From 6d9ea159e4900dc6bc4b38a064fc87cba4582c09 Mon Sep 17 00:00:00 2001 From: Tom Warren Date: Mon, 18 Mar 2013 14:51:20 -0700 Subject: Tegra114: MMC: Add SD bus power-rail init routine T114 requires SD bus power-rail bringup for the SDIO card on SDMMC3. Signed-off-by: Tom Warren Reviewed-by: Stephen Warren --- board/nvidia/dalmore/dalmore.c | 62 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+) (limited to 'board') diff --git a/board/nvidia/dalmore/dalmore.c b/board/nvidia/dalmore/dalmore.c index 7449b5b..2c23a29 100644 --- a/board/nvidia/dalmore/dalmore.c +++ b/board/nvidia/dalmore/dalmore.c @@ -18,6 +18,10 @@ #include #include #include "pinmux-config-dalmore.h" +#include + +#define BAT_I2C_ADDRESS 0x48 /* TPS65090 charger */ +#define PMU_I2C_ADDRESS 0x58 /* TPS65913 PMU */ /* * Routine: pinmux_init @@ -37,3 +41,61 @@ void pinmux_init(void) /* Initialize any non-default pad configs (APB_MISC_GP regs) */ padgrp_config_table(dalmore_padctrl, ARRAY_SIZE(dalmore_padctrl)); } + +#if defined(CONFIG_TEGRA_MMC) +/* + * Do I2C/PMU writes to bring up SD card bus power + * + */ +void board_sdmmc_voltage_init(void) +{ + uchar reg, data_buffer[1]; + int ret; + + ret = i2c_set_bus_num(0);/* PMU is on bus 0 */ + if (ret) + printf("%s: i2c_set_bus_num returned %d\n", __func__, ret); + + /* TPS65913: LDO9_VOLTAGE = 3.3V */ + data_buffer[0] = 0x31; + reg = 0x61; + + ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1); + if (ret) + printf("%s: PMU i2c_write %02X<-%02X returned %d\n", + __func__, reg, data_buffer[0], ret); + + /* TPS65913: LDO9_CTRL = Active */ + data_buffer[0] = 0x01; + reg = 0x60; + + ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1); + if (ret) + printf("%s: PMU i2c_write %02X<-%02X returned %d\n", + __func__, reg, data_buffer[0], ret); + + /* TPS65090: FET6_CTRL = enable output auto discharge, enable FET6 */ + data_buffer[0] = 0x03; + reg = 0x14; + + ret = i2c_write(BAT_I2C_ADDRESS, reg, 1, data_buffer, 1); + if (ret) + printf("%s: BAT i2c_write %02X<-%02X returned %d\n", + __func__, reg, data_buffer[0], ret); +} + +/* + * Routine: pin_mux_mmc + * Description: setup the MMC muxes, power rails, etc. + */ +void pin_mux_mmc(void) +{ + /* + * NOTE: We don't do mmc-specific pin muxes here. + * They were done globally in pinmux_init(). + */ + + /* Bring up the SDIO3 power rail */ + board_sdmmc_voltage_init(); +} +#endif /* MMC */ -- cgit v1.1