From 55429a0323c8b39618b0005a7b8e496c5f8da997 Mon Sep 17 00:00:00 2001
From: Marek Vasut <marek.vasut@gmail.com>
Date: Mon, 5 Apr 2010 02:28:14 +0200
Subject: PXA: PXAMMC: Drop different delays for PXA27X

In case the delays were set to 10000, the MMC card on PXA27X boards (and PXA3xx
boards) didn't initialize on first try. Increasing the delays and leaving just
those for PXA25x and 26x (that is 200000) fixes this problem.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
 drivers/mmc/pxa_mmc.c | 8 --------
 1 file changed, 8 deletions(-)

diff --git a/drivers/mmc/pxa_mmc.c b/drivers/mmc/pxa_mmc.c
index 8225235..b155541 100644
--- a/drivers/mmc/pxa_mmc.c
+++ b/drivers/mmc/pxa_mmc.c
@@ -584,11 +584,7 @@ mmc_legacy_init(int verbose)
 			debug("Detected SD card\n");
 			break;
 		}
-#ifdef CONFIG_PXA27X
-		udelay(10000);
-#else
 		udelay(200000);
-#endif
 	}
 
 	if (retries <= 0 || !(IF_TYPE_SD == mmc_dev.if_type)) {
@@ -598,11 +594,7 @@ mmc_legacy_init(int verbose)
 
 		retries = 10;
 		while (retries-- && resp && !(resp[0] & 0x80000000)) {
-#ifdef CONFIG_PXA27X
-			udelay(10000);
-#else
 			udelay(200000);
-#endif
 			resp =
 			    mmc_cmd(MMC_CMD_SEND_OP_COND, 0x00ff, 0x8000,
 				    MMC_CMDAT_R3);
-- 
cgit v1.1


From 43c15d3dd570be97d44944cade99ab03e6d5491e Mon Sep 17 00:00:00 2001
From: Marek Vasut <marek.vasut@gmail.com>
Date: Wed, 14 Oct 2009 00:25:33 +0200
Subject: PXA: PXAMMC: Add Monahans support

This patch enables PXAMCI support on PXA3xx CPUs. This patch only enables MMC1
though, MMC2 and PXA31x MMC3 will need further patch to be operational.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
 drivers/mmc/pxa_mmc.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/mmc/pxa_mmc.c b/drivers/mmc/pxa_mmc.c
index b155541..8776903 100644
--- a/drivers/mmc/pxa_mmc.c
+++ b/drivers/mmc/pxa_mmc.c
@@ -126,7 +126,7 @@ mmc_block_read(uchar * dst, ulong src, ulong len)
 	MMC_I_MASK = ~MMC_I_MASK_RXFIFO_RD_REQ;
 	while (len) {
 		if (MMC_I_REG & MMC_I_REG_RXFIFO_RD_REQ) {
-#ifdef CONFIG_PXA27X
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
 			int i;
 			for (i = min(len, 32); i; i--) {
 				*dst++ = *((volatile uchar *)&MMC_RXFIFO);
@@ -558,8 +558,11 @@ mmc_legacy_init(int verbose)
 	set_GPIO_mode(GPIO6_MMCCLK_MD);
 	set_GPIO_mode(GPIO8_MMCCS0_MD);
 #endif
+#ifdef CONFIG_CPU_MONAHANS	/* pxa3xx */
+	CKENA |= CKENA_12_MMC0 | CKENA_13_MMC1;
+#else	/* pxa2xx */
 	CKEN |= CKEN12_MMC;	/* enable MMC unit clock */
-
+#endif
 	MMC_CLKRT = MMC_CLKRT_0_3125MHZ;
 	MMC_RESTO = MMC_RES_TO_MAX;
 	MMC_SPI = MMC_SPI_DISABLE;
@@ -624,7 +627,7 @@ mmc_legacy_init(int verbose)
 	MMC_CLKRT = 0;		/* 20 MHz */
 	resp = mmc_cmd(MMC_CMD_SELECT_CARD, rca, 0, MMC_CMDAT_R1);
 
-#ifdef CONFIG_PXA27X
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
 	if (IF_TYPE_SD == mmc_dev.if_type) {
 		resp = mmc_cmd(MMC_CMD_APP_CMD, rca, 0, MMC_CMDAT_R1);
 		resp = mmc_cmd(SD_CMD_APP_SET_BUS_WIDTH, 0, 2, MMC_CMDAT_R1);
-- 
cgit v1.1


From 52dc45e5a3e60251329096400da5a9bb6a12ccbf Mon Sep 17 00:00:00 2001
From: Marek Vasut <marek.vasut@gmail.com>
Date: Fri, 16 Apr 2010 22:25:14 +0200
Subject: PXA: Add UP2OCR register bit definitions

This register is used on PXA to control the USB Port2 operation (USB Port2 is
the host port).

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
 arch/arm/include/asm/arch-pxa/pxa-regs.h | 22 ++++++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

diff --git a/arch/arm/include/asm/arch-pxa/pxa-regs.h b/arch/arm/include/asm/arch-pxa/pxa-regs.h
index a25d4c5..7cd7a14 100644
--- a/arch/arm/include/asm/arch-pxa/pxa-regs.h
+++ b/arch/arm/include/asm/arch-pxa/pxa-regs.h
@@ -992,10 +992,6 @@ typedef void		(*ExcpHndlr) (void) ;
 #define UHCHIE		__REG(0x4C000068)
 #define UHCHIT		__REG(0x4C00006C)
 
-#if defined(CONFIG_CPU_MONAHANS)
-#define UP2OCR		__REG(0x40600020)
-#endif
-
 #define UHCHR_FSBIR	(1<<0)
 #define UHCHR_FHR	(1<<1)
 #define UHCHR_CGR	(1<<2)
@@ -1015,6 +1011,24 @@ typedef void		(*ExcpHndlr) (void) ;
 #define UHCHIE_HBAIE	(1<<8)
 #define UHCHIE_RWIE	(1<<7)
 
+#if defined(CONFIG_CPU_MONAHANS) || defined(CONFIG_PXA27X)
+#define UP2OCR		__REG(0x40600020)
+#endif
+
+#define UP2OCR_HXOE	(1<<17)
+#define UP2OCR_HXS	(1<<16)
+#define UP2OCR_IDON	(1<<10)
+#define UP2OCR_EXSUS	(1<<9)
+#define UP2OCR_EXSP	(1<<8)
+#define UP2OCR_DMSTATE	(1<<7)
+#define UP2OCR_VPM	(1<<6)
+#define UP2OCR_DPSTATE	(1<<5)
+#define UP2OCR_DPPUE	(1<<4)
+#define UP2OCR_DMPDE	(1<<3)
+#define UP2OCR_DPPDE	(1<<2)
+#define UP2OCR_CPVPE	(1<<1)
+#define UP2OCR_CPVEN	(1<<0)
+
 #endif
 
 /*
-- 
cgit v1.1


From bb596e84ebd6e43d862b13755419b8a3e01b4f51 Mon Sep 17 00:00:00 2001
From: Marek Vasut <marek.vasut@gmail.com>
Date: Sat, 17 Apr 2010 00:35:52 +0200
Subject: PXA: Add missing MDREFR bits

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
 arch/arm/include/asm/arch-pxa/pxa-regs.h | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/include/asm/arch-pxa/pxa-regs.h b/arch/arm/include/asm/arch-pxa/pxa-regs.h
index 7cd7a14..cd7b7f9 100644
--- a/arch/arm/include/asm/arch-pxa/pxa-regs.h
+++ b/arch/arm/include/asm/arch-pxa/pxa-regs.h
@@ -2421,6 +2421,9 @@ typedef void		(*ExcpHndlr) (void) ;
 #define MDMRS		__REG(0x48000040)  /* MRS value to be written to SDRAM */
 #define BOOT_DEF	__REG(0x48000044)  /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
 
+#define MDREFR_ALTREFA	(1 << 31)	/* Exiting Alternate Bus Master Mode Refresh Control */
+#define MDREFR_ALTREFB	(1 << 30)	/* Entering Alternate Bus Master Mode Refresh Control */
+#define MDREFR_K0DB4	(1 << 29)	/* SDCLK0 Divide by 4 Control/Status */
 #define MDREFR_K2FREE	(1 << 25)	/* SDRAM Free-Running Control */
 #define MDREFR_K1FREE	(1 << 24)	/* SDRAM Free-Running Control */
 #define MDREFR_K0FREE	(1 << 23)	/* SDRAM Free-Running Control */
-- 
cgit v1.1


From 0e42ada3107709149b708f6ddc3ad7d9b9017fbb Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Thu, 27 May 2010 23:18:33 +0200
Subject: Fix printing of make targets, simplify Makefile

Make printing the "board names" more useful. So far, we would get
output like this;

$ ./MAKEALL P2020RDB P2020RDB_NAND P2020RDB_SDCARD P2020RDB_SPIFLASH
Configuring for P1_P2_RDB board...
   text    data     bss     dec     hex filename
 342612   32656  265212  640480   9c5e0 /work/wd/tmp-ppc/u-boot
Configuring for P1_P2_RDB board...
   text    data     bss     dec     hex filename
 343160   32704  265212  641076   9c834 /work/wd/tmp-ppc/u-boot
Configuring for P1_P2_RDB board...
   text    data     bss     dec     hex filename
 341908   32620  265212  639740   9c2fc /work/wd/tmp-ppc/u-boot
Configuring for P1_P2_RDB board...
   text    data     bss     dec     hex filename
 341908   32620  265212  639740   9c2fc /work/wd/tmp-ppc/u-boot

For all build targets the same board name would be printed, which
makes is often pretty difficult to find out which exact build target
caused problems. With this commit, the real make target name gets
printed instead, which is way more useful:

$ ./MAKEALL P2020RDB P2020RDB_NAND P2020RDB_SDCARD P2020RDB_SPIFLASH
Configuring for P2020RDB board...
   text    data     bss     dec     hex filename
 342612   32656  265212  640480   9c5e0 /work/wd/tmp-ppc/u-boot
Configuring for P2020RDB_NAND board...
   text    data     bss     dec     hex filename
 343160   32704  265212  641076   9c834 /work/wd/tmp-ppc/u-boot
Configuring for P2020RDB_SDCARD board...
   text    data     bss     dec     hex filename
 341908   32620  265212  639740   9c2fc /work/wd/tmp-ppc/u-boot
Configuring for P2020RDB_SPIFLASH board...
   text    data     bss     dec     hex filename
 341908   32620  265212  639740   9c2fc /work/wd/tmp-ppc/u-boot

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
---
 Makefile | 694 +++++++++++++++++++++------------------------------------------
 1 file changed, 230 insertions(+), 464 deletions(-)

diff --git a/Makefile b/Makefile
index 9b14733..c83bf84 100644
--- a/Makefile
+++ b/Makefile
@@ -467,7 +467,7 @@ CHANGELOG:
 	unexpand -a | sed -e 's/\s\s*$$//' > $@
 
 include/license.h: tools/bin2header COPYING
-	 cat COPYING | gzip -9 -c | ./tools/bin2header license_gzip > include/license.h
+	cat COPYING | gzip -9 -c | ./tools/bin2header license_gzip > include/license.h
 #########################################################################
 
 unconfig:
@@ -518,20 +518,16 @@ digsy_mtc_RAMBOOT_config:	unconfig
 	@mkdir -p $(obj)board/digsy_mtc
 	@ >$(obj)include/config.h
 	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFF000000" >$(obj)board/digsy_mtc/config.tmp ; \
-		  echo "... with LOWBOOT configuration" ; \
-		}
+		echo "TEXT_BASE = 0xFF000000" >$(obj)board/digsy_mtc/config.tmp
 	@[ -z "$(findstring RAMBOOT_,$@)" ] || \
-		{ echo "TEXT_BASE = 0x00100000" >$(obj)board/digsy_mtc/config.tmp ; \
-		  echo "... with RAMBOOT configuration" ; \
-		}
-	@$(MKCONFIG) -a digsy_mtc  powerpc mpc5xxx digsy_mtc
+		echo "TEXT_BASE = 0x00100000" >$(obj)board/digsy_mtc/config.tmp
+	@$(MKCONFIG) -n $@ -a digsy_mtc  powerpc mpc5xxx digsy_mtc
 
 galaxy5200_LOWBOOT_config \
 galaxy5200_config:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_$(@:_config=) 1" >$(obj)include/config.h
-	@$(MKCONFIG) -a galaxy5200 powerpc mpc5xxx galaxy5200
+	@$(MKCONFIG) -n $@ -a galaxy5200 powerpc mpc5xxx galaxy5200
 
 hmi1001_config:	unconfig
 	@$(MKCONFIG) hmi1001 powerpc mpc5xxx hmi1001
@@ -548,22 +544,15 @@ icecube_5200_DDR_LOWBOOT08_config:	unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/icecube
 	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
-		{ if [ "$(findstring DDR,$@)" ] ; \
+		if [ "$(findstring DDR,$@)" ] ; \
 			then echo "TEXT_BASE = 0xFF800000" >$(obj)board/icecube/config.tmp ; \
 			else echo "TEXT_BASE = 0xFF000000" >$(obj)board/icecube/config.tmp ; \
-		  fi ; \
-		  $(XECHO) "... with LOWBOOT configuration" ; \
-		}
+		fi
 	@[ -z "$(findstring LOWBOOT08,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFF800000" >$(obj)board/icecube/config.tmp ; \
-		  echo "... with 8 MB flash only" ; \
-		  $(XECHO) "... with LOWBOOT configuration" ; \
-		}
+		echo "TEXT_BASE = 0xFF800000" >$(obj)board/icecube/config.tmp
 	@[ -z "$(findstring DDR,$@)" ] || \
-		{ echo "#define CONFIG_MPC5200_DDR"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... DDR memory revision" ; \
-		}
-	@$(MKCONFIG) -a IceCube powerpc mpc5xxx icecube
+		echo "#define CONFIG_MPC5200_DDR" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a IceCube powerpc mpc5xxx icecube
 
 jupiter_config:	unconfig
 	@$(MKCONFIG) jupiter powerpc mpc5xxx jupiter
@@ -580,17 +569,12 @@ lite5200b_LOWBOOT_config:	unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/icecube
 	@ echo "#define CONFIG_MPC5200_DDR"	>>$(obj)include/config.h
-	@ $(XECHO) "... DDR memory revision"
 	@ echo "#define CONFIG_LITE5200B"	>>$(obj)include/config.h
 	@[ -z "$(findstring _PM_,$@)" ] || \
-		{ echo "#define CONFIG_LITE5200B_PM"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with power management (low-power mode) support" ; \
-		}
+		echo "#define CONFIG_LITE5200B_PM" >>$(obj)include/config.h
 	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFF000000" >$(obj)board/icecube/config.tmp ; \
-		  $(XECHO) "... with LOWBOOT configuration" ; \
-		}
-	@$(MKCONFIG) -a IceCube  powerpc mpc5xxx icecube
+		echo "TEXT_BASE = 0xFF000000" >$(obj)board/icecube/config.tmp
+	@$(MKCONFIG) -n $@ -a IceCube  powerpc mpc5xxx icecube
 
 mcc200_config	\
 mcc200_SDRAM_config	\
@@ -606,38 +590,22 @@ prs200_highboot_config	\
 prs200_highboot_DDR_config:	unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/mcc200
-	@[ -n "$(findstring highboot,$@)" ] || \
-		{ $(XECHO) "... with lowboot configuration" ; \
-		}
 	@[ -z "$(findstring highboot,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFFF00000" >$(obj)board/mcc200/config.tmp ; \
-		  $(XECHO) "... with highboot configuration" ; \
-		}
+		echo "TEXT_BASE = 0xFFF00000" >$(obj)board/mcc200/config.tmp
 	@[ -n "$(findstring _SDRAM,$@)" ] || \
-		{ if [ -n "$(findstring mcc200,$@)" ]; \
-		  then \
-			$(XECHO) "... with DDR" ; \
-		  else \
-			if [ -n "$(findstring _DDR,$@)" ];\
+		if [ -n "$(findstring prs200,$@)" ]; \
+		then \
+			if [ -z "$(findstring _DDR,$@)" ];\
 			then \
-				$(XECHO) "... with DDR" ; \
-			else \
 				echo "#define CONFIG_MCC200_SDRAM" >>$(obj)include/config.h ;\
-				$(XECHO) "... with SDRAM" ; \
 			fi; \
-		  fi; \
-		}
+		fi
 	@[ -z "$(findstring _SDRAM,$@)" ] || \
-		{ echo "#define CONFIG_MCC200_SDRAM"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with SDRAM" ; \
-		}
+		echo "#define CONFIG_MCC200_SDRAM" >>$(obj)include/config.h
 	@[ -z "$(findstring COM12,$@)" ] || \
-		{ echo "#define CONFIG_CONSOLE_COM12"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with console on COM12" ; \
-		}
+		echo "#define CONFIG_CONSOLE_COM12" >>$(obj)include/config.h
 	@[ -z "$(findstring prs200,$@)" ] || \
-		{ echo "#define CONFIG_PRS200"	>>$(obj)include/config.h ;\
-		}
+		echo "#define CONFIG_PRS200" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a mcc200 powerpc mpc5xxx mcc200
 
 mecp5200_config:  unconfig
@@ -657,7 +625,7 @@ MVBC_P_config: unconfig
 	@mkdir -p $(obj)board/mvbc_p
 	@ >$(obj)include/config.h
 	@[ -z "$(findstring MVBC_P,$@)" ] || \
-	{   	echo "#define CONFIG_MVBC_P" 	>>$(obj)include/config.h; }
+		echo "#define CONFIG_MVBC_P" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a MVBC_P powerpc mpc5xxx mvbc_p matrix_vision
 
 MVSMR_config: unconfig
@@ -673,10 +641,8 @@ pcm030_LOWBOOT_config:	unconfig
 	@mkdir -p $(obj)include $(obj)board/phytec/pcm030
 	@ >$(obj)include/config.h
 	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFF000000"	>$(obj)board/phytec/pcm030/config.tmp ; \
-		  echo "... with LOWBOOT configuration" ; \
-		}
-	@$(MKCONFIG) -a pcm030 powerpc mpc5xxx pcm030 phytec
+		echo "TEXT_BASE = 0xFF000000" >$(obj)board/phytec/pcm030/config.tmp
+	@$(MKCONFIG) -n $@ -a pcm030 powerpc mpc5xxx pcm030 phytec
 
 pf5200_config:	unconfig
 	@$(MKCONFIG) pf5200  powerpc mpc5xxx pf5200 esd
@@ -687,14 +653,10 @@ PM520_ROMBOOT_config \
 PM520_ROMBOOT_DDR_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring DDR,$@)" ] || \
-		{ echo "#define CONFIG_MPC5200_DDR"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... DDR memory revision" ; \
-		}
+		echo "#define CONFIG_MPC5200_DDR" >>$(obj)include/config.h
 	@[ -z "$(findstring ROMBOOT,$@)" ] || \
-		{ echo "#define CONFIG_BOOT_ROM" >>$(obj)include/config.h ; \
-		  $(XECHO) "... booting from 8-bit flash" ; \
-		}
-	@$(MKCONFIG) -a PM520 powerpc mpc5xxx pm520
+		echo "#define CONFIG_BOOT_ROM" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a PM520 powerpc mpc5xxx pm520
 
 smmaco4_config: unconfig
 	@$(MKCONFIG) -a smmaco4 powerpc mpc5xxx tqm5200 tqc
@@ -706,9 +668,7 @@ TB5200_B_config \
 TB5200_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring _B,$@)" ] || \
-		{ echo "#define CONFIG_TQM5200_B"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with MPC5200B processor" ; \
-		}
+		echo "#define CONFIG_TQM5200_B"	>>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a TB5200 powerpc mpc5xxx tqm5200 tqc
 
 MINI5200_config	\
@@ -725,18 +685,12 @@ Total5200_Rev2_lowboot_config:	unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/total5200
 	@[ -n "$(findstring Rev,$@)" ] || \
-		{ echo "#define CONFIG_TOTAL5200_REV 1"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... revision 1 board" ; \
-		}
+		echo "#define CONFIG_TOTAL5200_REV 1" >>$(obj)include/config.h
 	@[ -z "$(findstring Rev2_,$@)" ] || \
-		{ echo "#define CONFIG_TOTAL5200_REV 2"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... revision 2 board" ; \
-		}
+		echo "#define CONFIG_TOTAL5200_REV 2" >>$(obj)include/config.h
 	@[ -z "$(findstring lowboot_,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFE000000" >$(obj)board/total5200/config.tmp ; \
-		  $(XECHO) "... with lowboot configuration" ; \
-		}
-	@$(MKCONFIG) -a Total5200 powerpc mpc5xxx total5200
+		echo "TEXT_BASE = 0xFE000000" >$(obj)board/total5200/config.tmp
+	@$(MKCONFIG) -n $@ -a Total5200 powerpc mpc5xxx total5200
 
 cam5200_config \
 cam5200_niosflash_config \
@@ -751,37 +705,26 @@ TQM5200_STK100_config:	unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/tqc/tqm5200
 	@[ -z "$(findstring cam5200,$@)" ] || \
-		{ echo "#define CONFIG_CAM5200"	>>$(obj)include/config.h ; \
-		  echo "#define CONFIG_TQM5200S"	>>$(obj)include/config.h ; \
-		  echo "#define CONFIG_TQM5200_B"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... TQM5200S on Cam5200" ; \
+		{ echo "#define CONFIG_CAM5200"	  >>$(obj)include/config.h ; \
+		  echo "#define CONFIG_TQM5200S"  >>$(obj)include/config.h ; \
+		  echo "#define CONFIG_TQM5200_B" >>$(obj)include/config.h ; \
 		}
 	@[ -z "$(findstring niosflash,$@)" ] || \
-		{ echo "#define CONFIG_CAM5200_NIOSFLASH"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with NIOS flash driver" ; \
-		}
+		echo "#define CONFIG_CAM5200_NIOSFLASH"	>>$(obj)include/config.h
 	@[ -z "$(findstring fo300,$@)" ] || \
-		{ echo "#define CONFIG_FO300"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... TQM5200 on FO300" ; \
-		}
+		echo "#define CONFIG_FO300" >>$(obj)include/config.h
 	@[ -z "$(findstring MiniFAP,$@)" ] || \
-		{ echo "#define CONFIG_MINIFAP"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... TQM5200_AC on MiniFAP" ; \
-		}
+		echo "#define CONFIG_MINIFAP" >>$(obj)include/config.h
 	@[ -z "$(findstring STK100,$@)" ] || \
-		{ echo "#define CONFIG_STK52XX_REV100"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... on a STK52XX.100 base board" ; \
-		}
+		echo "#define CONFIG_STK52XX_REV100" >>$(obj)include/config.h
 	@[ -z "$(findstring TQM5200_B,$@)" ] || \
-		{ echo "#define CONFIG_TQM5200_B"	>>$(obj)include/config.h ; \
-		}
+		echo "#define CONFIG_TQM5200_B"	>>$(obj)include/config.h
 	@[ -z "$(findstring TQM5200S,$@)" ] || \
-		{ echo "#define CONFIG_TQM5200S"	>>$(obj)include/config.h ; \
-		  echo "#define CONFIG_TQM5200_B"	>>$(obj)include/config.h ; \
+		{ echo "#define CONFIG_TQM5200S"  >>$(obj)include/config.h ; \
+		  echo "#define CONFIG_TQM5200_B" >>$(obj)include/config.h ; \
 		}
 	@[ -z "$(findstring HIGHBOOT,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFFF00000" >$(obj)board/tqm5200/config.tmp ; \
-		}
+		echo "TEXT_BASE = 0xFFF00000" >$(obj)board/tqm5200/config.tmp
 	@$(MKCONFIG) -n $@ -a TQM5200 powerpc mpc5xxx tqm5200 tqc
 
 uc101_config:		unconfig
@@ -807,7 +750,7 @@ mpc5121ads_rev2_config	\
 	@if [ "$(findstring rev2,$@)" ] ; then \
 		echo "#define CONFIG_ADS5121_REV2 1" > $(obj)include/config.h; \
 	fi
-	@$(MKCONFIG) -a mpc5121ads powerpc mpc512x mpc5121ads freescale
+	@$(MKCONFIG) -n $@ -a mpc5121ads powerpc mpc512x mpc5121ads freescale
 
 pdm360ng_config:	unconfig
 	@$(MKCONFIG) -a pdm360ng powerpc mpc512x pdm360ng
@@ -816,17 +759,15 @@ pdm360ng_config:	unconfig
 ## MPC8xx Systems
 #########################################################################
 
-Adder_config	\
 Adder87x_config \
 AdderII_config	\
+AdderUSB_config	\
+Adder_config	\
 	:		unconfig
 	@mkdir -p $(obj)include
 	$(if $(findstring AdderII,$@), \
-	@echo "#define CONFIG_MPC852T" > $(obj)include/config.h)
-	@$(MKCONFIG) -a Adder powerpc mpc8xx adder
-
-AdderUSB_config:	unconfig
-	@$(MKCONFIG) -a AdderUSB powerpc mpc8xx adder
+		@echo "#define CONFIG_MPC852T" > $(obj)include/config.h)
+	@$(MKCONFIG) -n $@ -a Adder powerpc mpc8xx adder
 
 ADS860_config	  \
 FADS823_config	  \
@@ -834,7 +775,7 @@ FADS850SAR_config \
 MPC86xADS_config  \
 MPC885ADS_config  \
 FADS860T_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx fads
+	@$(MKCONFIG) -n $@ $(@:_config=) powerpc mpc8xx fads
 
 AMX860_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx amx860 westel
@@ -869,10 +810,8 @@ GEN860T_SC_config	\
 GEN860T_config: unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring _SC,$@)" ] || \
-		{ echo "#define CONFIG_SC" >>$(obj)include/config.h ; \
-		  $(XECHO) "With reduced H/W feature set (SC)..." ; \
-		}
-	@$(MKCONFIG) -a $(call xtract_GEN860T,$@) powerpc mpc8xx gen860t
+		echo "#define CONFIG_SC" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_GEN860T,$@) powerpc mpc8xx gen860t
 
 GENIETV_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx genietv
@@ -895,10 +834,8 @@ ICU862_100MHz_config	\
 ICU862_config: unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring _100MHz,$@)" ] || \
-		{ echo "#define CONFIG_100MHz"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with 100MHz system clock" ; \
-		}
-	@$(MKCONFIG) -a $(call xtract_ICU862,$@) powerpc mpc8xx icu862
+		echo "#define CONFIG_100MHz" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_ICU862,$@) powerpc mpc8xx icu862
 
 IP860_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx ip860
@@ -908,30 +845,24 @@ IVML24_128_config \
 IVML24_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring IVML24_config,$@)" ] || \
-		 { echo "#define CONFIG_IVML24_16M"	>>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_IVML24_16M" >>$(obj)include/config.h
 	@[ -z "$(findstring IVML24_128_config,$@)" ] || \
-		 { echo "#define CONFIG_IVML24_32M"	>>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_IVML24_32M" >>$(obj)include/config.h
 	@[ -z "$(findstring IVML24_256_config,$@)" ] || \
-		 { echo "#define CONFIG_IVML24_64M"	>>$(obj)include/config.h ; \
-		 }
-	@$(MKCONFIG) -a IVML24 powerpc mpc8xx ivm
+		echo "#define CONFIG_IVML24_64M" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a IVML24 powerpc mpc8xx ivm
 
 IVMS8_256_config \
 IVMS8_128_config \
 IVMS8_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring IVMS8_config,$@)" ] || \
-		 { echo "#define CONFIG_IVMS8_16M"	>>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_IVMS8_16M"	>>$(obj)include/config.h
 	@[ -z "$(findstring IVMS8_128_config,$@)" ] || \
-		 { echo "#define CONFIG_IVMS8_32M"	>>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_IVMS8_32M"	>>$(obj)include/config.h
 	@[ -z "$(findstring IVMS8_256_config,$@)" ] || \
-		 { echo "#define CONFIG_IVMS8_64M"	>>$(obj)include/config.h ; \
-		 }
-	@$(MKCONFIG) -a IVMS8 powerpc mpc8xx ivm
+		echo "#define CONFIG_IVMS8_64M"	>>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a IVMS8 powerpc mpc8xx ivm
 
 kmsupx4_config:		unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx km8xx keymile
@@ -950,7 +881,7 @@ lwmon_config:		unconfig
 
 MBX_config	\
 MBX860T_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx mbx8xx
+	@$(MKCONFIG) -n $@ $(@:_config=) powerpc mpc8xx mbx8xx
 
 mgsuvd_config:		unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx km8xx keymile
@@ -964,14 +895,10 @@ NETVIA_V2_config \
 NETVIA_config:		unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring NETVIA_config,$@)" ] || \
-		 { echo "#define CONFIG_NETVIA_VERSION 1" >>$(obj)include/config.h ; \
-		  $(XECHO) "... Version 1" ; \
-		 }
+		echo "#define CONFIG_NETVIA_VERSION 1" >>$(obj)include/config.h
 	@[ -z "$(findstring NETVIA_V2_config,$@)" ] || \
-		 { echo "#define CONFIG_NETVIA_VERSION 2" >>$(obj)include/config.h ; \
-		  $(XECHO) "... Version 2" ; \
-		 }
-	@$(MKCONFIG) -a $(call xtract_NETVIA,$@) powerpc mpc8xx netvia
+		echo "#define CONFIG_NETVIA_VERSION 2" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_NETVIA,$@) powerpc mpc8xx netvia
 
 xtract_NETPHONE = $(subst _V2,,$(subst _config,,$1))
 
@@ -979,12 +906,10 @@ NETPHONE_V2_config \
 NETPHONE_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring NETPHONE_config,$@)" ] || \
-		 { echo "#define CONFIG_NETPHONE_VERSION 1" >>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_NETPHONE_VERSION 1" >>$(obj)include/config.h
 	@[ -z "$(findstring NETPHONE_V2_config,$@)" ] || \
-		 { echo "#define CONFIG_NETPHONE_VERSION 2" >>$(obj)include/config.h ; \
-		 }
-	@$(MKCONFIG) -a $(call xtract_NETPHONE,$@) powerpc mpc8xx netphone
+		echo "#define CONFIG_NETPHONE_VERSION 2" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_NETPHONE,$@) powerpc mpc8xx netphone
 
 xtract_NETTA = $(subst _SWAPHOOK,,$(subst _6412,,$(subst _ISDN,,$(subst _config,,$1))))
 
@@ -998,24 +923,18 @@ NETTA_6412_config \
 NETTA_config:		unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring ISDN_,$@)" ] || \
-		 { echo "#define CONFIG_NETTA_ISDN 1" >>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_NETTA_ISDN 1" >>$(obj)include/config.h
 	@[ -n "$(findstring ISDN_,$@)" ] || \
-		 { echo "#undef CONFIG_NETTA_ISDN" >>$(obj)include/config.h ; \
-		 }
+		echo "#undef CONFIG_NETTA_ISDN" >>$(obj)include/config.h
 	@[ -z "$(findstring 6412_,$@)" ] || \
-		 { echo "#define CONFIG_NETTA_6412 1" >>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_NETTA_6412 1" >>$(obj)include/config.h
 	@[ -n "$(findstring 6412_,$@)" ] || \
-		 { echo "#undef CONFIG_NETTA_6412" >>$(obj)include/config.h ; \
-		 }
+		echo "#undef CONFIG_NETTA_6412" >>$(obj)include/config.h
 	@[ -z "$(findstring SWAPHOOK_,$@)" ] || \
-		 { echo "#define CONFIG_NETTA_SWAPHOOK 1" >>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_NETTA_SWAPHOOK 1" >>$(obj)include/config.h
 	@[ -n "$(findstring SWAPHOOK_,$@)" ] || \
-		 { echo "#undef CONFIG_NETTA_SWAPHOOK" >>$(obj)include/config.h ; \
-		 }
-	@$(MKCONFIG) -a $(call xtract_NETTA,$@) powerpc mpc8xx netta
+		echo "#undef CONFIG_NETTA_SWAPHOOK" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_NETTA,$@) powerpc mpc8xx netta
 
 xtract_NETTA2 = $(subst _V2,,$(subst _config,,$1))
 
@@ -1023,28 +942,26 @@ NETTA2_V2_config \
 NETTA2_config:		unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring NETTA2_config,$@)" ] || \
-		 { echo "#define CONFIG_NETTA2_VERSION 1" >>$(obj)include/config.h ; \
-		 }
+		echo "#define CONFIG_NETTA2_VERSION 1" >>$(obj)include/config.h
 	@[ -z "$(findstring NETTA2_V2_config,$@)" ] || \
-		 { echo "#define CONFIG_NETTA2_VERSION 2" >>$(obj)include/config.h ; \
-		 }
-	@$(MKCONFIG) -a $(call xtract_NETTA2,$@) powerpc mpc8xx netta2
+		echo "#define CONFIG_NETTA2_VERSION 2" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_NETTA2,$@) powerpc mpc8xx netta2
 
 NC650_Rev1_config \
 NC650_Rev2_config \
 CP850_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring CP850,$@)" ] || \
-		 { echo "#define CONFIG_CP850 1" >>$(obj)include/config.h ; \
-		   echo "#define CONFIG_IDS852_REV2 1" >>$(obj)include/config.h ; \
-		 }
+		{ echo "#define CONFIG_CP850 1" >>$(obj)include/config.h ; \
+		  echo "#define CONFIG_IDS852_REV2 1" >>$(obj)include/config.h ; \
+		}
 	@[ -z "$(findstring Rev1,$@)" ] || \
-		 { echo "#define CONFIG_IDS852_REV1 1" >>$(obj)include/config.h ; \
-		 }
+		{ echo "#define CONFIG_IDS852_REV1 1" >>$(obj)include/config.h ; \
+		}
 	@[ -z "$(findstring Rev2,$@)" ] || \
-		 { echo "#define CONFIG_IDS852_REV2 1" >>$(obj)include/config.h ; \
-		 }
-	@$(MKCONFIG) -a NC650 powerpc mpc8xx nc650
+		{ echo "#define CONFIG_IDS852_REV2 1" >>$(obj)include/config.h ; \
+		}
+	@$(MKCONFIG) -n $@ -a NC650 powerpc mpc8xx nc650
 
 NX823_config:		unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx nx823
@@ -1086,19 +1003,14 @@ RPXlite_DW_NVRAM_64_LCD_config	\
 RPXlite_DW_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring _64,$@)" ] || \
-		{ echo "#define RPXlite_64MHz"		>>$(obj)include/config.h ; \
-		  $(XECHO) "... with 64MHz system clock ..."; \
-		}
+		echo "#define RPXlite_64MHz"		>>$(obj)include/config.h
 	@[ -z "$(findstring _LCD,$@)" ] || \
 		{ echo "#define CONFIG_LCD"		>>$(obj)include/config.h ; \
 		  echo "#define CONFIG_NEC_NL6448BC20"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with LCD display ..."; \
 		}
 	@[ -z "$(findstring _NVRAM,$@)" ] || \
-		{ echo "#define  CONFIG_ENV_IS_IN_NVRAM"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with ENV in NVRAM ..."; \
-		}
-	@$(MKCONFIG) -a RPXlite_DW powerpc mpc8xx RPXlite_dw
+		echo "#define  CONFIG_ENV_IS_IN_NVRAM"	>>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a RPXlite_DW powerpc mpc8xx RPXlite_dw
 
 rmu_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx rmu
@@ -1161,9 +1073,8 @@ virtlab2_config:	unconfig
 	@[ -z "$(findstring _LCD,$@)" ] || \
 		{ echo "#define CONFIG_LCD"		>>$(obj)include/config.h ; \
 		  echo "#define CONFIG_NEC_NL6448BC20"	>>$(obj)include/config.h ; \
-		  $(XECHO) "... with LCD display" ; \
 		}
-	@$(MKCONFIG) -a $(call xtract_8xx,$@) powerpc mpc8xx tqm8xx tqc
+	@$(MKCONFIG) -n $@ -a $(call xtract_8xx,$@) powerpc mpc8xx tqm8xx tqc
 
 TTTech_config:	unconfig
 	@mkdir -p $(obj)include
@@ -1253,25 +1164,21 @@ glacier_nand_config:	unconfig
 	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
 	@echo "#define CONFIG_$$(echo $(subst ,,$(@:_nand_config=)) | \
 		tr '[:lower:]' '[:upper:]')" >> $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a canyonlands powerpc ppc4xx canyonlands amcc
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/canyonlands/config.tmp
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) -n $@ -a canyonlands powerpc ppc4xx canyonlands amcc
 
 CATcenter_config	\
 CATcenter_25_config	\
 CATcenter_33_config:	unconfig
 	@mkdir -p $(obj)include
-	@ echo "/* CATcenter uses PPChameleon Model ME */"  > $(obj)include/config.h
-	@ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 1" >> $(obj)include/config.h
+	@echo "/* CATcenter uses PPChameleon Model ME */"  > $(obj)include/config.h
+	@echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 1" >> $(obj)include/config.h
 	@[ -z "$(findstring _25,$@)" ] || \
-		{ echo "#define CONFIG_PPCHAMELEON_CLK_25" >> $(obj)include/config.h ; \
-		  $(XECHO) "SysClk = 25MHz" ; \
-		}
+		echo "#define CONFIG_PPCHAMELEON_CLK_25" >> $(obj)include/config.h
 	@[ -z "$(findstring _33,$@)" ] || \
-		{ echo "#define CONFIG_PPCHAMELEON_CLK_33" >> $(obj)include/config.h ; \
-		  $(XECHO) "SysClk = 33MHz" ; \
-		}
-	@$(MKCONFIG) -a $(call xtract_4xx,$@) powerpc ppc4xx PPChameleonEVB dave
+		echo "#define CONFIG_PPCHAMELEON_CLK_33" >> $(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_4xx,$@) powerpc ppc4xx PPChameleonEVB dave
 
 CMS700_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx cms700 esd
@@ -1284,7 +1191,7 @@ CPCI4052_config		\
 CPCI405DT_config	\
 CPCI405AB_config:	unconfig
 	@mkdir -p $(obj)board/esd/cpci405
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx cpci405 esd
+	@$(MKCONFIG) -n $@ $(@:_config=) powerpc ppc4xx cpci405 esd
 
 CPCIISER4_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx cpciiser4 esd
@@ -1387,9 +1294,9 @@ haleakala_nand_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/amcc/kilauea
 	@mkdir -p $(obj)nand_spl/board/amcc/kilauea
 	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a kilauea powerpc ppc4xx kilauea amcc
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/kilauea/config.tmp
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) -n $@ -a kilauea powerpc ppc4xx kilauea amcc
 
 korat_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx korat
@@ -1448,7 +1355,7 @@ ocotea_config:	unconfig
 
 OCRTC_config		\
 ORSG_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx ocrtc esd
+	@$(MKCONFIG) -n $@ $(@:_config=) powerpc ppc4xx ocrtc esd
 
 p3p440_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx p3p440 prodrive
@@ -1483,26 +1390,16 @@ PPChameleonEVB_ME_33_config	\
 PPChameleonEVB_HI_33_config:	unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring EVB_BA,$@)" ] || \
-		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 0" >>$(obj)include/config.h ; \
-		  $(XECHO) "... BASIC model" ; \
-		}
+		echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 0" >>$(obj)include/config.h
 	@[ -z "$(findstring EVB_ME,$@)" ] || \
-		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 1" >>$(obj)include/config.h ; \
-		  $(XECHO) "... MEDIUM model" ; \
-		}
+		echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 1" >>$(obj)include/config.h
 	@[ -z "$(findstring EVB_HI,$@)" ] || \
-		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 2" >>$(obj)include/config.h ; \
-		  $(XECHO) "... HIGH-END model" ; \
-		}
+		echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 2" >>$(obj)include/config.h
 	@[ -z "$(findstring _25,$@)" ] || \
-		{ echo "#define CONFIG_PPCHAMELEON_CLK_25" >>$(obj)include/config.h ; \
-		  $(XECHO) "SysClk = 25MHz" ; \
-		}
+		echo "#define CONFIG_PPCHAMELEON_CLK_25" >>$(obj)include/config.h
 	@[ -z "$(findstring _33,$@)" ] || \
-		{ echo "#define CONFIG_PPCHAMELEON_CLK_33" >>$(obj)include/config.h ; \
-		  $(XECHO) "SysClk = 33MHz" ; \
-		}
-	@$(MKCONFIG) -a $(call xtract_4xx,$@) powerpc ppc4xx PPChameleonEVB dave
+		echo "#define CONFIG_PPCHAMELEON_CLK_33" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a $(call xtract_4xx,$@) powerpc ppc4xx PPChameleonEVB dave
 
 quad100hd_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx quad100hd
@@ -1530,9 +1427,9 @@ rainier_nand_config: unconfig
 	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
 	@echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
 		tr '[:lower:]' '[:upper:]')" >> $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a sequoia powerpc ppc4xx sequoia amcc
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) -n $@ -a sequoia powerpc ppc4xx sequoia amcc
 
 sequoia_ramboot_config \
 rainier_ramboot_config: unconfig
@@ -1540,10 +1437,10 @@ rainier_ramboot_config: unconfig
 	@echo "#define CONFIG_SYS_RAMBOOT" > $(obj)include/config.h
 	@echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
 		tr '[:lower:]' '[:upper:]')" >> $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a sequoia powerpc ppc4xx sequoia amcc
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
 	@echo "LDSCRIPT = board/amcc/sequoia/u-boot-ram.lds" >> \
 		$(obj)board/amcc/sequoia/config.tmp
+	@$(MKCONFIG) -n $@ -a sequoia powerpc ppc4xx sequoia amcc
 
 taihu_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx taihu amcc
@@ -1577,7 +1474,7 @@ VOM405_config:	unconfig
 
 W7OLMC_config	\
 W7OLMG_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx w7o
+	@$(MKCONFIG) -n $@ $(@:_config=) powerpc ppc4xx w7o
 
 # Walnut & Sycamore images are identical (recognized via PVR)
 walnut_config \
@@ -1641,7 +1538,7 @@ zeus_config:	unconfig
 
 Alaska8220_config	\
 Yukon8220_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8220 alaska
+	@$(MKCONFIG) -n $@ $(@:_config=) powerpc mpc8220 alaska
 
 sorcery_config:		unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8220 sorcery
@@ -1662,16 +1559,14 @@ BMW_config: unconfig
 
 CPC45_config	\
 CPC45_ROMBOOT_config:	unconfig
-	@$(MKCONFIG) $(call xtract_82xx,$@) powerpc mpc824x cpc45
-	@cd $(obj)include ;				\
+	@mkdir -p $(obj)include ;				\
 	if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
-		echo "CONFIG_BOOT_ROM = y" >> config.mk ; \
-		$(XECHO) "... booting from 8-bit flash" ; \
+		echo "CONFIG_BOOT_ROM = y" >> $(obj)include/config.mk ; \
 	else \
-		echo "CONFIG_BOOT_ROM = n" >> config.mk ; \
-		$(XECHO) "... booting from 64-bit flash" ; \
+		echo "CONFIG_BOOT_ROM = n" >> $(obj)include/config.mk ; \
 	fi; \
-	echo "export CONFIG_BOOT_ROM" >> config.mk;
+	echo "export CONFIG_BOOT_ROM" >> $(obj)include/config.mk;
+	@$(MKCONFIG) -n $@ $(call xtract_82xx,$@) powerpc mpc824x cpc45
 
 CU824_config: unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc824x cu824
@@ -1739,33 +1634,29 @@ cogent_mpc8260_config:	unconfig
 
 CPU86_config	\
 CPU86_ROMBOOT_config: unconfig
-	@$(MKCONFIG) $(call xtract_82xx,$@) powerpc mpc8260 cpu86
-	@cd $(obj)include ;				\
+	@mkdir -p  $(obj)include ;				\
 	if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
-		echo "CONFIG_BOOT_ROM = y" >> config.mk ; \
-		$(XECHO) "... booting from 8-bit flash" ; \
+		echo "CONFIG_BOOT_ROM = y" >> $(obj)include/config.mk ; \
 	else \
-		echo "CONFIG_BOOT_ROM = n" >> config.mk ; \
-		$(XECHO) "... booting from 64-bit flash" ; \
+		echo "CONFIG_BOOT_ROM = n" >> $(obj)include/config.mk ; \
 	fi; \
-	echo "export CONFIG_BOOT_ROM" >> config.mk;
+	echo "export CONFIG_BOOT_ROM" >> $(obj)include/config.mk;
+	@$(MKCONFIG) -n $@ $(call xtract_82xx,$@) powerpc mpc8260 cpu86
 
 CPU87_config	\
 CPU87_ROMBOOT_config: unconfig
-	@$(MKCONFIG) $(call xtract_82xx,$@) powerpc mpc8260 cpu87
-	@cd $(obj)include ;				\
+	@mkdir -p $(obj)include ;				\
 	if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
-		echo "CONFIG_BOOT_ROM = y" >> config.mk ; \
-		$(XECHO) "... booting from 8-bit flash" ; \
+		echo "CONFIG_BOOT_ROM = y" >> $(obj)include/config.mk ; \
 	else \
-		echo "CONFIG_BOOT_ROM = n" >> config.mk ; \
-		$(XECHO) "... booting from 64-bit flash" ; \
+		echo "CONFIG_BOOT_ROM = n" >> $(obj)include/config.mk ; \
 	fi; \
-	echo "export CONFIG_BOOT_ROM" >> config.mk;
+	echo "export CONFIG_BOOT_ROM" >> $(obj)include/config.mk;
+	@$(MKCONFIG) -n $@ $(call xtract_82xx,$@) powerpc mpc8260 cpu87
 
 ep8248_config	\
 ep8248E_config	:	unconfig
-	@$(MKCONFIG) ep8248 powerpc mpc8260 ep8248
+	@$(MKCONFIG) -n $@ ep8248 powerpc mpc8260 ep8248
 
 ep8260_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 ep8260
@@ -1791,7 +1682,7 @@ ISPAN_REVB_config:	unconfig
 	@if [ "$(findstring _REVB_,$@)" ] ; then \
 		echo "#define CONFIG_SYS_REV_B" > $(obj)include/config.h ; \
 	fi
-	@$(MKCONFIG) -a ISPAN powerpc mpc8260 ispan
+	@$(MKCONFIG) -n $@ -a ISPAN powerpc mpc8260 ispan
 
 mgcoge_config	:	unconfig
 	@$(MKCONFIG) mgcoge powerpc mpc8260 mgcoge keymile
@@ -1823,10 +1714,8 @@ PQ2FADS-ZU_66MHz_lowboot_config	\
 	$(if $(findstring VR,$@), \
 	@echo "#define CONFIG_8260_CLKIN 66000000" >> $(obj)include/config.h))
 	@[ -z "$(findstring lowboot_,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFF800000" >$(obj)board/freescale/mpc8260ads/config.tmp ; \
-		  $(XECHO) "... with lowboot configuration" ; \
-		}
-	@$(MKCONFIG) -a MPC8260ADS powerpc mpc8260 mpc8260ads freescale
+		echo "TEXT_BASE = 0xFF800000" >$(obj)board/freescale/mpc8260ads/config.tmp
+	@$(MKCONFIG) -n $@ -a MPC8260ADS powerpc mpc8260 mpc8260ads freescale
 
 MPC8266ADS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 mpc8266ads freescale
@@ -1838,7 +1727,7 @@ muas3001_config	:	unconfig
 	@if [ "$(findstring dev,$@)" ] ; then \
 		echo "#define CONFIG_MUAS_DEV_BOARD" > $(obj)include/config.h ; \
 	fi
-	@$(MKCONFIG) -a muas3001 powerpc mpc8260 muas3001
+	@$(MKCONFIG) -n $@ -a muas3001 powerpc mpc8260 muas3001
 
 # PM825/PM826 default configuration:  small (= 8 MB) Flash / boot from 64-bit flash
 PM825_config	\
@@ -1857,15 +1746,12 @@ PM826_ROMBOOT_BIGFLASH_config:	unconfig
 		>$(obj)include/config.h ; \
 	fi
 	@if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
-		$(XECHO) "... booting from 8-bit flash" ; \
 		echo "#define CONFIG_BOOT_ROM" >>$(obj)include/config.h ; \
 		echo "TEXT_BASE = 0xFF800000" >$(obj)board/pm826/config.tmp ; \
 		if [ "$(findstring _BIGFLASH_,$@)" ] ; then \
-			$(XECHO) "... with 32 MB Flash" ; \
 			echo "#define CONFIG_FLASH_32MB" >>$(obj)include/config.h ; \
 		fi; \
 	else \
-		$(XECHO) "... booting from 64-bit flash" ; \
 		if [ "$(findstring _BIGFLASH_,$@)" ] ; then \
 			$(XECHO) "... with 32 MB Flash" ; \
 			echo "#define CONFIG_FLASH_32MB" >>$(obj)include/config.h ; \
@@ -1874,7 +1760,7 @@ PM826_ROMBOOT_BIGFLASH_config:	unconfig
 			echo "TEXT_BASE = 0xFF000000" >$(obj)board/pm826/config.tmp ; \
 		fi; \
 	fi
-	@$(MKCONFIG) -a PM826 powerpc mpc8260 pm826
+	@$(MKCONFIG) -n $@ -a PM826 powerpc mpc8260 pm826
 
 PM828_config	\
 PM828_PCI_config	\
@@ -1884,14 +1770,12 @@ PM828_ROMBOOT_PCI_config:	unconfig
 	@mkdir -p $(obj)board/pm826
 	@if [ "$(findstring _PCI_,$@)" ] ; then \
 		echo "#define CONFIG_PCI"  >>$(obj)include/config.h ; \
-		$(XECHO) "... with PCI enabled" ; \
 	fi
 	@if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
-		$(XECHO) "... booting from 8-bit flash" ; \
 		echo "#define CONFIG_BOOT_ROM" >>$(obj)include/config.h ; \
 		echo "TEXT_BASE = 0xFF800000" >$(obj)board/pm826/config.tmp ; \
 	fi
-	@$(MKCONFIG) -a PM828 powerpc mpc8260 pm828
+	@$(MKCONFIG) -n $@ -a PM828 powerpc mpc8260 pm828
 
 ppmc8260_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 ppmc8260
@@ -1900,8 +1784,8 @@ Rattler8248_config	\
 Rattler_config:		unconfig
 	@mkdir -p $(obj)include
 	$(if $(findstring 8248,$@), \
-	@echo "#define CONFIG_MPC8248" > $(obj)include/config.h)
-	@$(MKCONFIG) -a Rattler powerpc mpc8260 rattler
+		@echo "#define CONFIG_MPC8248" > $(obj)include/config.h)
+	@$(MKCONFIG) -n $@ -a Rattler powerpc mpc8260 rattler
 
 RPXsuper_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 rpxsuper
@@ -1947,22 +1831,17 @@ TQM8265_AA_config:  unconfig
 		echo "#define CONFIG_$${CTYPE}"	>>$(obj)include/config.h ; \
 	fi; \
 	echo "#define CONFIG_$${CFREQ}MHz"	>>$(obj)include/config.h ; \
-	echo "... with $${CFREQ}MHz system clock" ; \
 	if [ "$${CACHE}" = "yes" ] ; then \
 		echo "#define CONFIG_L2_CACHE"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with L2 Cache support" ; \
 	else \
 		echo "#undef CONFIG_L2_CACHE"	>>$(obj)include/config.h ; \
-		$(XECHO) "... without L2 Cache support" ; \
 	fi; \
 	if [ "$${BMODE}" = "60x" ] ; then \
 		echo "#define CONFIG_BUSMODE_60x" >>$(obj)include/config.h ; \
-		$(XECHO) "... with 60x Bus Mode" ; \
 	else \
 		echo "#undef CONFIG_BUSMODE_60x"  >>$(obj)include/config.h ; \
-		$(XECHO) "... without 60x Bus Mode" ; \
 	fi
-	@$(MKCONFIG) -a TQM8260 powerpc mpc8260 tqm8260 tqc
+	@$(MKCONFIG) -n $@ -a TQM8260 powerpc mpc8260 tqm8260 tqc
 
 TQM8272_config: unconfig
 	@$(MKCONFIG) TQM8272 powerpc mpc8260 tqm8272 tqc
@@ -1971,7 +1850,7 @@ VoVPN-GW_66MHz_config	\
 VoVPN-GW_100MHz_config:		unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_CLKIN_$(word 2,$(subst _, ,$@))" > $(obj)include/config.h
-	@$(MKCONFIG) -a VoVPN-GW powerpc mpc8260 vovpn-gw funkwerk
+	@$(MKCONFIG) -n $@ -a VoVPN-GW powerpc mpc8260 vovpn-gw funkwerk
 
 ZPC1900_config: unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 zpc1900
@@ -1982,7 +1861,7 @@ ZPC1900_config: unconfig
 
 astro_mcf5373l_config \
 astro_mcf5373l_RAM_config :	unconfig
-	@$(MKCONFIG) -t $(@:_config=) astro_mcf5373l m68k mcf532x mcf5373l astro
+	@$(MKCONFIG) -n $@ -t $(@:_config=) astro_mcf5373l m68k mcf532x mcf5373l astro
 
 M5208EVBE_config :		unconfig
 	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5208evbe freescale
@@ -1999,16 +1878,14 @@ M52277EVB_stmicro_config :	unconfig
 		echo "#define CONFIG_SYS_SPANSION_BOOT"	>> $(obj)include/config.h ; \
 		echo "TEXT_BASE = 0x00000000" > $(obj)board/freescale/m52277evb/config.tmp ; \
 		cp $(obj)board/freescale/m52277evb/u-boot.spa $(obj)board/freescale/m52277evb/u-boot.lds ; \
-		$(XECHO) "... with SPANSION boot..." ; \
 	fi; \
 	if [ "$${FLASH}" = "STMICRO" ] ; then \
 		echo "#define CONFIG_CF_SBF"	>> $(obj)include/config.h ; \
 		echo "#define CONFIG_SYS_STMICRO_BOOT"	>> $(obj)include/config.h ; \
 		echo "TEXT_BASE = 0x43E00000" > $(obj)board/freescale/m52277evb/config.tmp ; \
 		cp $(obj)board/freescale/m52277evb/u-boot.stm $(obj)board/freescale/m52277evb/u-boot.lds ; \
-		$(XECHO) "... with ST Micro boot..." ; \
 	fi
-	@$(MKCONFIG) -a M52277EVB m68k mcf5227x m52277evb freescale
+	@$(MKCONFIG) -n $@ -a M52277EVB m68k mcf5227x m52277evb freescale
 
 M5235EVB_config \
 M5235EVB_Flash16_config \
@@ -2026,7 +1903,7 @@ M5235EVB_Flash32_config:	unconfig
 		echo "TEXT_BASE = 0xFFE00000" > $(obj)board/freescale/m5235evb/config.tmp ; \
 		cp $(obj)board/freescale/m5235evb/u-boot.16 $(obj)board/freescale/m5235evb/u-boot.lds ; \
 	fi
-	@$(MKCONFIG) -a M5235EVB m68k mcf523x m5235evb freescale
+	@$(MKCONFIG) -n $@ -a M5235EVB m68k mcf523x m5235evb freescale
 
 M5249EVB_config :		unconfig
 	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5249evb freescale
@@ -2044,13 +1921,13 @@ EB+MCF-EV123_config :		unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/BuS/EB+MCF-EV123
 	@echo "TEXT_BASE = 0xFFE00000"|tee $(obj)board/BuS/EB+MCF-EV123/textbase.mk
-	@$(MKCONFIG) EB+MCF-EV123 m68k mcf52x2 EB+MCF-EV123 BuS
+	@$(MKCONFIG) -n $@ EB+MCF-EV123 m68k mcf52x2 EB+MCF-EV123 BuS
 
 EB+MCF-EV123_internal_config :	unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/BuS/EB+MCF-EV123
 	@echo "TEXT_BASE = 0xF0000000"|tee $(obj)board/BuS/EB+MCF-EV123/textbase.mk
-	@$(MKCONFIG) EB+MCF-EV123 m68k mcf52x2 EB+MCF-EV123 BuS
+	@$(MKCONFIG) -n $@ EB+MCF-EV123 m68k mcf52x2 EB+MCF-EV123 BuS
 
 EP2500_config:			unconfig
 	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 ep2500 Mercury
@@ -2082,7 +1959,7 @@ M5329BFEE_config :	unconfig
 	if [ "$${NAND}" != "0" ] ; then \
 		echo "#define NANDFLASH_SIZE	$${NAND}" > $(obj)include/config.h ; \
 	fi
-	@$(MKCONFIG) -a M5329EVB m68k mcf532x m5329evb freescale
+	@$(MKCONFIG) -n $@ -a M5329EVB m68k mcf532x m5329evb freescale
 
 M5373EVB_config :	unconfig
 	@case "$@" in \
@@ -2102,17 +1979,15 @@ M54451EVB_stmicro_config :	unconfig
 	if [ "$${FLASH}" = "NOR" ] ; then \
 		echo "TEXT_BASE = 0x00000000" > $(obj)board/freescale/m54451evb/config.tmp ; \
 		cp $(obj)board/freescale/m54451evb/u-boot.spa $(obj)board/freescale/m54451evb/u-boot.lds ; \
-		$(XECHO) "... with NOR boot..." ; \
 	fi; \
 	if [ "$${FLASH}" = "STMICRO" ] ; then \
 		echo "#define CONFIG_CF_SBF"	>> $(obj)include/config.h ; \
 		echo "#define CONFIG_SYS_STMICRO_BOOT"	>> $(obj)include/config.h ; \
 		echo "TEXT_BASE = 0x47E00000" > $(obj)board/freescale/m54451evb/config.tmp ; \
 		cp $(obj)board/freescale/m54451evb/u-boot.stm $(obj)board/freescale/m54451evb/u-boot.lds ; \
-		$(XECHO) "... with ST Micro boot..." ; \
 	fi; \
 	echo "#define CONFIG_SYS_INPUT_CLKSRC 24000000" >> $(obj)include/config.h ;
-	@$(MKCONFIG) -a M54451EVB m68k mcf5445x m54451evb freescale
+	@$(MKCONFIG) -n $@ -a M54451EVB m68k mcf5445x m54451evb freescale
 
 M54455EVB_config \
 M54455EVB_atmel_config \
@@ -2136,24 +2011,20 @@ M54455EVB_stm33_config :	unconfig
 		echo "#define CONFIG_SYS_INTEL_BOOT" >> $(obj)include/config.h ; \
 		echo "TEXT_BASE = 0x00000000" > $(obj)board/freescale/m54455evb/config.tmp ; \
 		cp $(obj)board/freescale/m54455evb/u-boot.int $(obj)board/freescale/m54455evb/u-boot.lds ; \
-		$(XECHO) "... with INTEL boot..." ; \
 	fi; \
 	if [ "$${FLASH}" = "ATMEL" ] ; then \
 		echo "#define CONFIG_SYS_ATMEL_BOOT"	>> $(obj)include/config.h ; \
 		echo "TEXT_BASE = 0x04000000" > $(obj)board/freescale/m54455evb/config.tmp ; \
 		cp $(obj)board/freescale/m54455evb/u-boot.atm $(obj)board/freescale/m54455evb/u-boot.lds ; \
-		$(XECHO) "... with ATMEL boot..." ; \
 	fi; \
 	if [ "$${FLASH}" = "STMICRO" ] ; then \
 		echo "#define CONFIG_CF_SBF"	>> $(obj)include/config.h ; \
 		echo "#define CONFIG_SYS_STMICRO_BOOT"	>> $(obj)include/config.h ; \
 		echo "TEXT_BASE = 0x4FE00000" > $(obj)board/freescale/m54455evb/config.tmp ; \
 		cp $(obj)board/freescale/m54455evb/u-boot.stm $(obj)board/freescale/m54455evb/u-boot.lds ; \
-		$(XECHO) "... with ST Micro boot..." ; \
 	fi; \
 	echo "#define CONFIG_SYS_INPUT_CLKSRC $${FREQ}" >> $(obj)include/config.h ; \
-	$(XECHO) "... with $${FREQ}Hz input clock"
-	@$(MKCONFIG) -a M54455EVB m68k mcf5445x m54455evb freescale
+	@$(MKCONFIG) -n $@ -a M54455EVB m68k mcf5445x m54455evb freescale
 
 M5475AFE_config \
 M5475BFE_config \
@@ -2186,7 +2057,7 @@ M5475GFE_config :	unconfig
 	if [ "$${USB}" == "1" ] ; then \
 		echo "#define CONFIG_SYS_USBCTRL" >> $(obj)include/config.h ; \
 	fi
-	@$(MKCONFIG) -a M5475EVB m68k mcf547x_8x m547xevb freescale
+	@$(MKCONFIG) -n $@ -a M5475EVB m68k mcf547x_8x m547xevb freescale
 
