From 87db58dca47f93f9fb3b4ed0196dd7a3f5df1cb9 Mon Sep 17 00:00:00 2001 From: Anatolij Gustschin Date: Wed, 21 Apr 2010 13:52:38 +0200 Subject: tx25: fix crash while booting Linux Currently booting Linux on TX25 board doesn't work since there is no correct mach-id and boot parameters setup for tx25 board. Fix it now. Signed-off-by: Anatolij Gustschin Cc: John Rigby Cc: Stefano Babic --- board/karo/tx25/tx25.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/board/karo/tx25/tx25.c b/board/karo/tx25/tx25.c index 4d6a96d..2608698 100644 --- a/board/karo/tx25/tx25.c +++ b/board/karo/tx25/tx25.c @@ -145,6 +145,9 @@ int board_init() mx25_uart_init_pins(); #endif + /* board id for linux */ + gd->bd->bi_arch_number = MACH_TYPE_TX25; + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; return 0; } -- cgit v1.1 From 68c07a0c215a64826ed13c2f9b00a6d3b298822e Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Sun, 18 Apr 2010 20:01:01 +0200 Subject: MX51evk: Removed warnings Changes reflect modifications in the fsl_esdhc driver (the clk_enable field war removed in the configuration structure). Signed-off-by: Stefano Babic --- board/freescale/mx51evk/mx51evk.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index f0b7abc..3d89be3 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -39,8 +39,8 @@ struct io_board_ctrl *mx51_io_board; #ifdef CONFIG_FSL_ESDHC struct fsl_esdhc_cfg esdhc_cfg[2] = { - {MMC_SDHC1_BASE_ADDR, 1, 1}, - {MMC_SDHC2_BASE_ADDR, 1, 1}, + {MMC_SDHC1_BASE_ADDR, 1}, + {MMC_SDHC2_BASE_ADDR, 1}, }; #endif -- cgit v1.1 From 60381d687885c0e2100657ca73e97e38c4604f5e Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Fri, 23 Apr 2010 06:32:01 -0700 Subject: MX51: Fix MX51 CPU detect message Fix MX51 CPU detect message. Original string was: CPU: Freescale i.MX51 family 3.0V at 800 MHz which can be misinterpreted as 3.0 Volts instead of the silicon revision. ,change it to: CPU: Freescale i.MX51 family rev3.0 at 800 MHz Signed-off-by: Fabio Estevam --- arch/arm/cpu/arm_cortexa8/mx51/soc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/cpu/arm_cortexa8/mx51/soc.c b/arch/arm/cpu/arm_cortexa8/mx51/soc.c index 2a139b2..f22ebe9 100644 --- a/arch/arm/cpu/arm_cortexa8/mx51/soc.c +++ b/arch/arm/cpu/arm_cortexa8/mx51/soc.c @@ -67,7 +67,7 @@ int print_cpuinfo(void) u32 cpurev; cpurev = get_cpu_rev(); - printf("CPU: Freescale i.MX51 family %d.%dV at %d MHz\n", + printf("CPU: Freescale i.MX51 family rev%d.%d at %d MHz\n", (cpurev & 0xF0) >> 4, (cpurev & 0x0F) >> 4, mxc_get_clock(MXC_ARM_CLK) / 1000000); -- cgit v1.1 From ba6adeb48e71f7f1b791b6e98999a5680d919b26 Mon Sep 17 00:00:00 2001 From: Magnus Lilja Date: Fri, 23 Apr 2010 20:30:49 +0200 Subject: i.MX31: Activate NAND support for i.MX31 Litekit board. Signed-off-by: Magnus Lilja --- include/configs/imx31_litekit.h | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h index 6131008..d58ca8a 100644 --- a/include/configs/imx31_litekit.h +++ b/include/configs/imx31_litekit.h @@ -89,6 +89,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_SPI #define CONFIG_CMD_DATE +#define CONFIG_CMD_NAND #define CONFIG_BOOTDELAY 3 @@ -174,4 +175,13 @@ #undef CONFIG_CMD_MTDPARTS #define CONFIG_JFFS2_DEV "nor0" +/* + * NAND flash + */ +#define CONFIG_NAND_MXC +#define CONFIG_MXC_NAND_REGS_BASE NFC_BASE_ADDR +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR +#define CONFIG_MXC_NAND_HWECC + #endif /* __CONFIG_H */ -- cgit v1.1 From 28bb6d34d3f431b7b00444e2f829b2c04f5daf4d Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Sun, 4 Apr 2010 23:08:03 +0200 Subject: MX: Added Freescale Power Management Driver The patch add supports for the Freescale's Power Management Controller (known as Atlas) used together with i.MX31/51 processors. It was tested with a MC13783 (MX31) and MC13892 (MX51). Signed-off-by: Stefano Babic --- drivers/misc/Makefile | 1 + drivers/misc/fsl_pmic.c | 200 ++++++++++++++++++++++++++++++++++++++++++++++++ include/fsl_pmic.h | 128 +++++++++++++++++++++++++++++++ 3 files changed, 329 insertions(+) create mode 100644 drivers/misc/fsl_pmic.c create mode 100644 include/fsl_pmic.h diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index f6df60f..96aa331 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -31,6 +31,7 @@ COBJS-$(CONFIG_FSL_LAW) += fsl_law.o COBJS-$(CONFIG_NS87308) += ns87308.o COBJS-$(CONFIG_STATUS_LED) += status_led.o COBJS-$(CONFIG_TWL4030_LED) += twl4030_led.o +COBJS-$(CONFIG_FSL_PMIC) += fsl_pmic.o COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) diff --git a/drivers/misc/fsl_pmic.c b/drivers/misc/fsl_pmic.c new file mode 100644 index 0000000..87f0aed --- /dev/null +++ b/drivers/misc/fsl_pmic.c @@ -0,0 +1,200 @@ +/* + * (C) Copyright 2008-2009 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +static struct spi_slave *slave; + +struct spi_slave *pmic_spi_probe(void) +{ + return