From 85eb0de2147307eaf70f21f59e805fc9a3585550 Mon Sep 17 00:00:00 2001 From: pekon gupta Date: Tue, 22 Jul 2014 16:03:20 +0530 Subject: board/ti/am335x: add support for beaglebone NAND cape Beaglebone Board can be connected to expansion boards to add devices to them. These expansion boards are called 'capes'. This patch adds support for following versions of Beaglebone(AM335x) NAND capes (a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64 (b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224 Further information and datasheets can be found at [1] and [2] * How to boot from NAND using Memory Expander + NAND Cape ? * - Important: As BOOTSEL values are sampled only at POR, so after changing any setting on SW2 (DIP switch), disconnect and reconnect all board power supply (including mini-USB console port) to POR the beaglebone. - Selection of ECC scheme for NAND cape(a), ROM code expects BCH8_HW ecc-scheme for NAND cape(b), ROM code expects BCH16_HW ecc-scheme - Selction of boot modes can be controlled via DIP switch(SW2) present on Memory Expander cape. SW2[SWITCH_BOOT] == OFF follow default boot order MMC-> SPI -> UART -> USB SW2[SWITCH_BOOT] == ON boot mode selected via DIP switch(SW2) So to flash NAND, first boot via MMC or other sources and then switch to SW2[SWITCH_BOOT]=ON to boot from NAND Cape. - For NAND boot following switch settings need to be followed SW2[ 1] = OFF (SYSBOOT[ 0]==1: NAND boot mode selected ) SW2[ 2] = OFF (SYSBOOT[ 1]==1: -- do -- ) SW2[ 3] = ON (SYSBOOT[ 2]==0: -- do -- ) SW2[ 4] = ON (SYSBOOT[ 3]==0: -- do -- ) SW2[ 5] = OFF (SYSBOOT[ 4]==1: -- do -- ) SW2[ 6] = OFF (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device ) SW2[ 7] = ON (SYSBOOT[ 9]==0: ECC done by ROM ) SW2[ 8] = ON (SYSBOOT[10]==0: Non Muxed device ) SW2[ 9] = ON (SYSBOOT[11]==0: -- do -- ) [1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion [2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module *IMPORTANT NOTE* As Beaglebone board shares the same config as AM335x EVM, so following changes are required in addition to this patch for Beaglebone NAND cape. (1) Enable NAND in am335x_beaglebone board profile (2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because: - AM335x EVM has NAND device with datawidth=8, whereas - Beaglebone NAND cape has NAND device with data-width=16 --- board/ti/am335x/mux.c | 58 +++++++++++++++++++++++++++++++++------------------ 1 file changed, 38 insertions(+), 20 deletions(-) (limited to 'board/ti') diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c index b2bfda5..439da4b 100644 --- a/board/ti/am335x/mux.c +++ b/board/ti/am335x/mux.c @@ -171,25 +171,36 @@ static struct module_pin_mux mii1_pin_mux[] = { {-1}, }; +#ifdef CONFIG_NAND static struct module_pin_mux nand_pin_mux[] = { - {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */ - {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */ - {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */ - {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */ - {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */ - {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */ - {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */ - {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */ - {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */ - {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */ - {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */ - {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */ - {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */ - {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */ - {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */ + {OFFSET(gpmc_ad0), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD0 */ + {OFFSET(gpmc_ad1), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD1 */ + {OFFSET(gpmc_ad2), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD2 */ + {OFFSET(gpmc_ad3), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD3 */ + {OFFSET(gpmc_ad4), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD4 */ + {OFFSET(gpmc_ad5), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD5 */ + {OFFSET(gpmc_ad6), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD6 */ + {OFFSET(gpmc_ad7), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD7 */ +#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT + {OFFSET(gpmc_ad8), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD8 */ + {OFFSET(gpmc_ad9), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD9 */ + {OFFSET(gpmc_ad10), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD10 */ + {OFFSET(gpmc_ad11), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD11 */ + {OFFSET(gpmc_ad12), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD12 */ + {OFFSET(gpmc_ad13), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD13 */ + {OFFSET(gpmc_ad14), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD14 */ + {OFFSET(gpmc_ad15), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD15 */ +#endif + {OFFSET(gpmc_wait0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* nWAIT */ + {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN)}, /* nWP */ + {OFFSET(gpmc_csn0), (MODE(0) | PULLUP_EN)}, /* nCS */ + {OFFSET(gpmc_wen), (MODE(0) | PULLDOWN_EN)}, /* WEN */ + {OFFSET(gpmc_oen_ren), (MODE(0) | PULLDOWN_EN)}, /* OE */ + {OFFSET(gpmc_advn_ale), (MODE(0) | PULLDOWN_EN)}, /* ADV_ALE */ + {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLDOWN_EN)}, /* BE_CLE */ {-1}, }; - +#endif #if defined(CONFIG_NOR) && !defined(CONFIG_NOR_BOOT) static struct module_pin_mux bone_norcape_pin_mux[] = { {OFFSET(lcd_data0), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A0 */ @@ -336,11 +347,12 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) configure_module_pin_mux(i2c1_pin_mux); configure_module_pin_mux(mii1_pin_mux); configure_module_pin_mux(mmc0_pin_mux); -#ifndef CONFIG_NOR - configure_module_pin_mux(mmc1_pin_mux); -#endif -#if defined(CONFIG_NOR) && !defined(CONFIG_NOR_BOOT) +#if defined(CONFIG_NAND) + configure_module_pin_mux(nand_pin_mux); +#elif defined(CONFIG_NOR) && !defined(CONFIG_NOR_BOOT) configure_module_pin_mux(bone_norcape_pin_mux); +#else + configure_module_pin_mux(mmc1_pin_mux); #endif } else if (board_is_gp_evm(header)) { /* General Purpose EVM */ @@ -351,8 +363,10 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) if (profile & ~PROFILE_2) configure_module_pin_mux(i2c1_pin_mux); /* Profiles 2 & 3 don't have NAND */ +#ifdef CONFIG_NAND if (profile & ~(PROFILE_2 | PROFILE_3)) configure_module_pin_mux(nand_pin_mux); +#endif else if (profile == PROFILE_2) { configure_module_pin_mux(mmc1_pin_mux); configure_module_pin_mux(spi0_pin_mux); @@ -377,7 +391,11 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) configure_module_pin_mux(i2c1_pin_mux); configure_module_pin_mux(mii1_pin_mux); configure_module_pin_mux(mmc0_pin_mux); +#if defined(CONFIG_NAND) + configure_module_pin_mux(nand_pin_mux); +#else configure_module_pin_mux(mmc1_pin_mux); +#endif } else { puts("Unknown board, cannot configure pinmux."); hang(); -- cgit v1.1 From 3df3bc1e1dc4c38de93d66fb589565f36d9749c7 Mon Sep 17 00:00:00 2001 From: pekon gupta Date: Tue, 22 Jul 2014 16:03:21 +0530 Subject: board/ti/am335x: add support for beaglebone NOR Cape This patch adds support of NOR cape[1] for both Beaglebone (white) and Beaglebone(Black) boards. NOR Flash on this cape is connected to GPMC chip-select[0] and accesses as external memory-mapped device. This cape has 128Mbits(16MBytes), x16, CFI compatible NOR Flash device. As GPMC chip-select[0] can be shared by multiple capes so NOR profile is not enabled by default in boards.cfg. Following changes are required to enable NOR cape detection when building am335x_boneblack board profile. Signed-off-by: Tom Rini --- board/ti/am335x/mux.c | 95 +++++++++++++++++++-------------------------------- 1 file changed, 35 insertions(+), 60 deletions(-) (limited to 'board/ti') diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c index 439da4b..2a18ccb 100644 --- a/board/ti/am335x/mux.c +++ b/board/ti/am335x/mux.c @@ -200,73 +200,46 @@ static struct module_pin_mux nand_pin_mux[] = { {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLDOWN_EN)}, /* BE_CLE */ {-1}, }; -#endif -#if defined(CONFIG_NOR) && !defined(CONFIG_NOR_BOOT) +#elif defined(CONFIG_NOR) static struct module_pin_mux bone_norcape_pin_mux[] = { - {OFFSET(lcd_data0), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A0 */ - {OFFSET(lcd_data1), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A1 */ - {OFFSET(lcd_data2), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A2 */ - {OFFSET(lcd_data3), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A3 */ - {OFFSET(lcd_data4), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A4 */ - {OFFSET(lcd_data5), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A5 */ - {OFFSET(lcd_data6), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A6 */ - {OFFSET(lcd_data7), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A7 */ - {OFFSET(lcd_vsync), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A8 */ - {OFFSET(lcd_hsync), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A9 */ - {OFFSET(lcd_pclk), MODE(1)| PULLUDEN | RXACTIVE}, /* NOR_A10 */ - {OFFSET(lcd_ac_bias_en), MODE(1)| PULLUDEN | RXACTIVE}, /* NOR_A11 */ - {OFFSET(lcd_data8), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A12 */ - {OFFSET(lcd_data9), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A13 */ - {OFFSET(lcd_data10), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A14 */ - {OFFSET(lcd_data11), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A15 */ - {OFFSET(lcd_data12), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A16 */ - {OFFSET(lcd_data13), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A17 */ - {OFFSET(lcd_data14), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A18 */ - {OFFSET(lcd_data15), MODE(1) | PULLUDEN | RXACTIVE}, /* NOR_A19 */ - {OFFSET(gpmc_ad0), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD0 */ - {OFFSET(gpmc_ad1), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD1 */ - {OFFSET(gpmc_ad2), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD2 */ - {OFFSET(gpmc_ad3), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD3 */ - {OFFSET(gpmc_ad4), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD4 */ - {OFFSET(gpmc_ad5), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD5 */ - {OFFSET(gpmc_ad6), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD6 */ - {OFFSET(gpmc_ad7), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD7 */ - {OFFSET(gpmc_ad8), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD8 */ - {OFFSET(gpmc_ad9), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD9 */ - {OFFSET(gpmc_ad10), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD10 */ - {OFFSET(gpmc_ad11), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD11 */ - {OFFSET(gpmc_ad12), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD12 */ - {OFFSET(gpmc_ad13), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD13 */ - {OFFSET(gpmc_ad14), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD14 */ - {OFFSET(gpmc_ad15), MODE(0) | PULLUDEN | RXACTIVE}, /* NOR_AD15 */ - - {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN) | RXACTIVE}, /* NOR_CE */ - {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN) | RXACTIVE}, /* NOR_ADVN_ALE */ - {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN | RXACTIVE)},/* NOR_OE */ - {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN | RXACTIVE)},/* NOR_BE0N_CLE */ - {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN | RXACTIVE)}, /* NOR_WEN */ - {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUDEN)}, /* NOR WAIT */ + {OFFSET(gpmc_a0), MODE(0) | PULLUDDIS}, /* NOR_A0 */ + {OFFSET(gpmc_a1), MODE(0) | PULLUDDIS}, /* NOR_A1 */ + {OFFSET(gpmc_a2), MODE(0) | PULLUDDIS}, /* NOR_A2 */ + {OFFSET(gpmc_a3), MODE(0) | PULLUDDIS}, /* NOR_A3 */ + {OFFSET(gpmc_a4), MODE(0) | PULLUDDIS}, /* NOR_A4 */ + {OFFSET(gpmc_a5), MODE(0) | PULLUDDIS}, /* NOR_A5 */ + {OFFSET(gpmc_a6), MODE(0) | PULLUDDIS}, /* NOR_A6 */ + {OFFSET(gpmc_a7), MODE(0) | PULLUDDIS}, /* NOR_A7 */ + {OFFSET(gpmc_ad0), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD0 */ + {OFFSET(gpmc_ad1), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD1 */ + {OFFSET(gpmc_ad2), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD2 */ + {OFFSET(gpmc_ad3), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD3 */ + {OFFSET(gpmc_ad4), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD4 */ + {OFFSET(gpmc_ad5), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD5 */ + {OFFSET(gpmc_ad6), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD6 */ + {OFFSET(gpmc_ad7), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD7 */ + {OFFSET(gpmc_ad8), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD8 */ + {OFFSET(gpmc_ad9), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD9 */ + {OFFSET(gpmc_ad10), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD10 */ + {OFFSET(gpmc_ad11), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD11 */ + {OFFSET(gpmc_ad12), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD12 */ + {OFFSET(gpmc_ad13), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD13 */ + {OFFSET(gpmc_ad14), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD14 */ + {OFFSET(gpmc_ad15), MODE(0) | PULLUDDIS | RXACTIVE}, /* NOR_AD15 */ + {OFFSET(gpmc_csn0), MODE(0) | PULLUDEN | PULLUP_EN}, /* CE */ + {OFFSET(gpmc_advn_ale), MODE(0) | PULLUDEN | PULLDOWN_EN}, /* ALE */ + {OFFSET(gpmc_oen_ren), MODE(0) | PULLUDEN | PULLDOWN_EN},/* OEn_REN */ + {OFFSET(gpmc_be0n_cle), MODE(0) | PULLUDEN | PULLDOWN_EN},/* unused */ + {OFFSET(gpmc_wen), MODE(0) | PULLUDEN | PULLDOWN_EN}, /* WEN */ + {OFFSET(gpmc_wait0), MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE},/*WAIT*/ {-1}, }; #endif #if defined(CONFIG_NOR_BOOT) -static struct module_pin_mux norboot_pin_mux[] = { - {OFFSET(lcd_data1), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data2), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data3), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data4), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data5), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data6), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data7), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data8), MODE(1) | PULLUDDIS}, - {OFFSET(lcd_data9), MODE(1) | PULLUDDIS}, - {-1}, -}; - void enable_norboot_pin_mux(void) { - configure_module_pin_mux(norboot_pin_mux); + configure_module_pin_mux(bone_norcape_pin_mux); } #endif @@ -349,7 +322,7 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) configure_module_pin_mux(mmc0_pin_mux); #if defined(CONFIG_NAND) configure_module_pin_mux(nand_pin_mux); -#elif defined(CONFIG_NOR) && !defined(CONFIG_NOR_BOOT) +#elif defined(CONFIG_NOR) configure_module_pin_mux(bone_norcape_pin_mux); #else configure_module_pin_mux(mmc1_pin_mux); @@ -393,6 +366,8 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) configure_module_pin_mux(mmc0_pin_mux); #if defined(CONFIG_NAND) configure_module_pin_mux(nand_pin_mux); +#elif defined(CONFIG_NOR) + configure_module_pin_mux(bone_norcape_pin_mux); #else configure_module_pin_mux(mmc1_pin_mux); #endif -- cgit v1.1 From e53ad4b445464327aebd1c5ea6260b7bb9b80ae7 Mon Sep 17 00:00:00 2001 From: pekon gupta Date: Tue, 22 Jul 2014 16:03:22 +0530 Subject: board/ti/am43xx: add support for parallel NAND This patch adds support for NAND device connected to GPMC chip-select on following AM43xx EVM boards. am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a time either eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled by: (a) Statically using Jumper on connecter (J89) present on board. (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled by driving SPI2_CS0[MUX_MODE=GPIO] pin via software: SPI2_CS0 == 0: NAND (default) SPI2_CS0 == 1: eMMC am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI, Thus only one of the two can be used at a time. Selection is controlled by: (a) Dynamically driving following GPIO pin from software GPMC_A0(GPIO) == 0 NAND is selected (default) NAND device (MT29F4G08AB) on these boards has: - data-width=8bits - blocksize=256KB - pagesize=4KB - oobsize=224 bytes For above NAND device, ROM code expects the boot-loader to be flashed in BCH16 ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs. Signed-off-by: Pekon Gupta --- board/ti/am43xx/board.c | 1 + board/ti/am43xx/mux.c | 43 ++++++++++++++++++++++++++++++++++++++++++- 2 files changed, 43 insertions(+), 1 deletion(-) (limited to 'board/ti') diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c index 51fa9e0..a1c3c17 100644 --- a/board/ti/am43xx/board.c +++ b/board/ti/am43xx/board.c @@ -626,6 +626,7 @@ int board_init(void) modena_init0_bw_integer, modena_init0_watermark_0; gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + gpmc_init(); /* Clear all important bits for DSS errata that may need to be tweaked*/ mreqprio_0 = readl(&cdev->mreqprio_0) & MREQPRIO_0_SAB_INIT1_MASK & diff --git a/board/ti/am43xx/mux.c b/board/ti/am43xx/mux.c index 50967e1..a670b0b 100644 --- a/board/ti/am43xx/mux.c +++ b/board/ti/am43xx/mux.c @@ -73,7 +73,38 @@ static struct module_pin_mux gpio5_7_pin_mux[] = { {-1}, }; -static struct module_pin_mux qspi_pin_mux[] = { +#ifdef CONFIG_NAND +static struct module_pin_mux nand_pin_mux[] = { + {OFFSET(gpmc_ad0), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD0 */ + {OFFSET(gpmc_ad1), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD1 */ + {OFFSET(gpmc_ad2), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD2 */ + {OFFSET(gpmc_ad3), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD3 */ + {OFFSET(gpmc_ad4), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD4 */ + {OFFSET(gpmc_ad5), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD5 */ + {OFFSET(gpmc_ad6), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD6 */ + {OFFSET(gpmc_ad7), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD7 */ +#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT + {OFFSET(gpmc_ad8), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD8 */ + {OFFSET(gpmc_ad9), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD9 */ + {OFFSET(gpmc_ad10), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD10 */ + {OFFSET(gpmc_ad11), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD11 */ + {OFFSET(gpmc_ad12), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD12 */ + {OFFSET(gpmc_ad13), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD13 */ + {OFFSET(gpmc_ad14), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD14 */ + {OFFSET(gpmc_ad15), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD15 */ +#endif + {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* Wait */ + {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN)}, /* Write Protect */ + {OFFSET(gpmc_csn0), (MODE(0) | PULLUP_EN)}, /* Chip-Select */ + {OFFSET(gpmc_wen), (MODE(0) | PULLDOWN_EN)}, /* Write Enable */ + {OFFSET(gpmc_oen_ren), (MODE(0) | PULLDOWN_EN)}, /* Read Enable */ + {OFFSET(gpmc_advn_ale), (MODE(0) | PULLDOWN_EN)}, /* Addr Latch Enable*/ + {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLDOWN_EN)}, /* Byte Enable */ + {-1}, +}; +#endif + +static __maybe_unused struct module_pin_mux qspi_pin_mux[] = { {OFFSET(gpmc_csn0), (MODE(3) | PULLUP_EN | RXACTIVE)}, /* QSPI_CS0 */ {OFFSET(gpmc_csn3), (MODE(2) | PULLUP_EN | RXACTIVE)}, /* QSPI_CLK */ {OFFSET(gpmc_advn_ale), (MODE(3) | PULLUP_EN | RXACTIVE)}, /* QSPI_D0 */ @@ -97,12 +128,22 @@ void enable_board_pin_mux(void) if (board_is_gpevm()) { configure_module_pin_mux(gpio5_7_pin_mux); configure_module_pin_mux(rgmii1_pin_mux); +#if defined(CONFIG_NAND) + configure_module_pin_mux(nand_pin_mux); +#endif } else if (board_is_sk()) { configure_module_pin_mux(rgmii1_pin_mux); +#if defined(CONFIG_NAND) + printf("Error: NAND flash not present on this board\n"); +#endif configure_module_pin_mux(qspi_pin_mux); } else if (board_is_eposevm()) { configure_module_pin_mux(rmii1_pin_mux); +#if defined(CONFIG_NAND) + configure_module_pin_mux(nand_pin_mux); +#else configure_module_pin_mux(qspi_pin_mux); +#endif } } -- cgit v1.1 From 54a97d2849979acd84a0475486edf0d0c18e47c7 Mon Sep 17 00:00:00 2001 From: pekon gupta Date: Tue, 22 Jul 2014 16:03:23 +0530 Subject: board/ti/dra7xx: add support for parallel NAND This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC chip-select[0] on DRA7xx EVM. As GPMC pins are shared by multiple devices, so in addition to this patch following board settings are required for NAND device detection [1]: SW5.9 (GPMC_WPN) = OFF (logic-1) SW5.1 (NAND_BOOTn) = ON (logic-0) /* Active-low */ SW5.2 (NOR_BOOTn) = OFF (logic-1) SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations SW2.1 (SYSBOOT[0]) = ON (logic-1) /* selects NAND Boot */ SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */ SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */ SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */ SW2.5 (SYSBOOT[4]) = ON (logic-1) /* selects NAND Boot */ SW2.6 (SYSBOOT[5]) = ON (logic-1) /* selects NAND Boot */ SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */ SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */ SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */ SW3.5 (SYSBOOT[12])= ON (logic-1) /* device type: Addr/Data Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Following changes are required in board.cfg to enable NAND on J6-EVM: --- board/ti/dra7xx/mux_data.h | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) (limited to 'board/ti') diff --git a/board/ti/dra7xx/mux_data.h b/board/ti/dra7xx/mux_data.h index 7db7032..1ea236b 100644 --- a/board/ti/dra7xx/mux_data.h +++ b/board/ti/dra7xx/mux_data.h @@ -68,6 +68,33 @@ const struct pad_conf_entry core_padconf_array_essential[] = { {VIN2A_D21, (IEN | M3)}, {VIN2A_D22, (IEN | M3)}, {VIN2A_D23, (IEN | M3)}, +#ifdef CONFIG_NAND + /* NAND / NOR pin-mux */ + {GPMC_AD0 , M0 | IEN | PDIS}, /* GPMC_AD0 */ + {GPMC_AD1 , M0 | IEN | PDIS}, /* GPMC_AD1 */ + {GPMC_AD2 , M0 | IEN | PDIS}, /* GPMC_AD2 */ + {GPMC_AD3 , M0 | IEN | PDIS}, /* GPMC_AD3 */ + {GPMC_AD4 , M0 | IEN | PDIS}, /* GPMC_AD4 */ + {GPMC_AD5 , M0 | IEN | PDIS}, /* GPMC_AD5 */ + {GPMC_AD6 , M0 | IEN | PDIS}, /* GPMC_AD6 */ + {GPMC_AD7 , M0 | IEN | PDIS}, /* GPMC_AD7 */ + {GPMC_AD8 , M0 | IEN | PDIS}, /* GPMC_AD8 */ + {GPMC_AD9 , M0 | IEN | PDIS}, /* GPMC_AD9 */ + {GPMC_AD10, M0 | IEN | PDIS}, /* GPMC_AD10 */ + {GPMC_AD11, M0 | IEN | PDIS}, /* GPMC_AD11 */ + {GPMC_AD12, M0 | IEN | PDIS}, /* GPMC_AD12 */ + {GPMC_AD13, M0 | IEN | PDIS}, /* GPMC_AD13 */ + {GPMC_AD14, M0 | IEN | PDIS}, /* GPMC_AD14 */ + {GPMC_AD15, M0 | IEN | PDIS}, /* GPMC_AD15 */ + {GPMC_CS0, M0 | IDIS | PEN | PTU}, /* GPMC chip-select */ + {GPMC_ADVN_ALE, M0 | IDIS | PEN | PTD}, /* GPMC Addr latch */ + {GPMC_OEN_REN, M0 | IDIS | PEN | PTU}, /* GPMC Read enable */ + {GPMC_WEN, M0 | IDIS | PEN | PTU}, /* GPMC Write enable_n */ + {GPMC_BEN0, M0 | IDIS | PEN | PTD}, /* GPMC Byte/Column En */ + {GPMC_WAIT0, M0 | IEN | PEN | PTU}, /* GPMC Wait/Ready */ + /* GPMC_WPN (Write Protect) is controlled by DIP Switch SW10(12) */ +#else + /* QSPI pin-mux */ {GPMC_A13, (IEN | PDIS | M1)}, /* QSPI1_RTCLK */ {GPMC_A14, (IEN | PDIS | M1)}, /* QSPI1_D[3] */ {GPMC_A15, (IEN | PDIS | M1)}, /* QSPI1_D[2] */ @@ -78,6 +105,7 @@ const struct pad_conf_entry core_padconf_array_essential[] = { {GPMC_A4, (IEN | PDIS | M1)}, /* QSPI1_CS3 */ {GPMC_CS2, (IEN | PTU | PDIS | M1)}, /* QSPI1_CS0 */ {GPMC_CS3, (IEN | PTU | PDIS | M1)}, /* QSPI1_CS1*/ +#endif /* CONFIG_NAND */ {USB2_DRVVBUS, (M0 | IEN | FSC) }, }; #endif /* _MUX_DATA_DRA7XX_H_ */ -- cgit v1.1 From 9352697aa060e9b1b5d891e4490fdfa6f5ba6114 Mon Sep 17 00:00:00 2001 From: pekon gupta Date: Tue, 22 Jul 2014 16:03:24 +0530 Subject: board/ti/dra7xx: add support for parallel NOR This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM. The Flash device is connected to GPMC controller on chip-select[0] and accessed as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and is CFI compatible. As multiple devices are share GPMC pins on this board, so following board settings are required to detect NOR device: SW5.1 (NAND_BOOTn) = OFF (logic-1) SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */ SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations: SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */ SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Also, following changes are required to enable NOR Flash support in dra7xx_evm board profile: --- board/ti/dra7xx/mux_data.h | 36 ++++++++++++++++++++++++++++++++++-- 1 file changed, 34 insertions(+), 2 deletions(-) (limited to 'board/ti') diff --git a/board/ti/dra7xx/mux_data.h b/board/ti/dra7xx/mux_data.h index 1ea236b..5bc4fc9 100644 --- a/board/ti/dra7xx/mux_data.h +++ b/board/ti/dra7xx/mux_data.h @@ -21,6 +21,37 @@ const struct pad_conf_entry core_padconf_array_essential[] = { {MMC1_DAT3, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT3 */ {MMC1_SDCD, (FSC | IEN | PTU | PDIS | M0)}, /* MMC1_SDCD */ {MMC1_SDWP, (FSC | IEN | PTD | PEN | M14)}, /* MMC1_SDWP */ +#if defined(CONFIG_NOR) + /* NOR only pin-mux */ + {GPMC_A0 , M0 | IDIS | PDIS}, /* nor.GPMC_A[0 ] */ + {GPMC_A1 , M0 | IDIS | PDIS}, /* nor.GPMC_A[1 ] */ + {GPMC_A2 , M0 | IDIS | PDIS}, /* nor.GPMC_A[2 ] */ + {GPMC_A3 , M0 | IDIS | PDIS}, /* nor.GPMC_A[3 ] */ + {GPMC_A4 , M0 | IDIS | PDIS}, /* nor.GPMC_A[4 ] */ + {GPMC_A5 , M0 | IDIS | PDIS}, /* nor.GPMC_A[5 ] */ + {GPMC_A6 , M0 | IDIS | PDIS}, /* nor.GPMC_A[6 ] */ + {GPMC_A7 , M0 | IDIS | PDIS}, /* nor.GPMC_A[7 ] */ + {GPMC_A8 , M0 | IDIS | PDIS}, /* nor.GPMC_A[8 ] */ + {GPMC_A9 , M0 | IDIS | PDIS}, /* nor.GPMC_A[9 ] */ + {GPMC_A10 , M0 | IDIS | PDIS}, /* nor.GPMC_A[10] */ + {GPMC_A11 , M0 | IDIS | PDIS}, /* nor.GPMC_A[11] */ + {GPMC_A12 , M0 | IDIS | PDIS}, /* nor.GPMC_A[12] */ + {GPMC_A13 , M0 | IDIS | PDIS}, /* nor.GPMC_A[13] */ + {GPMC_A14 , M0 | IDIS | PDIS}, /* nor.GPMC_A[14] */ + {GPMC_A15 , M0 | IDIS | PDIS}, /* nor.GPMC_A[15] */ + {GPMC_A16 , M0 | IDIS | PDIS}, /* nor.GPMC_A[16] */ + {GPMC_A17 , M0 | IDIS | PDIS}, /* nor.GPMC_A[17] */ + {GPMC_A18 , M0 | IDIS | PDIS}, /* nor.GPMC_A[18] */ + {GPMC_A19 , M0 | IDIS | PDIS}, /* nor.GPMC_A[19] */ + {GPMC_A20 , M0 | IDIS | PDIS}, /* nor.GPMC_A[20] */ + {GPMC_A21 , M0 | IDIS | PDIS}, /* nor.GPMC_A[21] */ + {GPMC_A22 , M0 | IDIS | PDIS}, /* nor.GPMC_A[22] */ + {GPMC_A23 , M0 | IDIS | PDIS}, /* nor.GPMC_A[23] */ + {GPMC_A24 , M0 | IDIS | PDIS}, /* nor.GPMC_A[24] */ + {GPMC_A25 , M0 | IDIS | PDIS}, /* nor.GPMC_A[25] */ + {GPMC_A26 , M0 | IDIS | PDIS}, /* nor.GPMC_A[26] */ +#else + /* eMMC pinmux */ {GPMC_A19, (IEN | PTU | PDIS | M1)}, /* mmc2_dat4 */ {GPMC_A20, (IEN | PTU | PDIS | M1)}, /* mmc2_dat5 */ {GPMC_A21, (IEN | PTU | PDIS | M1)}, /* mmc2_dat6 */ @@ -31,6 +62,7 @@ const struct pad_conf_entry core_padconf_array_essential[] = { {GPMC_A26, (IEN | PTU | PDIS | M1)}, /* mmc2_dat2 */ {GPMC_A27, (IEN | PTU | PDIS | M1)}, /* mmc2_dat3 */ {GPMC_CS1, (IEN | PTU | PDIS | M1)}, /* mmm2_cmd */ +#endif #if (CONFIG_CONS_INDEX == 1) {UART1_RXD, (FSC | IEN | PTU | PDIS | M0)}, /* UART1_RXD */ {UART1_TXD, (FSC | IEN | PTU | PDIS | M0)}, /* UART1_TXD */ @@ -68,7 +100,7 @@ const struct pad_conf_entry core_padconf_array_essential[] = { {VIN2A_D21, (IEN | M3)}, {VIN2A_D22, (IEN | M3)}, {VIN2A_D23, (IEN | M3)}, -#ifdef CONFIG_NAND +#if defined(CONFIG_NAND) || defined(CONFIG_NOR) /* NAND / NOR pin-mux */ {GPMC_AD0 , M0 | IEN | PDIS}, /* GPMC_AD0 */ {GPMC_AD1 , M0 | IEN | PDIS}, /* GPMC_AD1 */ @@ -105,7 +137,7 @@ const struct pad_conf_entry core_padconf_array_essential[] = { {GPMC_A4, (IEN | PDIS | M1)}, /* QSPI1_CS3 */ {GPMC_CS2, (IEN | PTU | PDIS | M1)}, /* QSPI1_CS0 */ {GPMC_CS3, (IEN | PTU | PDIS | M1)}, /* QSPI1_CS1*/ -#endif /* CONFIG_NAND */ +#endif /* CONFIG_NAND || CONFIG_NOR */ {USB2_DRVVBUS, (M0 | IEN | FSC) }, }; #endif /* _MUX_DATA_DRA7XX_H_ */ -- cgit v1.1 From 61f66fd5a81b97478e9d14326c1059baa6626680 Mon Sep 17 00:00:00 2001 From: Vitaly Andrianov Date: Fri, 25 Jul 2014 22:23:19 +0300 Subject: keystone2: use EFUSE_BOOTROM information to configure PLLs This patch reads EFUSE_BOOTROM register to see the maximum supported clock for CORE and TETRIS PLLs and configure them accordingly. Acked-by: Murali Karicheri Signed-off-by: Vitaly Andrianov Signed-off-by: Ivan Khoronzhuk --- board/ti/ks2_evm/board_k2e.c | 23 +++++++++++++++++++---- board/ti/ks2_evm/board_k2hk.c | 29 +++++++++++++++++++++++++---- 2 files changed, 44 insertions(+), 8 deletions(-) (limited to 'board/ti') diff --git a/board/ti/ks2_evm/board_k2e.c b/board/ti/ks2_evm/board_k2e.c index d2499b7..5472a43 100644 --- a/board/ti/ks2_evm/board_k2e.c +++ b/board/ti/ks2_evm/board_k2e.c @@ -25,15 +25,30 @@ unsigned int external_clk[ext_clk_count] = { [usb_clk] = 100000000, }; -static struct pll_init_data pll_config[] = { - CORE_PLL_1200, - PASS_PLL_1000, +static struct pll_init_data core_pll_config[] = { + CORE_PLL_800, + CORE_PLL_850, + CORE_PLL_1000, + CORE_PLL_1250, + CORE_PLL_1350, + CORE_PLL_1400, + CORE_PLL_1500, }; + +static struct pll_init_data pa_pll_config = + PASS_PLL_1000; + #if defined(CONFIG_BOARD_EARLY_INIT_F) int board_early_init_f(void) { - init_plls(ARRAY_SIZE(pll_config), pll_config); + int speed; + + speed = get_max_dev_speed(); + init_pll(&core_pll_config[speed]); + + init_pll(&pa_pll_config); + return 0; } #endif diff --git a/board/ti/ks2_evm/board_k2hk.c b/board/ti/ks2_evm/board_k2hk.c index a369d6b..6fb3d21 100644 --- a/board/ti/ks2_evm/board_k2hk.c +++ b/board/ti/ks2_evm/board_k2hk.c @@ -8,6 +8,7 @@ */ #include +#include #include #include @@ -28,12 +29,23 @@ unsigned int external_clk[ext_clk_count] = { [rp1_clk] = 123456789 }; -static struct pll_init_data pll_config[] = { - CORE_PLL_1228, - PASS_PLL_983, +static struct pll_init_data core_pll_config[] = { + CORE_PLL_799, + CORE_PLL_999, + CORE_PLL_1200, +}; + +static struct pll_init_data tetris_pll_config[] = { + TETRIS_PLL_800, + TETRIS_PLL_1000, TETRIS_PLL_1200, + TETRIS_PLL_1350, + TETRIS_PLL_1400, }; +static struct pll_init_data pa_pll_config = + PASS_PLL_983; + #ifdef CONFIG_DRIVER_TI_KEYSTONE_NET struct eth_priv_t eth_priv_cfg[] = { { @@ -75,7 +87,16 @@ int get_num_eth_ports(void) #ifdef CONFIG_BOARD_EARLY_INIT_F int board_early_init_f(void) { - init_plls(ARRAY_SIZE(pll_config), pll_config); + int speed; + + speed = get_max_dev_speed(); + init_pll(&core_pll_config[speed]); + + init_pll(&pa_pll_config); + + speed = get_max_arm_speed(); + init_pll(&tetris_pll_config[speed]); + return 0; } #endif -- cgit v1.1 From 1286b7f6ca5fc3d42927cbe2f50b51a4870021dd Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Fri, 1 Aug 2014 09:53:24 -0400 Subject: am335x_evm: Convert CONFIG_CONS_INDEX into a menu choice - Drop CONFIG_SERIAL[1-6] and use CONFIG_CONS_INDEX tests instead - Add choice and help text to board/ti/am335x/Kconfig - Correct comment