 M5485AFE_config \
 M5485BFE_config \
@@ -2221,7 +2092,7 @@ M5485HFE_config :	unconfig
 	if [ "$${USB}" == "1" ] ; then \
 		echo "#define CONFIG_SYS_USBCTRL" >> $(obj)include/config.h ; \
 	fi
-	@$(MKCONFIG) -a M5485EVB m68k mcf547x_8x m548xevb freescale
+	@$(MKCONFIG) -n $@ -a M5485EVB m68k mcf547x_8x m548xevb freescale
 
 TASREG_config :		unconfig
 	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 tasreg esd
@@ -2240,26 +2111,23 @@ MPC8313ERDB_NAND_66_config: unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/freescale/mpc8313erdb
 	@if [ "$(findstring _33_,$@)" ] ; then \
-		$(XECHO) -n "...33M ..." ; \
 		echo "#define CONFIG_SYS_33MHZ" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _66_,$@)" ] ; then \
-		$(XECHO) -n "...66M..." ; \
 		echo "#define CONFIG_SYS_66MHZ" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _NAND_,$@)" ] ; then \
-		$(XECHO) -n "...NAND..." ; \
 		echo "TEXT_BASE = 0x00100000" > $(obj)board/freescale/mpc8313erdb/config.tmp ; \
 		echo "#define CONFIG_NAND_U_BOOT" >>$(obj)include/config.h ; \
 	fi ;
-	@$(MKCONFIG) -a MPC8313ERDB powerpc mpc83xx mpc8313erdb freescale
 	@if [ "$(findstring _NAND_,$@)" ] ; then \
 		echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk ; \
 	fi ;
+	@$(MKCONFIG) -n $@ -a MPC8313ERDB powerpc mpc83xx mpc8313erdb freescale
 
 MPC8315ERDB_NAND_config \
 MPC8315ERDB_config: unconfig
-	@$(MKCONFIG) -t $(@:_config=) MPC8315ERDB powerpc mpc83xx mpc8315erdb freescale
+	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8315ERDB powerpc mpc83xx mpc8315erdb freescale
 
 MPC8323ERDB_config:	unconfig
 	@$(MKCONFIG) -a MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale
@@ -2271,30 +2139,25 @@ MPC832XEMDS_SLAVE_config \
 MPC832XEMDS_ATM_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _HOST_,$@)" ] ; then \
-		$(XECHO) -n "... PCI HOST " ; \
 		echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _SLAVE_,$@)" ] ; then \
-		$(XECHO) "...PCI SLAVE 66M"  ; \
 		echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PCISLAVE" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _33_,$@)" ] ; then \
-		$(XECHO) -n "...33M ..." ; \
 		echo "#define PCI_33M" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PQ_MDS_PIB 1" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _66_,$@)" ] ; then \
-		$(XECHO) -n "...66M..." ; \
 		echo "#define PCI_66M" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PQ_MDS_PIB 1" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _ATM_,$@)" ] ; then \
-		$(XECHO) -n "...ATM..." ; \
 		echo "#define CONFIG_PQ_MDS_PIB 1" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PQ_MDS_PIB_ATM	1" >>$(obj)include/config.h ; \
 	fi ;
-	@$(MKCONFIG) -a MPC832XEMDS powerpc mpc83xx mpc832xemds freescale
+	@$(MKCONFIG) -n $@ -a MPC832XEMDS powerpc mpc83xx mpc832xemds freescale
 
 MPC8349EMDS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc83xx mpc8349emds freescale
@@ -2311,7 +2174,7 @@ MPC8349ITXGP_config:	unconfig
 	@if [ "$(findstring LOWBOOT,$@)" ] ; then \
 		echo "TEXT_BASE = 0xFE000000" >$(obj)board/freescale/mpc8349itx/config.tmp ; \
 	fi
-	@$(MKCONFIG) -a -n $(@:_config=) MPC8349ITX powerpc mpc83xx mpc8349itx freescale
+	@$(MKCONFIG) -n $@ -a MPC8349ITX powerpc mpc83xx mpc8349itx freescale
 
 MPC8360EMDS_config \
 MPC8360EMDS_HOST_33_config \
@@ -2320,49 +2183,42 @@ MPC8360EMDS_SLAVE_config \
 MPC8360EMDS_ATM_config: unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _HOST_,$@)" ] ; then \
-		$(XECHO) -n "... PCI HOST " ; \
 		echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _SLAVE_,$@)" ] ; then \
-		$(XECHO) "...PCI SLAVE 66M"  ; \
 		echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PCISLAVE" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _33_,$@)" ] ; then \
-		$(XECHO) -n "...33M ..." ; \
 		echo "#define PCI_33M" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PQ_MDS_PIB 1" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _66_,$@)" ] ; then \
-		$(XECHO) -n "...66M..." ; \
 		echo "#define PCI_66M" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PQ_MDS_PIB 1" >>$(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _ATM_,$@)" ] ; then \
-		$(XECHO) -n "...ATM..." ; \
 		echo "#define CONFIG_PQ_MDS_PIB 1" >>$(obj)include/config.h ; \
 		echo "#define CONFIG_PQ_MDS_PIB_ATM	1" >>$(obj)include/config.h ; \
 	fi ;
-	@$(MKCONFIG) -a MPC8360EMDS powerpc mpc83xx mpc8360emds freescale
+	@$(MKCONFIG) -n $@ -a MPC8360EMDS powerpc mpc83xx mpc8360emds freescale
 
 MPC8360ERDK_33_config \
 MPC8360ERDK_66_config \
 MPC8360ERDK_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _33_,$@)" ] ; then \
-		$(XECHO) -n "... CLKIN 33MHz " ; \
 		echo "#define CONFIG_CLKIN_33MHZ" >>$(obj)include/config.h ;\
 	fi ;
-	@$(MKCONFIG) -a MPC8360ERDK powerpc mpc83xx mpc8360erdk freescale
+	@$(MKCONFIG) -n $@ -a MPC8360ERDK powerpc mpc83xx mpc8360erdk freescale
 
 MPC837XEMDS_config \
 MPC837XEMDS_HOST_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _HOST_,$@)" ] ; then \
-		$(XECHO) -n "... PCI HOST " ; \
 		echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
 	fi ;
-	@$(MKCONFIG) -a MPC837XEMDS powerpc mpc83xx mpc837xemds freescale
+	@$(MKCONFIG) -n $@ -a MPC837XEMDS powerpc mpc83xx mpc837xemds freescale
 
 MPC837XERDB_config:	unconfig
 	@$(MKCONFIG) -a MPC837XERDB powerpc mpc83xx mpc837xerdb freescale
@@ -2373,29 +2229,27 @@ MVBLM7_config: unconfig
 sbc8349_config \
 sbc8349_PCI_33_config \
 sbc8349_PCI_66_config: unconfig
-	@$(MKCONFIG) -t $(@:_config=) sbc8349 powerpc mpc83xx sbc8349
+	@$(MKCONFIG) -n $@ -t $(@:_config=) sbc8349 powerpc mpc83xx sbc8349
 
 SIMPC8313_LP_config \
 SIMPC8313_SP_config: unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/sheldon/simpc8313
 	@if [ "$(findstring _LP_,$@)" ] ; then \
-		$(XECHO) -n "...Large Page NAND..." ; \
 		echo "#define CONFIG_NAND_LP" >> $(obj)include/config.h ; \
 	fi ; \
 	if [ "$(findstring _SP_,$@)" ] ; then \
-		$(XECHO) -n "...Small Page NAND..." ; \
 		echo "#define CONFIG_NAND_SP" >> $(obj)include/config.h ; \
 	fi ;
-	@$(MKCONFIG) -a SIMPC8313 powerpc mpc83xx simpc8313 sheldon
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) -n $@ -a SIMPC8313 powerpc mpc83xx simpc8313 sheldon
 
 TQM834x_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc83xx tqm834x tqc
 
 caddy2_config \
 vme8349_config:		unconfig
-	@$(MKCONFIG) -t $(@:_config=) vme8349 powerpc mpc83xx vme8349 esd
+	@$(MKCONFIG) -n $@ -t $(@:_config=) vme8349 powerpc mpc83xx vme8349 esd
 
 edb9301_config \
 edb9302_config \
@@ -2405,7 +2259,7 @@ edb9307a_config \
 edb9312_config \
 edb9315_config \
 edb9315a_config: unconfig
-	@$(MKCONFIG) -t $(@:_config=) edb93xx arm arm920t edb93xx NULL ep93xx
+	@$(MKCONFIG) -n $@ -t $(@:_config=) edb93xx arm arm920t edb93xx NULL ep93xx
 
 #########################################################################
 ## MPC85xx Systems
@@ -2419,7 +2273,7 @@ MPC8536DS_SDCARD_config \
 MPC8536DS_SPIFLASH_config \
 MPC8536DS_36BIT_config \
 MPC8536DS_config:       unconfig
-	@$(MKCONFIG) -t $(@:_config=) MPC8536DS powerpc mpc85xx mpc8536ds freescale
+	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8536DS powerpc mpc85xx mpc8536ds freescale
 
 MPC8540ADS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8540ads freescale
@@ -2428,21 +2282,15 @@ MPC8540EVAL_config \
 MPC8540EVAL_33_config \
 MPC8540EVAL_66_config \
 MPC8540EVAL_33_slave_config \
-MPC8540EVAL_66_slave_config:	  unconfig
+MPC8540EVAL_66_slave_config:	unconfig
 	@mkdir -p $(obj)include
-	@if [ "$(findstring _33_,$@)" ] ; then \
-		$(XECHO) "... 33 MHz PCI" ; \
-	else \
+	@if [ -z "$(findstring _33_,$@)" ] ; then \
 		echo "#define CONFIG_SYSCLK_66M" >>$(obj)include/config.h ; \
-		$(XECHO) "... 66 MHz PCI" ; \
 	fi ; \
 	if [ "$(findstring _slave_,$@)" ] ; then \
 		echo "#define CONFIG_PCI_SLAVE" >>$(obj)include/config.h ; \
-		$(XECHO) " slave" ; \
-	else \
-		$(XECHO) " host" ; \
 	fi
-	@$(MKCONFIG) -a MPC8540EVAL powerpc mpc85xx mpc8540eval
+	@$(MKCONFIG) -n $@ -a MPC8540EVAL powerpc mpc85xx mpc8540eval
 
 MPC8560ADS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8560ads freescale
@@ -2452,9 +2300,8 @@ MPC8541CDS_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _legacy_,$@)" ] ; then \
 		echo "#define CONFIG_LEGACY" >>$(obj)include/config.h ; \
-		$(XECHO) "... legacy" ; \
 	fi
-	@$(MKCONFIG) -a MPC8541CDS powerpc mpc85xx mpc8541cds freescale
+	@$(MKCONFIG) -n $@ -a MPC8541CDS powerpc mpc85xx mpc8541cds freescale
 
 MPC8544DS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8544ds freescale
@@ -2464,18 +2311,16 @@ MPC8548CDS_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _legacy_,$@)" ] ; then \
 		echo "#define CONFIG_LEGACY" >>$(obj)include/config.h ; \
-		$(XECHO) "... legacy" ; \
 	fi
-	@$(MKCONFIG) -a MPC8548CDS powerpc mpc85xx mpc8548cds freescale
+	@$(MKCONFIG) -n $@ -a MPC8548CDS powerpc mpc85xx mpc8548cds freescale
 
 MPC8555CDS_legacy_config \
 MPC8555CDS_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _legacy_,$@)" ] ; then \
 		echo "#define CONFIG_LEGACY" >>$(obj)include/config.h ; \
-		$(XECHO) "... legacy" ; \
 	fi
-	@$(MKCONFIG) -a MPC8555CDS powerpc mpc85xx mpc8555cds freescale
+	@$(MKCONFIG) -n $@ -a MPC8555CDS powerpc mpc85xx mpc8555cds freescale
 
 MPC8568MDS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8568mds freescale
@@ -2483,15 +2328,15 @@ MPC8568MDS_config:	unconfig
 MPC8569MDS_ATM_config \
 MPC8569MDS_NAND_config \
 MPC8569MDS_config:	unconfig
-	@$(MKCONFIG) -t $(@:_config=) MPC8569MDS powerpc mpc85xx mpc8569mds freescale
+	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8569MDS powerpc mpc85xx mpc8569mds freescale
 
 MPC8572DS_36BIT_config \
 MPC8572DS_config:       unconfig
-	@$(MKCONFIG) -t $(@:_config=) MPC8572DS powerpc mpc85xx mpc8572ds freescale
+	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8572DS powerpc mpc85xx mpc8572ds freescale
 
 P2020DS_36BIT_config \
 P2020DS_config:		unconfig
-	@$(MKCONFIG) -t $(@:_config=) P2020DS powerpc mpc85xx p2020ds freescale
+	@$(MKCONFIG) -n $@ -t $(@:_config=) P2020DS powerpc mpc85xx p2020ds freescale
 
 P1011RDB_config	\
 P1011RDB_NAND_config \
@@ -2509,7 +2354,7 @@ P2020RDB_config \
 P2020RDB_NAND_config \
 P2020RDB_SDCARD_config \
 P2020RDB_SPIFLASH_config:	unconfig
-	@$(MKCONFIG) -t $(@:_config=) P1_P2_RDB powerpc mpc85xx p1_p2_rdb freescale
+	@$(MKCONFIG) -n $@ -t $(@:_config=) P1_P2_RDB powerpc mpc85xx p1_p2_rdb freescale
 
 PM854_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx pm854
@@ -2520,19 +2365,19 @@ PM856_config:	unconfig
 sbc8540_config \
 sbc8540_33_config \
 sbc8540_66_config:	unconfig
-	@$(MKCONFIG) -t $(@:_config=) SBC8540 powerpc mpc85xx sbc8560
+	@$(MKCONFIG) -n $@ -t $(@:_config=) SBC8540 powerpc mpc85xx sbc8560
 
 sbc8548_config \
 sbc8548_PCI_33_config \
 sbc8548_PCI_66_config \
 sbc8548_PCI_33_PCIE_config \
 sbc8548_PCI_66_PCIE_config: unconfig
-	@$(MKCONFIG) -t $(@:_config=) sbc8548 powerpc mpc85xx sbc8548
+	@$(MKCONFIG) -n $@ -t $(@:_config=) sbc8548 powerpc mpc85xx sbc8548
 
 sbc8560_config \
 sbc8560_33_config \
 sbc8560_66_config:	unconfig
-	@$(MKCONFIG) -t $(@:_config=) sbc8560 powerpc mpc85xx sbc8560
+	@$(MKCONFIG) -n $@ -t $(@:_config=) sbc8560 powerpc mpc85xx sbc8560
 
 socrates_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx socrates
@@ -2545,9 +2390,8 @@ stxssa_4M_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _4M_,$@)" ] ; then \
 		echo "#define CONFIG_STXSSA_4M" >>$(obj)include/config.h ; \
-		$(XECHO) "... with 4 MiB flash memory" ; \
 	fi
-	@$(MKCONFIG) -a stxssa powerpc mpc85xx stxssa stx
+	@$(MKCONFIG) -n $@ -a stxssa powerpc mpc85xx stxssa stx
 
 TQM8540_config		\
 TQM8541_config		\
@@ -2559,13 +2403,12 @@ TQM8560_config:		unconfig
 	@mkdir -p $(obj)include
 	@BTYPE=$(@:_config=); \
 	CTYPE=$(subst TQM,,$(subst _AG,,$(subst _BE,,$(@:_config=)))); \
-	$(XECHO) "... "$${BTYPE}" (MPC"$${CTYPE}")"; \
 	echo "#define CONFIG_MPC$${CTYPE}">>$(obj)include/config.h; \
 	echo "#define CONFIG_$${BTYPE}">>$(obj)include/config.h; \
 	echo "#define CONFIG_HOSTNAME tqm$${CTYPE}">>$(obj)include/config.h; \
 	echo "#define CONFIG_BOARDNAME \"$${BTYPE}\"">>$(obj)include/config.h;
-	@$(MKCONFIG) -a TQM85xx powerpc mpc85xx tqm85xx tqc
 	@echo "CONFIG_$(@:_config=) = y">>$(obj)include/config.mk;
+	@$(MKCONFIG) -n $@ -a TQM85xx powerpc mpc85xx tqm85xx tqc
 
 XPEDITE5200_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx xpedite5200 xes
@@ -2585,9 +2428,8 @@ MPC8641HPCN_config:    unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _36BIT_,$@)" ] ; then \
 		echo "#define CONFIG_PHYS_64BIT" >>$(obj)include/config.h ; \
-		$(XECHO) "... enabling 36-bit physical addressing." ; \
 	fi
-	@$(MKCONFIG) -a MPC8641HPCN powerpc mpc86xx mpc8641hpcn freescale
+	@$(MKCONFIG) -n $@ -a MPC8641HPCN powerpc mpc86xx mpc8641hpcn freescale
 
 sbc8641d_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc86xx sbc8641d
@@ -2619,7 +2461,7 @@ ELPPC_config: unconfig
 
 EVB64260_config	\
 EVB64260_750CX_config:	unconfig
-	@$(MKCONFIG) EVB64260 powerpc 74xx_7xx evb64260
+	@$(MKCONFIG) -n $@ EVB64260 powerpc 74xx_7xx evb64260
 
 mpc7448hpc2_config:  unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx mpc7448hpc2 freescale
@@ -2635,11 +2477,11 @@ p3m7448_config:		unconfig
 	else \
 		echo "#define CONFIG_P3M7448" >>$(obj)include/config.h ; \
 	fi
-	@$(MKCONFIG) -a p3mx powerpc 74xx_7xx p3mx prodrive
+	@$(MKCONFIG) -n $@ -a p3mx powerpc 74xx_7xx p3mx prodrive
 
 PCIPPC2_config \
 PCIPPC6_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx pcippc2
+	@$(MKCONFIG) -n $@ $(@:_config=) powerpc 74xx_7xx pcippc2
 
 ppmc7xx_config: unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx ppmc7xx
@@ -2693,7 +2535,7 @@ CPUAT91_RAM_config \
 CPUAT91_config	:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_$(@:_config=) 1"	>$(obj)include/config.h
-	@$(MKCONFIG) -a cpuat91 arm arm920t cpuat91 eukrea at91rm9200
+	@$(MKCONFIG) -n $@ -a cpuat91 arm arm920t cpuat91 eukrea at91rm9200
 
 csb637_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm920t csb637 NULL at91rm9200
@@ -2731,21 +2573,17 @@ at91sam9g20ek_config	:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring 9g20,$@)" ] ; then \
 		echo "#define CONFIG_AT91SAM9G20EK 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... 9G20 Variant" ; \
 	else \
 		echo "#define CONFIG_AT91SAM9260EK 1"	>>$(obj)include/config.h ; \
 	fi;
 	@if [ "$(findstring _nandflash,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_NANDFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in NAND FLASH" ; \
 	elif [ "$(findstring dataflash_cs0,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_DATAFLASH_CS0 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS0" ; \
 	else \
 		echo "#define CONFIG_SYS_USE_DATAFLASH_CS1 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS1" ; \
 	fi;
-	@$(MKCONFIG) -a at91sam9260ek arm arm926ejs at91sam9260ek atmel at91
+	@$(MKCONFIG) -n $@ -a at91sam9260ek arm arm926ejs at91sam9260ek atmel at91
 
 at91sam9xeek_nandflash_config \
 at91sam9xeek_dataflash_cs0_config \
@@ -2754,15 +2592,12 @@ at91sam9xeek_config	:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _nandflash,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_NANDFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in NAND FLASH" ; \
 	elif [ "$(findstring dataflash_cs0,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_DATAFLASH_CS0 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS0" ; \
 	else \
 		echo "#define CONFIG_SYS_USE_DATAFLASH_CS1 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS1" ; \
 	fi;
-	@$(MKCONFIG) -n at91sam9xeek -a at91sam9260ek arm arm926ejs at91sam9260ek atmel at91
+	@$(MKCONFIG) -n $@ -a at91sam9260ek arm arm926ejs at91sam9260ek atmel at91
 
 at91sam9261ek_nandflash_config \
 at91sam9261ek_dataflash_cs0_config \
@@ -2775,21 +2610,17 @@ at91sam9g10ek_config	:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring 9g10,$@)" ] ; then \
 		echo "#define CONFIG_AT91SAM9G10EK 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... 9G10 Variant" ; \
 	else \
 		echo "#define CONFIG_AT91SAM9261EK 1"	>>$(obj)include/config.h ; \
 	fi;
 	@if [ "$(findstring _nandflash,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_NANDFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in NAND FLASH" ; \
 	elif [ "$(findstring dataflash_cs0,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_DATAFLASH_CS3 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS3" ; \
 	else \
 		echo "#define CONFIG_SYS_USE_DATAFLASH_CS0 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS0" ; \
 	fi;
-	@$(MKCONFIG) -a at91sam9261ek arm arm926ejs at91sam9261ek atmel at91
+	@$(MKCONFIG) -n $@ -a at91sam9261ek arm arm926ejs at91sam9261ek atmel at91
 
 at91sam9263ek_norflash_config \
 at91sam9263ek_norflash_boot_config \
@@ -2800,19 +2631,15 @@ at91sam9263ek_config	:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _nandflash,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_NANDFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in NAND FLASH" ; \
 	elif [ "$(findstring norflash,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_NORFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in NOR FLASH" ; \
 	else \
 		echo "#define CONFIG_SYS_USE_DATAFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS0" ; \
 	fi;
 	@if [ "$(findstring norflash_boot,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_BOOT_NORFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... and boot from NOR FLASH" ; \
 	fi;
-	@$(MKCONFIG) -a at91sam9263ek arm arm926ejs at91sam9263ek atmel at91
+	@$(MKCONFIG) -n $@ -a at91sam9263ek arm arm926ejs at91sam9263ek atmel at91
 
 at91sam9rlek_nandflash_config \
 at91sam9rlek_dataflash_config \
@@ -2821,12 +2648,10 @@ at91sam9rlek_config	:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _nandflash,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_NANDFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in NAND FLASH" ; \
 	else \
 		echo "#define CONFIG_SYS_USE_DATAFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS0" ; \
 	fi;
-	@$(MKCONFIG) -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91
+	@$(MKCONFIG) -n $@ -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91
 
 CPU9G20_128M_config \
 CPU9G20_config \
@@ -2834,7 +2659,7 @@ CPU9260_128M_config \
 CPU9260_config	:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_$(@:_config=) 1" >$(obj)include/config.h
-	@$(MKCONFIG) -a cpu9260 arm arm926ejs cpu9260 eukrea at91
+	@$(MKCONFIG) -n $@ -a cpu9260 arm arm926ejs cpu9260 eukrea at91
 
 meesc_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs meesc esd at91
@@ -2853,19 +2678,15 @@ at91sam9g45ekes_config	:	unconfig
 	@mkdir -p $(obj)include
 		@if [ "$(findstring 9m10,$@)" ] ; then \
 		echo "#define CONFIG_AT91SAM9M10G45EK 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... 9M10G45 Variant" ; \
 	else \
 		echo "#define CONFIG_AT91SAM9G45EKES 1"	>>$(obj)include/config.h ; \
 	fi;
-
 	@if [ "$(findstring _nandflash,$@)" ] ; then \
 		echo "#define CONFIG_SYS_USE_NANDFLASH 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in NAND FLASH" ; \
 	else \
 		echo "#define CONFIG_ATMEL_SPI 1"	>>$(obj)include/config.h ; \
-		$(XECHO) "... with environment variable in SPI DATAFLASH CS0" ; \
 	fi;
-	@$(MKCONFIG) -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91
+	@$(MKCONFIG) -n $@ -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91
 
 otc570_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs otc570 esd at91
@@ -2878,7 +2699,7 @@ SBC35_A9G20_EEPROM_config \
 SBC35_A9G20_config	:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_$(@:_config=) 1" >$(obj)include/config.h
-	@$(MKCONFIG) -a sbc35_a9g20 arm arm926ejs sbc35_a9g20 calao at91
+	@$(MKCONFIG) -n $@ -a sbc35_a9g20 arm arm926ejs sbc35_a9g20 calao at91
 
 TNY_A9G20_NANDFLASH_config \
 TNY_A9G20_EEPROM_config \
@@ -2888,7 +2709,7 @@ TNY_A9260_EEPROM_config \
 TNY_A9260_config	:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_$(@:_config=) 1" >$(obj)include/config.h
-	@$(MKCONFIG) -a tny_a9260 arm arm926ejs tny_a9260 calao at91
+	@$(MKCONFIG) -n $@ -a tny_a9260 arm arm926ejs tny_a9260 calao at91
 
 ########################################################################
 ## ARM Integrator boards - see doc/README-integrator for more info.
@@ -2916,32 +2737,17 @@ cp922_XA10_config	\
 cp1026_config: unconfig
 	@board/armltd/integrator/split_by_variant.sh cp $@
 
-da830evm_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs da830evm davinci davinci
-
-davinci_dvevm_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs dvevm davinci davinci
-
-davinci_schmoogie_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs schmoogie davinci davinci
-
-davinci_sffsdr_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs sffsdr davinci davinci
-
-davinci_sonata_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs sonata davinci davinci
-
-davinci_dm355evm_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs dm355evm davinci davinci
-
-davinci_dm355leopard_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs dm355leopard davinci davinci
-
-davinci_dm365evm_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs dm365evm davinci davinci
-
-davinci_dm6467evm_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs dm6467evm davinci davinci
+da830evm_config			\
+davinci_dvevm_config		\
+davinci_schmoogie_config	\
+davinci_sffsdr_config		\
+davinci_sonata_config		\
+davinci_dm355evm_config		\
+davinci_dm355leopard_config	\
+davinci_dm365evm_config		\
+davinci_dm6467evm_config	:	unconfig
+	@$(MKCONFIG) -n $@ $(@:_config=) arm arm926ejs \
+		$(subst davinci_,,$(@:_config=)) davinci davinci
 
 guruplug_config: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
@@ -2952,7 +2758,7 @@ imx27lite_config:	unconfig
 
 lpd7a400_config \
 lpd7a404_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm lh7a40x lpd7a40x
+	@$(MKCONFIG) -n $(@:_config=) arm lh7a40x lpd7a40x
 
 mv88f6281gtw_ge_config: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
@@ -2972,11 +2778,8 @@ nhk8815_onenand_config:	unconfig
 	@ > $(obj)include/config.h
 	@if [ "$(findstring _onenand, $@)" ] ; then \
 		echo "#define CONFIG_BOOT_ONENAND" >> $(obj)include/config.h; \
-		$(XECHO) "... configured to boot from OneNand Flash"; \
-	else \
-		$(XECHO) "... configured to boot from Nand Flash"; \
 	fi
-	@$(MKCONFIG) -a nhk8815 arm arm926ejs nhk8815 st nomadik
+	@$(MKCONFIG) -n $@ -a nhk8815 arm arm926ejs nhk8815 st nomadik
 
 omap1510inn_config :	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm925t omap1510inn ti
@@ -2994,15 +2797,12 @@ omap1610h2_cs_autoboot_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _cs0boot_, $@)" ] ; then \
 		echo "#define CONFIG_CS0_BOOT" >> .$(obj)include/config.h ; \
-		$(XECHO) "... configured for CS0 boot"; \
 	elif [ "$(findstring _cs_autoboot_, $@)" ] ; then \
 		echo "#define CONFIG_CS_AUTOBOOT" >> $(obj)include/config.h ; \
-		$(XECHO) "... configured for CS_AUTO boot"; \
 	else \
 		echo "#define CONFIG_CS3_BOOT" >> $(obj)include/config.h ; \
-		$(XECHO) "... configured for CS3 boot"; \
 	fi;
-	@$(MKCONFIG) -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn ti omap
+	@$(MKCONFIG) -n $@ -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn ti omap
 
 omap5912osk_config :	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
@@ -3018,12 +2818,10 @@ omap730p2_cs3boot_config :	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _cs0boot_, $@)" ] ; then \
 		echo "#define CONFIG_CS0_BOOT" >> $(obj)include/config.h ; \
-		$(XECHO) "... configured for CS0 boot"; \
 	else \
 		echo "#define CONFIG_CS3_BOOT" >> $(obj)include/config.h ; \
-		$(XECHO) "... configured for CS3 boot"; \
 	fi;
-	@$(MKCONFIG) -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 ti omap
+	@$(MKCONFIG) -n $@ -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 ti omap
 
 rd6281a_config: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
@@ -3059,12 +2857,10 @@ SX1_config:		unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring _stdout_serial_, $@)" ] ; then \
 		echo "#undef CONFIG_STDOUT_USBTTY" >> $(obj)include/config.h ; \
-		$(XECHO) "... configured for stdout serial"; \
 	else \
 		echo "#define CONFIG_STDOUT_USBTTY" >> $(obj)include/config.h ; \
-		$(XECHO) "... configured for stdout usbtty"; \
 	fi;
-	@$(MKCONFIG) SX1 arm arm925t sx1
+	@$(MKCONFIG) -n $@ SX1 arm arm925t sx1
 
 # TRAB default configuration:	8 MB Flash, 32 MB RAM
 xtract_trab = $(subst _bigram,,$(subst _bigflash,,$(subst _old,,$(subst _config,,$1))))
@@ -3078,25 +2874,22 @@ trab_old_config:	unconfig
 	@[ -z "$(findstring _bigram,$@)" ] || \
 		{ echo "#define CONFIG_FLASH_8MB"  >>$(obj)include/config.h ; \
 		  echo "#define CONFIG_RAM_32MB"   >>$(obj)include/config.h ; \
-		  $(XECHO) "... with 8 MB Flash, 32 MB RAM" ; \
 		}
 	@[ -z "$(findstring _bigflash,$@)" ] || \
 		{ echo "#define CONFIG_FLASH_16MB" >>$(obj)include/config.h ; \
 		  echo "#define CONFIG_RAM_16MB"   >>$(obj)include/config.h ; \
-		  $(XECHO) "... with 16 MB Flash, 16 MB RAM" ; \
 		  echo "TEXT_BASE = 0x0CF40000" >$(obj)board/trab/config.tmp ; \
 		}
 	@[ -z "$(findstring _old,$@)" ] || \
 		{ echo "#define CONFIG_FLASH_8MB"  >>$(obj)include/config.h ; \
 		  echo "#define CONFIG_RAM_16MB"   >>$(obj)include/config.h ; \
-		  $(XECHO) "... with 8 MB Flash, 16 MB RAM" ; \
 		  echo "TEXT_BASE = 0x0CF40000" >$(obj)board/trab/config.tmp ; \
 		}
-	@$(MKCONFIG) -a $(call xtract_trab,$@) arm arm920t trab NULL s3c24x0
+	@$(MKCONFIG) -n $@ -a $(call xtract_trab,$@) arm arm920t trab NULL s3c24x0
 
 tx25_config	: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs tx25 karo mx25
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) $(@:_config=) arm arm926ejs tx25 karo mx25
 
 VCMA9_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm920t vcma9 mpl s3c24x0
@@ -3233,9 +3026,8 @@ scpu_config:	unconfig
 	@mkdir -p $(obj)include
 	@if [ "$(findstring scpu_,$@)" ] ; then \
 		echo "#define CONFIG_SCPU"	>>$(obj)include/config.h ; \
-		$(XECHO) "... on SCPU board variant" ; \
 	fi
-	@$(MKCONFIG) -a pdnb3 arm ixp pdnb3 prodrive
+	@$(MKCONFIG) -n $@ -a pdnb3 arm ixp pdnb3 prodrive
 
 pxa255_idp_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm pxa pxa255_idp
@@ -3246,7 +3038,7 @@ trizepsiv_config	:	unconfig
 	@if [ "$(findstring polaris,$@)" ] ; then \
 		echo "#define CONFIG_POLARIS 1"	>>$(obj)include/config.h ; \
 	fi;
-	@$(MKCONFIG) -a trizepsiv arm pxa trizepsiv
+	@$(MKCONFIG) -n $@ -a trizepsiv arm pxa trizepsiv
 
 wepep250_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm pxa wepep250
@@ -3270,8 +3062,8 @@ zylonite_config :
 apollon_config		: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_ONENAND_U_BOOT" > $(obj)include/config.h
-	@$(MKCONFIG) $(@:_config=) arm arm1136 apollon NULL omap24xx
 	@echo "CONFIG_ONENAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) $(@:_config=) arm arm1136 apollon NULL omap24xx
 
 imx31_litekit_config	: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 imx31_litekit logicpd mx31
@@ -3282,7 +3074,7 @@ imx31_phycore_config	: unconfig
 	@if [ -n "$(findstring _eet_,$@)" ]; then			\
 		echo "#define CONFIG_IMX31_PHYCORE_EET" >> $(obj)include/config.h;	\
 	fi
-	@$(MKCONFIG) -a imx31_phycore arm arm1136 imx31_phycore NULL mx31
+	@$(MKCONFIG) -n $@ -a imx31_phycore arm arm1136 imx31_phycore NULL mx31
 
 mx31ads_config		: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31
@@ -3296,7 +3088,7 @@ mx31pdk_nand_config	: unconfig
 		echo "#define CONFIG_SKIP_LOWLEVEL_INIT" >> $(obj)include/config.h;	\
 		echo "#define CONFIG_SKIP_RELOCATE_UBOOT" >> $(obj)include/config.h;	\
 	fi
-	@$(MKCONFIG) -a mx31pdk arm arm1136 mx31pdk freescale mx31
+	@$(MKCONFIG) -n $@ -a mx31pdk arm arm1136 mx31pdk freescale mx31
 
 mx51evk_config	: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 mx51evk freescale mx51
@@ -3315,14 +3107,13 @@ smdk6400_config	:	unconfig
 	@mkdir -p $(obj)include $(obj)board/samsung/smdk6400
 	@mkdir -p $(obj)nand_spl/board/samsung/smdk6400
 	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
+	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 	@if [ -z "$(findstring smdk6400_noUSB_config,$@)" ]; then			\
 		echo "RAM_TEXT = 0x57e00000" >> $(obj)board/samsung/smdk6400/config.tmp;\
-		$(MKCONFIG) $(@:_config=) arm arm1176 smdk6400 samsung s3c64xx;		\
 	else										\
 		echo "RAM_TEXT = 0xc7e00000" >> $(obj)board/samsung/smdk6400/config.tmp;\
-		$(MKCONFIG) $(@:_noUSB_config=) arm arm1176 smdk6400 samsung s3c64xx;	\
 	fi
-	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) $(subst _noUSB,,$(@:_config=)) arm arm1176 smdk6400 samsung s3c64xx
 
 #========================================================================
 # i386
@@ -3349,26 +3140,18 @@ sc520_spunk_rel_config	:	unconfig
 ## MIPS32 4Kc
 #########################################################################
 
-xtract_incaip = $(subst _100MHz,,$(subst _133MHz,,$(subst _150MHz,,$(subst _config,,$1))))
-
 incaip_100MHz_config	\
 incaip_133MHz_config	\
 incaip_150MHz_config	\
 incaip_config: unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring _100MHz,$@)" ] || \
-		{ echo "#define CPU_CLOCK_RATE 100000000" >>$(obj)include/config.h ; \
-		  $(XECHO) "... with 100MHz system clock" ; \
-		}
+		echo "#define CPU_CLOCK_RATE 100000000" >>$(obj)include/config.h
 	@[ -z "$(findstring _133MHz,$@)" ] || \
-		{ echo "#define CPU_CLOCK_RATE 133000000" >>$(obj)include/config.h ; \
-		  $(XECHO) "... with 133MHz system clock" ; \
-		}
+		echo "#define CPU_CLOCK_RATE 133000000" >>$(obj)include/config.h
 	@[ -z "$(findstring _150MHz,$@)" ] || \
-		{ echo "#define CPU_CLOCK_RATE 150000000" >>$(obj)include/config.h ; \
-		  $(XECHO) "... with 150MHz system clock" ; \
-		}
-	@$(MKCONFIG) -a $(call xtract_incaip,$@) mips mips incaip
+		echo "#define CPU_CLOCK_RATE 150000000" >>$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a incaip mips mips incaip
 
 tb0229_config: unconfig
 	@$(MKCONFIG) $(@:_config=) mips mips tb0229
@@ -3386,27 +3169,17 @@ vct_platinumavc_small_config	\
 vct_platinumavc_onenand_config	\
 vct_platinumavc_onenand_small_config: unconfig
 	@mkdir -p $(obj)include
-	@if [ "$(findstring _premium,$@)" ] ; then \
-		echo "#define CONFIG_VCT_PREMIUM" > $(obj)include/config.h ; \
-		$(XECHO) "... on Premium board variant" ; \
-	fi
-	@if [ "$(findstring _platinum_,$@)" ] ; then \
-		echo "#define CONFIG_VCT_PLATINUM" > $(obj)include/config.h ; \
-		$(XECHO) "... on Platinum board variant" ; \
-	fi
-	@if [ "$(findstring _platinumavc,$@)" ] ; then \
-		echo "#define CONFIG_VCT_PLATINUMAVC" > $(obj)include/config.h ; \
-		$(XECHO) "... on PlatinumAVC board variant" ; \
-	fi
-	@if [ "$(findstring _onenand,$@)" ] ; then \
-		echo "#define CONFIG_VCT_ONENAND" >> $(obj)include/config.h ; \
-		$(XECHO) "... on OneNAND board variant" ; \
-	fi
-	@if [ "$(findstring _small,$@)" ] ; then \
-		echo "#define CONFIG_VCT_SMALL_IMAGE" >> $(obj)include/config.h ; \
-		$(XECHO) "... stripped down image variant" ; \
-	fi
-	@$(MKCONFIG) -a vct mips mips vct micronas
+	@[ -z "$(findstring _premium,$@)" ] || \
+		echo "#define CONFIG_VCT_PREMIUM" > $(obj)include/config.h
+	@[ -z "$(findstring _platinum_,$@)" ] || \
+		echo "#define CONFIG_VCT_PLATINUM" > $(obj)include/config.h
+	@[ -z "$(findstring _platinumavc,$@)" ] || \
+		echo "#define CONFIG_VCT_PLATINUMAVC" > $(obj)include/config.h
+	@[ -z "$(findstring _onenand,$@)" ] || \
+		echo "#define CONFIG_VCT_ONENAND" >> $(obj)include/config.h
+	@[ -z "$(findstring _small,$@)" ] || \
+		echo "#define CONFIG_VCT_SMALL_IMAGE" >> $(obj)include/config.h
+	@$(MKCONFIG)  -n $@ -a vct mips mips vct micronas
 
 #########################################################################
 ## MIPS32 AU1X00
@@ -3528,15 +3301,9 @@ bf527-ezkit-v2_config	: unconfig
 atngw100_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) avr32 at32ap atngw100 atmel at32ap700x
 
-atstk1002_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap atstk1000 atmel at32ap700x
-
-atstk1003_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap atstk1000 atmel at32ap700x
-
-atstk1004_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap atstk1000 atmel at32ap700x
-
+atstk1002_config	\
+atstk1003_config	\
+atstk1004_config	\
 atstk1006_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) avr32 at32ap atstk1000 atmel at32ap700x
 
@@ -3619,9 +3386,8 @@ sh7785lcr_config  :   unconfig
 		echo "#define CONFIG_SH_32BIT 1" >> $(obj)include/config.h ; \
 		echo "TEXT_BASE = 0x8ff80000" > \
 			$(obj)board/renesas/sh7785lcr/config.tmp ; \
-		  $(XECHO) " ... enable 32-Bit Address Extended Mode" ; \
 	fi
-	@$(MKCONFIG) -a $(call xtract_sh7785lcr,$@) sh sh4 sh7785lcr renesas
+	@$(MKCONFIG) -n $@ -a $(call xtract_sh7785lcr,$@) sh sh4 sh7785lcr renesas
 
 ap325rxa_config  :   unconfig
 	@mkdir -p $(obj)include
-- 
cgit v1.1


From ed7a196cd5c92fb9ed2d503feb96360a029f37bd Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Thu, 27 May 2010 23:18:34 +0200
Subject: Makefile: simplify handling of build target names

Instead of stripping the "_config" part from the make target names in
each call of the "mkconfig" script let this script strip the string.

This prepares the ground for forther simplification of the top level
Makefile.

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 Makefile | 774 +++++++++++++++++++++++++++++++--------------------------------
 mkconfig |   6 +-
 2 files changed, 380 insertions(+), 400 deletions(-)

diff --git a/Makefile b/Makefile
index c83bf84..25d531e 100644
--- a/Makefile
+++ b/Makefile
@@ -486,30 +486,30 @@ unconfig:
 ## MPC5xx Systems
 #########################################################################
 
-canmb_config:	unconfig
-	@$(MKCONFIG) -a canmb powerpc mpc5xxx canmb
-
 cmi_mpc5xx_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc5xx cmi
+	@$(MKCONFIG) $@ powerpc mpc5xx cmi
 
 PATI_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc5xx pati mpl
+	@$(MKCONFIG) $@ powerpc mpc5xx pati mpl
 
 #########################################################################
 ## MPC5xxx Systems
 #########################################################################
 
 aev_config: unconfig
-	@$(MKCONFIG) -a aev powerpc mpc5xxx tqm5200 tqc
+	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
 
 BC3450_config:	unconfig
-	@$(MKCONFIG) -a BC3450 powerpc mpc5xxx bc3450
+	@$(MKCONFIG) $@ powerpc mpc5xxx bc3450
+
+canmb_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc5xxx canmb
 
 cm5200_config:	unconfig
-	@$(MKCONFIG) -a cm5200 powerpc mpc5xxx cm5200
+	@$(MKCONFIG) $@ powerpc mpc5xxx cm5200
 
 cpci5200_config:  unconfig
-	@$(MKCONFIG) -a cpci5200  powerpc mpc5xxx cpci5200 esd
+	@$(MKCONFIG) $@ powerpc mpc5xxx cpci5200 esd
 
 digsy_mtc_config \
 digsy_mtc_LOWBOOT_config	\
@@ -521,7 +521,7 @@ digsy_mtc_RAMBOOT_config:	unconfig
 		echo "TEXT_BASE = 0xFF000000" >$(obj)board/digsy_mtc/config.tmp
 	@[ -z "$(findstring RAMBOOT_,$@)" ] || \
 		echo "TEXT_BASE = 0x00100000" >$(obj)board/digsy_mtc/config.tmp
-	@$(MKCONFIG) -n $@ -a digsy_mtc  powerpc mpc5xxx digsy_mtc
+	@$(MKCONFIG) -n $@ -a digsy_mtc powerpc mpc5xxx digsy_mtc
 
 galaxy5200_LOWBOOT_config \
 galaxy5200_config:	unconfig
@@ -530,7 +530,7 @@ galaxy5200_config:	unconfig
 	@$(MKCONFIG) -n $@ -a galaxy5200 powerpc mpc5xxx galaxy5200
 
 hmi1001_config:	unconfig
-	@$(MKCONFIG) hmi1001 powerpc mpc5xxx hmi1001
+	@$(MKCONFIG) $@ powerpc mpc5xxx hmi1001
 
 Lite5200_config				\
 Lite5200_LOWBOOT_config			\
@@ -555,13 +555,13 @@ icecube_5200_DDR_LOWBOOT08_config:	unconfig
 	@$(MKCONFIG) -n $@ -a IceCube powerpc mpc5xxx icecube
 
 jupiter_config:	unconfig
-	@$(MKCONFIG) jupiter powerpc mpc5xxx jupiter
+	@$(MKCONFIG) $@ powerpc mpc5xxx jupiter
 
 inka4x0_config:	unconfig
-	@$(MKCONFIG) inka4x0 powerpc mpc5xxx inka4x0
+	@$(MKCONFIG) $@ powerpc mpc5xxx inka4x0
 
 ipek01_config: unconfig
-	@$(MKCONFIG) -a ipek01 powerpc mpc5xxx ipek01
+	@$(MKCONFIG) $@ powerpc mpc5xxx ipek01
 
 lite5200b_config	\
 lite5200b_PM_config	\
@@ -609,16 +609,16 @@ prs200_highboot_DDR_config:	unconfig
 	@$(MKCONFIG) -n $@ -a mcc200 powerpc mpc5xxx mcc200
 
 mecp5200_config:  unconfig
-	@$(MKCONFIG) mecp5200  powerpc mpc5xxx mecp5200 esd
+	@$(MKCONFIG) $@ powerpc mpc5xxx mecp5200 esd
 
 motionpro_config:	unconfig
-	@$(MKCONFIG) motionpro powerpc mpc5xxx motionpro
+	@$(MKCONFIG) $@ powerpc mpc5xxx motionpro
 
 mucmc52_config:		unconfig
-	@$(MKCONFIG) mucmc52 powerpc mpc5xxx mucmc52
+	@$(MKCONFIG) $@ powerpc mpc5xxx mucmc52
 
 munices_config:	unconfig
-	@$(MKCONFIG) munices powerpc mpc5xxx munices
+	@$(MKCONFIG) $@ powerpc mpc5xxx munices
 
 MVBC_P_config: unconfig
 	@mkdir -p $(obj)include
@@ -626,15 +626,15 @@ MVBC_P_config: unconfig
 	@ >$(obj)include/config.h
 	@[ -z "$(findstring MVBC_P,$@)" ] || \
 		echo "#define CONFIG_MVBC_P" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a MVBC_P powerpc mpc5xxx mvbc_p matrix_vision
+	@$(MKCONFIG) -n $@ -a $@ powerpc mpc5xxx mvbc_p matrix_vision
 
 MVSMR_config: unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/matrix_vision/mvsmr
-	@$(MKCONFIG) $(@:_config=) powerpc mpc5xxx mvsmr matrix_vision
+	@$(MKCONFIG) $@ powerpc mpc5xxx mvsmr matrix_vision
 
 o2dnt_config:	unconfig
-	@$(MKCONFIG) o2dnt powerpc mpc5xxx o2dnt
+	@$(MKCONFIG) $@ powerpc mpc5xxx o2dnt
 
 pcm030_config \
 pcm030_LOWBOOT_config:	unconfig
@@ -645,7 +645,7 @@ pcm030_LOWBOOT_config:	unconfig
 	@$(MKCONFIG) -n $@ -a pcm030 powerpc mpc5xxx pcm030 phytec
 
 pf5200_config:	unconfig
-	@$(MKCONFIG) pf5200  powerpc mpc5xxx pf5200 esd
+	@$(MKCONFIG) $@ powerpc mpc5xxx pf5200 esd
 
 PM520_config \
 PM520_DDR_config \
@@ -659,10 +659,10 @@ PM520_ROMBOOT_DDR_config:	unconfig
 	@$(MKCONFIG) -n $@ -a PM520 powerpc mpc5xxx pm520
 
 smmaco4_config: unconfig
-	@$(MKCONFIG) -a smmaco4 powerpc mpc5xxx tqm5200 tqc
+	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
 
 spieval_config:	unconfig
-	@$(MKCONFIG) -a spieval powerpc mpc5xxx tqm5200 tqc
+	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
 
 TB5200_B_config \
 TB5200_config:	unconfig
@@ -728,20 +728,20 @@ TQM5200_STK100_config:	unconfig
 	@$(MKCONFIG) -n $@ -a TQM5200 powerpc mpc5xxx tqm5200 tqc
 
 uc101_config:		unconfig
-	@$(MKCONFIG) uc101 powerpc mpc5xxx uc101
+	@$(MKCONFIG) $@ powerpc mpc5xxx uc101
 
 v38b_config: unconfig
-	@$(MKCONFIG) -a v38b powerpc mpc5xxx v38b
+	@$(MKCONFIG) $@ powerpc mpc5xxx v38b
 
 #########################################################################
 ## MPC512x Systems
 #########################################################################
 
 aria_config:	unconfig
-	@$(MKCONFIG) -a aria powerpc mpc512x aria davedenx
+	@$(MKCONFIG) $@ powerpc mpc512x aria davedenx
 
 mecp5123_config:	unconfig
-	@$(MKCONFIG) -a mecp5123 powerpc mpc512x mecp5123 esd
+	@$(MKCONFIG) $@ powerpc mpc512x mecp5123 esd
 
 mpc5121ads_config \
 mpc5121ads_rev2_config	\
@@ -753,7 +753,7 @@ mpc5121ads_rev2_config	\
 	@$(MKCONFIG) -n $@ -a mpc5121ads powerpc mpc512x mpc5121ads freescale
 
 pdm360ng_config:	unconfig
-	@$(MKCONFIG) -a pdm360ng powerpc mpc512x pdm360ng
+	@$(MKCONFIG) $@ powerpc mpc512x pdm360ng
 
 #########################################################################
 ## MPC8xx Systems
@@ -775,70 +775,66 @@ FADS850SAR_config \
 MPC86xADS_config  \
 MPC885ADS_config  \
 FADS860T_config:	unconfig
-	@$(MKCONFIG) -n $@ $(@:_config=) powerpc mpc8xx fads
+	@$(MKCONFIG) -n $@ $@ powerpc mpc8xx fads
 
 AMX860_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx amx860 westel
+	@$(MKCONFIG) $@ powerpc mpc8xx amx860 westel
 
 c2mon_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx c2mon
+	@$(MKCONFIG) $@ powerpc mpc8xx c2mon
 
 CCM_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx CCM siemens
+	@$(MKCONFIG) $@ powerpc mpc8xx CCM siemens
 
 cogent_mpc8xx_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx cogent
+	@$(MKCONFIG) $@ powerpc mpc8xx cogent
 
 ELPT860_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx elpt860 LEOX
+	@$(MKCONFIG) $@ powerpc mpc8xx elpt860 LEOX
 
 EP88x_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx ep88x
+	@$(MKCONFIG) $@ powerpc mpc8xx ep88x
 
 ESTEEM192E_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx esteem192e
+	@$(MKCONFIG) $@ powerpc mpc8xx esteem192e
 
 ETX094_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx etx094
+	@$(MKCONFIG) $@ powerpc mpc8xx etx094
 
 FLAGADM_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx flagadm
-
-xtract_GEN860T = $(subst _SC,,$(subst _config,,$1))
+	@$(MKCONFIG) $@ powerpc mpc8xx flagadm
 
 GEN860T_SC_config	\
 GEN860T_config: unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring _SC,$@)" ] || \
 		echo "#define CONFIG_SC" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_GEN860T,$@) powerpc mpc8xx gen860t
+	@$(MKCONFIG) -n $@ -a GEN860T powerpc mpc8xx gen860t
 
 GENIETV_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx genietv
+	@$(MKCONFIG) $@ powerpc mpc8xx genietv
 
 GTH_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx gth
+	@$(MKCONFIG) $@ powerpc mpc8xx gth
 
 hermes_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx hermes
+	@$(MKCONFIG) $@ powerpc mpc8xx hermes
 
 HMI10_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx tqm8xx tqc
+	@$(MKCONFIG) $@ powerpc mpc8xx tqm8xx tqc
 
 IAD210_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx IAD210 siemens
-
-xtract_ICU862 = $(subst _100MHz,,$(subst _config,,$1))
+	@$(MKCONFIG) $@ powerpc mpc8xx IAD210 siemens
 
 ICU862_100MHz_config	\
 ICU862_config: unconfig
 	@mkdir -p $(obj)include
 	@[ -z "$(findstring _100MHz,$@)" ] || \
 		echo "#define CONFIG_100MHz" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_ICU862,$@) powerpc mpc8xx icu862
+	@$(MKCONFIG) -n $@ -a ICU862 powerpc mpc8xx icu862
 
 IP860_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx ip860
+	@$(MKCONFIG) $@ powerpc mpc8xx ip860
 
 IVML24_256_config \
 IVML24_128_config \
@@ -865,31 +861,29 @@ IVMS8_config:	unconfig
 	@$(MKCONFIG) -n $@ -a IVMS8 powerpc mpc8xx ivm
 
 kmsupx4_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx km8xx keymile
+	@$(MKCONFIG) $@ powerpc mpc8xx km8xx keymile
 
 KUP4K_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx kup4k kup
+	@$(MKCONFIG) $@ powerpc mpc8xx kup4k kup
 
 KUP4X_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx kup4x kup
+	@$(MKCONFIG) $@ powerpc mpc8xx kup4x kup
 
 LANTEC_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx lantec
+	@$(MKCONFIG) $@ powerpc mpc8xx lantec
 
 lwmon_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx lwmon
+	@$(MKCONFIG) $@ powerpc mpc8xx lwmon
 
 MBX_config	\
 MBX860T_config:	unconfig
-	@$(MKCONFIG) -n $@ $(@:_config=) powerpc mpc8xx mbx8xx
+	@$(MKCONFIG) -n $@ $@ powerpc mpc8xx mbx8xx
 
 mgsuvd_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx km8xx keymile
+	@$(MKCONFIG) $@ powerpc mpc8xx km8xx keymile
 
 MHPC_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx mhpc eltec
-
-xtract_NETVIA = $(subst _V2,,$(subst _config,,$1))
+	@$(MKCONFIG) $@ powerpc mpc8xx mhpc eltec
 
 NETVIA_V2_config \
 NETVIA_config:		unconfig
@@ -898,9 +892,7 @@ NETVIA_config:		unconfig
 		echo "#define CONFIG_NETVIA_VERSION 1" >>$(obj)include/config.h
 	@[ -z "$(findstring NETVIA_V2_config,$@)" ] || \
 		echo "#define CONFIG_NETVIA_VERSION 2" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_NETVIA,$@) powerpc mpc8xx netvia
-
-xtract_NETPHONE = $(subst _V2,,$(subst _config,,$1))
+	@$(MKCONFIG) -n $@ -a NETVIA powerpc mpc8xx netvia
 
 NETPHONE_V2_config \
 NETPHONE_config:	unconfig
@@ -909,9 +901,7 @@ NETPHONE_config:	unconfig
 		echo "#define CONFIG_NETPHONE_VERSION 1" >>$(obj)include/config.h
 	@[ -z "$(findstring NETPHONE_V2_config,$@)" ] || \
 		echo "#define CONFIG_NETPHONE_VERSION 2" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_NETPHONE,$@) powerpc mpc8xx netphone
-
-xtract_NETTA = $(subst _SWAPHOOK,,$(subst _6412,,$(subst _ISDN,,$(subst _config,,$1))))
+	@$(MKCONFIG) -n $@ -a NETPHONE powerpc mpc8xx netphone
 
 NETTA_ISDN_6412_SWAPHOOK_config \
 NETTA_ISDN_SWAPHOOK_config \
@@ -934,9 +924,7 @@ NETTA_config:		unconfig
 		echo "#define CONFIG_NETTA_SWAPHOOK 1" >>$(obj)include/config.h
 	@[ -n "$(findstring SWAPHOOK_,$@)" ] || \
 		echo "#undef CONFIG_NETTA_SWAPHOOK" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_NETTA,$@) powerpc mpc8xx netta
-
-xtract_NETTA2 = $(subst _V2,,$(subst _config,,$1))
+	@$(MKCONFIG) -n $@ -a NETTA powerpc mpc8xx netta
 
 NETTA2_V2_config \
 NETTA2_config:		unconfig
@@ -945,7 +933,7 @@ NETTA2_config:		unconfig
 		echo "#define CONFIG_NETTA2_VERSION 1" >>$(obj)include/config.h
 	@[ -z "$(findstring NETTA2_V2_config,$@)" ] || \
 		echo "#define CONFIG_NETTA2_VERSION 2" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_NETTA2,$@) powerpc mpc8xx netta2
+	@$(MKCONFIG) -n $@ -a NETTA2 powerpc mpc8xx netta2
 
 NC650_Rev1_config \
 NC650_Rev2_config \
@@ -964,34 +952,34 @@ CP850_config:	unconfig
 	@$(MKCONFIG) -n $@ -a NC650 powerpc mpc8xx nc650
 
 NX823_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx nx823
+	@$(MKCONFIG) $@ powerpc mpc8xx nx823
 
 pcu_e_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx pcu_e siemens
+	@$(MKCONFIG) $@ powerpc mpc8xx pcu_e siemens
 
 QS850_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx qs850 snmc
+	@$(MKCONFIG) $@ powerpc mpc8xx qs850 snmc
 
 QS823_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx qs850 snmc
+	@$(MKCONFIG) $@ powerpc mpc8xx qs850 snmc
 
 QS860T_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx qs860t snmc
+	@$(MKCONFIG) $@ powerpc mpc8xx qs860t snmc
 
 quantum_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx quantum
+	@$(MKCONFIG) $@ powerpc mpc8xx quantum
 
 R360MPI_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx r360mpi
+	@$(MKCONFIG) $@ powerpc mpc8xx r360mpi
 
 RBC823_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx rbc823
+	@$(MKCONFIG) $@ powerpc mpc8xx rbc823
 
 RPXClassic_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx RPXClassic
+	@$(MKCONFIG) $@ powerpc mpc8xx RPXClassic
 
 RPXlite_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx RPXlite
+	@$(MKCONFIG) $@ powerpc mpc8xx RPXlite
 
 RPXlite_DW_64_config		\
 RPXlite_DW_LCD_config		\
@@ -1013,10 +1001,10 @@ RPXlite_DW_config:	unconfig
 	@$(MKCONFIG) -n $@ -a RPXlite_DW powerpc mpc8xx RPXlite_dw
 
 rmu_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx rmu
+	@$(MKCONFIG) $@ powerpc mpc8xx rmu
 
 RRvision_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx RRvision
+	@$(MKCONFIG) $@ powerpc mpc8xx RRvision
 
 RRvision_LCD_config:	unconfig
 	@mkdir -p $(obj)include
@@ -1025,31 +1013,31 @@ RRvision_LCD_config:	unconfig
 	@$(MKCONFIG) -a RRvision powerpc mpc8xx RRvision
 
 SM850_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx tqm8xx tqc
+	@$(MKCONFIG) $@ powerpc mpc8xx tqm8xx tqc
 
 spc1920_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx spc1920
+	@$(MKCONFIG) $@ powerpc mpc8xx spc1920
 
 SPD823TS_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx spd8xx
+	@$(MKCONFIG) $@ powerpc mpc8xx spd8xx
 
 stxxtc_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx stxxtc stx
+	@$(MKCONFIG) $@ powerpc mpc8xx stxxtc stx
 
 svm_sc8xx_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx svm_sc8xx
+	@$(MKCONFIG) $@ powerpc mpc8xx svm_sc8xx
 
 SXNI855T_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx sixnet
+	@$(MKCONFIG) $@ powerpc mpc8xx sixnet
 
 # EMK MPC8xx based modules
 TOP860_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx top860 emk
+	@$(MKCONFIG) $@ powerpc mpc8xx top860 emk
 
 # Play some tricks for configuration selection
 # Only 855 and 860 boards may come with FEC
 # and only 823 boards may have LCD support
-xtract_8xx = $(subst _LCD,,$(subst _config,,$1))
+xtract_8xx = $(subst _LCD,,$1)
 
 FPS850L_config		\
 FPS860L_config		\
@@ -1083,13 +1071,13 @@ TTTech_config:	unconfig
 	@$(MKCONFIG) -a TQM823L powerpc mpc8xx tqm8xx tqc
 
 uc100_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx uc100
+	@$(MKCONFIG) $@ powerpc mpc8xx uc100
 
 v37_config:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_LCD" >$(obj)include/config.h
 	@echo "#define CONFIG_SHARP_LQ084V1DG21" >>$(obj)include/config.h
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx v37
+	@$(MKCONFIG) $@ powerpc mpc8xx v37
 
 wtk_config:	unconfig
 	@mkdir -p $(obj)include
@@ -1100,53 +1088,52 @@ wtk_config:	unconfig
 #########################################################################
 ## PPC4xx Systems
 #########################################################################
-xtract_4xx = $(subst _25,,$(subst _33,,$(subst _BA,,$(subst _ME,,$(subst _HI,,$(subst _config,,$1))))))
 
 acadia_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx acadia amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx acadia amcc
 
 acadia_nand_config:	unconfig
 	@mkdir -p $(obj)include $(obj)board/amcc/acadia
 	@mkdir -p $(obj)nand_spl/board/amcc/acadia
 	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a acadia powerpc ppc4xx acadia amcc
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/acadia/config.tmp
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) -n $@ -a acadia powerpc ppc4xx acadia amcc
 
 ADCIOP_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx adciop esd
+	@$(MKCONFIG) $@ powerpc ppc4xx adciop esd
 
 alpr_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx alpr prodrive
+	@$(MKCONFIG) $@ powerpc ppc4xx alpr prodrive
 
 AP1000_config:unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx ap1000 amirix
+	@$(MKCONFIG) $@ powerpc ppc4xx ap1000 amirix
 
 APC405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx apc405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx apc405 esd
 
 AR405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx ar405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx ar405 esd
 
 ASH405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx ash405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx ash405 esd
 
 bamboo_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx bamboo amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx bamboo amcc
 
 bamboo_nand_config:	unconfig
 	@mkdir -p $(obj)include $(obj)board/amcc/bamboo
 	@mkdir -p $(obj)nand_spl/board/amcc/bamboo
 	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a bamboo powerpc ppc4xx bamboo amcc
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/bamboo/config.tmp
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) -n $@ -a bamboo powerpc ppc4xx bamboo amcc
 
 bubinga_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx bubinga amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx bubinga amcc
 
