From ab5c80246e8e89e6f9b7f379aa9630a55586572e Mon Sep 17 00:00:00 2001 From: "Ye.Li" Date: Fri, 26 Sep 2014 14:07:48 +0800 Subject: ENGR00333317 imx: mx6sxsabreauto: Add BSP support for AI board Create mx6sx sabreauto BSP file and configurations. The devices below have been supported: 1. SD/MMC/eMMC on SDA/SDB (base board) sockets 2. USB OTG port and USB HOST port (base board) 3. NAND flash 4. QuadSPI flash on QSPI1 5. I2C 6. PMIC PFUZE100 7. Onboard ethernet chip on ENET2 8. Splash screen on LVDS Signed-off-by: Ye.Li --- board/freescale/mx6sxsabreauto/Makefile | 10 + board/freescale/mx6sxsabreauto/imximage.cfg | 161 +++++ board/freescale/mx6sxsabreauto/mx6sxsabreauto.c | 886 ++++++++++++++++++++++++ board/freescale/mx6sxsabreauto/plugin.S | 143 ++++ boards.cfg | 3 + include/configs/mx6sxsabreauto.h | 386 +++++++++++ 6 files changed, 1589 insertions(+) create mode 100644 board/freescale/mx6sxsabreauto/Makefile create mode 100644 board/freescale/mx6sxsabreauto/imximage.cfg create mode 100644 board/freescale/mx6sxsabreauto/mx6sxsabreauto.c create mode 100644 board/freescale/mx6sxsabreauto/plugin.S create mode 100644 include/configs/mx6sxsabreauto.h diff --git a/board/freescale/mx6sxsabreauto/Makefile b/board/freescale/mx6sxsabreauto/Makefile new file mode 100644 index 0000000..db01364 --- /dev/null +++ b/board/freescale/mx6sxsabreauto/Makefile @@ -0,0 +1,10 @@ +# (C) Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := mx6sxsabreauto.o + +extra-$(CONFIG_USE_PLUGIN) := plugin.bin +$(obj)/plugin.bin: $(obj)/plugin.o + $(OBJCOPY) -O binary --gap-fill 0xff $< $@ diff --git a/board/freescale/mx6sxsabreauto/imximage.cfg b/board/freescale/mx6sxsabreauto/imximage.cfg new file mode 100644 index 0000000..d431a2d --- /dev/null +++ b/board/freescale/mx6sxsabreauto/imximage.cfg @@ -0,0 +1,161 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +#define __ASSEMBLY__ +#include + +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi/sd/nand/onenand, qspi/nor + */ + +#ifdef CONFIG_SYS_BOOT_QSPI +BOOT_FROM qspi +#elif defined(CONFIG_SYS_BOOT_EIMNOR) +BOOT_FROM nor +#else +BOOT_FROM sd +#endif + +#ifdef CONFIG_USE_PLUGIN +/*PLUGIN plugin-binary-file IRAM_FREE_START_ADDR*/ +PLUGIN board/freescale/mx6sxsabreauto/plugin.bin 0x00907000 +#else + +#ifdef CONFIG_SECURE_BOOT +CSF 0x2000 +#endif + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* Enable all clocks */ +DATA 4 0x020c4068 0xffffffff +DATA 4 0x020c406c 0xffffffff +DATA 4 0x020c4070 0xffffffff +DATA 4 0x020c4074 0xffffffff +DATA 4 0x020c4078 0xffffffff +DATA 4 0x020c407c 0xffffffff +DATA 4 0x020c4080 0xffffffff +DATA 4 0x020c4084 0xffffffff + +/* IOMUX */ +/* DDR IO TYPE */ +DATA 4 0x020e0618 0x000c0000 +DATA 4 0x020e05fc 0x00000000 + +/* CLOCK */ +DATA 4 0x020e032c 0x00000030 + +/* ADDRESS */ +DATA 4 0x020e0300 0x00000030 +DATA 4 0x020e02fc 0x00000030 +DATA 4 0x020e05f4 0x00000030 + +/* CONTROL */ +DATA 4 0x020e0340 0x00000030 + +DATA 4 0x020e0320 0x00000000 +DATA 4 0x020e0310 0x00000030 +DATA 4 0x020e0314 0x00000030 +DATA 4 0x020e0614 0x00000030 + +/* DATA STROBE */ +DATA 4 0x020e05f8 0x00020000 +DATA 4 0x020e0330 0x00000030 +DATA 4 0x020e0334 0x00000030 +DATA 4 0x020e0338 0x00000030 +DATA 4 0x020e033c 0x00000030 + +/* DATA */ +DATA 4 0x020e0608 0x00020000 +DATA 4 0x020e060c 0x00000030 +DATA 4 0x020e0610 0x00000030 +DATA 4 0x020e061c 0x00000030 +DATA 4 0x020e0620 0x00000030 +DATA 4 0x020e02ec 0x00000030 +DATA 4 0x020e02f0 0x00000030 +DATA 4 0x020e02f4 0x00000030 +DATA 4 0x020e02f8 0x00000030 + +/* Calibrations */ +/* ZQ */ +DATA 4 0x021b0800 0xa1390003 +/* write leveling */ +DATA 4 0x021b080c 0x002C003D +DATA 4 0x021b0810 0x00110046 + +/* DQS Read Gate */ +DATA 4 0x021b083c 0x4160016C +DATA 4 0x021b0840 0x013C016C + +/* Read/Write Delay */ +DATA 4 0x021b0848 0x46424446 +DATA 4 0x021b0850 0x3A3C3C3A + +DATA 4 0x021b08c0 0x2492244A + +/* read data bit delay */ +DATA 4 0x021b081c 0x33333333 +DATA 4 0x021b0820 0x33333333 +DATA 4 0x021b0824 0x33333333 +DATA 4 0x021b0828 0x33333333 + +/* Complete calibration by forced measurment */ +DATA 4 0x021b08b8 0x00000800 + +/* MMDC init */ +/* in DDR3, 64-bit mode, only MMDC0 is initiated */ +DATA 4 0x021b0004 0x0002002d +DATA 4 0x021b0008 0x00333030 +DATA 4 0x021b000c 0x676b52f3 +DATA 4 0x021b0010 0xb66d8b63 +DATA 4 0x021b0014 0x01ff00db +DATA 4 0x021b0018 0x00011740 +DATA 4 