13 rows */ \ + (2 << 20) + /* 10 cols */ \ + (2 << 16) + /* 32 bit */ \ + (3 << 13) + /* 7.81us (64ms/8192) */ \ + (0 << 10) + /* power down timer */ \ + (0 << 8) + /* full page */ \ + (1 << 7) + /* burst length */ \ + (0 << 0) /* precharge timer */ + + .equ ESDCFG0_256MB, \ + (3 << 21) + /* tXP */ \ + (0 << 20) + /* tWTR */ \ + (2 << 18) + /* tRP */ \ + (1 << 16) + /* tMRD */ \ + (0 << 15) + /* tWR */ \ + (5 << 12) + /* tRAS */ \ + (1 << 10) + /* tRRD */ \ + (3 << 8) + /* tCAS */ \ + (2 << 4) + /* tRCD */ \ + (7 << 0) /* tRC */ + + .equ ESDCTL0_256MB, \ + (1 << 31) + \ + (0 << 28) + \ + (0 << 27) + \ + (3 << 24) + /* 14 rows */ \ + (2 << 20) + /* 10 cols */ \ + (2 << 16) + \ + (4 << 13) + /* 3.91us (64ms/16384) */ \ + (0 << 10) + \ + (0 << 8) + \ + (1 << 7) + \ + (0 << 0) -- cgit v1.1 From eeb50ce193453951529015f50e5c1ccd7b55aad2 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Tue, 13 Apr 2010 12:19:06 +0200 Subject: MX31: Removed erroneous board name from QONG QONG is a module that can be installed on several boards, not only on the QONG-EVB manufactured by Dave srl. Signed-off-by: Stefano Babic --- board/davedenx/qong/qong.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'board') diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c index e73d26b..eb9218e 100644 --- a/board/davedenx/qong/qong.c +++ b/board/davedenx/qong/qong.c @@ -137,7 +137,7 @@ int board_init (void) int checkboard (void) { - printf("Board: DAVE/DENX QongEVB-LITE\n"); + printf("Board: DAVE/DENX Qong\n"); return 0; } -- cgit v1.1 From 20d98c2cea3398ad93beccd4727a371f41514086 Mon Sep 17 00:00:00 2001 From: Asen Dimov Date: Mon, 19 Apr 2010 14:18:43 +0300 Subject: pm9263 converted to at91 soc access Signed-off-by: Asen Dimov --- board/ronetix/pm9263/led.c | 15 ++-- board/ronetix/pm9263/pm9263.c | 195 ++++++++++++++++++++++-------------------- 2 files changed, 109 insertions(+), 101 deletions(-) (limited to 'board') diff --git a/board/ronetix/pm9263/led.c b/board/ronetix/pm9263/led.c index fe1a1d2..4e585a4 100644 --- a/board/ronetix/pm9263/led.c +++ b/board/ronetix/pm9263/led.c @@ -26,18 +26,19 @@ #include #include #include -#include +#include #include void coloured_LED_init(void) { + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + /* Enable clock */ - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_PIOB | - 1 << AT91SAM9263_ID_PIOCDE); + writel(1 << AT91SAM9263_ID_PIOB, &pmc->pcer); - at91_set_gpio_output(CONFIG_RED_LED, 1); - at91_set_gpio_output(CONFIG_GREEN_LED, 1); + at91_set_pio_output(CONFIG_RED_LED, 1); + at91_set_pio_output(CONFIG_GREEN_LED, 1); - at91_set_gpio_value(CONFIG_RED_LED, 0); - at91_set_gpio_value(CONFIG_GREEN_LED, 1); + at91_set_pio_value(CONFIG_RED_LED, 0); + at91_set_pio_value(CONFIG_GREEN_LED, 1); } diff --git a/board/ronetix/pm9263/pm9263.c b/board/ronetix/pm9263/pm9263.c index 23ea154..c7835de 100644 --- a/board/ronetix/pm9263/pm9263.c +++ b/board/ronetix/pm9263/pm9263.c @@ -27,13 +27,13 @@ #include #include #include -#include #include #include #include #include +#include +#include #include -#include #include #include #include @@ -55,52 +55,59 @@ DECLARE_GLOBAL_DATA_PTR; static void pm9263_nand_hw_init(void) { unsigned long csa; + at91_smc_t *smc = (at91_smc_t *) AT91_SMC0_BASE; + at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE; /* Enable CS3 */ - csa = at91_sys_read(AT91_MATRIX_EBI0CSA); - at91_sys_write(AT91_MATRIX_EBI0CSA, - csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA); + csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A; + writel(csa, &matrix->csa[0]); /* Configure SMC CS3 for NAND/SmartMedia */ - at91_sys_write(AT91_SMC_SETUP(3), - AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(1) | - AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(1)); - at91_sys_write(AT91_SMC_PULSE(3), - AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) | - AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), - AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); - at91_sys_write(AT91_SMC_MODE(3), - AT91_SMC_READMODE | AT91_SMC_WRITEMODE | - AT91_SMC_EXNWMODE_DISABLE | + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1), + &smc->cs[3].setup); + + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); + + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | #ifdef CONFIG_SYS_NAND_DBW_16 - AT91_SMC_DBW_16 | + AT91_SMC_MODE_DBW_16 | #else /* CONFIG_SYS_NAND_DBW_8 */ - AT91_SMC_DBW_8 | + AT91_SMC_MODE_DBW_8 | #endif - AT91_SMC_TDF_(2)); + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); /* Configure