 CANBT_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx canbt esd
+	@$(MKCONFIG) $@ powerpc ppc4xx canbt esd
 
 # Arches, Canyonlands & Glacier use different U-Boot images
 arches_config \
@@ -1178,53 +1165,53 @@ CATcenter_33_config:	unconfig
 		echo "#define CONFIG_PPCHAMELEON_CLK_25" >> $(obj)include/config.h
 	@[ -z "$(findstring _33,$@)" ] || \
 		echo "#define CONFIG_PPCHAMELEON_CLK_33" >> $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_4xx,$@) powerpc ppc4xx PPChameleonEVB dave
+	@$(MKCONFIG) -n $@ -a CATcenter powerpc ppc4xx PPChameleonEVB dave
 
 CMS700_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx cms700 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx cms700 esd
 
 CPCI2DP_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx cpci2dp esd
+	@$(MKCONFIG) $@ powerpc ppc4xx cpci2dp esd
 
 CPCI405_config		\
 CPCI4052_config		\
 CPCI405DT_config	\
 CPCI405AB_config:	unconfig
 	@mkdir -p $(obj)board/esd/cpci405
-	@$(MKCONFIG) -n $@ $(@:_config=) powerpc ppc4xx cpci405 esd
+	@$(MKCONFIG) -n $@ $@ powerpc ppc4xx cpci405 esd
 
 CPCIISER4_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx cpciiser4 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx cpciiser4 esd
 
 CRAYL1_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx L1 cray
+	@$(MKCONFIG) $@ powerpc ppc4xx L1 cray
 
 csb272_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx csb272
+	@$(MKCONFIG) $@ powerpc ppc4xx csb272
 
 csb472_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx csb472
+	@$(MKCONFIG) $@ powerpc ppc4xx csb472
 
 DASA_SIM_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx dasa_sim esd
+	@$(MKCONFIG) $@ powerpc ppc4xx dasa_sim esd
 
 dlvision_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx dlvision gdsys
+	@$(MKCONFIG) $@ powerpc ppc4xx dlvision gdsys
 
 DP405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx dp405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx dp405 esd
 
 DU405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx du405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx du405 esd
 
 DU440_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx du440 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx du440 esd
 
 ebony_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx ebony amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx ebony amcc
 
 ERIC_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx eric
+	@$(MKCONFIG) $@ powerpc ppc4xx eric
 
 fx12mm_flash_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc405-generic
@@ -1245,27 +1232,27 @@ fx12mm_config: unconfig
 	@$(MKCONFIG) fx12mm powerpc ppc4xx fx12mm avnet
 
 G2000_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx g2000
+	@$(MKCONFIG) $@ powerpc ppc4xx g2000
 
 gdppc440etx_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx gdppc440etx gdsys
+	@$(MKCONFIG) $@ powerpc ppc4xx gdppc440etx gdsys
 
 hcu4_config:	unconfig
 	@mkdir -p $(obj)board/netstal/common
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx hcu4 netstal
+	@$(MKCONFIG) $@ powerpc ppc4xx hcu4 netstal
 
 hcu5_config:	unconfig
 	@mkdir -p $(obj)board/netstal/common
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx hcu5 netstal
+	@$(MKCONFIG) $@ powerpc ppc4xx hcu5 netstal
 
 HH405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx hh405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx hh405 esd
 
 HUB405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx hub405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx hub405 esd
 
 icon_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx icon mosaixtech
+	@$(MKCONFIG) $@ powerpc ppc4xx icon mosaixtech
 
 # Compact-Center(codename intip) & DevCon-Center use different U-Boot images
 intip_config \
@@ -1276,18 +1263,18 @@ devconcenter_config:	unconfig
 	@$(MKCONFIG) -n $@ -a intip powerpc ppc4xx intip gdsys
 
 JSE_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx jse
+	@$(MKCONFIG) $@ powerpc ppc4xx jse
 
 KAREF_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx karef sandburst
+	@$(MKCONFIG) $@ powerpc ppc4xx karef sandburst
 
 katmai_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx katmai amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx katmai amcc
 
 # Kilauea & Haleakala images are identical (recognized via PVR)
 kilauea_config \
 haleakala_config: unconfig
-	@$(MKCONFIG) -n $@ -a kilauea powerpc ppc4xx kilauea amcc
+	@$(MKCONFIG) -n $@ kilauea powerpc ppc4xx kilauea amcc
 
 kilauea_nand_config \
 haleakala_nand_config: unconfig
@@ -1299,26 +1286,26 @@ haleakala_nand_config: unconfig
 	@$(MKCONFIG) -n $@ -a kilauea powerpc ppc4xx kilauea amcc
 
 korat_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx korat
+	@$(MKCONFIG) $@ powerpc ppc4xx korat
 
 luan_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx luan amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx luan amcc
 
 lwmon5_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx lwmon5
+	@$(MKCONFIG) $@ powerpc ppc4xx lwmon5
 
 makalu_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx makalu amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx makalu amcc
 
 mcu25_config:  unconfig
 	@mkdir -p $(obj)board/netstal/common
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx mcu25 netstal
+	@$(MKCONFIG) $@ powerpc ppc4xx mcu25 netstal
 
 METROBOX_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx metrobox sandburst
+	@$(MKCONFIG) $@ powerpc ppc4xx metrobox sandburst
 
 MIP405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx mip405 mpl
+	@$(MKCONFIG) $@ powerpc ppc4xx mip405 mpl
 
 MIP405T_config:	unconfig
 	@mkdir -p $(obj)include
@@ -1327,7 +1314,7 @@ MIP405T_config:	unconfig
 	@$(MKCONFIG) -a MIP405 powerpc ppc4xx mip405 mpl
 
 ML2_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx ml2
+	@$(MKCONFIG) $@ powerpc ppc4xx ml2
 
 ml507_flash_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
@@ -1345,41 +1332,41 @@ ml507_config: unconfig
 		> $(obj)board/xilinx/ml507/config.tmp
 	@echo "TEXT_BASE := 0x04000000"  \
 		>> $(obj)board/xilinx/ml507/config.tmp
-	@$(MKCONFIG) ml507 powerpc ppc4xx ml507 xilinx
+	@$(MKCONFIG) $@ powerpc ppc4xx ml507 xilinx
 
 neo_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx neo gdsys
+	@$(MKCONFIG) $@ powerpc ppc4xx neo gdsys
 
 ocotea_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx ocotea amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx ocotea amcc
 
 OCRTC_config		\
 ORSG_config:	unconfig
-	@$(MKCONFIG) -n $@ $(@:_config=) powerpc ppc4xx ocrtc esd
+	@$(MKCONFIG) -n $@ $@ powerpc ppc4xx ocrtc esd
 
 p3p440_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx p3p440 prodrive
+	@$(MKCONFIG) $@ powerpc ppc4xx p3p440 prodrive
 
 PCI405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx pci405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx pci405 esd
 
 pcs440ep_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx pcs440ep
+	@$(MKCONFIG) $@ powerpc ppc4xx pcs440ep
 
 PIP405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx pip405 mpl
+	@$(MKCONFIG) $@ powerpc ppc4xx pip405 mpl
 
 PLU405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx plu405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx plu405 esd
 
 PMC405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx pmc405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx pmc405 esd
 
 PMC405DE_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx pmc405de esd
+	@$(MKCONFIG) $@ powerpc ppc4xx pmc405de esd
 
 PMC440_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx pmc440 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx pmc440 esd
 
 PPChameleonEVB_config		\
 PPChameleonEVB_BA_25_config	\
@@ -1399,19 +1386,19 @@ PPChameleonEVB_HI_33_config:	unconfig
 		echo "#define CONFIG_PPCHAMELEON_CLK_25" >>$(obj)include/config.h
 	@[ -z "$(findstring _33,$@)" ] || \
 		echo "#define CONFIG_PPCHAMELEON_CLK_33" >>$(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a $(call xtract_4xx,$@) powerpc ppc4xx PPChameleonEVB dave
+	@$(MKCONFIG) -n $@ -a PPChameleonEVB powerpc ppc4xx PPChameleonEVB dave
 
 quad100hd_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx quad100hd
+	@$(MKCONFIG) $@ powerpc ppc4xx quad100hd
 
 redwood_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx redwood amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx redwood amcc
 
 sbc405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx sbc405
+	@$(MKCONFIG) $@ powerpc ppc4xx sbc405
 
 sc3_config:unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx sc3
+	@$(MKCONFIG) $@ powerpc ppc4xx sc3
 
 sequoia_config \
 rainier_config: unconfig
@@ -1443,10 +1430,10 @@ rainier_ramboot_config: unconfig
 	@$(MKCONFIG) -n $@ -a sequoia powerpc ppc4xx sequoia amcc
 
 taihu_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx taihu amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx taihu amcc
 
 taishan_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx taishan amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx taishan amcc
 
 v5fx30teval_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
@@ -1455,7 +1442,7 @@ v5fx30teval_config: unconfig
 		> $(obj)board/avnet/v5fx30teval/config.tmp
 	@echo "TEXT_BASE := 0x03000000" \
 		>> $(obj)board/avnet/v5fx30teval/config.tmp
-	@$(MKCONFIG) v5fx30teval powerpc ppc4xx v5fx30teval avnet
+	@$(MKCONFIG) $@ powerpc ppc4xx v5fx30teval avnet
 
 v5fx30teval_flash_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
@@ -1467,22 +1454,22 @@ v5fx30teval_flash_config: unconfig
 	@$(MKCONFIG) v5fx30teval powerpc ppc4xx v5fx30teval avnet
 
 VOH405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx voh405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx voh405 esd
 
 VOM405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx vom405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx vom405 esd
 
 W7OLMC_config	\
 W7OLMG_config: unconfig
-	@$(MKCONFIG) -n $@ $(@:_config=) powerpc ppc4xx w7o
+	@$(MKCONFIG) $@ powerpc ppc4xx w7o
 
 # Walnut & Sycamore images are identical (recognized via PVR)
 walnut_config \
 sycamore_config: unconfig
-	@$(MKCONFIG) -n $@ -a walnut powerpc ppc4xx walnut amcc
+	@$(MKCONFIG) -n $@ walnut powerpc ppc4xx walnut amcc
 
 WUH405_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx wuh405 esd
+	@$(MKCONFIG) $@ powerpc ppc4xx wuh405 esd
 
 xilinx-ppc405-generic_flash_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc405-generic
@@ -1517,7 +1504,7 @@ xilinx-ppc440-generic_config: unconfig
 	@$(MKCONFIG) xilinx-ppc440-generic powerpc ppc4xx ppc440-generic xilinx
 
 XPEDITE1000_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx xpedite1000 xes
+	@$(MKCONFIG) $@ powerpc ppc4xx xpedite1000 xes
 
 yosemite_config \
 yellowstone_config: unconfig
@@ -1527,10 +1514,10 @@ yellowstone_config: unconfig
 	@$(MKCONFIG) -n $@ -a yosemite powerpc ppc4xx yosemite amcc
 
 yucca_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx yucca amcc
+	@$(MKCONFIG) $@ powerpc ppc4xx yucca amcc
 
 zeus_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc ppc4xx zeus
+	@$(MKCONFIG) $@ powerpc ppc4xx zeus
 
 #########################################################################
 ## MPC8220 Systems
@@ -1538,24 +1525,23 @@ zeus_config:	unconfig
 
 Alaska8220_config	\
 Yukon8220_config:	unconfig
-	@$(MKCONFIG) -n $@ $(@:_config=) powerpc mpc8220 alaska
+	@$(MKCONFIG) $@ powerpc mpc8220 alaska
 
 sorcery_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8220 sorcery
+	@$(MKCONFIG) $@ powerpc mpc8220 sorcery
 
 #########################################################################
 ## MPC824x Systems
 #########################################################################
-xtract_82xx = $(subst _BIGFLASH,,$(subst _ROMBOOT,,$(subst _L2,,$(subst _266MHz,,$(subst _300MHz,,$(subst _config,,$1))))))
 
 A3000_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x a3000
+	@$(MKCONFIG) $@ powerpc mpc824x a3000
 
 barco_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x barco
+	@$(MKCONFIG) $@ powerpc mpc824x barco
 
 BMW_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x bmw
+	@$(MKCONFIG) $@ powerpc mpc824x bmw
 
 CPC45_config	\
 CPC45_ROMBOOT_config:	unconfig
@@ -1566,22 +1552,22 @@ CPC45_ROMBOOT_config:	unconfig
 		echo "CONFIG_BOOT_ROM = n" >> $(obj)include/config.mk ; \
 	fi; \
 	echo "export CONFIG_BOOT_ROM" >> $(obj)include/config.mk;
-	@$(MKCONFIG) -n $@ $(call xtract_82xx,$@) powerpc mpc824x cpc45
+	@$(MKCONFIG) -n $@ CPC45 powerpc mpc824x cpc45
 
 CU824_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x cu824
+	@$(MKCONFIG) $@ powerpc mpc824x cu824
 
 debris_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x debris etin
+	@$(MKCONFIG) $@ powerpc mpc824x debris etin
 
 eXalion_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x eXalion
+	@$(MKCONFIG) $@ powerpc mpc824x eXalion
 
 HIDDEN_DRAGON_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x hidden_dragon
+	@$(MKCONFIG) $@ powerpc mpc824x hidden_dragon
 
 kvme080_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x kvme080 etin
+	@$(MKCONFIG) $@ powerpc mpc824x kvme080 etin
 
 # HDLAN is broken ATM. Should be fixed as soon as hardware is available and as
 # time permits.
@@ -1596,41 +1582,41 @@ linkstation_HGLAN_config: unconfig
 	@$(MKCONFIG) -n $@ -a linkstation powerpc mpc824x linkstation
 
 MOUSSE_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x mousse
+	@$(MKCONFIG) $@ powerpc mpc824x mousse
 
 MUSENKI_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x musenki
+	@$(MKCONFIG) $@ powerpc mpc824x musenki
 
 MVBLUE_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x mvblue
+	@$(MKCONFIG) $@ powerpc mpc824x mvblue
 
 OXC_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x oxc
+	@$(MKCONFIG) $@ powerpc mpc824x oxc
 
 PN62_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x pn62
+	@$(MKCONFIG) $@ powerpc mpc824x pn62
 
 Sandpoint8240_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x sandpoint
+	@$(MKCONFIG) $@ powerpc mpc824x sandpoint
 
 Sandpoint8245_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x sandpoint
+	@$(MKCONFIG) $@ powerpc mpc824x sandpoint
 
 sbc8240_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x sbc8240
+	@$(MKCONFIG) $@ powerpc mpc824x sbc8240
 
 utx8245_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc824x utx8245
+	@$(MKCONFIG) $@ powerpc mpc824x utx8245
 
 #########################################################################
 ## MPC8260 Systems
 #########################################################################
 
 atc_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 atc
+	@$(MKCONFIG) $@ powerpc mpc8260 atc
 
 cogent_mpc8260_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 cogent
+	@$(MKCONFIG) $@ powerpc mpc8260 cogent
 
 CPU86_config	\
 CPU86_ROMBOOT_config: unconfig
@@ -1641,7 +1627,7 @@ CPU86_ROMBOOT_config: unconfig
 		echo "CONFIG_BOOT_ROM = n" >> $(obj)include/config.mk ; \
 	fi; \
 	echo "export CONFIG_BOOT_ROM" >> $(obj)include/config.mk;
-	@$(MKCONFIG) -n $@ $(call xtract_82xx,$@) powerpc mpc8260 cpu86
+	@$(MKCONFIG) -n $@ CPU86 powerpc mpc8260 cpu86
 
 CPU87_config	\
 CPU87_ROMBOOT_config: unconfig
@@ -1652,29 +1638,29 @@ CPU87_ROMBOOT_config: unconfig
 		echo "CONFIG_BOOT_ROM = n" >> $(obj)include/config.mk ; \
 	fi; \
 	echo "export CONFIG_BOOT_ROM" >> $(obj)include/config.mk;
-	@$(MKCONFIG) -n $@ $(call xtract_82xx,$@) powerpc mpc8260 cpu87
+	@$(MKCONFIG) -n $@ CPU87 powerpc mpc8260 cpu87
 
 ep8248_config	\
 ep8248E_config	:	unconfig
 	@$(MKCONFIG) -n $@ ep8248 powerpc mpc8260 ep8248
 
 ep8260_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 ep8260
+	@$(MKCONFIG) $@ powerpc mpc8260 ep8260
 
 ep82xxm_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 ep82xxm
+	@$(MKCONFIG) $@ powerpc mpc8260 ep82xxm
 
 gw8260_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 gw8260
+	@$(MKCONFIG) $@ powerpc mpc8260 gw8260
 
 hymod_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 hymod
+	@$(MKCONFIG) $@ powerpc mpc8260 hymod
 
 IDS8247_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 ids8247
+	@$(MKCONFIG) $@ powerpc mpc8260 ids8247
 
 IPHASE4539_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 iphase4539
+	@$(MKCONFIG) $@ powerpc mpc8260 iphase4539
 
 ISPAN_config		\
 ISPAN_REVB_config:	unconfig
@@ -1685,7 +1671,7 @@ ISPAN_REVB_config:	unconfig
 	@$(MKCONFIG) -n $@ -a ISPAN powerpc mpc8260 ispan
 
 mgcoge_config	:	unconfig
-	@$(MKCONFIG) mgcoge powerpc mpc8260 mgcoge keymile
+	@$(MKCONFIG) $@ powerpc mpc8260 mgcoge keymile
 
 MPC8260ADS_config	\
 MPC8260ADS_lowboot_config	\
@@ -1718,7 +1704,7 @@ PQ2FADS-ZU_66MHz_lowboot_config	\
 	@$(MKCONFIG) -n $@ -a MPC8260ADS powerpc mpc8260 mpc8260ads freescale
 
 MPC8266ADS_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 mpc8266ads freescale
+	@$(MKCONFIG) $@ powerpc mpc8260 mpc8266ads freescale
 
 muas3001_dev_config \
 muas3001_config	:	unconfig
@@ -1778,7 +1764,7 @@ PM828_ROMBOOT_PCI_config:	unconfig
 	@$(MKCONFIG) -n $@ -a PM828 powerpc mpc8260 pm828
 
 ppmc8260_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 ppmc8260
+	@$(MKCONFIG) $@ powerpc mpc8260 ppmc8260
 
 Rattler8248_config	\
 Rattler_config:		unconfig
@@ -1788,19 +1774,19 @@ Rattler_config:		unconfig
 	@$(MKCONFIG) -n $@ -a Rattler powerpc mpc8260 rattler
 
 RPXsuper_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 rpxsuper
+	@$(MKCONFIG) $@ powerpc mpc8260 rpxsuper
 
 rsdproto_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 rsdproto
+	@$(MKCONFIG) $@ powerpc mpc8260 rsdproto
 
 sacsng_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 sacsng
+	@$(MKCONFIG) $@ powerpc mpc8260 sacsng
 
 sbc8260_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 sbc8260
+	@$(MKCONFIG) $@ powerpc mpc8260 sbc8260
 
 SCM_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 SCM siemens
+	@$(MKCONFIG) $@ powerpc mpc8260 SCM siemens
 
 TQM8255_AA_config \
 TQM8260_AA_config \
@@ -1853,7 +1839,7 @@ VoVPN-GW_100MHz_config:		unconfig
 	@$(MKCONFIG) -n $@ -a VoVPN-GW powerpc mpc8260 vovpn-gw funkwerk
 
 ZPC1900_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 zpc1900
+	@$(MKCONFIG) $@ powerpc mpc8260 zpc1900
 
 #########################################################################
 ## Coldfire
@@ -1861,10 +1847,10 @@ ZPC1900_config: unconfig
 
 astro_mcf5373l_config \
 astro_mcf5373l_RAM_config :	unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) astro_mcf5373l m68k mcf532x mcf5373l astro
+	@$(MKCONFIG) -n $@ -t $@ astro_mcf5373l m68k mcf532x mcf5373l astro
 
 M5208EVBE_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5208evbe freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5208evbe freescale
 
 M52277EVB_config \
 M52277EVB_spansion_config \
@@ -1906,16 +1892,16 @@ M5235EVB_Flash32_config:	unconfig
 	@$(MKCONFIG) -n $@ -a M5235EVB m68k mcf523x m5235evb freescale
 
 M5249EVB_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5249evb freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5249evb freescale
 
 M5253DEMO_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5253demo freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5253demo freescale
 
 M5253EVBE_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5253evbe freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5253evbe freescale
 
 cobra5272_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 cobra5272
+	@$(MKCONFIG) $@ m68k mcf52x2 cobra5272
 
 EB+MCF-EV123_config :		unconfig
 	@mkdir -p $(obj)include
@@ -1930,25 +1916,25 @@ EB+MCF-EV123_internal_config :	unconfig
 	@$(MKCONFIG) -n $@ EB+MCF-EV123 m68k mcf52x2 EB+MCF-EV123 BuS
 
 EP2500_config:			unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 ep2500 Mercury
+	@$(MKCONFIG) $@ m68k mcf52x2 ep2500 Mercury
 
 idmr_config :			unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 idmr
+	@$(MKCONFIG) $@ m68k mcf52x2 idmr
 
 M5271EVB_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5271evb freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5271evb freescale
 
 M5272C3_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5272c3 freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5272c3 freescale
 
 M5275EVB_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5275evb freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5275evb freescale
 
 M5282EVB_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 m5282evb freescale
+	@$(MKCONFIG) $@ m68k mcf52x2 m5282evb freescale
 
 M53017EVB_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf532x m53017evb freescale
+	@$(MKCONFIG) $@ m68k mcf532x m53017evb freescale
 
 M5329AFEE_config \
 M5329BFEE_config :	unconfig
@@ -2095,7 +2081,7 @@ M5485HFE_config :	unconfig
 	@$(MKCONFIG) -n $@ -a M5485EVB m68k mcf547x_8x m548xevb freescale
 
 TASREG_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) m68k mcf52x2 tasreg esd
+	@$(MKCONFIG) $@ m68k mcf52x2 tasreg esd
 
 #########################################################################
 ## MPC83xx Systems
@@ -2127,10 +2113,10 @@ MPC8313ERDB_NAND_66_config: unconfig
 
 MPC8315ERDB_NAND_config \
 MPC8315ERDB_config: unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8315ERDB powerpc mpc83xx mpc8315erdb freescale
+	@$(MKCONFIG) -n $@ -t $@ MPC8315ERDB powerpc mpc83xx mpc8315erdb freescale
 
 MPC8323ERDB_config:	unconfig
-	@$(MKCONFIG) -a MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale
+	@$(MKCONFIG) $@ powerpc mpc83xx mpc8323erdb freescale
 
 MPC832XEMDS_config \
 MPC832XEMDS_HOST_33_config \
@@ -2160,7 +2146,7 @@ MPC832XEMDS_ATM_config:	unconfig
 	@$(MKCONFIG) -n $@ -a MPC832XEMDS powerpc mpc83xx mpc832xemds freescale
 
 MPC8349EMDS_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc83xx mpc8349emds freescale
+	@$(MKCONFIG) $@ powerpc mpc83xx mpc8349emds freescale
 
 MPC8349ITX_config \
 MPC8349ITX_LOWBOOT_config \
@@ -2221,15 +2207,15 @@ MPC837XEMDS_HOST_config:	unconfig
 	@$(MKCONFIG) -n $@ -a MPC837XEMDS powerpc mpc83xx mpc837xemds freescale
 
 MPC837XERDB_config:	unconfig
-	@$(MKCONFIG) -a MPC837XERDB powerpc mpc83xx mpc837xerdb freescale
+	@$(MKCONFIG) $@ powerpc mpc83xx mpc837xerdb freescale
 
 MVBLM7_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc83xx mvblm7 matrix_vision
+	@$(MKCONFIG) $@ powerpc mpc83xx mvblm7 matrix_vision
 
 sbc8349_config \
 sbc8349_PCI_33_config \
 sbc8349_PCI_66_config: unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) sbc8349 powerpc mpc83xx sbc8349
+	@$(MKCONFIG) -n $@ -t $@ sbc8349 powerpc mpc83xx sbc8349
 
 SIMPC8313_LP_config \
 SIMPC8313_SP_config: unconfig
@@ -2245,11 +2231,11 @@ SIMPC8313_SP_config: unconfig
 	@$(MKCONFIG) -n $@ -a SIMPC8313 powerpc mpc83xx simpc8313 sheldon
 
 TQM834x_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc83xx tqm834x tqc
+	@$(MKCONFIG) $@ powerpc mpc83xx tqm834x tqc
 
 caddy2_config \
 vme8349_config:		unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) vme8349 powerpc mpc83xx vme8349 esd
+	@$(MKCONFIG) -n $@ -t $@ vme8349 powerpc mpc83xx vme8349 esd
 
 edb9301_config \
 edb9302_config \
@@ -2259,24 +2245,24 @@ edb9307a_config \
 edb9312_config \
 edb9315_config \
 edb9315a_config: unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) edb93xx arm arm920t edb93xx NULL ep93xx
+	@$(MKCONFIG) -n $@ -t $@ edb93xx arm arm920t edb93xx NULL ep93xx
 
 #########################################################################
 ## MPC85xx Systems
 #########################################################################
 
 ATUM8548_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx atum8548
+	@$(MKCONFIG) $@ powerpc mpc85xx atum8548
 
 MPC8536DS_NAND_config \
 MPC8536DS_SDCARD_config \
 MPC8536DS_SPIFLASH_config \
 MPC8536DS_36BIT_config \
 MPC8536DS_config:       unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8536DS powerpc mpc85xx mpc8536ds freescale
+	@$(MKCONFIG) -n $@ -t $@ MPC8536DS powerpc mpc85xx mpc8536ds freescale
 
 MPC8540ADS_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8540ads freescale
+	@$(MKCONFIG) $@ powerpc mpc85xx mpc8540ads freescale
 
 MPC8540EVAL_config \
 MPC8540EVAL_33_config \
@@ -2293,7 +2279,7 @@ MPC8540EVAL_66_slave_config:	unconfig
 	@$(MKCONFIG) -n $@ -a MPC8540EVAL powerpc mpc85xx mpc8540eval
 
 MPC8560ADS_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8560ads freescale
+	@$(MKCONFIG) $@ powerpc mpc85xx mpc8560ads freescale
 
 MPC8541CDS_legacy_config \
 MPC8541CDS_config:	unconfig
@@ -2304,7 +2290,7 @@ MPC8541CDS_config:	unconfig
 	@$(MKCONFIG) -n $@ -a MPC8541CDS powerpc mpc85xx mpc8541cds freescale
 
 MPC8544DS_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8544ds freescale
+	@$(MKCONFIG) $@ powerpc mpc85xx mpc8544ds freescale
 
 MPC8548CDS_legacy_config \
 MPC8548CDS_config:	unconfig
@@ -2323,20 +2309,20 @@ MPC8555CDS_config:	unconfig
 	@$(MKCONFIG) -n $@ -a MPC8555CDS powerpc mpc85xx mpc8555cds freescale
 
 MPC8568MDS_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx mpc8568mds freescale
+	@$(MKCONFIG) $@ powerpc mpc85xx mpc8568mds freescale
 
 MPC8569MDS_ATM_config \
 MPC8569MDS_NAND_config \
 MPC8569MDS_config:	unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8569MDS powerpc mpc85xx mpc8569mds freescale
+	@$(MKCONFIG) -n $@ -t $@ MPC8569MDS powerpc mpc85xx mpc8569mds freescale
 
 MPC8572DS_36BIT_config \
 MPC8572DS_config:       unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) MPC8572DS powerpc mpc85xx mpc8572ds freescale
+	@$(MKCONFIG) -n $@ -t $@ MPC8572DS powerpc mpc85xx mpc8572ds freescale
 
 P2020DS_36BIT_config \
 P2020DS_config:		unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) P2020DS powerpc mpc85xx p2020ds freescale
+	@$(MKCONFIG) -n $@ -t $@ P2020DS powerpc mpc85xx p2020ds freescale
 
 P1011RDB_config	\
 P1011RDB_NAND_config \
@@ -2354,36 +2340,36 @@ P2020RDB_config \
 P2020RDB_NAND_config \
 P2020RDB_SDCARD_config \
 P2020RDB_SPIFLASH_config:	unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) P1_P2_RDB powerpc mpc85xx p1_p2_rdb freescale
+	@$(MKCONFIG) -n $@ -t $@ P1_P2_RDB powerpc mpc85xx p1_p2_rdb freescale
 
 PM854_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx pm854
+	@$(MKCONFIG) $@ powerpc mpc85xx pm854
 
 PM856_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx pm856
+	@$(MKCONFIG) $@ powerpc mpc85xx pm856
 
 sbc8540_config \
 sbc8540_33_config \
 sbc8540_66_config:	unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) SBC8540 powerpc mpc85xx sbc8560
+	@$(MKCONFIG) -n $@ -t $@ SBC8540 powerpc mpc85xx sbc8560
 
 sbc8548_config \
 sbc8548_PCI_33_config \
 sbc8548_PCI_66_config \
 sbc8548_PCI_33_PCIE_config \
 sbc8548_PCI_66_PCIE_config: unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) sbc8548 powerpc mpc85xx sbc8548
+	@$(MKCONFIG) -n $@ -t $@ sbc8548 powerpc mpc85xx sbc8548
 
 sbc8560_config \
 sbc8560_33_config \
 sbc8560_66_config:	unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) sbc8560 powerpc mpc85xx sbc8560
+	@$(MKCONFIG) -n $@ -t $@ sbc8560 powerpc mpc85xx sbc8560
 
 socrates_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx socrates
+	@$(MKCONFIG) $@ powerpc mpc85xx socrates
 
 stxgp3_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx stxgp3 stx
+	@$(MKCONFIG) $@ powerpc mpc85xx stxgp3 stx
 
 stxssa_config		\
 stxssa_4M_config:	unconfig
@@ -2411,17 +2397,17 @@ TQM8560_config:		unconfig
 	@$(MKCONFIG) -n $@ -a TQM85xx powerpc mpc85xx tqm85xx tqc
 
 XPEDITE5200_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx xpedite5200 xes
+	@$(MKCONFIG) $@ powerpc mpc85xx xpedite5200 xes
 
 XPEDITE5370_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc85xx xpedite5370 xes
+	@$(MKCONFIG) $@ powerpc mpc85xx xpedite5370 xes
 
 #########################################################################
 ## MPC86xx Systems
 #########################################################################
 
 MPC8610HPCD_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc86xx mpc8610hpcd freescale
+	@$(MKCONFIG) $@ powerpc mpc86xx mpc8610hpcd freescale
 
 MPC8641HPCN_36BIT_config \
 MPC8641HPCN_config:    unconfig
@@ -2432,42 +2418,42 @@ MPC8641HPCN_config:    unconfig
 	@$(MKCONFIG) -n $@ -a MPC8641HPCN powerpc mpc86xx mpc8641hpcn freescale
 
 sbc8641d_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc86xx sbc8641d
+	@$(MKCONFIG) $@ powerpc mpc86xx sbc8641d
 
 XPEDITE5170_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc86xx xpedite5170 xes
+	@$(MKCONFIG) $@ powerpc mpc86xx xpedite5170 xes
 
 #########################################################################
 ## 74xx/7xx Systems
 #########################################################################
 
 AmigaOneG3SE_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx AmigaOneG3SE MAI
+	@$(MKCONFIG) $@ powerpc 74xx_7xx AmigaOneG3SE MAI
 
 BAB7xx_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx bab7xx eltec
+	@$(MKCONFIG) $@ powerpc 74xx_7xx bab7xx eltec
 
 CPCI750_config:	unconfig
-	@$(MKCONFIG) CPCI750 powerpc 74xx_7xx cpci750 esd
+	@$(MKCONFIG) $@ powerpc 74xx_7xx cpci750 esd
 
 DB64360_config:	unconfig
-	@$(MKCONFIG) DB64360 powerpc 74xx_7xx db64360 Marvell
+	@$(MKCONFIG) $@ powerpc 74xx_7xx db64360 Marvell
 
 DB64460_config:	unconfig
-	@$(MKCONFIG) DB64460 powerpc 74xx_7xx db64460 Marvell
+	@$(MKCONFIG) $@ powerpc 74xx_7xx db64460 Marvell
 
 ELPPC_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx elppc eltec
+	@$(MKCONFIG) $@ powerpc 74xx_7xx elppc eltec
 
 EVB64260_config	\
 EVB64260_750CX_config:	unconfig
 	@$(MKCONFIG) -n $@ EVB64260 powerpc 74xx_7xx evb64260
 
 mpc7448hpc2_config:  unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx mpc7448hpc2 freescale
+	@$(MKCONFIG) $@ powerpc 74xx_7xx mpc7448hpc2 freescale
 
 P3G4_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx evb64260
+	@$(MKCONFIG) $@ powerpc 74xx_7xx evb64260
 
 p3m750_config	\
 p3m7448_config:		unconfig
@@ -2481,13 +2467,13 @@ p3m7448_config:		unconfig
 
 PCIPPC2_config \
 PCIPPC6_config: unconfig
-	@$(MKCONFIG) -n $@ $(@:_config=) powerpc 74xx_7xx pcippc2
+	@$(MKCONFIG) -n $@ $@ powerpc 74xx_7xx pcippc2
 
 ppmc7xx_config: unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx ppmc7xx
+	@$(MKCONFIG) $@ powerpc 74xx_7xx ppmc7xx
 
 ZUMA_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc 74xx_7xx evb64260
+	@$(MKCONFIG) $@ powerpc 74xx_7xx evb64260
 
 #========================================================================
 # ARM
@@ -2497,39 +2483,39 @@ ZUMA_config:	unconfig
 #########################################################################
 
 assabet_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm sa1100 assabet
+	@$(MKCONFIG) $@ arm sa1100 assabet
 
 dnp1110_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm sa1100 dnp1110
+	@$(MKCONFIG) $@ arm sa1100 dnp1110
 
 gcplus_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm sa1100 gcplus
+	@$(MKCONFIG) $@ arm sa1100 gcplus
 
 lart_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm sa1100 lart
+	@$(MKCONFIG) $@ arm sa1100 lart
 
 shannon_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm sa1100 shannon
+	@$(MKCONFIG) $@ arm sa1100 shannon
 
 #########################################################################
 ## ARM92xT Systems
 #########################################################################
 
 a320evb_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t a320evb faraday a320
+	@$(MKCONFIG) $@ arm arm920t a320evb faraday a320
 
 #########################################################################
 ## Atmel AT91RM9200 Systems
 #########################################################################
 
 at91rm9200dk_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t at91rm9200dk atmel at91rm9200
+	@$(MKCONFIG) $@ arm arm920t at91rm9200dk atmel at91rm9200
 
 at91rm9200ek_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t at91rm9200ek atmel at91rm9200
+	@$(MKCONFIG) $@ arm arm920t at91rm9200ek atmel at91rm9200
 
 cmc_pu2_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t cmc_pu2 NULL at91rm9200
+	@$(MKCONFIG) $@ arm arm920t cmc_pu2 NULL at91rm9200
 
 CPUAT91_RAM_config \
 CPUAT91_config	:	unconfig
@@ -2538,29 +2524,29 @@ CPUAT91_config	:	unconfig
 	@$(MKCONFIG) -n $@ -a cpuat91 arm arm920t cpuat91 eukrea at91rm9200
 
 csb637_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t csb637 NULL at91rm9200
+	@$(MKCONFIG) $@ arm arm920t csb637 NULL at91rm9200
 
 eb_cpux9k2_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t eb_cpux9k2 BuS at91
+	@$(MKCONFIG) $@ arm arm920t eb_cpux9k2 BuS at91
 
 kb9202_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t kb9202 NULL at91rm9200
+	@$(MKCONFIG) $@ arm arm920t kb9202 NULL at91rm9200
 
 m501sk_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t m501sk NULL at91rm9200
+	@$(MKCONFIG) $@ arm arm920t m501sk NULL at91rm9200
 
 mp2usb_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t mp2usb NULL at91rm9200
+	@$(MKCONFIG) $@ arm arm920t mp2usb NULL at91rm9200
 
 #########################################################################
 ## ARM926EJ-S Systems
 #########################################################################
 
 afeb9260_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs afeb9260 NULL at91
+	@$(MKCONFIG) $@ arm arm926ejs afeb9260 NULL at91
 
 at91cap9adk_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs at91cap9adk atmel at91
+	@$(MKCONFIG) $@ arm arm926ejs at91cap9adk atmel at91
 
 at91sam9260ek_nandflash_config \
 at91sam9260ek_dataflash_cs0_config \
@@ -2662,10 +2648,10 @@ CPU9260_config	:	unconfig
 	@$(MKCONFIG) -n $@ -a cpu9260 arm arm926ejs cpu9260 eukrea at91
 
 meesc_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs meesc esd at91
+	@$(MKCONFIG) $@ arm arm926ejs meesc esd at91
 
 pm9261_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs pm9261 ronetix at91
+	@$(MKCONFIG) $@ arm arm926ejs pm9261 ronetix at91
 
 at91sam9m10g45ek_nandflash_config \
 at91sam9m10g45ek_dataflash_config \
@@ -2689,10 +2675,10 @@ at91sam9g45ekes_config	:	unconfig
 	@$(MKCONFIG) -n $@ -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91
 
 otc570_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs otc570 esd at91
+	@$(MKCONFIG) $@ arm arm926ejs otc570 esd at91
 
 pm9263_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91
+	@$(MKCONFIG) $@ arm arm926ejs pm9263 ronetix at91
 
 SBC35_A9G20_NANDFLASH_config \
 SBC35_A9G20_EEPROM_config \
@@ -2746,31 +2732,31 @@ davinci_dm355evm_config		\
 davinci_dm355leopard_config	\
 davinci_dm365evm_config		\
 davinci_dm6467evm_config	:	unconfig
-	@$(MKCONFIG) -n $@ $(@:_config=) arm arm926ejs \
+	@$(MKCONFIG) -n $@ $@ arm arm926ejs \
 		$(subst davinci_,,$(@:_config=)) davinci davinci
 
 guruplug_config: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
 
 magnesium_config	\
 imx27lite_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs imx27lite logicpd mx27
+	@$(MKCONFIG) $@ arm arm926ejs imx27lite logicpd mx27
 
 lpd7a400_config \
 lpd7a404_config:	unconfig
-	@$(MKCONFIG) -n $(@:_config=) arm lh7a40x lpd7a40x
+	@$(MKCONFIG) $@ arm lh7a40x lpd7a40x
 
 mv88f6281gtw_ge_config: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
 
 mx1ads_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t mx1ads NULL imx
+	@$(MKCONFIG) $@ arm arm920t mx1ads NULL imx
 
 mx1fs2_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t mx1fs2 NULL imx
+	@$(MKCONFIG) $@ arm arm920t mx1fs2 NULL imx
 
 netstar_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm925t netstar
+	@$(MKCONFIG) $@ arm arm925t netstar
 
 nhk8815_config \
 nhk8815_onenand_config:	unconfig
@@ -2782,7 +2768,7 @@ nhk8815_onenand_config:	unconfig
 	@$(MKCONFIG) -n $@ -a nhk8815 arm arm926ejs nhk8815 st nomadik
 
 omap1510inn_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm925t omap1510inn ti
+	@$(MKCONFIG) $@ arm arm925t omap1510inn ti
 
 xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,,$(subst _cs_autoboot,,$(subst _config,,$1))))
 
@@ -2805,12 +2791,10 @@ omap1610h2_cs_autoboot_config:	unconfig
 	@$(MKCONFIG) -n $@ -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn ti omap
 
 omap5912osk_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
+	@$(MKCONFIG) $@ arm arm926ejs omap5912osk ti omap
 
 openrd_base_config: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
-
-xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
+	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
 
 omap730p2_config \
 omap730p2_cs0boot_config \
@@ -2821,36 +2805,36 @@ omap730p2_cs3boot_config :	unconfig
 	else \
 		echo "#define CONFIG_CS3_BOOT" >> $(obj)include/config.h ; \
 	fi;
-	@$(MKCONFIG) -n $@ -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 ti omap
+	@$(MKCONFIG) -n $@ -a omap730p2 arm arm926ejs omap730p2 ti omap
 
 rd6281a_config: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
 
 sbc2410x_config: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t sbc2410x NULL s3c24x0
+	@$(MKCONFIG) $@ arm arm920t sbc2410x NULL s3c24x0
 
 scb9328_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t scb9328 NULL imx
+	@$(MKCONFIG) $@ arm arm920t scb9328 NULL imx
 
 sheevaplug_config: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
 
 smdk2400_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t smdk2400 samsung s3c24x0
+	@$(MKCONFIG) $@ arm arm920t smdk2400 samsung s3c24x0
 
 smdk2410_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t smdk2410 samsung s3c24x0
+	@$(MKCONFIG) $@ arm arm920t smdk2410 samsung s3c24x0
 
 spear300_config \
 spear310_config \
 spear320_config :	unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) spear3xx arm arm926ejs $(@:_config=) spear spear
+	@$(MKCONFIG) -n $@ -t $@ spear3xx arm arm926ejs $(@:_config=) spear spear
 
 spear600_config :	unconfig
-	@$(MKCONFIG) -n $@ -t $(@:_config=) spear6xx arm arm926ejs $(@:_config=) spear spear
+	@$(MKCONFIG) -n $@ -t $@ spear6xx arm arm926ejs $(@:_config=) spear spear
 
 suen3_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs km_arm keymile kirkwood
+	@$(MKCONFIG) $@ arm arm926ejs km_arm keymile kirkwood
 
 SX1_stdout_serial_config \
 SX1_config:		unconfig
@@ -2863,8 +2847,6 @@ SX1_config:		unconfig
 	@$(MKCONFIG) -n $@ SX1 arm arm925t sx1
 
 # TRAB default configuration:	8 MB Flash, 32 MB RAM
-xtract_trab = $(subst _bigram,,$(subst _bigflash,,$(subst _old,,$(subst _config,,$1))))
-
 trab_config \
 trab_bigram_config \
 trab_bigflash_config \
@@ -2885,24 +2867,24 @@ trab_old_config:	unconfig
 		  echo "#define CONFIG_RAM_16MB"   >>$(obj)include/config.h ; \
 		  echo "TEXT_BASE = 0x0CF40000" >$(obj)board/trab/config.tmp ; \
 		}
-	@$(MKCONFIG) -n $@ -a $(call xtract_trab,$@) arm arm920t trab NULL s3c24x0
+	@$(MKCONFIG) -n $@ -a trab arm arm920t trab NULL s3c24x0
 
 tx25_config	: unconfig
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
-	@$(MKCONFIG) $(@:_config=) arm arm926ejs tx25 karo mx25
+	@$(MKCONFIG) $@ arm arm926ejs tx25 karo mx25
 
 VCMA9_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t vcma9 mpl s3c24x0
+	@$(MKCONFIG) $@ arm arm920t vcma9 mpl s3c24x0
 
 #########################################################################
 # ARM supplied Versatile development boards
 #########################################################################
 
 cm4008_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t cm4008 NULL ks8695
+	@$(MKCONFIG) $@ arm arm920t cm4008 NULL ks8695
 
 cm41xx_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm920t cm41xx NULL ks8695
+	@$(MKCONFIG) $@ arm arm920t cm41xx NULL ks8695
 
 versatile_config	\
 versatileab_config	\
@@ -2910,116 +2892,116 @@ versatilepb_config :	unconfig
 	@board/armltd/versatile/split_by_variant.sh $@
 
 voiceblue_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm925t voiceblue
+	@$(MKCONFIG) $@ arm arm925t voiceblue
 
 #########################################################################
 ## S3C44B0 Systems
 #########################################################################
 
 B2_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm s3c44b0 B2 dave
+	@$(MKCONFIG) $@ arm s3c44b0 B2 dave
 
 #########################################################################
 ## ARM720T Systems
 #########################################################################
 
 armadillo_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm720t armadillo
+	@$(MKCONFIG) $@ arm arm720t armadillo
 
 ep7312_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm720t ep7312
+	@$(MKCONFIG) $@ arm arm720t ep7312
 
 impa7_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm720t impa7
+	@$(MKCONFIG) $@ arm arm720t impa7
 
 modnet50_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm720t modnet50
+	@$(MKCONFIG) $@ arm arm720t modnet50
 
 evb4510_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm720t evb4510 NULL s3c4510b
+	@$(MKCONFIG) $@ arm arm720t evb4510 NULL s3c4510b
 
 lpc2292sodimm_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm720t lpc2292sodimm NULL lpc2292
+	@$(MKCONFIG) $@ arm arm720t lpc2292sodimm NULL lpc2292
 
 SMN42_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm720t SMN42 siemens lpc2292
+	@$(MKCONFIG) $@ arm arm720t SMN42 siemens lpc2292
 
 #########################################################################
 ## ARM CORTEX Systems
 #########################################################################
 
 devkit8000_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 devkit8000 timll omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 devkit8000 timll omap3
 
 omap3_beagle_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 beagle ti omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 beagle ti omap3
 
 omap3_overo_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 overo NULL omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 overo NULL omap3
 
 omap3_evm_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 evm ti omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 evm ti omap3
 
 omap3_pandora_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 pandora NULL omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 pandora NULL omap3
 
 omap3_sdp3430_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 sdp3430 ti omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 sdp3430 ti omap3
 
 omap3_zoom1_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom1 logicpd omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 zoom1 logicpd omap3
 
 omap3_zoom2_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom2 logicpd omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 zoom2 logicpd omap3
 
 smdkc100_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 smdkc100 samsung s5pc1xx
+	@$(MKCONFIG) $@ arm arm_cortexa8 smdkc100 samsung s5pc1xx
 
 #########################################################################
 ## XScale Systems
 #########################################################################
 
 actux1_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm ixp actux1
+	@$(MKCONFIG) $@ arm ixp actux1
 
 actux2_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm ixp actux2
+	@$(MKCONFIG) $@ arm ixp actux2
 
 actux3_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm ixp actux3
+	@$(MKCONFIG) $@ arm ixp actux3
 
 actux4_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm ixp actux4
+	@$(MKCONFIG) $@ arm ixp actux4
 
 cerf250_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa cerf250
+	@$(MKCONFIG) $@ arm pxa cerf250
 
 cradle_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa cradle
+	@$(MKCONFIG) $@ arm pxa cradle
 
 csb226_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa csb226
+	@$(MKCONFIG) $@ arm pxa csb226
 
 delta_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa delta
+	@$(MKCONFIG) $@ arm pxa delta
 
 innokom_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa innokom
+	@$(MKCONFIG) $@ arm pxa innokom
 
 ixdp425_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm ixp ixdp425
+	@$(MKCONFIG) $@ arm ixp ixdp425
 
 ixdpg425_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm ixp ixdp425
+	@$(MKCONFIG) $@ arm ixp ixdp425
 
 lubbock_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa lubbock
+	@$(MKCONFIG) $@ arm pxa lubbock
 
 pleb2_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa pleb2
+	@$(MKCONFIG) $@ arm pxa pleb2
 
 logodl_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa logodl
+	@$(MKCONFIG) $@ arm pxa logodl
 
 pdnb3_config \
 scpu_config:	unconfig
@@ -3030,7 +3012,7 @@ scpu_config:	unconfig
 	@$(MKCONFIG) -n $@ -a pdnb3 arm ixp pdnb3 prodrive
 
 pxa255_idp_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa pxa255_idp
+	@$(MKCONFIG) $@ arm pxa pxa255_idp
 
 polaris_config \
 trizepsiv_config	:	unconfig
@@ -3041,19 +3023,19 @@ trizepsiv_config	:	unconfig
 	@$(MKCONFIG) -n $@ -a trizepsiv arm pxa trizepsiv
 
 wepep250_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa wepep250
+	@$(MKCONFIG) $@ arm pxa wepep250
 
 xaeniax_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa xaeniax
+	@$(MKCONFIG) $@ arm pxa xaeniax
 
 xm250_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa xm250
+	@$(MKCONFIG) $@ arm pxa xm250
 
 xsengine_config :	unconfig
-	@$(MKCONFIG) $(@:_config=) arm pxa xsengine
+	@$(MKCONFIG) $@ arm pxa xsengine
 
 zylonite_config :
-	@$(MKCONFIG) $(@:_config=) arm pxa zylonite
+	@$(MKCONFIG) $@ arm pxa zylonite
 
 #########################################################################
 ## ARM1136 Systems
@@ -3063,10 +3045,10 @@ apollon_config		: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_ONENAND_U_BOOT" > $(obj)include/config.h
 	@echo "CONFIG_ONENAND_U_BOOT = y" >> $(obj)include/config.mk
-	@$(MKCONFIG) $(@:_config=) arm arm1136 apollon NULL omap24xx
+	@$(MKCONFIG) $@ arm arm1136 apollon NULL omap24xx
 
 imx31_litekit_config	: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm1136 imx31_litekit logicpd mx31
+	@$(MKCONFIG) $@ arm arm1136 imx31_litekit logicpd mx31
 
 imx31_phycore_eet_config \
 imx31_phycore_config	: unconfig
@@ -3077,7 +3059,7 @@ imx31_phycore_config	: unconfig
 	@$(MKCONFIG) -n $@ -a imx31_phycore arm arm1136 imx31_phycore NULL mx31
 
 mx31ads_config		: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31
+	@$(MKCONFIG) $@ arm arm1136 mx31ads freescale mx31
 
 mx31pdk_config \
 mx31pdk_nand_config	: unconfig
@@ -3091,13 +3073,13 @@ mx31pdk_nand_config	: unconfig
 	@$(MKCONFIG) -n $@ -a mx31pdk arm arm1136 mx31pdk freescale mx31
 
 mx51evk_config	: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 mx51evk freescale mx51
+	@$(MKCONFIG) $@ arm arm_cortexa8 mx51evk freescale mx51
 
 omap2420h4_config	: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 ti omap24xx
+	@$(MKCONFIG) $@ arm arm1136 omap2420h4 ti omap24xx
 
 qong_config		: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm1136 qong davedenx mx31
+	@$(MKCONFIG) $@ arm arm1136 qong davedenx mx31
 
 #########################################################################
 ## ARM1176 Systems
@@ -3122,16 +3104,16 @@ smdk6400_config	:	unconfig
 ## AMD SC520 CDP
 #########################################################################
 eNET_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) i386 i386 eNET NULL sc520
+	@$(MKCONFIG) $@ i386 i386 eNET NULL sc520
 
 sc520_cdp_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) i386 i386 sc520_cdp NULL sc520
+	@$(MKCONFIG) $@ i386 i386 sc520_cdp NULL sc520
 
 sc520_spunk_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) i386 i386 sc520_spunk NULL sc520
+	@$(MKCONFIG) $@ i386 i386 sc520_spunk NULL sc520
 
 sc520_spunk_rel_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) i386 i386 sc520_spunk NULL sc520
+	@$(MKCONFIG) $@ i386 i386 sc520_spunk NULL sc520
 
 #========================================================================
 # MIPS
@@ -3154,7 +3136,7 @@ incaip_config: unconfig
 	@$(MKCONFIG) -n $@ -a incaip mips mips incaip
 
 tb0229_config: unconfig
-	@$(MKCONFIG) $(@:_config=) mips mips tb0229
+	@$(MKCONFIG) $@ mips mips tb0229
 
 vct_premium_config		\
 vct_premium_small_config	\
@@ -3213,7 +3195,7 @@ dbau1550_el_config	:	unconfig
 gth2_config		:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_GTH2 1" >$(obj)include/config.h
-	@$(MKCONFIG) -a gth2 mips mips gth2
+	@$(MKCONFIG) -a $@ mips mips gth2
 
 pb1000_config		:	unconfig
 	@mkdir -p $(obj)include
@@ -3230,7 +3212,7 @@ qemu_mips_config	: unconfig
 #########################################################################
 
 purple_config :		unconfig
-	@$(MKCONFIG) $(@:_config=) mips mips purple
+	@$(MKCONFIG) $@ mips mips purple
 
 #========================================================================
 # Nios
@@ -3241,33 +3223,32 @@ purple_config :		unconfig
 #########################################################################
 
 EP1C20_config : unconfig
-	@$(MKCONFIG)  EP1C20 nios2 nios2 ep1c20 altera
+	@$(MKCONFIG) $@ nios2 nios2 ep1c20 altera
 
 EP1S10_config : unconfig
-	@$(MKCONFIG)  EP1S10 nios2 nios2 ep1s10 altera
+	@$(MKCONFIG) $@ nios2 nios2 ep1s10 altera
 
 EP1S40_config : unconfig
-	@$(MKCONFIG)  EP1S40 nios2 nios2 ep1s40 altera
+	@$(MKCONFIG) $@ nios2 nios2 ep1s40 altera
 
 PK1C20_config : unconfig
-	@$(MKCONFIG)  PK1C20 nios2 nios2 pk1c20 psyent
+	@$(MKCONFIG) $@ nios2 nios2 pk1c20 psyent
 
 PCI5441_config : unconfig
-	@$(MKCONFIG)  PCI5441 nios2 nios2 pci5441 psyent
+	@$(MKCONFIG) $@ nios2 nios2 pci5441 psyent
 
 # nios2 generic boards
 NIOS2_GENERIC = nios2-generic
 
 $(NIOS2_GENERIC:%=%_config) : unconfig
-	@$(MKCONFIG) $(@:_config=) nios2 nios2 nios2-generic altera
+	@$(MKCONFIG) $@ nios2 nios2 nios2-generic altera
 
 #========================================================================
 ## Microblaze
 #========================================================================
 
 microblaze-generic_config:	unconfig
-	@mkdir -p $(obj)include
-	@$(MKCONFIG) -a $(@:_config=) microblaze microblaze microblaze-generic xilinx
+	@$(MKCONFIG) $@ microblaze microblaze microblaze-generic xilinx
 
 #========================================================================
 # Blackfin
@@ -3288,7 +3269,7 @@ BFIN_BOARDS += bf537-minotaur bf537-srv1 bf561-acvilon blackstamp ip04
 BFIN_BOARDS += ibf-dsp561
 
 $(BFIN_BOARDS:%=%_config)	: unconfig
-	@$(MKCONFIG) $(@:_config=) blackfin blackfin $(@:_config=)
+	@$(MKCONFIG) $@ blackfin blackfin $(@:_config=)
 
 bf527-ezkit-v2_config	: unconfig
 	@$(MKCONFIG) -t BF527_EZKIT_REV_2_1 \
@@ -3299,22 +3280,22 @@ bf527-ezkit-v2_config	: unconfig
 #========================================================================
 
 atngw100_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap atngw100 atmel at32ap700x
+	@$(MKCONFIG) $@ avr32 at32ap atngw100 atmel at32ap700x
 
 atstk1002_config	\
 atstk1003_config	\
 atstk1004_config	\
 atstk1006_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap atstk1000 atmel at32ap700x
+	@$(MKCONFIG) $@ avr32 at32ap atstk1000 atmel at32ap700x
 
 favr-32-ezkit_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap favr-32-ezkit earthlcd at32ap700x
+	@$(MKCONFIG) $@ avr32 at32ap favr-32-ezkit earthlcd at32ap700x
 
 hammerhead_config	:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap hammerhead miromico at32ap700x
+	@$(MKCONFIG) $@ avr32 at32ap hammerhead miromico at32ap700x
 
 mimc200_config		:	unconfig
-	@$(MKCONFIG) $(@:_config=) avr32 at32ap mimc200 mimc at32ap700x
+	@$(MKCONFIG) $@ avr32 at32ap mimc200 mimc at32ap700x
 
 #========================================================================
 # SH3 (SuperH)
@@ -3326,7 +3307,7 @@ mimc200_config		:	unconfig
 rsk7203_config: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_RSK7203 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh2 rsk7203 renesas
+	@$(MKCONFIG) -a $@ sh sh2 rsk7203 renesas
 
 #########################################################################
 ## sh3 (Renesas SuperH)
@@ -3335,12 +3316,12 @@ rsk7203_config: unconfig
 mpr2_config: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_MPR2 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh3 mpr2
+	@$(MKCONFIG) -a $@ sh sh3 mpr2
 
 ms7720se_config: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_MS7720SE 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh3 ms7720se
+	@$(MKCONFIG) -a $@ sh sh3 ms7720se
 
 #########################################################################
 ## sh4 (Renesas SuperH)
@@ -3349,34 +3330,33 @@ ms7720se_config: unconfig
 MigoR_config :       unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_MIGO_R 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 MigoR renesas
+	@$(MKCONFIG) -a $@ sh sh4 MigoR renesas
 
 ms7750se_config: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_MS7750SE 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 ms7750se
+	@$(MKCONFIG) -a $@ sh sh4 ms7750se
 
 ms7722se_config :	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_MS7722SE 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 ms7722se
+	@$(MKCONFIG) -a $@ sh sh4 ms7722se
 
 r2dplus_config  :   unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_R2DPLUS 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 r2dplus renesas
+	@$(MKCONFIG) -a $@ sh sh4 r2dplus renesas
 
 r7780mp_config: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_R7780MP 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 r7780mp renesas
+	@$(MKCONFIG) -a $@ sh sh4 r7780mp renesas
 
 sh7763rdp_config  :   unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_SH7763RDP 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 sh7763rdp renesas
+	@$(MKCONFIG) -a $@ sh sh4 sh7763rdp renesas
 
-xtract_sh7785lcr = $(subst _32bit,,$(subst _config,,$1))
 sh7785lcr_32bit_config \
 sh7785lcr_config  :   unconfig
 	@mkdir -p $(obj)include
@@ -3387,17 +3367,17 @@ sh7785lcr_config  :   unconfig
 		echo "TEXT_BASE = 0x8ff80000" > \
 			$(obj)board/renesas/sh7785lcr/config.tmp ; \
 	fi
-	@$(MKCONFIG) -n $@ -a $(call xtract_sh7785lcr,$@) sh sh4 sh7785lcr renesas
+	@$(MKCONFIG) -n $@ -a sh7785lcr sh sh4 sh7785lcr renesas
 
 ap325rxa_config  :   unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_AP325RXA 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 ap325rxa renesas
+	@$(MKCONFIG) -a $@ sh sh4 ap325rxa renesas
 
 espt_config  :   unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_ESPT 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $(@:_config=) sh sh4 espt
+	@$(MKCONFIG) -a $@ sh sh4 espt
 
 #========================================================================
 # SPARC
@@ -3409,20 +3389,20 @@ espt_config  :   unconfig
 
 # Gaisler GR-XC3S-1500 board
 gr_xc3s_1500_config : unconfig
-	@$(MKCONFIG) $(@:_config=) sparc leon3 gr_xc3s_1500 gaisler
+	@$(MKCONFIG) $@ sparc leon3 gr_xc3s_1500 gaisler
 
 # Gaisler GR-CPCI-AX2000 board, a General purpose FPGA-AX system
 gr_cpci_ax2000_config : unconfig
-	@$(MKCONFIG) $(@:_config=) sparc leon3 gr_cpci_ax2000 gaisler
+	@$(MKCONFIG) $@ sparc leon3 gr_cpci_ax2000 gaisler
 
 # Gaisler GRLIB template design (GPL SPARC/LEON3) for Altera NIOS
 # Development board Stratix II edition, FPGA Device EP2S60.
 gr_ep2s60_config: unconfig
-	@$(MKCONFIG) $(@:_config=) sparc leon3 gr_ep2s60 gaisler
+	@$(MKCONFIG) $@ sparc leon3 gr_ep2s60 gaisler
 
 # Gaisler LEON3 GRSIM simulator
 grsim_config : unconfig
-	@$(MKCONFIG) $(@:_config=) sparc leon3 grsim gaisler
+	@$(MKCONFIG) $@ sparc leon3 grsim gaisler
 
 #########################################################################
 ## LEON2
@@ -3430,7 +3410,7 @@ grsim_config : unconfig
 
 # Gaisler LEON2 GRSIM simulator
 grsim_leon2_config : unconfig
-	@$(MKCONFIG) $(@:_config=) sparc leon2 grsim_leon2 gaisler
+	@$(MKCONFIG) $@ sparc leon2 grsim_leon2 gaisler
 
 #########################################################################
 #########################################################################
diff --git a/mkconfig b/mkconfig
index d3109e4..a71d09e 100755
--- a/mkconfig
+++ b/mkconfig
@@ -16,13 +16,13 @@ while [ $# -gt 0 ] ; do
 	case "$1" in
 	--) shift ; break ;;
 	-a) shift ; APPEND=yes ;;
-	-n) shift ; BOARD_NAME="${1%%_config}" ; shift ;;
+	-n) shift ; BOARD_NAME="${1%_config}" ; shift ;;
 	-t) shift ; TARGETS="`echo $1 | sed 's:_: :g'` ${TARGETS}" ; shift ;;
 	*)  break ;;
 	esac
 done
 
-[ "${BOARD_NAME}" ] || BOARD_NAME="$1"
+[ "${BOARD_NAME}" ] || BOARD_NAME="${1%_config}"
 
 [ $# -lt 4 ] && exit 1
 [ $# -gt 6 ] && exit 1
@@ -102,7 +102,7 @@ done
 cat << EOF >> config.h
 #define CONFIG_BOARDDIR board/$BOARDDIR
 #include <config_defaults.h>
-#include <configs/$1.h>
+#include <configs/${BOARDNAME}.h>
 #include <asm/config.h>
 EOF
 
-- 
cgit v1.1


From 8c994630b90fe5e6ced15105eee4549e3338abcc Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Thu, 27 May 2010 23:18:35 +0200
Subject: Makefile: simplify handling of common board configurations

Many boards don't need any special handling in the Makefile. Try and
provide as generic make rules for these as possible.  There are still
many areas where this does not work out really well, but the changes
show the direction we should take, and point out which boards or
architectures need further cleanup.