0x021b001c 0x00008000 +DATA 4 0x021b002c 0x000026d2 +DATA 4 0x021b0030 0x006b1023 +DATA 4 0x021b0040 0x0000007f +DATA 4 0x021b0000 0x85190000 + +/* Initialize CS0: MT41K256M16HA-125 */ +/* MR2 */ +DATA 4 0x021b001c 0x04008032 +/* MR3 */ +DATA 4 0x021b001c 0x00008033 +/* MR1 */ +DATA 4 0x021b001c 0x00068031 +/* MR0 */ +DATA 4 0x021b001c 0x05208030 +/* DDR device ZQ calibration */ +DATA 4 0x021b001c 0x04008040 + +/* final DDR setup, before operation start */ +DATA 4 0x021b0020 0x00000800 +DATA 4 0x021b0818 0x00022227 +DATA 4 0x021b0004 0x0002556d +DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b001c 0x00000000 + +#endif diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c new file mode 100644 index 0000000..5785255 --- /dev/null +++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c @@ -0,0 +1,886 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#ifdef CONFIG_SYS_I2C_MXC +#include +#include +#endif +#ifdef CONFIG_MXC_RDC +#include +#include +#endif + +#ifdef CONFIG_VIDEO_MXS +#include +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ + PAD_CTL_SPEED_HIGH | \ + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST) + +#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) + +#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) + +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) + +#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ + PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm) + +#define BUTTON_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_DSE_40ohm) + +#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP) +#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \ + PAD_CTL_SRE_FAST) +#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1) + + +#ifdef CONFIG_SYS_I2C_MXC +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +/* I2C2 for PMIC */ +struct i2c_pads_info i2c_pad_info2 = { + .scl = { + .i2c_mode = MX6SX_PAD_GPIO1_IO02__I2C2_SCL | PC, + .gpio_mode = MX6SX_PAD_GPIO1_IO02__GPIO1_IO_2 | PC, + .gp = IMX_GPIO_NR(1, 2), + }, + .sda = { + .i2c_mode = MX6SX_PAD_GPIO1_IO03__I2C2_SDA | PC, + .gpio_mode = MX6SX_PAD_GPIO1_IO03__GPIO1_IO_3 | PC, + .gp = IMX_GPIO_NR(1, 3), + }, +}; + +/* I2C3 */ +struct i2c_pads_info i2c_pad_info3 = { + .scl = { + .i2c_mode = MX6SX_PAD_KEY_COL4__I2C3_SCL | PC, + .gpio_mode = MX6SX_PAD_KEY_COL4__GPIO2_IO_14 | PC, + .gp = IMX_GPIO_NR(2, 14), + }, + .sda = { + .i2c_mode = MX6SX_PAD_KEY_ROW4__I2C3_SDA | PC, + .gpio_mode = MX6SX_PAD_KEY_ROW4__GPIO2_IO_19 | PC, + .gp = IMX_GPIO_NR(2, 19), + }, +}; +#endif + +int dram_init(void) +{ + gd->ram_size = PHYS_SDRAM_SIZE; + + return 0; +} + +static iomux_v3_cfg_t const uart1_pads[] = { + MX6SX_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6SX_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc3_pads[] = { + MX6SX_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + + /* CD pin */ + MX6SX_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* RST_B, used for power reset cycle */ + MX6SX_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc4_pads[] = { + MX6SX_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + + /* CD pin */ + MX6SX_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +#ifdef CONFIG_FEC_MXC +static iomux_v3_cfg_t const fec1_pads[] = { + MX6SX_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), +}; + +static iomux_v3_cfg_t const fec2_pads[] = { + MX6SX_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), +}; + +static void setup_iomux_fec(int fec_id) +{ + if (0 == fec_id) + imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads)); + else + imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads)); +} +#endif + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} + +#ifdef CONFIG_QSPI + +#define QSPI_PAD_CTRL1 \ + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ + PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) + +static iomux_v3_cfg_t const quadspi_pads[] = { + MX6SX_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1A_SCLK__QSPI1_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1B_SCLK__QSPI1_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6SX_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), +}; + +int board_qspi_init(void) +{ + /* Set the iomux */ + imx_iomux_v3_setup_multiple_pads(quadspi_pads, ARRAY_SIZE(quadspi_pads)); + + /* Set the clock */ + enable_qspi_clk(0); + + return 