spi_setup_slave(CONFIG_FSL_PMIC_BUS, + CONFIG_FSL_PMIC_CS, + CONFIG_FSL_PMIC_CLK, + CONFIG_FSL_PMIC_MODE); +} + +void pmic_spi_free(struct spi_slave *slave) +{ + if (slave) + spi_free_slave(slave); +} + +u32 pmic_reg(u32 reg, u32 val, u32 write) +{ + u32 pmic_tx, pmic_rx; + + if (!slave) { + slave = pmic_spi_probe(); + + if (!slave) + return -1; + } + + if (reg > 63 || write > 1) { + printf(" = %d is invalid. Should be less then 63\n", + reg); + return -1; + } + + if (spi_claim_bus(slave)) + return -1; + + pmic_tx = (write << 31) | (reg << 25) | (val & 0x00FFFFFF); + + if (spi_xfer(slave, 4 << 3, &pmic_tx, &pmic_rx, + SPI_XFER_BEGIN | SPI_XFER_END)) { + spi_release_bus(slave); + return -1; + } + + if (write) { + pmic_tx &= ~(1 << 31); + if (spi_xfer(slave, 4 << 3, &pmic_tx, &pmic_rx, + SPI_XFER_BEGIN | SPI_XFER_END)) { + spi_release_bus(slave); + return -1; + } + } + + spi_release_bus(slave); + return pmic_rx; +} + +void pmic_reg_write(u32 reg, u32 value) +{ + pmic_reg(reg, value, 1); +} + +u32 pmic_reg_read(u32 reg) +{ + return pmic_reg(reg, 0, 0); +} + +void pmic_show_pmic_info(void) +{ + u32 rev_id; + + rev_id = pmic_reg_read(REG_IDENTIFICATION); + printf("PMIC ID: 0x%08x [Rev: ", rev_id); + switch (rev_id & 0x1F) { + case 0x1: + puts("1.0"); + break; + case 0x9: + puts("1.1"); + break; + case 0xA: + puts("1.2"); + break; + case 0x10: + puts("2.0"); + break; + case 0x11: + puts("2.1"); + break; + case 0x18: + puts("3.0"); + break; + case 0x19: + puts("3.1"); + break; + case 0x1A: + puts("3.2"); + break; + case 0x2: + puts("3.2A"); + break; + case 0x1B: + puts("3.3"); + break; + case 0x1D: + puts("3.5"); + break; + default: + puts("unknown"); + break; + } + puts("]\n"); +} + +static void pmic_dump(int numregs) +{ + u32 val; + int i; + + pmic_show_pmic_info(); + for (i = 0; i < numregs; i++) { + val = pmic_reg_read(i); + if (!(i % 8)) + printf ("\n0x%02x: ", i); + printf("%08x ", val); + } + puts("\n"); +} + +int do_pmic(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + char *cmd; + int nregs; + u32 val; + + /* at least two arguments please */ + if (argc < 2) { + cmd_usage(cmdtp); + return 1; + } + + cmd = argv[1]; + if (strcmp(cmd, "dump") == 0) { + if (argc < 3) { + cmd_usage(cmdtp); + return 1; + } + nregs = simple_strtoul(argv[2], NULL, 16); + pmic_dump(nregs); + return 0; + } + if (strcmp(cmd, "write") == 0) { + if (argc < 4) { + cmd_usage(cmdtp); + return 1; + } + nregs = simple_strtoul(argv[2], NULL, 16); + val = simple_strtoul(argv[3], NULL, 16); + pmic_reg_write(nregs, val); + return 0; + } + /* No subcommand found */ + return 1; +} + +U_BOOT_CMD( + pmic, CONFIG_SYS_MAXARGS, 1, do_pmic, + "Freescale PMIC (Atlas)", + "dump [numregs] dump registers\n" + "pmic write - write register" +); diff --git a/include/fsl_pmic.h b/include/fsl_pmic.h new file mode 100644 index 0000000..e3abde6 --- /dev/null +++ b/include/fsl_pmic.h @@ -0,0 +1,128 @@ +/* + * (C) Copyright 2010 + * Stefano Babic, DENX Software Engineering, sbabic@denx.de. + * + * (C) Copyright 2009 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __FSL_PMIC_H__ +#define __FSL_PMIC_H__ + +/* + * The registers of different PMIC has the same meaning + * but the bit positions of the fields can differ or + * some fields has a meaning only on some devices. + * You have to check with the internal SPI bitmap + * (see Freescale Documentation) to set the registers + * for the device you are using + */ +enum { + REG_INT_STATUS0 = 0, + REG_INT_MASK0, + REG_INT_SENSE0, + REG_INT_STATUS1, + REG_INT_MASK1, + REG_INT_SENSE1, + REG_PU_MODE_S, + REG_IDENTIFICATION, + REG_UNUSED0, + REG_ACC0, + REG_ACC1, /*10 */ + REG_UNUSED1, + REG_UNUSED2, + REG_POWER_CTL0, + REG_POWER_CTL1, + REG_POWER_CTL2, + REG_REGEN_ASSIGN, + REG_UNUSED3, + REG_MEM_A, + REG_MEM_B, + REG_RTC_TIME, /*20 */ + REG_RTC_ALARM, + REG_RTC_DAY, + REG_RTC_DAY_ALARM, + REG_SW_0, + REG_SW_1, + REG_SW_2, + REG_SW_3, + REG_SW_4, + REG_SW_5, + REG_SETTING_0, /*30 */ + REG_SETTING_1, + REG_MODE_0, + REG_MODE_1, + REG_POWER_MISC, + REG_UNUSED4, + REG_UNUSED5, + REG_UNUSED6, + REG_UNUSED7, + REG_UNUSED8, + REG_UNUSED9, /*40 */ + REG_UNUSED10, + REG_UNUSED11, + REG_ADC0, + REG_ADC1, + REG_ADC2, + REG_ADC3, + REG_ADC4, + REG_CHARGE, + REG_USB0, + REG_USB1, /*50 */ + REG_LED_CTL0, + REG_LED_CTL1, + REG_LED_CTL2, + REG_LED_CTL3, + REG_UNUSED12, + REG_UNUSED13, + REG_TRIM0, + REG_TRIM1, + REG_TEST0, + REG_TEST1, /*60 */ + REG_TEST2, + REG_TEST3, + REG_TEST4, +}; + +/* REG_POWER_MISC */ +#define GPO1EN (1 << 6) +#define GPO1STBY (1 << 7) +#define GPO2EN (1 << 8) +#define GPO2STBY (1 << 9) +#define GPO3EN (1 << 10) +#define GPO3STBY (1 << 11) +#define GPO4EN (1 << 12) +#define GPO4STBY (1 << 13) +#define PWGT1SPIEN (1 << 15) +#define PWGT2SPIEN (1 << 16) +#define PWUP (1 << 21) + +/* Power Control 0 */ +#define COINCHEN (1 << 23) +#define BATTDETEN (1 << 