From 1894dd381124bdbfbdae7cf3a6ca52a8eb1f4421 Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Fri, 27 Jul 2007 11:25:31 +0200 Subject: Add PPC4xx-HCU4 and HCU5 boards: READMEs Signed-off-by: Niklaus Giger --- board/netstal/hcu4/README.txt | 59 ++++++++++++++ board/netstal/hcu5/README.txt | 174 ++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 233 insertions(+) create mode 100644 board/netstal/hcu4/README.txt create mode 100644 board/netstal/hcu5/README.txt (limited to 'board/netstal') diff --git a/board/netstal/hcu4/README.txt b/board/netstal/hcu4/README.txt new file mode 100644 index 0000000..1e9c64a --- /dev/null +++ b/board/netstal/hcu4/README.txt @@ -0,0 +1,59 @@ +HCU4 Configuration Details + +Memory Bank 0 -- Flash chip +--------------------------- + +0xfff00000 - 0xffffffff + +The flash chip is really only 512Kbytes, but the high address bit of +the 1Meg region is ignored, so the flash is replicated through the +region. Thus, this is consistent with a flash base address 0xfff80000. + +The placement at the end is to be consistent with reset behavior, +where the processor itself initially uses this bus to load the branch +vector and start running. + +On-Chip Memory +-------------- + +0xf4000000 - 0xf4000fff + +The 405GPr includes a 4K on-chip memory that can be placed however +software chooses. I choose to place the memory at this address, to +keep it out of the cachable areas. + + +Internal Peripherals +-------------------- + +0xef600300 - 0xef6008ff + +These are scattered various peripherals internal to the PPC405GPr +chip. + +Chip-Select 2: Flash Memory +--------------------------- + +0x70000000 + +Chip-Select 3: CAN Interface +---------------------------- +0x7800000 + + +Chip-Select 4: IMC-bus standard +------------------------------- + +Our IO-Bus (slow version) + + +Chip-Select 5: IMC-bus fast (inactive) +-------------------------------------- + +Our IO-Bus (fast, but not yet use) + + +Memory Bank 1 -- SDRAM +------------------------------------- + +0x00000000 - 0x1ffffff # Default 32 MB diff --git a/board/netstal/hcu5/README.txt b/board/netstal/hcu5/README.txt new file mode 100644 index 0000000..3118da9 --- /dev/null +++ b/board/netstal/hcu5/README.txt @@ -0,0 +1,174 @@ +HCU5 configuration details and startup sequence + +(C) Copyright 2007 Netstal Maschinen AG + Niklaus Giger (Niklaus.Giger@netstal.com) + +TODO: +----- +- Fix error: Waiting for PHY auto negotiation to complete..... TIMEOUT ! + - Does not occur if both EMAC are connected +- Fix RTS/CTS problem (HW?) + CONFIG_SERIAL_MULTI/CONFIG_SERIAL_SOFTWARE_FIFO hangs after + Switching to interrupt driven serial input mode +- Make vxWorks start from u-boot. Possible reasons + - Does vxWorks need an entry for the Machine Check interrupt like this + tlbentry( 0x40000000, SZ_256M, 0, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) ? + +Caveats: +-------- +Errata CHIP_8: Incorrect Write to DDR SDRAM. (was not applied to sequoia.c) +see hcu5.c. + + +Memory Bank 0 -- Flash chip +--------------------------- + +0xfff00000 - 0xffffffff + +The flash chip is really only 512Kbytes, but the high address bit of +the 1Meg region is ignored, so the flash is replicated through the +region. Thus, this is consistent with a flash base address 0xfff80000. + +The placement at the end is to be consistent with reset behavior, +where the processor itself initially uses this bus to load the branch +vector and start running. + +On-Chip Memory +-------------- + +0xe0010000- 0xe0013fff CFG_OCM_BASE +The 440EPx includes a 16K on-chip memory that can be placed however +software chooses. + +Internal Peripherals +-------------------- + +0xef600300 - 0xef6008ff + +These are scattered various peripherals internal to the PPC440EPX +chip. + +Chip-Select 2: Flash Memory +--------------------------- + +Not used + +Chip-Select 3: CAN Interface +---------------------------- +0xc800000: 2 Intel 82527 CAN-Controller + + +Chip-Select 4: IMC-bus standard +------------------------------- + +0xcc00000: Netstal specific IO-Bus + + +Chip-Select 5: IMC-bus fast (inactive) +-------------------------------------- + +0xce00000: Netstal specific IO-Bus (fast, but not yet used) + + +Memory Bank 1 -- DDR2 +------------------------------------- + +0x00000000 - 0xfffffff # Default 256 MB + +PCI ?? + +USB ?? +Only USB_STORAGE is enabled to load vxWorks +from a memory stick. + +System-LEDs ??? (Analog zu HCU4 ???) + +Startup sequence +---------------- + +(cpu/ppc4xx/resetvec.S) +depending on configs option +call _start_440 _start_pci oder _start + +(cpu/ppc4xx/start.S) + +_start_440: + initialize register like + CCR0 + debug + setup interrupt vectors + configure cache regions + clear and setup TLB + enable internal RAM + jump start_ram + which in turn will jump to start +_start: + Clear and set up some registers. + Debug setup + Setup the internal SRAM + Setup the stack in internal SRAM + setup stack pointer (r1) + setup GOT + call cpu_init_f /* run low-level CPU init code (from Flash) */ + + call cpu_init_f + board_init_f: (lib_ppc\board.c) + init_sequence defines a list of function to be called + board_early_init_f: (board/netstal/hcu5/hcu5.c) + We are using Bootstrap-Option A + if CPR0_ICFG_RLI_MASK == 0 then set some registers and reboot + Setup the GPIO pins + Setup the interrupt controller polarities, triggers, etc. + Ethernet, PCI, USB enable + setup BOOT FLASH (Chip timing) + init_baudrate, + serial_init + checkcpu + misc_init_f #ifdef + init_func_i2c #ifdef + post_init_f #ifdef + init_func_ram -> calls init_dram board/netstal/hcu5/sdram.c + (EYE function removed!!) + test_dram call + + * Reserve memory at end of RAM for (top down in that order): + * - kernel log buffer + * - protected RAM + * - LCD framebuffer + * - monitor code + * - board info struct + Save local variables to board info struct + call relocate_code() does not return + relocate_code: (cpu/ppc4xx/start.S) +------------------------------------------------------- +From now on our copy is in RAM and we will run from there, + starting with board_init_r +------------------------------------------------------- + board_init_r: (lib_ppc\board.c) + setup bd function pointers + trap_init + flash_init: (board/netstal/hcu5/flash.c) + /* setup for u-boot erase, update */ + setup bd flash info + cpu_init_r: (cpu/ppc4xx/cpu_init.c) + peripheral chip select in using defines like + CFG_EBC_PB0A, CFG_EBC_PB0C from hcu5.h + mem_malloc_init + malloc_bin_reloc + spi_init (r or f)??? (CFG_ENV_IS_IN_EEPROM) + env_relocated + misc_init_r(bd): (board/netstal/hcu5.c) + ethaddr mit serial number ergänzen + Then we will somehow go into the command loop + +Most of the HW specific code for the HCU5 may be found in +include/configs/hcu5.h +board/netstal/hcu5/* +cpu/ppc4xx/* +lib_ppc/* +include/ppc440.h + +Drivers for serial etc are found under drivers/ + +Don't ask question if you did not look at the README !! +Most CFG_* and CONFIG_* switches are mentioned/explained there. -- cgit v1.1 From ac982ea5a4f2f993efcf52dca122f5a59df047d8 Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Fri, 27 Jul 2007 11:28:44 +0200 Subject: Add PPC4xx-HCU4 and HCU5 boards: make related Signed-off-by: Niklaus Giger --- board/netstal/hcu4/Makefile | 49 ++++++++++++++ board/netstal/hcu4/config.mk | 29 +++++++++ board/netstal/hcu4/u-boot.lds | 140 ++++++++++++++++++++++++++++++++++++++++ board/netstal/hcu5/Makefile | 49 ++++++++++++++ board/netstal/hcu5/config.mk | 31 +++++++++ board/netstal/hcu5/u-boot.lds | 144 ++++++++++++++++++++++++++++++++++++++++++ 6 files changed, 442 insertions(+) create mode 100644 board/netstal/hcu4/Makefile create mode 100644 board/netstal/hcu4/config.mk create mode 100644 board/netstal/hcu4/u-boot.lds create mode 100644 board/netstal/hcu5/Makefile create mode 100644 board/netstal/hcu5/config.mk create mode 100644 board/netstal/hcu5/u-boot.lds (limited to 'board/netstal') diff --git a/board/netstal/hcu4/Makefile b/board/netstal/hcu4/Makefile new file mode 100644 index 0000000..d9825a5 --- /dev/null +++ b/board/netstal/hcu4/Makefile @@ -0,0 +1,49 @@ +# +# (C) Copyright 2007 Netstal Maschinen AG +# Niklaus Giger (ng@netstal.com) +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +vpath flash.c ../common +COBJS = $(BOARD).o flash.o +SOBJS = + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/netstal/hcu4/config.mk b/board/netstal/hcu4/config.mk new file mode 100644 index 0000000..f5a4ce4 --- /dev/null +++ b/board/netstal/hcu4/config.mk @@ -0,0 +1,29 @@ +# +# (C) Copyright 2005 Netstal Maschinen AG +# Niklaus Giger (ng@netstal.com) +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# Netstal Maschinen AG: HCU4 boards +# + +TEXT_BASE = 0xFFFa0000 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG -g +endif + diff --git a/board/netstal/hcu4/u-boot.lds b/board/netstal/hcu4/u-boot.lds new file mode 100644 index 0000000..b6e28f8 --- /dev/null +++ b/board/netstal/hcu4/u-boot.lds @@ -0,0 +1,140 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : { + /* The start.o file includes the initial jump vector that + must be located in the beginning. It is the basic run- + time function that calls all other functions. */ + cpu/ppc4xx/start.o (.text) + +/* . = env_offset;*/ +/* common/environment.o(.text)*/ + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/netstal/hcu5/Makefile b/board/netstal/hcu5/Makefile new file mode 100644 index 0000000..eee310b --- /dev/null +++ b/board/netstal/hcu5/Makefile @@ -0,0 +1,49 @@ +# +# (C) Copyright 2007 Netstal Maschinen AG +# Niklaus Giger (ng@netstal.com) +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +vpath flash.c ../common +COBJS = $(BOARD).o sdram.o flash.o +SOBJS = init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/netstal/hcu5/config.mk b/board/netstal/hcu5/config.mk new file mode 100644 index 0000000..58ec2af --- /dev/null +++ b/board/netstal/hcu5/config.mk @@ -0,0 +1,31 @@ +# +# (C) Copyright 2005 Netstal Maschinen AG +# Niklaus Giger (ng@netstal.com) +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# Netstal Maschinen AG: HCU5 boards +# + +TEXT_BASE = 0xFFFa0000 + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG -g +endif + diff --git a/board/netstal/hcu5/u-boot.lds b/board/netstal/hcu5/u-boot.lds new file mode 100644 index 0000000..6d255a9 --- /dev/null +++ b/board/netstal/hcu5/u-boot.lds @@ -0,0 +1,144 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); + +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/ppc4xx/start.