0; +} +#endif + +#ifdef CONFIG_SYS_USE_NAND +iomux_v3_cfg_t gpmi_pads[] = { + MX6SX_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL0), + MX6SX_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6SX_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), +}; + +static void setup_gpmi_nand(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* config gpmi nand iomux */ + imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads)); + + /* config gpmi and bch clock to 100 MHz */ + clrsetbits_le32(&mxc_ccm->cs2cdr, + MXC_CCM_CS2CDR_QSPI2_CLK_PODF_MASK | + MXC_CCM_CS2CDR_QSPI2_CLK_PRED_MASK | + MXC_CCM_CS2CDR_QSPI2_CLK_SEL_MASK, + MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) | + MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) | + MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3)); + + /* enable gpmi and bch clock gating */ + setbits_le32(&mxc_ccm->CCGR4, + MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK | + MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK); + + /* enable apbh clock gating */ + setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK); +} +#endif + + +#ifdef CONFIG_FSL_ESDHC +static struct fsl_esdhc_cfg usdhc_cfg[3] = { + {USDHC3_BASE_ADDR}, + {USDHC4_BASE_ADDR}, +}; + +#define USDHC3_CD_GPIO IMX_GPIO_NR(7, 10) +#define USDHC3_RST_GPIO IMX_GPIO_NR(2, 11) +#define USDHC4_CD_GPIO IMX_GPIO_NR(7, 11) + +int mmc_get_env_devno(void) +{ + u32 soc_sbmr = readl(SRC_BASE_ADDR + 0x4); + int dev_no; + u32 bootsel; + + bootsel = (soc_sbmr & 0x000000FF) >> 6 ; + + /* If not boot from sd/mmc, use default value */ + if (bootsel != 1) + return CONFIG_SYS_MMC_ENV_DEV; + + /* BOOT_CFG2[3] and BOOT_CFG2[4] */ + dev_no = (soc_sbmr & 0x00001800) >> 11; + + /* need ubstract 1 to map to the mmc device id + * see the comments in board_mmc_init function + */ + + dev_no -= 2; + + return dev_no; +} + +int mmc_map_to_kernel_blk(int dev_no) +{ + return dev_no + 2; +} + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC3_BASE_ADDR: + ret = !gpio_get_value(USDHC3_CD_GPIO); + break; + case USDHC4_BASE_ADDR: + ret = !gpio_get_value(USDHC4_CD_GPIO); + break; + } + + return ret; + +} + +int board_mmc_init(bd_t *bis) +{ + int i; + + /* + * According to the board_mmc_init() the following map is done: + * (U-boot device node) (Physical Port) + * mmc0 USDHC3 + * mmc1 USDHC4 + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + imx_iomux_v3_setup_multiple_pads( + usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + gpio_direction_input(USDHC3_CD_GPIO); + + /* Need to set steer to B0 to A*/ + gpio_direction_output(USDHC3_RST_GPIO, 1); + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + break; + case 1: + imx_iomux_v3_setup_multiple_pads( + usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); + gpio_direction_input(USDHC4_CD_GPIO); + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); + break; + default: + printf("Warning: you configured more USDHC controllers" + "(%d) than supported by the board\n", i + 1); + return 0; + } + + if (fsl_esdhc_initialize(bis, &usdhc_cfg[i])) + printf("Warning: failed to initialize mmc dev %d\n", i); + } + + return 0; +} + +int check_mmc_autodetect(void) +{ + char *autodetect_str = getenv("mmcautodetect"); + + if ((autodetect_str != NULL) && + (strcmp(autodetect_str, "yes") == 0)) { + return 1; + } + + return 0; +} + +void board_late_mmc_init(void) +{ + char cmd[32]; + char mmcblk[32]; + u32 dev_no = mmc_get_env_devno(); + + if (!check_mmc_autodetect()) + return; + + setenv_ulong("mmcdev", dev_no); + + /* Set mmcblk env */ + sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw", + mmc_map_to_kernel_blk(dev_no)); + setenv("mmcroot", mmcblk); + + sprintf(cmd, "mmc dev %d", dev_no); + run_command(cmd, 0); +} + +#endif + +#ifdef CONFIG_VIDEO_MXS +static iomux_v3_cfg_t const lvds_ctrl_pads[] = { + /* Use GPIO for Brightness adjustment, duty cycle = period */ + MX6SX_PAD_SD1_DATA1__GPIO6_IO_3 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const lcd_pads[] = { + MX6SX_PAD_LCD1_CLK__LCDIF1_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17 | MUX_PAD_CTRL(LCD_PAD_CTRL), + MX6SX_PAD_LCD1_RESET__GPIO3_IO_27 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + + +struct lcd_panel_info_t { + unsigned int lcdif_base_addr; + int depth; + void (*enable)(struct lcd_panel_info_t