From cfa460adfdefcc30d104e1a9ee44994ee349bb7b Mon Sep 17 00:00:00 2001 From: William Juul Date: Wed, 31 Oct 2007 13:53:06 +0100 Subject: Update MTD to that of Linux 2.6.22.1 A lot changed in the Linux MTD code, since it was last ported from Linux to U-Boot. This patch takes U-Boot NAND support to the level of Linux 2.6.22.1 and will enable support for very large NAND devices (4KB pages) and ease the compatibility between U-Boot and Linux filesystems. This patch is tested on two custom boards with PPC and ARM processors running YAFFS in U-Boot and Linux using gcc-4.1.2 cross compilers. MAKEALL ppc/arm has some issues: * DOC/OneNand/nand_spl is not building (I have not tried porting these parts, and since I do not have any HW and I am not familiar with this code/HW I think its best left to someone else.) Except for the issues mentioned above, I have ported all drivers necessary to run MAKEALL ppc/arm without errors and warnings. Many drivers were trivial to port, but some were not so trivial. The following drivers must be examined carefully and maybe rewritten to some degree: cpu/ppc4xx/ndfc.c cpu/arm926ejs/davinci/nand.c board/delta/nand.c board/zylonite/nand.c Signed-off-by: William Juul Signed-off-by: Stig Olsen Signed-off-by: Scott Wood --- board/sc3/sc3nand.c | 44 ++++++++++++++++++++------------------------ 1 file changed, 20 insertions(+), 24 deletions(-) (limited to 'board/sc3') diff --git a/board/sc3/sc3nand.c b/board/sc3/sc3nand.c index 009567b..2f2e745 100644 --- a/board/sc3/sc3nand.c +++ b/board/sc3/sc3nand.c @@ -39,30 +39,26 @@ static void *sc3_io_base; static void *sc3_control_base = (void *)0xEF600700; -static void sc3_nand_hwcontrol(struct mtd_info *mtd, int cmd) +static void sc3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - switch (cmd) { - case NAND_CTL_SETCLE: - set_bit (SC3_NAND_CLE, sc3_control_base); - break; - case NAND_CTL_CLRCLE: - clear_bit (SC3_NAND_CLE, sc3_control_base); - break; - - case NAND_CTL_SETALE: - set_bit (SC3_NAND_ALE, sc3_control_base); - break; - case NAND_CTL_CLRALE: - clear_bit (SC3_NAND_ALE, sc3_control_base); - break; - - case NAND_CTL_SETNCE: - set_bit (SC3_NAND_CE, sc3_control_base); - break; - case NAND_CTL_CLRNCE: - clear_bit (SC3_NAND_CE, sc3_control_base); - break; + struct nand_chip *this = mtd->priv; + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + set_bit (SC3_NAND_CLE, sc3_control_base); + else + clear_bit (SC3_NAND_CLE, sc3_control_base); + if ( ctrl & NAND_ALE ) + set_bit (SC3_NAND_ALE, sc3_control_base); + else + clear_bit (SC3_NAND_ALE, sc3_control_base); + if ( ctrl & NAND_NCE ) + set_bit (SC3_NAND_CE, sc3_control_base); + else + clear_bit (SC3_NAND_CE, sc3_control_base); } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } static int sc3_nand_dev_ready(struct mtd_info *mtd) @@ -79,14 +75,14 @@ static void sc3_select_chip(struct mtd_info *mtd, int chip) int board_nand_init(struct nand_chip *nand) { - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; sc3_io_base = (void *) CFG_NAND_BASE; /* Set address of NAND IO lines (Using Linear Data Access Region) */ nand->IO_ADDR_R = (void __iomem *) sc3_io_base; nand->IO_ADDR_W = (void __iomem *) sc3_io_base; /* Reference hardware control function */ - nand->hwcontrol = sc3_nand_hwcontrol; + nand->cmd_ctrl = sc3_nand_hwcontrol; nand->dev_ready = sc3_nand_dev_ready; nand->select_chip = sc3_select_chip; return 0; -- cgit v1.1