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/ppc4xx/start.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + + ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); + + _end = . ; + PROVIDE (end = .); +} -- cgit v1.1 From e8397fc78c9394d71de233a4d810fbc9047e4c76 Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Fri, 27 Jul 2007 11:38:26 +0200 Subject: Add PPC4xx-HCU4 and HCU5 boards: common files Signed-off-by: Niklaus Giger --- board/netstal/common/flash.c | 528 ++++++++++++++++++++++++++++++++++++++++++ board/netstal/common/nm_bsp.c | 42 ++++ 2 files changed, 570 insertions(+) create mode 100644 board/netstal/common/flash.c create mode 100644 board/netstal/common/nm_bsp.c (limited to 'board/netstal') diff --git a/board/netstal/common/flash.c b/board/netstal/common/flash.c new file mode 100644 index 0000000..be2cb37 --- /dev/null +++ b/board/netstal/common/flash.c @@ -0,0 +1,528 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Modified 4/5/2001 + * Wait for completion of each sector erase command issued + * 4/5/2001 + * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com + * + * Modified 6/6/2007 + * Added isync + * Niklaus Giger, Netstal Maschinen, niklaus.giger@netstal.com + * + */ + +#include +#include +#include + +#if CFG_MAX_FLASH_BANKS != 1 +#error "CFG_MAX_FLASH_BANKS must be 1" +#endif +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +/*----------------------------------------------------------------------- + * Functions + */ +static ulong flash_get_size (vu_long * addr, flash_info_t * info); +static int write_word (flash_info_t * info, ulong dest, ulong data); +static void flash_get_offsets (ulong base, flash_info_t * info); + +#define ADDR0 0x5555 +#define ADDR1 0x2aaa +#define FLASH_WORD_SIZE unsigned char + +/*-----------------------------------------------------------------------*/ + +unsigned long flash_init (void) +{ + unsigned long size_b0; + + /* Init: no FLASHes known */ + flash_info[0].flash_id = FLASH_UNKNOWN; + + /* Static FLASH Bank configuration here - FIXME XXX */ + + size_b0 = flash_get_size ((vu_long *) FLASH_BASE0_PRELIM, + &flash_info[0]); + + if (flash_info[0].flash_id == FLASH_UNKNOWN) { + printf ("## Unknown FLASH on Bank 0- Size=0x%08lx=%ld MB\n", + size_b0, size_b0 << 20); + } + + /* Only one bank */ + /* Setup offsets */ + flash_get_offsets (FLASH_BASE0_PRELIM, &flash_info[0]); + + /* Monitor protection ON by default */ + (void) flash_protect (FLAG_PROTECT_SET, + FLASH_BASE0_PRELIM, + FLASH_BASE0_PRELIM + monitor_flash_len - 1, + &flash_info[0]); + flash_info[0].size = size_b0; + + return size_b0; +} + + +/*-----------------------------------------------------------------------*/ +/* + * This implementation assumes that the flash chips are uniform sector + * devices. This is true for all likely flash devices on a HCUx. + */ +static void flash_get_offsets (ulong base, flash_info_t * info) +{ + unsigned idx; + unsigned long sector_size = info->size / info->sector_count; + + for (idx = 0; idx < info->sector_count; idx += 1) { + info->start[idx] = base + (idx * sector_size); + } +} + +/*-----------------------------------------------------------------------*/ +void flash_print_info (flash_info_t * info) +{ + int i; + int k; + int size; + int erased; + volatile unsigned long *flash; + + if (info->flash_id == FLASH_UNKNOWN) { + printf ("missing or unknown FLASH type\n"); + return; + } + + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_AMD: + printf ("AMD "); + break; + case FLASH_MAN_FUJ: + printf ("FUJITSU "); + break; + case FLASH_MAN_SST: + printf ("SST "); + break; + case FLASH_MAN_STM: + printf ("ST Micro "); + break; + default: + printf ("Unknown Vendor "); + break; + } + + /* (Reduced table of only parts expected in HCUx boards.) */ + switch (info->flash_id) { + case FLASH_MAN_AMD | FLASH_AM040: + printf ("AM29F040 (512 Kbit, uniform sector size)\n"); + break; + case FLASH_MAN_STM | FLASH_AM040: + printf ("MM29W040W (512 Kbit, uniform sector size)\n"); + break; + default: + printf ("Unknown Chip Type\n"); + break; + } + + printf (" Size: %ld KB in %d Sectors\n", + info->size >> 10, info->sector_count); + + printf (" Sector Start Addresses:"); + for (i = 0; i < info->sector_count; ++i) { + /* + * Check if whole sector is erased + */ + if (i != (info->sector_count - 1)) + size = info->start[i + 1] - info->start[i]; + else + size = info->start[0] + info->size - info->start[i]; + erased = 1; + flash = (volatile unsigned long *) info->start[i]; + size = size >> 2; /* divide by 4 for longword access */ + for (k = 0; k < size; k++) { + if (*flash++ != 0xffffffff) { + erased = 0; + break; + } + } + + if ((i % 5) == 0) + printf ("\n "); + printf (" %08lX%s%s", + info->start[i], + erased ? " E" : " ", info->protect[i] ? "RO " : " " + ); + } + printf ("\n"); + return; +} + +/*-----------------------------------------------------------------------*/ + +/* + * The following code cannot be run from FLASH! + */ +static ulong flash_get_size (vu_long * addr, flash_info_t * info) +{ + short i; + FLASH_WORD_SIZE value; + ulong base = (ulong) addr; + volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) addr; + + /* Write auto select command: read Manufacturer ID */ + asm("isync"); + addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; + asm("isync"); + addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; + asm("isync"); + addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00900090; + asm("isync"); + + value = addr2[0]; + asm("isync"); + + switch (value) { + case (FLASH_WORD_SIZE) AMD_MANUFACT: + info->flash_id = FLASH_MAN_AMD; + break; + case (FLASH_WORD_SIZE) FUJ_MANUFACT: + info->flash_id = FLASH_MAN_FUJ; + break; + case (FLASH_WORD_SIZE) SST_MANUFACT: + info->flash_id = FLASH_MAN_SST; + break; + case (FLASH_WORD_SIZE)STM_MANUFACT: + info->flash_id = FLASH_MAN_STM; + break; + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + printf("Unknown flash manufacturer code: 0x%x at %p\n", + value, addr); + addr2[ADDR0] = (FLASH_WORD_SIZE) 0; + return (0); /* no or unknown flash */ + } + + value = addr2[1]; /* device ID */ + + switch (value) { + case (FLASH_WORD_SIZE) AMD_ID_F040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + case (FLASH_WORD_SIZE) AMD_ID_LV040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + case (FLASH_WORD_SIZE)STM_ID_M29W040B: /* most likele HCU5 chip */ + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + default: + info->flash_id = FLASH_UNKNOWN; + return (0); /* => no or unknown flash */ + + } + + /* Calculate the sector offsets (Use HCUx Optimized code). */ + flash_get_offsets(base, info); + + /* check for protected sectors */ + for (i = 0; i < info->sector_count; i++) { + /* read sector protection at sector address, + *(A7 .. A0) = 0x02 + * D0 = 1 if protected + */ + addr2 = (volatile FLASH_WORD_SIZE *) (info->start[i]); + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) + info->protect[i] = 0; + else + info->protect[i] = addr2[2] & 1; + } + + /* + * Prevent writes to uninitialized FLASH. + */ + if (info->flash_id != FLASH_UNKNOWN) { + addr2 = (FLASH_WORD_SIZE *) info->start[0]; + *addr2 = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ + } + + return (info->size); +} + +int wait_for_DQ7 (flash_info_t * info, int sect) +{ + ulong start, now, last; + volatile FLASH_WORD_SIZE *addr = + (FLASH_WORD_SIZE *) (info->start[sect]); + + start = get_timer (0); + last = start; + while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) != + (FLASH_WORD_SIZE) 0x00800080) { + if ((now = get_timer (start)) > CFG_FLASH_ERASE_TOUT) { + printf ("Timeout\n"); + return -1; + } + /* show that we're waiting */ + if ((now - last) > 1000) { /* every second */ + putc ('.'); + last = now; + } + } + return 0; +} + +/*-----------------------------------------------------------------------*/ + +int flash_erase (flash_info_t * info, int s_first, int s_last) +{ + volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]); + volatile FLASH_WORD_SIZE *addr2; + int flag, prot, sect, l_sect; + int i; + + if ((s_first < 0) || (s_first > s_last)) { + if (info->flash_id == FLASH_UNKNOWN) { + printf ("- missing\n"); + } else { + printf ("- no sectors to erase\n"); + } + return 1; + } + + if (info->flash_id == FLASH_UNKNOWN) { + printf ("Can't erase unknown flash type - aborted\n"); + return 1; + } + + prot = 0; + for (sect = s_first; sect <= s_last; ++sect) { + if (info->protect[sect]) { + prot++; + } + } + + if (prot) { + printf ("- Warning: %d protected sectors not erased!