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 Makefile | 1446 ++++++++++++++++++++++++++------------------------------------
 1 file changed, 612 insertions(+), 834 deletions(-)

diff --git a/Makefile b/Makefile
index 25d531e..42d807b 100644
--- a/Makefile
+++ b/Makefile
@@ -478,6 +478,12 @@ unconfig:
 %: %_config
 	$(MAKE)
 
+#
+# Functions to generate common board directory names
+#
+lcname	= $(shell echo $(1) | sed -e 's/\(.*\)_config/\L\1/')
+ucname	= $(shell echo $(1) | sed -e 's/\(.*\)_config/\U\1/')
+
 #========================================================================
 # PowerPC
 #========================================================================
@@ -496,21 +502,37 @@ PATI_config:		unconfig
 ## MPC5xxx Systems
 #########################################################################
 
-aev_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
-
-BC3450_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx bc3450
-
-canmb_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx canmb
-
-cm5200_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx cm5200
+# generic boards
+################
+BC3450_config	\
+canmb_config	\
+cm5200_config	\
+hmi1001_config	\
+jupiter_config	\
+inka4x0_config	\
+ipek01_config	\
+motionpro_config\
+mucmc52_config	\
+munices_config	\
+o2dnt_config	\
+uc101_config	\
+v38b_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc5xxx $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+cpci5200_config	\
+mecp5200_config	\
+pf5200_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc5xxx $(call lcname,$@) esd
 
-cpci5200_config:  unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx cpci5200 esd
+aev_config	\
+smmaco4_config	\
+spieval_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
 
+# special boards
+################
 digsy_mtc_config \
 digsy_mtc_LOWBOOT_config	\
 digsy_mtc_RAMBOOT_config:	unconfig
@@ -529,9 +551,6 @@ galaxy5200_config:	unconfig
 	@echo "#define CONFIG_$(@:_config=) 1" >$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a galaxy5200 powerpc mpc5xxx galaxy5200
 
-hmi1001_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx hmi1001
-
 Lite5200_config				\
 Lite5200_LOWBOOT_config			\
 Lite5200_LOWBOOT08_config		\
@@ -554,15 +573,6 @@ icecube_5200_DDR_LOWBOOT08_config:	unconfig
 		echo "#define CONFIG_MPC5200_DDR" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a IceCube powerpc mpc5xxx icecube
 
-jupiter_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx jupiter
-
-inka4x0_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx inka4x0
-
-ipek01_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx ipek01
-
 lite5200b_config	\
 lite5200b_PM_config	\
 lite5200b_LOWBOOT_config:	unconfig
@@ -608,18 +618,6 @@ prs200_highboot_DDR_config:	unconfig
 		echo "#define CONFIG_PRS200" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a mcc200 powerpc mpc5xxx mcc200
 
-mecp5200_config:  unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx mecp5200 esd
-
-motionpro_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx motionpro
-
-mucmc52_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx mucmc52
-
-munices_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx munices
-
 MVBC_P_config: unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/mvbc_p
@@ -633,9 +631,6 @@ MVSMR_config: unconfig
 	@mkdir -p $(obj)board/matrix_vision/mvsmr
 	@$(MKCONFIG) $@ powerpc mpc5xxx mvsmr matrix_vision
 
-o2dnt_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx o2dnt
-
 pcm030_config \
 pcm030_LOWBOOT_config:	unconfig
 	@mkdir -p $(obj)include $(obj)board/phytec/pcm030
@@ -644,9 +639,6 @@ pcm030_LOWBOOT_config:	unconfig
 		echo "TEXT_BASE = 0xFF000000" >$(obj)board/phytec/pcm030/config.tmp
 	@$(MKCONFIG) -n $@ -a pcm030 powerpc mpc5xxx pcm030 phytec
 
-pf5200_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx pf5200 esd
-
 PM520_config \
 PM520_DDR_config \
 PM520_ROMBOOT_config \
@@ -658,12 +650,6 @@ PM520_ROMBOOT_DDR_config:	unconfig
 		echo "#define CONFIG_BOOT_ROM" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a PM520 powerpc mpc5xxx pm520
 
-smmaco4_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
-
-spieval_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
-
 TB5200_B_config \
 TB5200_config:	unconfig
 	@mkdir -p $(obj)include
@@ -727,22 +713,25 @@ TQM5200_STK100_config:	unconfig
 		echo "TEXT_BASE = 0xFFF00000" >$(obj)board/tqm5200/config.tmp
 	@$(MKCONFIG) -n $@ -a TQM5200 powerpc mpc5xxx tqm5200 tqc
 
-uc101_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx uc101
-
-v38b_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx v38b
-
 #########################################################################
 ## MPC512x Systems
 #########################################################################
 
+# generic boards
+################
+pdm360ng_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc512x $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
 aria_config:	unconfig
 	@$(MKCONFIG) $@ powerpc mpc512x aria davedenx
 
 mecp5123_config:	unconfig
 	@$(MKCONFIG) $@ powerpc mpc512x mecp5123 esd
 
+# special boards
+################
 mpc5121ads_config \
 mpc5121ads_rev2_config	\
 	: unconfig
@@ -752,13 +741,84 @@ mpc5121ads_rev2_config	\
 	fi
 	@$(MKCONFIG) -n $@ -a mpc5121ads powerpc mpc512x mpc5121ads freescale
 
-pdm360ng_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc512x pdm360ng
-
 #########################################################################
 ## MPC8xx Systems
 #########################################################################
 
+# generic boards
+################
+
+c2mon_config		\
+EP88x_config		\
+ESTEEM192E_config	\
+ETX094_config		\
+FLAGADM_config		\
+GENIETV_config		\
+GTH_config		\
+hermes_config		\
+IP860_config		\
+LANTEC_config		\
+lwmon_config		\
+NX823_config		\
+quantum_config		\
+R360MPI_config		\
+RBC823_config		\
+rmu_config		\
+spc1920_config		\
+svm_sc8xx_config	\
+uc100_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx $(call lcname,$@)
+
+RPXClassic_config	\
+RPXlite_config		\
+RRvision_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx $(@:_config=)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
+MHPC_config:		unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx mhpc eltec
+
+TOP860_config:		unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx top860 emk
+
+kmsupx4_config	\
+mgsuvd_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx km8xx keymile
+
+KUP4K_config	\
+KUP4X_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx $(call lcname,$@) kup
+
+ELPT860_config:		unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx elpt860 LEOX
+
+stxxtc_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx stxxtc stx
+
+HMI10_config	\
+SM850_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx tqm8xx tqc
+
+CCM_config	\
+IAD210_config	\
+pcu_e_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx $(@:_config=) siemens
+
+QS823_config	\
+QS850_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx qs850 snmc
+
+QS860T_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx qs860t snmc
+
+AMX860_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8xx amx860 westel
+
+# special boards
+################
+
 Adder87x_config \
 AdderII_config	\
 AdderUSB_config	\
@@ -769,6 +829,9 @@ Adder_config	\
 		@echo "#define CONFIG_MPC852T" > $(obj)include/config.h)
 	@$(MKCONFIG) -n $@ -a Adder powerpc mpc8xx adder
 
+cogent_mpc8xx_config:	unconfig
+	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx cogent
+
 ADS860_config	  \
 FADS823_config	  \
 FADS850SAR_config \
@@ -777,33 +840,6 @@ MPC885ADS_config  \
 FADS860T_config:	unconfig
 	@$(MKCONFIG) -n $@ $@ powerpc mpc8xx fads
 
-AMX860_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx amx860 westel
-
-c2mon_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx c2mon
-
-CCM_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx CCM siemens
-
-cogent_mpc8xx_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx cogent
-
-ELPT860_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx elpt860 LEOX
-
-EP88x_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx ep88x
-
-ESTEEM192E_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx esteem192e
-
-ETX094_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx etx094
-
-FLAGADM_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx flagadm
-
 GEN860T_SC_config	\
 GEN860T_config: unconfig
 	@mkdir -p $(obj)include
@@ -811,21 +847,6 @@ GEN860T_config: unconfig
 		echo "#define CONFIG_SC" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a GEN860T powerpc mpc8xx gen860t
 
-GENIETV_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx genietv
-
-GTH_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx gth
-
-hermes_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx hermes
-
-HMI10_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx tqm8xx tqc
-
-IAD210_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx IAD210 siemens
-
 ICU862_100MHz_config	\
 ICU862_config: unconfig
 	@mkdir -p $(obj)include
@@ -833,9 +854,6 @@ ICU862_config: unconfig
 		echo "#define CONFIG_100MHz" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a ICU862 powerpc mpc8xx icu862
 
-IP860_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx ip860
-
 IVML24_256_config \
 IVML24_128_config \
 IVML24_config:	unconfig
@@ -860,31 +878,10 @@ IVMS8_config:	unconfig
 		echo "#define CONFIG_IVMS8_64M"	>>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a IVMS8 powerpc mpc8xx ivm
 
-kmsupx4_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx km8xx keymile
-
-KUP4K_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx kup4k kup
-
-KUP4X_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx kup4x kup
-
-LANTEC_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx lantec
-
-lwmon_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx lwmon
-
 MBX_config	\
 MBX860T_config:	unconfig
 	@$(MKCONFIG) -n $@ $@ powerpc mpc8xx mbx8xx
 
-mgsuvd_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx km8xx keymile
-
-MHPC_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx mhpc eltec
-
 NETVIA_V2_config \
 NETVIA_config:		unconfig
 	@mkdir -p $(obj)include
@@ -951,36 +948,6 @@ CP850_config:	unconfig
 		}
 	@$(MKCONFIG) -n $@ -a NC650 powerpc mpc8xx nc650
 
-NX823_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx nx823
-
-pcu_e_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx pcu_e siemens
-
-QS850_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx qs850 snmc
-
-QS823_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx qs850 snmc
-
-QS860T_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx qs860t snmc
-
-quantum_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx quantum
-
-R360MPI_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx r360mpi
-
-RBC823_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx rbc823
-
-RPXClassic_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx RPXClassic
-
-RPXlite_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx RPXlite
-
 RPXlite_DW_64_config		\
 RPXlite_DW_LCD_config		\
 RPXlite_DW_64_LCD_config	\
@@ -1000,40 +967,18 @@ RPXlite_DW_config:	unconfig
 		echo "#define  CONFIG_ENV_IS_IN_NVRAM"	>>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a RPXlite_DW powerpc mpc8xx RPXlite_dw
 
-rmu_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx rmu
-
-RRvision_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx RRvision
-
 RRvision_LCD_config:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_LCD" >$(obj)include/config.h
 	@echo "#define CONFIG_SHARP_LQ104V7DS01" >>$(obj)include/config.h
 	@$(MKCONFIG) -a RRvision powerpc mpc8xx RRvision
 
-SM850_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx tqm8xx tqc
-
-spc1920_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx spc1920
-
 SPD823TS_config:	unconfig
 	@$(MKCONFIG) $@ powerpc mpc8xx spd8xx
 
-stxxtc_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx stxxtc stx
-
-svm_sc8xx_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx svm_sc8xx
-
 SXNI855T_config:	unconfig
 	@$(MKCONFIG) $@ powerpc mpc8xx sixnet
 
-# EMK MPC8xx based modules
-TOP860_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx top860 emk
-
 # Play some tricks for configuration selection
 # Only 855 and 860 boards may come with FEC
 # and only 823 boards may have LCD support
@@ -1070,9 +1015,6 @@ TTTech_config:	unconfig
 	@echo "#define CONFIG_SHARP_LQ104V7DS01" >>$(obj)include/config.h
 	@$(MKCONFIG) -a TQM823L powerpc mpc8xx tqm8xx tqc
 
-uc100_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx uc100
-
 v37_config:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_LCD" >$(obj)include/config.h
@@ -1089,37 +1031,110 @@ wtk_config:	unconfig
 ## PPC4xx Systems
 #########################################################################
 
-acadia_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx acadia amcc
+# generic boards
+################
+
+csb272_config	\
+csb472_config	\
+ERIC_config	\
+G2000_config	\
+JSE_config	\
+korat_config	\
+lwmon5_config	\
+ML2_config	\
+pcs440ep_config	\
+quad100hd_config\
+sbc405_config	\
+sc3_config	\
+zeus_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
+acadia_config	\
+bamboo_config	\
+bubinga_config	\
+ebony_config	\
+katmai_config	\
+luan_config	\
+makalu_config	\
+ocotea_config	\
+redwood_config	\
+taihu_config	\
+taishan_config	\
+yucca_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) amcc
 
-acadia_nand_config:	unconfig
-	@mkdir -p $(obj)include $(obj)board/amcc/acadia
-	@mkdir -p $(obj)nand_spl/board/amcc/acadia
-	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
-	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/acadia/config.tmp
-	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
-	@$(MKCONFIG) -n $@ -a acadia powerpc ppc4xx acadia amcc
+AP1000_config:unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) amirix
+
+ADCIOP_config	\
+APC405_config	\
+AR405_config	\
+ASH405_config	\
+CANBT_config	\
+CMS700_config	\
+CPCI2DP_config	\
+CPCIISER4_config\
+DASA_SIM_config	\
+DP405_config	\
+DU405_config	\
+DU440_config	\
+HH405_config	\
+HUB405_config	\
+PCI405_config	\
+PLU405_config	\
+PMC405_config	\
+PMC405DE_config	\
+PMC440_config	\
+VOH405_config	\
+VOM405_config	\
+WUH405_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) esd
+
+CRAYL1_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx L1 cray
 
-ADCIOP_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx adciop esd
+dlvision_config		\
+gdppc440etx_config	\
+neo_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) gdsys
 
-alpr_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx alpr prodrive
+icon_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) mosaixtech
 
-AP1000_config:unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx ap1000 amirix
+MIP405_config	\
+PIP405_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) mpl
 
-APC405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx apc405 esd
+hcu4_config	\
+hcu5_config	\
+mcu25_config:  unconfig
+	@mkdir -p $(obj)board/netstal/common
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) netstal
+
+alpr_config	\
+p3p440_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) prodrive
 
-AR405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx ar405 esd
+KAREF_config	\
+METROBOX_config: unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) sandburst
 
-ASH405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx ash405 esd
+XPEDITE1000_config:	unconfig
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) xes
 
-bamboo_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx bamboo amcc
+# special boards
+################
+
+acadia_nand_config:	unconfig
+	@mkdir -p $(obj)include $(obj)board/amcc/acadia
+	@mkdir -p $(obj)nand_spl/board/amcc/acadia
+	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
+	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/acadia/config.tmp
+	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+	@$(MKCONFIG) -n $@ -a acadia powerpc ppc4xx acadia amcc
 
 bamboo_nand_config:	unconfig
 	@mkdir -p $(obj)include $(obj)board/amcc/bamboo
@@ -1129,12 +1144,6 @@ bamboo_nand_config:	unconfig
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 	@$(MKCONFIG) -n $@ -a bamboo powerpc ppc4xx bamboo amcc
 
-bubinga_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx bubinga amcc
-
-CANBT_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx canbt esd
-
 # Arches, Canyonlands & Glacier use different U-Boot images
 arches_config \
 canyonlands_config \
@@ -1167,12 +1176,6 @@ CATcenter_33_config:	unconfig
 		echo "#define CONFIG_PPCHAMELEON_CLK_33" >> $(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a CATcenter powerpc ppc4xx PPChameleonEVB dave
 
-CMS700_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx cms700 esd
-
-CPCI2DP_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx cpci2dp esd
-
 CPCI405_config		\
 CPCI4052_config		\
 CPCI405DT_config	\
@@ -1180,39 +1183,6 @@ CPCI405AB_config:	unconfig
 	@mkdir -p $(obj)board/esd/cpci405
 	@$(MKCONFIG) -n $@ $@ powerpc ppc4xx cpci405 esd
 
-CPCIISER4_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx cpciiser4 esd
-
-CRAYL1_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx L1 cray
-
-csb272_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx csb272
-
-csb472_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx csb472
-
-DASA_SIM_config: unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx dasa_sim esd
-
-dlvision_config: unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx dlvision gdsys
-
-DP405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx dp405 esd
-
-DU405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx du405 esd
-
-DU440_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx du440 esd
-
-ebony_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx ebony amcc
-
-ERIC_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx eric
-
 fx12mm_flash_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc405-generic
 	@mkdir -p $(obj)include $(obj)board/avnet/fx12mm
@@ -1231,29 +1201,6 @@ fx12mm_config: unconfig
 		>> $(obj)board/avnet/fx12mm/config.tmp
 	@$(MKCONFIG) fx12mm powerpc ppc4xx fx12mm avnet
 
-G2000_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx g2000
-
-gdppc440etx_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx gdppc440etx gdsys
-
-hcu4_config:	unconfig
-	@mkdir -p $(obj)board/netstal/common
-	@$(MKCONFIG) $@ powerpc ppc4xx hcu4 netstal
-
-hcu5_config:	unconfig
-	@mkdir -p $(obj)board/netstal/common
-	@$(MKCONFIG) $@ powerpc ppc4xx hcu5 netstal
-
-HH405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx hh405 esd
-
-HUB405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx hub405 esd
-
-icon_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx icon mosaixtech
-
 # Compact-Center(codename intip) & DevCon-Center use different U-Boot images
 intip_config \
 devconcenter_config:	unconfig
@@ -1262,15 +1209,6 @@ devconcenter_config:	unconfig
 		tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a intip powerpc ppc4xx intip gdsys
 
-JSE_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx jse
-
-KAREF_config: unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx karef sandburst
-
-katmai_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx katmai amcc
-
 # Kilauea & Haleakala images are identical (recognized via PVR)
 kilauea_config \
 haleakala_config: unconfig
@@ -1285,37 +1223,12 @@ haleakala_nand_config: unconfig
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 	@$(MKCONFIG) -n $@ -a kilauea powerpc ppc4xx kilauea amcc
 
-korat_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx korat
-
-luan_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx luan amcc
-
-lwmon5_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx lwmon5
-
-makalu_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx makalu amcc
-
-mcu25_config:  unconfig
-	@mkdir -p $(obj)board/netstal/common
-	@$(MKCONFIG) $@ powerpc ppc4xx mcu25 netstal
-
-METROBOX_config: unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx metrobox sandburst
-
-MIP405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx mip405 mpl
-
 MIP405T_config:	unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_MIP405T" >$(obj)include/config.h
 	@$(XECHO) "Enable subset config for MIP405T"
 	@$(MKCONFIG) -a MIP405 powerpc ppc4xx mip405 mpl
 
-ML2_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx ml2
-
 ml507_flash_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
 	@mkdir -p $(obj)include $(obj)board/xilinx/ml507
@@ -1334,40 +1247,10 @@ ml507_config: unconfig
 		>> $(obj)board/xilinx/ml507/config.tmp
 	@$(MKCONFIG) $@ powerpc ppc4xx ml507 xilinx
 
-neo_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx neo gdsys
-
-ocotea_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx ocotea amcc
-
 OCRTC_config		\
 ORSG_config:	unconfig
 	@$(MKCONFIG) -n $@ $@ powerpc ppc4xx ocrtc esd
 
-p3p440_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx p3p440 prodrive
-
-PCI405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx pci405 esd
-
-pcs440ep_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx pcs440ep
-
-PIP405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx pip405 mpl
-
-PLU405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx plu405 esd
-
-PMC405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx pmc405 esd
-
-PMC405DE_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx pmc405de esd
-
-PMC440_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx pmc440 esd
-
 PPChameleonEVB_config		\
 PPChameleonEVB_BA_25_config	\
 PPChameleonEVB_ME_25_config	\
@@ -1388,18 +1271,6 @@ PPChameleonEVB_HI_33_config:	unconfig
 		echo "#define CONFIG_PPCHAMELEON_CLK_33" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a PPChameleonEVB powerpc ppc4xx PPChameleonEVB dave
 
-quad100hd_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx quad100hd
-
-redwood_config: unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx redwood amcc
-
-sbc405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx sbc405
-
-sc3_config:unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx sc3
-
 sequoia_config \
 rainier_config: unconfig
 	@mkdir -p $(obj)include
@@ -1429,12 +1300,6 @@ rainier_ramboot_config: unconfig
 		$(obj)board/amcc/sequoia/config.tmp
 	@$(MKCONFIG) -n $@ -a sequoia powerpc ppc4xx sequoia amcc
 
-taihu_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx taihu amcc
-
-taishan_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx taishan amcc
-
 v5fx30teval_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
 	@mkdir -p $(obj)include $(obj)board/avnet/v5fx30teval
@@ -1453,12 +1318,6 @@ v5fx30teval_flash_config: unconfig
 		>> $(obj)board/avnet/v5fx30teval/config.tmp
 	@$(MKCONFIG) v5fx30teval powerpc ppc4xx v5fx30teval avnet
 
-VOH405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx voh405 esd
-
-VOM405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx vom405 esd
-
 W7OLMC_config	\
 W7OLMG_config: unconfig
 	@$(MKCONFIG) $@ powerpc ppc4xx w7o
@@ -1468,9 +1327,6 @@ walnut_config \
 sycamore_config: unconfig
 	@$(MKCONFIG) -n $@ walnut powerpc ppc4xx walnut amcc
 
-WUH405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx wuh405 esd
-
 xilinx-ppc405-generic_flash_config: unconfig
 	@mkdir -p $(obj)include $(obj)board/xilinx/ppc405-generic
 	@echo "LDSCRIPT:=$(SRCTREE)/board/xilinx/ppc405-generic/u-boot-rom.lds"\
@@ -1503,9 +1359,6 @@ xilinx-ppc440-generic_config: unconfig
 		>> $(obj)board/xilinx/ppc440-generic/config.tmp
 	@$(MKCONFIG) xilinx-ppc440-generic powerpc ppc4xx ppc440-generic xilinx
 
-XPEDITE1000_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx xpedite1000 xes
-
 yosemite_config \
 yellowstone_config: unconfig
 	@mkdir -p $(obj)include
@@ -1513,35 +1366,50 @@ yellowstone_config: unconfig
 		tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a yosemite powerpc ppc4xx yosemite amcc
 
-yucca_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx yucca amcc
-
-zeus_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx zeus
-
 #########################################################################
 ## MPC8220 Systems
 #########################################################################
 
+# generic boards
+################
+sorcery_config:		unconfig
+	@$(MKCONFIG) $@ powerpc mpc8220 $(call lcname,$@)
+
 Alaska8220_config	\
 Yukon8220_config:	unconfig
 	@$(MKCONFIG) $@ powerpc mpc8220 alaska
 
-sorcery_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8220 sorcery
-
 #########################################################################
 ## MPC824x Systems
 #########################################################################
 
-A3000_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x a3000
-
-barco_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x barco
-
-BMW_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x bmw
+# generic boards
+################
+A3000_config	\
+barco_config	\
+BMW_config	\
+CU824_config	\
+HIDDEN_DRAGON_config \
+MOUSSE_config	\
+MUSENKI_config	\
+MVBLUE_config	\
+OXC_config	\
+PN62_config	\
+sbc8240_config	\
+utx8245_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc824x $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
+debris_config	\
+kvme080_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc824x $(call lcname,$@) etin
+
+# special boards
+################
+eXalion_config: unconfig
+	@$(MKCONFIG) $(@:_config=) powerpc mpc824x eXalion
 
 CPC45_config	\
 CPC45_ROMBOOT_config:	unconfig
@@ -1554,21 +1422,6 @@ CPC45_ROMBOOT_config:	unconfig
 	echo "export CONFIG_BOOT_ROM" >> $(obj)include/config.mk;
 	@$(MKCONFIG) -n $@ CPC45 powerpc mpc824x cpc45
 
-CU824_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x cu824
-
-debris_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x debris etin
-
-eXalion_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x eXalion
-
-HIDDEN_DRAGON_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x hidden_dragon
-
-kvme080_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x kvme080 etin
-
 # HDLAN is broken ATM. Should be fixed as soon as hardware is available and as
 # time permits.
 #linkstation_HDLAN_config \
@@ -1581,42 +1434,53 @@ linkstation_HGLAN_config: unconfig
 	esac
 	@$(MKCONFIG) -n $@ -a linkstation powerpc mpc824x linkstation
 
-MOUSSE_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x mousse
-
-MUSENKI_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x musenki
-
-MVBLUE_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x mvblue
-
-OXC_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x oxc
-
-PN62_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x pn62
-
 Sandpoint8240_config: unconfig
 	@$(MKCONFIG) $@ powerpc mpc824x sandpoint
 
 Sandpoint8245_config: unconfig
 	@$(MKCONFIG) $@ powerpc mpc824x sandpoint
 
-sbc8240_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x sbc8240
-
-utx8245_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x utx8245
-
 #########################################################################
 ## MPC8260 Systems
 #########################################################################
 
-atc_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 atc
+# generic boards
+################
+atc_config		\
+ep8260_config		\
+ep82xxm_config		\
+gw8260_config		\
+hymod_config		\
+IDS8247_config		\
+IPHASE4539_config	\
+ppmc8260_config		\
+RPXsuper_config		\
+rsdproto_config		\
+sacsng_config		\
+sbc8260_config		\
+ZPC1900_config:		unconfig
+	@$(MKCONFIG) $@ powerpc mpc8260 $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
+MPC8266ADS_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8260 $(call lcname,$@) freescale
+
+mgcoge_config	:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc8260 $(call lcname,$@) keymile
+
+SCM_config:		unconfig
+	@$(MKCONFIG) $@ powerpc mpc8260 $(call ucname,$@) siemens
+
+TQM8272_config: unconfig
+	@$(MKCONFIG) TQM8272 powerpc mpc8260 $(call lcname,$@) tqc
+
+# special boards
+################
 
 cogent_mpc8260_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 cogent
+	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 cogent
 
 CPU86_config	\
 CPU86_ROMBOOT_config: unconfig
@@ -1644,24 +1508,6 @@ ep8248_config	\
 ep8248E_config	:	unconfig
 	@$(MKCONFIG) -n $@ ep8248 powerpc mpc8260 ep8248
 
-ep8260_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 ep8260
-
-ep82xxm_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 ep82xxm
-
-gw8260_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 gw8260
-
-hymod_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 hymod
-
-IDS8247_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 ids8247
-
-IPHASE4539_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 iphase4539
-
 ISPAN_config		\
 ISPAN_REVB_config:	unconfig
 	@mkdir -p $(obj)include
@@ -1670,9 +1516,6 @@ ISPAN_REVB_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a ISPAN powerpc mpc8260 ispan
 
-mgcoge_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 mgcoge keymile
-
 MPC8260ADS_config	\
 MPC8260ADS_lowboot_config	\
 MPC8260ADS_33MHz_config	\
@@ -1703,9 +1546,6 @@ PQ2FADS-ZU_66MHz_lowboot_config	\
 		echo "TEXT_BASE = 0xFF800000" >$(obj)board/freescale/mpc8260ads/config.tmp
 	@$(MKCONFIG) -n $@ -a MPC8260ADS powerpc mpc8260 mpc8260ads freescale
 
-MPC8266ADS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 mpc8266ads freescale
-
 muas3001_dev_config \
 muas3001_config	:	unconfig
 	@mkdir -p $(obj)include
@@ -1763,30 +1603,12 @@ PM828_ROMBOOT_PCI_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a PM828 powerpc mpc8260 pm828
 
-ppmc8260_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 ppmc8260
-
 Rattler8248_config	\
-Rattler_config:		unconfig
-	@mkdir -p $(obj)include
-	$(if $(findstring 8248,$@), \
-		@echo "#define CONFIG_MPC8248" > $(obj)include/config.h)
-	@$(MKCONFIG) -n $@ -a Rattler powerpc mpc8260 rattler
-
-RPXsuper_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 rpxsuper
-
-rsdproto_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 rsdproto
-
-sacsng_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 sacsng
-
-sbc8260_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 sbc8260
-
-SCM_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 SCM siemens
+Rattler_config:		unconfig
+	@mkdir -p $(obj)include
+	$(if $(findstring 8248,$@), \
+		@echo "#define CONFIG_MPC8248" > $(obj)include/config.h)
+	@$(MKCONFIG) -n $@ -a Rattler powerpc mpc8260 rattler
 
 TQM8255_AA_config \
 TQM8260_AA_config \
@@ -1829,29 +1651,49 @@ TQM8265_AA_config:  unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a TQM8260 powerpc mpc8260 tqm8260 tqc
 
-TQM8272_config: unconfig
-	@$(MKCONFIG) TQM8272 powerpc mpc8260 tqm8272 tqc
-
 VoVPN-GW_66MHz_config	\
 VoVPN-GW_100MHz_config:		unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_CLKIN_$(word 2,$(subst _, ,$@))" > $(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a VoVPN-GW powerpc mpc8260 vovpn-gw funkwerk
 
-ZPC1900_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 zpc1900
-
 #########################################################################
 ## Coldfire
 #########################################################################
 
+# generic boards
+################
+
+idmr_config:		unconfig
+	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
+TASREG_config :		unconfig
+	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@) esd
+
+M5208EVBE_config	\
+M5249EVB_config		\
+M5253DEMO_config	\
+M5253EVBE_config	\
+M5271EVB_config		\
+M5272C3_config		\
+M5275EVB_config		\
+M5282EVB_config		\
+M53017EVB_config:	unconfig
+	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@) freescale
+
+EP2500_config	:	unconfig
+	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@) Mercury
+
+# special boards
+################
+
 astro_mcf5373l_config \
 astro_mcf5373l_RAM_config :	unconfig
 	@$(MKCONFIG) -n $@ -t $@ astro_mcf5373l m68k mcf532x mcf5373l astro
 
-M5208EVBE_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5208evbe freescale
-
 M52277EVB_config \
 M52277EVB_spansion_config \
 M52277EVB_stmicro_config :	unconfig
@@ -1891,15 +1733,6 @@ M5235EVB_Flash32_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a M5235EVB m68k mcf523x m5235evb freescale
 
-M5249EVB_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5249evb freescale
-
-M5253DEMO_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5253demo freescale
-
-M5253EVBE_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5253evbe freescale
-
 cobra5272_config :		unconfig
 	@$(MKCONFIG) $@ m68k mcf52x2 cobra5272
 
@@ -1915,27 +1748,6 @@ EB+MCF-EV123_internal_config :	unconfig
 	@echo "TEXT_BASE = 0xF0000000"|tee $(obj)board/BuS/EB+MCF-EV123/textbase.mk
 	@$(MKCONFIG) -n $@ EB+MCF-EV123 m68k mcf52x2 EB+MCF-EV123 BuS
 
-EP2500_config:			unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 ep2500 Mercury
-
-idmr_config :			unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 idmr
-
-M5271EVB_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5271evb freescale
-
-M5272C3_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5272c3 freescale
-
-M5275EVB_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5275evb freescale
-
-M5282EVB_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 m5282evb freescale
-
-M53017EVB_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf532x m53017evb freescale
-
 M5329AFEE_config \
 M5329BFEE_config :	unconfig
 	@case "$@" in \
@@ -2080,15 +1892,32 @@ M5485HFE_config :	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a M5485EVB m68k mcf547x_8x m548xevb freescale
 
-TASREG_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 tasreg esd
-
 #########################################################################
 ## MPC83xx Systems
 #########################################################################
 
+# generic boards
+################
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
+MPC8323ERDB_config	\
+MPC8349EMDS_config	\
+MPC837XERDB_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) freescale
+
 kmeter1_config: unconfig
-	@$(MKCONFIG) kmeter1 powerpc mpc83xx kmeter1 keymile
+	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) keymile
+
+MVBLM7_config: unconfig
+	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) matrix_vision
+
+TQM834x_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) tqc
+
+# special boards
+################
 
 MPC8313ERDB_33_config \
 MPC8313ERDB_66_config \
@@ -2115,9 +1944,6 @@ MPC8315ERDB_NAND_config \
 MPC8315ERDB_config: unconfig
 	@$(MKCONFIG) -n $@ -t $@ MPC8315ERDB powerpc mpc83xx mpc8315erdb freescale
 
-MPC8323ERDB_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx mpc8323erdb freescale
-
 MPC832XEMDS_config \
 MPC832XEMDS_HOST_33_config \
 MPC832XEMDS_HOST_66_config \
@@ -2145,9 +1971,6 @@ MPC832XEMDS_ATM_config:	unconfig
 	fi ;
 	@$(MKCONFIG) -n $@ -a MPC832XEMDS powerpc mpc83xx mpc832xemds freescale
 
-MPC8349EMDS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx mpc8349emds freescale
-
 MPC8349ITX_config \
 MPC8349ITX_LOWBOOT_config \
 MPC8349ITXGP_config:	unconfig
@@ -2206,12 +2029,6 @@ MPC837XEMDS_HOST_config:	unconfig
 	fi ;
 	@$(MKCONFIG) -n $@ -a MPC837XEMDS powerpc mpc83xx mpc837xemds freescale
 
-MPC837XERDB_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx mpc837xerdb freescale
-
-MVBLM7_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx mvblm7 matrix_vision
-
 sbc8349_config \
 sbc8349_PCI_33_config \
 sbc8349_PCI_66_config: unconfig
@@ -2230,30 +2047,41 @@ SIMPC8313_SP_config: unconfig
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 	@$(MKCONFIG) -n $@ -a SIMPC8313 powerpc mpc83xx simpc8313 sheldon
 
-TQM834x_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx tqm834x tqc
-
 caddy2_config \
 vme8349_config:		unconfig
 	@$(MKCONFIG) -n $@ -t $@ vme8349 powerpc mpc83xx vme8349 esd
 
-edb9301_config \
-edb9302_config \
-edb9302a_config \
-edb9307_config \
-edb9307a_config \
-edb9312_config \
-edb9315_config \
-edb9315a_config: unconfig
-	@$(MKCONFIG) -n $@ -t $@ edb93xx arm arm920t edb93xx NULL ep93xx
-
 #########################################################################
 ## MPC85xx Systems
 #########################################################################
 
-ATUM8548_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx atum8548
+# generic boards
+################
+
+ATUM8548_config		\
+PM854_config		\
+PM856_config		\
+socrates_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
+MPC8540ADS_config	\
+MPC8560ADS_config	\
+MPC8544DS_config	\
+MPC8568MDS_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@) freescale
+
+stxgp3_config:		unconfig
+	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@) stx
+
+XPEDITE5200_config	\
+XPEDITE5370_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@) xes
 
+# special boards
+################
 MPC8536DS_NAND_config \
 MPC8536DS_SDCARD_config \
 MPC8536DS_SPIFLASH_config \
@@ -2261,9 +2089,6 @@ MPC8536DS_36BIT_config \
 MPC8536DS_config:       unconfig
 	@$(MKCONFIG) -n $@ -t $@ MPC8536DS powerpc mpc85xx mpc8536ds freescale
 
-MPC8540ADS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx mpc8540ads freescale
-
 MPC8540EVAL_config \
 MPC8540EVAL_33_config \
 MPC8540EVAL_66_config \
@@ -2278,9 +2103,6 @@ MPC8540EVAL_66_slave_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a MPC8540EVAL powerpc mpc85xx mpc8540eval
 
-MPC8560ADS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx mpc8560ads freescale
-
 MPC8541CDS_legacy_config \
 MPC8541CDS_config:	unconfig
 	@mkdir -p $(obj)include
@@ -2289,9 +2111,6 @@ MPC8541CDS_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a MPC8541CDS powerpc mpc85xx mpc8541cds freescale
 
-MPC8544DS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx mpc8544ds freescale
-
 MPC8548CDS_legacy_config \
 MPC8548CDS_config:	unconfig
 	@mkdir -p $(obj)include
@@ -2308,9 +2127,6 @@ MPC8555CDS_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a MPC8555CDS powerpc mpc85xx mpc8555cds freescale
 
-MPC8568MDS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx mpc8568mds freescale
-
 MPC8569MDS_ATM_config \
 MPC8569MDS_NAND_config \
 MPC8569MDS_config:	unconfig
@@ -2342,12 +2158,6 @@ P2020RDB_SDCARD_config \
 P2020RDB_SPIFLASH_config:	unconfig
 	@$(MKCONFIG) -n $@ -t $@ P1_P2_RDB powerpc mpc85xx p1_p2_rdb freescale
 
-PM854_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx pm854
-
-PM856_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx pm856
-
 sbc8540_config \
 sbc8540_33_config \
 sbc8540_66_config:	unconfig
@@ -2365,12 +2175,6 @@ sbc8560_33_config \
 sbc8560_66_config:	unconfig
 	@$(MKCONFIG) -n $@ -t $@ sbc8560 powerpc mpc85xx sbc8560
 
-socrates_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx socrates
-
-stxgp3_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx stxgp3 stx
-
 stxssa_config		\
 stxssa_4M_config:	unconfig
 	@mkdir -p $(obj)include
@@ -2396,18 +2200,27 @@ TQM8560_config:		unconfig
 	@echo "CONFIG_$(@:_config=) = y">>$(obj)include/config.mk;
 	@$(MKCONFIG) -n $@ -a TQM85xx powerpc mpc85xx tqm85xx tqc
 
-XPEDITE5200_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx xpedite5200 xes
-
-XPEDITE5370_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx xpedite5370 xes
-
 #########################################################################
 ## MPC86xx Systems
 #########################################################################
 
+# generic boards
+################
+
+sbc8641d_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc86xx $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
 MPC8610HPCD_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc86xx mpc8610hpcd freescale
+	@$(MKCONFIG) $@ powerpc mpc86xx $(call lcname,$@) freescale
+
+XPEDITE5170_config:	unconfig
+	@$(MKCONFIG) $@ powerpc mpc86xx $(call lcname,$@) xes
+
+# special boards
+################
 
 MPC8641HPCN_36BIT_config \
 MPC8641HPCN_config:    unconfig
@@ -2417,41 +2230,43 @@ MPC8641HPCN_config:    unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a MPC8641HPCN powerpc mpc86xx mpc8641hpcn freescale
 
-sbc8641d_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc86xx sbc8641d
-
-XPEDITE5170_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc86xx xpedite5170 xes
-
 #########################################################################
 ## 74xx/7xx Systems
 #########################################################################
 
-AmigaOneG3SE_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx AmigaOneG3SE MAI
+# generic boards
+################
+
+ppmc7xx_config: unconfig
+	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
 
-BAB7xx_config: unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx bab7xx eltec
+BAB7xx_config	\
+ELPPC_config:	unconfig
+	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) eltec
 
 CPCI750_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx cpci750 esd
+	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) esd
+
+mpc7448hpc2_config:  unconfig
+	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) freescale
 
-DB64360_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx db64360 Marvell
+AmigaOneG3SE_config:	unconfig
+	@$(MKCONFIG) $@ powerpc 74xx_7xx $(@:_config=) MAI
 
+DB64360_config	\
 DB64460_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx db64460 Marvell
+	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) Marvell
 
-ELPPC_config: unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx elppc eltec
+# special boards
+################
 
 EVB64260_config	\
 EVB64260_750CX_config:	unconfig
 	@$(MKCONFIG) -n $@ EVB64260 powerpc 74xx_7xx evb64260
 
-mpc7448hpc2_config:  unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx mpc7448hpc2 freescale
-
 P3G4_config: unconfig
 	@$(MKCONFIG) $@ powerpc 74xx_7xx evb64260
 
@@ -2469,9 +2284,6 @@ PCIPPC2_config \
 PCIPPC6_config: unconfig
 	@$(MKCONFIG) -n $@ $@ powerpc 74xx_7xx pcippc2
 
-ppmc7xx_config: unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx ppmc7xx
-
 ZUMA_config:	unconfig
 	@$(MKCONFIG) $@ powerpc 74xx_7xx evb64260
 
@@ -2482,40 +2294,89 @@ ZUMA_config:	unconfig
 ## StrongARM Systems
 #########################################################################
 
-assabet_config	:	unconfig
-	@$(MKCONFIG) $@ arm sa1100 assabet
-
-dnp1110_config	:	unconfig
-	@$(MKCONFIG) $@ arm sa1100 dnp1110
-
-gcplus_config	:	unconfig
-	@$(MKCONFIG) $@ arm sa1100 gcplus
-
-lart_config	:	unconfig
-	@$(MKCONFIG) $@ arm sa1100 lart
-
+# generic boards
+################
+assabet_config	\
+dnp1110_config	\
+gcplus_config	\
+lart_config	\
 shannon_config	:	unconfig
-	@$(MKCONFIG) $@ arm sa1100 shannon
+	@$(MKCONFIG) $@ arm sa1100 $(call lcname,$@)
 
 #########################################################################
 ## ARM92xT Systems
 #########################################################################
 
+# generic boards
+################
+
+edb9301_config \
+edb9302_config \
+edb9302a_config \
+edb9307_config \
+edb9307a_config \
+edb9312_config \
+edb9315_config \
+edb9315a_config: unconfig
+	@$(MKCONFIG) -n $@ -t $@ edb93xx arm arm920t edb93xx NULL ep93xx
+
+mx1ads_config	\
+mx1fs2_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL imx
+
+sbc2410x_config: unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL s3c24x0
+
+scb9328_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL imx
+
+cm4008_config	\
+cm41xx_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL ks8695
+
+netstar_config		\
+voiceblue_config:	unconfig
+	@$(MKCONFIG) $@ arm arm925t $(call lcname,$@)
+
+# vendor specific boards (sorted by vendor)
+###########################################
+
 a320evb_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t a320evb faraday a320
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) faraday a320
+
+smdk2400_config		\
+smdk2410_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) samsung s3c24x0
 
 #########################################################################
 ## Atmel AT91RM9200 Systems
 #########################################################################
 
-at91rm9200dk_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t at91rm9200dk atmel at91rm9200
+# generic boards
+################
+
+cmc_pu2_config	\
+csb637_config	\
+kb9202_config	\
+m501sk_config	\
+mp2usb_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL at91rm9200
+
+# vendor specific boards (sorted by vendor)
+###########################################
 
+at91rm9200dk_config	\
 at91rm9200ek_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t at91rm9200ek atmel at91rm9200
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) atmel at91rm9200
+
+eb_cpux9k2_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) BuS at91
+
+omap1510inn_config :	unconfig
+	@$(MKCONFIG) $@ arm arm925t $(call lcname,$@) ti
 
-cmc_pu2_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t cmc_pu2 NULL at91rm9200
+# special boards
+################
 
 CPUAT91_RAM_config \
 CPUAT91_config	:	unconfig
@@ -2523,30 +2384,45 @@ CPUAT91_config	:	unconfig
 	@echo "#define CONFIG_$(@:_config=) 1"	>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a cpuat91 arm arm920t cpuat91 eukrea at91rm9200
 
-csb637_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t csb637 NULL at91rm9200
-
-eb_cpux9k2_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t eb_cpux9k2 BuS at91
-
-kb9202_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t kb9202 NULL at91rm9200
-
-m501sk_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t m501sk NULL at91rm9200
-
-mp2usb_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t mp2usb NULL at91rm9200
-
 #########################################################################
 ## ARM926EJ-S Systems
 #########################################################################
 
+# generic boards
+################
+
 afeb9260_config:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs afeb9260 NULL at91
+	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) NULL at91
+
+# vendor specific boards (sorted by vendor)
+###########################################
 
 at91cap9adk_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs at91cap9adk atmel at91
+	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) atmel at91
+
+meesc_config	\
+otc570_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) esd at91
+
+guruplug_config		\
+mv88f6281gtw_ge_config	\
+openrd_base_config	\
+rd6281a_config		\
+sheevaplug_config:	unconfig
+	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) Marvell kirkwood
+
+VCMA9_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) mpl s3c24x0
+
+pm9261_config	\
+pm9263_config	:	unconfig
+	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) ronetix at91
+
+omap5912osk_config :	unconfig
+	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) ti omap
+
+# special boards
+################
 
 at91sam9260ek_nandflash_config \
 at91sam9260ek_dataflash_cs0_config \
@@ -2647,12 +2523,6 @@ CPU9260_config	:	unconfig
 	@echo "#define CONFIG_$(@:_config=) 1" >$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a cpu9260 arm arm926ejs cpu9260 eukrea at91
 
-meesc_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs meesc esd at91
-
-pm9261_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs pm9261 ronetix at91
-
 at91sam9m10g45ek_nandflash_config \
 at91sam9m10g45ek_dataflash_config \
 at91sam9m10g45ek_dataflash_cs0_config \
@@ -2674,12 +2544,6 @@ at91sam9g45ekes_config	:	unconfig
 	fi;
 	@$(MKCONFIG) -n $@ -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91
 
-otc570_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs otc570 esd at91
-
-pm9263_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs pm9263 ronetix at91
-
 SBC35_A9G20_NANDFLASH_config \
 SBC35_A9G20_EEPROM_config \
 SBC35_A9G20_config	:	unconfig
@@ -2735,9 +2599,6 @@ davinci_dm6467evm_config	:	unconfig
 	@$(MKCONFIG) -n $@ $@ arm arm926ejs \
 		$(subst davinci_,,$(@:_config=)) davinci davinci
 
-guruplug_config: unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
-
 magnesium_config	\
 imx27lite_config:	unconfig
 	@$(MKCONFIG) $@ arm arm926ejs imx27lite logicpd mx27
@@ -2746,18 +2607,6 @@ lpd7a400_config \
 lpd7a404_config:	unconfig
 	@$(MKCONFIG) $@ arm lh7a40x lpd7a40x
 
-mv88f6281gtw_ge_config: unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
-
-mx1ads_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t mx1ads NULL imx
-
-mx1fs2_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t mx1fs2 NULL imx
-
-netstar_config:		unconfig
-	@$(MKCONFIG) $@ arm arm925t netstar
-
 nhk8815_config \
 nhk8815_onenand_config:	unconfig
 	@mkdir -p $(obj)include
@@ -2767,9 +2616,6 @@ nhk8815_onenand_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a nhk8815 arm arm926ejs nhk8815 st nomadik
 
-omap1510inn_config :	unconfig
-	@$(MKCONFIG) $@ arm arm925t omap1510inn ti
-
 xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,,$(subst _cs_autoboot,,$(subst _config,,$1))))
 
 omap1610inn_config \
@@ -2790,12 +2636,6 @@ omap1610h2_cs_autoboot_config:	unconfig
 	fi;
 	@$(MKCONFIG) -n $@ -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn ti omap
 
-omap5912osk_config :	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs omap5912osk ti omap
-
-openrd_base_config: unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
-
 omap730p2_config \
 omap730p2_cs0boot_config \
 omap730p2_cs3boot_config :	unconfig
@@ -2807,24 +2647,6 @@ omap730p2_cs3boot_config :	unconfig
 	fi;
 	@$(MKCONFIG) -n $@ -a omap730p2 arm arm926ejs omap730p2 ti omap
 
-rd6281a_config: unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
-
-sbc2410x_config: unconfig
-	@$(MKCONFIG) $@ arm arm920t sbc2410x NULL s3c24x0
-
-scb9328_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t scb9328 NULL imx
-
-sheevaplug_config: unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(@:_config=) Marvell kirkwood
-
-smdk2400_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t smdk2400 samsung s3c24x0
-
-smdk2410_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t smdk2410 samsung s3c24x0
-
 spear300_config \
 spear310_config \
 spear320_config :	unconfig
@@ -2873,135 +2695,113 @@ tx25_config	: unconfig
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 	@$(MKCONFIG) $@ arm arm926ejs tx25 karo mx25
 
-VCMA9_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t vcma9 mpl s3c24x0
-
 #########################################################################
 # ARM supplied Versatile development boards
 #########################################################################
 
-cm4008_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t cm4008 NULL ks8695
-
-cm41xx_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t cm41xx NULL ks8695
-
 versatile_config	\
 versatileab_config	\
 versatilepb_config :	unconfig
 	@board/armltd/versatile/split_by_variant.sh $@
 
-voiceblue_config:	unconfig
-	@$(MKCONFIG) $@ arm arm925t voiceblue
-
 #########################################################################
 ## S3C44B0 Systems
 #########################################################################
 
 B2_config	:	unconfig
-	@$(MKCONFIG) $@ arm s3c44b0 B2 dave
+	@$(MKCONFIG) $@ arm s3c44b0 $(call ucname,$@) dave
 
 #########################################################################
 ## ARM720T Systems
 #########################################################################
 
-armadillo_config:	unconfig
-	@$(MKCONFIG) $@ arm arm720t armadillo
-
-ep7312_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm720t ep7312
-
-impa7_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm720t impa7
+# generic boards
+################
 
+armadillo_config	\
+ep7312_config		\
+impa7_config		\
 modnet50_config :	unconfig
-	@$(MKCONFIG) $@ arm arm720t modnet50
+	@$(MKCONFIG) $@ arm arm720t $(call lcname,$@)
 
 evb4510_config :	unconfig
-	@$(MKCONFIG) $@ arm arm720t evb4510 NULL s3c4510b
+	@$(MKCONFIG) $@ arm arm720t $(call lcname,$@) NULL s3c4510b
 
 lpc2292sodimm_config:	unconfig
-	@$(MKCONFIG) $@ arm arm720t lpc2292sodimm NULL lpc2292
+	@$(MKCONFIG) $@ arm arm720t $(call lcname,$@) NULL lpc2292
+
+# vendor specific boards (sorted by vendor)
+###########################################
 
 SMN42_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm720t SMN42 siemens lpc2292
+	@$(MKCONFIG) $@ arm arm720t $(call ucname,$@) siemens lpc2292
 
 #########################################################################
 ## ARM CORTEX Systems
 #########################################################################
+omapname = $(shell echo $(1) | sed -e 's/omap[0-9]_//' -e 's/\(.*\)_config/\L\1/')
 
-devkit8000_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 devkit8000 timll omap3
-
-omap3_beagle_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 beagle ti omap3
-
-omap3_overo_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 overo NULL omap3
-
-omap3_evm_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 evm ti omap3
+# generic boards
+################
 
+omap3_overo_config	\
 omap3_pandora_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 pandora NULL omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 $(call omapname,$@) NULL omap3
 
-omap3_sdp3430_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 sdp3430 ti omap3
+# vendor specific boards (sorted by vendor)
+###########################################
 
-omap3_zoom1_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 zoom1 logicpd omap3
+mx51evk_config	: unconfig
+	@$(MKCONFIG) $@ arm arm_cortexa8 $(call lcname,$@) freescale mx51
 
+omap3_zoom1_config	\
 omap3_zoom2_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 zoom2 logicpd omap3
+	@$(MKCONFIG) $@ arm arm_cortexa8 $(call omapname,$@) logicpd omap3
 
 smdkc100_config:	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 smdkc100 samsung s5pc1xx
+	@$(MKCONFIG) $@ arm arm_cortexa8 $(call lcname,$@) samsung s5pc1xx
+
+omap3_beagle_config	\
+omap3_evm_config	\
+omap3_sdp3430_config :	unconfig
+	@$(MKCONFIG) $@ arm arm_cortexa8 $(call omapname,$@) ti omap3
+
+devkit8000_config :	unconfig
+	@$(MKCONFIG) $@ arm arm_cortexa8 $(call lcname,$@) timll omap3
 
 #########################################################################
 ## XScale Systems
 #########################################################################
 
-actux1_config	:	unconfig
-	@$(MKCONFIG) $@ arm ixp actux1
-
-actux2_config	:	unconfig
-	@$(MKCONFIG) $@ arm ixp actux2
-
-actux3_config	:	unconfig
-	@$(MKCONFIG) $@ arm ixp actux3
-
-actux4_config	:	unconfig
-	@$(MKCONFIG) $@ arm ixp actux4
-
-cerf250_config :	unconfig
-	@$(MKCONFIG) $@ arm pxa cerf250
-
-cradle_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa cradle
-
-csb226_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa csb226
-
-delta_config :	unconfig
-	@$(MKCONFIG) $@ arm pxa delta
-
-innokom_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa innokom
-
-ixdp425_config	:	unconfig
-	@$(MKCONFIG) $@ arm ixp ixdp425
+# generic boards
+################
 
+actux1_config	\
+actux2_config	\
+actux3_config	\
+actux4_config	\
+ixdp425_config	\
 ixdpg425_config	:	unconfig
-	@$(MKCONFIG) $@ arm ixp ixdp425
-
-lubbock_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa lubbock
-
-pleb2_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa pleb2
+	@$(MKCONFIG) $@ arm ixp $(call lcname,$@)
+
+cerf250_config	\
+cradle_config	\
+csb226_config	\
+delta_config	\
+innokom_config	\
+lubbock_config	\
+pleb2_config	\
+logodl_config	\
+pxa255_idp_config \
+wepep250_config	\
+xaeniax_config	\
+xm250_config	\
+xsengine_config \
+zylonite_config :
+	@$(MKCONFIG) $@ arm pxa $(call lcname,$@)
 
-logodl_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa logodl
+# special boards
+################
 
 pdnb3_config \
 scpu_config:	unconfig
@@ -3011,9 +2811,6 @@ scpu_config:	unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a pdnb3 arm ixp pdnb3 prodrive
 
-pxa255_idp_config:	unconfig
-	@$(MKCONFIG) $@ arm pxa pxa255_idp
-
 polaris_config \
 trizepsiv_config	:	unconfig
 	@mkdir -p $(obj)include
@@ -3022,24 +2819,30 @@ trizepsiv_config	:	unconfig
 	fi;
 	@$(MKCONFIG) -n $@ -a trizepsiv arm pxa trizepsiv
 
-wepep250_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa wepep250
+#########################################################################
+## ARM1136 Systems
+#########################################################################
 
-xaeniax_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa xaeniax
+# generic boards
+################
 
-xm250_config	:	unconfig
-	@$(MKCONFIG) $@ arm pxa xm250
+# vendor specific boards (sorted by vendor)
+###########################################
 
-xsengine_config :	unconfig
-	@$(MKCONFIG) $@ arm pxa xsengine
+qong_config		: unconfig
+	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) davedenx mx31
 
-zylonite_config :
-	@$(MKCONFIG) $@ arm pxa zylonite
+mx31ads_config		: unconfig
+	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) freescale mx31
 
-#########################################################################
-## ARM1136 Systems
-#########################################################################
+imx31_litekit_config	: unconfig
+	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) logicpd mx31
+
+omap2420h4_config	: unconfig
+	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) ti omap24xx
+
+# special boards
+################
 
 apollon_config		: unconfig
 	@mkdir -p $(obj)include
@@ -3047,9 +2850,6 @@ apollon_config		: unconfig
 	@echo "CONFIG_ONENAND_U_BOOT = y" >> $(obj)include/config.mk
 	@$(MKCONFIG) $@ arm arm1136 apollon NULL omap24xx
 
-imx31_litekit_config	: unconfig
-	@$(MKCONFIG) $@ arm arm1136 imx31_litekit logicpd mx31
-
 imx31_phycore_eet_config \
 imx31_phycore_config	: unconfig
 	@mkdir -p $(obj)include
@@ -3058,9 +2858,6 @@ imx31_phycore_config	: unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a imx31_phycore arm arm1136 imx31_phycore NULL mx31
 
-mx31ads_config		: unconfig
-	@$(MKCONFIG) $@ arm arm1136 mx31ads freescale mx31
-
 mx31pdk_config \
 mx31pdk_nand_config	: unconfig
 	@mkdir -p $(obj)include
@@ -3072,15 +2869,6 @@ mx31pdk_nand_config	: unconfig
 	fi
 	@$(MKCONFIG) -n $@ -a mx31pdk arm arm1136 mx31pdk freescale mx31
 
-mx51evk_config	: unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 mx51evk freescale mx51
-
-omap2420h4_config	: unconfig
-	@$(MKCONFIG) $@ arm arm1136 omap2420h4 ti omap24xx
-
-qong_config		: unconfig
-	@$(MKCONFIG) $@ arm arm1136 qong davedenx mx31
-
 #########################################################################
 ## ARM1176 Systems
 #########################################################################
@@ -3103,14 +2891,13 @@ smdk6400_config	:	unconfig
 #########################################################################
 ## AMD SC520 CDP
 #########################################################################
-eNET_config	:	unconfig
-	@$(MKCONFIG) $@ i386 i386 eNET NULL sc520
-
-sc520_cdp_config	:	unconfig
-	@$(MKCONFIG) $@ i386 i386 sc520_cdp NULL sc520
 
+# generic boards
+################
+eNET_config		\
+sc520_cdp_config	\
 sc520_spunk_config	:	unconfig
-	@$(MKCONFIG) $@ i386 i386 sc520_spunk NULL sc520
+	@$(MKCONFIG) $@ i386 i386 $(call lcname,$@) NULL sc520
 
 sc520_spunk_rel_config	:	unconfig
 	@$(MKCONFIG) $@ i386 i386 sc520_spunk NULL sc520
@@ -3122,6 +2909,15 @@ sc520_spunk_rel_config	:	unconfig
 ## MIPS32 4Kc
 #########################################################################
 
+# generic boards
+################
+
+tb0229_config: unconfig
+	@$(MKCONFIG) $@ mips mips $(call lcname,$@)
+
+# special boards
+################
+
 incaip_100MHz_config	\
 incaip_133MHz_config	\
 incaip_150MHz_config	\
@@ -3135,9 +2931,6 @@ incaip_config: unconfig
 		echo "#define CPU_CLOCK_RATE 150000000" >>$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a incaip mips mips incaip
 
-tb0229_config: unconfig
-	@$(MKCONFIG) $@ mips mips tb0229
-
 vct_premium_config		\
 vct_premium_small_config	\
 vct_premium_onenand_config	\
@@ -3222,20 +3015,17 @@ purple_config :		unconfig
 ## Nios-II
 #########################################################################
 
-EP1C20_config : unconfig
-	@$(MKCONFIG) $@ nios2 nios2 ep1c20 altera
-
-EP1S10_config : unconfig
-	@$(MKCONFIG) $@ nios2 nios2 ep1s10 altera
+# vendor specific boards (sorted by vendor)
+###########################################
 
-EP1S40_config : unconfig
-	@$(MKCONFIG) $@ nios2 nios2 ep1s40 altera
+EP1C20_config	\
+EP1S10_config	\
+EP1S40_config	: unconfig
+	@$(MKCONFIG) $@ nios2 nios2 $(call lcname,$@) altera
 
-PK1C20_config : unconfig
-	@$(MKCONFIG) $@ nios2 nios2 pk1c20 psyent
-
-PCI5441_config : unconfig
-	@$(MKCONFIG) $@ nios2 nios2 pci5441 psyent
+PK1C20_config	\
+PCI5441_config	: unconfig
+	@$(MKCONFIG) $@ nios2 nios2 $(call lcname,$@) psyent
 
 # nios2 generic boards
 NIOS2_GENERIC = nios2-generic
@@ -3384,33 +3174,21 @@ espt_config  :   unconfig
 #========================================================================
 
 #########################################################################
-## LEON3
+## LEON2
 #########################################################################
 
-# Gaisler GR-XC3S-1500 board
-gr_xc3s_1500_config : unconfig
-	@$(MKCONFIG) $@ sparc leon3 gr_xc3s_1500 gaisler
-
-# Gaisler GR-CPCI-AX2000 board, a General purpose FPGA-AX system
-gr_cpci_ax2000_config : unconfig
-	@$(MKCONFIG) $@ sparc leon3 gr_cpci_ax2000 gaisler
-
-# Gaisler GRLIB template design (GPL SPARC/LEON3) for Altera NIOS
-# Development board Stratix II edition, FPGA Device EP2S60.
-gr_ep2s60_config: unconfig
-	@$(MKCONFIG) $@ sparc leon3 gr_ep2s60 gaisler
-
-# Gaisler LEON3 GRSIM simulator
-grsim_config : unconfig
-	@$(MKCONFIG) $@ sparc leon3 grsim gaisler
+grsim_leon2_config : unconfig
+	@$(MKCONFIG) $@ sparc leon2 $(call lcname,$@) gaisler
 
 #########################################################################
-## LEON2
+## LEON3
 #########################################################################
 
-# Gaisler LEON2 GRSIM simulator
-grsim_leon2_config : unconfig
-	@$(MKCONFIG) $@ sparc leon2 grsim_leon2 gaisler
+gr_xc3s_1500_config	\
+gr_cpci_ax2000_config	\
+gr_ep2s60_config	\
+grsim_config	:	unconfig
+	@$(MKCONFIG) $@ sparc leon3 $(call lcname,$@) gaisler
 
 #########################################################################
 #########################################################################
-- 
cgit v1.1


From a6862bc123a9e6c93583879973679b0c5941a418 Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Thu, 27 May 2010 23:18:36 +0200
Subject: Makefile/mkconfig: read simple board configurations from boards.cfg

Instead of adding explicit build rules for each and every board to the
top level Makefile (which makes it grow and grow), we now provide a
simple default rule and extend the "mkconfig" script to read board
configurations from a plain text file (table), "boards.cfg".

