From d2f68006627eda6cb6c7f364bddf621dbfd2fc68 Mon Sep 17 00:00:00 2001 From: Eugene OBrien Date: Tue, 31 Jul 2007 10:24:56 +0200 Subject: ppc4xx: Update AMCC Bamboo 440EP support Changed storage type of cfg_simulate_spd_eeprom to const Changed storage type of gpio_tab to stack storage (Cannot access global data declarations in .bss until afer code relocation) Improved SDRAM tests to catch problems where data is not uniquely addressable (e.g. incorrectly programmed SDRAM row or columns) Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules Fixed AM29LV320DT (OpCode Flash) sector map Signed-off-by: Eugene OBrien Signed-off-by: Stefan Roese --- board/amcc/bamboo/bamboo.c | 321 ++++++++++++++++++++++++++++++------------- board/amcc/bamboo/init.S | 3 +- board/amcc/bamboo/u-boot.lds | 2 - board/amcc/common/flash.c | 18 ++- common/flash.c | 10 +- cpu/ppc4xx/44x_spd_ddr.c | 2 +- include/configs/bamboo.h | 2 + 7 files changed, 248 insertions(+), 110 deletions(-) diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c index caf6690..00c793a 100644 --- a/board/amcc/bamboo/bamboo.c +++ b/board/amcc/bamboo/bamboo.c @@ -32,9 +32,170 @@ void ext_bus_cntlr_init(void); void configure_ppc440ep_pins(void); int is_nand_selected(void); -unsigned char cfg_simulate_spd_eeprom[128]; +#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) +/************************************************************************* + * + * Bamboo has one bank onboard sdram (plus DIMM) + * + * Fixed memory is composed of : + * MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266, + * 13 row add bits, 10 column add bits (but 12 row used only). + * ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266, + * 12 row add bits, 10 column add bits. + * Prepare a subset (only the used ones) of SPD data + * + * Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of + * the corresponding bank is divided by 2 due to number of Row addresses + * 12 in the ECC module + * + * Assumes: 64 MB, ECC, non-registered + * PLB @ 133 MHz + * + ************************************************************************/ +const unsigned char cfg_simulate_spd_eeprom[128] = { + 0x80, /* number of SPD bytes used: 128 */ + 0x08, /* total number bytes in SPD device = 256 */ + 0x07, /* DDR ram */ +#ifdef CONFIG_DDR_ECC + 0x0C, /* num Row Addr: 12 */ +#else + 0x0D, /* num Row Addr: 13 */ +#endif + 0x09, /* numColAddr: 9 */ + 0x01, /* numBanks: 1 */ + 0x20, /* Module data width: 32 bits */ + 0x00, /* Module data width continued: +0 */ + 0x04, /* 2.5 Volt */ + 0x75, /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */ +#ifdef CONFIG_DDR_ECC + 0x02, /* ECC ON : 02 OFF : 00 */ +#else + 0x00, /* ECC ON : 02 OFF : 00 */ +#endif + 0x82, /* refresh Rate Type: Normal (15.625us) + Self refresh */ + 0, + 0, + 0, + 0x01, /* wcsbc = 1 */ + 0, + 0, + 0x0C, /* casBit (2,2.5) */ + 0, + 0, + 0x00, /* not registered: 0 registered : 0x02*/ + 0, + 0xA0, /* SDRAM Cycle Time (cas latency 2) = 10 ns */ + 0, + 0x00, /* SDRAM Cycle Time (cas latency 1.5) = N.A */ + 0, + 0x50, /* tRpNs = 20 ns */ + 0, + 0x50, /* tRcdNs = 20 ns */ + 45, /* tRasNs */ +#ifdef CONFIG_DDR_ECC + 0x08, /* bankSizeID: 32MB */ +#else + 0x10, /* bankSizeID: 64MB */ +#endif + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0 +}; +#endif -gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; #if 0 { /* GPIO Alternate1 Alternate2 Alternate3 */ { @@ -291,73 +452,12 @@ int checkboard(void) return (0); } -#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) -/************************************************************************* - * - * init_spd_array -- Bamboo has one bank onboard sdram (plus DIMM) - * - * Fixed memory is composed of : - * MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266, - * 13 row add bits, 10 column add bits (but 12 row used only). - * ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266, - * 12 row add bits, 10 column add bits. - * Prepare a subset (only the used ones) of SPD data - * - * Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of - * the corresponding bank is divided by 2 due to number of Row addresses - * 12 in the ECC module - * - * Assumes: 64 MB, ECC, non-registered - * PLB @ 133 MHz - * - ************************************************************************/ -static void init_spd_array(void) -{ - cfg_simulate_spd_eeprom[8] = 0x04; /* 2.5 Volt */ - cfg_simulate_spd_eeprom[2] = 0x07; /* DDR ram */ - -#ifdef CONFIG_DDR_ECC - cfg_simulate_spd_eeprom[11] = 0x02; /* ECC ON : 02 OFF : 00 */ - cfg_simulate_spd_eeprom[31] = 0x08; /* bankSizeID: 32MB */ - cfg_simulate_spd_eeprom[3] = 0x0C; /* num Row Addr: 12 */ -#else - cfg_simulate_spd_eeprom[11] = 0x00; /* ECC ON : 02 OFF : 00 */ - cfg_simulate_spd_eeprom[31] = 0x10; /* bankSizeID: 64MB */ - cfg_simulate_spd_eeprom[3] = 0x0D; /* num Row Addr: 13 */ -#endif - - cfg_simulate_spd_eeprom[4] = 0x09; /* numColAddr: 9 */ - cfg_simulate_spd_eeprom[5] = 0x01; /* numBanks: 1 */ - cfg_simulate_spd_eeprom[0] = 0x80; /* number of SPD bytes used: 128 */ - cfg_simulate_spd_eeprom[1] = 0x08; /* total number bytes in SPD device = 256 */ - cfg_simulate_spd_eeprom[21] = 0x00; /* not registered: 0 registered : 0x02*/ - cfg_simulate_spd_eeprom[6] = 0x20; /* Module data width: 32 bits */ - cfg_simulate_spd_eeprom[7] = 0x00; /* Module data width continued: +0 */ - cfg_simulate_spd_eeprom[15] = 0x01; /* wcsbc = 1 */ - cfg_simulate_spd_eeprom[27] = 0x50; /* tRpNs = 20 ns */ - cfg_simulate_spd_eeprom[29] = 0x50; /* tRcdNs = 20 ns */ - - cfg_simulate_spd_eeprom[30] = 45; /* tRasNs */ - - cfg_simulate_spd_eeprom[18] = 0x0C; /* casBit (2,2.5) */ - - cfg_simulate_spd_eeprom[9] = 0x75; /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */ - cfg_simulate_spd_eeprom[23] = 0xA0; /* SDRAM Cycle Time (cas latency 2) = 10 ns */ - cfg_simulate_spd_eeprom[25] = 0x00; /* SDRAM Cycle Time (cas latency 1.5) = N.A */ - cfg_simulate_spd_eeprom[12] = 0x82; /* refresh Rate Type: Normal (15.625us) + Self refresh */ -} -#endif long int initdram (int board_type) { #if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) long dram_size; - /* - * First write simulated values in eeprom array for onboard bank 0 - */ - init_spd_array(); - dram_size = spd_sdram(); return dram_size; @@ -371,11 +471,12 @@ int testdram(void) { unsigned long *mem = (unsigned long *)0; const unsigned long kend = (1024 / sizeof(unsigned long)); - unsigned long k, n; + unsigned long k, n, *p32, ctr; + const unsigned long bend = CFG_MBYTES_SDRAM * 1024 * 1024; mtmsr(0); - for (k = 0; k < CFG_KBYTES_SDRAM; + for (k = 0; k < CFG_MBYTES_SDRAM*1024; ++k, mem += (1024 / sizeof(unsigned long))) { if ((k & 1023) == 0) { printf("%3d MB\r", k / 1024); @@ -399,6 +500,34 @@ int testdram(void) } } } + + /* + * Perform a sequence test to ensure that all + * memory locations are uniquely addressable + */ + ctr = 0; + p32 = 0; + while ((unsigned long)p32 != bend) { + if (0 == ((unsigned long)p32 & ((1<<20)-1))) + printf("Writing %3d MB\r", (unsigned