RDY/BSY */ - at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); + at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1); /* Enable NandFlash */ - at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); + at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); } #endif #ifdef CONFIG_MACB static void pm9263_macb_hw_init(void) { + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + at91_pio_t *pio = (at91_pio_t *) AT91_PIO_BASE; + /* * PB27 enables the 50MHz oscillator for Ethernet PHY * 1 - enable * 0 - disable */ - at91_set_gpio_output(AT91_PIN_PB27, 1); - at91_set_gpio_value(AT91_PIN_PB27, 1); /* 1- enable, 0 - disable */ + at91_set_pio_output(AT91_PIO_PORTB, 27, 1); + at91_set_pio_value(AT91_PIO_PORTB, 27, 1); /* 1- enable, 0 - disable */ /* Enable clock */ - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_EMAC); + writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer); /* * Disable pull-up on: @@ -110,19 +117,15 @@ static void pm9263_macb_hw_init(void) * * PHY has internal pull-down */ - writel(pin_to_mask(AT91_PIN_PC25), - pin_to_controller(AT91_PIN_PC0) + PIO_PUDR); - writel(pin_to_mask(AT91_PIN_PE25) | - pin_to_mask(AT91_PIN_PE26), - pin_to_controller(AT91_PIN_PE0) + PIO_PUDR); + at91_set_pio_pullup(AT91_PIO_PORTC, 25, 0); + at91_set_pio_pullup(AT91_PIO_PORTE, 25, 0); + at91_set_pio_pullup(AT91_PIO_PORTE, 26, 0); /* Re-enable pull-up */ - writel(pin_to_mask(AT91_PIN_PC25), - pin_to_controller(AT91_PIN_PC0) + PIO_PUER); - writel(pin_to_mask(AT91_PIN_PE25) | - pin_to_mask(AT91_PIN_PE26), - pin_to_controller(AT91_PIN_PE0) + PIO_PUER); + at91_set_pio_pullup(AT91_PIO_PORTC, 25, 1); + at91_set_pio_pullup(AT91_PIO_PORTE, 25, 1); + at91_set_pio_pullup(AT91_PIO_PORTE, 26, 1); at91_macb_hw_init(); } @@ -148,17 +151,17 @@ vidinfo_t panel_info = { void lcd_enable(void) { - at91_set_gpio_value(AT91_PIN_PA22, 1); /* power up */ + at91_set_pio_value(AT91_PIO_PORTA, 22, 1); /* power up */ } void lcd_disable(void) { - at91_set_gpio_value(AT91_PIN_PA22, 0); /* power down */ + at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power down */ } #ifdef CONFIG_LCD_IN_PSRAM -#define PSRAM_CRE_PIN AT91_PIN_PB29 +#define PSRAM_CRE_PIN AT91_PIO_PORTB, 29 #define PSRAM_CTRL_REG (PHYS_PSRAM + PHYS_PSRAM_SIZE - 2) /* Initialize the PSRAM memory */ @@ -166,31 +169,34 @@ static int pm9263_lcd_hw_psram_init(void) { volatile uint16_t x; unsigned long csa; + at91_smc_t *smc = (at91_smc_t *) AT91_SMC1_BASE; + at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE; /* Enable CS3 3.3v, no pull-ups */ - csa = at91_sys_read(AT91_MATRIX_EBI1CSA); - at91_sys_write(AT91_MATRIX_EBI1CSA, - csa | AT91_MATRIX_EBI1_DBPUC | - AT91_MATRIX_EBI1_VDDIOMSEL_3_3V); + csa = readl(&matrix->csa[1]) | AT91_MATRIX_CSA_DBPUC | + AT91_MATRIX_CSA_VDDIOMSEL_3_3V; + + writel(csa, &matrix->csa[1]); /* Configure SMC1 CS0 for PSRAM - 16-bit */ - at91_sys_write(AT91_SMC1_SETUP(0), - AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC1_PULSE(0), - AT91_SMC_NWEPULSE_(7) | AT91_SMC_NCS_WRPULSE_(7) | - AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(7)); - at91_sys_write(AT91_SMC1_CYCLE(0), - AT91_SMC_NWECYCLE_(8) | AT91_SMC_NRDCYCLE_(8)); - at91_sys_write(AT91_SMC1_MODE(0), - AT91_SMC_DBW_16 | - AT91_SMC_PMEN | - AT91_SMC_PS_32); + writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[0].setup); + + writel(AT91_SMC_PULSE_NWE(7) | AT91_SMC_PULSE_NCS_WR(7) | + AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(7), + &smc->cs[0].pulse); + + writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8), + &smc->cs[0].cycle); + + writel(AT91_SMC_MODE_DBW_16 | AT91_SMC_MODE_PMEN | AT91_SMC_MODE_PS_32, + &smc->cs[0].mode); /* setup PB29 as output */ - at91_set_gpio_output(PSRAM_CRE_PIN, 1); + at91_set_pio_output(PSRAM_CRE_PIN, 1); - at91_set_gpio_value(PSRAM_CRE_PIN, 0); /* set PSRAM_CRE_PIN to '0' */ + at91_set_pio_value(PSRAM_CRE_PIN, 0); /* set PSRAM_CRE_PIN to '0' */ /* PSRAM: write BCR */ x = readw(PSRAM_CTRL_REG); @@ -216,7 +222,7 @@ static int pm9263_lcd_hw_psram_init(void) /* test if the chip is MT45W2M16B */ if ((readw(PHYS_PSRAM) != 0x1234) || (readw(PHYS_PSRAM+2) != 0x5678)) { /* try with CRE=1 (MT45W2M16A) */ - at91_set_gpio_value(PSRAM_CRE_PIN, 1); /* set PSRAM_CRE_PIN to '1' */ + at91_set_pio_value(PSRAM_CRE_PIN, 1); /* set PSRAM_CRE_PIN to '1' */ /* write RCR of the PSRAM */ x = readw(PSRAM_CTRL_REG); @@ -229,17 +235,14 @@ static int pm9263_lcd_hw_psram_init(void) writew(0x1234, PHYS_PSRAM); writew(0x5678, PHYS_PSRAM+2); if ((readw(PHYS_PSRAM) != 