\n", + prot); + } else { + printf ("\n"); + } + + l_sect = -1; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts (); + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect <= s_last; sect++) { + if (info->protect[sect] == 0) { /* not protected */ + addr2 = (FLASH_WORD_SIZE *) (info->start[sect]); + printf ("Erasing sector %p\n", addr2); /* CLH */ + + if ((info->flash_id & FLASH_VENDMASK) == + FLASH_MAN_SST) { + addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; + addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; + addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080; + addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; + addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; + /* block erase */ + addr2[0] = (FLASH_WORD_SIZE) 0x00500050; + for (i = 0; i < 50; i++) udelay (1000); + } else { + addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; + addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; + addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080; + addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; + addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; + /* sector erase */ + addr2[0] = (FLASH_WORD_SIZE) 0x00300030; + } + l_sect = sect; + /* + * Wait for each sector to complete, it's more + * reliable. According to AMD Spec, you must + * issue all erase commands within a specified + * timeout. This has been seen to fail, especially + * if printf()s are included (for debug)!! + */ + wait_for_DQ7 (info, sect); + } + } + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts (); + + /* wait at least 80us - let's wait 1 ms */ + udelay (1000); + +#if 0 + /* + * We wait for the last triggered sector + */ + if (l_sect < 0) + goto DONE; + wait_for_DQ7 (info, l_sect); + +DONE: +#endif + /* reset to read mode */ + addr = (FLASH_WORD_SIZE *) info->start[0]; + addr[0] = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ + + printf (" done\n"); + return 0; +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ + +int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) +{ + ulong cp, wp, data; + int i, l, rc; + + wp = (addr & ~3); /* get lower word aligned address */ + + /* + * handle unaligned start bytes + */ + if ((l = addr - wp) != 0) { + data = 0; + for (i = 0, cp = wp; i < l; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + for (; i < 4 && cnt > 0; ++i) { + data = (data << 8) | *src++; + --cnt; + ++cp; + } + for (; cnt == 0 && i < 4; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + if ((rc = write_word (info, wp, data)) != 0) { + return (rc); + } + wp += 4; + } + + /* + * handle word aligned part + */ + while (cnt >= 4) { + data = 0; + for (i = 0; i < 4; ++i) { + data = (data << 8) | *src++; + } + if ((rc = write_word (info, wp, data)) != 0) { + return (rc); + } + wp += 4; + cnt -= 4; + } + + if (cnt == 0) { + return (0); + } + + /* + * handle unaligned tail bytes + */ + data = 0; + for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) { + data = (data << 8) | *src++; + --cnt; + } + for (; i < 4; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + return (write_word (info, wp, data)); +} + +/*----------------------------------------------------------------------- + * Write a word to Flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int write_word (flash_info_t * info, ulong dest, ulong data) +{ + volatile FLASH_WORD_SIZE *addr2 = + (FLASH_WORD_SIZE *) (info->start[0]); + volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *) dest; + volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data; + ulong start; + int i; + + /* Check if Flash is (sufficiently) erased */ + if ((*((volatile FLASH_WORD_SIZE *) dest) & + (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) { + return (2); + } + + for (i = 0; i < 4 / sizeof (FLASH_WORD_SIZE); i++) { + int flag; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts (); + + addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; + addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; + addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00A000A0; + + dest2[i] = data2[i]; + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts (); + + /* data polling for D7 */ + start = get_timer (0); + while ((dest2[i] & (FLASH_WORD_SIZE) 0x00800080) != + (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) { + + if (get_timer (start) > CFG_FLASH_WRITE_TOUT) { + return (1); + } + } + } + + return (0); +} diff --git a/board/netstal/common/nm_bsp.c b/board/netstal/common/nm_bsp.c new file mode 100644 index 0000000..ee1b684 --- /dev/null +++ b/board/netstal/common/nm_bsp.c @@ -0,0 +1,42 @@ +/* + *(C) Copyright 2005-2007 Netstal Maschinen AG + * Niklaus Giger (Niklaus.Giger@netstal.com) + * + * This source code is free software; you can redistribute it + * and/or modify it in source code form under the terms of the GNU + * General Public License as published by the Free Software + * Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA + */ + +#include +#include + +#if (CONFIG_COMMANDS & CFG_CMD_BSP) +/* + * Command nm_bsp: Netstal Maschinen BSP specific command + */ +int nm_bsp(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + printf("%s: flag %d, argc %d, argv[0] %s\n", __FUNCTION__, + flag, argc, argv[0]); + printf("Netstal Maschinen BSP specific command. None at the moment.\n"); + return 0; +} + +U_BOOT_CMD( + nm_bsp, 1, 1, nm_bsp, + "nm_bsp - Netstal Maschinen BSP specific command. \n", + "Help for Netstal Maschinen BSP specific command.\n" + ); +#endif + -- cgit v1.1 From 6e5de26c6e7580faf16e87745cd488b92b492d0c Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Fri, 27 Jul 2007 11:30:33 +0200 Subject: Add PPC4xx-HCU4 and HCU5 boards: HCU4 files Signed-off-by: Niklaus Giger --- board/netstal/hcu4/hcu4.c | 393 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 393 insertions(+) create mode 100644 board/netstal/hcu4/hcu4.c (limited to 'board/netstal') diff --git a/board/netstal/hcu4/hcu4.c b/board/netstal/hcu4/hcu4.c new file mode 100644 index 0000000..deb7d2d --- /dev/null +++ b/board/netstal/hcu4/hcu4.c @@ -0,0 +1,393 @@ +/* + *(C) Copyright 2005-2007 Netstal Maschinen AG + * Niklaus Giger (Niklaus.Giger@netstal.com) + * + * This source code is free software; you can redistribute it + * and/or modify it in source code form under the terms of the GNU + * General Public License as published by the Free Software + * Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA + */ + +#include +#include +#include +#include +#include +#include "../common/nm_bsp.c" + +DECLARE_GLOBAL_DATA_PTR; + +void sysLedSet(u32 value); +long int spd_sdram(int(read_spd)(uint addr)) +#ifdef CONFIG_SPD_EEPROM + #define DEBUG +#endif + +#if defined(DEBUG) +void show_sdram_registers(void); +#endif + +/* + * This function is run very early, out of flash, and before devices are + * initialized. It is called by lib_ppc/board.c:board_init_f by virtue + * of being in the init_sequence array. + * + * The SDRAM has been initialized already -- start.S:start called + * init.S:init_sdram early on -- but it is not yet being used for + * anything, not even stack. So be careful. + */ + +#define CPC0_CR0 0xb1 /* Chip control register 0 */ +#define CPC0_CR1 0xb2 /* Chip control register 1 */ +/* Attention: If you want 1 microsecs times from the external oscillator + * use 0x00804051. But this causes problems with u-boot and linux! + */ +#define CPC0_CR1_VALUE 0x00004051 +#define CPC0_ECR 0xaa /* Edge condition register */ +#define EBC0_CFG 0x23 /* External Peripheral Control Register */ +#define CPC0_EIRR 0xb6 /* External Interrupt Register */ + + +int board_early_init_f (void) +{ + /*-------------------------------------------------------------------+ + | Interrupt controller setup for the HCU4 board. + | Note: IRQ 0-15 405GP internally generated; high; level sensitive + | IRQ 16 405GP internally generated; low; level sensitive + | IRQ 17-24 RESERVED/UNUSED + | IRQ 31 (EXT IRQ 6) (unused) + +-------------------------------------------------------------------*/ + mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */ + mtdcr (uicer, 0x00000000); /* disable all ints */ + mtdcr (uiccr, 0x00000000); /* set all to be non-critical */ + mtdcr (uicpr, 0xFFFFFF87); /* set int polarities */ + mtdcr (uictr, 0x10000000); /* set int trigger levels */ + mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */ + + mtdcr(CPC0_CR1, CPC0_CR1_VALUE); + mtdcr(CPC0_ECR, 0x60606000); + mtdcr(CPC0_EIRR, 0x7c000000); + + return 0; +} + +#ifdef CONFIG_BOARD_PRE_INIT +int board_pre_init (void) +{ + return board_early_init_f (); +} + +#endif + +enum { + /* HW_GENERATION_HCU wird nicht mehr unterstuetzt */ + HW_GENERATION_HCU2 = 0x10, + HW_GENERATION_HCU3 = 0x10, + HW_GENERATION_HCU4 = 0x20, + HW_GENERATION_MCU = 0x08, + HW_GENERATION_MCU20 = 0x0a, + HW_GENERATION_MCU25 = 0x09, +}; + +int checkboard (void) +{ +#define HCU_MACH_VERSIONS_REGISTER ( 0x7C000000 + 0xF00000 ) + unsigned j; + uint16_t *boardVersReg = (uint16_t *) HCU_MACH_VERSIONS_REGISTER; + uint16_t generation = *boardVersReg & 0xf0; + uint16_t index = *boardVersReg & 0x0f; + /* Force /RTS to active. The board it not wired quite + correctly to use cts/rtc flow control, so just force the + /RST active and forget about it. */ + writeb (readb (0xef600404) | 0x03, 0xef600404); + printf ("\nNetstal Maschinen AG "); + if (generation == HW_GENERATION_HCU3) + printf ("HCU3: index %d\n\n", index); + else if (generation == HW_GENERATION_HCU4) + printf ("HCU4: index %d\n\n", index); + /* GPIO here noch nicht richtig initialisert !!! */ + sysLedSet(0); + for (j=0; j < 7;j++) { + sysLedSet(1 << j); + udelay(50*1000); + } + return 0; +} + +u32 sysLedGet(void) +{ + return( ~( (*(u32 *)GPIO0_OR)) >> 23) & 0xff; +} + +void sysLedSet(u32 value /* value to place in LEDs */) +{ + u32 tmp = ~value; + u32 *ledReg; + tmp = (tmp << 23) | 0x7FFFFF; + ledReg = (u32 *)GPIO0_OR; + *ledReg = tmp; +} + +/* + * sdram_init - Dummy implementation for start.S, spd_sdram or initdram + * used for HCUx + */ +void sdram_init(void) +{ + return; +} + +#define mtsdram(reg, data) { mtdcr(memcfga,reg);mtdcr(memcfgd,data); } +#define mfsdram(value, reg) { mtdcr(memcfga,reg); value = mfdcr(memcfgd); } + +#if defined(DEBUG) +void show_sdram_registers(void) +{ + u32 value; + printf ("SDRAM Controller Registers --\n"); + mfsdram(value, mem_mcopt1); + printf (" SDRAM0_CFG : 0x%08x\n", value); + mfsdram(value, mem_status); + printf (" SDRAM0_STATUS: 0x%08x\n", value); + mfsdram(value, mem_mb0cf); + printf (" SDRAM0_B0CR : 0x%08x\n", value); + mfsdram(value, mem_mb1cf); + printf (" SDRAM0_B1CR : 0x%08x\n", value); + mfsdram(value, mem_sdtr1); + printf (" SDRAM0_TR : 0x%08x\n", value); + mfsdram(value, mem_rtr); + printf (" SDRAM0_RTR : 0x%08x\n", value); +} +#endif + +#define SDRAM_LEN 32*1024*1024 /* 32 MB -RAM */ + +/* + * this is even after checkboard. It returns the size of the SDRAM + * that we have installed. This function is called by board_init_f + * in lib_ppc/board.c to initialize the memory and return what I + * found. These are default value, which will be overridden later. + */ + +long int fixed_hcu4_sdram (int board_type) +{ +#ifdef DEBUG + printf (__FUNCTION__); +#endif + /* disable memory controller */ + mtdcr (memcfga, mem_mcopt1); + mtdcr (memcfgd, 0x00000000); + + udelay (500); + + /* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */ + mtdcr (memcfga, mem_besra); + mtdcr (memcfgd, 0xffffffff); + + /* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */ + mtdcr (memcfga, mem_besrb); + mtdcr (memcfgd, 0xffffffff); + + /* Clear SDRAM0_ECCCFG (disable ECC) */ + mtdcr (memcfga, mem_ecccf); + mtdcr (memcfgd, 0x00000000); + + /* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */ + mtdcr (memcfga, mem_eccerr); + mtdcr (memcfgd, 0xffffffff); + + /* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2 + * TODO ngngng + */ + mtdcr (memcfga, mem_sdtr1); + mtdcr (memcfgd, 0x008a4015); + + /* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1 + * TODO ngngng + */ + mtdcr (memcfga, mem_mb0cf); + mtdcr (memcfgd, 0x00062001); + + /* refresh timer = 0x400 */ + mtdcr (memcfga, mem_rtr); + mtdcr (memcfgd, 0x04000000); + + /* Power management idle timer set to the default. */ + mtdcr (memcfga, mem_pmit); + mtdcr (memcfgd, 0x07c00000); + + udelay (500); + + /* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) TODO */ + mtdcr (memcfga, mem_mcopt1); + mtdcr (memcfgd, 0x90800000); + +#ifdef DEBUG + printf ("%s: done\n", __FUNCTION__); +#endif + return SDRAM_LEN; +} + +/*---------------------------------------------------------------------------+ + * getSerialNr + *---------------------------------------------------------------------------*/ +static u32 getSerialNr(void) +{ + u32 *serial = (u32 *)CFG_FLASH_BASE; + if (*serial == 0xffffffff) { + return get_ticks(); + } + return *serial; +} + + +/*---------------------------------------------------------------------------+ + * misc_init_r. + *---------------------------------------------------------------------------*/ + +int misc_init_r(void) +{ + char *s = getenv("ethaddr"); + char *e; + int i; + u32 serial = getSerialNr(); + for (i = 0; i < 6; ++i) { + gd->bd->bi_enetaddr[i] = s ? simple_strtoul (s, &e, 16) : 0; + if (s) + s = (*e) ? e + 1 : e; + } + if (gd->bd->bi_enetaddr[3] == 0 && + gd->bd->bi_enetaddr[4] == 0 && + gd->bd->bi_enetaddr[5] == 0) { + char ethaddr[22]; + /* [0..3] Must be in sync with CONFIG_ETHADDR */ + gd->bd->bi_enetaddr[0] = 0x00; + gd->bd->bi_enetaddr[1] = 0x60; + gd->bd->bi_enetaddr[2] = 0x13; + gd->bd->bi_enetaddr[3] = (serial >> 16) & 0xff; + gd->bd->bi_enetaddr[4] = (serial >> 8) & 0xff; + gd->bd->bi_enetaddr[5] = (serial >> 0) & 0xff; + sprintf (ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X\0", + gd->bd->bi_enetaddr[0], gd->bd->bi_enetaddr[1], + gd->bd->bi_enetaddr[2], gd->bd->bi_enetaddr[3], + gd->bd->bi_enetaddr[4], gd->bd->bi_enetaddr[5]) ; + printf("%s: Setting eth %s serial 0x%x\n", __FUNCTION__, + ethaddr, serial); + setenv ("ethaddr", ethaddr); + } + return 0; +} + +#define DO_UGLY_SDRAM_WORKAROUND +#ifdef DO_UGLY_SDRAM_WORKAROUND + #include "i2c.h" +void set_spd_default_value(unsigned int spd_addr,uchar def_val) +{ + uchar value; + int res = i2c_read(SPD_EEPROM_ADDRESS, spd_addr, 1, &value, 1) ; + if (res == 0 && value == 0xff) { + res = i2c_write(SPD_EEPROM_ADDRESS, + spd_addr, 1, &def_val, 1) ; +#ifdef DEBUG + printf("%s: Setting spd offset %3d to %3d res %d\n", + __FUNCTION__, spd_addr, def_val, res); +#endif + } +} +#endif + +long int initdram(int board_type) +{ + long dram_size = 0; + +#if !defined(CONFIG_SPD_EEPROM) + dram_size = fixed_hcu4_sdram(); +#else +#ifdef DO_UGLY_SDRAM_WORKAROUND + /* Workaround if you have no working I2C-EEPROM-SPD-configuration */ + i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); + set_spd_default_value(2, 4); /* SDRAM Type */ + set_spd_default_value(7, 0); /* module width, high byte */ + set_spd_default_value(12, 1); /* Refresh or 0x81 */ + + /* Only correct for HCU3 with 32 MB RAM*/ + /* Number of bytes used by module manufacturer */ + set_spd_default_value( 0, 128); + set_spd_default_value( 1, 11 ); /* Total SPD memory size */ + set_spd_default_value( 2, 4 ); /* Memory type */ + set_spd_default_value( 3, 12 ); /* Number of row address bits */ + set_spd_default_value( 4, 9 ); /* Number of column address bits */ + set_spd_default_value( 5, 1 ); /* Number of module rows */ + set_spd_default_value( 6, 32 ); /* Module data width, LSB */ + set_spd_default_value( 7, 0 ); /* Module data width, MSB */ + set_spd_default_value( 8, 1 ); /* Module interface signal levels */ + /* SDRAM cycle time for highest CL (Tclk) */ + set_spd_default_value( 9, 112); + /* SDRAM access time from clock for highest CL (Tac) */ + set_spd_default_value(10, 84 ); + set_spd_default_value(11, 2 ); /* Module configuration type */ + set_spd_default_value(12, 128); /* Refresh rate/type */ + set_spd_default_value(13, 16 ); /* Primary SDRAM width */ + set_spd_default_value(14, 8 ); /* Error Checking SDRAM width */ + /* SDRAM device attributes, min clock delay for back to back */ + /*random column addresses (Tccd) */ + set_spd_default_value(15, 1 ); + /* SDRAM device attributes, burst lengths supported */ + set_spd_default_value(16, 143); + /* SDRAM device attributes, number of banks on SDRAM device */ + set_spd_default_value(17, 4 ); + /* SDRAM device attributes, CAS latency */ + set_spd_default_value(18, 6 ); + /* SDRAM device attributes, CS latency */ + set_spd_default_value(19, 1 ); + /* SDRAM device attributes, WE latency */ + set_spd_default_value(20, 1 ); + set_spd_default_value(21, 0 ); /* SDRAM module attributes */ + /* SDRAM device attributes, general */ + set_spd_default_value(22, 14 ); + /* SDRAM cycle time for 2nd highest CL (Tclk) */ + set_spd_default_value(23, 117); + /* SDRAM access time from clock for2nd highest CL (Tac) */ + set_spd_default_value(24, 84 ); + /* SDRAM cycle time for 3rd highest CL (Tclk) */ + set_spd_default_value(25, 0 ); + /* SDRAM access time from clock for3rd highest CL (Tac) */ + set_spd_default_value(26, 0 ); + set_spd_default_value(27, 15 ); /* Minimum row precharge time (Trp) */ + /* Minimum row active to row active delay (Trrd) */ + set_spd_default_value(28, 14 ); + set_spd_default_value(29, 15 ); /* Minimum CAS to RAS delay (Trcd) */ + set_spd_default_value(30, 37 ); /* Minimum RAS pulse width (Tras) */ + set_spd_default_value(31, 8 ); /* Module bank density */ + /* Command and Address signal input setup time */ + set_spd_default_value(32, 21 ); + /* Command and Address signal input hold time */ + set_spd_default_value(33, 8 ); + set_spd_default_value(34, 21 ); /* Data signal input setup time */ + set_spd_default_value(35, 8 ); /* Data signal input hold time */ +#endif /* DO_UGLY_SDRAM_WORKAROUND */ + dram_size = spd_sdram(0); +#endif + +#ifdef DEBUG + show_sdram_registers(); +#endif + +#if defined(CFG_DRAM_TEST) + bcu4_testdram(dram_size); + printf("%s %d MB of SDRAM\n", __FUNCTION__, dram_size/(1024*1024)); +#endif + return dram_size; +} + + -- cgit v1.1 From 157cda4d0c3d592ccbb19bbfc07d9251894f0894 Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Fri, 27 Jul 2007 11:31:22 +0200 Subject: Add PPC4xx-HCU4 and HCU5 boards: HCU5 files Signed-off-by: Niklaus Giger --- board/netstal/hcu5/hcu5.c | 526 +++++++++++++++++++++++++++++++++++++++++++++ board/netstal/hcu5/init.S | 81 +++++++ board/netstal/hcu5/sdram.c | 299 ++++++++++++++++++++++++++ 3 files changed, 906 insertions(+) create mode 100644 board/netstal/hcu5/hcu5.c create mode 100644 board/netstal/hcu5/init.S create mode 100644 board/netstal/hcu5/sdram.c (limited to 'board/netstal') diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c new file mode 100644 index 0000000..59107b9 --- /dev/null +++ b/board/netstal/hcu5/hcu5.c @@ -0,0 +1,526 @@ +/* + *(C) Copyright 2005-2007 Netstal Maschinen AG + * Niklaus Giger (Niklaus.Giger@netstal.com) + * + * This source code is free software; you can redistribute it + * and/or modify it in source code form under the terms of the GNU + * General Public License as published by the Free Software + * Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA + */ + +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +void sysLedSet(u32 value); + +extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; + +#define mtcpr0(reg, data) do { mtdcr(CPR0_CFGADDR,reg); \ + mtdcr(CPR0_CFGDATA,data); } while (0) +#define mfcpr0(reg, data) do { mtdcr(CPR0_CFGADDR,reg); \ + data = mfdcr(CPR0_CFGDATA); } while (0) + +#define SDR0_CP440 0x0180 + +/* + * This function is run very early, out of flash, and before devices are + * initialized. It is called by lib_ppc/board.c:board_init_f by virtue + * of being in the init_sequence array. + * + * The SDRAM has been initialized already -- start.S:start called + * init.S:init_sdram early on -- but it is not yet being used for + * anything, not even stack. So be careful. + */ + +int board_early_init_f(void) +{ + u32 reg; + +#undef BOOTSTRAP_OPTION_A_ACTIVE +#ifdef BOOTSTRAP_OPTION_A_ACTIVE + /* Booting with Bootstrap Option A + * First boot, with CPR0_ICFG_RLI_MASK == 0 + * no we setup varios boot strapping register, + * then we do reset the PPC440 using a chip reset + * Unfortunately, we cannot use this option, as Nto1 is not set + * with Bootstrap Option A and cannot be changed later on by SW + * There are no other possible boostrap options with a 8 bit ROM + * See Errata (Version 1.04) CHIP_9 + */ + + u32 cpr0icfg; + u32 dbcr; + mfcpr0(CPR0_ICFG, cpr0icfg); + if ( ! (cpr0icfg & CPR0_ICFG_RLI_MASK ) ) { + mtcpr0(CPR0_MALD, 0x02000000); + mtcpr0(CPR0_OPBD, 0x02000000); + mtcpr0(CPR0_PERD, 0x05000000); /* 1:5 */ + mtcpr0(CPR0_PLLC, 0x40000238); + mtcpr0(CPR0_PLLD, 0x01010414); + mtcpr0(CPR0_PRIMAD, 0x01000000); + mtcpr0(CPR0_PRIMBD, 0x01000000); + mtcpr0(CPR0_SPCID, 0x03000000); + mtsdr(SDR0_PFC0, 0x00003E00); /* [CTE] = 0 */ + mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/ + mtcpr0(CPR0_ICFG, cpr0icfg | CPR0_ICFG_RLI_MASK); + + /* + * Initiate system reset in debug control register DBCR + */ + dbcr = mfspr(dbcr0); + #define SYSTEM_RESET 0x30000000 + #define CHIP_RESET 0x20000000 + mtspr(dbcr0, dbcr | CHIP_RESET ); + } + mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/ +#endif + mtdcr(ebccfga, xbcfg); + mtdcr(ebccfgd, 0xb8400000); + + /*-------------------------------------------------------------------- + * Setup the GPIO pins + *-------------------------------------------------------------------*/ + /* test-only: take GPIO init from pcs440ep ???? in config file */ + out32(GPIO0_OR, 0x00000000); + out32(GPIO0_TCR, 0x7C2FF1CF); + out32(GPIO0_OSRL, 0x40055000); + out32(GPIO0_OSRH, 0x00000000); + out32(GPIO0_TSRL, 0x40055000); + out32(GPIO0_TSRH, 0x00000400); + out32(GPIO0_ISR1L, 0x40000000); + out32(GPIO0_ISR1H, 0x00000000); + out32(GPIO0_ISR2L, 0x00000000); + out32(GPIO0_ISR2H, 0x00000000); + out32(GPIO0_ISR3L, 0x00000000); + out32(GPIO0_ISR3H, 0x00000000); + + out32(GPIO1_OR, 0x00000000); + out32(GPIO1_TCR, 0xC6007FFF); + out32(GPIO1_OSRL, 0x00140000); + out32(GPIO1_OSRH, 0x00000000); + out32(GPIO1_TSRL, 0x00000000); + out32(GPIO1_TSRH, 0x00000000); + out32(GPIO1_ISR1L, 0x05415555); + out32(GPIO1_ISR1H, 0x40000000); + out32(GPIO1_ISR2L, 0x00000000); + out32(GPIO1_ISR2H, 0x00000000); + out32(GPIO1_ISR3L, 0x00000000); + out32(GPIO1_ISR3H, 0x00000000); + + /*-------------------------------------------------------------------- + * Setup the interrupt controller polarities, triggers, etc. + *-------------------------------------------------------------------*/ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + mtdcr(uic0er, 0x00000000); /* disable all */ + mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */ + mtdcr(uic0pr, 0xfffff7ff); /* per ref-board manual */ + mtdcr(uic0tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + + mtdcr(uic1sr, 0xffffffff); /* clear all */ + mtdcr(uic1er, 0x00000000); /* disable all */ + mtdcr(uic1cr, 0x00000000); /* all non-critical */ + mtdcr(uic1pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic1tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic1sr, 0xffffffff); /* clear all */ + + mtdcr(uic2sr, 0xffffffff); /* clear all */ + mtdcr(uic2er, 0x00000000); /* disable all */ + mtdcr(uic2cr, 0x00000000); /* all non-critical */ + mtdcr(uic2pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic2tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic2sr, 0xffffffff); /* clear all */ + mtsdr(sdr_pfc0, 0x00003E00); /* Pin function: */ + mtsdr(sdr_pfc1, 0x00848000); /* Pin function: UART0 has 4 pins */ + + /* PCI arbiter enabled */ + mfsdr(sdr_pci0, reg); + mtsdr(sdr_pci0, 0x80000000 | reg); + + pci_pre_init(0); + + /* setup BOOT FLASH */ + mtsdr(SDR0_CUST0, 0xC0082350); + + return 0; +} + +#ifdef CONFIG_BOARD_PRE_INIT +int board_pre_init (void) +{ + return board_early_init_f (); +} + +#endif + +enum { + /* HW_GENERATION_HCU1 is no longer supported */ + HW_GENERATION_HCU2 = 0x10, + HW_GENERATION_HCU3 = 0x10, + HW_GENERATION_HCU4 = 0x20, + HW_GENERATION_HCU5 = 0x30, + HW_GENERATION_MCU = 0x08, + HW_GENERATION_MCU20 = 0x0a, + HW_GENERATION_MCU25 = 0x09, +}; + +int checkboard (void) +{ +#define SDR0_ECID0 0x0080 +#define SDR0_ECID1 0x0081 +#define SDR0_ECID2 0x0082 +#define SDR0_ECID3 0x0083 + unsigned j; + uint16_t *hwVersReg = (uint16_t *) HCU_HW_VERSION_REGISTER; + uint16_t *boardVersReg = (uint16_t *) HCU_CPLD_VERSION_REGISTER; + uint16_t generation = *boardVersReg & 0xf0; + uint16_t index = *boardVersReg & 0x0f; + ulong ecid0, ecid1, ecid2, ecid3; + printf ("Netstal Maschinen AG: "); + if (generation == HW_GENERATION_HCU3) + printf ("HCU3: index %d", index); + else if (generation == HW_GENERATION_HCU4) + printf ("HCU4: index %d", index); + else if (generation == HW_GENERATION_HCU5) + printf ("HCU5: index %d", index); + printf (" HW 0x%02x\n", *hwVersReg & 0xff); + mfsdr(SDR0_ECID0, ecid0); + mfsdr(SDR0_ECID1, ecid1); + mfsdr(SDR0_ECID2, ecid2); + mfsdr(SDR0_ECID3, ecid3); + + printf("Chip ID 0x%x 0x%x 0x%x 0x%x\n", ecid0, ecid1, ecid2, ecid3); + for (j=0; j < 6;j++) { + sysLedSet(1 << j); + udelay(200*1000); + } + return 0; +} + +#define SYS_IO_ADDRESS 0xcce00000 + +u32 sysLedGet(void) +{ + return in16(SYS_IO_ADDRESS) & 0x3f; +} + +void sysLedSet(u32 value /* value to place in LEDs */) +{ + out16(SYS_IO_ADDRESS, value); +} + +/*---------------------------------------------------------------------------+ + * getSerialNr + *---------------------------------------------------------------------------*/ +static u32 getSerialNr(void) +{ + u32 *serial = (u32 *)CFG_FLASH_BASE; + if (*serial == 0xffffffff) { + return get_ticks(); + } + return *serial; +} + + +/*---------------------------------------------------------------------------+ + * misc_init_r. + *---------------------------------------------------------------------------*/ + +#define DEFAULT_ETH_ADDR "ethaddr" +/* ethaddr for first or etha1ddr for second ethernet */ + +int misc_init_r(void) +{ + char *s = getenv(DEFAULT_ETH_ADDR); + char *e; + int i; + u32 serial = getSerialNr(); + unsigned long usb2d0cr = 0; + unsigned long usb2phy0cr, usb2h0cr = 0; + unsigned long sdr0_pfc1; + + for (i = 0; i < 6; ++i) { + gd->bd->bi_enetaddr[i] = s ? simple_strtoul (s, &e, 16) : 0; + if (s) + s = (*e) ? e + 1 : e; + } + if (gd->bd->bi_enetaddr[3] == 0 && + gd->bd->bi_enetaddr[4] == 0 && + gd->bd->bi_enetaddr[5] == 0) { + char ethaddr[22]; + /* Must be in sync with CONFIG_ETHADDR */ + gd->bd->bi_enetaddr[0] = 0x00; + gd->bd->bi_enetaddr[1] = 0x60; + gd->bd->bi_enetaddr[2] = 0x13; + gd->bd->bi_enetaddr[3] = (serial >> 16) & 0xff; + gd->bd->bi_enetaddr[4] = (serial >> 8) & 0xff; + /* byte[5].bit 0 must be zero */ + gd->bd->bi_enetaddr[5] = (serial >> 0) & 0xfe; + sprintf (ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X\0", + gd->bd->bi_enetaddr[0], gd->bd->bi_enetaddr[1], + gd->bd->bi_enetaddr[2], gd->bd->bi_enetaddr[3], + gd->bd->bi_enetaddr[4], gd->bd->bi_enetaddr[5]) ; + printf("%s: Setting eth %s serial 0x%x\n", __FUNCTION__, + ethaddr, serial); + setenv (DEFAULT_ETH_ADDR, ethaddr); + } +#ifdef CFG_ENV_IS_IN_FLASH + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + -CFG_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); + + /* Env protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + CFG_ENV_ADDR_REDUND, + CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1, + &flash_info[0]); +#endif + + /* + * USB stuff... + */ + + /* SDR Setting */ + mfsdr(SDR0_PFC1, sdr0_pfc1); + mfsdr(SDR0_USB2D0CR, usb2d0cr); + mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mfsdr(SDR0_USB2H0CR, usb2h0cr); + + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/ + + /* An 8-bit/60MHz interface is the only possible alternative + when connecting the Device to the PHY */ + usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; + usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/ + + /* To enable the USB 2.0 Device function through the UTMI interface */ + usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK; + usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION; /*1*/ + + sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK; + sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL; /*0*/ + + mtsdr(SDR0_PFC1, sdr0_pfc1); + mtsdr(SDR0_USB2D0CR, usb2d0cr); + mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mtsdr(SDR0_USB2H0CR, usb2h0cr); + + /*clear resets*/ + udelay (1000); + mtsdr(SDR0_SRST1, 0x00000000); + udelay (1000); + mtsdr(SDR0_SRST0, 0x00000000); + + printf("USB: Host(int phy) Device(ext phy)\n"); + + return 0; +} + +/************************************************************************* + * pci_pre_init + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) +int pci_pre_init(struct pci_controller *hose) +{ + unsigned long addr; + + /*-------------------------------------------------------------------+ + * As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM. + * Workaround: Disable write pipelining to DDR SDRAM by setting + * PLB0_ACR[WRP] = 0. + *-------------------------------------------------------------------*/ + + /*-------------------------------------------------------------------+ + | Set priority for all PLB3 devices to 0. + | Set PLB3 arbiter to fair mode. + +-------------------------------------------------------------------*/ + mfsdr(sdr_amp1, addr); + mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb3_acr); + // mtdcr(plb3_acr, addr & ~plb1_acr_wrp_mask); /* ngngng */ + mtdcr(plb3_acr, addr | 0x80000000); /* Sequoia */ + + /*-------------------------------------------------------------------+ + | Set priority for all PLB4 devices to 0. + +-------------------------------------------------------------------*/ + mfsdr(sdr_amp0, addr); + mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */ +// mtdcr(plb4_acr, addr & ~plb1_acr_wrp_mask); /* ngngng */ + mtdcr(plb4_acr, addr); /* Sequoia */ + + /*-------------------------------------------------------------------+ + | Set Nebula PLB4 arbiter to fair mode. + +-------------------------------------------------------------------*/ + /* Segment0 */ + addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair; + addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled; + addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep; +// addr = (addr & ~plb0_acr_wrp_mask) ; /* ngngng */ + addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; /* Sequoia */ + + // mtdcr(plb0_acr, addr); /* Sequoia */ + mtdcr(plb0_acr, 0); // PATCH HAB: WRITE PIPELINING OFF + + + /* Segment1 */ + addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair; + addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled; + addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep; + addr = (addr & ~plb1_acr_wrp_mask) ; + // mtdcr(plb1_acr, addr); /* Sequoia */ + mtdcr(plb1_acr, 0); // PATCH HAB: WRITE PIPELINING OFF + + return 1; +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */ + +/************************************************************************* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller *hose) +{ + /*-------------------------------------------------------------+ + * Set up Direct MMIO registers + *-------------------------------------------------------------*/ + /*-------------------------------------------------------------+ + | PowerPC440EPX PCI Master configuration. + | Map one 1Gig range of PLB/processor addresses to PCI memory space. + | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address + | 0xA0000000-0xDFFFFFFF + | Use byte reversed out routines to handle endianess. + | Make this region non-prefetchable. + +-------------------------------------------------------------*/ + /* PMM0 Mask/Attribute - disabled b4 setting */ + out32r(PCIX0_PMM0MA, 0x00000000); + out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */ + /* PMM0 PCI Low Address */ + out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); + out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ + /* 512M + No prefetching, and enable region */ + out32r(PCIX0_PMM0MA, 0xE0000001); + + /* PMM0 Mask/Attribute - disabled b4 setting */ + out32r(PCIX0_PMM1MA, 0x00000000); + out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */ + /* PMM0 PCI Low Address */ + out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); + out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */ + /* 512M + No prefetching, and enable region */ + out32r(PCIX0_PMM1MA, 0xE0000001); + + out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */ + out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */ + out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */ + out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */ + + /*------------------------------------------------------------------+ + * Set up Configuration registers + *------------------------------------------------------------------*/ + + /* Program the board's subsystem id/vendor id */ + pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, + CFG_PCI_SUBSYS_VENDORID); + pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID); + + /* Configure command register as bus master */ + pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); + + /* 240nS PCI clock */ + pci_write_config_word(0, PCI_LATENCY_TIMER, 1); + + /* No error reporting */ + pci_write_config_word(0, PCI_ERREN, 0); + + pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); + +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ + +/************************************************************************* + * pci_master_init + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) +void pci_master_init(struct pci_controller *hose) +{ + unsigned short temp_short; + + /*---------------------------------------------------------------+ + | Write the PowerPC440 EP PCI Configuration regs. + | Enable PowerPC440 EP to be a master on the PCI bus (PMM). + | Enable PowerPC440 EP to act as a PCI memory target (PTM). + +--------------------------------------------------------------*/ + pci_read_config_word(0, PCI_COMMAND, &temp_short); + pci_write_config_word(0, PCI_COMMAND, + temp_short | PCI_COMMAND_MASTER | + PCI_COMMAND_MEMORY); +} +#endif +/* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */ + +/************************************************************************* + * is_pci_host + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + * + * + ************************************************************************/ +#if defined(CONFIG_PCI) +int is_pci_host(struct pci_controller *hose) +{ + return 1; +} +#endif /* defined(CONFIG_PCI) */ + diff --git a/board/netstal/hcu5/init.S b/board/netstal/hcu5/init.S new file mode 100644 index 0000000..6da5f22 --- /dev/null +++ b/board/netstal/hcu5/init.S @@ -0,0 +1,81 @@ +/* + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/************************************************************************** + * TLB TABLE + * + * This table is used by the cpu boot code to setup the initial tlb + * entries. Rather than make broad assumptions in the cpu source tree, + * this table lets each board set things up however they like. + * + * Pointer to the table is returned in r1 + * + *************************************************************************/ + .section .bootpg,"ax" + .globl tlbtab + +tlbtab: + tlbtab_start + + /* vxWorks needs this entry for the Machine Check interrupt, */ + /* tlbentry( 0x40000000, SZ_256M, 0, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) */ + + /* + * BOOT_CS (FLASH) must be second. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry( CFG_BOOT_BASE_ADDR, SZ_1M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G ) + + /* TLB-entry for PCI Memory */ + tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I ) + + /* TLB-entry for EBC (CFG_CPLD) */ + // tlbentry( CFG_CPLD, SZ_1K, CFG_CPLD, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + /* CAN */ + tlbentry( CFG_CS_1, SZ_16M, CFG_CS_1, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + /* IMC + CPLD */ + tlbentry( CFG_CS_2, SZ_16M, CFG_CS_2, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + tlbentry( CFG_CS_2 + 0x1000000, SZ_16M, CFG_CS_2 + 0x1000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + /* IMC-Fast */ + tlbentry( CFG_CS_3, SZ_16M, CFG_CS_3, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + tlbentry( CFG_CS_3 + 0x1000000, SZ_16M, CFG_CS_3 + 0x1000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + + /* TLB-entry for Internal Registers & OCM */ + tlbentry( CFG_PCI_BASE, SZ_16M, 0xe0000000, 0, AC_R|AC_W|AC_X|SA_I ) + + /*TLB-entry PCI registers*/ + tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + + /* TLB-entry for peripherals */ + tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I) + + /* TLB for SDRAM will be added by initdram (sdram.c) */ + + tlbtab_end + + diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c new file mode 100644 index 0000000..f7d6865 --- /dev/null +++ b/board/netstal/hcu5/sdram.c @@ -0,0 +1,299 @@ +/* + * (C) Copyright 2007 + * Niklaus Giger (Niklaus.Giger@netstal.com) + * (C) Copyright 2006 + * Sylvie Gohl, AMCC/IBM, gohl.sylvie@fr.ibm.com + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Thierry Roman, AMCC/IBM, thierry_roman@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * Robert Snyder, AMCC/IBM, rob.snyder@fr.ibm.com + * + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* define DEBUG for debug output */ +#undef DEBUG + +#include +#include +#include +#include +#include + +void sysLedSet(u32 value); +void dcbz_area(u32 start_address, u32 num_bytes); +void dflush(void); + +#define DDR_DCR_BASE 0x10 +#define ddrcfga (DDR_DCR_BASE+0x0) /* DDR configuration address reg */ +#define ddrcfgd (DDR_DCR_BASE+0x1) /* DDR configuration data reg */ + +#define DDR0_01_INT_MASK_MASK 0x000000FF +#define DDR0_00_INT_ACK_ALL 0x7F000000 +#define DDR0_01_INT_MASK_ALL_ON 0x000000FF +#define DDR0_01_INT_MASK_ALL_OFF 0x00000000 + +#define DDR0_17_DLLLOCKREG_MASK 0x00010000 /* Read only */ +#define DDR0_17_DLLLOCKREG_UNLOCKED 0x00000000 +#define DDR0_17_DLLLOCKREG_LOCKED 0x00010000 + +#define DDR0_22 0x16 +/* ECC */ +#define DDR0_22_CTRL_RAW_MASK 0x03000000 +#define DDR0_22_CTRL_RAW_ECC_DISABLE 0x00000000 /* ECC not enabled */ +#define DDR0_22_CTRL_RAW_ECC_CHECK_ONLY 0x01000000 /* ECC no correction */ +#define DDR0_22_CTRL_RAW_NO_ECC_RAM 0x02000000 /* Not a ECC RAM*/ +#define DDR0_22_CTRL_RAW_ECC_ENABLE 0x03000000 /* ECC correcting on */ +#define DDR0_03_CASLAT_DECODE(n) ((((unsigned long)(n))>>16)&0x7) + +#ifdef CFG_ENABLE_SDRAM_CACHE +#define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on DDR2 */ +#else +#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on DDR2 */ +#endif + +void program_tlb(u32 phys_addr, u32 virt_addr, u32 size, u32 tlb_word2_i_value); + +#ifdef CONFIG_ADD_RAM_INFO +void board_add_ram_info(int use_default) +{ + PPC440_SYS_INFO board_cfg; + u32 val; + mfsdram(DDR0_22, val); + val &= DDR0_22_CTRL_RAW_MASK; + switch (val) { + case DDR0_22_CTRL_RAW_ECC_DISABLE: + puts(" (ECC disabled"); + break; + case DDR0_22_CTRL_RAW_ECC_CHECK_ONLY: + puts(" (ECC check only"); + break; + case DDR0_22_CTRL_RAW_NO_ECC_RAM: + puts(" (no ECC ram"); + break; + case DDR0_22_CTRL_RAW_ECC_ENABLE: + puts(" (ECC enabled"); + break; + } + + get_sys_info(&board_cfg); + printf(", %d MHz", (board_cfg.freqPLB * 2) / 1000000); + + mfsdram(DDR0_03, val); + val = DDR0_03_CASLAT_DECODE(val); + printf(", CL%d)", val); +} +#endif + +/*-------------------------------------------------------------------- + * wait_for_dlllock. + *--------------------------------------------------------------------*/ +static int wait_for_dlllock(void) +{ + unsigned long val; + int wait = 0; + + /* -----------------------------------------------------------+ + * Wait for the DCC master delay line to finish calibration + * ----------------------------------------------------------*/ + mtdcr(ddrcfga, DDR0_17); + val = DDR0_17_DLLLOCKREG_UNLOCKED; + + while (wait != 0xffff) { + val = mfdcr(ddrcfgd); + if ((val & DDR0_17_DLLLOCKREG_MASK) == + DDR0_17_DLLLOCKREG_LOCKED) + /* dlllockreg bit on */ + return 0; + else + wait++; + } + debug("0x%04x: DDR0_17 Value (dlllockreg bit): 0x%08x\n", wait, val); + debug("Waiting for dlllockreg bit to raise\n"); + + return -1; +} + +/*********************************************************************** + * + * sdram_panic -- Panic if we cannot configure the sdram correctly + * + ************************************************************************/ +void sdram_panic(const char *reason) +{ + printf("\n%s: reason %s", __FUNCTION__, reason); + sysLedSet(0xff); + while (1) { + } + /* Never return */ +} + +#ifdef CONFIG_DDR_ECC +static void blank_string(int size) +{ + int i; + + for (i=0; i> ! */ + mtsdram(DDR0_00, 0x0000190A); + mtsdram(DDR0_01, 0x01000000); + mtsdram(DDR0_03, 0x02030602); + mtsdram(DDR0_04, 0x0A020200); + mtsdram(DDR0_05, 0x02020307); + switch (*hwVersReg & HCU_HW_SDRAM_CONFIG_MASK) { + case 0: + dram_size = 128 * 1024 * 1024 ; + mtsdram(DDR0_06, 0x0102C80D); // 128MB RAM + mtsdram(DDR0_11, 0x000FC800); // 128MB RAM + mtsdram(DDR0_43, 0x030A0300); // 128MB RAM + break; + case 1: + dram_size = 256 * 1024 * 1024 ; + mtsdram(DDR0_06, 0x0102C812); // 256MB RAM + mtsdram(DDR0_11, 0x0014C800); // 256MB RAM + mtsdram(DDR0_43, 0x030A0200); // 256MB RAM + break; + default: + sdram_panic(INVALID_HW_CONFIG); + break; + } + dram_size -= 16 * 1024 * 1024; + mtsdram(DDR0_07, 0x00090100); + // TCPD=200 cycles of clock input is required to lock the DLL. + // CKE must be HIGH the entire time.mtsdram(DDR0_08, 0x02C80001); + mtsdram(DDR0_08, 0x02C80001); + mtsdram(DDR0_09, 0x00011D5F); + mtsdram(DDR0_10, 0x00000100); + mtsdram(DDR0_12, 0x00000003); + mtsdram(DDR0_14, 0x00000000); + mtsdram(DDR0_17, 0x1D000000); + mtsdram(DDR0_18, 0x1D1D1D1D); + mtsdram(DDR0_19, 0x1D1D1D1D); + mtsdram(DDR0_20, 0x0B0B0B0B); + mtsdram(DDR0_21, 0x0B0B0B0B); + #define ECC_RAM 0x03267F0B + #define NO_ECC_RAM 0x00267F0B +#ifdef CONFIG_DDR_ECC + mtsdram(DDR0_22, ECC_RAM); +#else + mtsdram(DDR0_22, NO_ECC_RAM); +#endif + + mtsdram(DDR0_23, 0x00000000); + mtsdram(DDR0_24, 0x01020001); + mtsdram(DDR0_26, 0x2D930517); + mtsdram(DDR0_27, 0x00008236); + mtsdram(DDR0_28, 0x00000000); + mtsdram(DDR0_31, 0x00000000); + mtsdram(DDR0_42, 0x01000006); + mtsdram(DDR0_44, 0x00000003); + mtsdram(DDR0_02, 0x00000001); + wait_for_dlllock(); + mtsdram(DDR0_00, 0x40000000); /* Zero init bit */ + + /* + * Program tlb entries for this size (dynamic) + */ + program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE); + + /* + * Setup 2nd TLB with same physical address but different virtual + * address with cache enabled. This is done for fast ECC generation. + */ + program_tlb(0, CFG_DDR_CACHED_ADDR, dram_size, 0); + +#ifdef CONFIG_DDR_ECC + /* + * If ECC is enabled, initialize the parity bits. + */ + program_ecc(CFG_DDR_CACHED_ADDR, dram_size, 0); +#endif + + return (dram_size); +} -- cgit v1.1 From 35d22f957a85a22bb3cd1ad084fa5404620d1c42 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 10 Aug 2007 10:42:25 +0200 Subject: Coding style cleanup Signed-off-by: Stefan Roese --- board/netstal/common/nm_bsp.c | 1 - board/netstal/hcu4/config.mk | 1 - board/netstal/hcu4/hcu4.c | 80 ++++++++++--------- board/netstal/hcu5/config.mk | 1 - board/netstal/hcu5/hcu5.c | 177 +++++++++++++++++++++--------------------- board/netstal/hcu5/init.S | 4 +- board/netstal/hcu5/sdram.c | 23 +++--- 7 files changed, 147 insertions(+), 140 deletions(-) (limited to 'board/netstal') diff --git a/board/netstal/common/nm_bsp.c b/board/netstal/common/nm_bsp.c index ee1b684..1e06780 100644 --- a/board/netstal/common/nm_bsp.c +++ b/board/netstal/common/nm_bsp.c @@ -39,4 +39,3 @@ U_BOOT_CMD( "Help for Netstal Maschinen BSP specific command.\n" ); #endif - diff --git a/board/netstal/hcu4/config.mk b/board/netstal/hcu4/config.mk index f5a4ce4..376609a 100644 --- a/board/netstal/hcu4/config.mk +++ b/board/netstal/hcu4/config.mk @@ -26,4 +26,3 @@ TEXT_BASE = 0xFFFa0000 ifeq ($(debug),1) PLATFORM_CPPFLAGS += -DDEBUG -g endif - diff --git a/board/netstal/hcu4/hcu4.c b/board/netstal/hcu4/hcu4.c index deb7d2d..252aaa7 100644 --- a/board/netstal/hcu4/hcu4.c +++ b/board/netstal/hcu4/hcu4.c @@ -27,10 +27,30 @@ DECLARE_GLOBAL_DATA_PTR; +#define HCU_MACH_VERSIONS_REGISTER (0x7C000000 + 0xF00000) + +#define mtsdram(reg, data) { mtdcr(memcfga,reg);mtdcr(memcfgd,data); } +#define mfsdram(value, reg) { mtdcr(memcfga,reg); value = mfdcr(memcfgd); } + +#define SDRAM_LEN 32*1024*1024 /* 32 MB -RAM */ + +#define DO_UGLY_SDRAM_WORKAROUND + +enum { + /* HW_GENERATION_HCU wird nicht mehr unterstuetzt */ + HW_GENERATION_HCU2 = 0x10, + HW_GENERATION_HCU3 = 0x10, + HW_GENERATION_HCU4 = 0x20, + HW_GENERATION_MCU = 0x08, + HW_GENERATION_MCU20 = 0x0a, + HW_GENERATION_MCU25 = 0x09, +}; + void sysLedSet(u32 value); -long int spd_sdram(int(read_spd)(uint addr)) +long int spd_sdram(int(read_spd)(uint addr)); + #ifdef CONFIG_SPD_EEPROM - #define DEBUG +#define DEBUG #endif #if defined(DEBUG) @@ -86,26 +106,15 @@ int board_pre_init (void) { return board_early_init_f (); } - #endif -enum { - /* HW_GENERATION_HCU wird nicht mehr unterstuetzt */ - HW_GENERATION_HCU2 = 0x10, - HW_GENERATION_HCU3 = 0x10, - HW_GENERATION_HCU4 = 0x20, - HW_GENERATION_MCU = 0x08, - HW_GENERATION_MCU20 = 0x0a, - HW_GENERATION_MCU25 = 0x09, -}; - int checkboard (void) { -#define HCU_MACH_VERSIONS_REGISTER ( 0x7C000000 + 0xF00000 ) - unsigned j; - uint16_t *boardVersReg = (uint16_t *) HCU_MACH_VERSIONS_REGISTER; - uint16_t generation = *boardVersReg & 0xf0; - uint16_t index = *boardVersReg & 0x0f; + unsigned int j; + u16 *boardVersReg = (u16 *) HCU_MACH_VERSIONS_REGISTER; + u16 generation = *boardVersReg & 0xf0; + u16 index = *boardVersReg & 0x0f; + /* Force /RTS to active. The board it not wired quite correctly to use cts/rtc flow control, so just force the /RST active and forget about it. */ @@ -117,24 +126,26 @@ int checkboard (void) printf ("HCU4: index %d\n\n", index); /* GPIO here noch nicht richtig initialisert !!! */ sysLedSet(0); - for (j=0; j < 7;j++) { + for (j = 0; j < 7; j++) { sysLedSet(1 << j); - udelay(50*1000); + udelay(50 * 1000); } + return 0; } u32 sysLedGet(void) { - return( ~( (*(u32 *)GPIO0_OR)) >> 23) & 0xff; + return (~((*(u32 *)GPIO0_OR)) >> 23) & 0xff; } void sysLedSet(u32 value /* value to place in LEDs */) { u32 tmp = ~value; u32 *ledReg; - tmp = (tmp << 23) | 0x7FFFFF; - ledReg = (u32 *)GPIO0_OR; + + tmp = (tmp << 23) | 0x7FFFFF; + ledReg = (u32 *)GPIO0_OR; *ledReg = tmp; } @@ -147,13 +158,11 @@ void sdram_init(void) return; } -#define mtsdram(reg, data) { mtdcr(memcfga,reg);mtdcr(memcfgd,data); } -#define mfsdram(value, reg) { mtdcr(memcfga,reg); value = mfdcr(memcfgd); } - #if defined(DEBUG) void show_sdram_registers(void) { u32 value; + printf ("SDRAM Controller Registers --\n"); mfsdram(value, mem_mcopt1); printf (" SDRAM0_CFG : 0x%08x\n", value); @@ -170,8 +179,6 @@ void show_sdram_registers(void) } #endif -#define SDRAM_LEN 32*1024*1024 /* 32 MB -RAM */ - /* * this is even after checkboard. It returns the size of the SDRAM * that we have installed. This function is called by board_init_f @@ -244,9 +251,10 @@ long int fixed_hcu4_sdram (int board_type) static u32 getSerialNr(void) { u32 *serial = (u32 *)CFG_FLASH_BASE; - if (*serial == 0xffffffff) { + + if (*serial == 0xffffffff) return get_ticks(); - } + return *serial; } @@ -260,12 +268,14 @@ int misc_init_r(void) char *s = getenv("ethaddr"); char *e; int i; - u32 serial = getSerialNr(); + u32 serial = getSerialNr(); + for (i = 0; i < 6; ++i) { gd->bd->bi_enetaddr[i] = s ? simple_strtoul (s, &e, 16) : 0; if (s) s = (*e) ? e + 1 : e; } + if (gd->bd->bi_enetaddr[3] == 0 && gd->bd->bi_enetaddr[4] == 0 && gd->bd->bi_enetaddr[5] == 0) { @@ -288,13 +298,14 @@ int misc_init_r(void) return 0; } -#define DO_UGLY_SDRAM_WORKAROUND #ifdef DO_UGLY_SDRAM_WORKAROUND - #include "i2c.h" +#include "i2c.h" + void set_spd_default_value(unsigned int spd_addr,uchar def_val) { uchar value; int res = i2c_read(SPD_EEPROM_ADDRESS, spd_addr, 1, &value, 1) ; + if (res == 0 && value == 0xff) { res = i2c_write(SPD_EEPROM_ADDRESS, spd_addr, 1, &def_val, 1) ; @@ -387,7 +398,6 @@ long int initdram(int board_type) bcu4_testdram(dram_size); printf("%s %d MB of SDRAM\n", __FUNCTION__, dram_size/(1024*1024)); #endif + return dram_size; } - - diff --git a/board/netstal/hcu5/config.mk b/board/netstal/hcu5/config.mk index 58ec2af..cfd5744 100644 --- a/board/netstal/hcu5/config.mk +++ b/board/netstal/hcu5/config.mk @@ -28,4 +28,3 @@ PLATFORM_CPPFLAGS += -DCONFIG_440=1 ifeq ($(debug),1) PLATFORM_CPPFLAGS += -DDEBUG -g endif - diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c index 59107b9..23df081 100644 --- a/board/netstal/hcu5/hcu5.c +++ b/board/netstal/hcu5/hcu5.c @@ -29,12 +29,34 @@ void sysLedSet(u32 value); extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; -#define mtcpr0(reg, data) do { mtdcr(CPR0_CFGADDR,reg); \ - mtdcr(CPR0_CFGDATA,data); } while (0) -#define mfcpr0(reg, data) do { mtdcr(CPR0_CFGADDR,reg); \ - data = mfdcr(CPR0_CFGDATA); } while (0) +#undef BOOTSTRAP_OPTION_A_ACTIVE + +#define SDR0_CP440 0x0180 + +#define SYSTEM_RESET 0x30000000 +#define CHIP_RESET 0x20000000 + +#define SDR0_ECID0 0x0080 +#define SDR0_ECID1 0x0081 +#define SDR0_ECID2 0x0082 +#define SDR0_ECID3 0x0083 + +#define SYS_IO_ADDRESS 0xcce00000 + +#define DEFAULT_ETH_ADDR "ethaddr" +/* ethaddr for first or etha1ddr for second ethernet */ + +enum { + /* HW_GENERATION_HCU1 is no longer supported */ + HW_GENERATION_HCU2 = 0x10, + HW_GENERATION_HCU3 = 0x10, + HW_GENERATION_HCU4 = 0x20, + HW_GENERATION_HCU5 = 0x30, + HW_GENERATION_MCU = 0x08, + HW_GENERATION_MCU20 = 0x0a, + HW_GENERATION_MCU25 = 0x09, +}; -#define SDR0_CP440 0x0180 /* * This function is run very early, out of flash, and before devices are @@ -50,7 +72,6 @@ int board_early_init_f(void) { u32 reg; -#undef BOOTSTRAP_OPTION_A_ACTIVE #ifdef BOOTSTRAP_OPTION_A_ACTIVE /* Booting with Bootstrap Option A * First boot, with CPR0_ICFG_RLI_MASK == 0 @@ -64,27 +85,26 @@ int board_early_init_f(void) u32 cpr0icfg; u32 dbcr; - mfcpr0(CPR0_ICFG, cpr0icfg); - if ( ! (cpr0icfg & CPR0_ICFG_RLI_MASK ) ) { - mtcpr0(CPR0_MALD, 0x02000000); - mtcpr0(CPR0_OPBD, 0x02000000); - mtcpr0(CPR0_PERD, 0x05000000); /* 1:5 */ - mtcpr0(CPR0_PLLC, 0x40000238); - mtcpr0(CPR0_PLLD, 0x01010414); - mtcpr0(CPR0_PRIMAD, 0x01000000); - mtcpr0(CPR0_PRIMBD, 0x01000000); - mtcpr0(CPR0_SPCID, 0x03000000); - mtsdr(SDR0_PFC0, 0x00003E00); /* [CTE] = 0 */ - mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/ - mtcpr0(CPR0_ICFG, cpr0icfg | CPR0_ICFG_RLI_MASK); + + mfcpr(CPR0_ICFG, cpr0icfg); + if (!