long)p32 >> 20); + *p32++ = ctr++; + } + + ctr = 0; + p32 = 0; + while ((unsigned long)p32 != bend) { + if (0 == ((unsigned long)p32 & ((1<<20)-1))) + printf("Verifying %3d MB\r", (unsigned long)p32 >> 20); + + if (*p32 != ctr) { + printf("SDRAM test fails at: %08x\n", p32); + return 1; + } + + ctr++; + p32++; + } + printf("SDRAM test passes\n"); return 0; } @@ -1211,7 +1340,7 @@ void uart_selection_in_fpga(uart_config_nb_t uart_config) /*----------------------------------------------------------------------------+ | init_default_gpio +----------------------------------------------------------------------------*/ -void init_default_gpio(void) +void init_default_gpio(gpio_param_s (*gpio_tab)[GPIO_MAX]) { int i; @@ -1281,7 +1410,7 @@ void init_default_gpio(void) | +----------------------------------------------------------------------------*/ -void update_uart_ios(uart_config_nb_t uart_config) +void update_uart_ios(uart_config_nb_t uart_config, gpio_param_s (*gpio_tab)[GPIO_MAX]) { switch (uart_config) { @@ -1409,7 +1538,7 @@ void update_uart_ios(uart_config_nb_t uart_config) /*----------------------------------------------------------------------------+ | update_ndfc_ios(void). +----------------------------------------------------------------------------*/ -void update_ndfc_ios(void) +void update_ndfc_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { /* Update GPIO Configuration Table */ gpio_tab[GPIO0][6].in_out = GPIO_OUT; /* EBC_CS_N(1) */ @@ -1427,7 +1556,7 @@ void update_ndfc_ios(void) /*----------------------------------------------------------------------------+ | update_zii_ios(void). +----------------------------------------------------------------------------*/ -void update_zii_ios(void) +void update_zii_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { /* Update GPIO Configuration Table */ gpio_tab[GPIO0][12].in_out = GPIO_IN; /* ZII_p0Rxd(0) */ @@ -1477,7 +1606,7 @@ void update_zii_ios(void) /*----------------------------------------------------------------------------+ | update_uic_0_3_irq_ios(). +----------------------------------------------------------------------------*/ -void update_uic_0_3_irq_ios(void) +void update_uic_0_3_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO1][8].in_out = GPIO_IN; /* UIC_IRQ(0) */ gpio_tab[GPIO1][8].alt_nb = GPIO_ALT1; @@ -1495,7 +1624,7 @@ void update_uic_0_3_irq_ios(void) /*----------------------------------------------------------------------------+ | update_uic_4_9_irq_ios(). +----------------------------------------------------------------------------*/ -void update_uic_4_9_irq_ios(void) +void update_uic_4_9_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO1][12].in_out = GPIO_IN; /* UIC_IRQ(4) */ gpio_tab[GPIO1][12].alt_nb = GPIO_ALT1; @@ -1516,7 +1645,7 @@ void update_uic_4_9_irq_ios(void) /*----------------------------------------------------------------------------+ | update_dma_a_b_ios(). +----------------------------------------------------------------------------*/ -void update_dma_a_b_ios(void) +void update_dma_a_b_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO1][12].in_out = GPIO_OUT; /* DMA_ACK(1) */ gpio_tab[GPIO1][12].alt_nb = GPIO_ALT2; @@ -1537,7 +1666,7 @@ void update_dma_a_b_ios(void) /*----------------------------------------------------------------------------+ | update_dma_c_d_ios(). +----------------------------------------------------------------------------*/ -void update_dma_c_d_ios(void) +void