const *dev); + struct fb_videomode mode; +}; + +void do_enable_lvds(struct lcd_panel_info_t const *dev) +{ + enable_lcdif_clock(dev->lcdif_base_addr); + enable_lvds(dev->lcdif_base_addr); + + imx_iomux_v3_setup_multiple_pads(lvds_ctrl_pads, + ARRAY_SIZE(lvds_ctrl_pads)); + + /* Set Brightness to high */ + gpio_direction_output(IMX_GPIO_NR(6, 3) , 1); +} + +void do_enable_parallel_lcd(struct lcd_panel_info_t const *dev) +{ + enable_lcdif_clock(dev->lcdif_base_addr); + + imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads)); + + /* Power up the LCD */ + gpio_direction_output(IMX_GPIO_NR(3, 27) , 1); +} + +static struct lcd_panel_info_t const displays[] = {{ + .lcdif_base_addr = LCDIF2_BASE_ADDR, + .depth = 18, + .enable = do_enable_lvds, + .mode = { + .name = "Hannstar-XGA", + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = 0, + .vmode = FB_VMODE_NONINTERLACED +} }, { + .lcdif_base_addr = LCDIF1_BASE_ADDR, + .depth = 18, + .enable = do_enable_parallel_lcd, + .mode = { + .name = "Boundary-LCD", + .xres = 800, + .yres = 480, + .pixclock = 29850, + .left_margin = 89, + .right_margin = 164, + .upper_margin = 23, + .lower_margin = 10, + .hsync_len = 10, + .vsync_len = 10, + .sync = 0, + .vmode = FB_VMODE_NONINTERLACED +} } }; + +int board_video_skip(void) +{ + int i; + int ret; + char const *panel = getenv("panel"); + if (!panel) { + panel = displays[0].mode.name; + printf("No panel detected: default to %s\n", panel); + i = 0; + } else { + for (i = 0; i < ARRAY_SIZE(displays); i++) { + if (!strcmp(panel, displays[i].mode.name)) + break; + } + } + if (i < ARRAY_SIZE(displays)) { + ret = mxs_lcd_panel_setup(displays[i].mode, displays[i].depth, + displays[i].lcdif_base_addr); + if (!ret) { + if (displays[i].enable) + displays[i].enable(displays+i); + printf("Display: %s (%ux%u)\n", + displays[i].mode.name, + displays[i].mode.xres, + displays[i].mode.yres); + } else + printf("LCD %s cannot be configured: %d\n", + displays[i].mode.name, ret); + } else { + printf("unsupported panel %s\n", panel); + return -EINVAL; + } + + return 0; +} +#endif + +#ifdef CONFIG_FEC_MXC +int board_eth_init(bd_t *bis) +{ + int ret; + + setup_iomux_fec(CONFIG_FEC_ENET_DEV); + + ret = fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV, + CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE); + if (ret) + printf("FEC%d MXC: %s:failed\n", CONFIG_FEC_ENET_DEV, __func__); + + return 0; +} + +static int setup_fec(int fec_id) +{ + struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs + = (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR; + int ret; + + if (0 == fec_id) + /* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/ + clrsetbits_le32(&iomuxc_gpr_regs->gpr[1], IOMUX_GPR1_FEC1_MASK, 0); + else + /* Use 125M anatop REF_CLK1 for ENET2, clear gpr1[14], gpr1[18]*/ + clrsetbits_le32(&iomuxc_gpr_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0); + + ret = enable_fec_anatop_clock(fec_id, ENET_125MHz); + if (ret) + return ret; + + enable_enet_clock(); + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + /* Enable 1.8V(SEL_1P5_1P8_POS_REG) on Phy control debug reg 0 */ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); + + /* rgmii tx clock delay enable */ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} +#endif + +#ifdef CONFIG_PFUZE100_PMIC_I2C +#define PFUZE100_DEVICEID 0x0 +#define PFUZE100_REVID 0x3 +#define PFUZE100_FABID 0x4 + +#define PFUZE100_SW1ABVOL 0x20 +#define PFUZE100_SW1ABSTBY 0x21 +#define PFUZE100_SW1ABCONF 0x24 +#define PFUZE100_SW1CVOL 0x2e +#define PFUZE100_SW1CSTBY 0x2f +#define PFUZE100_SW1CCONF 0x32 +#define PFUZE100_SW1ABC_SETP(x) ((x - 3000) / 250) +#define PFUZE100_VGEN5CTL 0x70 + +/* set all switches APS in normal and PFM mode in standby */ +static int setup_pmic_mode(int chip) +{ + unsigned char offset, i, switch_num, value; + + if (!chip) { + /* pfuze100 */ + switch_num = 6; + offset = 0x31; + } else { + /* pfuze200 */ + switch_num = 4; + offset = 0x38; + } + + value = 0xc; + if (i2c_write(0x8, 0x23, 1, &value, 1)) { + printf("Set SW1AB mode error!\n"); + return -1; + } + + for (i = 0; i < switch_num - 1; i++) { + if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) { + printf("Set switch%x mode error!