From 97549cb54615ebddff03da8511a83d3855979ef6 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Beno=C3=AEt=20Th=C3=A9baudeau?= Date: Fri, 3 May 2013 10:32:16 +0000 Subject: imx: tx25: Convert to iomux-v3 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau --- board/karo/tx25/tx25.c | 107 +++++++++++++++++++++++++++++++------------------ 1 file changed, 68 insertions(+), 39 deletions(-) (limited to 'board/karo/tx25') diff --git a/board/karo/tx25/tx25.c b/board/karo/tx25/tx25.c index 85719a0..2952eba 100644 --- a/board/karo/tx25/tx25.c +++ b/board/karo/tx25/tx25.c @@ -27,9 +27,8 @@ #include #include #include -#include +#include #include -#include DECLARE_GLOBAL_DATA_PTR; @@ -42,36 +41,44 @@ void board_init_f(ulong bootflag) #endif #ifdef CONFIG_FEC_MXC +/* + * FIXME: need to revisit this + * The original code enabled PUE and 100-k pull-down without PKE, so the right + * value here is likely: + * 0 for no pull + * or: + * PAD_CTL_PUS_100K_DOWN for 100-k pull-down + */ +#define FEC_OUT_PAD_CTRL 0 + #define GPIO_FEC_RESET_B IMX_GPIO_NR(4, 7) #define GPIO_FEC_ENABLE_B IMX_GPIO_NR(4, 9) void tx25_fec_init(void) { - struct iomuxc_mux_ctl *muxctl; - struct iomuxc_pad_ctl *padctl; - u32 gpio_mux_mode = MX25_PIN_MUX_MODE(5); - u32 saved_rdata0_mode, saved_rdata1_mode, saved_rx_dv_mode; + static const iomux_v3_cfg_t fec_pads[] = { + MX25_PAD_FEC_TX_CLK__FEC_TX_CLK, + MX25_PAD_FEC_RX_DV__FEC_RX_DV, + MX25_PAD_FEC_RDATA0__FEC_RDATA0, + NEW_PAD_CTRL(MX25_PAD_FEC_TDATA0__FEC_TDATA0, FEC_OUT_PAD_CTRL), + NEW_PAD_CTRL(MX25_PAD_FEC_TX_EN__FEC_TX_EN, FEC_OUT_PAD_CTRL), + NEW_PAD_CTRL(MX25_PAD_FEC_MDC__FEC_MDC, FEC_OUT_PAD_CTRL), + MX25_PAD_FEC_MDIO__FEC_MDIO, + MX25_PAD_FEC_RDATA1__FEC_RDATA1, + NEW_PAD_CTRL(MX25_PAD_FEC_TDATA1__FEC_TDATA1, FEC_OUT_PAD_CTRL), + + NEW_PAD_CTRL(MX25_PAD_D13__GPIO_4_7, 0), /* FEC_RESET_B */ + NEW_PAD_CTRL(MX25_PAD_D11__GPIO_4_9, 0), /* FEC_ENABLE_B */ + }; + + static const iomux_v3_cfg_t fec_cfg_pads[] = { + MX25_PAD_FEC_RDATA0__GPIO_3_10, + MX25_PAD_FEC_RDATA1__GPIO_3_11, + MX25_PAD_FEC_RX_DV__GPIO_3_12, + }; debug("tx25_fec_init\n"); - /* - * fec pin init is generic - */ - mx25_fec_init_pins(); - - /* - * Set up the FEC_RESET_B and FEC_ENABLE GPIO pins. - * - * FEC_RESET_B: gpio4[7] is ALT 5 mode of pin D13 - * FEC_ENABLE_B: gpio4[9] is ALT 5 mode of pin D11 - */ - muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE; - padctl = (struct iomuxc_pad_ctl *)IMX_IOPADCTL_BASE; - - writel(gpio_mux_mode, &muxctl->pad_d13); - writel(gpio_mux_mode, &muxctl->pad_d11); - - writel(0x0, &padctl->pad_d13); - writel(0x0, &padctl->pad_d11); + imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); /* drop PHY power and assert reset (low) */ gpio_direction_output(GPIO_FEC_RESET_B, 0); @@ -99,15 +106,10 @@ void tx25_fec_init(void) * RMII mode is selected by FEC_RX_DV which is GPIO 3_12 in mux mode */ /* - * save three current mux modes and set each to gpio mode + * set each mux mode to gpio mode */ - saved_rdata0_mode = readl(&muxctl->pad_fec_rdata0); - saved_rdata1_mode = readl(&muxctl->pad_fec_rdata1); - saved_rx_dv_mode = readl(&muxctl->pad_fec_rx_dv); - - writel(gpio_mux_mode, &muxctl->pad_fec_rdata0); - writel(gpio_mux_mode, &muxctl->pad_fec_rdata1); - writel(gpio_mux_mode, &muxctl->pad_fec_rx_dv); + imx_iomux_v3_setup_multiple_pads(fec_cfg_pads, + ARRAY_SIZE(fec_cfg_pads)); /* * set each to 1 and make each an output @@ -128,19 +130,46 @@ void tx25_fec_init(void) /* * set FEC pins back */ - writel(saved_rdata0_mode, &muxctl->pad_fec_rdata0); - writel(saved_rdata1_mode, &muxctl->pad_fec_rdata1); - writel(saved_rx_dv_mode, &muxctl->pad_fec_rx_dv); + imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); } #else #define tx25_fec_init() #endif -int board_init() -{ #ifdef CONFIG_MXC_UART - mx25_uart1_init_pins(); +/* + * Set up input pins with hysteresis and 100-k pull-ups + */ +#define UART1_IN_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP) +/* + * FIXME: need to revisit this + * The original code enabled PUE and 100-k pull-down without PKE, so the right + * value here is likely: + * 0 for no pull + * or: + * PAD_CTL_PUS_100K_DOWN for 100-k pull-down + */ +#define UART1_OUT_PAD_CTRL 0 + +static void tx25_uart1_init(void) +{ + static const iomux_v3_cfg_t uart1_pads[] = { + NEW_PAD_CTRL(MX25_PAD_UART1_RXD__UART1_RXD, UART1_IN_PAD_CTRL), + NEW_PAD_CTRL(MX25_PAD_UART1_TXD__UART1_TXD, UART1_OUT_PAD_CTRL), + NEW_PAD_CTRL(MX25_PAD_UART1_RTS__UART1_RTS, UART1_OUT_PAD_CTRL), + NEW_PAD_CTRL(MX25_PAD_UART1_CTS__UART1_CTS, UART1_IN_PAD_CTRL), + }; + + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} +#else +#define tx25_uart1_init() #endif + +int board_init() +{ + tx25_uart1_init(); + /* board id for linux */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; return 0; -- cgit v1.1