From 9d407995516bfcd401b76de0c11e679fb3871c79 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Mon, 10 Jul 2006 23:07:28 +0200 Subject: Major PCMCIA Cleanup to make code better readable and maintainable. Notes: - Board-dependend code for RPXLITE and RPXCLASSIC-based boards placed to the drivers/rpx_pmcia.c file to avoid duplication. Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c). - drivers/i82365.c has been split into two parts located at board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are the only boards using CONFIG_82365). - Changes were tested for clean build and *very* *few* boards. --- board/c2mon/Makefile | 2 +- board/c2mon/pcmcia.c | 284 +++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 285 insertions(+), 1 deletion(-) create mode 100644 board/c2mon/pcmcia.c (limited to 'board/c2mon') diff --git a/board/c2mon/Makefile b/board/c2mon/Makefile index 7a2014d..7b2b545 100644 --- a/board/c2mon/Makefile +++ b/board/c2mon/Makefile @@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk LIB = lib$(BOARD).a -OBJS = $(BOARD).o flash.o +OBJS = $(BOARD).o flash.o pcmcia.o $(LIB): .depend $(OBJS) $(AR) crv $@ $(OBJS) diff --git a/board/c2mon/pcmcia.c b/board/c2mon/pcmcia.c new file mode 100644 index 0000000..5e50c4d --- /dev/null +++ b/board/c2mon/pcmcia.c @@ -0,0 +1,284 @@ +#include +#include +#include + +#undef CONFIG_PCMCIA + +#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) +#define CONFIG_PCMCIA +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD) +#define CONFIG_PCMCIA +#endif + +#ifdef CONFIG_PCMCIA + +#define PCMCIA_BOARD_MSG "C2MON" + +static void cfg_ports (void) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + ushort sreg; + + immap = (immap_t *)CFG_IMMR; + cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm)); + + /* + * Configure Port C for TPS2211 PC-Card Power-Interface Switch + * + * Switch off all voltages, assert shutdown + */ + sreg = immap->im_ioport.iop_pcdat; + sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1); /* VAVPP => Hi-Z */ + sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1); /* 3V and 5V off */ + immap->im_ioport.iop_pcdat = sreg; + + immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS); + immap->im_ioport.iop_pcdir |= TPS2211_OUTPUTS; + + debug ("Set Port C: PAR: %04x DIR: %04x DAT: %04x\n", + immap->im_ioport.iop_pcpar, + immap->im_ioport.iop_pcdir, + immap->im_ioport.iop_pcdat); + + /* + * Configure Port B for TPS2211 PC-Card Power-Interface Switch + * + * Over-Current Input only + */ + cp->cp_pbpar &= ~(TPS2211_INPUTS); + cp->cp_pbdir &= ~(TPS2211_INPUTS); + + debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n", + cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat); +} + +int pcmcia_hardware_enable(int slot) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + volatile pcmconf8xx_t *pcmp; + volatile sysconf8xx_t *sysp; + uint reg, pipr, mask; + ushort sreg; + int i; + + debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + udelay(10000); + + immap = (immap_t *)CFG_IMMR; + sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf)); + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm)); + + /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */ + cfg_ports (); + + /* + * Configure SIUMCR to enable PCMCIA port B + * (VFLS[0:1] are not used for debugging, we connect FRZ# instead) + */ + sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */ + + /* clear interrupt state, and disable interrupts */ + pcmp->pcmc_pscr = PCMCIA_MASK(_slot_); + pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_); + + /* + * Disable interrupts, DMA, and PCMCIA buffers + * (isolate the interface) and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + /* + * Make sure there is a card in the slot, then configure the interface. + */ + udelay(10000); + debug ("[%d] %s: PIPR(%p)=0x%x\n", + __LINE__,__FUNCTION__, + &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); + if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { + printf (" No Card found\n"); + return (1); + } + + /* + * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z + */ + mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot); + pipr = pcmp->pcmc_pipr; + debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", + pipr, + (reg&PCMCIA_VS1(slot))?"n":"ff", + (reg&PCMCIA_VS2(slot))?"n":"ff"); + + sreg = immap->im_ioport.iop_pcdat; + if ((pipr & mask) == mask) { + sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */ + TPS2211_VCCD1); /* 5V on */ + sreg &= ~(TPS2211_VCCD0); /* 3V off */ + puts (" 5.0V card found: "); + } else { + sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */ + TPS2211_VCCD0); /* 3V on */ + sreg &= ~(TPS2211_VCCD1); /* 5V off */ + puts (" 3.3V card found: "); + } + + debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n", + sreg, + ( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off", + (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) ? "on" : "off" + ); + + immap->im_ioport.iop_pcdat = sreg; + + /* Wait 500 ms; use this to check for over-current */ + for (i=0; i<5000; ++i) { + if ((cp->cp_pbdat & TPS2211_OC) == 0) { + printf (" *** Overcurrent - Safety shutdown ***\n"); + immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1); + return (1); + } + udelay (100); + } + + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + + udelay(250000); /* some cards need >150 ms to come up :-( */ + + debug ("# hardware_enable done\n"); + + return (0); +} + + +#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) +int pcmcia_hardware_disable(int slot) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + volatile pcmconf8xx_t *pcmp; + u_long reg; + + debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot); + + immap = (immap_t *)CFG_IMMR; + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + + /* Configure PCMCIA General Control Register */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = 0; + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + + /* ALl voltages off / Hi-Z */ + immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 | + TPS2211_VCCD0 | TPS2211_VCCD1 ); + + udelay(10000); + + return (0); +} +#endif /* CFG_CMD_PCMCIA */ + + +int pcmcia_voltage_set(int slot, int vcc, int vpp) +{ + volatile immap_t *immap; + volatile cpm8xx_t *cp; + volatile pcmconf8xx_t *pcmp; + u_long reg; + ushort sreg; + + debug ("voltage_set: " + PCMCIA_BOARD_MSG + " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n", + 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10); + + immap = (immap_t *)CFG_IMMR; + cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm)); + pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); + /* + * Disable PCMCIA buffers (isolate the interface) + * and assert RESET signal + */ + debug ("Disable PCMCIA buffers and assert RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + /* + * Configure Port C pins for + * 5 Volts Enable and 3 Volts enable, + * Turn all power pins to Hi-Z + */ + debug ("PCMCIA power OFF\n"); + cfg_ports (); /* Enables switch, but all in Hi-Z */ + + sreg = immap->im_ioport.iop_pcdat; + sreg |= TPS2211_VPPD0 | TPS2211_VPPD1; /* VAVPP always Hi-Z */ + + switch(vcc) { + case 0: break; /* Switch off */ + case 33: sreg |= TPS2211_VCCD0; /* Switch on 3.3V */ + sreg &= ~TPS2211_VCCD1; + break; + case 50: sreg &= ~TPS2211_VCCD0; /* Switch on 5.0V */ + sreg |= TPS2211_VCCD1; + break; + default: goto done; + } + + /* Checking supported voltages */ + + debug ("PIPR: 0x%x --> %s\n", + pcmp->pcmc_pipr, + (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V"); + + immap->im_ioport.iop_pcdat = sreg; + +#ifdef DEBUG +{ + char *s; + + if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) { + s = "at 3.3V"; + } else if (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) { + s = "at 5.0V"; + } else { + s = "down"; + } + printf ("PCMCIA powered %s\n", s); +} +#endif + +done: + debug ("Enable PCMCIA buffers and stop RESET\n"); + reg = PCMCIA_PGCRX(_slot_); + reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */ + reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */ + PCMCIA_PGCRX(_slot_) = reg; + udelay(500); + + debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", + slot+'A'); + return (0); +} + +#endif /* CONFIG_PCMCIA */ -- cgit v1.1