\n", offset); + return -1; + } + } + + return 0; +} + +static int setup_pmic_voltages(void) +{ + unsigned char value, rev_id = 0; + + i2c_set_bus_num(CONFIG_PMIC_I2C_BUS); + + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_PMIC_I2C_SLAVE); + if (!i2c_probe(CONFIG_PMIC_I2C_SLAVE)) { + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_DEVICEID, 1, &value, 1)) { + printf("Read device ID error!\n"); + return -1; + } + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_REVID, 1, &rev_id, 1)) { + printf("Read Rev ID error!\n"); + return -1; + } + printf("Found PFUZE100! deviceid 0x%x, revid 0x%x\n", value, rev_id); + + if (setup_pmic_mode(value & 0xf)) { + printf("setup pmic mode error!\n"); + return -1; + } + /* set SW1AB standby volatage 0.975V */ + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABSTBY, 1, &value, 1)) { + printf("Read SW1ABSTBY error!\n"); + return -1; + } + value &= ~0x3f; + value |= PFUZE100_SW1ABC_SETP(9750); + if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABSTBY, 1, &value, 1)) { + printf("Set SW1ABSTBY error!\n"); + return -1; + } + + /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABCONF, 1, &value, 1)) { + printf("Read SW1ABCONFIG error!\n"); + return -1; + } + value &= ~0xc0; + value |= 0x40; + if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABCONF, 1, &value, 1)) { + printf("Set SW1ABCONFIG error!\n"); + return -1; + } + + /* set SW1C standby volatage 0.975V */ + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CSTBY, 1, &value, 1)) { + printf("Read SW1CSTBY error!\n"); + return -1; + } + value &= ~0x3f; + value |= PFUZE100_SW1ABC_SETP(9750); + if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CSTBY, 1, &value, 1)) { + printf("Set SW1CSTBY error!\n"); + return -1; + } + + /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */ + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CCONF, 1, &value, 1)) { + printf("Read SW1CCONFIG error!\n"); + return -1; + } + value &= ~0xc0; + value |= 0x40; + if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CCONF, 1, &value, 1)) { + printf("Set SW1CCONFIG error!\n"); + return -1; + } + + /* Enable power of VGEN5 3V3, needed for SD3 */ + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_VGEN5CTL, 1, &value, 1)) { + printf("Read VGEN5CTL error!\n"); + return -1; + } + value &= ~0x1F; + value |= 0x1F; + if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_VGEN5CTL, 1, &value, 1)) { + printf("Set VGEN5CTL error!\n"); + return -1; + } + } + + return 0; +} + +#ifdef CONFIG_LDO_BYPASS_CHECK +void ldo_mode_set(int ldo_bypass) +{ + unsigned char value; + /* switch to ldo_bypass mode */ + if (ldo_bypass) { + /* decrease VDDARM to 1.15V */ + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABVOL, 1, &value, 1)) { + printf("Read SW1AB error!\n"); + return; + } + value &= ~0x3f; + value |= PFUZE100_SW1ABC_SETP(11500); + if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABVOL, 1, &value, 1)) { + printf("Set SW1AB error!\n"); + return; + } + /* increase VDDSOC to 1.15V */ + if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CVOL, 1, &value, 1)) { + printf("Read SW1C error!\n"); + return; + } + value &= ~0x3f; + value |= PFUZE100_SW1ABC_SETP(11500); + if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CVOL, 1, &value, 1)) { + printf("Set SW1C error!\n"); + return; + } + + set_anatop_bypass(1); + printf("switch to ldo_bypass mode!\n"); + } + +} +#endif +#endif + +#ifdef CONFIG_MXC_RDC +static rdc_peri_cfg_t const shared_resources[] = { + (RDC_PER_GPIO1 | RDC_DOMAIN(0) | RDC_DOMAIN(1)), +}; +#endif + +int board_early_init_f(void) +{ +#ifdef CONFIG_MXC_RDC + imx_rdc_setup_peripherals(shared_resources, ARRAY_SIZE(shared_resources)); +#endif + +#ifdef CONFIG_SYS_AUXCORE_FASTUP + arch_auxiliary_core_up(0, CONFIG_SYS_AUXCORE_BOOTDATA); +#endif + + setup_iomux_uart(); + return 0; +} + +int board_init(void) +{ + /* Address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + +#ifdef CONFIG_SYS_I2C_MXC + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); +#endif + +#ifdef CONFIG_FEC_MXC + setup_fec(CONFIG_FEC_ENET_DEV); +#endif + +#ifdef CONFIG_SYS_USE_NAND + setup_gpmi_nand(); +#endif + +#ifdef CONFIG_QSPI + board_qspi_init(); +#endif + + return 0; +} + +#ifdef CONFIG_CMD_BMODE +static const struct boot_mode board_boot_modes[] = { + {"sda", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, + {"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, + {"qspi1", MAKE_CFGVAL(0x18, 