(cpr0icfg & CPR0_ICFG_RLI_MASK)) { + mtcpr(CPR0_MALD, 0x02000000); + mtcpr(CPR0_OPBD, 0x02000000); + mtcpr(CPR0_PERD, 0x05000000); /* 1:5 */ + mtcpr(CPR0_PLLC, 0x40000238); + mtcpr(CPR0_PLLD, 0x01010414); + mtcpr(CPR0_PRIMAD, 0x01000000); + mtcpr(CPR0_PRIMBD, 0x01000000); + mtcpr(CPR0_SPCID, 0x03000000); + mtsdr(SDR0_PFC0, 0x00003E00); /* [CTE] = 0 */ + mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/ + mtcpr(CPR0_ICFG, cpr0icfg | CPR0_ICFG_RLI_MASK); /* * Initiate system reset in debug control register DBCR */ dbcr = mfspr(dbcr0); - #define SYSTEM_RESET 0x30000000 - #define CHIP_RESET 0x20000000 - mtspr(dbcr0, dbcr | CHIP_RESET ); + mtspr(dbcr0, dbcr | CHIP_RESET); } mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/ #endif @@ -162,60 +182,42 @@ int board_early_init_f(void) return 0; } -#ifdef CONFIG_BOARD_PRE_INIT -int board_pre_init (void) +int board_pre_init(void) { - return board_early_init_f (); + return board_early_init_f(); } -#endif - -enum { - /* HW_GENERATION_HCU1 is no longer supported */ - HW_GENERATION_HCU2 = 0x10, - HW_GENERATION_HCU3 = 0x10, - HW_GENERATION_HCU4 = 0x20, - HW_GENERATION_HCU5 = 0x30, - HW_GENERATION_MCU = 0x08, - HW_GENERATION_MCU20 = 0x0a, - HW_GENERATION_MCU25 = 0x09, -}; - -int checkboard (void) +int checkboard(void) { -#define SDR0_ECID0 0x0080 -#define SDR0_ECID1 0x0081 -#define SDR0_ECID2 0x0082 -#define SDR0_ECID3 0x0083 - unsigned j; - uint16_t *hwVersReg = (uint16_t *) HCU_HW_VERSION_REGISTER; - uint16_t *boardVersReg = (uint16_t *) HCU_CPLD_VERSION_REGISTER; - uint16_t generation = *boardVersReg & 0xf0; - uint16_t index = *boardVersReg & 0x0f; - ulong ecid0, ecid1, ecid2, ecid3; - printf ("Netstal Maschinen AG: "); + unsigned int j; + u16 *hwVersReg = (u16 *) HCU_HW_VERSION_REGISTER; + u16 *boardVersReg = (u16 *) HCU_CPLD_VERSION_REGISTER; + u16 generation = *boardVersReg & 0xf0; + u16 index = *boardVersReg & 0x0f; + u32 ecid0, ecid1, ecid2, ecid3; + + printf("Netstal Maschinen AG: "); if (generation == HW_GENERATION_HCU3) - printf ("HCU3: index %d", index); + printf("HCU3: index %d", index); else if (generation == HW_GENERATION_HCU4) - printf ("HCU4: index %d", index); + printf("HCU4: index %d", index); else if (generation == HW_GENERATION_HCU5) - printf ("HCU5: index %d", index); - printf (" HW 0x%02x\n", *hwVersReg & 0xff); + printf("HCU5: index %d", index); + printf(" HW 0x%02x\n", *hwVersReg & 0xff); mfsdr(SDR0_ECID0, ecid0); mfsdr(SDR0_ECID1, ecid1); mfsdr(SDR0_ECID2, ecid2); mfsdr(SDR0_ECID3, ecid3); - printf("Chip ID 0x%x 0x%x 0x%x 0x%x\n", ecid0, ecid1, ecid2, ecid3); - for (j=0; j < 6;j++) { + printf("Chip ID 0x%x 0x%x 0x%x 0x%x\n", ecid0, ecid1, ecid2, ecid3); + for (j = 0;j < 6; j++) { sysLedSet(1 << j); - udelay(200*1000); + udelay(200 * 1000); } + return 0; } -#define SYS_IO_ADDRESS 0xcce00000 - u32 sysLedGet(void) { return in16(SYS_IO_ADDRESS) & 0x3f; @@ -232,9 +234,10 @@ void sysLedSet(u32 value /* value to place in LEDs */) static u32 getSerialNr(void) { u32 *serial = (u32 *)CFG_FLASH_BASE; - if (*serial == 0xffffffff) { + + if (*serial == 0xffffffff) return get_ticks(); - } + return *serial; } @@ -242,45 +245,44 @@ static u32 getSerialNr(void) /*---------------------------------------------------------------------------+ * misc_init_r. *---------------------------------------------------------------------------*/ - -#define DEFAULT_ETH_ADDR "ethaddr" -/* ethaddr for first or etha1ddr for second ethernet */ - int misc_init_r(void) { char *s = getenv(DEFAULT_ETH_ADDR); char *e; int i; - u32 serial = getSerialNr(); + u32 serial = getSerialNr(); unsigned long usb2d0cr = 0; unsigned long usb2phy0cr, usb2h0cr = 0; unsigned long sdr0_pfc1; for (i = 0; i < 6; ++i) { - gd->bd->bi_enetaddr[i] = s ? simple_strtoul (s, &e, 16) : 0; + gd->bd->bi_enetaddr[i] = s ? simple_strtoul(s, &e, 16) : 0; if (s) s = (*e) ? e + 1 : e; } + if (gd->bd->bi_enetaddr[3] == 0 && gd->bd->bi_enetaddr[4] == 0 && gd->bd->bi_enetaddr[5] == 0) { char ethaddr[22]; + /* Must be in sync with CONFIG_ETHADDR */ gd->bd->bi_enetaddr[0] = 0x00; gd->bd->bi_enetaddr[1] = 0x60; gd->bd->bi_enetaddr[2] = 0x13; - gd->bd->bi_enetaddr[3] = (serial >> 16) & 0xff; - gd->bd->bi_enetaddr[4] = (serial >> 8) & 0xff; + gd->bd->bi_enetaddr[3] = (serial >> 16) & 0xff; + gd->bd->bi_enetaddr[4] = (serial >> 8) & 0xff; /* byte[5].bit 0 must be zero */ - gd->bd->bi_enetaddr[5] = (serial >> 0) & 0xfe; - sprintf (ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X\0", - gd->bd->bi_enetaddr[0], gd->bd->bi_enetaddr[1], - gd->bd->bi_enetaddr[2], gd->bd->bi_enetaddr[3], - gd->bd->bi_enetaddr[4], gd->bd->bi_enetaddr[5]) ; + gd->bd->bi_enetaddr[5] = (serial >> 0) & 0xfe; + sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X\0", + gd->bd->bi_enetaddr[0], gd->bd->bi_enetaddr[1], + gd->bd->bi_enetaddr[2], gd->bd->bi_enetaddr[3], + gd->bd->bi_enetaddr[4], gd->bd->bi_enetaddr[5]) ; printf("%s: Setting eth %s serial 0x%x\n", __FUNCTION__, ethaddr, serial); - setenv (DEFAULT_ETH_ADDR, ethaddr); + setenv(DEFAULT_ETH_ADDR, ethaddr); } + #ifdef CFG_ENV_IS_IN_FLASH /* Monitor protection ON by default */ (void)flash_protect(FLAG_PROTECT_SET, @@ -334,9 +336,9 @@ int misc_init_r(void) mtsdr(SDR0_USB2H0CR, usb2h0cr); /*clear resets*/ - udelay (1000); + udelay(1000); mtsdr(SDR0_SRST1, 0x00000000); - udelay (1000); + udelay(1000); mtsdr(SDR0_SRST0, 0x00000000); printf("USB: Host(int phy) Device(ext phy)\n"); @@ -356,7 +358,7 @@ int misc_init_r(void) * certain pre-initialization actions. * ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) +#if defined(CONFIG_PCI) int pci_pre_init(struct pci_controller *hose) { unsigned long addr; @@ -374,7 +376,7 @@ int pci_pre_init(struct pci_controller *hose) mfsdr(sdr_amp1, addr); mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00); addr = mfdcr(plb3_acr); - // mtdcr(plb3_acr, addr & ~plb1_acr_wrp_mask); /* ngngng */ + /* mtdcr(plb3_acr, addr & ~plb1_acr_wrp_mask); */ /* ngngng */ mtdcr(plb3_acr, addr | 0x80000000); /* Sequoia */ /*-------------------------------------------------------------------+ @@ -383,7 +385,7 @@ int pci_pre_init(struct pci_controller *hose) mfsdr(sdr_amp0, addr); mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00); addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */ -// mtdcr(plb4_acr, addr & ~plb1_acr_wrp_mask); /* ngngng */ + /* mtdcr(plb4_acr, addr & ~plb1_acr_wrp_mask); */ /* ngngng */ mtdcr(plb4_acr, addr); /* Sequoia */ /*-------------------------------------------------------------------+ @@ -393,24 +395,23 @@ int pci_pre_init(struct pci_controller *hose) addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair; addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled; addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep; -// addr = (addr & ~plb0_acr_wrp_mask) ; /* ngngng */ + /* addr = (addr & ~plb0_acr_wrp_mask); */ /* ngngng */ addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; /* Sequoia */ - // mtdcr(plb0_acr, addr); /* Sequoia */ - mtdcr(plb0_acr, 0); // PATCH HAB: WRITE PIPELINING OFF - + /* mtdcr(plb0_acr, addr); */ /* Sequoia */ + mtdcr(plb0_acr, 0); /* PATCH HAB: WRITE PIPELINING OFF */ /* Segment1 */ addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair; addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled; addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep; addr = (addr & ~plb1_acr_wrp_mask) ; - // mtdcr(plb1_acr, addr); /* Sequoia */ - mtdcr(plb1_acr, 0); // PATCH HAB: WRITE PIPELINING OFF + /* mtdcr(plb1_acr, addr); */ /* Sequoia */ + mtdcr(plb1_acr, 0); /* PATCH HAB: WRITE PIPELINING OFF */ return 1; } -#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */ +#endif /* defined(CONFIG_PCI) */ /************************************************************************* * pci_target_init @@ -476,7 +477,6 @@ void pci_target_init(struct pci_controller *hose) pci_write_config_word(0, PCI_ERREN, 0); pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); - } #endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ @@ -523,4 +523,3 @@ int is_pci_host(struct pci_controller *hose) return 1; } #endif /* defined(CONFIG_PCI) */ - diff --git a/board/netstal/hcu5/init.S b/board/netstal/hcu5/init.S index 6da5f22..5ab6cd2 100644 --- a/board/netstal/hcu5/init.S +++ b/board/netstal/hcu5/init.S @@ -55,7 +55,7 @@ tlbtab: tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I ) /* TLB-entry for EBC (CFG_CPLD) */ - // tlbentry( CFG_CPLD, SZ_1K, CFG_CPLD, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + /* tlbentry( CFG_CPLD, SZ_1K, CFG_CPLD, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) */ /* CAN */ tlbentry( CFG_CS_1, SZ_16M, CFG_CS_1, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) /* IMC + CPLD */ @@ -77,5 +77,3 @@ tlbtab: /* TLB for SDRAM will be added by initdram (sdram.c) */ tlbtab_end - - diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c index f7d6865..4039195 100644 --- a/board/netstal/hcu5/sdram.c +++ b/board/netstal/hcu5/sdram.c @@ -216,8 +216,9 @@ long int initdram (int board_type) { #define HCU_HW_SDRAM_CONFIG_MASK 0x7 #define INVALID_HW_CONFIG "Invalid HW-Config" - uint16_t *hwVersReg = (uint16_t *) HCU_HW_VERSION_REGISTER; - unsigned int dram_size=0; + u16 *hwVersReg = (u16 *) HCU_HW_VERSION_REGISTER; + unsigned int dram_size = 0; + mtsdram(DDR0_02, 0x00000000); /* Values must be kept in sync with Excel-table <> ! */ @@ -229,15 +230,15 @@ long int initdram (int board_type) switch (*hwVersReg & HCU_HW_SDRAM_CONFIG_MASK) { case 0: dram_size = 128 * 1024 * 1024 ; - mtsdram(DDR0_06, 0x0102C80D); // 128MB RAM - mtsdram(DDR0_11, 0x000FC800); // 128MB RAM - mtsdram(DDR0_43, 0x030A0300); // 128MB RAM + mtsdram(DDR0_06, 0x0102C80D); /* 128MB RAM */ + mtsdram(DDR0_11, 0x000FC800); /* 128MB RAM */ + mtsdram(DDR0_43, 0x030A0300); /* 128MB RAM */ break; case 1: dram_size = 256 * 1024 * 1024 ; - mtsdram(DDR0_06, 0x0102C812); // 256MB RAM - mtsdram(DDR0_11, 0x0014C800); // 256MB RAM - mtsdram(DDR0_43, 0x030A0200); // 256MB RAM + mtsdram(DDR0_06, 0x0102C812); /* 256MB RAM */ + mtsdram(DDR0_11, 0x0014C800); /* 256MB RAM */ + mtsdram(DDR0_43, 0x030A0200); /* 256MB RAM */ break; default: sdram_panic(INVALID_HW_CONFIG); @@ -245,8 +246,10 @@ long int initdram (int board_type) } dram_size -= 16 * 1024 * 1024; mtsdram(DDR0_07, 0x00090100); - // TCPD=200 cycles of clock input is required to lock the DLL. - // CKE must be HIGH the entire time.mtsdram(DDR0_08, 0x02C80001); + /* + * TCPD=200 cycles of clock input is required to lock the DLL. + * CKE must be HIGH the entire time.mtsdram(DDR0_08, 0x02C80001); + */ mtsdram(DDR0_08, 0x02C80001); mtsdram(DDR0_09, 0x00011D5F); mtsdram(DDR0_10, 0x00000100); -- cgit v1.1