19) + +/* Interrupt status 1 */ +#define RTCRSTI (1 << 7) + +void pmic_show_pmic_info(void); +void pmic_reg_write(u32 reg, u32 value); +u32 pmic_reg_read(u32 reg); + +#endif -- cgit v1.1 From dfe5e14fa263eb8f1a9f087f0284788e7559821d Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Fri, 16 Apr 2010 17:11:19 +0200 Subject: MX: RTC13783 uses general function to access PMIC The RTC is part of the Freescale's PMIC controller. Use general function to access to PMIC internal registers. Signed-off-by: Stefano Babic Tested-by: Magnus Lilja --- drivers/rtc/mc13783-rtc.c | 72 +++++++++-------------------------------- include/configs/imx31_litekit.h | 9 ++++-- include/configs/mx31ads.h | 8 +++-- include/configs/mx31pdk.h | 9 +++--- 4 files changed, 31 insertions(+), 67 deletions(-) diff --git a/drivers/rtc/mc13783-rtc.c b/drivers/rtc/mc13783-rtc.c index 416f50d..4e18f80 100644 --- a/drivers/rtc/mc13783-rtc.c +++ b/drivers/rtc/mc13783-rtc.c @@ -23,53 +23,30 @@ #include #include #include - -static struct spi_slave *slave; +#include int rtc_get(struct rtc_time *rtc) { u32 day1, day2, time; - u32 reg; - int err, tim, i = 0; - - if (!slave) { - /* FIXME: Verify the max SCK rate */ - slave = spi_setup_slave(CONFIG_MC13783_SPI_BUS, - CONFIG_MC13783_SPI_CS, 1000000, - SPI_MODE_2 | SPI_CS_HIGH); - if (!slave) - return -1; - } - - if (spi_claim_bus(slave)) - return -1; + int tim, i = 0; do { - reg = 0x2c000000; - err = spi_xfer(slave, 32, (uchar *)®, (uchar *)&day1, - SPI_XFER_BEGIN | SPI_XFER_END); - - if (err) - return err; - - reg = 0x28000000; - err = spi_xfer(slave, 32, (uchar *)®, (uchar *)&time, - SPI_XFER_BEGIN | SPI_XFER_END); + day1 = pmic_reg_read(REG_RTC_DAY); + if (day1 < 0) + return -1; - if (err) - return err; + time = pmic_reg_read(REG_RTC_TIME); + if (time < 0) + return -1; - reg = 0x2c000000; - err = spi_xfer(slave, 32, (uchar *)®, (uchar *)&day2, - SPI_XFER_BEGIN | SPI_XFER_END); + day2 = pmic_reg_read(REG_RTC_DAY); + if (day2 < 0) + return -1; - if (err) - return err; } while (day1 != day2 && i++ < 3); - spi_release_bus(slave); - tim = day1 * 86400 + time; + to_tm(tim, rtc); rtc->tm_yday = 0; @@ -80,34 +57,15 @@ int rtc_get(struct rtc_time *rtc) int rtc_set(struct rtc_time *rtc) { - u32 time, day, reg; - - if (!slave) { - /* FIXME: Verify the max SCK rate */ - slave = spi_setup_slave(CONFIG_MC13783_SPI_BUS, - CONFIG_MC13783_SPI_CS, 1000000, - SPI_MODE_2 | SPI_CS_HIGH); - if (!slave) - return -1; - } + u32 time, day; time = mktime(rtc->tm_year, rtc->tm_mon, rtc->tm_mday, rtc->tm_hour, rtc->tm_min, rtc->tm_sec); day = time / 86400; time %= 86400; - if (spi_claim_bus(slave)) - return -1; - - reg = 0x2c000000 | day | 0x80000000; - spi_xfer(slave, 32, (uchar *)®, (uchar *)&day, - SPI_XFER_BEGIN | SPI_XFER_END); - - reg = 0x28000000 | time | 0x80000000; - spi_xfer(slave, 32, (uchar *)®, (uchar *)&time, - SPI_XFER_BEGIN | SPI_XFER_END); - - spi_release_bus(slave); + pmic_reg_write(REG_RTC_DAY, day); + pmic_reg_write(REG_RTC_TIME, time); return 0; } diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h index d58ca8a..4904856 100644 --- a/include/configs/imx31_litekit.h +++ b/include/configs/imx31_litekit.h @@ -68,10 +68,13 @@ #define CONFIG_DEFAULT_SPI_BUS 1 #define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_BUS 1 +#define CONFIG_FSL_PMIC_CS 0 +#define CONFIG_FSL_PMIC_CLK 1000000 +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) + #define CONFIG_RTC_MC13783 1 -/* MC13783 connected to CSPI2 and SS0 */ -#define CONFIG_MC13783_SPI_BUS 1 -#define CONFIG_MC13783_SPI_CS 0 /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index ec1c905..dedecd7 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -65,10 +65,12 @@ #define CONFIG_DEFAULT_SPI_BUS 1 #define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_BUS 1 +#define CONFIG_FSL_PMIC_CS 0 +#define CONFIG_FSL_PMIC_CLK 1000000 +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 1 -/* MC13783 connected to CSPI2 and SS0 */ -#define CONFIG_MC13783_SPI_BUS 1 -#define CONFIG_MC13783_SPI_CS 0 /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE diff --git a/include/configs/mx31pdk.h b/include/configs/mx31pdk.h index bee2f45..0414cc3 100644 --- a/include/configs/mx31pdk.h +++ b/include/configs/mx31pdk.h @@ -69,12 +69,13 @@ #define CONFIG_DEFAULT_SPI_BUS 1 #define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_BUS 1 +#define CONFIG_FSL_PMIC_CS 2 +#define CONFIG_FSL_PMIC_CLK 1000000 +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 1 -/* MC13783 connected to CSPI2 and SS2 */ -#define CONFIG_MC13783_SPI_BUS 1 -#define CONFIG_MC13783_SPI_CS 2 - /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_CONS_INDEX 1 -- cgit v1.1 From e98ecd71102de9d97bd82be247ed909260fb671b Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Fri, 16 Apr 2010 17:13:54 +0200 Subject: MX31: Add support for PMIC to the QONG module