0x00, 0x00, 0x00)}, + {"nand", MAKE_CFGVAL(0x18, 0x00, 0x00, 0x00)}, + {NULL, 0}, +}; +#endif + +int board_late_init(void) +{ +#ifdef CONFIG_CMD_BMODE + add_board_boot_modes(board_boot_modes); +#endif + +#ifdef CONFIG_PFUZE100_PMIC_I2C + int ret = 0; + + ret = setup_pmic_voltages(); + if (ret) + return -1; +#endif + +#ifdef CONFIG_ENV_IS_IN_MMC + board_late_mmc_init(); +#endif + + return 0; +} + +u32 get_board_rev(void) +{ + return get_cpu_rev(); +} + +int checkboard(void) +{ + puts("Board: MX6SX SABRE AUTO\n"); + + return 0; +} + +#ifdef CONFIG_USB_EHCI_MX6 +iomux_v3_cfg_t const usb_otg1_pads[] = { + MX6SX_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL) +}; + +iomux_v3_cfg_t const usb_host2_pads[] = { + MX6SX_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +int board_ehci_hcd_init(int port) +{ + switch (port) { + case 0: + imx_iomux_v3_setup_multiple_pads(usb_otg1_pads, + ARRAY_SIZE(usb_otg1_pads)); + break; + case 1: + imx_iomux_v3_setup_multiple_pads(usb_host2_pads, + ARRAY_SIZE(usb_host2_pads)); + break; + default: + printf("MXC USB port %d not yet supported\n", port); + return 1; + } + return 0; +} +#endif diff --git a/board/freescale/mx6sxsabreauto/plugin.S b/board/freescale/mx6sxsabreauto/plugin.S new file mode 100644 index 0000000..169a852 --- /dev/null +++ b/board/freescale/mx6sxsabreauto/plugin.S @@ -0,0 +1,143 @@ +/* + * Copyright (C) 2013-2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include + +/* DDR script */ +.macro imx6sx_sabreauto_ddr_setting + ldr r0, =IOMUXC_BASE_ADDR + ldr r1, =0x000c0000 + str r1, [r0, #0x618] + ldr r1, =0x00000000 + str r1, [r0, #0x5fc] + ldr r1, =0x00000030 + str r1, [r0, #0x32c] + + ldr r1, =0x00000030 + str r1, [r0, #0x300] + str r1, [r0, #0x2fc] + str r1, [r0, #0x5f4] + str r1, [r0, #0x340] + + ldr r1, =0x00000000 + str r1, [r0, #0x320] + ldr r1, =0x00000030 + str r1, [r0, #0x310] + str r1, [r0, #0x314] + str r1, [r0, #0x614] + + ldr r1, =0x00020000 + str r1, [r0, #0x5f8] + ldr r1, =0x00000030 + str r1, [r0, #0x330] + str r1, [r0, #0x334] + str r1, [r0, #0x338] + str r1, [r0, #0x33c] + ldr r1, =0x00020000 + str r1, [r0, #0x608] + ldr r1, =0x00000030 + str r1, [r0, #0x60c] + str r1, [r0, #0x610] + str r1, [r0, #0x61c] + str r1, [r0, #0x620] + str r1, [r0, #0x2ec] + str r1, [r0, #0x2f0] + str r1, [r0, #0x2f4] + str r1, [r0, #0x2f8] + + ldr r0, =MMDC_P0_BASE_ADDR + ldr r2, =0xa1390003 + str r2, [r0, #0x800] + ldr r2, =0x002C003D + str r2, [r0, #0x80c] + ldr r2, =0x00110046 + str r2, [r0, #0x810] + ldr r2, =0x4160016C + str r2, [r0, #0x83c] + ldr r2, =0x013C016C + str r2, [r0, #0x840] + ldr r2, =0x46424446 + str r2, [r0, #0x848] + ldr r2, =0x3A3C3C3A + str r2, [r0, #0x850] + ldr r2, =0x2492244A + str r2, [r0, #0x8c0] + + ldr r2, =0x33333333 + str r2, [r0, #0x81c] + str r2, [r0, #0x820] + str r2, [r0, #0x824] + str r2, [r0, #0x828] + + ldr r2, =0x00000800 + str r2, [r0, #0x8b8] + ldr r2, =0x0002002d + str r2, [r0, #0x004] + ldr r2, =0x00333030 + str r2, [r0, #0x008] + ldr r2, =0x676b52f3 + str r2, [r0, #0x00c] + ldr r2, =0xb66d8b63 + str r2, [r0, #0x010] + ldr r2, =0x01ff00db + str r2, [r0, #0x014] + ldr r2, =0x00011740 + str r2, [r0, #0x018] + ldr r2, =0x00008000 + str r2, [r0, #0x01c] + ldr r2, =0x000026d2 + str r2, [r0, #0x02c] + ldr r2, =0x006b1023 + str r2, [r0, #0x030] + ldr r2, =0x0000007f + str r2, [r0, #0x040] + ldr r2, =0x85190000 + str r2, [r0, #0x000] + ldr r2, =0x04008032 + str r2, [r0, #0x01c] + ldr r2, =0x00008033 + str r2, [r0, #0x01c] + ldr r2, =0x00068031 + str r2, [r0, #0x01c] + ldr r2, =0x05208030 + str r2, [r0, #0x01c] + ldr r2, =0x04008040 + str r2, [r0, #0x01c] + ldr r2, =0x00000800 + str r2, [r0, #0x020] + ldr r2, =0x00022227 + str r2, [r0, #0x818] + ldr r2, =0x0002556d + str r2, [r0, #0x004] + ldr r2, =0x00011006 + str r2, [r0, #0x404] + ldr r2, =0x00000000 + str r2, [r0, #0x01c] + +.endm + +.macro imx6_clock_gating + ldr r0, =CCM_BASE_ADDR + ldr r1, =0xffffffff + str r1, [r0, #0x068] + str r1, [r0, #0x06c] + str r1, [r0, #0x070] + str r1, [r0, #0x074] + str r1, [r0, #0x078] + str r1, [r0, #0x07c] + str r1, [r0, #0x080] + str r1, [r0, #0x084] +.endm + +.macro imx6_qos_setting +.endm + +.macro imx6_ddr_setting + imx6sx_sabreauto_ddr_setting +.endm + +/* include the common plugin code here */ +#include diff --git a/boards.cfg b/boards.cfg index