For simple boards it is now sufficient to add a single line of text to
the "boards.cfg" file, no changes to the top level Makefile are needed
any more.

To make the table better readable, change the notation for unused
fields from "NULL" into "-".

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Mike Frysinger <vapier@gentoo.org>
---
 Makefile   | 823 ++-----------------------------------------------------------
 boards.cfg | 356 ++++++++++++++++++++++++++
 mkconfig   |  72 ++++--
 3 files changed, 431 insertions(+), 820 deletions(-)
 create mode 100644 boards.cfg

diff --git a/Makefile b/Makefile
index 42d807b..9f7883a 100644
--- a/Makefile
+++ b/Makefile
@@ -475,8 +475,11 @@ unconfig:
 		$(obj)board/*/config.tmp $(obj)board/*/*/config.tmp \
 		$(obj)include/autoconf.mk $(obj)include/autoconf.mk.dep
 
-%: %_config
-	$(MAKE)
+%_config::	unconfig
+	@$(MKCONFIG) -A $(@:_config=)
+
+##%: %_config
+##	$(MAKE)
 
 #
 # Functions to generate common board directory names
@@ -489,50 +492,9 @@ ucname	= $(shell echo $(1) | sed -e 's/\(.*\)_config/\U\1/')
 #========================================================================
 
 #########################################################################
-## MPC5xx Systems
-#########################################################################
-
-cmi_mpc5xx_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xx cmi
-
-PATI_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xx pati mpl
-
-#########################################################################
 ## MPC5xxx Systems
 #########################################################################
 
-# generic boards
-################
-BC3450_config	\
-canmb_config	\
-cm5200_config	\
-hmi1001_config	\
-jupiter_config	\
-inka4x0_config	\
-ipek01_config	\
-motionpro_config\
-mucmc52_config	\
-munices_config	\
-o2dnt_config	\
-uc101_config	\
-v38b_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-cpci5200_config	\
-mecp5200_config	\
-pf5200_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx $(call lcname,$@) esd
-
-aev_config	\
-smmaco4_config	\
-spieval_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc5xxx tqm5200 tqc
-
-# special boards
-################
 digsy_mtc_config \
 digsy_mtc_LOWBOOT_config	\
 digsy_mtc_RAMBOOT_config:	unconfig
@@ -717,21 +679,6 @@ TQM5200_STK100_config:	unconfig
 ## MPC512x Systems
 #########################################################################
 
-# generic boards
-################
-pdm360ng_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc512x $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-aria_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc512x aria davedenx
-
-mecp5123_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc512x mecp5123 esd
-
-# special boards
-################
 mpc5121ads_config \
 mpc5121ads_rev2_config	\
 	: unconfig
@@ -745,80 +692,6 @@ mpc5121ads_rev2_config	\
 ## MPC8xx Systems
 #########################################################################
 
-# generic boards
-################
-
-c2mon_config		\
-EP88x_config		\
-ESTEEM192E_config	\
-ETX094_config		\
-FLAGADM_config		\
-GENIETV_config		\
-GTH_config		\
-hermes_config		\
-IP860_config		\
-LANTEC_config		\
-lwmon_config		\
-NX823_config		\
-quantum_config		\
-R360MPI_config		\
-RBC823_config		\
-rmu_config		\
-spc1920_config		\
-svm_sc8xx_config	\
-uc100_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx $(call lcname,$@)
-
-RPXClassic_config	\
-RPXlite_config		\
-RRvision_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx $(@:_config=)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-MHPC_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx mhpc eltec
-
-TOP860_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx top860 emk
-
-kmsupx4_config	\
-mgsuvd_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx km8xx keymile
-
-KUP4K_config	\
-KUP4X_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx $(call lcname,$@) kup
-
-ELPT860_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx elpt860 LEOX
-
-stxxtc_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx stxxtc stx
-
-HMI10_config	\
-SM850_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx tqm8xx tqc
-
-CCM_config	\
-IAD210_config	\
-pcu_e_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx $(@:_config=) siemens
-
-QS823_config	\
-QS850_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx qs850 snmc
-
-QS860T_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx qs860t snmc
-
-AMX860_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8xx amx860 westel
-
-# special boards
-################
-
 Adder87x_config \
 AdderII_config	\
 AdderUSB_config	\
@@ -829,9 +702,6 @@ Adder_config	\
 		@echo "#define CONFIG_MPC852T" > $(obj)include/config.h)
 	@$(MKCONFIG) -n $@ -a Adder powerpc mpc8xx adder
 
-cogent_mpc8xx_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) powerpc mpc8xx cogent
-
 ADS860_config	  \
 FADS823_config	  \
 FADS850SAR_config \
@@ -1031,103 +901,6 @@ wtk_config:	unconfig
 ## PPC4xx Systems
 #########################################################################
 
-# generic boards
-################
-
-csb272_config	\
-csb472_config	\
-ERIC_config	\
-G2000_config	\
-JSE_config	\
-korat_config	\
-lwmon5_config	\
-ML2_config	\
-pcs440ep_config	\
-quad100hd_config\
-sbc405_config	\
-sc3_config	\
-zeus_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-acadia_config	\
-bamboo_config	\
-bubinga_config	\
-ebony_config	\
-katmai_config	\
-luan_config	\
-makalu_config	\
-ocotea_config	\
-redwood_config	\
-taihu_config	\
-taishan_config	\
-yucca_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) amcc
-
-AP1000_config:unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) amirix
-
-ADCIOP_config	\
-APC405_config	\
-AR405_config	\
-ASH405_config	\
-CANBT_config	\
-CMS700_config	\
-CPCI2DP_config	\
-CPCIISER4_config\
-DASA_SIM_config	\
-DP405_config	\
-DU405_config	\
-DU440_config	\
-HH405_config	\
-HUB405_config	\
-PCI405_config	\
-PLU405_config	\
-PMC405_config	\
-PMC405DE_config	\
-PMC440_config	\
-VOH405_config	\
-VOM405_config	\
-WUH405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) esd
-
-CRAYL1_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx L1 cray
-
-dlvision_config		\
-gdppc440etx_config	\
-neo_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) gdsys
-
-icon_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) mosaixtech
-
-MIP405_config	\
-PIP405_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) mpl
-
-hcu4_config	\
-hcu5_config	\
-mcu25_config:  unconfig
-	@mkdir -p $(obj)board/netstal/common
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) netstal
-
-alpr_config	\
-p3p440_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) prodrive
-
-KAREF_config	\
-METROBOX_config: unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) sandburst
-
-XPEDITE1000_config:	unconfig
-	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) xes
-
-# special boards
-################
-
 acadia_nand_config:	unconfig
 	@mkdir -p $(obj)include $(obj)board/amcc/acadia
 	@mkdir -p $(obj)nand_spl/board/amcc/acadia
@@ -1209,6 +982,12 @@ devconcenter_config:	unconfig
 		tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a intip powerpc ppc4xx intip gdsys
 
+hcu4_config    \
+hcu5_config    \
+mcu25_config:  unconfig
+	@mkdir -p $(obj)board/netstal/common
+	@$(MKCONFIG) $@ powerpc ppc4xx $(call lcname,$@) netstal
+
 # Kilauea & Haleakala images are identical (recognized via PVR)
 kilauea_config \
 haleakala_config: unconfig
@@ -1367,47 +1146,9 @@ yellowstone_config: unconfig
 	@$(MKCONFIG) -n $@ -a yosemite powerpc ppc4xx yosemite amcc
 
 #########################################################################
-## MPC8220 Systems
-#########################################################################
-
-# generic boards
-################
-sorcery_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8220 $(call lcname,$@)
-
-Alaska8220_config	\
-Yukon8220_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8220 alaska
-
-#########################################################################
 ## MPC824x Systems
 #########################################################################
 
-# generic boards
-################
-A3000_config	\
-barco_config	\
-BMW_config	\
-CU824_config	\
-HIDDEN_DRAGON_config \
-MOUSSE_config	\
-MUSENKI_config	\
-MVBLUE_config	\
-OXC_config	\
-PN62_config	\
-sbc8240_config	\
-utx8245_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-debris_config	\
-kvme080_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc824x $(call lcname,$@) etin
-
-# special boards
-################
 eXalion_config: unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc824x eXalion
 
@@ -1444,41 +1185,6 @@ Sandpoint8245_config: unconfig
 ## MPC8260 Systems
 #########################################################################
 
-# generic boards
-################
-atc_config		\
-ep8260_config		\
-ep82xxm_config		\
-gw8260_config		\
-hymod_config		\
-IDS8247_config		\
-IPHASE4539_config	\
-ppmc8260_config		\
-RPXsuper_config		\
-rsdproto_config		\
-sacsng_config		\
-sbc8260_config		\
-ZPC1900_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-MPC8266ADS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 $(call lcname,$@) freescale
-
-mgcoge_config	:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 $(call lcname,$@) keymile
-
-SCM_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc8260 $(call ucname,$@) siemens
-
-TQM8272_config: unconfig
-	@$(MKCONFIG) TQM8272 powerpc mpc8260 $(call lcname,$@) tqc
-
-# special boards
-################
-
 cogent_mpc8260_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) powerpc mpc8260 cogent
 
@@ -1661,35 +1367,6 @@ VoVPN-GW_100MHz_config:		unconfig
 ## Coldfire
 #########################################################################
 
-# generic boards
-################
-
-idmr_config:		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-TASREG_config :		unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@) esd
-
-M5208EVBE_config	\
-M5249EVB_config		\
-M5253DEMO_config	\
-M5253EVBE_config	\
-M5271EVB_config		\
-M5272C3_config		\
-M5275EVB_config		\
-M5282EVB_config		\
-M53017EVB_config:	unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@) freescale
-
-EP2500_config	:	unconfig
-	@$(MKCONFIG) $@ m68k mcf52x2 $(call lcname,$@) Mercury
-
-# special boards
-################
-
 astro_mcf5373l_config \
 astro_mcf5373l_RAM_config :	unconfig
 	@$(MKCONFIG) -n $@ -t $@ astro_mcf5373l m68k mcf532x mcf5373l astro
@@ -1896,29 +1573,6 @@ M5485HFE_config :	unconfig
 ## MPC83xx Systems
 #########################################################################
 
-# generic boards
-################
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-MPC8323ERDB_config	\
-MPC8349EMDS_config	\
-MPC837XERDB_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) freescale
-
-kmeter1_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) keymile
-
-MVBLM7_config: unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) matrix_vision
-
-TQM834x_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc83xx $(call lcname,$@) tqc
-
-# special boards
-################
-
 MPC8313ERDB_33_config \
 MPC8313ERDB_66_config \
 MPC8313ERDB_NAND_33_config \
@@ -2055,33 +1709,6 @@ vme8349_config:		unconfig
 ## MPC85xx Systems
 #########################################################################
 
-# generic boards
-################
-
-ATUM8548_config		\
-PM854_config		\
-PM856_config		\
-socrates_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-MPC8540ADS_config	\
-MPC8560ADS_config	\
-MPC8544DS_config	\
-MPC8568MDS_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@) freescale
-
-stxgp3_config:		unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@) stx
-
-XPEDITE5200_config	\
-XPEDITE5370_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc85xx $(call lcname,$@) xes
-
-# special boards
-################
 MPC8536DS_NAND_config \
 MPC8536DS_SDCARD_config \
 MPC8536DS_SPIFLASH_config \
@@ -2204,24 +1831,6 @@ TQM8560_config:		unconfig
 ## MPC86xx Systems
 #########################################################################
 
-# generic boards
-################
-
-sbc8641d_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc86xx $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-MPC8610HPCD_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc86xx $(call lcname,$@) freescale
-
-XPEDITE5170_config:	unconfig
-	@$(MKCONFIG) $@ powerpc mpc86xx $(call lcname,$@) xes
-
-# special boards
-################
-
 MPC8641HPCN_36BIT_config \
 MPC8641HPCN_config:    unconfig
 	@mkdir -p $(obj)include
@@ -2234,42 +1843,10 @@ MPC8641HPCN_config:    unconfig
 ## 74xx/7xx Systems
 #########################################################################
 
-# generic boards
-################
-
-ppmc7xx_config: unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-BAB7xx_config	\
-ELPPC_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) eltec
-
-CPCI750_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) esd
-
-mpc7448hpc2_config:  unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) freescale
-
-AmigaOneG3SE_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx $(@:_config=) MAI
-
-DB64360_config	\
-DB64460_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx $(call lcname,$@) Marvell
-
-# special boards
-################
-
 EVB64260_config	\
 EVB64260_750CX_config:	unconfig
 	@$(MKCONFIG) -n $@ EVB64260 powerpc 74xx_7xx evb64260
 
-P3G4_config: unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx evb64260
-
 p3m750_config	\
 p3m7448_config:		unconfig
 	@mkdir -p $(obj)include
@@ -2284,100 +1861,14 @@ PCIPPC2_config \
 PCIPPC6_config: unconfig
 	@$(MKCONFIG) -n $@ $@ powerpc 74xx_7xx pcippc2
 
-ZUMA_config:	unconfig
-	@$(MKCONFIG) $@ powerpc 74xx_7xx evb64260
-
 #========================================================================
 # ARM
 #========================================================================
-#########################################################################
-## StrongARM Systems
-#########################################################################
-
-# generic boards
-################
-assabet_config	\
-dnp1110_config	\
-gcplus_config	\
-lart_config	\
-shannon_config	:	unconfig
-	@$(MKCONFIG) $@ arm sa1100 $(call lcname,$@)
-
-#########################################################################
-## ARM92xT Systems
-#########################################################################
-
-# generic boards
-################
-
-edb9301_config \
-edb9302_config \
-edb9302a_config \
-edb9307_config \
-edb9307a_config \
-edb9312_config \
-edb9315_config \
-edb9315a_config: unconfig
-	@$(MKCONFIG) -n $@ -t $@ edb93xx arm arm920t edb93xx NULL ep93xx
-
-mx1ads_config	\
-mx1fs2_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL imx
-
-sbc2410x_config: unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL s3c24x0
-
-scb9328_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL imx
-
-cm4008_config	\
-cm41xx_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL ks8695
-
-netstar_config		\
-voiceblue_config:	unconfig
-	@$(MKCONFIG) $@ arm arm925t $(call lcname,$@)
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-a320evb_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) faraday a320
-
-smdk2400_config		\
-smdk2410_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) samsung s3c24x0
 
 #########################################################################
 ## Atmel AT91RM9200 Systems
 #########################################################################
 
-# generic boards
-################
-
-cmc_pu2_config	\
-csb637_config	\
-kb9202_config	\
-m501sk_config	\
-mp2usb_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) NULL at91rm9200
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-at91rm9200dk_config	\
-at91rm9200ek_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) atmel at91rm9200
-
-eb_cpux9k2_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) BuS at91
-
-omap1510inn_config :	unconfig
-	@$(MKCONFIG) $@ arm arm925t $(call lcname,$@) ti
-
-# special boards
-################
-
 CPUAT91_RAM_config \
 CPUAT91_config	:	unconfig
 	@mkdir -p $(obj)include
@@ -2388,42 +1879,6 @@ CPUAT91_config	:	unconfig
 ## ARM926EJ-S Systems
 #########################################################################
 
-# generic boards
-################
-
-afeb9260_config:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) NULL at91
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-at91cap9adk_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) atmel at91
-
-meesc_config	\
-otc570_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) esd at91
-
-guruplug_config		\
-mv88f6281gtw_ge_config	\
-openrd_base_config	\
-rd6281a_config		\
-sheevaplug_config:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) Marvell kirkwood
-
-VCMA9_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm920t $(call lcname,$@) mpl s3c24x0
-
-pm9261_config	\
-pm9263_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) ronetix at91
-
-omap5912osk_config :	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs $(call lcname,$@) ti omap
-
-# special boards
-################
-
 at91sam9260ek_nandflash_config \
 at91sam9260ek_dataflash_cs0_config \
 at91sam9260ek_dataflash_cs1_config \
@@ -2599,14 +2054,6 @@ davinci_dm6467evm_config	:	unconfig
 	@$(MKCONFIG) -n $@ $@ arm arm926ejs \
 		$(subst davinci_,,$(@:_config=)) davinci davinci
 
-magnesium_config	\
-imx27lite_config:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs imx27lite logicpd mx27
-
-lpd7a400_config \
-lpd7a404_config:	unconfig
-	@$(MKCONFIG) $@ arm lh7a40x lpd7a40x
-
 nhk8815_config \
 nhk8815_onenand_config:	unconfig
 	@mkdir -p $(obj)include
@@ -2655,9 +2102,6 @@ spear320_config :	unconfig
 spear600_config :	unconfig
 	@$(MKCONFIG) -n $@ -t $@ spear6xx arm arm926ejs $(@:_config=) spear spear
 
-suen3_config:	unconfig
-	@$(MKCONFIG) $@ arm arm926ejs km_arm keymile kirkwood
-
 SX1_stdout_serial_config \
 SX1_config:		unconfig
 	@mkdir -p $(obj)include
@@ -2689,12 +2133,22 @@ trab_old_config:	unconfig
 		  echo "#define CONFIG_RAM_16MB"   >>$(obj)include/config.h ; \
 		  echo "TEXT_BASE = 0x0CF40000" >$(obj)board/trab/config.tmp ; \
 		}
-	@$(MKCONFIG) -n $@ -a trab arm arm920t trab NULL s3c24x0
+	@$(MKCONFIG) -n $@ -a trab arm arm920t trab - s3c24x0
 
 tx25_config	: unconfig
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 	@$(MKCONFIG) $@ arm arm926ejs tx25 karo mx25
 
+edb9301_config \
+edb9302_config \
+edb9302a_config \
+edb9307_config \
+edb9307a_config \
+edb9312_config \
+edb9315_config \
+edb9315a_config: unconfig
+	@$(MKCONFIG) -n $@ -t $(@:_config=) edb93xx arm arm920t edb93xx - ep93xx
+
 #########################################################################
 # ARM supplied Versatile development boards
 #########################################################################
@@ -2705,104 +2159,9 @@ versatilepb_config :	unconfig
 	@board/armltd/versatile/split_by_variant.sh $@
 
 #########################################################################
-## S3C44B0 Systems
-#########################################################################
-
-B2_config	:	unconfig
-	@$(MKCONFIG) $@ arm s3c44b0 $(call ucname,$@) dave
-
-#########################################################################
-## ARM720T Systems
-#########################################################################
-
-# generic boards
-################
-
-armadillo_config	\
-ep7312_config		\
-impa7_config		\
-modnet50_config :	unconfig
-	@$(MKCONFIG) $@ arm arm720t $(call lcname,$@)
-
-evb4510_config :	unconfig
-	@$(MKCONFIG) $@ arm arm720t $(call lcname,$@) NULL s3c4510b
-
-lpc2292sodimm_config:	unconfig
-	@$(MKCONFIG) $@ arm arm720t $(call lcname,$@) NULL lpc2292
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-SMN42_config	:	unconfig
-	@$(MKCONFIG) $@ arm arm720t $(call ucname,$@) siemens lpc2292
-
-#########################################################################
-## ARM CORTEX Systems
-#########################################################################
-omapname = $(shell echo $(1) | sed -e 's/omap[0-9]_//' -e 's/\(.*\)_config/\L\1/')
-
-# generic boards
-################
-
-omap3_overo_config	\
-omap3_pandora_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 $(call omapname,$@) NULL omap3
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-mx51evk_config	: unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 $(call lcname,$@) freescale mx51
-
-omap3_zoom1_config	\
-omap3_zoom2_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 $(call omapname,$@) logicpd omap3
-
-smdkc100_config:	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 $(call lcname,$@) samsung s5pc1xx
-
-omap3_beagle_config	\
-omap3_evm_config	\
-omap3_sdp3430_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 $(call omapname,$@) ti omap3
-
-devkit8000_config :	unconfig
-	@$(MKCONFIG) $@ arm arm_cortexa8 $(call lcname,$@) timll omap3
-
-#########################################################################
 ## XScale Systems
 #########################################################################
 
-# generic boards
-################
-
-actux1_config	\
-actux2_config	\
-actux3_config	\
-actux4_config	\
-ixdp425_config	\
-ixdpg425_config	:	unconfig
-	@$(MKCONFIG) $@ arm ixp $(call lcname,$@)
-
-cerf250_config	\
-cradle_config	\
-csb226_config	\
-delta_config	\
-innokom_config	\
-lubbock_config	\
-pleb2_config	\
-logodl_config	\
-pxa255_idp_config \
-wepep250_config	\
-xaeniax_config	\
-xm250_config	\
-xsengine_config \
-zylonite_config :
-	@$(MKCONFIG) $@ arm pxa $(call lcname,$@)
-
-# special boards
-################
-
 pdnb3_config \
 scpu_config:	unconfig
 	@mkdir -p $(obj)include
@@ -2823,32 +2182,11 @@ trizepsiv_config	:	unconfig
 ## ARM1136 Systems
 #########################################################################
 
-# generic boards
-################
-
-# vendor specific boards (sorted by vendor)
-###########################################
-
-qong_config		: unconfig
-	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) davedenx mx31
-
-mx31ads_config		: unconfig
-	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) freescale mx31
-
-imx31_litekit_config	: unconfig
-	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) logicpd mx31
-
-omap2420h4_config	: unconfig
-	@$(MKCONFIG) $@ arm arm1136 $(call lcname,$@) ti omap24xx
-
-# special boards
-################
-
 apollon_config		: unconfig
 	@mkdir -p $(obj)include
 	@echo "#define CONFIG_ONENAND_U_BOOT" > $(obj)include/config.h
 	@echo "CONFIG_ONENAND_U_BOOT = y" >> $(obj)include/config.mk
-	@$(MKCONFIG) $@ arm arm1136 apollon NULL omap24xx
+	@$(MKCONFIG) $@ arm arm1136 apollon - omap24xx
 
 imx31_phycore_eet_config \
 imx31_phycore_config	: unconfig
@@ -2856,7 +2194,7 @@ imx31_phycore_config	: unconfig
 	@if [ -n "$(findstring _eet_,$@)" ]; then			\
 		echo "#define CONFIG_IMX31_PHYCORE_EET" >> $(obj)include/config.h;	\
 	fi
-	@$(MKCONFIG) -n $@ -a imx31_phycore arm arm1136 imx31_phycore NULL mx31
+	@$(MKCONFIG) -n $@ -a imx31_phycore arm arm1136 imx31_phycore - mx31
 
 mx31pdk_config \
 mx31pdk_nand_config	: unconfig
@@ -2886,38 +2224,12 @@ smdk6400_config	:	unconfig
 	@$(MKCONFIG) $(subst _noUSB,,$(@:_config=)) arm arm1176 smdk6400 samsung s3c64xx
 
 #========================================================================
-# i386
-#========================================================================
-#########################################################################
-## AMD SC520 CDP
-#########################################################################
-
-# generic boards
-################
-eNET_config		\
-sc520_cdp_config	\
-sc520_spunk_config	:	unconfig
-	@$(MKCONFIG) $@ i386 i386 $(call lcname,$@) NULL sc520
-
-sc520_spunk_rel_config	:	unconfig
-	@$(MKCONFIG) $@ i386 i386 sc520_spunk NULL sc520
-
-#========================================================================
 # MIPS
 #========================================================================
 #########################################################################
 ## MIPS32 4Kc
 #########################################################################
 
-# generic boards
-################
-
-tb0229_config: unconfig
-	@$(MKCONFIG) $@ mips mips $(call lcname,$@)
-
-# special boards
-################
-
 incaip_100MHz_config	\
 incaip_133MHz_config	\
 incaip_150MHz_config	\
@@ -3000,13 +2312,6 @@ qemu_mips_config	: unconfig
 	@echo "#define CONFIG_QEMU_MIPS 1" >$(obj)include/config.h
 	@$(MKCONFIG) -a qemu-mips mips mips qemu-mips
 
-#########################################################################
-## MIPS64 5Kc
-#########################################################################
-
-purple_config :		unconfig
-	@$(MKCONFIG) $@ mips mips purple
-
 #========================================================================
 # Nios
 #========================================================================
@@ -3015,18 +2320,6 @@ purple_config :		unconfig
 ## Nios-II
 #########################################################################
 
-# vendor specific boards (sorted by vendor)
-###########################################
-
-EP1C20_config	\
-EP1S10_config	\
-EP1S40_config	: unconfig
-	@$(MKCONFIG) $@ nios2 nios2 $(call lcname,$@) altera
-
-PK1C20_config	\
-PCI5441_config	: unconfig
-	@$(MKCONFIG) $@ nios2 nios2 $(call lcname,$@) psyent
-
 # nios2 generic boards
 NIOS2_GENERIC = nios2-generic
 
@@ -3034,60 +2327,14 @@ $(NIOS2_GENERIC:%=%_config) : unconfig
 	@$(MKCONFIG) $@ nios2 nios2 nios2-generic altera
 
 #========================================================================
-## Microblaze
-#========================================================================
-
-microblaze-generic_config:	unconfig
-	@$(MKCONFIG) $@ microblaze microblaze microblaze-generic xilinx
-
-#========================================================================
 # Blackfin
 #========================================================================
 
-# Analog Devices boards
-BFIN_BOARDS = bf518f-ezbrd bf526-ezbrd bf527-ezkit bf533-ezkit bf533-stamp \
-	bf537-pnav bf537-stamp bf538f-ezkit bf548-ezkit bf561-ezkit
-
-# Bluetechnix tinyboards
-BFIN_BOARDS += cm-bf527 cm-bf533 cm-bf537e cm-bf537u cm-bf548 cm-bf561 \
-	tcm-bf518 tcm-bf537
-
-# Misc third party boards
-BFIN_BOARDS += bf537-minotaur bf537-srv1 bf561-acvilon blackstamp ip04
-
-# I-SYST Micromodule
-BFIN_BOARDS += ibf-dsp561
-
-$(BFIN_BOARDS:%=%_config)	: unconfig
-	@$(MKCONFIG) $@ blackfin blackfin $(@:_config=)
-
 bf527-ezkit-v2_config	: unconfig
 	@$(MKCONFIG) -t BF527_EZKIT_REV_2_1 \
 		bf527-ezkit blackfin blackfin bf527-ezkit
 
 #========================================================================
-# AVR32
-#========================================================================
-
-atngw100_config	:	unconfig
-	@$(MKCONFIG) $@ avr32 at32ap atngw100 atmel at32ap700x
-
-atstk1002_config	\
-atstk1003_config	\
-atstk1004_config	\
-atstk1006_config	:	unconfig
-	@$(MKCONFIG) $@ avr32 at32ap atstk1000 atmel at32ap700x
-
-favr-32-ezkit_config	:	unconfig
-	@$(MKCONFIG) $@ avr32 at32ap favr-32-ezkit earthlcd at32ap700x
-
-hammerhead_config	:	unconfig
-	@$(MKCONFIG) $@ avr32 at32ap hammerhead miromico at32ap700x
-
-mimc200_config		:	unconfig
-	@$(MKCONFIG) $@ avr32 at32ap mimc200 mimc at32ap700x
-
-#========================================================================
 # SH3 (SuperH)
 #========================================================================
 
@@ -3169,28 +2416,6 @@ espt_config  :   unconfig
 	@echo "#define CONFIG_ESPT 1" > $(obj)include/config.h
 	@$(MKCONFIG) -a $@ sh sh4 espt
 
-#========================================================================
-# SPARC
-#========================================================================
-
-#########################################################################
-## LEON2
-#########################################################################
-
-grsim_leon2_config : unconfig
-	@$(MKCONFIG) $@ sparc leon2 $(call lcname,$@) gaisler
-
-#########################################################################
-## LEON3
-#########################################################################
-
-gr_xc3s_1500_config	\
-gr_cpci_ax2000_config	\
-gr_ep2s60_config	\
-grsim_config	:	unconfig
-	@$(MKCONFIG) $@ sparc leon3 $(call lcname,$@) gaisler
-
-#########################################################################
 #########################################################################
 #########################################################################
 
diff --git a/boards.cfg b/boards.cfg
new file mode 100644
index 0000000..e54673e
--- /dev/null
+++ b/boards.cfg
@@ -0,0 +1,356 @@
+#
+# List of boards
+#
+# Syntax:
+#	white-space separated list of entries;
+#	each entry has the following fields:
+#
+#	Targetname  Architecture  CPU  Boardname  Vendor  SoC
+#
+#	Unused fields can be specified as "-", or omitted if they
+#	are the last field on the line.
+#
+#	Lines starting with '#' are comments.
+#	Blank lines are ignored.
+#
+# To keep the list sorted, use something like
+#
+#	:.,$! sort -f -k2,2 -k3,3 -k6,6 -k5,5 -k1,1
+#
+# Target	ARCH	CPU		Board name	Vendor		SoC
+###########################################################################
+
+qong		arm	arm1136		-		davedenx	mx31
+mx31ads		arm	arm1136		-		freescale	mx31
+ep7312		arm	arm720t
+impa7		arm	arm720t
+SMN42		arm	arm720t		-		siemens		lpc2292
+evb4510		arm	arm720t		-		-		s3c4510b
+a320evb		arm	arm920t		-		faraday		a320
+cmc_pu2		arm	arm920t		-		-		at91rm9200
+csb637		arm	arm920t		-		-		at91rm9200
+kb9202		arm	arm920t		-		-		at91rm9200
+m501sk		arm	arm920t		-		-		at91rm9200
+mp2usb		arm	arm920t		-		-		at91rm9200
+mx1ads		arm	arm920t		-		-		imx
+mx1fs2		arm	arm920t		-		-		imx
+scb9328		arm	arm920t		-		-		imx
+cm4008		arm	arm920t		-		-		ks8695
+cm41xx		arm	arm920t		-		-		ks8695
+VCMA9		arm	arm920t		vcma9		mpl		s3c24x0
+netstar		arm	arm925t
+meesc		arm	arm926ejs	-		esd		at91
+otc570		arm	arm926ejs	-		esd		at91
+pm9261		arm	arm926ejs	-		ronetix		at91
+pm9263		arm	arm926ejs	-		ronetix		at91
+suen3		arm	arm926ejs	km_arm		keymile		kirkwood
+rd6281a		arm	arm926ejs	-		Marvell		kirkwood
+mx51evk		arm	arm_cortexa8	mx51evk		freescale	mx51
+actux1		arm	ixp
+actux2		arm	ixp
+actux3		arm	ixp
+actux4		arm	ixp
+ixdp425		arm	ixp
+cerf250		arm	pxa
+cradle		arm	pxa
+csb226		arm	pxa
+delta		arm	pxa
+innokom		arm	pxa
+logodl		arm	pxa
+lubbock		arm	pxa
+pleb2		arm	pxa
+xaeniax		arm	pxa
+xm250		arm	pxa
+B2		arm	s3c44b0		-		dave
+assabet		arm	sa1100
+dnp1110		arm	sa1100
+gcplus		arm	sa1100
+lart		arm	sa1100
+shannon		arm	sa1100
+mimc200		avr32	at32ap		-		mimc		at32ap700x
+eNET		i386	i386		-		-		sc520
+idmr		m68k	mcf52x2
+TASREG		m68k	mcf52x2		tasreg		esd
+M5272C3		m68k	mcf52x2		m5272c3		freescale
+EP2500		m68k	mcf52x2		ep2500		Mercury
+purple		mips	mips
+tb0229		mips	mips
+EP1C20		nios2	nios2		ep1c20		altera
+EP1S10		nios2	nios2		ep1s10		altera
+EP1S40		nios2	nios2		ep1s40		altera
+PCI5441		nios2	nios2		pci5441		psyent
+PK1C20		nios2	nios2		pk1c20		psyent
+P3G4		powerpc	74xx_7xx	evb64260
+ppmc7xx		powerpc	74xx_7xx
+ZUMA		powerpc	74xx_7xx	evb64260
+BAB7xx		powerpc	74xx_7xx 	bab7xx		eltec
+ELPPC		powerpc	74xx_7xx 	elppc		eltec
+CPCI750		powerpc	74xx_7xx 	cpci750		esd
+DB64360		powerpc	74xx_7xx 	db64360		Marvell
+DB64460		powerpc	74xx_7xx 	db64460		Marvell
+aria		powerpc	mpc512x		-		davedenx
+PATI		powerpc	mpc5xx		pati		mpl
+BC3450		powerpc	mpc5xxx		bc3450
+canmb		powerpc	mpc5xxx
+cm5200		powerpc	mpc5xxx
+hmi1001		powerpc	mpc5xxx
+inka4x0		powerpc	mpc5xxx
+ipek01		powerpc	mpc5xxx
+jupiter		powerpc	mpc5xxx
+mucmc52		powerpc	mpc5xxx
+munices		powerpc	mpc5xxx
+o2dnt		powerpc	mpc5xxx
+uc101		powerpc	mpc5xxx
+v38b		powerpc	mpc5xxx
+pf5200		powerpc	mpc5xxx		-		esd
+aev		powerpc	mpc5xxx		tqm5200		tqc
+smmaco4		powerpc	mpc5xxx		tqm5200		tqc
+spieval		powerpc	mpc5xxx		tqm5200		tqc
+sorcery		powerpc	mpc8220
+A3000		powerpc	mpc824x		a3000
+barco		powerpc	mpc824x
+BMW		powerpc	mpc824x		bmw
+CU824		powerpc	mpc824x		cu824
+MOUSSE		powerpc	mpc824x		mousse
+MUSENKI		powerpc	mpc824x		musenki
+MVBLUE		powerpc	mpc824x		mvblue
+OXC		powerpc	mpc824x		oxc
+PN62		powerpc	mpc824x		pn62
+sbc8240		powerpc	mpc824x
+utx8245		powerpc	mpc824x
+debris		powerpc	mpc824x		-		etin
+kvme080		powerpc	mpc824x		-		etin
+atc		powerpc	mpc8260
+ep8260		powerpc	mpc8260
+ep82xxm		powerpc	mpc8260
+gw8260		powerpc	mpc8260
+hymod		powerpc	mpc8260
+IDS8247		powerpc	mpc8260		ids8247
+sacsng		powerpc	mpc8260
+sbc8260		powerpc	mpc8260
+ZPC1900		powerpc	mpc8260		zpc1900
+mgcoge		powerpc	mpc8260		-		keymile
+SCM		powerpc	mpc8260		-		siemens
+TQM8272		powerpc	mpc8260		tqm8272		tqc
+kmeter1		powerpc	mpc83xx		kmeter1		keymile
+MVBLM7		powerpc	mpc83xx		mvblm7		matrix_vision
+TQM834x		powerpc	mpc83xx		tqm834x		tqc
+PM854		powerpc	mpc85xx		pm854
+PM856		powerpc	mpc85xx		pm856
+stxgp3		powerpc	mpc85xx		stxgp3		stx
+c2mon		powerpc	mpc8xx
+EP88x		powerpc	mpc8xx		ep88x
+ETX094		powerpc	mpc8xx		etx094
+FLAGADM		powerpc	mpc8xx		flagadm
+GENIETV		powerpc	mpc8xx		genietv
+GTH		powerpc	mpc8xx		gth
+hermes		powerpc	mpc8xx
+IP860		powerpc	mpc8xx		ip860
+LANTEC		powerpc	mpc8xx		lantec
+lwmon		powerpc	mpc8xx
+NX823		powerpc	mpc8xx		nx823
+quantum		powerpc	mpc8xx
+R360MPI		powerpc	mpc8xx		r360mpi
+RBC823		powerpc	mpc8xx		rbc823
+rmu		powerpc	mpc8xx
+RPXlite		powerpc	mpc8xx
+spc1920		powerpc	mpc8xx
+uc100		powerpc	mpc8xx
+MHPC		powerpc	mpc8xx		mhpc		eltec
+TOP860		powerpc	mpc8xx		top860		emk
+kmsupx4		powerpc	mpc8xx		km8xx		keymile
+mgsuvd		powerpc	mpc8xx		km8xx		keymile
+KUP4K		powerpc	mpc8xx		kup4k		kup
+KUP4X		powerpc	mpc8xx		kup4k		kup
+ELPT860		powerpc	mpc8xx		elpt860		LEOX
+CCM		powerpc	mpc8xx		-		siemens
+IAD210		powerpc	mpc8xx		-		siemens
+pcu_e		powerpc	mpc8xx		-		siemens
+QS823		powerpc	mpc8xx		qs850		snmc
+QS850		powerpc	mpc8xx		qs850		snmc
+QS860T		powerpc	mpc8xx		qs860t		snmc
+stxxtc		powerpc	mpc8xx		stxxtc		stx
+HMI10		powerpc	mpc8xx		tqm8xx		tqc
+SM850		powerpc	mpc8xx		tqm8xx		tqc
+AMX860		powerpc	mpc8xx		amx860		westel
+csb272		powerpc	ppc4xx
+csb472		powerpc	ppc4xx
+ERIC		powerpc	ppc4xx		eric
+G2000		powerpc	ppc4xx		g2000
+JSE		powerpc	ppc4xx		jse
+korat		powerpc	ppc4xx
+lwmon5		powerpc	ppc4xx
+ML2		powerpc	ppc4xx
+sbc405		powerpc	ppc4xx
+sc3		powerpc	ppc4xx
+zeus		powerpc	ppc4xx
+acadia		powerpc	ppc4xx		-		amcc
+bamboo		powerpc	ppc4xx		-		amcc
+bubinga		powerpc	ppc4xx		-		amcc
+ebony		powerpc	ppc4xx		-		amcc
+katmai		powerpc	ppc4xx		-		amcc
+luan		powerpc	ppc4xx		-		amcc
+makalu		powerpc	ppc4xx		-		amcc
+ocotea		powerpc	ppc4xx		-		amcc
+redwood		powerpc	ppc4xx		-		amcc
+taihu		powerpc	ppc4xx		-		amcc
+taishan		powerpc	ppc4xx		-		amcc
+yucca		powerpc	ppc4xx		-		amcc
+AP1000		powerpc	ppc4xx		ap1000		amirix
+CRAYL1		powerpc	ppc4xx		L1		cray
+ADCIOP		powerpc	ppc4xx		adciop		esd
+APC405		powerpc	ppc4xx		apc405		esd
+AR405		powerpc	ppc4xx		ar405		esd
+ASH405		powerpc	ppc4xx		ash405		esd
+CANBT		powerpc	ppc4xx		canbt		esd
+CMS700		powerpc	ppc4xx		cms700		esd
+CPCI2DP		powerpc	ppc4xx		cpci2dp		esd
+DP405		powerpc	ppc4xx		dp405		esd
+DU405		powerpc	ppc4xx		du405		esd
+DU440		powerpc	ppc4xx		du440		esd
+HH405		powerpc	ppc4xx		hh405		esd
+HUB405		powerpc	ppc4xx		hub405		esd
+PCI405		powerpc	ppc4xx		pci405		esd
+PLU405		powerpc	ppc4xx		plu405		esd
+PMC405		powerpc	ppc4xx		pmc405		esd
+PMC440		powerpc	ppc4xx		pmc440		esd
+VOH405		powerpc	ppc4xx		voh405		esd
+VOM405		powerpc	ppc4xx		vom405		esd
+WUH405		powerpc	ppc4xx		wuh405		esd
+neo		powerpc	ppc4xx		-		gdsys
+icon		powerpc	ppc4xx		-		mosaixtech
+MIP405		powerpc	ppc4xx		mip405		mpl
+PIP405		powerpc	ppc4xx		pip405		mpl
+alpr		powerpc	ppc4xx		-		prodrive
+p3p440		powerpc	ppc4xx		-		prodrive
+KAREF		powerpc	ppc4xx		karef		sandburst
+grsim		sparc	leon3		-		gaisler
+imx31_litekit	arm	arm1136		-		logicpd		mx31
+omap2420h4	arm	arm1136		-		ti		omap24xx
+armadillo	arm	arm720t
+modnet50	arm	arm720t
+lpc2292sodimm	arm	arm720t		-		-		lpc2292
+eb_cpux9k2	arm	arm920t		-		BuS		at91
+at91rm9200dk	arm	arm920t		-		atmel		at91rm9200
+at91rm9200ek	arm	arm920t		-		atmel		at91rm9200
+sbc2410x	arm	arm920t		-		-		s3c24x0
+smdk2400	arm	arm920t		-		samsung		s3c24x0
+smdk2410	arm	arm920t		-		samsung		s3c24x0
+voiceblue	arm	arm925t
+omap1510inn	arm	arm925t		-		ti
+at91cap9adk	arm	arm926ejs	-		atmel		at91
+afeb9260	arm	arm926ejs	-		-		at91
+guruplug	arm	arm926ejs	-		Marvell		kirkwood
+mv88f6281gtw_ge	arm	arm926ejs	-		Marvell		kirkwood
+openrd_base	arm	arm926ejs	-		Marvell		kirkwood
+sheevaplug	arm	arm926ejs	-		Marvell		kirkwood
+imx27lite	arm	arm926ejs	imx27lite	logicpd		mx27
+magnesium	arm	arm926ejs	imx27lite	logicpd		mx27
+omap5912osk	arm	arm926ejs	-		ti		omap
+omap3_zoom1	arm	arm_cortexa8	zoom1		logicpd		omap3
+omap3_zoom2	arm	arm_cortexa8	zoom2		logicpd		omap3
+omap3_overo	arm	arm_cortexa8	overo		-		omap3
+omap3_pandora	arm	arm_cortexa8	pandora		-		omap3
+omap3_beagle	arm	arm_cortexa8	beagle		ti		omap3
+omap3_evm	arm	arm_cortexa8	evm		ti		omap3
+omap3_sdp3430	arm	arm_cortexa8	sdp3430		ti		omap3
+devkit8000	arm	arm_cortexa8	devkit8000	timll		omap3
+smdkc100	arm	arm_cortexa8	smdkc100	samsung		s5pc1xx
+ixdpg425	arm	ixp
+lpd7a400	arm	lh7a40x		lpd7a40x
+lpd7a404	arm	lh7a40x		lpd7a40x
+pxa255_idp	arm	pxa
+wepep250	arm	pxa
+xsengine	arm	pxa
+zylonite	arm	pxa
+atngw100	avr32	at32ap		-		atmel		at32ap700x
+atstk1002	avr32	at32ap		atstk1000	atmel		at32ap700x
+atstk1003	avr32	at32ap		atstk1000	atmel		at32ap700x
+atstk1004	avr32	at32ap		atstk1000	atmel		at32ap700x
+atstk1006	avr32	at32ap		atstk1000	atmel		at32ap700x
+favr-32-ezkit	avr32	at32ap		-		earthlcd	at32ap700x
+hammerhead	avr32	at32ap		-		miromico	at32ap700x
+bf518f-ezbrd	blackfin	blackfin
+bf526-ezbrd	blackfin	blackfin
+bf527-ezkit	blackfin	blackfin
+bf533-ezkit	blackfin	blackfin
+bf533-stamp	blackfin	blackfin
+bf537-minotaur	blackfin	blackfin
+bf537-pnav	blackfin	blackfin
+bf537-srv1	blackfin	blackfin
+bf537-stamp	blackfin	blackfin
+bf538f-ezkit	blackfin	blackfin
+bf548-ezkit	blackfin	blackfin
+bf561-acvilon	blackfin	blackfin
+bf561-ezkit	blackfin	blackfin
+blackstamp	blackfin	blackfin
+cm-bf527	blackfin	blackfin
+cm-bf533	blackfin	blackfin
+cm-bf537e	blackfin	blackfin
+cm-bf537u	blackfin	blackfin
+cm-bf548	blackfin	blackfin
+cm-bf561	blackfin	blackfin
+ibf-dsp561	blackfin	blackfin
+ip04	blackfin	blackfin
+tcm-bf518	blackfin	blackfin
+tcm-bf537	blackfin	blackfin
+sc520_cdp	i386	i386		-		-		sc520
+sc520_spunk	i386	i386		-		-		sc520
+sc520_spunk_rel	i386	i386		sc520_spunk_rel	-		sc520
+M5208EVBE	m68k	mcf52x2		m5208evbe	freescale
+M5249EVB	m68k	mcf52x2		m5249evb	freescale
+M5253DEMO	m68k	mcf52x2		m5253demo	freescale
+M5253EVBE	m68k	mcf52x2		m5253evbe	freescale
+M5271EVB	m68k	mcf52x2		m5271evb	freescale
+M5275EVB	m68k	mcf52x2		m5275evb	freescale
+M5282EVB	m68k	mcf52x2		m5282evb	freescale
+M53017EVB	m68k	mcf52x2		m53017evb	freescale
+microblaze-generic	microblaze	microblaze	microblaze-generic	xilinx
+mpc7448hpc2	powerpc	74xx_7xx 	mpc7448hpc2	freescale
+AmigaOneG3SE	powerpc	74xx_7xx 	AmigaOneG3SE	MAI
+pdm360ng	powerpc	mpc512x
+mecp5123	powerpc	mpc512x		-		esd
+cmi_mpc5xx	powerpc	mpc5xx		cmi
+motionpro	powerpc	mpc5xxx
+cpci5200	powerpc	mpc5xxx		-		esd
+mecp5200	powerpc	mpc5xxx		-		esd
+Alaska8220	powerpc	mpc8220		alaska
+Yukon8220	powerpc	mpc8220		alaska
+HIDDEN_DRAGON	powerpc	mpc824x		hidden_dragon
+IPHASE4539	powerpc	mpc8260		iphase4539
+ppmc8260	powerpc	mpc8260
+RPXsuper	powerpc	mpc8260		rpxsuper
+rsdproto	powerpc	mpc8260
+MPC8266ADS	powerpc	mpc8260		mpc8266ads	freescale
+MPC8323ERDB	powerpc	mpc83xx		mpc8323erdb	freescale
+MPC8349EMDS	powerpc	mpc83xx		mpc8349emds	freescale
+MPC837XERDB	powerpc	mpc83xx		mpc837xerdb	freescale
+ATUM8548	powerpc	mpc85xx		atum8548
+socrates	powerpc	mpc85xx		socrates
+MPC8540ADS	powerpc	mpc85xx		mpc8540ads	freescale
+MPC8544DS	powerpc	mpc85xx		mpc8544ds	freescale
+MPC8560ADS	powerpc	mpc85xx		mpc8560ads	freescale
+MPC8568MDS	powerpc	mpc85xx		mpc8568mds	freescale
+XPEDITE5200	powerpc	mpc85xx		xpedite5200	xes
+XPEDITE5370	powerpc	mpc85xx		xpedite5370	xes
+sbc8641d	powerpc	mpc86xx
+MPC8610HPCD	powerpc	mpc86xx		mpc8610hpcd	freescale
+XPEDITE5170	powerpc	mpc86xx		xpedite5170	xes
+cogent_mpc8xx	powerpc	mpc8xx		cogent
+ESTEEM192E	powerpc	mpc8xx		esteem192e
+RPXClassic	powerpc	mpc8xx
+RRvision	powerpc	mpc8xx
+svm_sc8xx	powerpc	mpc8xx
+pcs440ep	powerpc	ppc4xx
+quad100hd	powerpc	ppc4xx
+dlvision	powerpc	ppc4xx		-		gdsys
+gdppc440etx	powerpc	ppc4xx		-		gdsys
+CPCIISER4	powerpc	ppc4xx		cpciiser4	esd
+DASA_SIM	powerpc	ppc4xx		dasa_sim	esd
+PMC405DE	powerpc	ppc4xx		pmc405de	esd
+METROBOX	powerpc	ppc4xx		metrobox	sandburst
+XPEDITE1000	powerpc	ppc4xx		xpedite1000	xes
+grsim_leon2	sparc	leon2		-		gaisler
+gr_cpci_ax2000	sparc	leon3		-		gaisler
+gr_ep2s60	sparc	leon3		-		gaisler
+gr_xc3s_1500	sparc	leon3		-		gaisler
diff --git a/mkconfig b/mkconfig
index a71d09e..b661071 100755
--- a/mkconfig
+++ b/mkconfig
@@ -12,6 +12,24 @@ APPEND=no	# Default: Create new config file
 BOARD_NAME=""	# Name to print in make output
 TARGETS=""
 
+arch=""
+cpu=""
+board=""
+vendor=""
+soc=""
+
+if [ \( $# -eq 2 \) -a \( "$1" = "-A" \) ] ; then
+	# Automatic mode
+	line=`egrep -i "^[[:space:]]*${2}[[:space:]]" boards.cfg` || {
+		echo "make: *** No rule to make target \`$2_config'.  Stop." >&2
+		exit 1
+	}
+
+	set ${line}
+	# add default board name if needed
+	[ $# = 3 ] && set ${line} ${1}
+fi
+
 while [ $# -gt 0 ] ; do
 	case "$1" in
 	--) shift ; break ;;
@@ -22,13 +40,25 @@ while [ $# -gt 0 ] ; do
 	esac
 done
 
-[ "${BOARD_NAME}" ] || BOARD_NAME="${1%_config}"
-
 [ $# -lt 4 ] && exit 1
 [ $# -gt 6 ] && exit 1
 
-if [ "${ARCH}" -a "${ARCH}" != "$2" ]; then
-	echo "Failed: \$ARCH=${ARCH}, should be '$2' for ${BOARD_NAME}" 1>&2
+CONFIG_NAME="${1%_config}"
+
+[ "${BOARD_NAME}" ] || BOARD_NAME="${CONFIG_NAME}"
+
+arch="$2"
+cpu="$3"
+if [ "$4" = "-" ] ; then
+	board=${BOARD_NAME}
+else
+	board="$4"
+fi
+[ $# -gt 4 ] && [ "$5" != "-" ] && vendor="$5"
+[ $# -gt 5 ] && [ "$6" != "-" ] && soc="$6"
+
+if [ "${ARCH}" -a "${ARCH}" != "${arch}" ]; then
+	echo "Failed: \$ARCH=${ARCH}, should be '${arch}' for ${BOARD_NAME}" 1>&2
 	exit 1
 fi
 
@@ -42,26 +72,26 @@ if [ "$SRCTREE" != "$OBJTREE" ] ; then
 	mkdir -p ${OBJTREE}/include2
 	cd ${OBJTREE}/include2
 	rm -f asm
-	ln -s ${SRCTREE}/arch/$2/include/asm asm
-	LNPREFIX=${SRCTREE}/arch/$2/include/asm/
+	ln -s ${SRCTREE}/arch/${arch}/include/asm asm
+	LNPREFIX=${SRCTREE}/arch/${arch}/include/asm/
 	cd ../include
 	rm -f asm
-	ln -s ${SRCTREE}/arch/$2/include/asm asm
+	ln -s ${SRCTREE}/arch/${arch}/include/asm asm
 else
 	cd ./include
 	rm -f asm
-	ln -s ../arch/$2/include/asm asm
+	ln -s ../arch/${arch}/include/asm asm
 fi
 
 rm -f asm/arch
 
-if [ -z "$6" -o "$6" = "NULL" ] ; then
-	ln -s ${LNPREFIX}arch-$3 asm/arch
+if [ -z "${soc}" ] ; then
+	ln -s ${LNPREFIX}arch-${cpu} asm/arch
 else
-	ln -s ${LNPREFIX}arch-$6 asm/arch
+	ln -s ${LNPREFIX}arch-${soc} asm/arch
 fi
 
-if [ "$2" = "arm" ] ; then
+if [ "${arch}" = "arm" ] ; then
 	rm -f asm/proc
 	ln -s ${LNPREFIX}proc-armv asm/proc
 fi
@@ -69,19 +99,19 @@ fi
 #
 # Create include file for Make
 #
-echo "ARCH   = $2" >  config.mk
-echo "CPU    = $3" >> config.mk
-echo "BOARD  = $4" >> config.mk
+echo "ARCH   = ${arch}"  >  config.mk
+echo "CPU    = ${cpu}"   >> config.mk
+echo "BOARD  = ${board}" >> config.mk
 
-[ "$5" ] && [ "$5" != "NULL" ] && echo "VENDOR = $5" >> config.mk
+[ "${vendor}" ] && echo "VENDOR = ${vendor}" >> config.mk
 
-[ "$6" ] && [ "$6" != "NULL" ] && echo "SOC    = $6" >> config.mk
+[ "${soc}"    ] && echo "SOC    = ${soc}"    >> config.mk
 
 # Assign board directory to BOARDIR variable
-if [ -z "$5" -o "$5" = "NULL" ] ; then
-    BOARDDIR=$4
+if [ -z "${vendor}" ] ; then
+    BOARDDIR=${board}
 else
-    BOARDDIR=$5/$4
+    BOARDDIR=${vendor}/${board}
 fi
 
 #
@@ -102,7 +132,7 @@ done
 cat << EOF >> config.h
 #define CONFIG_BOARDDIR board/$BOARDDIR
 #include <config_defaults.h>
-#include <configs/${BOARDNAME}.h>
+#include <configs/${CONFIG_NAME}.h>
 #include <asm/config.h>
 EOF
 
-- 
cgit v1.1


From 105438200744ca81199606a7b62c9eb07ac6efbd Mon Sep 17 00:00:00 2001
From: Anatolij Gustschin <agust@denx.de>
Date: Sat, 1 May 2010 22:21:09 +0200
Subject: video: cfb_console: add weak default video_set_lut()

Do not enforce drivers to provide empty video_set_lut()
if they do not implement indexed color (8 bpp) frame
buffer support. Add default function to the cfb_console
driver and remove empty video_set_lut() functions.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
 arch/powerpc/cpu/mpc512x/diu.c                | 14 --------------
 board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c |  9 ---------
 drivers/video/cfb_console.c                   | 12 ++++++++++++
 drivers/video/sm501.c                         | 13 -------------
 4 files changed, 12 insertions(+), 36 deletions(-)

diff --git a/arch/powerpc/cpu/mpc512x/diu.c b/arch/powerpc/cpu/mpc512x/diu.c
index f8d19a0..1cce6a2 100644
--- a/arch/powerpc/cpu/mpc512x/diu.c
+++ b/arch/powerpc/cpu/mpc512x/diu.c
@@ -179,18 +179,4 @@ void *video_hw_init(void)
 	return (void *)pGD;
 }
 
-/**
-  * Set the LUT
-  *
-  * @index: color number
-  * @r: red
-  * @b: blue
-  * @g: green
-  */
-void video_set_lut
-	(unsigned int index, unsigned char r, unsigned char g, unsigned char b)
-{
-	return;
-}
-
 #endif /* defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE) */
diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c b/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c
index 94fb1eb..a7b7f45 100644
--- a/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c
+++ b/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c
@@ -183,15 +183,6 @@ void *video_hw_init(void)
 	return (void *)pGD;
 }
 
-void video_set_lut (unsigned int index,	/* color number */
-		    unsigned char r,	/* red */
-		    unsigned char g,	/* green */
-		    unsigned char b	/* blue */
-		    )
-{
-	return;
-}
-
 #endif /* defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE) */
 
 #endif /* CONFIG_FSL_DIU_FB */
diff --git a/drivers/video/cfb_console.c b/drivers/video/cfb_console.c
index d1f47c9..96d52fb 100644
--- a/drivers/video/cfb_console.c
+++ b/drivers/video/cfb_console.c
@@ -749,6 +749,18 @@ void video_puts (const char *s)
 
 /*****************************************************************************/
 
+/*
+ * Do not enforce drivers (or board code) to provide empty
+ * video_set_lut() if they do not support 8 bpp format.
+ * Implement weak default function instead.
+ */
+void __video_set_lut (unsigned int index, unsigned char r,
+		      unsigned char g, unsigned char b)
+{
+}
+void video_set_lut (unsigned int, unsigned char, unsigned char, unsigned char)
+			__attribute__((weak, alias("__video_set_lut")));
+
 #if defined(CONFIG_CMD_BMP) || defined(CONFIG_SPLASH_SCREEN)
 
 #define FILL_8BIT_332RGB(r,g,b)	{			\
diff --git a/drivers/video/sm501.c b/drivers/video/sm501.c
index 283d2d9..8c96316 100644
--- a/drivers/video/sm501.c
+++ b/drivers/video/sm501.c
@@ -131,16 +131,3 @@ void *video_hw_init (void)
 
 	return (&sm501);
 }
-
-/*-----------------------------------------------------------------------------
- * video_set_lut --
- *-----------------------------------------------------------------------------
- */
-void video_set_lut (
-	unsigned int index,           /* color number */
-	unsigned char r,              /* red */
-	unsigned char g,              /* green */
-	unsigned char b               /* blue */
-	)
-{
-}
-- 
cgit v1.1


From e2bee9e3c0f4bd363207ce5e496cef2134f67d28 Mon Sep 17 00:00:00 2001
From: Anatolij Gustschin <agust@denx.de>
Date: Wed, 26 May 2010 10:38:57 +0200
Subject: video: sm501: add support for SM501 chips on PCI bus

Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
 drivers/video/sm501.c | 89 ++++++++++++++++++++++++++++++++++++++++++++++++---
 include/pci_ids.h     |  1 +
 2 files changed, 85 insertions(+), 5 deletions(-)

diff --git a/drivers/video/sm501.c b/drivers/video/sm501.c
index 8c96316..f55bf3c 100644
--- a/drivers/video/sm501.c
+++ b/drivers/video/sm501.c
@@ -31,6 +31,7 @@
 
 #include <common.h>
 
+#include <asm/io.h>
 #include <video_fb.h>
 #include <sm501.h>
 
@@ -54,6 +55,18 @@
 
 GraphicDevice sm501;
 
+void write_be32(int off, unsigned int val)
+{
+	out_be32((unsigned __iomem *)(sm501.isaBase + off), val);
+}
+
+void write_le32(int off, unsigned int val)
+{
+	out_le32((unsigned __iomem *)(sm501.isaBase + off), val);
+}
+
+void (*write_reg32)(int off, unsigned int val) = write_be32;
+
 /*-----------------------------------------------------------------------------
  * SmiSetRegs --
  *-----------------------------------------------------------------------------
@@ -66,7 +79,7 @@ static void SmiSetRegs (void)
 	 */
 	const SMI_REGS *preg = board_get_regs ();
 	while (preg->Index) {
-		write32 (preg->Index, preg->Value);
+		write_reg32 (preg->Index, preg->Value);
 		/*
 		 * Insert a delay between
 		 */
@@ -75,26 +88,92 @@ static void SmiSetRegs (void)
 	}
 }
 
+#ifdef CONFIG_VIDEO_SM501_PCI
+static struct pci_device_id sm501_pci_tbl[] = {
+	{ PCI_VENDOR_ID_SMI, PCI_DEVICE_ID_SMI_501 },
+	{}
+};
+#endif
+
 /*-----------------------------------------------------------------------------
  * video_hw_init --
  *-----------------------------------------------------------------------------
  */
 void *video_hw_init (void)
 {
+#ifdef CONFIG_VIDEO_SM501_PCI
+	unsigned int pci_mem_base, pci_mmio_base;
+	unsigned int id;
+	unsigned short device_id;
+	pci_dev_t devbusfn;
+	int mem;
+#endif
 	unsigned int *vm, i;
 
 	memset (&sm501, 0, sizeof (GraphicDevice));
 
+#ifdef CONFIG_VIDEO_SM501_PCI
+	printf("Video: ");
+
+	/* Look for SM501/SM502 chips */
+	devbusfn = pci_find_devices(sm501_pci_tbl, 0);
+	if (devbusfn < 0) {
+		printf ("PCI Controller not found.\n");
+		goto not_pci;
+	}
+
+	/* Setup */
+	pci_write_config_dword (devbusfn, PCI_COMMAND,
+				(PCI_COMMAND_MEMORY | PCI_COMMAND_IO));
+	pci_read_config_word (devbusfn, PCI_DEVICE_ID, &device_id);
+	pci_read_config_dword (devbusfn, PCI_REVISION_ID, &id);
+	pci_read_config_dword (devbusfn, PCI_BASE_ADDRESS_0, &pci_mem_base);
+	pci_read_config_dword (devbusfn, PCI_BASE_ADDRESS_1, &pci_mmio_base);
+	sm501.frameAdrs = pci_mem_to_phys (devbusfn, pci_mem_base);
+	sm501.isaBase = pci_mem_to_phys (devbusfn, pci_mmio_base);
+
+	if (sm501.isaBase)
+		write_reg32 = write_le32;
+
+	mem = in_le32 ((unsigned __iomem *)(sm501.isaBase + 0x10));
+	mem = (mem & 0x0000e000) >> 13;
+	switch (mem) {
+	case 1:
+		mem = 8;
+		break;
+	case 2:
+		mem = 16;
+		break;
+	case 3:
+		mem = 32;
+		break;
+	case 4:
+		mem = 64;
+		break;
+	case 5:
+		mem = 2;
+		break;
+	case 0:
+	default:
+		mem = 4;
+	}
+	printf ("PCI SM50%d %d MB\n", ((id & 0xff) == 0xC0) ? 2 : 1, mem);
+not_pci:
+#endif
 	/*
 	 * Initialization of the access to the graphic chipset Retreive base
 	 * address of the chipset (see board/RPXClassic/eccx.c)
 	 */
-	if ((sm501.isaBase = board_video_init ()) == 0) {
-		return (NULL);
+	if (!sm501.isaBase) {
+		sm501.isaBase = board_video_init ();
+		if (!sm501.isaBase)
+			return NULL;
 	}
 
-	if ((sm501.frameAdrs = board_video_get_fb ()) == 0) {
-		return (NULL);
+	if (!sm501.frameAdrs) {
+		sm501.frameAdrs = board_video_get_fb ();
+		if (!sm501.frameAdrs)
+			return NULL;
 	}
 
 	sm501.winSizeX = board_get_width ();
diff --git a/include/pci_ids.h b/include/pci_ids.h
index edfdc1e..dcc381d 100644
--- a/include/pci_ids.h
+++ b/include/pci_ids.h
@@ -1454,6 +1454,7 @@
 #define PCI_DEVICE_ID_SMI_710		0x0710
 #define PCI_DEVICE_ID_SMI_712		0x0712
 #define PCI_DEVICE_ID_SMI_810		0x0810
+#define PCI_DEVICE_ID_SMI_501		0x0501
 
 #define PCI_VENDOR_ID_HUGHES		0x1273
 #define PCI_DEVICE_ID_HUGHES_DIRECPC	0x0002
-- 
cgit v1.1


From f0a921518b7a016f0a9141933b0d766306394eff Mon Sep 17 00:00:00 2001
From: Anatolij Gustschin <agust@denx.de>
Date: Wed, 26 May 2010 10:38:58 +0200
Subject: video: sm501.c: add weak default functions

For boards using sm501/sm502 on PCI bus some driver
functions normaly defined in the board code are not
needed and empty. Provide weak default functions for
them and do not enforce board code to define empty
functions.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
 drivers/video/sm501.c | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/drivers/video/sm501.c b/drivers/video/sm501.c
index f55bf3c..6a1e010 100644
--- a/drivers/video/sm501.c
+++ b/drivers/video/sm501.c
@@ -95,6 +95,34 @@ static struct pci_device_id sm501_pci_tbl[] = {
 };
 #endif
 
+/*
+ * We do not enforce board code to provide empty/unused
+ * functions for this driver and define weak default
+ * functions here.
+ */
+unsigned int __board_video_init (void)
+{
+	return 0;
+}
+
+unsigned int board_video_init (void)
+			__attribute__((weak, alias("__board_video_init")));
+
+unsigned int __board_video_get_fb (void)
+{
+	return 0;
+}
+
+unsigned int board_video_get_fb (void)
+			__attribute__((weak, alias("__board_video_get_fb")));
+
+void __board_validate_screen (unsigned int base)
+{
+}
+
+void board_validate_screen (unsigned int base)
+			__attribute__((weak, alias("__board_validate_screen")));
+
 /*-----------------------------------------------------------------------------
  * video_hw_init --
  *-----------------------------------------------------------------------------
-- 
cgit v1.1


From 86caca1cd97ba71b7a7c82f2b0163682df35ce5d Mon Sep 17 00:00:00 2001
From: Anatolij Gustschin <agust@denx.de>
Date: Wed, 26 May 2010 10:38:59 +0200
Subject: ppc4xx: icon: add support for SM502 chip

Adds initialization code for SM502 graphics controller
and NL6448BC20-21D LCD panel.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
---
 board/mosaixtech/icon/icon.c | 69 ++++++++++++++++++++++++++++++++++++++++++++
 include/configs/icon.h       | 23 +++++++++++++++
 2 files changed, 92 insertions(+)

diff --git a/board/mosaixtech/icon/icon.c b/board/mosaixtech/icon/icon.c
index fbace9e..ecea1ee 100644
--- a/board/mosaixtech/icon/icon.c
+++ b/board/mosaixtech/icon/icon.c
@@ -317,3 +317,72 @@ int board_pcie_last(void)
 	/* Only 2 PCIe ports used on ICON, so the last one is 1 */
 	return 1;
 }
+
+/*
+ * Video
+ */
+#ifdef CONFIG_VIDEO_SM501
+#include <sm501.h>
+
+#define DISPLAY_WIDTH   640
+#define DISPLAY_HEIGHT  480
+
+static const SMI_REGS sm502_init_regs[] = {
+	{0x00004, 0x0},
+	{0x00040, 0x00021847},
+	{0x00044, 0x091a0a01}, /* 24 MHz pixclk */
+	{0x00054, 0x0},
+	{0x00048, 0x00021847},
+	{0x0004C, 0x091a0a01},
+	{0x00054, 0x1},
+	{0x80004, 0xc428bb17},
+	{0x8000C, 0x00000000},
+	{0x80010, 0x0a000a00},
+	{0x80014, 0x02800000},
+	{0x80018, 0x01e00000},
+	{0x8001C, 0x00000000},
+	{0x80020, 0x01e00280},
+	{0x80024, 0x02fa027f},
+	{0x80028, 0x004a0280},
+	{0x8002C, 0x020c01df},
+	{0x80030, 0x000201e7},
+	{0x80200, 0x00010000},
+	{0x00008, 0x20000000}, /* gpio29 is pwm0, LED_PWM */
+	{0x0000C, 0x3f000000}, /* gpio56 - gpio61 as flat panel data pins */
+	{0x10020, 0x25725728}, /* 20 kHz pwm0, 50 % duty cycle, disabled */
+	{0x80000, 0x0f010106}, /* vsync & hsync pos, disp on */
+	{0, 0}
+};
+
+/*
+ * Return a pointer to the register initialization table.
+ */
+const SMI_REGS *board_get_regs(void)
+{
+	return sm502_init_regs;
+}
+
+int board_get_width(void)
+{
+	return DISPLAY_WIDTH;
+}
+
+int board_get_height(void)
+{
+	return DISPLAY_HEIGHT;
+}
+
+#ifdef CONFIG_CONSOLE_EXTRA_INFO
+/*
+ * Return text to be printed besides the logo.
+ */
+void video_get_info_str(int line_number, char *info)
+{
+	if (line_number == 1)
+		strcpy(info, " Board: ICON");
+	else
+		info[0] = '\0';
+}
+#endif
+
+#endif /* CONFIG_VIDEO_SM501 */
diff --git a/include/configs/icon.h b/include/configs/icon.h
index 3a57d69..7a4e60c 100644
--- a/include/configs/icon.h
+++ b/include/configs/icon.h
@@ -143,6 +143,26 @@
 #define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux	*/
 
 /*
+ * Video options
+ */
+#define CONFIG_VIDEO
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_VIDEO_SM501
+#define CONFIG_VIDEO_SM501_32BPP
+#define CONFIG_VIDEO_SM501_PCI
+#define VIDEO_FB_LITTLE_ENDIAN
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CFG_CONSOLE_IS_IN_ENV
+#endif
+
+/*
  * Environment
  */
 #define	CONFIG_ENV_IS_IN_FLASH	1	/* Environment uses flash	*/
@@ -171,6 +191,9 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
+#ifdef CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#endif
 
 #define	CONFIG_IBM_EMAC4_V4		/* 440SPe has this EMAC version	*/
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
-- 
cgit v1.1


From e6441c4f4070aac6825f5b195f38dfe1da53675c Mon Sep 17 00:00:00 2001
From: Prakash PM <prakash.pm@ti.com>
Date: Tue, 22 Jun 2010 10:24:43 -0400
Subject: DaVinci: EMAC: Get EMAC_MDIO_PHY_NUM from config files

Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
Because of this, EMAC does not work on EVMs which do not have phy
connected at 1. Moving the macro to board config file makes this
configurable depending on where the phy is connected on the MDIO bus.