Add support for the PMIC (MC13783) controller and enables charging of the RTC battery. Signed-off-by: Stefano Babic --- board/davedenx/qong/qong.c | 20 ++++++++++++++++++++ include/configs/qong.h | 14 ++++++++++++++ 2 files changed, 34 insertions(+) diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c index eb9218e..781333b 100644 --- a/board/davedenx/qong/qong.c +++ b/board/davedenx/qong/qong.c @@ -26,6 +26,7 @@ #include #include #include +#include #include "qong_fpga.h" DECLARE_GLOBAL_DATA_PTR; @@ -128,6 +129,13 @@ int board_init (void) mx31_gpio_mux(MUX_RTS1__UART1_RTS_B); mx31_gpio_mux(MUX_CTS1__UART1_CTS_B); + /* setup pins for SPI (pmic) */ + mx31_gpio_mux(MUX_CSPI2_SS0__CSPI2_SS0_B); + mx31_gpio_mux(MUX_CSPI2_MOSI__CSPI2_MOSI); + mx31_gpio_mux(MUX_CSPI2_MISO__CSPI2_MISO); + mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK); + mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B); + /* board id for linux */ gd->bd->bi_arch_number = MACH_TYPE_QONG; gd->bd->bi_boot_params = (0x80000100); /* adress of boot parameters */ @@ -135,6 +143,18 @@ int board_init (void) return 0; } +int board_late_init(void) +{ + u32 val; + + /* Enable RTC battery */ + val = pmic_reg_read(REG_POWER_CTL0); + pmic_reg_write(REG_POWER_CTL0, val | COINCHEN); + pmic_reg_write(REG_INT_STATUS1, RTCRSTI); + + return 0; +} + int checkboard (void) { printf("Board: DAVE/DENX Qong\n"); diff --git a/include/configs/qong.h b/include/configs/qong.h index 1d63b33..eb4669b 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -54,6 +54,17 @@ #define CONFIG_MX31_GPIO +#define CONFIG_MXC_SPI +#define CONFIG_DEFAULT_SPI_BUS 1 +#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_RTC_MC13783 + +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_BUS 1 +#define CONFIG_FSL_PMIC_CS 0 +#define CONFIG_FSL_PMIC_CLK 100000 +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) + /* FPGA */ #define CONFIG_QONG_FPGA 1 #define CONFIG_FPGA_BASE (CS1_BASE) @@ -98,6 +109,9 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_MII #define CONFIG_CMD_NAND +#define CONFIG_CMD_SPI +#define CONFIG_CMD_DATE +#define BOARD_LATE_INIT /* * You can compile in a MAC address and your custom net settings by using -- cgit v1.1 From d205ddcfc5b905eff023d5acac395721d80a92c7 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Sun, 4 Apr 2010 22:43:38 +0200 Subject: SPI: added support for MX51 to mxc_spi This patch add SPI support for the MX51 processor. Signed-off-by: Stefano Babic --- drivers/spi/mxc_spi.c | 231 +++++++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 211 insertions(+), 20 deletions(-) diff --git a/drivers/spi/mxc_spi.c b/drivers/spi/mxc_spi.c index 3a45200..e15a63c 100644 --- a/drivers/spi/mxc_spi.c +++ b/drivers/spi/mxc_spi.c @@ -31,7 +31,7 @@ #error "i.MX27 CSPI not supported due to drastic differences in register definisions" \ "See linux mxc_spi driver from Freescale for details." -#else +#elif defined(CONFIG_MX31) #include @@ -56,6 +56,9 @@ #define MXC_CSPICTRL_CHIPSELECT(x) (((x) & 0x3) << 24) #define MXC_CSPICTRL_BITCOUNT(x) (((x) & 0x1f) << 8) #define MXC_CSPICTRL_DATARATE(x) (((x) & 0x7) << 16) +#define MXC_CSPICTRL_TC (1 << 8) +#define MXC_CSPICTRL_RXOVF (1 << 6) +#define MXC_CSPICTRL_MAXBITS 0x1f #define MXC_CSPIPERIOD_32KHZ (1 << 15) @@ -65,12 +68,63 @@ static unsigned long spi_bases[] = { 0x53f84000, }; +#define OUT MX31_GPIO_DIRECTION_OUT +#define mxc_gpio_direction mx31_gpio_direction +#define mxc_gpio_set mx31_gpio_set +#elif defined(CONFIG_MX51) +#include +#include + +#define MXC_CSPIRXDATA 0x00 +#define MXC_CSPITXDATA 0x04 +#define MXC_CSPICTRL 0x08 +#define MXC_CSPICON 0x0C +#define MXC_CSPIINT 0x10 +#define MXC_CSPIDMA 0x14 +#define MXC_CSPISTAT 0x18 +#define MXC_CSPIPERIOD 0x1C +#define MXC_CSPIRESET 0x00 +#define MXC_CSPICTRL_EN (1 << 0) +#define MXC_CSPICTRL_MODE (1 << 1) +#define MXC_CSPICTRL_XCH (1 << 2) +#define MXC_CSPICTRL_CHIPSELECT(x) (((x) & 0x3) << 12) +#define MXC_CSPICTRL_BITCOUNT(x) (((x) & 0xfff) << 20) +#define MXC_CSPICTRL_PREDIV(x) (((x) & 0xF) << 12) +#define MXC_CSPICTRL_POSTDIV(x) (((x) & 0xF) << 8) +#define MXC_CSPICTRL_SELCHAN(x) (((x) & 0x3) << 18) +#define MXC_CSPICTRL_MAXBITS 0xfff +#define MXC_CSPICTRL_TC (1 << 7) +#define MXC_CSPICTRL_RXOVF (1 << 6) + +#define MXC_CSPIPERIOD_32KHZ (1 << 15) + +/* Bit position inside CTRL register to be associated with SS */ +#define MXC_CSPICTRL_CHAN 18 + +/* Bit position inside CON register to be associated with SS */ +#define MXC_CSPICON_POL 4 +#define MXC_CSPICON_PHA 0 +#define MXC_CSPICON_SSPOL 12 + +static unsigned long spi_bases[] = { + CSPI1_BASE_ADDR, + CSPI2_BASE_ADDR, + CSPI3_BASE_ADDR, +}; +#define mxc_gpio_direction(gpio, dir) (0) +#define mxc_gpio_set(gpio, value) {} +#define OUT 1 +#else +#error "Unsupported architecture" #endif struct mxc_spi_slave { struct spi_slave slave; unsigned long base; u32 ctrl_reg; +#if defined(CONFIG_MX51) + u32 cfg_reg; +#endif int gpio; }; @@ -89,34 +143,161 @@ static inline void reg_write(unsigned long addr, u32 val) *(volatile unsigned long*)addr = val; } +void spi_cs_activate(struct spi_slave *slave) +{ + struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); + if (mxcs->gpio > 0) + mxc_gpio_set(mxcs->gpio, mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL); +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); + if (mxcs->gpio > 0) + mxc_gpio_set(mxcs->gpio, + !(mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL)); +} + +#ifdef CONFIG_MX51 +static s32 spi_cfg(struct mxc_spi_slave *mxcs, unsigned int cs, + unsigned int max_hz, unsigned int mode) +{ + u32 clk_src = mxc_get_clock(MXC_CSPI_CLK); + s32 pre_div = 0, post_div = 0, i, reg_ctrl, reg_config; + u32 ss_pol = 0, sclkpol = 0, sclkpha = 0; + + if (max_hz == 0) { + printf("Error: desired clock is 0\n"); + return -1; + } + + reg_ctrl = reg_read(mxcs->base + MXC_CSPICTRL); + + /* Reset spi */ + reg_write(mxcs->base + MXC_CSPICTRL, 0); + reg_write(mxcs->base + MXC_CSPICTRL, (reg_ctrl | 0x1)); + + /* + * The following computation is taken directly from Freescale's code. + */ + if (clk_src > max_hz) { + pre_div = clk_src / max_hz; + if (pre_div > 16) { + post_div = pre_div / 16; + pre_div = 15; + } + if (post_div != 0) { + for (i = 0; i < 16; i++) { + if ((1 << i) >= post_div) + break; + } + if (i == 16) { + printf("Error: no divider for the freq: %d\n", + max_hz); + return -1; + } + post_div = i; + } + } + + debug("pre_div = %d, post_div=%d\n", pre_div, post_div); + reg_ctrl = (reg_ctrl & ~MXC_CSPICTRL_SELCHAN(3)) | + MXC_CSPICTRL_SELCHAN(cs); + reg_ctrl = (reg_ctrl & ~MXC_CSPICTRL_PREDIV(0x0F)) | + MXC_CSPICTRL_PREDIV(pre_div); + reg_ctrl = (reg_ctrl & ~MXC_CSPICTRL_POSTDIV(0x0F)) | + MXC_CSPICTRL_POSTDIV(post_div); + + /* always set to master mode */ + reg_ctrl |= 1 << (cs + 4); + + /* We need to disable SPI before changing registers */ + reg_ctrl &= ~MXC_CSPICTRL_EN; + + if (mode & SPI_CS_HIGH) + ss_pol = 1; + + if (!(mode & SPI_CPOL)) + sclkpol = 1; + + if (mode & SPI_CPHA) + sclkpha = 1; + + reg_config = reg_read(mxcs->base + MXC_CSPICON); + + /* + * Configuration register setup + * The MX51 has support different setup for each SS + */ + reg_config = (reg_config & ~(1 << (cs + MXC_CSPICON_SSPOL))) | + (ss_pol << (cs + MXC_CSPICON_SSPOL)); + reg_config = (reg_config & ~(1 << (cs + MXC_CSPICON_POL))) | + (sclkpol << (cs + MXC_CSPICON_POL)); + reg_config = (reg_config & ~(1 << (cs + MXC_CSPICON_PHA))) | + (sclkpha << (cs + MXC_CSPICON_PHA)); + + debug("reg_ctrl = 0x%x\n", reg_ctrl); + reg_write(mxcs->base + MXC_CSPICTRL, reg_ctrl); + debug("reg_config = 0x%x\n", reg_config); + reg_write(mxcs->base + MXC_CSPICON, reg_config); + + /* save config register and control register */ + mxcs->ctrl_reg = reg_ctrl; + mxcs->cfg_reg = reg_config; + + /* clear interrupt reg */ + reg_write(mxcs->base + MXC_CSPIINT, 0); + reg_write(mxcs->base + MXC_CSPISTAT, + MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); + + return 0; +} +#endif + static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen, unsigned long flags) { struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); - unsigned int cfg_reg = reg_read(mxcs->base + MXC_CSPICTRL); - mxcs->ctrl_reg = (mxcs->ctrl_reg & ~MXC_CSPICTRL_BITCOUNT(31)) | + if (flags & SPI_XFER_BEGIN) + spi_cs_activate(slave); + + mxcs->ctrl_reg = (mxcs->ctrl_reg & + ~MXC_CSPICTRL_BITCOUNT(MXC_CSPICTRL_MAXBITS)) | MXC_CSPICTRL_BITCOUNT(bitlen - 1); - if (cfg_reg != mxcs->ctrl_reg) - reg_write(mxcs->base + MXC_CSPICTRL, mxcs->ctrl_reg); + reg_write(mxcs->base + MXC_CSPICTRL, mxcs->ctrl_reg | MXC_CSPICTRL_EN); +#ifdef CONFIG_MX51 + reg_write(mxcs->base + MXC_CSPICON, mxcs->cfg_reg); +#endif - if (mxcs->gpio > 0 && (flags & SPI_XFER_BEGIN)) - mx31_gpio_set(mxcs->gpio, mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL); + /* Clear interrupt register */ + reg_write(mxcs->base + MXC_CSPISTAT, + MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); + debug("Sending SPI 0x%x\n", data); reg_write(mxcs->base + MXC_CSPITXDATA, data); - reg_write(mxcs->base + MXC_CSPICTRL, mxcs->ctrl_reg | MXC_CSPICTRL_XCH); + /* FIFO is written, now starts the transfer setting the XCH bit */ + reg_write(mxcs->base + MXC_CSPICTRL, mxcs->ctrl_reg | + MXC_CSPICTRL_EN | MXC_CSPICTRL_XCH); - while (reg_read(mxcs->base + MXC_CSPICTRL) & MXC_CSPICTRL_XCH) + /* Wait until the TC (Transfer completed) bit is set */ + while ((reg_read(mxcs->base + MXC_CSPISTAT) & MXC_CSPICTRL_TC) == 0) ; - if (mxcs->gpio > 0 && (flags & SPI_XFER_END)) { - mx31_gpio_set(mxcs->gpio, - !(mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL)); - } + /* Transfer completed, clear any pending request */ + reg_write(mxcs->base + MXC_CSPISTAT, + MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); + + data = reg_read(mxcs->base + MXC_CSPIRXDATA); + debug("SPI Rx: 0x%x\n", data); + + if (flags & SPI_XFER_END) + spi_cs_deactivate(slave); + + return data; - return reg_read(mxcs->base + MXC_CSPIRXDATA); } int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, @@ -176,7 +357,7 @@ static int decode_cs(struct mxc_spi_slave *mxcs, unsigned int cs) if (cs > 3) { mxcs->gpio = cs >> 8; cs &= 3; - ret = mx31_gpio_direction(mxcs->gpio, MX31_GPIO_DIRECTION_OUT); + ret = mxc_gpio_direction(mxcs->gpio, OUT); if (ret) { printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio); return -EINVAL; @@ -210,6 +391,20 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, cs = ret; + mxcs->slave.bus = bus; + mxcs->slave.cs = cs; + mxcs->base = spi_bases[bus]; + +#ifdef CONFIG_MX51 + /* Can be used for i.MX31 too ? */ + ctrl_reg = 0; + ret = spi_cfg(mxcs, cs, max_hz, mode); + if (ret) { + printf("mxc_spi: cannot setup SPI controller\n"); + free(mxcs); + return NULL; + } +#else ctrl_reg = MXC_CSPICTRL_CHIPSELECT(cs) | MXC_CSPICTRL_BITCOUNT(31) | MXC_CSPICTRL_DATARATE(7) | /* FIXME: calculate data rate */ @@ -222,12 +417,8 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, ctrl_reg |= MXC_CSPICTRL_POL; if (mode & SPI_CS_HIGH) ctrl_reg |= MXC_CSPICTRL_SSPOL; - - mxcs->slave.bus = bus; - mxcs->slave.cs = cs; - mxcs->base = spi_bases[bus]; mxcs->ctrl_reg = ctrl_reg; - +#endif return &mxcs->slave; } -- cgit v1.1 From d3588a55d4a041f2208290b8b6f9cecbdad179ac Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Sun, 18 Apr 2010 19:27:44 +0200 Subject: MX: Added definition file for MC13892 The MC13892 is a Power Controller used with processors of the family MX.51. The file adds definitions to be used to setup the internal registers via SPI. Signed-off-by: Stefano Babic --- include/mc13892.h | 160 ++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 160 insertions(+) create mode 100644 include/mc13892.h diff --git a/include/mc13892.h b/include/mc13892.h new file mode 100644 index 0000000..b291757 --- /dev/null +++ b/include/mc13892.h @@ -0,0 +1,160 @@ +/* + * (C) Copyright 2010 + * Stefano Babic, DENX Software Engineering, sbabic@denx.de. + * + * (C) Copyright 2009 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#ifndef __MC13892_H__ +#define __MC13892_H__ + +/* REG_CHARGE */ + +#define VCHRG0 0 +#define VCHRG1 (1 << 1) +#define VCHRG2 (1 << 2) +#define ICHRG0 (1 << 3) +#define ICHRG1 (1 << 4) +#define ICHRG2 (1 << 5) +#define ICHRG3 (1 << 6) +#define ICHRGTR0 (1 << 7) +#define ICHRGTR1 (1 << 8) +#define ICHRGTR2 (1 << 9) +#define FETOVRD (1 << 10) +#define FETCTRL (1 << 11) +#define RVRSMODE (1 << 13) +#define OVCTRL0 (1 << 15) +#define OVCTRL1 (1 << 16) +#define UCHEN (1 << 17) +#define CHRGLEDEN (1 << 18) +#define CHRGRAWPDEN (1 << 19) +#define CHGRESTART (1 << 20) +#define CHGAUTOB (1 << 21) +#define CYCLB (1 << 22) +#define CHGAUTOVIB (1 << 23) + +/* REG_SETTING_0/1 */ +#define VO_1_20V 0 +#define VO_1_30V 1 +#define VO_1_50V 2 +#define VO_1_80V 3 +#define VO_1_10V 4 +#define VO_2_00V 5 +#define VO_2_77V 6 +#define VO_2_40V 7 + +#define VIOL 2 +#define VDIG 4 +#define VGEN 6 + +/* SWxMode for Normal/Standby Mode */ +#define SWMODE_OFF_OFF 0 +#define SWMODE_PWM_OFF 1 +#define SWMODE_PWMPS_OFF 2 +#define SWMODE_PFM_OFF 3 +#define SWMODE_AUTO_OFF 4 +#define SWMODE_PWM_PWM 5 +#define SWMODE_PWM_AUTO 6 +#define SWMODE_AUTO_AUTO 8 +#define SWMODE_PWM_PWMPS 9 +#define SWMODE_PWMS_PWMPS 10 +#define SWMODE_PWMS_AUTO 11 +#define SWMODE_AUTO_PFM 12 +#define SWMODE_PWM_PFM 13 +#define SWMODE_PWMS_PFM 14 +#define SWMODE_PFM_PFM 15 +#define SWMODE_MASK 0x0F + +#define SWMODE1_SHIFT 0 +#define SWMODE2_SHIFT 10 +#define SWMODE3_SHIFT 0 +#define SWMODE4_SHIFT 8 + +/* Fields in REG_SETTING_1 */ +#define VVIDEO_2_7 (0 << 2) +#define VVIDEO_2_775 (1 << 2) +#define VVIDEO_2_5 (2 << 2) +#define VVIDEO_2_6 (3 << 2) +#define VVIDEO_MASK (3 << 2) +#define VAUDIO_2_3 (0 << 4) +#define VAUDIO_2_5 (1 << 4) +#define VAUDIO_2_775 (2 << 4) +#define VAUDIO_3_0 (3 << 4) +#define VAUDIO_MASK (3 << 4) +#define VSD_1_8 (0 << 6) +#define VSD_2_0 (1 << 6) +#define VSD_2_6 (2 << 6) +#define VSD_2_7 (3 << 6) +#define VSD_2_8 (4 << 6) +#define VSD_2_9 (5 << 6) +#define VSD_3_0 (6 << 6) +#define VSD_3_15 (7 << 6) +#define VSD_MASK (7 << 6) +#define VGEN1_1_2 0 +#define VGEN1_1_5 1 +#define VGEN1_2_775 2 +#define VGEN1_3_15 3 +#define VGEN1_MASK 3 +#define VGEN2_1_2 (0 << 6) +#define VGEN2_1_5 (1 << 6) +#define VGEN2_1_6 (2 << 6) +#define VGEN2_1_8 (3 << 6) +#define VGEN2_2_7 (4 << 6) +#define VGEN2_2_8 (5 << 6) +#define VGEN2_3_0 (6 << 6) +#define VGEN2_3_15 (7 << 6) +#define VGEN2_MASK (7 << 6) + +/* Fields in REG_SETTING_1 */ +#define VGEN3_1_8 (0 << 14) +#define VGEN3_2_9 (1 << 14) +#define VGEN3_MASK (1 << 14) +#define VDIG_1_05 (0 << 4) +#define VDIG_1_25 (1 << 4) +#define VDIG_1_65 (2 << 4) +#define VDIG_1_8 (3 << 4) +#define VDIG_MASK (3 << 4) +#define VCAM_2_5 (0 << 16) +#define VCAM_2_6 (1 << 16) +#define VCAM_2_75 (2 << 16) +#define VCAM_3_0 (3 << 16) +#define VCAM_MASK (3 << 16) + +/* Reg Mode 1 */ +#define VGEN3EN (1 << 0) +#define VGEN3STBY (1 << 1) +#define VGEN3MODE (1 << 2) +#define VGEN3CONFIG (1 << 3) +#define VCAMEN (1 << 6) +#define VCAMSTBY (1 << 7) +#define VCAMMODE (1 << 8) +#define VCAMCONFIG (1 << 9) +#define VVIDEOEN (1 << 12) +#define VIDEOSTBY (1 << 13) +#define VVIDEOMODE (1 << 14) +#define VAUDIOEN (1 << 15) +#define VAUDIOSTBY (1 << 16) +#define VSDEN (1 << 18) +#define VSDSTBY (1 << 19) +#define VSDMODE (1 << 20) + +#endif -- cgit v1.1 From b4377e12e9aa0b3bf2dcae0a0f02ec9086338506 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Tue, 16 Mar 2010 17:22:21 +0100 Subject: Add SPI support to mx51evk board The patch adds SPI devices to the mx51evk board. The MC13892 chip (PMIC) is supported. Signed-off-by: Stefano Babic --- board/freescale/mx51evk/mx51evk.c | 139 ++++++++++++++++++++++++++++++++++++++ include/configs/mx51evk.h | 15 ++++ 2 files changed, 154 insertions(+) diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 3d89be3..75d642b 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -27,9 +27,12 @@ #include #include #include +#include #include #include #include +#include +#include #include "mx51evk.h" DECLARE_GLOBAL_DATA_PTR; @@ -147,6 +150,130 @@ static void setup_iomux_fec(void) mxc_iomux_set_pad(MX51_PIN_NANDF_D11, 0x2180); } +#ifdef CONFIG_MXC_SPI +static void setup_iomux_spi(void) +{ + /* 000: Select mux mode: ALT0 mux port: MOSI of instance: ecspi1 */ + mxc_request_iomux(MX51_PIN_CSPI1_MOSI, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_MOSI, 0x105); + + /* 000: Select mux mode: ALT0 mux port: MISO of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_MISO, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_MISO, 0x105); + + /* de-select SS1 of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_SS1, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SS1, 0x85); + + /* 000: Select mux mode: ALT0 mux port: SS0 ecspi1 */ + mxc_request_iomux(MX51_PIN_CSPI1_SS0, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SS0, 0x185); + + /* 000: Select mux mode: ALT0 mux port: RDY of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_RDY, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_RDY, 0x180); + + /* 000: Select mux mode: ALT0 mux port: SCLK of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_SCLK, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SCLK, 0x105); +} +#endif + +static void power_init(void) +{ + unsigned int val; + unsigned int reg; + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE; + + /* Write needed to Power Gate 2 register */ + val = pmic_reg_read(REG_POWER_MISC); + val &= ~PWGT2SPIEN; + pmic_reg_write(REG_POWER_MISC, val); + + /* Write needed to update Charger 0 */ + pmic_reg_write(REG_CHARGE, VCHRG0 | VCHRG1 | VCHRG2 | + ICHRG0 | ICHRG1 | ICHRG2 | ICHRG3 | ICHRGTR0 | + OVCTRL1 | UCHEN | CHRGLEDEN | CYCLB); + + /* power up the system first */ + pmic_reg_write(REG_POWER_MISC, PWUP); + + /* Set core voltage to 1.1V */ + val = pmic_reg_read(REG_SW_0); + val = (val & (~0x1F)) | 0x14; + pmic_reg_write(REG_SW_0, val); + + /* Setup VCC (SW2) to 1.25 */ + val = pmic_reg_read(REG_SW_1); + val = (val & (~0x1F)) | 0x1A; + pmic_reg_write(REG_SW_1, val); + + /* Setup 1V2_DIG1 (SW3) to 1.25 */ + val = pmic_reg_read(REG_SW_2); + val = (val & (~0x1F)) | 0x1A; + pmic_reg_write(REG_SW_2, val); + udelay(50); + + /* Raise the core frequency to 800MHz */ + writel(0x0, &mxc_ccm->cacrr); + + /* Set switchers in Auto in NORMAL mode & STANDBY mode */ + /* Setup the switcher mode for SW1 & SW2*/ + val = pmic_reg_read(REG_SW_4); + val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) | + (SWMODE_MASK << SWMODE2_SHIFT))); + val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) | + (SWMODE_AUTO_AUTO << SWMODE2_SHIFT); + pmic_reg_write(REG_SW_4, val); + + /* Setup the switcher mode for SW3 & SW4 */ + val = pmic_reg_read(REG_SW_5); + val = (val & ~((SWMODE_MASK << SWMODE3_SHIFT) | + (SWMODE_MASK << SWMODE4_SHIFT))); + val |= (SWMODE_AUTO_AUTO << SWMODE3_SHIFT) | + (SWMODE_AUTO_AUTO << SWMODE4_SHIFT); + pmic_reg_write(REG_SW_5, val); + + /* Set VDIG to 1.65V, VGEN3 to 1.8V, VCAM to 2.6V */ + val = pmic_reg_read(REG_SETTING_0); + val &= ~(VCAM_MASK | VGEN3_MASK | VDIG_MASK); + val |= VDIG_1_65 | VGEN3_1_8 | VCAM_2_6; + pmic_reg_write(REG_SETTING_0, val); + + /* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */ + val = pmic_reg_read(REG_SETTING_1); + val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK); + val |= VSD_3_15 | VAUDIO_3_0 | VVIDEO_2_775; + pmic_reg_write(REG_SETTING_1, val); + + /* Configure VGEN3 and VCAM regulators to use external PNP */ + val = VGEN3CONFIG | VCAMCONFIG; + pmic_reg_write(REG_MODE_1, val); + udelay(200); + + reg = readl(GPIO2_BASE_ADDR + 0x0); + reg &= ~0x4000; /* Lower reset line */ + writel(reg, GPIO2_BASE_ADDR + 0x0); + + reg = readl(GPIO2_BASE_ADDR + 0x4); + reg |= 0x4000; /* configure GPIO lines as output */ + writel(reg, GPIO2_BASE_ADDR + 0x4); + + /* Reset the ethernet controller over GPIO */ + writel(0x1, IOMUXC_BASE_ADDR + 0x0AC); + + /* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */ + val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG | + VVIDEOEN | VAUDIOEN | VSDEN; + pmic_reg_write(REG_MODE_1, val); + + udelay(500); + + reg = readl(GPIO2_BASE_ADDR + 0x0); + reg |= 0x4000; + writel(reg, GPIO2_BASE_ADDR + 0x0); +} + #ifdef CONFIG_FSL_ESDHC int board_mmc_getcd(u8 *cd, struct mmc *mmc) { @@ -284,9 +411,21 @@ int board_init(void) setup_iomux_uart(); setup_iomux_fec(); + return 0; } +#ifdef BOARD_LATE_INIT +int board_late_init(void) +{ +#ifdef CONFIG_MXC_SPI + setup_iomux_spi(); + power_init(); +#endif + return 0; +} +#endif + int checkboard(void) { puts("Board: MX51EVK "); diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index 3626df7..86a4731 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -54,6 +54,8 @@ /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_SIZE 128 +#define BOARD_LATE_INIT + /* * Hardware drivers */ @@ -61,6 +63,19 @@ #define CONFIG_SYS_MX51_UART1 /* + * SPI Configs + * */ +#define CONFIG_CMD_SPI + +#define CONFIG_MXC_SPI + +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_BUS 0 +#define CONFIG_FSL_PMIC_CS 0 +#define CONFIG_FSL_PMIC_CLK 2500000 +#define CONFIG_FSL_PMIC_MODE (SPI_CPOL | SPI_CS_HIGH) + +/* * MMC Configs * */ #define CONFIG_FSL_ESDHC -- cgit v1.1 From 03af5abd85637d27e96fb999ce6e3992293570b0 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Thu, 13 May 2010 10:26:40 +0200 Subject: MX31: Added support for the Casio COM57H5M10XRC to QONG The patch adds setup to connect a CASIO COM57H5M10XRC (640x480 TFT display) to the QONG module. Signed-off-by: Stefano Babic --- drivers/video/mx3fb.c | 47 +++++++++++++++++++++++++++++++---------------- include/configs/qong.h | 2 +- 2 files changed, 32 insertions(+), 17 deletions(-) diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c index 99a595e..7f04b49 100644 --- a/drivers/video/mx3fb.c +++ b/drivers/video/mx3fb.c @@ -56,22 +56,7 @@ void lcd_panel_disable(void) #define msleep(a) udelay(a * 1000) -#ifndef CONFIG_DISPLAY_VBEST_VGG322403 -#define XRES 240 -#define YRES 320 -#define PANEL_TYPE IPU_PANEL_TFT -#define PIXEL_CLK 185925 -#define PIXEL_FMT IPU_PIX_FMT_RGB666 -#define H_START_WIDTH 9 /* left_margin */ -#define H_SYNC_WIDTH 1 /* hsync_len */ -#define H_END_WIDTH (16 + 1) /* right_margin + hsync_len */ -#define V_START_WIDTH 7 /* upper_margin */ -#define V_SYNC_WIDTH 1 /* vsync_len */ -#define V_END_WIDTH (9 + 1) /* lower_margin + vsync_len */ -#define SIG_POL (DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL) -#define IF_CONF 0 -#define IF_CLK_DIV 0x175 -#else /* Display Vbest VGG322403 */ +#if defined(CONFIG_DISPLAY_VBEST_VGG322403) #define XRES 320 #define YRES 240 #define PANEL_TYPE IPU_PANEL_TFT @@ -86,6 +71,36 @@ void lcd_panel_disable(void) #define SIG_POL (DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL) #define IF_CONF 0 #define IF_CLK_DIV 0x175 +#elif defined(CONFIG_DISPLAY_COM57H5M10XRC) +#define XRES 640 +#define YRES 480 +#define PANEL_TYPE IPU_PANEL_TFT +#define PIXEL_CLK 40000 +#define PIXEL_FMT IPU_PIX_FMT_RGB666 +#define H_START_WIDTH 120 /* left_margin */ +#define H_SYNC_WIDTH 30 /* hsync_len */ +#define H_END_WIDTH (10 + 30) /* right_margin + hsync_len */ +#define V_START_WIDTH 35 /* upper_margin */ +#define V_SYNC_WIDTH 3 /* vsync_len */ +#define V_END_WIDTH (7 + 3) /* lower_margin + vsync_len */ +#define SIG_POL (DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL) +#define IF_CONF 0 +#define IF_CLK_DIV 0x175 +#else +#define XRES 240 +#define YRES 320 +#define PANEL_TYPE IPU_PANEL_TFT +#define PIXEL_CLK 185925 +#define PIXEL_FMT IPU_PIX_FMT_RGB666 +#define H_START_WIDTH 9 /* left_margin */ +#define H_SYNC_WIDTH 1 /* hsync_len */ +#define H_END_WIDTH (16 + 1) /* right_margin + hsync_len */ +#define V_START_WIDTH 7 /* upper_margin */ +#define V_SYNC_WIDTH 1 /* vsync_len */ +#define V_END_WIDTH (9 + 1) /* lower_margin + vsync_len */ +#define SIG_POL (DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL) +#define IF_CONF 0 +#define IF_CLK_DIV 0x175 #endif #define LCD_COLOR_IPU LCD_COLOR16 diff --git a/include/configs/qong.h b/include/configs/qong.h index eb4669b..100fa3f 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -84,7 +84,7 @@ #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP -#define CONFIG_DISPLAY_VBEST_VGG322403 +#define CONFIG_DISPLAY_COM57H5M10XRC /* * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the -- cgit v1.1