cf86801..59a6dc9 100644 --- a/boards.cfg +++ b/boards.cfg @@ -368,6 +368,9 @@ Active arm armv7 mx6 freescale mx6sxsabresd Active arm armv7 mx6 freescale mx6sxsabresd mx6sxsabresd_m4fastup mx6sxsabresd:IMX_CONFIG=board/freescale/mx6sxsabresd/imximage.cfg,MX6SX,SYS_BOOT_QSPI,SYS_AUXCORE_FASTUP Fabio Estevam Active arm armv7 mx6 freescale mx6sxsabresd mx6sxsabresd_emmc mx6sxsabresd:IMX_CONFIG=board/freescale/mx6sxsabresd/imximage.cfg,MX6SX,MX6SXSABRESD_EMMC_REWORK Fabio Estevam Active arm armv7 mx6 freescale mx6sxsabresd mx6sxsabresdandroid mx6sxsabresd:IMX_CONFIG=board/freescale/mx6sxsabresd/imximage.cfg,MX6SX,ANDROID_SUPPORT Fabio Estevam +Active arm armv7 mx6 freescale mx6sxsabreauto mx6sxsabreauto mx6sxsabreauto:IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg,MX6SX Fabio Estevam +Active arm armv7 mx6 freescale mx6sxsabreauto mx6sxsabreauto_qspi1 mx6sxsabreauto:IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg,MX6SX,SYS_BOOT_QSPI Fabio Estevam +Active arm armv7 mx6 freescale mx6sxsabreauto mx6sxsabreauto_nand mx6sxsabreauto:IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg,MX6SX,SYS_BOOT_NAND Fabio Estevam Active arm armv7 mx6 gateworks gw_ventana gwventanadl gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6DL,DDR_MB=512 Tim Harvey Active arm armv7 mx6 gateworks gw_ventana gwventanadl1g gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6DL,DDR_MB=1024 Tim Harvey Active arm armv7 mx6 gateworks gw_ventana gwventanaq gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6Q,DDR_MB=512 Tim Harvey diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h new file mode 100644 index 0000000..34e915a --- /dev/null +++ b/include/configs/mx6sxsabreauto.h @@ -0,0 +1,386 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * Configuration settings for the Freescale i.MX6SX SABREAUTO board. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __MX6SX_SABREAUTO_CONFIG_H +#define __MX6SX_SABREAUTO_CONFIG_H + +#include +#include +#include "mx6_common.h" +#include + +#define CONFIG_MX6 +#define CONFIG_ROM_UNIFIED_SECTIONS +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_DBG_MONITOR +/* uncomment for PLUGIN mode support */ +/* #define CONFIG_USE_PLUGIN */ + +/* uncomment for SECURE mode support */ +/* #define CONFIG_SECURE_BOOT */ + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART1_BASE + +#define CONFIG_CMD_FUSE +#ifdef CONFIG_CMD_FUSE +#define CONFIG_MXC_OCOTP +#endif + +/* MMC Configs */ +#define CONFIG_FSL_ESDHC +#define CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define CONFIG_SYS_FSL_USDHC_NUM 2 + +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */ + +#define CONFIG_BAUDRATE 115200 + +#undef CONFIG_BOOTM_NETBSD +#undef CONFIG_BOOTM_PLAN9 +#undef CONFIG_BOOTM_RTEMS + +#undef CONFIG_CMD_EXPORTENV +#undef CONFIG_CMD_IMPORTENV + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define CONFIG_FEC_ENET_DEV 1 /* Use onboard ethernet as default */ + +#if (CONFIG_FEC_ENET_DEV == 0) +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_MXC_PHYADDR 0x0 +#elif (CONFIG_FEC_ENET_DEV == 1) +#define IMX_FEC_BASE ENET2_BASE_ADDR +#define CONFIG_FEC_MXC_PHYADDR 0x0 +#endif +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" + +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS +#define CONFIG_FEC_DMA_MINALIGN 64 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 + +/* I2C configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 + +/* PMIC */ +#define CONFIG_PFUZE100_PMIC_I2C +#ifdef CONFIG_PFUZE100_PMIC_I2C +#define CONFIG_PMIC_I2C_BUS 1 +#define CONFIG_PMIC_I2C_SLAVE 0x8 +#endif + +/* VIDEO */ +#define CONFIG_VIDEO + +/* Command definition */ +#include + +#undef CONFIG_CMD_IMLS + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_LOADADDR 0x80800000 +#define CONFIG_SYS_TEXT_BASE 0x87800000 + +#define CONFIG_SYS_AUXCORE_BOOTDATA 0x68000000 /* Set to QSPI1 B flash at default */ +#ifndef CONFIG_SYS_AUXCORE_FASTUP +#define CONFIG_CMD_BOOTAUX /* Boot M4 by command, disable this when M4 fast up */ +#define CONFIG_CMD_SETEXPR +#endif + +#ifdef CONFIG_CMD_BOOTAUX +#define UPDATE_M4_ENV \ + "m4image=m4_qspi.bin\0" \ + "loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \ + "update_m4_from_sd=" \ + "if sf probe 1:0; then " \ + "if run loadm4image; then " \ + "setexpr fw_sz ${filesize} + 0xffff; " \ + "setexpr fw_sz ${fw_sz} / 