This patch fixes the board reset issue observed during network access
on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
but it is 0 on DM365EVM.

This patch is verified on da830/omap-l137, dm365 and dm644x evms.

Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
---
 arch/arm/include/asm/arch-davinci/emac_defs.h | 2 +-
 include/configs/da830evm.h                    | 1 +
 include/configs/davinci_dm365evm.h            | 1 +
 include/configs/davinci_dvevm.h               | 1 +
 include/configs/davinci_schmoogie.h           | 1 +
 include/configs/davinci_sffsdr.h              | 1 +
 include/configs/davinci_sonata.h              | 1 +
 7 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/arm/include/asm/arch-davinci/emac_defs.h b/arch/arm/include/asm/arch-davinci/emac_defs.h
index b0ec8f5..35a1585 100644
--- a/arch/arm/include/asm/arch-davinci/emac_defs.h
+++ b/arch/arm/include/asm/arch-davinci/emac_defs.h
@@ -85,7 +85,7 @@
 #endif
 
 /* PHY mask - set only those phy number bits where phy is/can be connected */
-#define EMAC_MDIO_PHY_NUM           1
+#define EMAC_MDIO_PHY_NUM           CONFIG_EMAC_MDIO_PHY_NUM
 #define EMAC_MDIO_PHY_MASK          (1 << EMAC_MDIO_PHY_NUM)
 
 /* Ethernet Min/Max packet size */
diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h
index 0f58e11..160ece2 100644
--- a/include/configs/da830evm.h
+++ b/include/configs/da830evm.h
@@ -87,6 +87,7 @@
  * Network & Ethernet Configuration
  */
 #ifdef CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM	1
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
diff --git a/include/configs/davinci_dm365evm.h b/include/configs/davinci_dm365evm.h
index 6f99ae0..2c3d88d 100644
--- a/include/configs/davinci_dm365evm.h
+++ b/include/configs/davinci_dm365evm.h
@@ -58,6 +58,7 @@
 
 /* Network Configuration */
 #define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM	0
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h
index 5774df5..aab2afa 100644
--- a/include/configs/davinci_dvevm.h
+++ b/include/configs/davinci_dvevm.h
@@ -102,6 +102,7 @@
 /* Network & Ethernet Configuration */
 /*==================================*/
 #define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM	1
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
diff --git a/include/configs/davinci_schmoogie.h b/include/configs/davinci_schmoogie.h
index 3972ebc..875dda4 100644
--- a/include/configs/davinci_schmoogie.h
+++ b/include/configs/davinci_schmoogie.h
@@ -69,6 +69,7 @@
 /* Network & Ethernet Configuration */
 /*==================================*/
 #define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM	1
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h
index 94be9dc..f4e17f8 100644
--- a/include/configs/davinci_sffsdr.h
+++ b/include/configs/davinci_sffsdr.h
@@ -66,6 +66,7 @@
 #define CONFIG_SYS_I2C_SLAVE		10	/* Bogus, master-only in U-Boot */
 /* Network & Ethernet Configuration */
 #define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM	1
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
diff --git a/include/configs/davinci_sonata.h b/include/configs/davinci_sonata.h
index 490821a..4c01844 100644
--- a/include/configs/davinci_sonata.h
+++ b/include/configs/davinci_sonata.h
@@ -102,6 +102,7 @@
 /* Network & Ethernet Configuration */
 /*==================================*/
 #define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM	1
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
-- 
cgit v1.1


From 77436d6696127dcaa9049db47b000da7f2b8e85e Mon Sep 17 00:00:00 2001
From: Nick Thompson <nick.thompson@ge.com>
Date: Tue, 22 Jun 2010 11:06:01 -0400
Subject: Davinci: SPI performance enhancements

The following restructuring and optimisations increase the SPI
read performance from 1.3MiB/s (on da850) to 2.87MiB/s (on da830):

Remove continual revaluation of driver state from the core of the
copy loop. State can not change during the copy loop, so it is
possible to move these evaluations to before the copy loop.

Cost is more code space as loop variants are required for each set
of possible configurations. The loops are simpler however, so the
extra is only 128bytes on da830 with CONFIG_SPI_HALF_DUPLEX
defined.

Unrolling the first copy loop iteration allows the TX buffer to be
pre-loaded reducing SPI clock starvation.

Unrolling the last copy loop iteration removes testing for the
final loop iteration every time round the loop.

Using the RX buffer empty flag as a transfer throttle allows the
assumption that it is always safe to write to the TX buffer, so
polling of TX buffer full flag can be removed.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
---
 drivers/spi/davinci_spi.c | 195 ++++++++++++++++++++++++++++++----------------
 1 file changed, 128 insertions(+), 67 deletions(-)

diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c
index 08f837b..4518ecb 100644
--- a/drivers/spi/davinci_spi.c
+++ b/drivers/spi/davinci_spi.c
@@ -66,7 +66,7 @@ void spi_free_slave(struct spi_slave *slave)
 int spi_claim_bus(struct spi_slave *slave)
 {
 	struct davinci_spi_slave *ds = to_davinci_spi(slave);
-	unsigned int scalar, data1_reg_val = 0;
+	unsigned int scalar;
 
 	/* Enable the SPI hardware */
 	writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
@@ -93,11 +93,6 @@ int spi_claim_bus(struct spi_slave *slave)
 	writel(8 | (scalar << SPIFMT_PRESCALE_SHIFT) |
 		(1 << SPIFMT_PHASE_SHIFT), &ds->regs->fmt0);
 
-	/* hold cs active at end of transfer until explicitly de-asserted */
-	data1_reg_val = (1 << SPIDAT1_CSHOLD_SHIFT) |
-			(slave->cs << SPIDAT1_CSNR_SHIFT);
-	writel(data1_reg_val, &ds->regs->dat1);
-
 	/*
 	 * Including a minor delay. No science here. Should be good even with
 	 * no delay
@@ -113,8 +108,7 @@ int spi_claim_bus(struct spi_slave *slave)
 	writel(0, &ds->regs->lvl);
 
 	/* enable SPI */
-	writel((readl(&ds->regs->gcr1) |
-		SPIGCR1_SPIENA_MASK), &ds->regs->gcr1);
+	writel((readl(&ds->regs->gcr1) | SPIGCR1_SPIENA_MASK), &ds->regs->gcr1);
 
 	return 0;
 }
@@ -127,14 +121,125 @@ void spi_release_bus(struct spi_slave *slave)
 	writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
 }
 
+/*
+ * This functions needs to act like a macro to avoid pipeline reloads in the
+ * loops below. Use always_inline. This gains us about 160KiB/s and the bloat
+ * appears to be zero bytes (da830).
+ */
+__attribute__((always_inline))
+static inline u32 davinci_spi_xfer_data(struct davinci_spi_slave *ds, u32 data)
+{
+	u32	buf_reg_val;
+
+	/* send out data */
+	writel(data, &ds->regs->dat1);
+
+	/* wait for the data to clock in/out */
+	while ((buf_reg_val = readl(&ds->regs->buf)) & SPIBUF_RXEMPTY_MASK)
+		;
+
+	return buf_reg_val;
+}
+
+static int davinci_spi_read(struct spi_slave *slave, unsigned int len,
+			    u8 *rxp, unsigned long flags)
+{
+	struct davinci_spi_slave *ds = to_davinci_spi(slave);
+	unsigned int data1_reg_val;
+
+	/* enable CS hold, CS[n] and clear the data bits */
+	data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
+			 (slave->cs << SPIDAT1_CSNR_SHIFT));
+
+	/* wait till TXFULL is deasserted */
+	while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
+		;
+
+	/* preload the TX buffer to avoid clock starvation */
+	writel(data1_reg_val, &ds->regs->dat1);
+
+	/* keep reading 1 byte until only 1 byte left */
+	while ((len--) > 1)
+		*rxp++ = davinci_spi_xfer_data(ds, data1_reg_val);
+
+	/* clear CS hold when we reach the end */
+	if (flags & SPI_XFER_END)
+		data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);
+
+	/* read the last byte */
+	*rxp = davinci_spi_xfer_data(ds, data1_reg_val);
+
+	return 0;
+}
+
+static int davinci_spi_write(struct spi_slave *slave, unsigned int len,
+		const u8 *txp, unsigned long flags)
+{
+	struct davinci_spi_slave *ds = to_davinci_spi(slave);
+	unsigned int data1_reg_val;
+
+	/* enable CS hold and clear the data bits */
+	data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
+			 (slave->cs << SPIDAT1_CSNR_SHIFT));
+
+	/* wait till TXFULL is deasserted */
+	while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
+		;
+
+	/* preload the TX buffer to avoid clock starvation */
+	if (len > 2) {
+		writel(data1_reg_val | *txp++, &ds->regs->dat1);
+		len--;
+	}
+
+	/* keep writing 1 byte until only 1 byte left */
+	while ((len--) > 1)
+		davinci_spi_xfer_data(ds, data1_reg_val | *txp++);
+
+	/* clear CS hold when we reach the end */
+	if (flags & SPI_XFER_END)
+		data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);
+
+	/* write the last byte */
+	davinci_spi_xfer_data(ds, data1_reg_val | *txp);
+
+	return 0;
+}
+
+#ifndef CONFIG_SPI_HALF_DUPLEX
+static int davinci_spi_read_write(struct spi_slave *slave, unsigned int len,
+				  u8 *rxp, const u8 *txp, unsigned long flags)
+{
+	struct davinci_spi_slave *ds = to_davinci_spi(slave);
+	unsigned int data1_reg_val;
+
+	/* enable CS hold and clear the data bits */
+	data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
+			 (slave->cs << SPIDAT1_CSNR_SHIFT));
+
+	/* wait till TXFULL is deasserted */
+	while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
+		;
+
+	/* keep reading and writing 1 byte until only 1 byte left */
+	while ((len--) > 1)
+		*rxp++ = davinci_spi_xfer_data(ds, data1_reg_val | *txp++);
+
+	/* clear CS hold when we reach the end */
+	if (flags & SPI_XFER_END)
+		data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);
+
+	/* read and write the last byte */
+	*rxp = davinci_spi_xfer_data(ds, data1_reg_val | *txp);
+
+	return 0;
+}
+#endif
+
 int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 		const void *dout, void *din, unsigned long flags)
 {
-	struct davinci_spi_slave *ds = to_davinci_spi(slave);
-	unsigned int	len, data1_reg_val = readl(&ds->regs->dat1);
-	unsigned int	i_cnt = 0, o_cnt = 0, buf_reg_val;
-	const u8	*txp = dout; /* dout can be NULL for read operation */
-	u8		*rxp = din;  /* din can be NULL for write operation */
+	unsigned int len;
 
 	if (bitlen == 0)
 		/* Finish any previously submitted transfers */
@@ -154,63 +259,19 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
 
 	len = bitlen / 8;
 
-	/* do an empty read to clear the current contents */
-	readl(&ds->regs->buf);
-
-	/* keep writing and reading 1 byte until done */
-	while ((i_cnt < len) || (o_cnt < len)) {
-		/* read RX buffer and flags */
-		buf_reg_val = readl(&ds->regs->buf);
-
-		/* if data is available */
-		if ((i_cnt < len) &&
-			(buf_reg_val & SPIBUF_RXEMPTY_MASK) == 0) {
-			/*
-			 * If there is no read buffer simply
-			 * ignore the read character
-			 */
-			if (rxp)
-				*rxp++ = buf_reg_val & 0xFF;
-			/* increment read words count */
-			i_cnt++;
-		}
-
-		/*
-		 * if the tx buffer is empty and there
-		 * is still data to transmit
-		 */
-		if ((o_cnt < len) &&
-			((buf_reg_val & SPIBUF_TXFULL_MASK) == 0)) {
-			/* write the data */
-			data1_reg_val &= ~0xFFFF;
-			if (txp)
-				data1_reg_val |= *txp++;
-			/*
-			 * Write to DAT1 is required to keep
-			 * the serial transfer going.
-			 * We just terminate when we reach the end.
-			 */
-			if ((o_cnt == (len - 1)) && (flags & SPI_XFER_END)) {
-				/* clear CS hold */
-				writel(data1_reg_val &
-						~(1 << SPIDAT1_CSHOLD_SHIFT),
-						&ds->regs->dat1);
-			} else {
-				/* enable CS hold and write TX register */
-				data1_reg_val |= ((1 << SPIDAT1_CSHOLD_SHIFT) |
-					(slave->cs << SPIDAT1_CSNR_SHIFT));
-				writel(data1_reg_val, &ds->regs->dat1);
-			}
-			/* increment written words count */
-			o_cnt++;
-		}
-	}
-	return 0;
+	if (!dout)
+		return davinci_spi_read(slave, len, din, flags);
+	else if (!din)
+		return davinci_spi_write(slave, len, dout, flags);
+#ifndef CONFIG_SPI_HALF_DUPLEX
+	else
+		return davinci_spi_read_write(slave, len, din, dout, flags);
+#endif
 
 out:
 	if (flags & SPI_XFER_END) {
-		writel(data1_reg_val &
-			~(1 << SPIDAT1_CSHOLD_SHIFT), &ds->regs->dat1);
+		u8 dummy = 0;
+		davinci_spi_write(slave, 1, &dummy, flags);
 	}
 	return 0;
 }
-- 
cgit v1.1


From ee80fa7b6e96a43d4270700cddc884e00cdd99fd Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Sun, 13 Jun 2010 18:38:23 +0200
Subject: Get rid of bogus CONFIG_SYS_BUS_HZ and CONFIG_SYS_CONFIG_BUS_CLK
 definitions

CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality.  Change all this to use CONFIG_SYS_BUS_CLK consistently.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
---
 arch/powerpc/cpu/74xx_7xx/cpu.c    | 14 ++++++--------
 board/Marvell/db64360/sdram_init.c | 12 ++++++------
 board/Marvell/db64460/sdram_init.c | 12 ++++++------
 board/evb64260/mpsc.c              |  2 +-
 include/configs/BAB7xx.h           |  5 ++---
 include/configs/CPCI750.h          |  3 +--
 include/configs/DB64360.h          |  3 +--
 include/configs/DB64460.h          |  3 +--
 include/configs/ELPPC.h            |  5 ++---
 include/configs/EVB64260.h         |  3 +--
 include/configs/P3G4.h             |  3 +--
 include/configs/PCIPPC2.h          |  3 +--
 include/configs/PCIPPC6.h          |  3 +--
 include/configs/ZUMA.h             |  4 +---
 include/configs/mpc7448hpc2.h      |  2 +-
 include/configs/p3mx.h             |  6 ++----
 include/configs/ppmc7xx.h          |  4 +---
 17 files changed, 35 insertions(+), 52 deletions(-)

diff --git a/arch/powerpc/cpu/74xx_7xx/cpu.c b/arch/powerpc/cpu/74xx_7xx/cpu.c
index 3c17277..9248702 100644
--- a/arch/powerpc/cpu/74xx_7xx/cpu.c
+++ b/arch/powerpc/cpu/74xx_7xx/cpu.c
@@ -277,19 +277,17 @@ do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 /*
  * For the 7400 the TB clock runs at 1/4 the cpu bus speed.
  */
-#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SYS_CONFIG_BUS_CLK)
+#if defined(CONFIG_AMIGAONEG3SE) || !defined(CONFIG_SYS_BUS_CLK)
+#define	CONFIG_SYS_BUS_CLK gd->bus_clk
+#endif
+
 unsigned long get_tbclk(void)
 {
-	return (gd->bus_clk / 4);
+	return CONFIG_SYS_BUS_CLK / 4;
 }
-#else	/* ! CONFIG_AMIGAONEG3SE and !CONFIG_SYS_CONFIG_BUS_CLK*/
 
-unsigned long get_tbclk (void)
-{
-	return CONFIG_SYS_BUS_HZ / 4;
-}
-#endif	/* CONFIG_AMIGAONEG3SE or CONFIG_SYS_CONFIG_BUS_CLK*/
 /* ------------------------------------------------------------------------- */
+
 #if defined(CONFIG_WATCHDOG)
 #if !defined(CONFIG_PCIPPC2) && !defined(CONFIG_BAB7xx)
 void
diff --git a/board/Marvell/db64360/sdram_init.c b/board/Marvell/db64360/sdram_init.c
index d0817d7..d52d3f0 100644
--- a/board/Marvell/db64360/sdram_init.c
+++ b/board/Marvell/db64360/sdram_init.c
@@ -1290,37 +1290,37 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	case 0x0:
 	case 0x80:		/* refresh period is 15.625 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_HZ)
+			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_CLK)
 					/ (float) 1000000.0);
 		break;
 	case 0x1:
 	case 0x81:		/* refresh period is 3.9 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x2:
 	case 0x82:		/* refresh period is 7.8 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x3:
 	case 0x83:		/* refresh period is 31.3 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x4:
 	case 0x84:		/* refresh period is 62.5 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x5:
 	case 0x85:		/* refresh period is 125 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	default:		/* refresh period undefined */
diff --git a/board/Marvell/db64460/sdram_init.c b/board/Marvell/db64460/sdram_init.c
index 6d6b126..e328d8f 100644
--- a/board/Marvell/db64460/sdram_init.c
+++ b/board/Marvell/db64460/sdram_init.c
@@ -1289,37 +1289,37 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	case 0x0:
 	case 0x80:		/* refresh period is 15.625 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_HZ)
+			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_CLK)
 					/ (float) 1000000.0);
 		break;
 	case 0x1:
 	case 0x81:		/* refresh period is 3.9 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x2:
 	case 0x82:		/* refresh period is 7.8 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x3:
 	case 0x83:		/* refresh period is 31.3 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x4:
 	case 0x84:		/* refresh period is 62.5 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x5:
 	case 0x85:		/* refresh period is 125 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	default:		/* refresh period undefined */
diff --git a/board/evb64260/mpsc.c b/board/evb64260/mpsc.c
index 8c4a4c8..bee04fd 100644
--- a/board/evb64260/mpsc.c
+++ b/board/evb64260/mpsc.c
@@ -390,7 +390,7 @@ galbrg_set_baudrate(int channel, int rate)
 
 #if defined(CONFIG_ZUMA_V2) || defined(CONFIG_P3G4)
 	/* from tclk */
-	clock = (CONFIG_SYS_BUS_HZ/(16*rate)) - 1;
+	clock = (CONFIG_SYS_BUS_CLK/(16*rate)) - 1;
 #else
 	clock = (3686400/(16*rate)) - 1;
 #endif
diff --git a/include/configs/BAB7xx.h b/include/configs/BAB7xx.h
index 40a1c40..4d83786 100644
--- a/include/configs/BAB7xx.h
+++ b/include/configs/BAB7xx.h
@@ -436,9 +436,8 @@ extern unsigned char   scsi_sym53c8xx_ccf;
 extern  unsigned long           bab7xx_get_bus_freq (void);
 extern  unsigned long           bab7xx_get_gclk_freq (void);
 #endif
-#define CONFIG_SYS_BUS_HZ              bab7xx_get_bus_freq()
-#define CONFIG_SYS_BUS_CLK             CONFIG_SYS_BUS_HZ
-#define CONFIG_SYS_CPU_CLK             bab7xx_get_gclk_freq()
+#define CONFIG_SYS_BUS_CLK	bab7xx_get_bus_freq()
+#define CONFIG_SYS_CPU_CLK	bab7xx_get_gclk_freq()
 
 /*
  * For booting Linux, the board info and command line data
diff --git a/include/configs/CPCI750.h b/include/configs/CPCI750.h
index 1c8c68b..f2d51f7 100644
--- a/include/configs/CPCI750.h
+++ b/include/configs/CPCI750.h
@@ -234,8 +234,7 @@
 #define CONFIG_SYS_LOAD_ADDR		0x00300000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
diff --git a/include/configs/DB64360.h b/include/configs/DB64360.h
index 160871b..910933a 100644
--- a/include/configs/DB64360.h
+++ b/include/configs/DB64360.h
@@ -318,8 +318,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
 /*ronen - this the Sys clock (cpu bus,internal dram and SDRAM) */
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
 
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP 7 /* define the SDRAM cycle count */
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP 50 /* for 400MHZ -> 5.0 ns, for 133MHZ -> 7.50 ns */
diff --git a/include/configs/DB64460.h b/include/configs/DB64460.h
index 06fd157..765eaaf 100644
--- a/include/configs/DB64460.h
+++ b/include/configs/DB64460.h
@@ -256,8 +256,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
 /*ronen - this the Sys clock (cpu bus,internal dram and SDRAM) */
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
 
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP 7 /* define the SDRAM cycle count */
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP 50 /* for 200MHZ -> 5.0 ns, 166MHZ -> 6.0, 133MHZ -> 7.50 ns */
diff --git a/include/configs/ELPPC.h b/include/configs/ELPPC.h
index d2aa8b9..84d27b6 100644
--- a/include/configs/ELPPC.h
+++ b/include/configs/ELPPC.h
@@ -314,9 +314,8 @@
 /*
  * Speed settings are board specific
  */
-#define CONFIG_SYS_BUS_HZ              100000000
-#define CONFIG_SYS_CPU_CLK             400000000
-#define CONFIG_SYS_BUS_CLK             CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK	100000000
+#define CONFIG_SYS_CPU_CLK	400000000
 
 /*
  * For booting Linux, the board info and command line data
diff --git a/include/configs/EVB64260.h b/include/configs/EVB64260.h
index bf41c13..0903536 100644
--- a/include/configs/EVB64260.h
+++ b/include/configs/EVB64260.h
@@ -141,8 +141,7 @@
 #define	CONFIG_SYS_LOAD_ADDR		0x00300000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks	*/
-#define CONFIG_SYS_BUS_HZ		100000000	/* 100 MHz		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		100000000	/* 100 MHz		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
diff --git a/include/configs/P3G4.h b/include/configs/P3G4.h
index 971338a..890170d 100644
--- a/include/configs/P3G4.h
+++ b/include/configs/P3G4.h
@@ -168,8 +168,7 @@
 #define	CONFIG_SYS_LOAD_ADDR		0x00300000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks	*/
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
diff --git a/include/configs/PCIPPC2.h b/include/configs/PCIPPC2.h
index 99a8c4a..c30ac78 100644
--- a/include/configs/PCIPPC2.h
+++ b/include/configs/PCIPPC2.h
@@ -194,9 +194,8 @@
  * For the detail description refer to the PCIPPC2 user's manual.
  */
 #define CONFIG_SYS_HZ		      1000
-#define CONFIG_SYS_BUS_HZ            100000000 /* bus speed - 100 mhz          */
+#define CONFIG_SYS_BUS_CLK            100000000 /* bus speed - 100 mhz          */
 #define CONFIG_SYS_CPU_CLK	      300000000
-#define CONFIG_SYS_BUS_CLK	      100000000
 
 /*
  * For booting Linux, the board info and command line data
diff --git a/include/configs/PCIPPC6.h b/include/configs/PCIPPC6.h
index 66e6d24..bc67480 100644
--- a/include/configs/PCIPPC6.h
+++ b/include/configs/PCIPPC6.h
@@ -196,9 +196,8 @@
  * For the detail description refer to the PCIPPC2 user's manual.
  */
 #define CONFIG_SYS_HZ		      1000
-#define CONFIG_SYS_BUS_HZ	      100000000 /* bus speed - 100 mhz		*/
+#define CONFIG_SYS_BUS_CLK	      100000000 /* bus speed - 100 mhz		*/
 #define CONFIG_SYS_CPU_CLK	      300000000
-#define CONFIG_SYS_BUS_CLK	      100000000
 
 /*
  * For booting Linux, the board info and command line data
diff --git a/include/configs/ZUMA.h b/include/configs/ZUMA.h
index b73aaa8..fcc47a9 100644
--- a/include/configs/ZUMA.h
+++ b/include/configs/ZUMA.h
@@ -164,9 +164,7 @@
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
 
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz		*/
-
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h
index be12186..497ea42 100644
--- a/include/configs/mpc7448hpc2.h
+++ b/include/configs/mpc7448hpc2.h
@@ -46,7 +46,7 @@
 #define CONFIG_IDENT_STRING	" Freescale MPC7448 HPC II"
 
 #define CONFIG_SYS_OCN_CLK		133000000	/* 133 MHz */
-#define CONFIG_SYS_CONFIG_BUS_CLK	133000000
+#define CONFIG_SYS_BUS_CLK		133000000
 
 #define CONFIG_SYS_CLK_SPREAD		/* Enable Spread-Spectrum Clock generation */
 
diff --git a/include/configs/p3mx.h b/include/configs/p3mx.h
index 0749037..17ec08f 100644
--- a/include/configs/p3mx.h
+++ b/include/configs/p3mx.h
@@ -44,14 +44,12 @@
 #define CONFIG_750FX			/* 750GL/GX/FX			*/
 #define CONFIG_HIGH_BATS		/* High BATs supported		*/
 #define CONFIG_SYS_BOARD_NAME		"P3M750"
-#define CONFIG_SYS_BUS_HZ		100000000
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		100000000
 #define CONFIG_SYS_TCLK		100000000
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_74xx
 #define CONFIG_SYS_BOARD_NAME		"P3M7448"
-#define CONFIG_SYS_BUS_HZ		133333333
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133333333
 #define CONFIG_SYS_TCLK		133333333
 #endif
 #define CONFIG_SYS_GT_DUAL_CPU			/* also for JTAG even with one cpu */
diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h
index 0fd8635..04779c4 100644
--- a/include/configs/ppmc7xx.h
+++ b/include/configs/ppmc7xx.h
@@ -355,12 +355,10 @@
 /*
  * Clocks config
  *
- * CONFIG_SYS_BUS_HZ			- Bus clock frequency in Hz
- * CONFIG_SYS_BUS_CLK			- As above (?)
+ * CONFIG_SYS_BUS_CLK			- Bus clock frequency in Hz
  * CONFIG_SYS_HZ			- Decrementer freq in Hz
  */
 
-#define CONFIG_SYS_BUS_HZ		CONFIG_BUS_CLK
 #define CONFIG_SYS_BUS_CLK		CONFIG_BUS_CLK
 #define CONFIG_SYS_HZ			1000
 
-- 
cgit v1.1


From 953b7e629198fe2eb0adf272fb9140f2a4a51826 Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Sun, 13 Jun 2010 18:28:54 +0200
Subject: Remove AmigaOneG3SE board

The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years.  As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 arch/powerpc/cpu/74xx_7xx/cpu.c         |    7 +-
 arch/powerpc/cpu/74xx_7xx/interrupts.c  |   11 +-
 arch/powerpc/cpu/74xx_7xx/speed.c       |    4 -
 arch/powerpc/cpu/74xx_7xx/start.S       |    5 +-
 arch/powerpc/cpu/74xx_7xx/traps.c       |    8 -
 board/MAI/AmigaOneG3SE/AmigaOneG3SE.c   |  122 ----
 board/MAI/AmigaOneG3SE/Makefile         |   63 --
 board/MAI/AmigaOneG3SE/articiaS.c       |  704 ------------------
 board/MAI/AmigaOneG3SE/articiaS.h       |  142 ----
 board/MAI/AmigaOneG3SE/articiaS_pci.c   |  576 ---------------
 board/MAI/AmigaOneG3SE/board_asm_init.S |  156 ----
 board/MAI/AmigaOneG3SE/cmd_boota.c      |  128 ----
 board/MAI/AmigaOneG3SE/config.mk        |   32 -
 board/MAI/AmigaOneG3SE/enet.c           |  840 ----------------------
 board/MAI/AmigaOneG3SE/flash.c          |   35 -
 board/MAI/AmigaOneG3SE/flash_new.c      |  651 -----------------
 board/MAI/AmigaOneG3SE/i8259.c          |  230 ------
 board/MAI/AmigaOneG3SE/i8259.h          |   56 --
 board/MAI/AmigaOneG3SE/interrupts.c     |  266 -------
 board/MAI/AmigaOneG3SE/macros.h         |   84 ---
 board/MAI/AmigaOneG3SE/memio.S          |   67 --
 board/MAI/AmigaOneG3SE/memio.h          |  113 ---
 board/MAI/AmigaOneG3SE/memory_dump      |   30 -
 board/MAI/AmigaOneG3SE/nvram.c          |   36 -
 board/MAI/AmigaOneG3SE/ps2kbd.c         |  685 ------------------
 board/MAI/AmigaOneG3SE/ps2kbd.h         |   41 --
 board/MAI/AmigaOneG3SE/serial.c         |  245 -------
 board/MAI/AmigaOneG3SE/short_types.h    |   36 -
 board/MAI/AmigaOneG3SE/smbus.c          |  206 ------
 board/MAI/AmigaOneG3SE/smbus.h          |   22 -
 board/MAI/AmigaOneG3SE/start.txt        |  198 ------
 board/MAI/AmigaOneG3SE/todo.txt         |    3 -
 board/MAI/AmigaOneG3SE/u-boot.lds       |  136 ----
 board/MAI/AmigaOneG3SE/usb_uhci.c       | 1178 -------------------------------
 board/MAI/AmigaOneG3SE/usb_uhci.h       |  192 -----
 board/MAI/AmigaOneG3SE/via686.c         |  299 --------
 board/MAI/AmigaOneG3SE/via686.h         |   29 -
 board/MAI/AmigaOneG3SE/video.c          |  541 --------------
 board/MAI/menu/cmd_menu.c               |   16 -
 boards.cfg                              |    1 -
 common/cmd_bootm.c                      |    9 -
 common/cmd_fdc.c                        |   60 --
 common/cmd_ide.c                        |  106 +--
 common/cmd_nvedit.c                     |   12 -
 common/console.c                        |    4 -
 common/env_common.c                     |   28 -
 common/env_nvram.c                      |   32 -
 common/main.c                           |    9 +-
 drivers/rtc/mc146818.c                  |    7 -
 drivers/rtc/mk48t59.c                   |   18 -
 include/configs/AmigaOneG3SE.h          |  404 -----------
 51 files changed, 15 insertions(+), 8868 deletions(-)
 delete mode 100644 board/MAI/AmigaOneG3SE/AmigaOneG3SE.c
 delete mode 100644 board/MAI/AmigaOneG3SE/Makefile
 delete mode 100644 board/MAI/AmigaOneG3SE/articiaS.c
 delete mode 100644 board/MAI/AmigaOneG3SE/articiaS.h
 delete mode 100644 board/MAI/AmigaOneG3SE/articiaS_pci.c
 delete mode 100644 board/MAI/AmigaOneG3SE/board_asm_init.S
 delete mode 100644 board/MAI/AmigaOneG3SE/cmd_boota.c
 delete mode 100644 board/MAI/AmigaOneG3SE/config.mk
 delete mode 100644 board/MAI/AmigaOneG3SE/enet.c
 delete mode 100644 board/MAI/AmigaOneG3SE/flash.c
 delete mode 100644 board/MAI/AmigaOneG3SE/flash_new.c
 delete mode 100644 board/MAI/AmigaOneG3SE/i8259.c
 delete mode 100644 board/MAI/AmigaOneG3SE/i8259.h
 delete mode 100644 board/MAI/AmigaOneG3SE/interrupts.c
 delete mode 100644 board/MAI/AmigaOneG3SE/macros.h
 delete mode 100644 board/MAI/AmigaOneG3SE/memio.S
 delete mode 100644 board/MAI/AmigaOneG3SE/memio.h
 delete mode 100644 board/MAI/AmigaOneG3SE/memory_dump
 delete mode 100644 board/MAI/AmigaOneG3SE/nvram.c
 delete mode 100644 board/MAI/AmigaOneG3SE/ps2kbd.c
 delete mode 100644 board/MAI/AmigaOneG3SE/ps2kbd.h
 delete mode 100644 board/MAI/AmigaOneG3SE/serial.c
 delete mode 100644 board/MAI/AmigaOneG3SE/short_types.h
 delete mode 100644 board/MAI/AmigaOneG3SE/smbus.c
 delete mode 100644 board/MAI/AmigaOneG3SE/smbus.h
 delete mode 100644 board/MAI/AmigaOneG3SE/start.txt
 delete mode 100644 board/MAI/AmigaOneG3SE/todo.txt
 delete mode 100644 board/MAI/AmigaOneG3SE/u-boot.lds
 delete mode 100644 board/MAI/AmigaOneG3SE/usb_uhci.c
 delete mode 100644 board/MAI/AmigaOneG3SE/usb_uhci.h
 delete mode 100644 board/MAI/AmigaOneG3SE/via686.c
 delete mode 100644 board/MAI/AmigaOneG3SE/via686.h
 delete mode 100644 board/MAI/AmigaOneG3SE/video.c
 delete mode 100644 board/MAI/menu/cmd_menu.c
 delete mode 100644 include/configs/AmigaOneG3SE.h

diff --git a/arch/powerpc/cpu/74xx_7xx/cpu.c b/arch/powerpc/cpu/74xx_7xx/cpu.c
index 9248702..14d3ce4 100644
--- a/arch/powerpc/cpu/74xx_7xx/cpu.c
+++ b/arch/powerpc/cpu/74xx_7xx/cpu.c
@@ -49,11 +49,6 @@
 #include <fdt_support.h>
 #endif
 
-#ifdef CONFIG_AMIGAONEG3SE
-#include "../board/MAI/AmigaOneG3SE/via686.h"
-#include "../board/MAI/AmigaOneG3SE/memio.h"
-#endif
-
 DECLARE_GLOBAL_DATA_PTR;
 
 cpu_t
@@ -277,7 +272,7 @@ do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 /*
  * For the 7400 the TB clock runs at 1/4 the cpu bus speed.
  */
-#if defined(CONFIG_AMIGAONEG3SE) || !defined(CONFIG_SYS_BUS_CLK)
+#ifndef CONFIG_SYS_BUS_CLK
 #define	CONFIG_SYS_BUS_CLK gd->bus_clk
 #endif
 
diff --git a/arch/powerpc/cpu/74xx_7xx/interrupts.c b/arch/powerpc/cpu/74xx_7xx/interrupts.c
index 0ea1aec..c2856c9 100644
--- a/arch/powerpc/cpu/74xx_7xx/interrupts.c
+++ b/arch/powerpc/cpu/74xx_7xx/interrupts.c
@@ -34,20 +34,19 @@
 
 int interrupt_init_cpu (unsigned *decrementer_count)
 {
-#if defined(DEBUG) && !defined(CONFIG_AMIGAONEG3SE)
-	printf("interrupt_init: GT main cause reg: %08x:%08x\n",
+	debug("interrupt_init: GT main cause reg: %08x:%08x\n",
 	       GTREGREAD(LOW_INTERRUPT_CAUSE_REGISTER),
 	       GTREGREAD(HIGH_INTERRUPT_CAUSE_REGISTER));
-	printf("interrupt_init: ethernet cause regs: %08x %08x %08x\n",
+	debug("interrupt_init: ethernet cause regs: %08x %08x %08x\n",
 	       GTREGREAD(ETHERNET0_INTERRUPT_CAUSE_REGISTER),
 	       GTREGREAD(ETHERNET1_INTERRUPT_CAUSE_REGISTER),
 	       GTREGREAD(ETHERNET2_INTERRUPT_CAUSE_REGISTER));
-	printf("interrupt_init: ethernet mask regs:  %08x %08x %08x\n",
+	debug("interrupt_init: ethernet mask regs:  %08x %08x %08x\n",
 	       GTREGREAD(ETHERNET0_INTERRUPT_MASK_REGISTER),
 	       GTREGREAD(ETHERNET1_INTERRUPT_MASK_REGISTER),
 	       GTREGREAD(ETHERNET2_INTERRUPT_MASK_REGISTER));
-	puts("interrupt_init: setting decrementer_count\n");
-#endif
+	debug("interrupt_init: setting decrementer_count\n");
+
 	*decrementer_count = get_tbclk() / CONFIG_SYS_HZ;
 
 	return (0);
diff --git a/arch/powerpc/cpu/74xx_7xx/speed.c b/arch/powerpc/cpu/74xx_7xx/speed.c
index f2fdcd5..6450c3c 100644
--- a/arch/powerpc/cpu/74xx_7xx/speed.c
+++ b/arch/powerpc/cpu/74xx_7xx/speed.c
@@ -25,10 +25,6 @@
 #include <74xx_7xx.h>
 #include <asm/processor.h>
 
-#ifdef CONFIG_AMIGAONEG3SE
-#include "../board/MAI/AmigaOneG3SE/via686.h"
-#endif
-
 DECLARE_GLOBAL_DATA_PTR;
 
 extern unsigned long get_board_bus_clk (void);
diff --git a/arch/powerpc/cpu/74xx_7xx/start.S b/arch/powerpc/cpu/74xx_7xx/start.S
index 88fdf88..a36af5a 100644
--- a/arch/powerpc/cpu/74xx_7xx/start.S
+++ b/arch/powerpc/cpu/74xx_7xx/start.S
@@ -745,9 +745,8 @@ in_ram:
 	bne	5b
 6:
 	mr	r3, r10		/* Destination Address		*/
-#if defined(CONFIG_AMIGAONEG3SE) || \
-    defined(CONFIG_DB64360)	 || \
-    defined(CONFIG_DB64460)      || \
+#if defined(CONFIG_DB64360)	|| \
+    defined(CONFIG_DB64460)     || \
     defined(CONFIG_CPCI750)	|| \
     defined(CONFIG_PPMC7XX)     || \
     defined(CONFIG_P3Mx)
diff --git a/arch/powerpc/cpu/74xx_7xx/traps.c b/arch/powerpc/cpu/74xx_7xx/traps.c
index 5073b05..7ae81eb 100644
--- a/arch/powerpc/cpu/74xx_7xx/traps.c
+++ b/arch/powerpc/cpu/74xx_7xx/traps.c
@@ -37,20 +37,12 @@
 #include <kgdb.h>
 #include <asm/processor.h>
 
-#ifdef CONFIG_AMIGAONEG3SE
-DECLARE_GLOBAL_DATA_PTR;
-#endif
-
 /* Returns 0 if exception not found and fixup otherwise.  */
 extern unsigned long search_exception_table(unsigned long);
 
 /* THIS NEEDS CHANGING to use the board info structure.
 */
-#ifdef CONFIG_AMIGAONEG3SE
-#define END_OF_MEM (gd->bd->bi_memstart + gd->bd->bi_memsize)
-#else
 #define END_OF_MEM	0x02000000
-#endif
 