update_dma_c_d_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][0].in_out = GPIO_IN; /* DMA_REQ(2) */ gpio_tab[GPIO0][0].alt_nb = GPIO_ALT2; @@ -1562,7 +1691,7 @@ void update_dma_c_d_ios(void) /*----------------------------------------------------------------------------+ | update_ebc_master_ios(). +----------------------------------------------------------------------------*/ -void update_ebc_master_ios(void) +void update_ebc_master_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][27].in_out = GPIO_IN; /* EXT_EBC_REQ */ gpio_tab[GPIO0][27].alt_nb = GPIO_ALT1; @@ -1580,7 +1709,7 @@ void update_ebc_master_ios(void) /*----------------------------------------------------------------------------+ | update_usb2_device_ios(). +----------------------------------------------------------------------------*/ -void update_usb2_device_ios(void) +void update_usb2_device_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][26].in_out = GPIO_IN; /* USB2D_RXVALID */ gpio_tab[GPIO0][26].alt_nb = GPIO_ALT2; @@ -1611,20 +1740,21 @@ void update_usb2_device_ios(void) /*----------------------------------------------------------------------------+ | update_pci_patch_ios(). +----------------------------------------------------------------------------*/ -void update_pci_patch_ios(void) +void update_pci_patch_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* EBC_EXT_HDLA */ gpio_tab[GPIO0][29].alt_nb = GPIO_ALT1; } /*----------------------------------------------------------------------------+ - | set_chip_gpio_configuration(unsigned char gpio_core) + | set_chip_gpio_configuration(unsigned char gpio_core, + | gpio_param_s (*gpio_tab)[GPIO_MAX]) | Put the core impacted by clock modification and sharing in reset. | Config the select registers to resolve the sharing depending of the config. | Configure the GPIO registers. | +----------------------------------------------------------------------------*/ -void set_chip_gpio_configuration(unsigned char gpio_core) +void set_chip_gpio_configuration(unsigned char gpio_core, gpio_param_s (*gpio_tab)[GPIO_MAX]) { unsigned char i=0, j=0, reg_offset = 0; unsigned long gpio_reg, gpio_core_add; @@ -1778,11 +1908,12 @@ void configure_ppc440ep_pins(void) CORE_NOT_SELECTED /* PCI_PATCH */ }; + gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; /* Table Default Initialisation + FPGA Access */ - init_default_gpio(); - set_chip_gpio_configuration(GPIO0); - set_chip_gpio_configuration(GPIO1); + init_default_gpio(gpio_tab); + set_chip_gpio_configuration(GPIO0, gpio_tab); + set_chip_gpio_configuration(GPIO1, gpio_tab); /* Update Table */ force_bup_core_selection(ppc440ep_core_selection, &config_val); @@ -1817,7 +1948,7 @@ void configure_ppc440ep_pins(void) /* UIC 0:3 Selection */ if (ppc440ep_core_selection[UIC_0_3] == CORE_SELECTED) { - update_uic_0_3_irq_ios(); + update_uic_0_3_irq_ios(gpio_tab); dma_a_b_unselect_in_fpga(); } @@ -1825,21 +1956,21 @@ void configure_ppc440ep_pins(void) if (ppc440ep_core_selection[UIC_4_9] == CORE_SELECTED) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_UICIRQ5_SEL; - update_uic_4_9_irq_ios(); + update_uic_4_9_irq_ios(gpio_tab); } /* DMA AB Selection */ if (ppc440ep_core_selection[DMA_CHANNEL_AB] == CORE_SELECTED) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_DMAR_SEL; - update_dma_a_b_ios(); + update_dma_a_b_ios(gpio_tab); dma_a_b_selection_in_fpga(); } /* DMA CD Selection */ if (ppc440ep_core_selection[DMA_CHANNEL_CD] == CORE_SELECTED) { - update_dma_c_d_ios(); + update_dma_c_d_ios(gpio_tab); dma_c_d_selection_in_fpga(); } @@ -1848,14 +1979,14 @@ void configure_ppc440ep_pins(void) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_ERE_MASK) | SDR0_PFC1_ERE_EXTR_SEL; sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL; - update_ebc_master_ios(); + update_ebc_master_ios(gpio_tab); } /* PCI Patch Enable */ if (ppc440ep_core_selection[PCI_PATCH] == CORE_SELECTED) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL; - update_pci_patch_ios(); + update_pci_patch_ios(gpio_tab); } /* USB2 Host Selection - Not Implemented in PowerPC 440EP Pass1 */ @@ -1871,7 +2002,7 @@ void configure_ppc440ep_pins(void) /* USB2.0 Device Selection */ if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED) { - update_usb2_device_ios(); + update_usb2_device_ios(gpio_tab); sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL; sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE; @@ -1904,7 +2035,7 @@ void configure_ppc440ep_pins(void) /* NAND Flash Selection */ if (ppc440ep_core_selection[NAND_FLASH] == CORE_SELECTED) { - update_ndfc_ios(); + update_ndfc_ios(gpio_tab); #if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL | @@ -1933,7 +2064,7 @@ void configure_ppc440ep_pins(void) /* MII Selection */ if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED) { - update_zii_ios(); + update_zii_ios(gpio_tab); mfsdr(sdr_mfr, sdr0_mfr); sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII; mtsdr(sdr_mfr, sdr0_mfr); @@ -1944,7 +2075,7 @@ void configure_ppc440ep_pins(void) /* RMII Selection */ if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED) { - update_zii_ios(); + update_zii_ios(gpio_tab); mfsdr(sdr_mfr, sdr0_mfr); sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M; mtsdr(sdr_mfr, sdr0_mfr); @@ -1955,7 +2086,7 @@ void configure_ppc440ep_pins(void) /* SMII Selection */ if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED) { - update_zii_ios(); + update_zii_ios(gpio_tab); mfsdr(sdr_mfr, sdr0_mfr); sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII; mtsdr(sdr_mfr, sdr0_mfr); @@ -1992,7 +2123,7 @@ void configure_ppc440ep_pins(void) sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR; break; } - update_uart_ios(uart_configuration); + update_uart_ios(uart_configuration, gpio_tab); /* UART Selection in all cases */ uart_selection_in_fpga(uart_configuration); @@ -2014,8 +2145,8 @@ void configure_ppc440ep_pins(void) /* Perform effective access to hardware */ mtsdr(sdr_pfc1, sdr0_pfc1); - set_chip_gpio_configuration(GPIO0); - set_chip_gpio_configuration(GPIO1); + set_chip_gpio_configuration(GPIO0, gpio_tab); + set_chip_gpio_configuration(GPIO1, gpio_tab); /* USB2.0 Device Reset must be done after GPIO setting */ if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED) diff --git a/board/amcc/bamboo/init.S b/board/amcc/bamboo/init.S index 1459eec..f4d2ae3 100644 --- a/board/amcc/bamboo/init.S +++ b/board/amcc/bamboo/init.S @@ -51,13 +51,12 @@ tlbtab: tlbentry(CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G) #else tlbentry(CFG_NAND_BOOT_SPL_SRC, SZ_4K, CFG_NAND_BOOT_SPL_SRC, 0, AC_R|AC_W|AC_X|SA_G) + tlbentry(CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I) #endif /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ tlbentry(CFG_INIT_RAM_ADDR, SZ_4K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G) - tlbentry(CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I) - /* PCI base & peripherals */ tlbentry(CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I) diff --git a/board/amcc/bamboo/u-boot.lds b/board/amcc/bamboo/u-boot.lds index f6d7183..0375618 100644 --- a/board/amcc/bamboo/u-boot.lds +++ b/board/amcc/bamboo/u-boot.lds @@ -141,8 +141,6 @@ SECTIONS *(COMMON) } - ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); - _end = . ; PROVIDE (end = .); } diff --git a/board/amcc/common/flash.c b/board/amcc/common/flash.c index e6429ec..eba0511 100644 --- a/board/amcc/common/flash.c +++ b/board/amcc/common/flash.c @@ -745,19 +745,27 @@ static ulong flash_get_size_2(vu_long * addr, flash_info_t * info) if (info->flash_id & FLASH_BTYPE) { /* set sector offsets for bottom boot block type */ info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00004000; - info->start[2] = base + 0x00006000; - info->start[3] = base + 0x00008000; - for (i = 4; i < info->sector_count; i++) { + info->start[1] = base + 0x00002000; + info->start[2] = base + 0x00004000; + info->start[3] = base + 0x00006000; + info->start[4] = base + 0x00008000; + info->start[5] = base + 0x0000a000; + info->start[6] = base + 0x0000c000; + info->start[7] = base + 0x0000e000; + for (i = 8; i < info->sector_count; i++) { info->start[i] = - base + (i * 0x00010000) - 0x00030000; + base + ((i-7) * 0x00010000); } } else { /* set sector offsets for top boot block type */ i = info->sector_count - 1; + info->start[i--] = base + info->size - 0x00002000; info->start[i--] = base + info->size - 0x00004000; info->start[i--] = base + info->size - 0x00006000; info->start[i--] = base + info->size - 0x00008000; + info->start[i--] = base + info->size - 0x0000a000; + info->start[i--] = base + info->size - 0x0000c000; + info->start[i--] = base + info->size - 0x0000e000; for (; i >= 0; i--) { info->start[i] = base + i * 0x00010000; } diff --git a/common/flash.c b/common/flash.c index a64bc98..888ff9c 100644 --- a/common/flash.c +++ b/common/flash.c @@ -47,16 +47,16 @@ flash_protect (int flag, ulong from, ulong to, flash_info_t *info) short s_end = info->sector_count - 1; /* index of last sector */ int i; - debug ("flash_protect %s: from 0x%08lX to 0x%08lX\n", - (flag & FLAG_PROTECT_SET) ? "ON" : - (flag & FLAG_PROTECT_CLEAR) ? "OFF" : "???", - from, to); - /* Do nothing if input data is bad. */ if (info->sector_count == 0 || info->size == 0 || to < from) { return; } + debug ("flash_protect %s: from 0x%08lX to 0x%08lX\n", + (flag & FLAG_PROTECT_SET) ? "ON" : + (flag & FLAG_PROTECT_CLEAR) ? "OFF" : "???", + from, to); + /* There is nothing to do if we have no data about the flash * or the protect range and flash range don't overlap. */ diff --git a/cpu/ppc4xx/44x_spd_ddr.c b/cpu/ppc4xx/44x_spd_ddr.c index e5f296e..4a4c6f2 100644 --- a/cpu/ppc4xx/44x_spd_ddr.c +++ b/cpu/ppc4xx/44x_spd_ddr.c @@ -269,7 +269,7 @@ struct bank_param { typedef struct bank_param BANKPARMS; #ifdef CFG_SIMULATE_SPD_EEPROM -extern unsigned char cfg_simulate_spd_eeprom[128]; +extern const unsigned char cfg_simulate_spd_eeprom[128]; #endif static unsigned char spd_read(uchar chip, uint addr); diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index d58344d..4e00b9f 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -222,6 +222,8 @@ #define CFG_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */ #define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} #define CFG_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ +#define CONFIG_PROG_SDRAM_TLB +#undef CFG_DRAM_TEST /*----------------------------------------------------------------------- * I2C -- cgit v1.1