0x10000; " \ + "setexpr fw_sz ${fw_sz} * 0x10000; " \ + "sf erase 0x0 ${fw_sz}; " \ + "sf write ${loadaddr} 0x0 ${filesize}; " \ + "fi; " \ + "fi\0" \ + "m4boot=sf probe 1:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0" +#else +#define UPDATE_M4_ENV "" +#endif + +#ifdef CONFIG_VIDEO +#define CONFIG_VIDEO_MODE \ + "panel=Hannstar-XGA\0" +#else +#define CONFIG_VIDEO_MODE "" +#endif + +#define CONFIG_MFG_ENV_SETTINGS \ + "mfgtool_args=setenv bootargs console=${console},${baudrate} " \ + "rdinit=/linuxrc " \ + "g_mass_storage.stall=0 g_mass_storage.removable=1 " \ + "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\ + "g_mass_storage.iSerialNumber=\"\" "\ + "\0" \ + "initrd_addr=0x83800000\0" \ + "initrd_high=0xffffffff\0" \ + "bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_MFG_ENV_SETTINGS \ + UPDATE_M4_ENV \ + CONFIG_VIDEO_MODE \ + "script=boot.scr\0" \ + "image=zImage\0" \ + "console=ttymxc0\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=imx6sx-sabreauto.dtb\0" \ + "fdt_addr=0x83000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \ + "mmcpart=1\0" \ + "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \ + "mmcautodetect=yes\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${image}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev};" \ + "if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 1024 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 256 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_CMD_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000) + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_EDITING +#define CONFIG_STACKSIZE SZ_128K + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define PHYS_SDRAM_SIZE SZ_1G + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_ENV_SIZE SZ_8K + +#ifdef CONFIG_SYS_AUXCORE_FASTUP +/*#define CONFIG_MXC_RDC*/ /* Disable the RDC temporarily, will enable it in future */ +#define CONFIG_ENV_IS_IN_MMC /* Must disable QSPI driver, because M4 run on QSPI */ +#elif defined CONFIG_SYS_BOOT_QSPI +#define CONFIG_SYS_USE_QSPI +#define CONFIG_ENV_IS_IN_SPI_FLASH +#elif defined CONFIG_SYS_BOOT_NAND +#define CONFIG_SYS_USE_NAND +#define CONFIG_ENV_IS_IN_NAND +#else +#define CONFIG_SYS_USE_QSPI /* Enable the QSPI flash at default */ +#define CONFIG_ENV_IS_IN_MMC +#endif + +#ifdef CONFIG_SYS_USE_QSPI +#define CONFIG_QSPI /* enable the QUADSPI driver */ +#define CONFIG_QSPI_BASE QSPI1_BASE_ADDR +#define CONFIG_QSPI_MEMMAP_BASE QSPI1_ARB_BASE_ADDR + +#define CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS 0 +#define CONFIG_SF_DEFAULT_SPEED 40000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#endif + +#ifdef CONFIG_SYS_USE_NAND +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NAND_TRIMFFS + +/* NAND stuff */ +#define CONFIG_NAND_MXS +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* DMA stuff, needed for GPMI/MXS NAND support */ +#define CONFIG_APBH_DMA +#define CONFIG_APBH_DMA_BURST +#define CONFIG_APBH_DMA_BURST8 +#endif + +#define CONFIG_SYS_MMC_ENV_DEV 0 /*USDHC3*/ +#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */ +#define CONFIG_MMCROOT "/dev/mmcblk2p2" /* USDHC3 */ + +#if defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_ENV_OFFSET (8 * SZ_64K) +#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH) +#define CONFIG_ENV_OFFSET (768 * 1024) +#define CONFIG_ENV_SECT_SIZE (64 * 1024) +#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS +#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS +#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#elif defined(CONFIG_ENV_IS_IN_NAND) +#undef CONFIG_ENV_SIZE +#define CONFIG_ENV_OFFSET (8 << 20) +#define CONFIG_ENV_SECT_SIZE (128 << 10) +#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE +#endif + +#define CONFIG_OF_LIBFDT +#define CONFIG_CMD_BOOTZ + +#define CONFIG_CMD_BMODE + +#ifndef CONFIG_SYS_DCACHE_OFF +#define CONFIG_CMD_CACHE +#endif + +#ifdef CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_MXS +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SPLASH_SCREEN_ALIGN +#define CONFIG_CMD_BMP +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_VIDEO_BMP_LOGO +#endif + +#define CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MX6 +#define CONFIG_USB_STORAGE +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 + +#endif /* __CONFIG_H */ -- cgit v1.1