 /*
  * Trap & Exception support
diff --git a/board/MAI/AmigaOneG3SE/AmigaOneG3SE.c b/board/MAI/AmigaOneG3SE/AmigaOneG3SE.c
deleted file mode 100644
index 4d44001..0000000
--- a/board/MAI/AmigaOneG3SE/AmigaOneG3SE.c
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * (C) Copyright 2002
- * Hyperion Entertainment, ThomasF@hyperion-entertainment.com
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <command.h>
-#include <pci.h>
-#include <netdev.h>
-#include "articiaS.h"
-#include "memio.h"
-#include "via686.h"
-
-__asm__(" .globl send_kb				\n "
-	"send_kb:					\n "
-	"	lis	r9, 0xfe00			\n "
-	"						\n "
-	"	li	r4, 0x10	# retries	\n "
-	"	mtctr	r4				\n "
-	"						\n "
-	"idle:						\n "
-	"	lbz	r4, 0x64(r9)			\n "
-	"	andi.	r4, r4, 0x02			\n "
-	"	bne	idle				\n "
-
-	"ready:						\n "
-	"	stb	r3, 0x60(r9)			\n "
-	"						\n "
-	"check:						\n "
-	"	lbz	r4, 0x64(r9)			\n "
-	"	andi.	r4, r4, 0x01			\n "
-	"	beq	check				\n "
-	"						\n "
-	"	lbz	r4, 0x60(r9)			\n "
-	"	cmpwi	r4, 0xfa			\n "
-	"	beq	done				\n "
-
-	"	bdnz	idle				\n "
-
-	"	li	r3, 0				\n "
-	"	blr					\n "
-
-	"done:						\n "
-	"	li	r3, 1				\n "
-	"	blr					\n "
-
-	".globl test_kb					\n "
-	"test_kb:					\n "
-	"	mflr	r10				\n "
-	"	li	r3, 0xed			\n "
-	"	bl	send_kb				\n "
-	"	li	r3, 0x01			\n "
-	"	bl	send_kb				\n "
-	"	mtlr	r10				\n "
-	"	blr					\n "
-);
-
-
-int checkboard (void)
-{
-	printf ("Board: AmigaOneG3SE\n");
-	return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
-	return articiaS_ram_init ();
-}
-
-
-void after_reloc (ulong dest_addr, gd_t *gd)
-{
-	board_init_r (gd, dest_addr);
-}
-
-
-int misc_init_r (void)
-{
-	extern pci_dev_t video_dev;
-	extern void drv_video_init (void);
-
-	if (video_dev != ~0)
-		drv_video_init ();
-
-	return (0);
-}
-
-
-void pci_init_board (void)
-{
-#ifndef CONFIG_RAMBOOT
-	articiaS_pci_init ();
-#endif
-}
-
-int board_eth_init(bd_t *bis)
-{
-#if defined(CONFIG_3COM)
-	eth_3com_initialize(bis);
-#endif
-	return 0;
-}
diff --git a/board/MAI/AmigaOneG3SE/Makefile b/board/MAI/AmigaOneG3SE/Makefile
deleted file mode 100644
index fa28d3b..0000000
--- a/board/MAI/AmigaOneG3SE/Makefile
+++ /dev/null
@@ -1,63 +0,0 @@
-#
-# (C) Copyright 2002-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../menu)
-$(shell mkdir -p $(obj)../bios_emulator)
-endif
-
-LIB	= $(obj)lib$(BOARD).a
-
-COBJS	= $(BOARD).o articiaS.o flash.o serial.o smbus.o articiaS_pci.o \
-		via686.o i8259.o ../bios_emulator/x86interface.o	\
-		../bios_emulator/bios.o ../bios_emulator/glue.o		\
-		interrupts.o ps2kbd.o video.o usb_uhci.o enet.o	        \
-		../menu/cmd_menu.o cmd_boota.o nvram.o
-
-SOBJS	= board_asm_init.o memio.o
-
-EMUDIR  = ../bios_emulator/scitech/src/x86emu/
-EMUOBJ  = $(EMUDIR)decode.o $(EMUDIR)ops2.o $(EMUDIR)fpu.o $(EMUDIR)prim_ops.o \
-		$(EMUDIR)ops.o $(EMUDIR)sys.o
-EMUSRC  = $(EMUOBJ:.o=.c)
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-EMUOBJ  := $(addprefix $(obj),$(EMUOBJ))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS) $(EMUSRC)
-	make $(obj)libx86emu.a -C ../bios_emulator/scitech/src/x86emu -f makefile.uboot CROSS_COMPILE=$(CROSS_COMPILE)
-	-rm $(LIB)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) $(EMUOBJ)
-
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/MAI/AmigaOneG3SE/articiaS.c b/board/MAI/AmigaOneG3SE/articiaS.c
deleted file mode 100644
index 3901b80..0000000
--- a/board/MAI/AmigaOneG3SE/articiaS.c
+++ /dev/null
@@ -1,704 +0,0 @@
-/*
- * (C) Copyright 2002
- * Hyperion Entertainment, ThomasF@hyperion-entertainment.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include "memio.h"
-#include "articiaS.h"
-#include "smbus.h"
-#include "via686.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#undef DEBUG
-
-struct dimm_bank {
-	uint8 used;			/* Bank is populated */
-	uint32 rows;			/* Number of row addresses */
-	uint32 columns;			/* Number of column addresses */
-	uint8 registered;		/* SIMM is registered */
-	uint8 ecc;			/* SIMM has ecc */
-	uint8 burst_len;		/* Supported burst lengths */
-	uint32 cas_lat;			/* Supported CAS latencies */
-	uint32 cas_used;		/* CAS to use (not set by user) */
-	uint32 trcd;			/* RAS to CAS latency */
-	uint32 trp;			/* Precharge latency */
-	uint32 tclk_hi;			/* SDRAM cycle time (highest CAS latency) */
-	uint32 tclk_2hi;		/* SDRAM second highest CAS latency */
-	uint32 size;			/* Size of bank in bytes */
-	uint8 auto_refresh;		/* Module supports auto refresh */
-	uint32 refresh_time;		/* Refresh time (in ns) */
-};
-
-
-/*
-** Based in part on the evb64260 code
-*/
-
-/*
- * translate ns.ns/10 coding of SPD timing values
- * into 10 ps unit values
- */
-static inline unsigned short NS10to10PS (unsigned char spd_byte)
-{
-	unsigned short ns, ns10;
-
-	/* isolate upper nibble */
-	ns = (spd_byte >> 4) & 0x0F;
-	/* isolate lower nibble */
-	ns10 = (spd_byte & 0x0F);
-
-	return (ns * 100 + ns10 * 10);
-}
-
-/*
- * translate ns coding of SPD timing values
- * into 10 ps unit values
- */
-static inline unsigned short NSto10PS (unsigned char spd_byte)
-{
-	return (spd_byte * 100);
-}
-
-
-long detect_sdram (uint8 * rom, int dimmNum, struct dimm_bank *banks)
-{
-	int dimm_address = (dimmNum == 0) ? SM_DIMM0_ADDR : SM_DIMM1_ADDR;
-	uint32 busclock = gd->bus_clk;
-	uint32 memclock = busclock;
-	uint32 tmemclock = 1000000000 / (memclock / 100);
-	uint32 datawidth;
-
-	if (sm_get_data (rom, dimm_address) == 0) {
-		/* Nothing in slot, make both banks empty */
-		debug ("Slot %d: vacant\n", dimmNum);
-		banks[0].used = 0;
-		banks[1].used = 0;
-		return 0;
-	}
-
-	if (rom[2] != 0x04) {
-		debug ("Slot %d: No SDRAM\n", dimmNum);
-		banks[0].used = 0;
-		banks[1].used = 0;
-		return 0;
-	}
-
-	/* Determine number of banks/rows */
-	if (rom[5] == 1) {
-		banks[0].used = 1;
-		banks[1].used = 0;
-	} else {
-		banks[0].used = 1;
-		banks[1].used = 1;
-	}
-
-	/* Determine number of row addresses */
-	if (rom[3] & 0xf0) {
-		/* Different banks sizes */
-		banks[0].rows = rom[3] & 0x0f;
-		banks[1].rows = (rom[3] & 0xf0) >> 4;
-	} else {
-		/* Equal sized banks */
-		banks[0].rows = rom[3] & 0x0f;
-		banks[1].rows = banks[0].rows;
-	}
-
-	/* Determine number of column addresses */
-	if (rom[4] & 0xf0) {
-		/* Different bank sizes */
-		banks[0].columns = rom[4] & 0x0f;
-		banks[1].columns = (rom[4] & 0xf0) >> 4;
-	} else {
-		banks[0].columns = rom[4] & 0x0f;
-		banks[1].columns = banks[0].columns;
-	}
-
-	/* Check Jedec revision, and modify row/column accordingly */
-	if (rom[62] > 0x10) {
-		if (banks[0].rows <= 3)
-			banks[0].rows += 15;
-		if (banks[1].rows <= 3)
-			banks[1].rows += 15;
-		if (banks[0].columns <= 3)
-			banks[0].columns += 15;
-		if (banks[0].columns <= 3)
-			banks[0].columns += 15;
-	}
-
-	/* Check registered/unregisterd */
-	if (rom[21] & 0x12) {
-		banks[0].registered = 1;
-		banks[1].registered = 1;
-	} else {
-		banks[0].registered = 0;
-		banks[1].registered = 0;
-	}
-
-#ifdef CONFIG_ECC
-	/* Check parity/ECC */
-	banks[0].ecc = (rom[11] == 0x02);
-	banks[1].ecc = (rom[11] == 0x02);
-#endif
-
-	/* Find burst lengths supported */
-	banks[0].burst_len = rom[16] & 0x8f;
-	banks[1].burst_len = rom[16] & 0x8f;
-
-	/* Find possible cas latencies */
-	banks[0].cas_lat = rom[18] & 0x7F;
-	banks[1].cas_lat = rom[18] & 0x7F;
-
-	/* RAS/CAS latency */
-	banks[0].trcd = (NSto10PS (rom[29]) + (tmemclock - 1)) / tmemclock;
-	banks[1].trcd = (NSto10PS (rom[29]) + (tmemclock - 1)) / tmemclock;
-
-	/* Precharge latency */
-	banks[0].trp = (NSto10PS (rom[27]) + (tmemclock - 1)) / tmemclock;
-	banks[1].trp = (NSto10PS (rom[27]) + (tmemclock - 1)) / tmemclock;
-
-	/* highest CAS latency */
-	banks[0].tclk_hi = NS10to10PS (rom[9]);
-	banks[1].tclk_hi = NS10to10PS (rom[9]);
-
-	/* second highest CAS latency */
-	banks[0].tclk_2hi = NS10to10PS (rom[23]);
-	banks[1].tclk_2hi = NS10to10PS (rom[23]);
-
-	/* bank sizes */
-	datawidth = rom[13] & 0x7f;
-	banks[0].size =
-			(1L << (banks[0].rows + banks[0].columns)) *
-			/* FIXME datawidth */ 8 * rom[17];
-	if (rom[13] & 0x80)
-		banks[1].size = 2 * banks[0].size;
-	else
-		banks[1].size = (1L << (banks[1].rows + banks[1].columns)) *
-				/* FIXME datawidth */ 8 * rom[17];
-
-	/* Refresh */
-	if (rom[12] & 0x80) {
-		banks[0].auto_refresh = 1;
-		banks[1].auto_refresh = 1;
-	} else {
-		banks[0].auto_refresh = 0;
-		banks[1].auto_refresh = 0;
-	}
-
-	switch (rom[12] & 0x7f) {
-	case 0:
-		banks[0].refresh_time = (1562500 + (tmemclock - 1)) / tmemclock;
-		banks[1].refresh_time = (1562500 + (tmemclock - 1)) / tmemclock;
-		break;
-	case 1:
-		banks[0].refresh_time = (390600 + (tmemclock - 1)) / tmemclock;
-		banks[1].refresh_time = (390600 + (tmemclock - 1)) / tmemclock;
-		break;
-	case 2:
-		banks[0].refresh_time = (781200 + (tmemclock - 1)) / tmemclock;
-		banks[1].refresh_time = (781200 + (tmemclock - 1)) / tmemclock;
-		break;
-	case 3:
-		banks[0].refresh_time = (3125000 + (tmemclock - 1)) / tmemclock;
-		banks[1].refresh_time = (3125000 + (tmemclock - 1)) / tmemclock;
-		break;
-	case 4:
-		banks[0].refresh_time = (6250000 + (tmemclock - 1)) / tmemclock;
-		banks[1].refresh_time = (6250000 + (tmemclock - 1)) / tmemclock;
-		break;
-	case 5:
-		banks[0].refresh_time = (12500000 + (tmemclock - 1)) / tmemclock;
-		banks[1].refresh_time = (12500000 + (tmemclock - 1)) / tmemclock;
-		break;
-	default:
-		banks[0].refresh_time = 0x100;	/* Default of Articia S */
-		banks[1].refresh_time = 0x100;
-		break;
-	}
-
-#ifdef DEBUG
-	printf ("\nInformation for SIMM bank %ld:\n", dimmNum);
-	printf ("Number of banks: %ld\n", banks[0].used + banks[1].used);
-	printf ("Number of row addresses: %ld\n", banks[0].rows);
-	printf ("Number of coumns addresses: %ld\n", banks[0].columns);
-	printf ("SIMM is %sregistered\n",
-			banks[0].registered == 0 ? "not " : "");
-#ifdef CONFIG_ECC
-	printf ("SIMM %s ECC\n",
-			banks[0].ecc == 1 ? "supports" : "doesn't support");
-#endif
-	printf ("Supported burst lenghts: %s %s %s %s %s\n",
-			banks[0].burst_len & 0x08 ? "8" : " ",
-			banks[0].burst_len & 0x04 ? "4" : " ",
-			banks[0].burst_len & 0x02 ? "2" : " ",
-			banks[0].burst_len & 0x01 ? "1" : " ",
-			banks[0].burst_len & 0x80 ? "PAGE" : "    ");
-	printf ("Supported CAS latencies: %s %s %s\n",
-			banks[0].cas_lat & 0x04 ? "CAS 3" : "     ",
-			banks[0].cas_lat & 0x02 ? "CAS 2" : "     ",
-			banks[0].cas_lat & 0x01 ? "CAS 1" : "     ");
-	printf ("RAS to CAS latency: %ld\n", banks[0].trcd);
-	printf ("Precharge latency: %ld\n", banks[0].trp);
-	printf ("SDRAM highest CAS latency: %ld\n", banks[0].tclk_hi);
-	printf ("SDRAM 2nd highest CAS latency: %ld\n", banks[0].tclk_2hi);
-	printf ("SDRAM data width: %ld\n", datawidth);
-	printf ("Auto Refresh %ssupported\n",
-			banks[0].auto_refresh ? "" : "not ");
-	printf ("Refresh time: %ld clocks\n", banks[0].refresh_time);
-	if (banks[0].used)
-		printf ("Bank 0 size: %ld MB\n", banks[0].size / 1024 / 1024);
-	if (banks[1].used)
-		printf ("Bank 1 size: %ld MB\n", banks[1].size / 1024 / 1024);
-
-	printf ("\n");
-#endif
-
-	sm_term ();
-	return 1;
-}
-
-void select_cas (struct dimm_bank *banks, uint8 fast)
-{
-	if (!banks[0].used) {
-		banks[0].cas_used = 0;
-		banks[0].cas_used = 0;
-		return;
-	}
-
-	if (fast) {
-		/* Search for fast CAS */
-		uint32 i;
-		uint32 c = 0x01;
-
-		for (i = 1; i < 5; i++) {
-			if (banks[0].cas_lat & c) {
-				banks[0].cas_used = i;
-				banks[1].cas_used = i;
-				debug ("Using CAS %d (fast)\n", i);
-				return;
-			}
-			c <<= 1;
-		}
-
-		/* Default to CAS 3 */
-		banks[0].cas_used = 3;
-		banks[1].cas_used = 3;
-		debug ("Using CAS 3 (fast)\n");
-
-		return;
-	} else {
-		/* Search for slow cas */
-		uint32 i;
-		uint32 c = 0x08;
-
-		for (i = 4; i > 1; i--) {
-			if (banks[0].cas_lat & c) {
-				banks[0].cas_used = i;
-				banks[1].cas_used = i;
-				debug ("Using CAS %d (slow)\n", i);
-				return;
-			}
-			c >>= 1;
-		}
-
-		/* Default to CAS 3 */
-		banks[0].cas_used = 3;
-		banks[1].cas_used = 3;
-		debug ("Using CAS 3 (slow)\n");
-
-		return;
-	}
-
-	banks[0].cas_used = 3;
-	banks[1].cas_used = 3;
-	debug ("Using CAS 3\n");
-
-	return;
-}
-
-uint32 get_reg_setting (uint32 banks, uint32 rows, uint32 columns, uint32 size)
-{
-	uint32 i;
-
-	struct RowColumnSize {
-		uint32 banks;
-		uint32 rows;
-		uint32 columns;
-		uint32 size;
-		uint32 register_value;
-	};
-
-	struct RowColumnSize rcs_map[] = {
-		/*  Sbk Radr Cadr   MB     Value */
-		{1, 11, 8, 8, 0x00840f00},
-		{1, 11, 9, 16, 0x00925f00},
-		{1, 11, 10, 32, 0x00a64f00},
-		{2, 12, 8, 32, 0x00c55f00},
-		{2, 12, 9, 64, 0x00d66f00},
-		{2, 12, 10, 128, 0x00e77f00},
-		{2, 12, 11, 256, 0x00ff8f00},
-		{2, 13, 11, 512, 0x00ff9f00},
-		{0, 0, 0, 0, 0x00000000}
-	};
-
-
-	i = 0;
-
-	while (rcs_map[i].banks != 0) {
-		if (rows == rcs_map[i].rows
-			&& columns == rcs_map[i].columns
-			&& (size / 1024 / 1024) == rcs_map[i].size)
-			return rcs_map[i].register_value;
-
-		i++;
-	}
-
-	return 0;
-}
-
-uint32 burst_to_len (uint32 support)
-{
-	if (support & 0x80)
-		return 0x7;
-	else if (support & 0x8)
-		return 0x3;
-	else if (support & 0x4)
-		return 0x2;
-	else if (support & 0x2)
-		return 0x1;
-	else if (support & 0x1)
-		return 0x0;
-
-	return 0;
-}
-
-long articiaS_ram_init (void)
-{
-	register uint32 i;
-	register uint32 value1;
-	register uint32 value2;
-	uint8 rom[128];
-	uint32 burst_len;
-	uint32 burst_support;
-	uint32 total_ram = 0;
-
-	struct dimm_bank banks[4];	/* FIXME: Move to initram */
-	uint32 busclock = gd->bus_clk;
-	uint32 memclock = busclock;
-	uint32 reg32;
-	uint32 refresh_clocks;
-	uint8 auto_refresh;
-
-	memset (banks, 0, sizeof (struct dimm_bank) * 4);
-
-	detect_sdram (rom, 0, &banks[0]);
-	detect_sdram (rom, 1, &banks[2]);
-
-	for (i = 0; i < 4; i++) {
-		total_ram = total_ram + (banks[i].used * banks[i].size);
-	}
-
-	pci_write_cfg_long (0, 0, GLOBALINFO0, 0x117430c0);
-	pci_write_cfg_long (0, 0, HBUSACR0, 0x1f0100b0);
-	pci_write_cfg_long (0, 0, SRAM_CR, 0x00f12000);	/* Note: Might also try 0x00f10000 (original: 0x00f12000) */
-	pci_write_cfg_byte (0, 0, DRAM_RAS_CTL0, 0x3f);
-	pci_write_cfg_byte (0, 0, DRAM_RAS_CTL1, 0x00);	/*  was: 0x04); */
-	pci_write_cfg_word (0, 0, DRAM_ECC0, 0x2020);	/*  was: 0x2400);  No ECC yet */
-
-	/* FIXME: Move this stuff to seperate function, like setup_dimm_bank */
-	if (banks[0].used) {
-		value1 = get_reg_setting (banks[0].used + banks[1].used,
-					  banks[0].rows, banks[0].columns,
-					  banks[0].size);
-	} else {
-		value1 = 0;
-	}
-
-	if (banks[1].used) {
-		value2 = get_reg_setting (banks[0].used + banks[1].used,
-					  banks[1].rows, banks[1].columns,
-					  banks[1].size);
-	} else {
-		value2 = 0;
-	}
-
-	pci_write_cfg_long (0, 0, DIMM0_B0_SCR0, value1);
-	pci_write_cfg_long (0, 0, DIMM0_B1_SCR0, value2);
-
-	debug ("DIMM0_B0_SCR0 = 0x%08x\n", value1);
-	debug ("DIMM0_B1_SCR0 = 0x%08x\n", value2);
-
-	if (banks[2].used) {
-		value1 = get_reg_setting (banks[2].used + banks[3].used,
-					  banks[2].rows, banks[2].columns,
-					  banks[2].size);
-	} else {
-		value1 = 0;
-	}
-
-	if (banks[3].used) {
-		value2 = get_reg_setting (banks[2].used + banks[3].used,
-					  banks[3].rows, banks[3].columns,
-					  banks[3].size);
-	} else {
-		value2 = 0;
-	}
-
-	pci_write_cfg_long (0, 0, DIMM1_B2_SCR0, value1);
-	pci_write_cfg_long (0, 0, DIMM1_B3_SCR0, value2);
-
-	debug ("DIMM0_B2_SCR0 = 0x%08x\n", value1);
-	debug ("DIMM0_B3_SCR0 = 0x%08x\n", value2);
-
-	pci_write_cfg_long (0, 0, DIMM2_B4_SCR0, 0);
-	pci_write_cfg_long (0, 0, DIMM2_B5_SCR0, 0);
-	pci_write_cfg_long (0, 0, DIMM3_B6_SCR0, 0);
-	pci_write_cfg_long (0, 0, DIMM3_B7_SCR0, 0);
-
-	/* Determine timing */
-	select_cas (&banks[0], 0);
-	select_cas (&banks[2], 0);
-
-	/* FIXME: What about write recovery */
-	/*                    Auto refresh    Precharge */
-#if 0
-	reg32 = (0x3 << 13) | (0x7 << 10) | ((banks[0].trp - 2) << 8) |
-	/*    Write recovery  CAS Latency */
-		(0x1 << 6) | (banks[0].cas_used << 4) |
-	/*      RAS/CAS latency */
-		((banks[0].trcd - 1) << 0);
-
-	reg32 |= ((0x3 << 13) | (0x7 << 10) | ((banks[2].trp - 2) << 8) |
-		  (0x1 << 6) | (banks[2].cas_used << 4) |
-		  ((banks[2].trcd - 1) << 0)) << 16;
-#else
-	if (100000000 == gd->bus_clk)
-		reg32 = 0x71737173;
-	else
-		reg32 = 0x69736973;
-#endif
-	pci_write_cfg_long (0, 0, DIMM0_TCR0, reg32);
-	debug ("DIMM0_TCR0 = 0x%08x\n", reg32);
-
-	/* Write default in DIMM2/3 (not used on A1) */
-	pci_write_cfg_long (0, 0, DIMM2_TCR0, 0x7d737d73);
-
-
-	/* Determine buffered/unbuffered mode for each SIMM. Uses first bank as reference (second, if present, uses the same) */
-	reg32 = pci_read_cfg_long (0, 0, DRAM_GCR0);
-	reg32 &= 0xFF00FFFF;
-
-#if 0
-	if (banks[0].used && banks[0].registered)
-		reg32 |= 0x1 << 16;
-
-	if (banks[2].used && banks[2].registered)
-		reg32 |= 0x1 << 18;
-#else
-	if (banks[0].registered || banks[2].registered)
-		reg32 |= 0x55 << 16;
-#endif
-	pci_write_cfg_long (0, 0, DRAM_GCR0, reg32);
-	debug ("DRAM_GCR0 = 0x%08x\n", reg32);
-
-	/* Determine refresh */
-	refresh_clocks = 0xffffffff;
-	auto_refresh = 1;
-
-	for (i = 0; i < 4; i++) {
-		if (banks[i].used) {
-			if (banks[i].auto_refresh == 0)
-				auto_refresh = 0;
-			if (banks[i].refresh_time < refresh_clocks)
-				refresh_clocks = banks[i].refresh_time;
-		}
-	}
-
-
-#if 1
-	/*  It seems this is suggested by the ArticiaS data book */
-	if (100000000 == gd->bus_clk)
-		refresh_clocks = 1561;
-	else
-		refresh_clocks = 2083;
-#endif
-
-
-	debug ("Refresh set to %ld clocks, auto refresh %s\n",
-		   refresh_clocks, auto_refresh ? "on" : "off");
-
-	pci_write_cfg_long (0, 0, DRAM_REFRESH0,
-			(1 << 16) | (1 << 15) | (auto_refresh << 12) |
-			(refresh_clocks));
-	debug ("DRAM_REFRESH0 = 0x%08x\n",
-			(1 << 16) | (1 << 15) | (auto_refresh << 12) |
-			(refresh_clocks));
-
-/*     pci_write_cfg_long(0, 0, DRAM_REFRESH0,   0x00019400);  */
-
-	/* Set mode registers */
-	/* FIXME: For now, set same burst len for all modules. Dunno if that's necessary */
-	/* Find a common burst len */
-	burst_support = 0xff;
-
-	if (banks[0].used)
-		burst_support = banks[0].burst_len;
-	if (banks[1].used)
-		burst_support = banks[1].burst_len;
-	if (banks[2].used)
-		burst_support = banks[2].burst_len;
-	if (banks[3].used)
-		burst_support = banks[3].burst_len;
-
-	/*
-	   ** Mode register:
-	   ** Bits         Use
-	   ** 0-2          Burst len
-	   ** 3            Burst type (0 = sequential, 1 = interleave)
-	   ** 4-6          CAS latency
-	   ** 7-8          Operation mode (0 = default, all others invalid)
-	   ** 9            Write burst
-	   ** 10-11        Reserved
-	   **
-	   ** Mode register burst table:
-	   ** A2 A1 A0     lenght
-	   ** 0  0  0      1
-	   ** 0  0  1      2
-	   ** 0  1  0      4
-	   ** 0  1  1      8
-	   ** 1  0  0      invalid
-	   ** 1  0  1      invalid
-	   ** 1  1  0      invalid
-	   ** 1  1  1      page (only valid for non-interleaved)
-	 */
-
-	burst_len = burst_to_len (burst_support);
-	burst_len = 2;				/* FIXME */
-
-	if (banks[0].used) {
-		pci_write_cfg_word (0, 0, DRAM_PCR0,
-			0x8000 | burst_len | (banks[0].cas_used << 4));
-		debug ("Mode bank 0: 0x%08x\n",
-			0x8000 | burst_len | (banks[0].cas_used << 4));
-	} else {
-		/*  Seems to be needed to disable the bank */
-		pci_write_cfg_word (0, 0, DRAM_PCR0, 0x0000 | 0x032);
-	}
-
-	if (banks[1].used) {
-		pci_write_cfg_word (0, 0, DRAM_PCR0,
-			0x9000 | burst_len | (banks[1].cas_used << 4));
-		debug ("Mode bank 1: 0x%08x\n",
-			0x8000 | burst_len | (banks[1].cas_used << 4));
-	} else {
-		/*  Seems to be needed to disable the bank */
-		pci_write_cfg_word (0, 0, DRAM_PCR0, 0x1000 | 0x032);
-	}
-
-
-	if (banks[2].used) {
-		pci_write_cfg_word (0, 0, DRAM_PCR0,
-			0xa000 | burst_len | (banks[2].cas_used << 4));
-		debug ("Mode bank 2: 0x%08x\n",
-			0x8000 | burst_len | (banks[2].cas_used << 4));
-	} else {
-		/*  Seems to be needed to disable the bank */
-		pci_write_cfg_word (0, 0, DRAM_PCR0, 0x2000 | 0x032);
-	}
-
-
-	if (banks[3].used) {
-		pci_write_cfg_word (0, 0, DRAM_PCR0,
-			0xb000 | burst_len | (banks[3].cas_used << 4));
-		debug ("Mode bank 3: 0x%08x\n",
-			0x8000 | burst_len | (banks[3].cas_used << 4));
-	} else {
-		/*  Seems to be needed to disable the bank */
-		pci_write_cfg_word (0, 0, DRAM_PCR0, 0x3000 | 0x032);
-	}
-
-
-	pci_write_cfg_word (0, 0, 0xba, 0x00);
-
-	return total_ram;
-}
-
-extern int drv_isa_kbd_init (void);
-
-int last_stage_init (void)
-{
-	drv_isa_kbd_init ();
-	return 0;
-}
-
-int overwrite_console (void)
-{
-	return (0);
-}
-
-#define in_8 read_byte
-#define out_8 write_byte
-
-static __inline__ unsigned long get_msr (void)
-{
-	unsigned long msr;
-
-	asm volatile ("mfmsr %0":"=r" (msr):);
-
-	return msr;
-}
-
-static __inline__ void set_msr (unsigned long msr)
-{
-	asm volatile ("mtmsr %0"::"r" (msr));
-}
-
-int board_early_init_f (void)
-{
-	unsigned char c_value = 0;
-	unsigned long msr;
-
-	/* Basic init of PS/2 keyboard (needed for some reason)... */
-	/* Ripped from John's code */
-	while ((in_8 ((unsigned char *) 0xfe000064) & 0x02) != 0);
-	out_8 ((unsigned char *) 0xfe000064, 0xaa);
-	while ((in_8 ((unsigned char *) 0xfe000064) & 0x01) == 0);
-	c_value = in_8 ((unsigned char *) 0xfe000060);
-	while ((in_8 ((unsigned char *) 0xfe000064) & 0x02) != 0);
-	out_8 ((unsigned char *) 0xfe000064, 0xab);
-	while ((in_8 ((unsigned char *) 0xfe000064) & 0x01) == 0);
-	c_value = in_8 ((unsigned char *) 0xfe000060);
-	while ((in_8 ((unsigned char *) 0xfe000064) & 0x02) != 0);
-	out_8 ((unsigned char *) 0xfe000064, 0xae);
-/*     while ((in_8((unsigned char *)0xfe000064) & 0x01) == 0); */
-/*     c_value = in_8((unsigned char *)0xfe000060); */
-
-	/*  Enable FPU */
-	msr = get_msr ();
-	set_msr (msr | MSR_FP);
-
-	via_calibrate_bus_freq ();
-
-	return 0;
-}
diff --git a/board/MAI/AmigaOneG3SE/articiaS.h b/board/MAI/AmigaOneG3SE/articiaS.h
deleted file mode 100644
index ce20d03..0000000
--- a/board/MAI/AmigaOneG3SE/articiaS.h
+++ /dev/null
@@ -1,142 +0,0 @@
-#ifndef ARTICIAS_H
-#define ARTICIAS_H
-
-#include "short_types.h"
-#include <common.h>
-
-#define REG_GROUP       0xF0
-
-/* ArticiaS registers */
-#define GLOBALINFO0     0x50
-#define GLOBALINFO1     0x51
-#define GLOBALINFO2     0x52
-#define GLOBALINFO3     0x53
-#define GLOBALCTL0      0x54
-#define GLOBALCTL1      0x55
-#define NVRAMCTL        0x56
-#define PCI1ACR0        0x58
-#define PCI1ACR1        0x59
-#define PCI1ACR2        0x5a
-#define PCI1ACR3        0x5b
-#define HBUSACR0        0x5c
-#define HBUSACR1        0x5d
-#define HBUSACR2        0x5e
-#define HBUSACR3        0x5f
-#define HOSTINT0        0x68
-#define HOSTINT1        0x69
-#define HOSTINT2        0x6a
-#define HOSTINT3        0x6b
-#define HOSTRBCR        0x70
-#define XDBCR           0x74
-
-#define LBSBCR2         0xd2
-
-
-/* Memory controller */
-
-#define DIMM0_B0_SCR0   0x90
-#define DIMM0_B1_SCR0   0x94
-#define DIMM1_B2_SCR0   0x98
-#define DIMM1_B3_SCR0   0x9c
-#define DIMM2_B4_SCR0   0xa0
-#define DIMM2_B5_SCR0   0xa4
-#define DIMM3_B6_SCR0   0xa8
-#define DIMM3_B7_SCR0   0xac
-
-#define DIMM0_TCR0      0xb0
-#define DIMM1_TCR0      0xb2
-#define DIMM2_TCR0      0xb4
-#define DIMM3_TCR0      0xb6
-
-#define DRAM_REFRESH0   0xb8
-#define DRAM_GCR0       0xc0
-#define DRAM_PCR0       0xc6
-#define DRAM_ECC0       0xc4
-#define SRAM_CR         0xc8
-#define DRAM_RAS_CTL0   0xcc
-#define DRAM_RAS_CTL1   0xcd
-
-/* Bits for REG_GROUP */
-#define REG_GROUP_MULTI       (1<<1)
-#define REG_GROUP_SPECIAL     (1<<3)
-#define REG_GROUP_DIAG        (0x1<<4)
-#define REG_GROUP_POWER       (0x2<<4)
-
-
-#define GLOBALINFO0_BO        (1<<7)
-
-
-#define GLOBALINFO2_B1ARBITER (1<<6)
-
-
-#define HBUSACR0_CPUAPC       (1<<0)
-#define HBUSACR0_NUMREQ_2     (0<<1)
-#define HBUSACR0_NUMREQ_3     (1<<1)
-#define HBUSACR0_NUMREQ_4     (2<<1)
-#define HBUSACR0_NUMREQ_MASK  (7<<1)
-#define HBUSACR0_RAW          (1<<6)
-#define HBUSACR0_WAIT         (1<<7)
-#define HBUSACR0_RESERVED     (0x30)
-
-
-#define HBUSACR2_BURST        (1<<0)
-#define HBUSACR2_LAT          (1<<1)
-
-
-#define HBUSACR3_LMWC_SM      (1<<0)
-#define HBUSACR3_LMWC_PCI1    (1<<1)
-#define HBUSACR3_LMWC_PCI0    (1<<2)
-#define HBUSACR3_PMWC_PCI1    (1<<3)
-#define HBUSACR3_PMWC_PCI0    (1<<4)
-#define HBUSACR3_FKH          (1<<5)
-#define HBUSACR3_92H_EN       (1<<6)
-#define HBUSACR3_60H_64H_EN   (1<<7)
-
-
-#define HOSTRBCR_PREFETCH     (1<<4)
-
-
-#define XDBCR_HWTOXD          (1<<0)
-#define XDBCR_KBTOXD          (1<<1)
-#define XDBCR_RTCTOXD         (1<<2)
-#define XDBCR_SCALE_1_1       (0x0<<3)
-#define XDBCR_SCALE_2_2       (0x1<<3)
-#define XDBCR_SCALE_3_2       (0x2<<3)
-#define XDBCR_SCALE_4_4       (0x3<<3)
-#define XDBCR_SCALE_5_8       (0x4<<3)
-#define XDBCR_SCALE_6_8       (0x5<<3)
-#define XDBCR_SCALE_8_8       (0x6<<3)
-#define XDBCR_SCALE_0_16      (0x7<<3)
-#define XDBCR_XDPROM          (1<<7)
-
-
-#define LBSBCR2_1_RWAC        (1<<2)
-
-
-/* PCI controller */
-#define ARTICIAS_PCI_CFGADDR  0xfec00cf8
-#define ARTICIAS_PCI_CFGDATA  0xfee00cfc
-
-#define ARTICIAS_PCI_BUS       0x80000000
-#define ARTICIAS_PCI_MAXSIZE   0x7cffffff
-#define ARTICIAS_PCI_PHYS      0x80000000
-
-#define ARTICIAS_SYS_BUS       0x00000000
-#define ARTICIAS_SYS_MAXSIZE   0x7fffffff
-#define ARTICIAS_SYS_PHYS      0x00000000
-
-#define ARTICIAS_PCIIO_BUS     0x00800000
-#define ARTICIAS_PCIIO_MAXSIZE 0x003fffff
-#define ARTICIAS_PCIIO_PHYS    0xfe800000
-
-#define ARTICIAS_ISAIO_BUS     0x00002000
-#define ARTICIAS_ISAIO_MAXSIZE 0x0000d000
-#define ARTICIAS_ISAIO_PHYS    0xfe002000
-
-
-/* Prototypes */
-long articiaS_ram_init(void);
-void articiaS_pci_init(void);
-
-
-#endif
diff --git a/board/MAI/AmigaOneG3SE/articiaS_pci.c b/board/MAI/AmigaOneG3SE/articiaS_pci.c
deleted file mode 100644
index 371f67f..0000000
--- a/board/MAI/AmigaOneG3SE/articiaS_pci.c
+++ /dev/null
@@ -1,576 +0,0 @@
-/*
- * (C) Copyright 2002
- * Hyperion Entertainment, Hans-JoergF@hyperion-entertainment.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <pci.h>
-#include "memio.h"
-#include "articiaS.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#undef ARTICIA_PCI_DEBUG
-
-#ifdef  ARTICIA_PCI_DEBUG
-#define PRINTF(fmt,args...)     printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-struct pci_controller articiaS_hose;
-
-long irq_alloc(long wanted);
-
-static pci_dev_t pci_hose_find_class(struct pci_controller *hose, int bus, short find_class, int index);
-static int articiaS_init_vga(void);
-static void pci_cfgfunc_dummy(struct pci_controller *host, pci_dev_t dev, struct pci_config_table *table);
-unsigned char pci_irq_alloc(void);
-
-extern void via_cfgfunc_via686(struct pci_controller * host, pci_dev_t dev, struct pci_config_table *table);
-extern void via_cfgfunc_ide_init(struct pci_controller *host, pci_dev_t dev, struct pci_config_table *table);
-extern void via_init_irq_routing(uint8 []);
-extern void via_init_afterscan(void);
-
-#define cfgfunc_via686      1
-#define cfgfunc_dummy  2
-#define cfgfunc_ide_init    3
-
-static struct pci_config_table config_table[] =
-{
-    {
-	0x1106, PCI_ANY_ID, PCI_CLASS_BRIDGE_ISA, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
-	(void *)cfgfunc_via686, {0, 0, 0}
-    },
-    {
-	0x1106, PCI_ANY_ID, PCI_ANY_ID, 0,7,4,
-	(void *)cfgfunc_dummy, {0,0,0}
-    },
-    {
-	0x1106, 0x3068, PCI_ANY_ID, 0, 7, PCI_ANY_ID,
-	(void *)cfgfunc_dummy, {0,0,0}
-    },
-    {
-	0x1106, PCI_ANY_ID, PCI_ANY_ID, 0,7,1,
-	(void *)cfgfunc_ide_init, {0,0,0}
-    },
-    {
-	0,
-    }
-};
-
-
-void pci_cfgfunc_dummy(struct pci_controller *host, pci_dev_t dev, struct pci_config_table *table)
-{
-
-
-}
-
-unsigned long irq_penalties[16] =
-{
-    1000,    /* 0:timer */
-    1000,    /* 1:keyboard */
-    1000,    /* 2:cascade */
-    50,      /* 3:serial (COM2) */
-    50,      /* 4:serial (COM1) */
-    4,       /* 5:USB2 */
-    100,     /* 6:floppy */
-    3,       /* 7:parallel */
-    50,      /* 8:AC97/MC97 */
-    0,       /* 9: */
-    3,       /* 10:: */
-    0,       /* 11: */
-    3,       /* 12: USB1 */
-    0,       /* 13: */
-    100,     /* 14: ide0 */
-    100,     /* 15: ide1 */
-};
-
-
-/*
- * The following defines a hard-coded interrupt mapping for the
- * know devices on the board.
- * If a device isn't found here, assumed to be a device that's
- * plugged into a PCI or AGP slot
- * NOTE: This table is machine dependant.
- */
-
-struct pci_irq_fixup_table
-{
-    uint8   bus;             /* Bus number */
-    uint8   device;          /* Device number */
-    uint8   func;            /* Function number */
-    uint8   interrupt;       /* Interrupt to use (0xff to disable) */
-};
-
-struct pci_irq_fixup_table fixuptab [] =
-{
-    { 0, 0, 0, 0xff},        /* Articia S host bridge */
-    { 0, 1, 0, 0xff},        /* Articia S AGP bridge */
-/*    { 0, 6, 0, 0x05},        /###* 3COM ethernet */
-    { 0, 7, 0, 0xff},        /* VIA southbridge */
-    { 0, 7, 1, 0x0e},        /* IDE controller in legacy mode */
-/*    { 0, 7, 2, 0x05},        /###* First USB controller */
-/*    { 0, 7, 3, 0x0c},        /###* Second USB controller (shares interrupt with ethernet) */
-    { 0, 7, 4, 0xff},        /* ACPI Power Management */
-/*    { 0, 7, 5, 0x08},        /###* AC97 */
-/*    { 0, 7, 6, 0x08},        /###* MC97 */
-    { 0xff, 0xff, 0xff, 0xff}
-};
-
-
-/*
- * This table maps IRQ's to PCI interrupts
- */
-
-uint8 pci_intmap[4] = {0, 0, 0, 0};
-
-/*
- * Map PCI slots to interrupt routings
- * This table lists the device number assigned to a card inserted
- * into the slot, along with a permutation for the slot's IRQ routing.
- * NOTE: This table is machine dependant.
- */
-
-struct pci_slot_irq_routing
-{
-    uint8 bus;
-    uint8 device;
-
-    uint8 ints[4];
-};
-
-struct pci_slot_irq_routing amigaone_pci_routing[] =
-{
-    {0,  8,   {0, 1, 2, 3}},       /* Slot 1 (left of riser slot) */
-    {0,  9,   {1, 2, 3, 0}},       /* Slot 2 (middle slot) */
-    {0, 10,   {2, 3, 0, 1}},       /* Slot 3 (leftmost slot) */
-    {1,  0,   {1, 0, 2, 3}},       /* AGP slot (only IRQA and IRQB) */
-    {1,  1,   {1, 2, 3, 0}},       /* PCI slot on AGP bus */
-    {0,  6,   {3, 3, 3, 3}},       /* On board ethernet */
-    {0,  7,   {0, 1, 2, 3}},       /* Southbridge */
-    {0xff, 0, {0, 0, 0, 0}}
-};
-
-void articiaS_pci_irq_init(void)
-{
-    char *s;
-
-    s = getenv("pci_irqa");
-    if (s)
-	pci_intmap[0] = simple_strtoul (s, NULL, 10);
-    else
-	pci_intmap[0] = pci_irq_alloc();
-
-    s = getenv("pci_irqb");
-    if (s)
-	pci_intmap[1] = simple_strtoul (s, NULL, 10);
-    else
-	pci_intmap[1] = pci_irq_alloc();
-
-    s = getenv("pci_irqc");
-    if (s)
-	pci_intmap[2] = simple_strtoul (s, NULL, 10);
-    else
-	pci_intmap[2] = pci_irq_alloc();
-
-    s = getenv("pci_irqd");
-    if (s)
-	pci_intmap[3] = simple_strtoul (s, NULL, 10);
-    else
-	pci_intmap[3] = pci_irq_alloc();
-}
-
-
-unsigned char pci_irq_alloc(void)
-{
-    int i;
-    int interrupt = 10;
-    unsigned long min_penalty = 1000;
-
-    /* Search for the minimal penalty, favoring interrupts at the end */
-    for (i = 0; i < 16; i++)
-    {
-	if (irq_penalties[i] <= min_penalty)
-	{
-	    interrupt = i;
-	    min_penalty = irq_penalties[i];
-	}
-    }
-
-    PRINTF("pci_irq_alloc: Minimal penalty is %ld for %d\n", min_penalty, interrupt);
-
-    irq_penalties[interrupt]++;
-
-    return interrupt;
-}
-
-
-void articiaS_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
-{
-    int8 bus, device, func, pin, line;
-    int i;
-
-    bus = PCI_BUS(dev);
-    device = PCI_DEV(dev);
-    func = PCI_FUNC(dev);
-
-    PRINTF("Fixup irq of %d:%d.%d\n", bus, device, func);
-
-    /* Search for the device in the table */
-    for (i = 0; fixuptab[i].bus != 0xff; i++)
-    {
-	if (bus == fixuptab[i].bus && device == fixuptab[i].device && func == fixuptab[i].func)
-	{
-	    /* If the device needs an interrupt, write it */
-	    if (fixuptab[i].interrupt != 0xff)
-	    {
-		PRINTF("Assigning IRQ %d (fixed)\n", fixuptab[i].interrupt);
-		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, fixuptab[i].interrupt);
-	    }
-	    else
-	    {
-		/* Otherwise, see if it wants an interrupt, and disable it if needed */
-		pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
-		if (pin)
-		{
-		    PRINTF("Disabling IRQ\n");
-		    pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 0xff);
-		}
-	    }
-
-	    return;
-	}
-    }
-
-    /* If we get here, we have another PCI device in a slot... find the appropriate IRQ */
-
-    /* Find matching pin */
-    pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
-    pin--;
-
-    /* Search for it's map */
-    for (i = 0; amigaone_pci_routing[i].bus != 0xff; i++)
-    {
-	if (bus == amigaone_pci_routing[i].bus && device == amigaone_pci_routing[i].device)
-	{
-	    line = pci_intmap[amigaone_pci_routing[i].ints[pin]];
-	    PRINTF("Assigning IRQ %d (pin %d)\n", line, pin);
-	    pci_write_config_byte(dev, PCI_INTERRUPT_LINE, line);
-	    return;
-	}
-    }
-
-    PRINTF("Unkonwn PCI device found\n");
-}
-
-void articiaS_pci_init (void)
-{
-    int i;
-    char *s;
-
-    PRINTF("atriciaS_pci_init\n");
-
-    /* Why aren't these relocated?? */
-    for (i=0; config_table[i].config_device; i++)
-    {
-	switch((int)config_table[i].config_device)
-	{
-	case cfgfunc_via686:     config_table[i].config_device = via_cfgfunc_via686;      break;
-	case cfgfunc_dummy:      config_table[i].config_device = pci_cfgfunc_dummy;       break;
-	case cfgfunc_ide_init:   config_table[i].config_device = via_cfgfunc_ide_init;    break;
-	default: PRINTF("Error: Unknown constant\n");
-	}
-    }
-
-    articiaS_hose.first_busno = 0;
-    articiaS_hose.last_busno = 0xff;
-    articiaS_hose.config_table = config_table;
-    articiaS_hose.fixup_irq = articiaS_pci_fixup_irq;
-
-    articiaS_pci_irq_init();
-
-    /* System memory */
-    pci_set_region(articiaS_hose.regions + 0,
-		   ARTICIAS_SYS_BUS,
-		   ARTICIAS_SYS_PHYS,
-		   ARTICIAS_SYS_MAXSIZE,
-		   PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
-
-    /* PCI memory space */
-    pci_set_region(articiaS_hose.regions + 1,
-		   ARTICIAS_PCI_BUS,
-		   ARTICIAS_PCI_PHYS,
-		   ARTICIAS_PCI_MAXSIZE,
-		   PCI_REGION_MEM);
-
-    /* PCI io space */
-    pci_set_region(articiaS_hose.regions + 2,
-		   ARTICIAS_PCIIO_BUS,
-		   ARTICIAS_PCIIO_PHYS,
-		   ARTICIAS_PCIIO_MAXSIZE,
-		   PCI_REGION_IO);
-
-    /* PCI/ISA io space */
-    pci_set_region(articiaS_hose.regions + 3,
-		   ARTICIAS_ISAIO_BUS,
-		   ARTICIAS_ISAIO_PHYS,
-		   ARTICIAS_ISAIO_MAXSIZE,
-		   PCI_REGION_IO);
-
-
-    articiaS_hose.region_count = 4;
-
-    pci_setup_indirect(&articiaS_hose, ARTICIAS_PCI_CFGADDR, ARTICIAS_PCI_CFGDATA);
-    PRINTF("Registering articia hose...\n");
-    pci_register_hose(&articiaS_hose);
-    PRINTF("Enabling AGP...\n");
-    pci_write_config_byte(PCI_BDF(0,0,0), 0x58, 0x01);
-    PRINTF("Scanning bus...\n");
-    articiaS_hose.last_busno = pci_hose_scan(&articiaS_hose);
-
-    via_init_irq_routing(pci_intmap);
-
-    PRINTF("After-Scan results:\n");
-    PRINTF("Bus range: %d - %d\n", articiaS_hose.first_busno , articiaS_hose.last_busno);
-
-    via_init_afterscan();
-
-    pci_write_config_byte(PCI_BDF(0,1,0), PCI_INTERRUPT_LINE, 0xFF);
-
-    s = getenv("as_irq");
-    if (s)
-    {
-	pci_write_config_byte(PCI_BDF(0,0,0), PCI_INTERRUPT_LINE, simple_strtoul (s, NULL, 10));
-    }
-
-    s = getenv("x86_run_bios");
-    if (!s || (s && strcmp(s, "on")==0))
-    {
-	if (articiaS_init_vga() == -1)
-	{
-	    /* If the VGA didn't init and we have stdout set to VGA, reset to serial */
-/*	    s = getenv("stdout"); */
-/*	    if (s && strcmp(s, "vga") == 0) */
-/*	    { */
-/*		setenv("stdout", "serial"); */
-/*	    } */
-	}
-    }
-    pci_write_config_byte(PCI_BDF(0,1,0), PCI_INTERRUPT_LINE, 0xFF);
-
-}
-
-pci_dev_t pci_hose_find_class(struct pci_controller *hose, int bus, short find_class, int index)
-{
-    unsigned int sub_bus, found_multi=0;
-    unsigned short vendor, class;
-    unsigned char header_type;
-    pci_dev_t dev;
-    u8 c1, c2;
-
-    sub_bus = bus;
-
-    for (dev =  PCI_BDF(bus,0,0);
-	 dev <  PCI_BDF(bus,PCI_MAX_PCI_DEVICES-1,PCI_MAX_PCI_FUNCTIONS-1);
-	 dev += PCI_BDF(0,0,1))
-    {
-	if ( dev == PCI_BDF(hose->first_busno,0,0) )
-	    continue;
-
-	if (PCI_FUNC(dev) && !found_multi)
-	    continue;
-
-	pci_hose_read_config_byte(hose, dev, PCI_HEADER_TYPE, &header_type);
-
-	pci_hose_read_config_word(hose, dev, PCI_VENDOR_ID, &vendor);
-
-	if (vendor != 0xffff && vendor != 0x0000)
-	{
-
-	    if (!PCI_FUNC(dev))
-		found_multi = header_type & 0x80;
-	    pci_hose_read_config_byte(hose, dev, 0x0B, &c1);
-	    pci_hose_read_config_byte(hose, dev, 0x0A, &c2);
-	    class = c1<<8 | c2;
-	    /*printf("At %02x:%02x:%02x: class %x\n", */
-	    /*	   PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev), class); */
-	    if (class == find_class)
-	    {
-		if (index == 0)
-		    return dev;
-		else index--;
-	    }
-	}
-    }
-
-    return ~0;
-}
-
-
-/*
- * For a given bus number, find the bridge on this hose that provides this
- * bus number. The function scans for bridges and peeks config space offset
- * 0x19 (PCI_SECONDARY_BUS).
- */
-pci_dev_t pci_find_bridge_for_bus(struct pci_controller *hose, int busnr)
-{
-    pci_dev_t dev;
-    int bus;
-    unsigned int found_multi=0;
-    unsigned char header_type;
-    unsigned short vendor;
-    unsigned char secondary_bus;
-
-    if (hose == NULL) hose = &articiaS_hose;
-
-    if (busnr < hose->first_busno || busnr > hose->last_busno) return PCI_ANY_ID; /* Not in range */
-
-    /*
-     * The bridge must be on a lower bus number
-     */
-    for (bus = hose->first_busno; bus < busnr; bus++)
-    {
-	for (dev =  PCI_BDF(bus,0,0);
-	     dev <  PCI_BDF(bus,PCI_MAX_PCI_DEVICES-1,PCI_MAX_PCI_FUNCTIONS-1);
-	     dev += PCI_BDF(0,0,1))
-	{
-	    if ( dev == PCI_BDF(hose->first_busno,0,0) )
-		continue;
-
-	    if (PCI_FUNC(dev) && !found_multi)
-		continue;
-
-	    pci_hose_read_config_byte(hose, dev, PCI_HEADER_TYPE, &header_type);
-
-	    pci_hose_read_config_word(hose, dev, PCI_VENDOR_ID, &vendor);
-
-	    if (vendor != 0xffff && vendor != 0x0000)
-	    {
-
-		if (!PCI_FUNC(dev))
-		    found_multi = header_type & 0x80;
-		if (header_type == 1) /* Bridge device header */
-		{
-		    pci_hose_read_config_byte(hose, dev, PCI_SECONDARY_BUS, &secondary_bus);
-		    if ((int)secondary_bus == busnr) return dev;
-		}
-
-	    }
-	}
-    }
-    return PCI_ANY_ID;
-}
-
-static short classes[] =
-{
-    PCI_CLASS_DISPLAY_VGA,
-    PCI_CLASS_DISPLAY_XGA,
-    PCI_CLASS_DISPLAY_3D,
-    PCI_CLASS_DISPLAY_OTHER,
-    ~0
-};
-
-extern int execute_bios(pci_dev_t gr_dev, void *);
-
-pci_dev_t video_dev;
-
-int articiaS_init_vga (void)
-{
-    extern void shutdown_bios(void);
-    pci_dev_t dev = ~0;
-    int busnr = 0;
-    int classnr = 0;
-
-    video_dev = PCI_ANY_ID;
-
-    printf("VGA:   ");
-
-    PRINTF("Trying to initialize x86 VGA Card(s)\n");
-
-    while (dev == ~0)
-    {
-	PRINTF("Searching for class 0x%x on bus %d\n", classes[classnr], busnr);
-	/* Find the first of this class on this bus */
-	dev = pci_hose_find_class(&articiaS_hose, busnr, classes[classnr], 0);
-	if (dev != ~0)
-	{
-	    PRINTF("Found VGA Card at %02x:%02x:%02x\n", PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev));
-	    break;
-	}
-	busnr++;
-	if (busnr > articiaS_hose.last_busno)
-	{
-	    busnr = 0;
-	    classnr ++;
-	    if (classes[classnr] == ~0)
-	    {
-		printf("NOT PRESENT\n");
-		return -1;
-	    }
-	}
-    }
-
-    /*
-     * If we get here we have found the first graphics card.
-     * If the bus number is not 0, then it is probably behind a bridge, and the
-     * bridge needs to be told to forward VGA access.
-     */
-
-    if (PCI_BUS(dev) != 0)
-    {
-	pci_dev_t bridge;
-	PRINTF("Behind bridge, looking for bridge\n");
-	bridge = pci_find_bridge_for_bus(&articiaS_hose, PCI_BUS(dev));
-	if (dev != PCI_ANY_ID)
-	{
-	    unsigned char agp_control_0;
-	    PRINTF("Got the bridge at %02x:%02x:%02x\n",
-		   PCI_BUS(bridge), PCI_DEV(bridge), PCI_FUNC(bridge));
-	    pci_hose_read_config_byte(&articiaS_hose, bridge, 0x3E, &agp_control_0);
-	    agp_control_0 |= 0x18;
-	    pci_hose_write_config_byte(&articiaS_hose, bridge, 0x3E, agp_control_0);
-	    PRINTF("Configured for VGA forwarding\n");
-	}
-    }
-
-    /*
-     * Now try to run the bios
-     */
-    PRINTF("Trying to run bios now\n");
-    if (execute_bios(dev, gd->relocaddr))
-    {
-	printf("OK\n");
-	video_dev = dev;
-    }
-    else
-    {
-	printf("ERROR\n");
-    }
-
-    PRINTF("Done scanning.\n");
-
-    shutdown_bios();
-
-    if (dev == PCI_ANY_ID) return -1;
-    else return 0;
-
-}
diff --git a/board/MAI/AmigaOneG3SE/board_asm_init.S b/board/MAI/AmigaOneG3SE/board_asm_init.S
deleted file mode 100644
index 086b19c..0000000
--- a/board/MAI/AmigaOneG3SE/board_asm_init.S
+++ /dev/null
@@ -1,156 +0,0 @@
-#include	"macros.h"
-
-
-#define GLOBALINFO0	      0x50
-#define GLOBALINFO0_BO        (1<<7)
-#define GLOBALINFO2_B1ARBITER (1<<6)
-#define HBUSACR0              0x5c
-#define HBUSACR2_BURST        (1<<0)
-#define HBUSACR2_LAT          (1<<1)
-
-#define RECEIVER_HOLDING 0
-#define TRANSMITTER_HOLDING 0
-#define INTERRUPT_ENABLE 1
-#define INTERRUPT_STATUS 2
-#define FIFO_CONTROL 2
-#define LINE_CONTROL 3
-#define MODEM_CONTROL 4
-#define LINE_STATUS 5
-#define MODEM_STATUS 6
-#define SCRATCH_PAD 7
-
-#define DIVISOR_LATCH_LSB 0
-#define DIVISOR_LATCH_MSB 1
-#define PRESCALER_DIVISION 5
-
-#define UART(x) (0x3f8+(x))
-
-#define GLOBALINFO0           0x50
-#define GLOBALINFO0_BO        (1<<7)
-#define GLOBALINFO2_B1ARBITER (1<<6)
-#define HBUSACR0              0x5c
-#define HBUSACR2_BURST        (1<<0)
-#define HBUSACR2_LAT          (1<<1)
-
-#define SUPERIO_1               ((7 << 3) | (0))
-#define SUPERIO_2               ((7 << 3) | (1))
-
-	.globl	board_asm_init
-
-board_asm_init:
-	mflr	r29
-	/* Set 'Must-set' register */
-	li	r3, 0
-	li	r4, 0
-	li	r5, 0x5e
-	bl	pci_read_cfg_byte
-	ori	r3, r3, (1<<1)
-	xori	r6, r3, (1<<1)
-	li	r3, 0
-	bl	pci_write_cfg_byte
-
-	li	r3, 0
-	li	r5, 0x52
-	bl	pci_read_cfg_byte
-	ori	r6, r3, (1<<6)
-	li	r3, 0
-	bl	pci_write_cfg_byte
-
-	li	r3, 0
-	li	r4, 0x08
-	li	r5, 0xd2
-	bl	pci_read_cfg_byte
-	ori	r6, r3, (1<<2)
-	li	r3, 0
-	bl	pci_write_cfg_byte
-
-
-	/* Do PCI reset */
-/*	li	r3, 0
-	li	r4, 0x38
-	li	r5, 0x47
-	bl	pci_read_cfg_byte
-	ori	r6, r3, 0x01
-	li	r3, 0
-	li	r4, 0x38
-	li	r5, 0x47
-	bl	pci_write_cfg_byte*/
-
-
-	/* Enable NVRAM for environment */
-	li	r3, 0
-	li	r4, 0
-	li	r5, 0x56
-	li	r6, 0x0B
-	bl	pci_write_cfg_byte
-
-
-	/* Init Super-I/O chips */
-
-	siowb	0x40, 0x08
-	siowb	0x41, 0x01
-	siowb	0x45, 0x80
-	siowb	0x46, 0x60
-	siowb	0x47, 0x20
-	siowb	0x48, 0x01
-	siowb	0x4a, 0xc4
-	siowb	0x50, 0x0e
-	siowb	0x51, 0x76
-	siowb	0x52, 0x34
-	siowb	0x54, 0x00
-	siowb	0x55, 0x90
-	siowb	0x56, 0x99
-	siowb	0x57, 0x90
-	siowb	0x85, 0x01
-
-	/* Enable configuration mode for SuperIO */
-	li	r3, 0
-	li	r4, (7<<3)
-	li	r5, 0x85
-	bl	pci_read_cfg_byte
-	ori	r6, r3, 0x02
-	mr	r31, r6
-	li	r3,0
-	bl	pci_write_cfg_byte
-
-	/* COM1 as 3f8 */
-	outb	0x3f0, 0xe7
-	outb	0x3f1, 0xfe
-
-	/* COM2 as 2f8 */
-	outb	0x3f0, 0xe8
-	outb	0x3f1, 0xeb
-
-	/* Enable */
-	outb	0x3f0, 0xe2
-	inb	r3, 0x3f1
-	ori	r3, r3, 0x0c
-	outb	0x3f0, 0xe2
-	outbr	0x3f1, r3
-
-	/* Disable configuration mode */
-	li	r3, 0
-	li	r4, (7<<3)
-	li	r5, 0x85
-	mr	r6, r31
-	bl	pci_write_cfg_byte
-
-	/* Set line control */
-	outb	UART(LINE_CONTROL), 0x83
-	outb	UART(DIVISOR_LATCH_LSB), 0x0c
-	outb	UART(DIVISOR_LATCH_MSB), 0x00
-	outb	UART(LINE_CONTROL), 0x3
-
-	mtlr	r29
-	blr
-
-
-	.globl	new_reset
-	.globl	new_reset_end
-new_reset:
-	li	r0, 0x100
-	oris	r0, r0, 0xFFF0
-	mtlr	r0
-	blr
-
-new_reset_end:
diff --git a/board/MAI/AmigaOneG3SE/cmd_boota.c b/board/MAI/AmigaOneG3SE/cmd_boota.c
deleted file mode 100644
index 6b955d8..0000000
--- a/board/MAI/AmigaOneG3SE/cmd_boota.c
+++ /dev/null
@@ -1,128 +0,0 @@
-#include <common.h>
-#include <command.h>
-#include "../disk/part_amiga.h"
-#include <asm/cache.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#undef BOOTA_DEBUG
-
-#ifdef BOOTA_DEBUG
-#define PRINTF(fmt,args...)	printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-struct block_header {
-	u32 id;
-	u32 summed_longs;
-	s32 chk_sum;
-};
-
-extern block_dev_desc_t *ide_get_dev (int dev);
-extern struct bootcode_block *get_bootcode (block_dev_desc_t * dev_desc);
-extern int sum_block (struct block_header *header);
-
-struct bootcode_block bblk;
-
-int do_boota (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
-{
-	unsigned char *load_address = (unsigned char *) CONFIG_SYS_LOAD_ADDR;
-	unsigned char *base_address;
-	unsigned long offset;
-
-	unsigned long part_number = 0;
-	block_dev_desc_t *boot_disk;
-	char *s;
-	struct bootcode_block *boot_code;
-
-	/* Get parameters */
-
-	switch (argc) {
-	case 2:
-		load_address = (unsigned char *) simple_strtol (argv[1], NULL, 16);
-		part_number = 0;
-		break;
-	case 3:
-		load_address = (unsigned char *) simple_strtol (argv[1], NULL, 16);
-		part_number = simple_strtol (argv[2], NULL, 16);
-		break;
-	}
-
-	base_address = load_address;
-
-	PRINTF ("Loading boot code from disk %d to %p\n", part_number,
-			load_address);
-
-	/* Find the appropriate disk device */
-	boot_disk = ide_get_dev (part_number);
-	if (!boot_disk) {
-		PRINTF ("Unknown disk %d\n", part_number);
-		return 1;
-	}
-
-	/* Find the bootcode block */
-	boot_code = get_bootcode (boot_disk);
-	if (!boot_code) {
-		PRINTF ("Not a bootable disk %d\n", part_number);
-		return 1;
-	}
-
-	/* Only use the offset from the first block */
-	offset = boot_code->load_data[0];
-	memcpy (load_address, &boot_code->load_data[1], 122 * 4);
-	load_address += 122 * 4;
-
-	/* Setup for the loop */
-	bblk.next = boot_code->next;
-	boot_code = &bblk;
-
-	/* Scan the chain, and copy the loader succesively into the destination area */
-	while (0xffffffff != boot_code->next) {
-		PRINTF ("Loading block %d\n", boot_code->next);
-
-		/* Load block */
-		if (1 !=
-			boot_disk->block_read (boot_disk->dev, boot_code->next, 1,
-								   (ulong *) & bblk)) {
-			PRINTF ("Read error\n");
-			return 1;
-		}
-
-		/* check sum */
-		if (sum_block ((struct block_header *) (ulong *) & bblk) != 0) {
-			PRINTF ("Checksum error\n");
-			return 1;
-		}
-
-		/* Ok, concatenate it to the already loaded code */
-		memcpy (load_address, boot_code->load_data, 123 * 4);
-		load_address += 123 * 4;
-	}
-
-	printf ("Bootcode loaded to %p (size %d)\n", base_address,
-			load_address - base_address);
-	printf ("Entry point at %p\n", base_address + offset);
-
-	flush_cache (base_address, load_address - base_address);
-
-
-	s = getenv ("autostart");
-	if (s && strcmp (s, "yes") == 0) {
-		void (*boot) (bd_t *, char *, block_dev_desc_t *);
-		char *args;
-
-		boot = (void (*)(bd_t *, char *, block_dev_desc_t *)) (base_address + offset);
-		boot (gd->bd, getenv ("amiga_bootargs"), boot_disk);
-	}
-
-
-	return 0;
-}
-#if defined(CONFIG_AMIGAONEG3SE) && defined(CONFIG_CMD_BSP)
-U_BOOT_CMD(
-	boota,   3,      1,      do_boota,
-	"boot an Amiga kernel",
-	"address disk"
-);
-#endif /* _CMD_BOOTA_H */
diff --git a/board/MAI/AmigaOneG3SE/config.mk b/board/MAI/AmigaOneG3SE/config.mk
deleted file mode 100644
index 930a793..0000000
--- a/board/MAI/AmigaOneG3SE/config.mk
+++ /dev/null
@@ -1,32 +0,0 @@
-#
-# (C) Copyright 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-#
-# AmigaOneG3SE boards
-#
-
-X86EMU =  -I../bios_emulator/scitech/include -I../bios_emulator/scitech/src/x86emu
-
-TEXT_BASE = 0xfff00000
-
-PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -Wa,-mregnames -DEASTEREGG $(X86EMU) -Dprintk=printf #-DDEBUG
diff --git a/board/MAI/AmigaOneG3SE/enet.c b/board/MAI/AmigaOneG3SE/enet.c
deleted file mode 100644
index b9df55c..0000000
--- a/board/MAI/AmigaOneG3SE/enet.c
+++ /dev/null
@@ -1,840 +0,0 @@
-/*
- * (C) Copyright 2002
- * Adam Kowalczyk, ACK Software Controls Inc. akowalczyk@cogeco.ca
- *
- * Some portions taken from 3c59x.c Written 1996-1999 by Donald Becker.
- *
- * Outline of the program based on eepro100.c which is
- *
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <pci.h>
-
-#include "articiaS.h"
-#include "memio.h"
-
-/* 3Com Ethernet PCI definitions*/
-
-/* #define PCI_VENDOR_ID_3COM		0x10B7 */
-#define PCI_DEVICE_ID_3COM_3C905C	0x9200
-
-/* 3Com Commands, top 5 bits are command and bottom 11 bits are parameters */
-
-#define TotalReset		(0<<11)
-#define SelectWindow		(1<<11)
-#define StartCoax		(2<<11)
-#define RxDisable		(3<<11)
-#define RxEnable		(4<<11)
-#define RxReset			(5<<11)
-#define UpStall			(6<<11)
-#define UpUnstall		(6<<11)+1
-#define DownStall		(6<<11)+2
-#define DownUnstall		(6<<11)+3
-#define RxDiscard		(8<<11)
-#define TxEnable		(9<<11)
-#define TxDisable		(10<<11)
-#define TxReset			(11<<11)
-#define FakeIntr		(12<<11)
-#define AckIntr			(13<<11)
-#define SetIntrEnb		(14<<11)
-#define SetStatusEnb		(15<<11)
-#define SetRxFilter		(16<<11)
-#define SetRxThreshold		(17<<11)
-#define SetTxThreshold		(18<<11)
-#define SetTxStart		(19<<11)
-#define StartDMAUp		(20<<11)
-#define StartDMADown		(20<<11)+1
-#define StatsEnable		(21<<11)
-#define StatsDisable		(22<<11)
-#define StopCoax		(23<<11)
-#define SetFilterBit		(25<<11)
-
-/* The SetRxFilter command accepts the following classes */
-
-#define RxStation		1
-#define RxMulticast		2
-#define RxBroadcast		4
-#define RxProm			8
-
-/* 3Com status word defnitions */
-
-#define IntLatch		0x0001
-#define HostError		0x0002
-#define TxComplete		0x0004
-#define TxAvailable		0x0008
-#define RxComplete		0x0010
-#define RxEarly			0x0020
-#define IntReq			0x0040
-#define StatsFull		0x0080
-#define DMADone			(1<<8)
-#define DownComplete		(1<<9)
-#define UpComplete		(1<<10)
-#define DMAInProgress		(1<<11)		/* DMA controller is still busy.*/
-#define CmdInProgress		(1<<12)		/* EL3_CMD is still busy.*/
-
-/* Polling Registers */
-
-#define DnPoll			0x2d
-#define UpPoll			0x3d
-
-/* Register window 0 offets */
-
-#define Wn0EepromCmd		10		/* Window 0: EEPROM command register. */
-#define Wn0EepromData		12		/* Window 0: EEPROM results register. */
-#define IntrStatus		0x0E		/* Valid in all windows. */
-
-/* Register window 0 EEPROM bits */
-
-#define EEPROM_Read		0x80
-#define EEPROM_WRITE		0x40
-#define EEPROM_ERASE		0xC0
-#define EEPROM_EWENB		0x30		/* Enable erasing/writing for 10 msec. */
-#define EEPROM_EWDIS		0x00		/* Disable EWENB before 10 msec timeout. */
-
-/* EEPROM locations. */
-
-#define PhysAddr01		0
-#define PhysAddr23		1
-#define PhysAddr45		2
-#define ModelID			3
-#define EtherLink3ID		7
-#define IFXcvrIO		8
-#define IRQLine			9
-#define NodeAddr01		10
-#define NodeAddr23		11
-#define NodeAddr45		12
-#define DriverTune		13
-#define Checksum		15
-
-/* Register window 1 offsets, the window used in normal operation */
-
-#define TX_FIFO			0x10
-#define RX_FIFOa		0x10
-#define RxErrors		0x14
-#define RxStatus		0x18
-#define Timer			0x1A
-#define TxStatus		0x1B
-#define TxFree			0x1C		/* Remaining free bytes in Tx buffer. */
-
-/* Register Window 2 */
-
-#define Wn2_ResetOptions	12
-
-/* Register Window 3: MAC/config bits */
-
-#define Wn3_Config		0		/* Internal Configuration */
-#define Wn3_MAC_Ctrl		6
-#define Wn3_Options		8
-
-#define BFEXT(value, offset, bitcount)					\
-	((((unsigned long)(value)) >> (offset)) & ((1 << (bitcount)) - 1))
-
-#define BFINS(lhs, rhs, offset, bitcount)					\
-	(((lhs) & ~((((1 << (bitcount)) - 1)) << (offset))) |			\
-	(((rhs) & ((1 << (bitcount)) - 1)) << (offset)))
-
-#define RAM_SIZE(v)		BFEXT(v, 0, 3)
-#define RAM_WIDTH(v)		BFEXT(v, 3, 1)
-#define RAM_SPEED(v)		BFEXT(v, 4, 2)
-#define ROM_SIZE(v)		BFEXT(v, 6, 2)
-#define RAM_SPLIT(v)		BFEXT(v, 16, 2)
-#define XCVR(v)			BFEXT(v, 20, 4)
-#define AUTOSELECT(v)		BFEXT(v, 24, 1)
-
-/* Register Window 4: Xcvr/media bits */
-
-#define Wn4_FIFODiag		4