0x1234) - || (readw(PHYS_PSRAM + 2) != 0x5678)) + || (readw(PHYS_PSRAM + 2) != 0x5678)) return 1; } /* Bus matrix */ - at91_sys_write( AT91_MATRIX_PRAS5, AT91_MATRIX_M5PR ); - at91_sys_write( AT91_MATRIX_SCFG5, AT91_MATRIX_ARBT_FIXED_PRIORITY | - (AT91_MATRIX_FIXED_DEFMSTR & (5 << 18)) | - AT91_MATRIX_DEFMSTR_TYPE_FIXED | - (AT91_MATRIX_SLOT_CYCLE & (0xFF << 0))); + writel(AT91_MATRIX_PRA_M5(3), &matrix->pr[5].a); + writel(CONFIG_PSRAM_SCFG, &matrix->scfg[5]); return 0; } @@ -247,35 +250,37 @@ static int pm9263_lcd_hw_psram_init(void) static void pm9263_lcd_hw_init(void) { - at91_set_A_periph(AT91_PIN_PC0, 0); /* LCDVSYNC */ - at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */ - at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */ - at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */ - at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */ - at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */ - at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */ - at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */ - at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */ - at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */ - at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */ - at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */ - at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */ - at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */ - at91_set_B_periph(AT91_PIN_PC12, 0); /* LCDD13 */ - at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */ - at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */ - at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */ - at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */ - at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */ - at91_set_B_periph(AT91_PIN_PC17, 0); /* LCDD21 */ - at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */ - at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */ - - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_LCDC); + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + + at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDVSYNC */ + at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */ + at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */ + at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */ + at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */ + at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */ + at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */ + at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */ + at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */ + at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */ + at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */ + at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */ + at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */ + at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */ + at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */ + at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */ + at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */ + at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */ + at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */ + at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */ + at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */ + at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */ + at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */ + + writel(1 << AT91SAM9263_ID_LCDC, &pmc->pcer); /* Power Control */ - at91_set_gpio_output(AT91_PIN_PA22, 1); - at91_set_gpio_value(AT91_PIN_PA22, 0); /* power down */ + at91_set_pio_output(AT91_PIO_PORTA, 22, 1); + at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power down */ #ifdef CONFIG_LCD_IN_PSRAM /* initialize te PSRAM */ @@ -337,13 +342,15 @@ void lcd_show_board_info(void) int board_init(void) { + at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + /* Enable Ctrlc */ console_init_f(); - at91_sys_write(AT91_PMC_PCER, - (1 << AT91SAM9263_ID_PIOA) | - (1 << AT91SAM9263_ID_PIOCDE) | - (1 << AT91SAM9263_ID_PIOB)); + writel((1 << AT91SAM9263_ID_PIOA) | + (1 << AT91SAM9263_ID_PIOCDE) | + (1 << AT91SAM9263_ID_PIOB), + &pmc->pcer); /* arch number of AT91SAM9263EK-Board */ gd->bd->bi_arch_number = MACH_TYPE_PM9263; @@ -394,7 +401,7 @@ int board_eth_init(bd_t *bis) { int rc = 0; #ifdef CONFIG_MACB - rc = macb_eth_initialize(0, (void *)AT91SAM9263_BASE_EMAC, 0x01); + rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x01); #endif return rc; } -- cgit v1.1