about IDK in board/ti/am335x/mux.c - Remove am335x_evm_uart* defconfig files as they're just variations on a config option now. Signed-off-by: Tom Rini --- board/ti/am335x/Kconfig | 9 +++++++++ board/ti/am335x/board.c | 19 +++++++------------ board/ti/am335x/mux.c | 7 +------ 3 files changed, 17 insertions(+), 18 deletions(-) (limited to 'board/ti') diff --git a/board/ti/am335x/Kconfig b/board/ti/am335x/Kconfig index c3b61af..0e5149c 100644 --- a/board/ti/am335x/Kconfig +++ b/board/ti/am335x/Kconfig @@ -20,4 +20,13 @@ config SYS_CONFIG_NAME string default "am335x_evm" +config CONS_INDEX + int "UART used for console" + default 1 + help + The AM335x SoC has a total of 6 UARTs (UART0 to UART5 as referenced + in documentation, etc) available to it. Depending on your specific + board you may want something other than UART0 as for example the IDK + uses UART3 so enter 4 here. + endif diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index d81eec9..0739e60 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -383,24 +383,19 @@ const struct dpll_params *get_dpll_ddr_params(void) void set_uart_mux_conf(void) { -#ifdef CONFIG_SERIAL1 +#if CONFIG_CONS_INDEX == 1 enable_uart0_pin_mux(); -#endif /* CONFIG_SERIAL1 */ -#ifdef CONFIG_SERIAL2 +#elif CONFIG_CONS_INDEX == 2 enable_uart1_pin_mux(); -#endif /* CONFIG_SERIAL2 */ -#ifdef CONFIG_SERIAL3 +#elif CONFIG_CONS_INDEX == 3 enable_uart2_pin_mux(); -#endif /* CONFIG_SERIAL3 */ -#ifdef CONFIG_SERIAL4 +#elif CONFIG_CONS_INDEX == 4 enable_uart3_pin_mux(); -#endif /* CONFIG_SERIAL4 */ -#ifdef CONFIG_SERIAL5 +#elif CONFIG_CONS_INDEX == 5 enable_uart4_pin_mux(); -#endif /* CONFIG_SERIAL5 */ -#ifdef CONFIG_SERIAL6 +#elif CONFIG_CONS_INDEX == 6 enable_uart5_pin_mux(); -#endif /* CONFIG_SERIAL6 */ +#endif } void set_mux_conf_regs(void) diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c index 2a18ccb..f4bb9f8 100644 --- a/board/ti/am335x/mux.c +++ b/board/ti/am335x/mux.c @@ -345,12 +345,7 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) configure_module_pin_mux(spi0_pin_mux); } } else if (board_is_idk(header)) { - /* - * Industrial Motor Control (IDK) - * note: IDK console is on UART3 by default. - * So u-boot mus be build with CONFIG_SERIAL4 and - * CONFIG_CONS_INDEX=4 - */ + /* Industrial Motor Control (IDK) */ configure_module_pin_mux(mii1_pin_mux); configure_module_pin_mux(mmc0_no_cd_pin_mux); } else if (board_is_evm_sk(header)) { -- cgit v1.1 From 7b9225237049181524be5a8801dde6a6716e1357 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Mon, 4 Aug 2014 19:42:24 +0530 Subject: ARM: DRA: Enable VTT regulator DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards, and left unused on previous boards, so it is safe enough to enable gpio on all DRA7 boards. Signed-off-by: Lokesh Vutla --- board/ti/dra7xx/evm.c | 31 +++++++++++++++++++++++++++++++ board/ti/dra7xx/mux_data.h | 1 + 2 files changed, 32 insertions(+) (limited to 'board/ti') diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c index ae50d88..5592fc5 100644 --- a/board/ti/dra7xx/evm.c +++ b/board/ti/dra7xx/evm.c @@ -13,6 +13,8 @@ #include #include #include +#include +#include #include #include #include @@ -26,6 +28,9 @@ DECLARE_GLOBAL_DATA_PTR; +/* GPIO 7_11 */ +#define GPIO_DDR_VTT_EN 203 + const struct omap_sysinfo sysinfo = { "Board: DRA7xx\n" }; @@ -272,3 +277,29 @@ int board_eth_init(bd_t *bis) return ret; } #endif + +#ifdef CONFIG_BOARD_EARLY_INIT_F +/* VTT regulator enable */ +static inline void vtt_regulator_enable(void) +{ + if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL) + return; + + /* Do not enable VTT for DRA722 */ + if (omap_revision() == DRA722_ES1_0) + return; + + /* + * EVM Rev G and later use gpio7_11 for DDR3 termination. + * This is safe enough to do on older revs. + */ + gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); + gpio_direction_output(GPIO_DDR_VTT_EN, 1); +} + +int board_early_init_f(void) +{ + vtt_regulator_enable(); + return 0; +} +#endif diff --git a/board/ti/dra7xx/mux_data.h b/board/ti/dra7xx/mux_data.h index 5bc4fc9..7276014 100644 --- a/board/ti/dra7xx/mux_data.h +++ b/board/ti/dra7xx/mux_data.h @@ -139,5 +139,6 @@ const struct pad_conf_entry core_padconf_array_essential[] = { {GPMC_CS3, (IEN | PTU | PDIS | M1)}, /* QSPI1_CS1*/ #endif /* CONFIG_NAND || CONFIG_NOR */ {USB2_DRVVBUS, (M0 | IEN | FSC) }, + {SPI1_CS1, (PEN | IDIS | M14) }, }; #endif /* _MUX_DATA_DRA7XX_H_ */ -- cgit v1.1