-#define Wn4_NetDiag		6
-#define Wn4_PhysicalMgmt	8
-#define Wn4_Media		10
-
-#define Media_SQE		0x0008		/* Enable SQE error counting for AUI. */
-#define Media_10TP		0x00C0		/* Enable link beat and jabber for 10baseT. */
-#define Media_Lnk		0x0080		/* Enable just link beat for 100TX/100FX. */
-#define Media_LnkBeat		0x0800
-
-/* Register Window 7: Bus Master control */
-
-#define Wn7_MasterAddr		0
-#define Wn7_MasterLen		6
-#define Wn7_MasterStatus	12
-
-/* Boomerang bus master control registers. */
-
-#define PktStatus		0x20
-#define DownListPtr		0x24
-#define FragAddr		0x28
-#define FragLen			0x2c
-#define TxFreeThreshold	0x2f
-#define UpPktStatus		0x30
-#define UpListPtr		0x38
-
-/* The Rx and Tx descriptor lists. */
-
-#define LAST_FRAG	0x80000000		/* Last Addr/Len pair in descriptor. */
-#define DN_COMPLETE	0x00010000		/* This packet has been downloaded */
-
-struct rx_desc_3com {
-	u32 next;				/* Last entry points to 0		*/
-	u32 status;				/* FSH -> Frame Start Header		*/
-	u32 addr;				/* Up to 63 addr/len pairs possible	*/
-	u32 length;				/* Set LAST_FRAG to indicate last pair	*/
-};
-
-/* Values for the Rx status entry. */
-
-#define RxDComplete		0x00008000
-#define RxDError		0x4000
-#define IPChksumErr		(1<<25)
-#define TCPChksumErr		(1<<26)
-#define UDPChksumErr		(1<<27)
-#define IPChksumValid		(1<<29)
-#define TCPChksumValid		(1<<30)
-#define UDPChksumValid		(1<<31)
-
-struct tx_desc_3com {
-	u32 next;				/* Last entry points to 0		*/
-	u32 status;				/* bits 0:12 length, others see below	*/
-	u32 addr;
-	u32 length;
-};
-
-/* Values for the Tx status entry. */
-
-#define CRCDisable		0x2000
-#define TxDComplete		0x8000
-#define AddIPChksum		0x02000000
-#define AddTCPChksum		0x04000000
-#define AddUDPChksum		0x08000000
-#define TxIntrUploaded		0x80000000	/* IRQ when in FIFO, but maybe not sent. */
-
-/* XCVR Types */
-
-#define XCVR_10baseT		0
-#define XCVR_AUI		1
-#define XCVR_10baseTOnly	2
-#define XCVR_10base2		3
-#define XCVR_100baseTx		4
-#define XCVR_100baseFx		5
-#define XCVR_MII		6
-#define XCVR_NWAY		8
-#define XCVR_ExtMII		9
-#define XCVR_Default		10		/* I don't think this is correct -> should have been 0x10 if Auto Negotiate */
-
-struct descriptor {				/* A generic descriptor. */
-	u32 next;				/* Last entry points to 0		*/
-	u32 status;				/* FSH -> Frame Start Header		*/
-	u32 addr;				/* Up to 63 addr/len pairs possible	*/
-	u32 length;				/* Set LAST_FRAG to indicate last pair	*/
-};
-
-/* Misc. definitions */
-
-#define NUM_RX_DESC		PKTBUFSRX * 10
-#define NUM_TX_DESC		1		/* Number of TX descriptors   */
-
-#define TOUT_LOOP		1000000
-
-#define ETH_ALEN		6
-
-#define EL3WINDOW(dev, win_num) ETH_OUTW(dev, SelectWindow + (win_num), EL3_CMD)
-#define EL3_CMD 0x0e
-#define EL3_STATUS 0x0e
-
-
-#undef ETH_DEBUG
-
-#ifdef ETH_DEBUG
-#define PRINTF(fmt,args...)	printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-
-static struct rx_desc_3com *rx_ring;		/* RX descriptor ring		*/
-static struct tx_desc_3com *tx_ring;		/* TX descriptor ring		*/
-static u8 rx_buffer[NUM_RX_DESC][PKTSIZE_ALIGN];/* storage for the incoming messages	*/
-static int rx_next = 0;				/* RX descriptor ring pointer		*/
-static int tx_next = 0;				/* TX descriptor ring pointer		*/
-static int tx_threshold;
-
-static void  init_rx_ring(struct eth_device* dev);
-static void  purge_tx_ring(struct eth_device* dev);
-
-static void  read_hw_addr(struct eth_device* dev, bd_t * bis);
-
-static int eth_3com_init(struct eth_device* dev, bd_t *bis);
-static int eth_3com_send(struct eth_device* dev, volatile void *packet, int length);
-static int eth_3com_recv(struct eth_device* dev);
-static void eth_3com_halt(struct eth_device* dev);
-
-#define io_to_phys(a)	pci_io_to_phys((pci_dev_t)dev->priv, a)
-#define phys_to_io(a)	pci_phys_to_io((pci_dev_t)dev->priv, a)
-#define mem_to_phys(a)	pci_mem_to_phys((pci_dev_t)dev->priv, a)
-#define phys_to_mem(a)	pci_phys_to_mem((pci_dev_t)dev->priv, a)
-
-static inline int ETH_INL(struct eth_device* dev, u_long addr)
-{
-	__asm__ volatile ("eieio");
-	return le32_to_cpu(*(volatile u32 *)io_to_phys(addr + dev->iobase));
-}
-
-static inline int ETH_INW(struct eth_device* dev, u_long addr)
-{
-	__asm__ volatile ("eieio");
-	return le16_to_cpu(*(volatile u16 *)io_to_phys(addr + dev->iobase));
-}
-
-static inline int ETH_INB(struct eth_device* dev, u_long addr)
-{
-	__asm__ volatile ("eieio");
-	return *(volatile u8 *)io_to_phys(addr + dev->iobase);
-}
-
-static inline void ETH_OUTB(struct eth_device* dev, int command, u_long addr)
-{
-	*(volatile u8 *)io_to_phys(addr + dev->iobase) = command;
-	__asm__ volatile ("eieio");
-}
-
-static inline void ETH_OUTW(struct eth_device* dev, int command, u_long addr)
-{
-	*(volatile u16 *)io_to_phys(addr + dev->iobase) = cpu_to_le16(command);
-	__asm__ volatile ("eieio");
-}
-
-static inline void ETH_OUTL(struct eth_device* dev, int command, u_long addr)
-{
-	*(volatile u32 *)io_to_phys(addr + dev->iobase) = cpu_to_le32(command);
-	__asm__ volatile ("eieio");
-}
-
-static inline int ETH_STATUS(struct eth_device* dev)
-{
-	__asm__ volatile ("eieio");
-	return le16_to_cpu(*(volatile u16 *)io_to_phys(EL3_STATUS + dev->iobase));
-}
-
-static inline void ETH_CMD(struct eth_device* dev, int command)
-{
-	*(volatile u16 *)io_to_phys(EL3_CMD + dev->iobase) = cpu_to_le16(command);
-	__asm__ volatile ("eieio");
-}
-
-/* Command register is always in the same spot in all the register windows */
-/* This function issues a command and waits for it so complete by checking the CmdInProgress bit */
-
-static int issue_and_wait(struct eth_device* dev, int command)
-{
-
-	int i, status;
-
-	ETH_CMD(dev, command);
-	for (i = 0; i < 2000; i++) {
-		status = ETH_STATUS(dev);
-		/*printf ("Issue: status 0x%4x.\n", status); */
-		if (!(status & CmdInProgress))
-			return 1;
-	}
-
-	/* OK, that didn't work.  Do it the slow way.  One second */
-	for (i = 0; i < 100000; i++) {
-		status = ETH_STATUS(dev);
-		/*printf ("Issue: status 0x%4x.\n", status); */
-			return 1;
-		udelay(10);
-	}
-	PRINTF("Ethernet command: 0x%4x did not complete! Status: 0x%4x\n", command, ETH_STATUS(dev) );
-	return 0;
-}
-
-/* Determine network media type and set up 3com accordingly	      */
-/* I think I'm going to start with something known first like 10baseT */
-
-static int auto_negotiate (struct eth_device *dev)
-{
-	int i;
-
-	EL3WINDOW (dev, 1);
-
-	/* Wait for Auto negotiation to complete */
-	for (i = 0; i <= 1000; i++) {
-		if (ETH_INW (dev, 2) & 0x04)
-			break;
-		udelay (100);
-
-		if (i == 1000) {
-			PRINTF ("Error: Auto negotiation failed\n");
-			return 0;
-		}
-	}
-
-
-	return 1;
-}
-
-void eth_interrupt (struct eth_device *dev)
-{
-	u16 status = ETH_STATUS (dev);
-
-	printf ("eth0: status = 0x%04x\n", status);
-
-	if (!(status & IntLatch))
-		return;
-
-	if (status & (1 << 6)) {
-		ETH_CMD (dev, AckIntr | (1 << 6));
-		printf ("Acknowledged Interrupt command\n");
-	}
-
-	if (status & DownComplete) {
-		ETH_CMD (dev, AckIntr | DownComplete);
-		printf ("Acknowledged DownComplete\n");
-	}
-
-	if (status & UpComplete) {
-		ETH_CMD (dev, AckIntr | UpComplete);
-		printf ("Acknowledged UpComplete\n");
-	}
-
-	ETH_CMD (dev, AckIntr | IntLatch);
-	printf ("Acknowledged IntLatch\n");
-}
-
-int eth_3com_initialize (bd_t * bis)
-{
-	u32 eth_iobase = 0, status;
-	int card_number = 0, ret;
-	struct eth_device *dev;
-	pci_dev_t devno;
-	char *s;
-
-	s = getenv ("3com_base");
-
-	/* Find ethernet controller on the PCI bus */
-
-	if ((devno =
-	     pci_find_device (PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C905C,
-			      0)) < 0) {
-		PRINTF ("Error: Cannot find the ethernet device on the PCI bus\n");
-		goto Done;
-	}
-
-	if (s) {
-		unsigned long base = atoi (s);
-
-		pci_write_config_dword (devno, PCI_BASE_ADDRESS_0,
-					base | 0x01);
-	}
-
-	ret = pci_read_config_dword (devno, PCI_BASE_ADDRESS_0, &eth_iobase);
-	eth_iobase &= ~0xf;
-
-	PRINTF ("eth: 3Com Found at Address: 0x%x\n", eth_iobase);
-
-	pci_write_config_dword (devno, PCI_COMMAND,
-				PCI_COMMAND_IO | PCI_COMMAND_MEMORY |
-				PCI_COMMAND_MASTER);
-
-	/* Check if I/O accesses and Bus Mastering are enabled */
-
-	ret = pci_read_config_dword (devno, PCI_COMMAND, &status);
-
-	if (!(status & PCI_COMMAND_IO)) {
-		printf ("Error: Cannot enable IO access.\n");
-		goto Done;
-	}
-
-	if (!(status & PCI_COMMAND_MEMORY)) {
-		printf ("Error: Cannot enable MEMORY access.\n");
-		goto Done;
-	}
-
-	if (!(status & PCI_COMMAND_MASTER)) {
-		printf ("Error: Cannot enable Bus Mastering.\n");
-		goto Done;
-	}
-
-	dev = (struct eth_device *) malloc (sizeof (*dev));	/*struct eth_device)); */
-
-	sprintf (dev->name, "3Com 3c920c#%d", card_number);
-	dev->iobase = eth_iobase;
-	dev->priv = (void *) devno;
-	dev->init = eth_3com_init;
-	dev->halt = eth_3com_halt;
-	dev->send = eth_3com_send;
-	dev->recv = eth_3com_recv;
-
-	eth_register (dev);
-
-/*	{ */
-/*	    char interrupt; */
-/*	    devno = pci_find_device(PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C905C, 0); */
-/*	    pci_read_config_byte(devno, PCI_INTERRUPT_LINE, &interrupt); */
-
-/*	    printf("Installing eth0 interrupt handler to %d\n", interrupt); */
-/*	    irq_install_handler(interrupt, eth_interrupt, dev); */
-/*	} */
-
-	card_number++;
-
-	/* Set the latency timer for value */
-	s = getenv ("3com_latency");
-	if (s) {
-		ret = pci_write_config_byte (devno, PCI_LATENCY_TIMER,
-					     (unsigned char) atoi (s));
-	} else
-		ret = pci_write_config_byte (devno, PCI_LATENCY_TIMER, 0x0a);
-
-	read_hw_addr (dev, bis);	/* get the MAC address from Window 2 */
-
-	/* Reset the ethernet controller */
-
-	PRINTF ("Issuing reset command....\n");
-	if (!issue_and_wait (dev, TotalReset)) {
-		printf ("Error: Cannot reset ethernet controller.\n");
-		goto Done;
-	} else
-		PRINTF ("Ethernet controller reset.\n");
-
-	/* allocate memory for rx and tx rings */
-
-	if (!(rx_ring = memalign (sizeof (struct rx_desc_3com) * NUM_RX_DESC, 16))) {
-		PRINTF ("Cannot allocate memory for RX_RING.....\n");
-		goto Done;
-	}
-
-	if (!(tx_ring = memalign (sizeof (struct tx_desc_3com) * NUM_TX_DESC, 16))) {
-		PRINTF ("Cannot allocate memory for TX_RING.....\n");
-		goto Done;
-	}
-
-Done:
-	return status;
-}
-
-
-static int eth_3com_init (struct eth_device *dev, bd_t * bis)
-{
-	int i, status = 0;
-	int tx_cur, loop;
-	u16 status_enable, intr_enable;
-	struct descriptor *ias_cmd;
-
-	/* Determine what type of network the machine is connected to   */
-	/* presently drops the connect to 10Mbps                        */
-
-	if (!auto_negotiate (dev)) {
-		printf ("Error: Cannot determine network media.\n");
-		goto Done;
-	}
-
-	issue_and_wait (dev, TxReset);
-	issue_and_wait (dev, RxReset | 0x04);
-
-	/* Switch to register set 7 for normal use. */
-	EL3WINDOW (dev, 7);
-
-	/* Initialize Rx and Tx rings */
-
-	init_rx_ring (dev);
-	purge_tx_ring (dev);
-
-	ETH_CMD (dev, SetRxFilter | RxStation | RxBroadcast | RxProm);
-
-	issue_and_wait (dev, SetTxStart | 0x07ff);
-
-	/* Below sets which indication bits to be seen. */
-
-	status_enable =
-		SetStatusEnb | HostError | DownComplete | UpComplete | (1 <<
-									6);
-	ETH_CMD (dev, status_enable);
-
-	/* Below sets no bits are to cause an interrupt since this is just polling */
-
-	intr_enable = SetIntrEnb;
-/*	intr_enable = SetIntrEnb | (1<<9) | (1<<10) | (1<<6); */
-	ETH_CMD (dev, intr_enable);
-	ETH_OUTB (dev, 127, UpPoll);
-
-	/* Ack all pending events, and set active indicator mask */
-
-	ETH_CMD (dev, AckIntr | IntLatch | TxAvailable | RxEarly | IntReq);
-	ETH_CMD (dev, intr_enable);
-
-	/* Tell the adapter where the RX ring is located */
-
-	issue_and_wait (dev, UpStall);	/* Stall and set the UplistPtr          */
-	ETH_OUTL (dev, (u32) & rx_ring[rx_next], UpListPtr);
-	ETH_CMD (dev, RxEnable);	/* Enable the receiver.         */
-	issue_and_wait (dev, UpUnstall);
-
-	/* Send the Individual Address Setup frame */
-
-	tx_cur = tx_next;
-	tx_next = ((tx_next + 1) % NUM_TX_DESC);
-
-	ias_cmd = (struct descriptor *) &tx_ring[tx_cur];
-	ias_cmd->status = cpu_to_le32 (1 << 31);	/* set DnIndicate bit.                  */
-	ias_cmd->next = 0;
-	ias_cmd->addr = cpu_to_le32 ((u32) dev->enetaddr);
-	ias_cmd->length = cpu_to_le32 (6 | LAST_FRAG);
-
-	/* Tell the adapter where the TX ring is located */
-
-	ETH_CMD (dev, TxEnable);	/* Enable transmitter.                  */
-	issue_and_wait (dev, DownStall);	/* Stall and set the DownListPtr.       */
-	ETH_OUTL (dev, (u32) & tx_ring[tx_cur], DownListPtr);
-	issue_and_wait (dev, DownUnstall);
-	for (i = 0; !(ETH_STATUS (dev) & DownComplete); i++) {
-		if (i >= TOUT_LOOP) {
-			PRINTF ("TX Ring status (Init):	0x%4x\n",
-				le32_to_cpu (tx_ring[tx_cur].status));
-			PRINTF ("ETH_STATUS: 0x%x\n", ETH_STATUS (dev));
-			goto Done;
-		}
-	}
-	if (ETH_STATUS (dev) & DownComplete) {	/* If DownLoad Complete ACK the bit       */
-		ETH_CMD (dev, AckIntr | DownComplete);	/* acknowledge the indication bit       */
-		issue_and_wait (dev, DownStall);	/* stall and clear DownListPtr          */
-		ETH_OUTL (dev, 0, DownListPtr);
-		issue_and_wait (dev, DownUnstall);
-	}
-	status = 1;
-Done:
-	return status;
-}
-
-int eth_3com_send (struct eth_device *dev, volatile void *packet, int length)
-{
-	int i, status = 0;
-	int tx_cur;
-
-	if (length <= 0) {
-		PRINTF ("eth: bad packet size: %d\n", length);
-		goto Done;
-	}
-
-	tx_cur = tx_next;
-	tx_next = (tx_next + 1) % NUM_TX_DESC;
-
-	tx_ring[tx_cur].status = cpu_to_le32 (1 << 31);	/* set DnIndicate bit                   */
-	tx_ring[tx_cur].next = 0;
-	tx_ring[tx_cur].addr = cpu_to_le32 (((u32) packet));
-	tx_ring[tx_cur].length = cpu_to_le32 (length | LAST_FRAG);
-
-	/* Send the packet */
-
-	issue_and_wait (dev, DownStall);	/* stall and set the DownListPtr        */
-	ETH_OUTL (dev, (u32) & tx_ring[tx_cur], DownListPtr);
-	issue_and_wait (dev, DownUnstall);
-
-	for (i = 0; !(ETH_STATUS (dev) & DownComplete); i++) {
-		if (i >= TOUT_LOOP) {
-			PRINTF ("TX Ring status (send): 0x%4x\n",
-				le32_to_cpu (tx_ring[tx_cur].status));
-			goto Done;
-		}
-	}
-	if (ETH_STATUS (dev) & DownComplete) {	/* If DownLoad Complete ACK the bit       */
-		ETH_CMD (dev, AckIntr | DownComplete);	/* acknowledge the indication bit       */
-		issue_and_wait (dev, DownStall);	/* stall and clear DownListPtr          */
-		ETH_OUTL (dev, 0, DownListPtr);
-		issue_and_wait (dev, DownUnstall);
-	}
-	status = 1;
-Done:
-	return status;
-}
-
-void PrintPacket (uchar * packet, int length)
-{
-	int loop;
-	uchar *ptr;
-
-	printf ("Printing packet of length %x.\n\n", length);
-	ptr = packet;
-	for (loop = 1; loop <= length; loop++) {
-		printf ("%2x ", *ptr++);
-		if ((loop % 40) == 0)
-			printf ("\n");
-	}
-}
-
-int eth_3com_recv (struct eth_device *dev)
-{
-	u16 stat = 0;
-	u32 status;
-	int rx_prev, length = 0;
-
-	while (!(ETH_STATUS (dev) & UpComplete))	/* wait on receipt of packet        */
-		;
-
-	status = le32_to_cpu (rx_ring[rx_next].status);	/* packet status                */
-
-	while (status & (1 << 15)) {
-		/* A packet has been received */
-
-		if (status & (1 << 15)) {
-			/* A valid frame received  */
-
-			length = le32_to_cpu (rx_ring[rx_next].status) & 0x1fff;	/* length is in bits 0 - 12     */
-
-			/* Pass the packet up to the protocol layers */
-
-			NetReceive ((uchar *)
-				    le32_to_cpu (rx_ring[rx_next].addr),
-				    length);
-			rx_ring[rx_next].status = 0;	/* clear the status word        */
-			ETH_CMD (dev, AckIntr | UpComplete);
-			issue_and_wait (dev, UpUnstall);
-		} else if (stat & HostError) {
-			/* There was an error */
-
-			printf ("Rx error status:  0x%4x\n", stat);
-			init_rx_ring (dev);
-			goto Done;
-		}
-
-		rx_prev = rx_next;
-		rx_next = (rx_next + 1) % NUM_RX_DESC;
-		stat = ETH_STATUS (dev);	/* register status      */
-		status = le32_to_cpu (rx_ring[rx_next].status);	/* packet status        */
-	}
-Done:
-	return length;
-}
-
-void eth_3com_halt (struct eth_device *dev)
-{
-	if (!(dev->iobase)) {
-		goto Done;
-	}
-
-	issue_and_wait (dev, DownStall);	/* shut down transmit and receive */
-	issue_and_wait (dev, UpStall);
-	issue_and_wait (dev, RxDisable);
-	issue_and_wait (dev, TxDisable);
-
-/*	free(tx_ring);				/###* release memory allocated to the DPD and UPD rings */
-/*	free(rx_ring); */
-
-Done:
-	return;
-}
-
-static void init_rx_ring (struct eth_device *dev)
-{
-	int i;
-
-	PRINTF ("Initializing rx_ring. rx_buffer = %p\n", rx_buffer);
-	issue_and_wait (dev, UpStall);
-
-	for (i = 0; i < NUM_RX_DESC; i++) {
-		rx_ring[i].next =
-			cpu_to_le32 (((u32) &
-				      rx_ring[(i + 1) % NUM_RX_DESC]));
-		rx_ring[i].status = 0;
-		rx_ring[i].addr = cpu_to_le32 (((u32) & rx_buffer[i][0]));
-		rx_ring[i].length = cpu_to_le32 (PKTSIZE_ALIGN | LAST_FRAG);
-	}
-	rx_next = 0;
-}
-
-static void purge_tx_ring (struct eth_device *dev)
-{
-	int i;
-
-	PRINTF ("Purging tx_ring.\n");
-
-	tx_next = 0;
-
-	for (i = 0; i < NUM_TX_DESC; i++) {
-		tx_ring[i].next = 0;
-		tx_ring[i].status = 0;
-		tx_ring[i].addr = 0;
-		tx_ring[i].length = 0;
-	}
-}
-
-static void read_hw_addr (struct eth_device *dev, bd_t * bis)
-{
-	u8 hw_addr[ETH_ALEN];
-	unsigned int eeprom[0x40];
-	unsigned int checksum = 0;
-	int i, j, timer;
-
-	/* First, try the env ... if that works, we're all done! */
-	if (eth_getenv_enetaddr("ethaddr", hw_addr))
-		goto Done;
-
-	/* Read the station address from the EEPROM. */
-
-	EL3WINDOW (dev, 0);
-	for (i = 0; i < 0x40; i++) {
-		ETH_OUTW (dev, EEPROM_Read + i, Wn0EepromCmd);
-		/* Pause for at least 162 us. for the read to take place. */
-		for (timer = 10; timer >= 0; timer--) {
-			udelay (162);
-			if ((ETH_INW (dev, Wn0EepromCmd) & 0x8000) == 0)
-				break;
-		}
-		eeprom[i] = ETH_INW (dev, Wn0EepromData);
-	}
-
-	/* Checksum calculation.  I'm not sure about this part and there seems to be a bug on the 3com side of things */
-
-	for (i = 0; i < 0x21; i++)
-		checksum ^= eeprom[i];
-	checksum = (checksum ^ (checksum >> 8)) & 0xff;
-
-	if (checksum != 0xbb)
-		printf (" *** INVALID EEPROM CHECKSUM %4.4x *** \n",
-			checksum);
-
-	for (i = 0, j = 0; i < 3; i++) {
-		hw_addr[j++] = (u8) ((eeprom[i + 10] >> 8) & 0xff);
-		hw_addr[j++] = (u8) (eeprom[i + 10] & 0xff);
-	}
-
-	/*  MAC Address is in window 2, write value from EEPROM to window 2 */
-
-	EL3WINDOW (dev, 2);
-	for (i = 0; i < 6; i++)
-		ETH_OUTB (dev, hw_addr[i], i);
-
-	for (j = 0; j < ETH_ALEN; j += 2) {
-		hw_addr[j] = (u8) (ETH_INW (dev, j) & 0xff);
-		hw_addr[j + 1] = (u8) ((ETH_INW (dev, j) >> 8) & 0xff);
-	}
-
-	/* Save the result in the environment */
-	eth_setenv_enetaddr("ethaddr", hw_addr);
-
-Done:
-	memcpy(dev->enetaddr, hw_addr, 6);
-	return;
-}
diff --git a/board/MAI/AmigaOneG3SE/flash.c b/board/MAI/AmigaOneG3SE/flash.c
deleted file mode 100644
index a96d5ba..0000000
--- a/board/MAI/AmigaOneG3SE/flash.c
+++ /dev/null
@@ -1,35 +0,0 @@
-#include <common.h>
-#include <flash.h>
-
-flash_info_t    flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-
-unsigned long flash_init(void)
-{
-    int i;
-
-    for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
-    {
-	flash_info[i].flash_id = FLASH_UNKNOWN;
-	flash_info[i].sector_count = 0;
-	flash_info[i].size = 0;
-    }
-
-
-    return 1;
-}
-
-int flash_erase(flash_info_t *info, int s_first, int s_last)
-{
-    return 1;
-}
-
-void flash_print_info(flash_info_t *info)
-{
-    printf("No flashrom installed\n");
-}
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-    return 0;
-}
diff --git a/board/MAI/AmigaOneG3SE/flash_new.c b/board/MAI/AmigaOneG3SE/flash_new.c
deleted file mode 100644
index 9beb048..0000000
--- a/board/MAI/AmigaOneG3SE/flash_new.c
+++ /dev/null
@@ -1,651 +0,0 @@
-/*
- * (C) Copyright 2001
- * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
- *
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <flash.h>
-#include <asm/io.h>
-#include "memio.h"
-
-/*---------------------------------------------------------------------*/
-#undef DEBUG_FLASH
-
-#ifdef DEBUG_FLASH
-#define DEBUGF(fmt,args...) printf(fmt ,##args)
-#else
-#define DEBUGF(fmt,args...)
-#endif
-/*---------------------------------------------------------------------*/
-
-flash_info_t	flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-static ulong flash_get_size (ulong addr, flash_info_t *info);
-static int flash_get_offsets (ulong base, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static void flash_reset (ulong addr);
-
-int flash_xd_nest;
-
-static void flash_to_xd(void)
-{
-    unsigned char x;
-
-    flash_xd_nest ++;
-
-    if (flash_xd_nest == 1)
-    {
-	DEBUGF("Flash on XD\n");
-	x = pci_read_cfg_byte(0, 0, 0x74);
-	pci_write_cfg_byte(0, 0, 0x74, x|1);
-    }
-}
-
-static void flash_to_mem(void)
-{
-    unsigned char x;
-
-    flash_xd_nest --;
-
-    if (flash_xd_nest == 0)
-    {
-	DEBUGF("Flash on memory bus\n");
-	x = pci_read_cfg_byte(0, 0, 0x74);
-	pci_write_cfg_byte(0, 0, 0x74, x&0xFE);
-    }
-}
-
-unsigned long flash_init_old(void)
-{
-    int i;
-
-    for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
-    {
-	flash_info[i].flash_id = FLASH_UNKNOWN;
-	flash_info[i].sector_count = 0;
-	flash_info[i].size = 0;
-    }
-
-
-    return 1;
-}
-
-unsigned long flash_init (void)
-{
-	unsigned int i;
-	unsigned long flash_size = 0;
-
-	flash_xd_nest = 0;
-
-	flash_to_xd();
-
-	/* Init: no FLASHes known */
-	for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-		flash_info[i].sector_count = 0;
-		flash_info[i].size = 0;
-	}
-
-	DEBUGF("\n## Get flash size @ 0x%08x\n", CONFIG_SYS_FLASH_BASE);
-
-	flash_size = flash_get_size (CONFIG_SYS_FLASH_BASE, flash_info);
-
-	DEBUGF("## Flash bank size: %08lx\n", flash_size);
-
-	if (flash_size) {
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE && \
-    CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_MAX_SIZE
-		/* monitor protection ON by default */
-		flash_protect(FLAG_PROTECT_SET,
-			      CONFIG_SYS_MONITOR_BASE,
-			      CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
-			      &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-		/* ENV protection ON by default */
-		flash_protect(FLAG_PROTECT_SET,
-			      CONFIG_ENV_ADDR,
-			      CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
-			      &flash_info[0]);
-#endif
-
-	} else {
-		puts ("Warning: the BOOT Flash is not initialised !");
-	}
-
-	flash_to_mem();
-
-	return flash_size;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (ulong addr, flash_info_t *info)
-{
-	short i;
-	uchar value;
-	uchar *x = (uchar *)addr;
-
-	flash_to_xd();
-
-	/* Write auto select command: read Manufacturer ID */
-	x[0x0555] =  0xAA;
-	__asm__ volatile ("sync\n eieio");
-	x[0x02AA] =  0x55;
-	__asm__ volatile ("sync\n eieio");
-	x[0x0555] =  0x90;
-	__asm__ volatile ("sync\n eieio");
-
-	value = x[0];
-	__asm__ volatile ("sync\n eieio");
-
-	DEBUGF("Manuf. ID @ 0x%08lx: 0x%08x\n", (ulong)addr, value);
-
-	switch (value | (value << 16)) {
-		case AMD_MANUFACT:
-			info->flash_id = FLASH_MAN_AMD;
-			break;
-
-		case FUJ_MANUFACT:
-			info->flash_id = FLASH_MAN_FUJ;
-			break;
-
-		case STM_MANUFACT:
-			info->flash_id = FLASH_MAN_STM;
-			break;
-
-		default:
-			info->flash_id = FLASH_UNKNOWN;
-			info->sector_count = 0;
-			info->size = 0;
-			flash_reset (addr);
-			return 0;
-	}
-
-	value = x[1];
-	__asm__ volatile ("sync\n eieio");
-
-	DEBUGF("Device ID @ 0x%08lx: 0x%08x\n", addr+1, value);
-
-	switch (value) {
-		case AMD_ID_F040B:
-			DEBUGF("Am29F040B\n");
-			info->flash_id += FLASH_AM040;
-			info->sector_count = 8;
-			info->size = 0x00080000;
-			break;			/* => 512 kB		*/
-
-		case AMD_ID_LV040B:
-			DEBUGF("Am29LV040B\n");
-			info->flash_id += FLASH_AM040;
-			info->sector_count = 8;
-			info->size = 0x00080000;
-			break;			/* => 512 kB		*/
-
-		case AMD_ID_LV400T:
-			DEBUGF("Am29LV400T\n");
-			info->flash_id += FLASH_AM400T;
-			info->sector_count = 11;
-			info->size = 0x00100000;
-			break;			/* => 1 MB		*/
-
-		case AMD_ID_LV400B:
-			DEBUGF("Am29LV400B\n");
-			info->flash_id += FLASH_AM400B;
-			info->sector_count = 11;
-			info->size = 0x00100000;
-			break;			/* => 1 MB		*/
-
-		case AMD_ID_LV800T:
-			DEBUGF("Am29LV800T\n");
-			info->flash_id += FLASH_AM800T;
-			info->sector_count = 19;
-			info->size = 0x00200000;
-			break;			/* => 2 MB		*/
-
-		case AMD_ID_LV800B:
-			DEBUGF("Am29LV400B\n");
-			info->flash_id += FLASH_AM800B;
-			info->sector_count = 19;
-			info->size = 0x00200000;
-			break;			/* => 2 MB		*/
-
-		case AMD_ID_LV160T:
-			DEBUGF("Am29LV160T\n");
-			info->flash_id += FLASH_AM160T;
-			info->sector_count = 35;
-			info->size = 0x00400000;
-			break;			/* => 4 MB		*/
-
-		case AMD_ID_LV160B:
-			DEBUGF("Am29LV160B\n");
-			info->flash_id += FLASH_AM160B;
-			info->sector_count = 35;
-			info->size = 0x00400000;
-			break;			/* => 4 MB		*/
-
-		case AMD_ID_LV320T:
-			DEBUGF("Am29LV320T\n");
-			info->flash_id += FLASH_AM320T;
-			info->sector_count = 67;
-			info->size = 0x00800000;
-			break;			/* => 8 MB		*/
-
-#if 0
-		/* Has the same ID as AMD_ID_LV320T, to be fixed */
-		case AMD_ID_LV320B:
-			DEBUGF("Am29LV320B\n");
-			info->flash_id += FLASH_AM320B;
-			info->sector_count = 67;
-			info->size = 0x00800000;
-			break;			/* => 8 MB		*/
-#endif
-
-		case AMD_ID_LV033C:
-			DEBUGF("Am29LV033C\n");
-			info->flash_id += FLASH_AM033C;
-			info->sector_count = 64;
-			info->size = 0x01000000;
-			break;			/* => 16Mb		*/
-
-		case STM_ID_F040B:
-			DEBUGF("M29F040B\n");
-			info->flash_id += FLASH_AM040;
-			info->sector_count = 8;
-			info->size = 0x00080000;
-			break;			/* => 512 kB		*/
-
-		default:
-			info->flash_id = FLASH_UNKNOWN;
-			flash_reset (addr);
-			flash_to_mem();
-			return (0);		/* => no or unknown flash */
-
-	}
-
-	if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
-		printf ("** ERROR: sector count %d > max (%d) **\n",
-			info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
-		info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-	}
-
-	if (! flash_get_offsets (addr, info)) {
-		flash_reset (addr);
-		flash_to_mem();
-		return 0;
-	}
-
-	/* check for protected sectors */
-	for (i = 0; i < info->sector_count; i++) {
-		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
-		/* D0 = 1 if protected */
-		value = in8(info->start[i] + 2);
-		iobarrier_rw();
-		info->protect[i] = (value & 1) != 0;
-	}
-
-	/*
-	 * Reset bank to read mode
-	 */
-	flash_reset (addr);
-
-	flash_to_mem();
-
-	return (info->size);
-}
-
-static int flash_get_offsets (ulong base, flash_info_t *info)
-{
-	unsigned int i;
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-		case FLASH_AM040:
-			/* set sector offsets for uniform sector type	*/
-			for (i = 0; i < info->sector_count; i++) {
-				info->start[i] = base + i * info->size /
-							    info->sector_count;
-			}
-			break;
-		default:
-			return 0;
-	}
-
-	return 1;
-}
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	volatile ulong addr = info->start[0];
-	int flag, prot, sect, l_sect;
-	ulong start, now, last;
-
-	flash_to_xd();
-
-	if (s_first < 0 || s_first > s_last) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		flash_to_mem();
-		return 1;
-	}
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		flash_to_mem();
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	l_sect = -1;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	out8(addr + 0x555, 0xAA);
-	iobarrier_rw();
-	out8(addr + 0x2AA, 0x55);
-	iobarrier_rw();
-	out8(addr + 0x555, 0x80);
-	iobarrier_rw();
-	out8(addr + 0x555, 0xAA);
-	iobarrier_rw();
-	out8(addr + 0x2AA, 0x55);
-	iobarrier_rw();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			addr = info->start[sect];
-			out8(addr, 0x30);
-			iobarrier_rw();
-			l_sect = sect;
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay (1000);
-
-	/*
-	 * We wait for the last triggered sector
-	 */
-	if (l_sect < 0)
-		goto DONE;
-
-	start = get_timer (0);
-	last  = start;
-	addr = info->start[l_sect];
-
-	DEBUGF ("Start erase timeout: %d\n", CONFIG_SYS_FLASH_ERASE_TOUT);
-
-	while ((in8(addr) & 0x80) != 0x80) {
-		if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-			printf ("Timeout\n");
-			flash_reset (info->start[0]);
-			flash_to_mem();
-			return 1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 1000) {	/* every second */
-			putc ('.');
-			last = now;
-		}
-		iobarrier_rw();
-	}
-
-DONE:
-	/* reset to read mode */
-	flash_reset (info->start[0]);
-	flash_to_mem();
-
-	printf (" done\n");
-	return 0;
-}
-
-/*
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	flash_to_xd();
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word(info, wp, data)) != 0) {
-			flash_to_mem();
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, data)) != 0) {
-			flash_to_mem();
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		flash_to_mem();
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-
-	flash_to_mem();
-	return (write_word(info, wp, data));
-}
-
-/*
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	volatile ulong addr = info->start[0];
-	ulong start;
-	int i;
-
-	flash_to_xd();
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((in32(dest) & data) != data) {
-		flash_to_mem();
-		return (2);
-	}
-
-	/* write each byte out */
-	for (i = 0; i < 4; i++) {
-		char *data_ch = (char *)&data;
-		int flag = disable_interrupts();
-
-		out8(addr + 0x555, 0xAA);
-		iobarrier_rw();
-		out8(addr + 0x2AA, 0x55);
-		iobarrier_rw();
-		out8(addr + 0x555, 0xA0);
-		iobarrier_rw();
-		out8(dest+i, data_ch[i]);
-		iobarrier_rw();
-
-		/* re-enable interrupts if necessary */
-		if (flag)
-			enable_interrupts();
-
-		/* data polling for D7 */
-		start = get_timer (0);
-		while ((in8(dest+i) & 0x80) != (data_ch[i] & 0x80)) {
-			if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-				flash_reset (addr);
-				flash_to_mem();
-				return (1);
-			}
-			iobarrier_rw();
-		}
-	}
-
-	flash_reset (addr);
-	flash_to_mem();
-	return (0);
-}
-
-/*
- * Reset bank to read mode
- */
-static void flash_reset (ulong addr)
-{
-	flash_to_xd();
-	out8(addr, 0xF0);	/* reset bank */
-	iobarrier_rw();
-	flash_to_mem();
-}
-
-void flash_print_info (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:	printf ("AMD ");		break;
-	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
-	case FLASH_MAN_BM:	printf ("BRIGHT MICRO ");	break;
-	case FLASH_MAN_STM:	printf ("SGS THOMSON ");	break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AM040:	printf ("29F040 or 29LV040 (4 Mbit, uniform sectors)\n");
-				break;
-	case FLASH_AM400B:	printf ("AM29LV400B (4 Mbit, bottom boot sect)\n");
-				break;
-	case FLASH_AM400T:	printf ("AM29LV400T (4 Mbit, top boot sector)\n");
-				break;
-	case FLASH_AM800B:	printf ("AM29LV800B (8 Mbit, bottom boot sect)\n");
-				break;
-	case FLASH_AM800T:	printf ("AM29LV800T (8 Mbit, top boot sector)\n");
-				break;
-	case FLASH_AM160B:	printf ("AM29LV160B (16 Mbit, bottom boot sect)\n");
-				break;
-	case FLASH_AM160T:	printf ("AM29LV160T (16 Mbit, top boot sector)\n");
-				break;
-	case FLASH_AM320B:	printf ("AM29LV320B (32 Mbit, bottom boot sect)\n");
-				break;
-	case FLASH_AM320T:	printf ("AM29LV320T (32 Mbit, top boot sector)\n");
-				break;
-	default:		printf ("Unknown Chip Type\n");
-				break;
-	}
-
-	if (info->size % 0x100000 == 0) {
-		printf ("  Size: %ld MB in %d Sectors\n",
-			info->size / 0x100000, info->sector_count);
-	} else if (info->size % 0x400 == 0) {
-		printf ("  Size: %ld KB in %d Sectors\n",
-			info->size / 0x400, info->sector_count);
-	} else {
-		printf ("  Size: %ld B in %d Sectors\n",
-			info->size, info->sector_count);
-	}
-
-	printf ("  Sector Start Addresses:");
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-		);
-	}
-	printf ("\n");
-}
diff --git a/board/MAI/AmigaOneG3SE/i8259.c b/board/MAI/AmigaOneG3SE/i8259.c
deleted file mode 100644
index 34f489f..0000000
--- a/board/MAI/AmigaOneG3SE/i8259.c
+++ /dev/null
@@ -1,230 +0,0 @@
-/*
- * (C) Copyright 2002
- * John W. Linville, linville@tuxdriver.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include "i8259.h"
-
-#undef  IRQ_DEBUG
-
-#ifdef  IRQ_DEBUG
-#define PRINTF(fmt,args...)     printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-static inline unsigned char read_byte(volatile unsigned char* from)
-{
-    int x;
-    asm volatile ("lbz %0,%1\n eieio" : "=r" (x) : "m" (*from));
-    return (unsigned char)x;
-}
-
-static inline void write_byte(volatile unsigned char *to, int x)
-{
-    asm volatile ("stb %1,%0\n eieio" : "=m" (*to) : "r" (x));
-}
-
-static inline unsigned long read_long_little(volatile unsigned long *from)
-{
-    unsigned long x;
-    asm volatile ("lwbrx %0,0,%1\n eieio\n sync" : "=r" (x) : "r" (from), "m"(*from));
-    return (unsigned long)x;
-}
-
-#ifdef out8
-#undef out8
-#endif
-
-#ifdef in8
-#undef in8
-#endif
-
-#define out8(addr, byte) write_byte(0xFE000000 | addr, byte)
-#define in8(addr) read_byte(0xFE000000 | addr)
-
-/*
- * This contains the irq mask for both 8259A irq controllers,
- */
-static char cached_imr[2] = {0xff, 0xff};
-
-#define cached_imr1	(cached_imr[0])
-#define cached_imr2	(cached_imr[1])
-
-void i8259_init(void)
-{
-	char dummy;
-	PRINTF("Initializing Interrupt controller\n");
-	/* init master interrupt controller */
-	out8(0x20, 0x11); /* 0x19); /###* Start init sequence */
-	out8(0x21, 0x00); /* Vector base */
-	out8(0x21, 0x04); /* edge tiggered, Cascade (slave) on IRQ2 */
-	out8(0x21, 0x11); /* was: 0x01); /###* Select 8086 mode */
-
-	/* init slave interrupt controller */
-	out8(0xA0, 0x11); /* 0x19); /###* Start init sequence */
-	out8(0xA1, 0x08); /* Vector base */
-	out8(0xA1, 0x02); /* edge triggered, Cascade (slave) on IRQ2 */
-	out8(0xA1, 0x11); /* was: 0x01); /###* Select 8086 mode */
-
-	/* always read ISR */
-	out8(0x20, 0x0B);
-	dummy = in8(ISR_1);
-	out8(0xA0, 0x0B);
-	dummy = in8(ISR_2);
-
-/*     out8(0x43, 0x30); */
-/*     out8(0x40, 0); */
-/*     out8(0x40, 0); */
-/*     out8(0x43, 0x70); */
-/*     out8(0x41, 0); */
-/*     out8(0x41, 0); */
-/*     out8(0x43, 0xb0); */
-/*     out8(0x42, 0); */
-/*     out8(0x42, 0); */
-
-	/* Mask all interrupts */
-	out8(IMR_2, cached_imr2);
-	out8(IMR_1, cached_imr1);
-
-	i8259_unmask_irq(2);
-#if 0
-	{
-	    int i;
-	    for (i=0; i<16; i++)
-	    {
-		i8259_unmask_irq(i);
-	    }
-	}
-#endif
-}
-
-static volatile char *pci_intack = (void *)0xFEF00000;
-
-int i8259_irq(void)
-{
-	int irq;
-
-	irq = read_long_little(pci_intack) & 0xff;
-	if (irq==7) {
-		/*
-		 * This may be a spurious interrupt.
-		 *
-		 * Read the interrupt status register (ISR). If the most
-		 * significant bit is not set then there is no valid
-		 * interrupt.
-		 */
-		if(~in8(0x20)&0x80) {
-			irq = -1;
-		}
-	}
-
-	return irq;
-}
-int i8259_get_irq(struct pt_regs *regs)
-{
-	unsigned char irq;
-
-	/*
-	 * Perform an interrupt acknowledge cycle on controller 1
-	 */
-	out8(OCW3_1, 0x0C); /* prepare for poll */
-	irq = in8(IPL_1) & 7;
-	if (irq == 2) {
-		/*
-		 * Interrupt is cascaded so perform interrupt
-		 * acknowledge on controller 2
-		 */
-		out8(OCW3_2, 0x0C); /* prepare for poll */
-		irq = (in8(IPL_2) & 7) + 8;
-		if (irq == 15) {
-			/*
-			 * This may be a spurious interrupt
-			 *
-			 * Read the interrupt status register. If the most
-			 * significant bit is not set then there is no valid
-			 * interrupt
-			 */
-			out8(OCW3_2, 0x0b);
-			if (~(in8(ISR_2) & 0x80)) {
-				return -1;
-			}
-		}
-	} else if (irq == 7) {
-		/*
-		 * This may be a spurious interrupt
-		 *
-		 * Read the interrupt status register. If the most
-		 * significant bit is not set then there is no valid
-		 * interrupt
-		 */
-		out8(OCW3_1, 0x0b);
-		if (~(in8(ISR_1) & 0x80)) {
-			return -1;
-		}
-	}
-	return irq;
-}
-
-/*
- * Careful! The 8259A is a fragile beast, it pretty
- * much _has_ to be done exactly like this (mask it
- * first, _then_ send the EOI, and the order of EOI
- * to the two 8259s is important!
- */
-void i8259_mask_and_ack(int irq)
-{
-	if (irq > 7) {
-		cached_imr2 |= (1 << (irq - 8));
-		in8(IMR_2); /* DUMMY */
-		out8(IMR_2, cached_imr2);
-		out8(OCW2_2, 0x20); /* Non-specific EOI */
-		out8(OCW2_1, 0x20); /* Non-specific EOI to cascade */
-	} else {
-		cached_imr1 |= (1 << irq);
-		in8(IMR_1); /* DUMMY */
-		out8(IMR_1, cached_imr1);
-		out8(OCW2_1, 0x20); /* Non-specific EOI */
-	}
-}
-
-void i8259_mask_irq(int irq)
-{
-	if (irq & 8) {
-		cached_imr2 |= (1 << (irq & 7));
-		out8(IMR_2, cached_imr2);
-	} else {
-		cached_imr1 |= (1 << irq);
-		out8(IMR_1, cached_imr1);
-	}
-}
-
-void i8259_unmask_irq(int irq)
-{
-	if (irq & 8) {
-		cached_imr2 &= ~(1 << (irq & 7));
-		out8(IMR_2, cached_imr2);
-	} else {
-		cached_imr1 &= ~(1 << irq);
-		out8(IMR_1, cached_imr1);
-	}
-}
diff --git a/board/MAI/AmigaOneG3SE/i8259.h b/board/MAI/AmigaOneG3SE/i8259.h
deleted file mode 100644
index eb08e13..0000000
--- a/board/MAI/AmigaOneG3SE/i8259.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * (C) Copyright 2002
- * John W. Linville, linville@tuxdriver.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#define ICW1_1  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT1_ICW1
-#define ICW1_2  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT2_ICW1
-#define ICW2_1  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT1_ICW2
-#define ICW2_2  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT2_ICW2
-#define ICW3_1  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT1_ICW3
-#define ICW3_2  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT2_ICW3
-#define ICW4_1  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT1_ICW4
-#define ICW4_2  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT2_ICW4
-#define OCW1_1  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT1_OCW1
-#define OCW1_2  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT2_OCW1
-#define OCW2_1  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT1_OCW2
-#define OCW2_2  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT2_OCW2
-#define OCW3_1  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT1_OCW3
-#define OCW3_2  CONFIG_SYS_ISA_IO_BASE_ADDRESS + ISA_INT2_OCW3
-
-#define IMR_1   OCW1_1
-#define IMR_2   OCW1_2
-
-#define ISR_1   ICW1_1
-#define ISR_2   ICW1_2
-
-#define IPL_1   ICW1_1
-#define IPL_2   ICW1_2
-
-extern void i8259_init(void);
-
-extern int i8259_get_irq(struct pt_regs *regs);
-
-extern void i8259_mask_and_ack(int irq);
-
-extern void i8259_mask_irq(int irq);
-
-extern void i8259_unmask_irq(int irq);
diff --git a/board/MAI/AmigaOneG3SE/interrupts.c b/board/MAI/AmigaOneG3SE/interrupts.c
deleted file mode 100644
index de46d6e..0000000
--- a/board/MAI/AmigaOneG3SE/interrupts.c
+++ /dev/null
@@ -1,266 +0,0 @@
-/*
- * (C) Copyright 2002
- * John W. Linville <linville@tuxdriver.com>
- *
- *    Copied and modified from original code by Josh Huber.  Original
- *    copyright notice preserved below.
- *
- * (C) Copyright 2001
- * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * interrupts.c - just enough support for the decrementer/timer
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <command.h>
-#include "i8259.h"
-
-#undef DEBUG
-#ifdef  DEBUG
-#define PRINTF(fmt,args...)     printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-#define NR_IRQS	16
-
-void irq_alloc_init(void);
-long irq_alloc(long wanted);
-
-/****************************************************************************/
-
-unsigned decrementer_count;	     /* count value for 1e6/HZ microseconds */
-
-struct irq_action {
-    interrupt_handler_t *handler;
-    void *arg;
-    ulong count;
-};
-
-static struct irq_action irq_handlers[NR_IRQS];
-
-/****************************************************************************/
-
-static __inline__ unsigned long
-get_msr(void)
-{
-	unsigned long msr;
-
-	asm volatile("mfmsr %0" : "=r" (msr) :);
-	return msr;
-}
-
-static __inline__ void
-set_msr(unsigned long msr)
-{
-	asm volatile("mtmsr %0" : : "r" (msr));
-}
-
-static __inline__ unsigned long
-get_dec(void)
-{
-	unsigned long val;
-
-	asm volatile("mfdec %0" : "=r" (val) :);
-	return val;
-}
-
-
-static __inline__ void
-set_dec(unsigned long val)
-{
-	asm volatile("mtdec %0" : : "r" (val));
-}
-
-
-void
-enable_interrupts(void)
-{
-    set_msr (get_msr() | MSR_EE);
-}
-
-/* returns flag if MSR_EE was set before */
-int
-disable_interrupts(void)
-{
-    ulong msr;
-
-    msr = get_msr();
-    set_msr (msr & ~MSR_EE);
-    return ((msr & MSR_EE) != 0);
-}
-
-/****************************************************************************/
-
-int interrupt_init (void)
-{
-    extern void new_reset(void);
-    extern void new_reset_end(void);
-#ifdef DEBUG
-	puts("interrupt_init: setting decrementer_count\n");
-#endif
-	decrementer_count = get_tbclk() / CONFIG_SYS_HZ;
-
-#ifdef DEBUG
-	puts("interrupt_init: setting actual decremter\n");
-#endif
-	set_dec (get_tbclk() / CONFIG_SYS_HZ);
-
-#ifdef DEBUG
-	puts("interrupt_init: clearing external interrupt table\n");
-#endif
-	/* clear external interrupt table here */
-	memset(irq_handlers, 0, sizeof(irq_handlers));
-
-#ifdef DEBUG
-	puts("interrupt_init: initializing interrupt controller\n");
-#endif
-	i8259_init();
-
-#ifdef DEBUG
-	puts("Copying reset trampoline\n");
-#endif
-	/* WARNING: Assmues that the first megabyte is CACHEINHIBIT! */
-	memcpy((void *)0x100, new_reset, new_reset_end - new_reset);
-
-#ifdef DEBUG
-	PRINTF("interrupt_init: enabling interrupts (msr = %08x)\n",
-		get_msr());
-#endif
-	set_msr (get_msr() | MSR_EE);
-
-#ifdef DEBUG
-	PRINTF("interrupt_init: done. (msr = %08x)\n", get_msr());
-#endif
-
-}
-
-/****************************************************************************/
-
-/*
- * Handle external interrupts
- */
-void
-external_interrupt(struct pt_regs *regs)
-{
-    extern int i8259_irq(void);
-
-	int irq, unmask = 1;
-
-	irq = i8259_irq(); /*i8259_get_irq(regs); */
-/*	printf("irq = %d, handler at %p ack=%d\n", irq, irq_handlers[irq].handler, *(volatile unsigned char *)0xFEF00000); */
-	i8259_mask_and_ack(irq);
-
-	if (irq_handlers[irq].handler != NULL)
-		(*irq_handlers[irq].handler)(irq_handlers[irq].arg);
-	else {
-		PRINTF ("\nBogus External Interrupt IRQ %d\n", irq);
-		/*
-		* turn off the bogus interrupt, otherwise it
-		* might repeat forever
-		*/
-		unmask = 0;
-	}
-
-	if (unmask) i8259_unmask_irq(irq);
-}
-
-volatile ulong timestamp = 0;
-
-/*
- * timer_interrupt - gets called when the decrementer overflows,
- * with interrupts disabled.
- * Trivial implementation - no need to be really accurate.
- */
-void
-timer_interrupt(struct pt_regs *regs)
-{
-	set_dec(decrementer_count);
-	timestamp++;
-}
-
-/****************************************************************************/
-
-void
-reset_timer(void)
-{
-	timestamp = 0;
-}
-
-ulong
-get_timer(ulong base)
-{
-	return (timestamp - base);
-}
-
-void
-set_timer(ulong t)
-{
-	timestamp = t;
-}
-
-/****************************************************************************/
-
-/*
- * Install and free a interrupt handler.
- */
-
-void
-irq_install_handler(int irq, interrupt_handler_t *handler, void *arg)
-{
-	if (irq < 0 || irq >= NR_IRQS) {
-		PRINTF("irq_install_handler: bad irq number %d\n", irq);
-		return;
-	}
-
-	if (irq_handlers[irq].handler != NULL)
-		PRINTF("irq_install_handler: 0x%08lx replacing 0x%08lx\n",
-		       (ulong)handler, (ulong)irq_handlers[irq].handler);
-
-	irq_handlers[irq].handler = handler;
-	irq_handlers[irq].arg     = arg;
-
-	i8259_unmask_irq(irq);
-}
-
-void
-irq_free_handler(int irq)
-{
-	if (irq < 0 || irq >= NR_IRQS) {
-		PRINTF("irq_free_handler: bad irq number %d\n", irq);
-		return;
-	}
-
-	i8259_mask_irq(irq);
-
-	irq_handlers[irq].handler = NULL;
-	irq_handlers[irq].arg     = NULL;
-}
-
-/****************************************************************************/
-
-void
-do_irqinfo(cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[])
-{
-	puts("IRQ related functions are unimplemented currently.\n");
-}
diff --git a/board/MAI/AmigaOneG3SE/macros.h b/board/MAI/AmigaOneG3SE/macros.h
deleted file mode 100644
index 6020d7e..0000000
--- a/board/MAI/AmigaOneG3SE/macros.h
+++ /dev/null
@@ -1,84 +0,0 @@
-
-#ifndef _MACROS_H
-#define _MACROS_H
-
-	/*
-	** Load a long integer into a register
-	*/
-	.macro liw reg, value
-		lis \reg, \value@h
-		ori \reg, \reg, \value@l
-	.endm
-
-
-	/*
-	** Generate config_addr request
-	** This macro expects the values in registers:
-	** r3 - bus
-	** r4 - devfn
-	** r5 - offset
-	*/
-	.macro config_addr
-		rlwinm	r9, r5, 24, 0, 6
-		rlwinm	r8, r4, 16, 0, 31
-		rlwinm	r7, r3, 8, 0, 31
-		or	r9, r8, r9
-		or	r9, r7, r9
-		ori	r9, r9, 0x80
-		liw	r10, 0xfec00cf8
-		stw	r9, 0(r10)
-		eieio
-		sync
-	.endm
-
-
-	/*
-	** Generate config_data address
-	*/
-	.macro config_data mask
-		andi.	r9, r5, \mask
-		addi	r9, r9, 0xcfc
-		oris	r9, r9, 0xfee0
-	.endm
-
-
-	/*
-	** Write a byte value to an output port
-	*/
-	.macro outb port, value
-		lis     r2, 0xfe00
-		li      r0, \value
-		stb     r0, \port(r2)
-	.endm
-
-
-	/*
-	** Write a register byte value to an output port
-	*/
-	.macro outbr port, value
-		lis     r2, 0xfe00
-		stb     \value, \port(r2)
-	.endm
-
-
-	/*
-	** Read a byte value from a port into a specified register
-	*/
-	.macro inb reg, port
-		lis     r2, 0xfe00
-		lbz     \reg, \port(r2)
-	.endm
-
-
-	/*
-	** Write a byte to the SuperIO config area
-	*/
-	.macro siowb offset, value
-		li      r3, 0
-		li      r4, (7<<3)
-		li      r5, \offset
-		li      r6, \value
-		bl      pci_write_cfg_byte
-	.endm
-
-#endif
diff --git a/board/MAI/AmigaOneG3SE/memio.S b/board/MAI/AmigaOneG3SE/memio.S
deleted file mode 100644
index 980d343..0000000
--- a/board/MAI/AmigaOneG3SE/memio.S
+++ /dev/null
@@ -1,67 +0,0 @@
-#include	"macros.h"
-
-
-	.globl pci_read_cfg_byte
-
-pci_read_cfg_byte:
-	config_addr
-	config_data	3
-	eieio
-	sync
-	lbz	r3, 0(r9)
-	blr
-
-
-	.globl pci_write_cfg_byte
-
-pci_write_cfg_byte:
-	config_addr
-	config_data	3
-	stb	r6, 0(r9)
-	eieio
-	sync
-	blr
-
-
-	.globl pci_read_cfg_word
-
-pci_read_cfg_word:
-	config_addr
-	config_data	2
-	lhbrx	r3, 0, r9
-	eieio
-	sync
-	blr
-
-
-	.globl pci_write_cfg_word
-
-pci_write_cfg_word:
-	config_addr
-	config_data	2
-	sthbrx	r6, 0, r9
-	eieio
-	sync
-	blr
-
-
-	.globl pci_read_cfg_long
-
-pci_read_cfg_long:
-	config_addr
-	config_data	0
-	lwbrx	r3, 0, r9
-	eieio
-	sync
-	blr
-
-
-	.globl pci_write_cfg_long
-
-pci_write_cfg_long:
-	config_addr
-	config_data	0
-	stwbrx	r6, 0, r9
-	eieio
-	sync
-	blr
diff --git a/board/MAI/AmigaOneG3SE/memio.h b/board/MAI/AmigaOneG3SE/memio.h
deleted file mode 100644
index f5ce303..0000000
--- a/board/MAI/AmigaOneG3SE/memio.h
+++ /dev/null
@@ -1,113 +0,0 @@
-/*
- * Memory mapped IO
- *
- * (C) Copyright 2002
- * Hyperion Entertainment, ThomasF@hyperion-entertainment.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- * You may also use this under a BSD license.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
- *
- */
-
-#ifndef _MEMIO_H
-#define _MEMIO_H
-
-#include "short_types.h"
-
-#define IOBASE 0xFE000000
-
-#define in_byte(from) read_byte( (uint8 *)(IOBASE | (from)))
-#define in_word(from) read_word_little((uint16 *)(IOBASE | (from)))
-#define in_long(from) read_long_little((uint32 *)(IOBASE | (from)))
-#define out_byte(to, val) write_byte((uint8 *)(IOBASE | (to)), val)
-#define out_word(to, val) write_word_little((uint16 *)(IOBASE | (to)), val)
-#define out_long(to, val) write_long_little((uint32 *)(IOBASE | (to)), val)
-
-
-static inline uint8 read_byte(volatile uint8 *from)
-{
-    int x;
-    asm volatile ("lbz %0,%1\n eieio\n sync" : "=r" (x) : "m" (*from));
-    return (uint8)x;
-}
-
-
-static inline void write_byte(volatile uint8 *to, uint8 x)
-{
-    asm volatile ("stb %1,%0\n eieio\n sync" : "=m" (*to) : "r" (x));
-}
-
-static inline uint16 read_word_little(volatile uint16 *from)
-{
-    int x;
-    asm volatile ("lhbrx %0,0,%1\n eieio\n sync" : "=r" (x) : "r" (from), "m" (*from));
-    return (uint16)x;
-}
-
-static inline uint16 read_word_big(volatile uint16 *from)
-{
-    int x;
-    asm volatile ("lhz %0,%1\n eieio\n sync" : "=r" (x) : "m" (*from));
-    return (uint16)x;
-}
-
-static inline void write_word_little(volatile uint16 *to, int x)
-{
-    asm volatile ("sthbrx %1,0,%2\n eieio\n sync" : "=m" (*to) : "r" (x), "r" (to));
-}
-
-static inline void write_word_big(volatile uint16 *to, int x)
-{
-    asm volatile ("sth %1,%0\n eieio\n sync" : "=m" (*to) : "r" (x));
-}
-
-static inline uint32 read_long_little(volatile uint32 *from)
-{
-    unsigned long x;
-    asm volatile ("lwbrx %0,0,%1\n eieio\n sync" : "=r" (x) : "r" (from), "m"(*from));
-    return (uint32)x;
-}
-
-static inline uint32 read_long_big(volatile uint32 *from)
-{
-    unsigned long x;
-    asm volatile ("lwz %0,%1\n eieio\n sync" : "=r" (x) : "m" (*from));
-    return (uint32)x;
-}
-
-static inline void write_long_little(volatile uint32 *to, uint32 x)
-{
-    asm volatile ("stwbrx %1,0,%2\n eieio\n sync" : "=m" (*to) : "r" (x), "r" (to));
-}
-
-static inline void write_long_big(volatile uint32 *to, uint32 x)
-{
-    asm volatile ("stw %1,%0\n eieio\n sync" : "=m" (*to) : "r" (x));
-}
-
-#define CONFIG_ADDR(bus, devfn, offset) \
-    write_long_big((uint32 *)0xFEC00CF8,           \
-		   ((offset & 0xFC)<<24) | (devfn << 16)  \
-		   | (bus<<8) | 0x80);
-#define CONFIG_DATA(offset,mask) ((void *)(0xFEE00CFC+(offset & mask)))
-
-
-uint8 pci_read_cfg_byte(int32 bus, int32 devfn, int32 offset);
-void pci_write_cfg_byte(int32 bus, int32 devfn, int32 offset, uint8 x);
-uint16 pci_read_cfg_word(int32 bus, int32 devfn, int32 offset);
-void pci_write_cfg_word(int32 bus, int32 devfn, int32 offset, uint16 x);
-uint32 pci_read_cfg_long(int32 bus, int32 devfn, int32 offset);
-void pci_write_cfg_long(int32 bus, int32 devfn, int32 offset, uint32 x);
-
-
-#endif
diff --git a/board/MAI/AmigaOneG3SE/memory_dump b/board/MAI/AmigaOneG3SE/memory_dump
deleted file mode 100644
index 65e7936..0000000
--- a/board/MAI/AmigaOneG3SE/memory_dump
+++ /dev/null
@@ -1,30 +0,0 @@
-64 MB:
-0x00: 80 08 04 0c 09 01 40 00 01 a0 60 00 80 08 00 01
-0x10: 8f 04 04 01 01 00 06 a0 60 00 00 14 10 14 2d 10
-0x20: 20 10 20 10 00 00 00 00 00 00 00 00 00 00 00 00
-0x30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 f2
-0x40: 7f 61 00 00 00 00 00 00 46 04 00 ff ff ff ff ff
-0x50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
-0x60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
-0x70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff 64 f4
-
-512 MB:
-0x00: 80 08 04 0d 0a 02 40 00 01 75 54 00 82 08 00 01
-0x10: 8f 04 04 01 01 00 0f 00 00 00 00 14 0f 14 2d 40
-0x20: 15 08 15 08 00 00 00 00 00 00 00 00 00 00 00 00
-0x30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 d2
-0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
-0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
-0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
-0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 fd
-
-256 MB:
-0x00: 80 08 04 0c 0a 02 40 00 01 75 54 00 80 08 00 01
-0x10: 8f 04 06 01 01 00 0e a0 60 00 00 14 0f 14 2d 20
-0x20: 15 08 15 08 00 00 00 00 00 00 00 00 00 00 00 00
-0x30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 b0
-0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
-0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
-0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
-0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 f6
-
diff --git a/board/MAI/AmigaOneG3SE/nvram.c b/board/MAI/AmigaOneG3SE/nvram.c
deleted file mode 100644
index d37eec1..0000000
--- a/board/MAI/AmigaOneG3SE/nvram.c
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * (C) Copyright 2002
- * Thomas Frieden, Hyperion Entertainment
- * ThomasF@hyperion-entertainment.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include "memio.h"
-
-void enable_nvram(void)
-{
-    pci_write_cfg_byte(0, 0, 0x56, 0x0b);
-}
-
-void disable_nvram(void)
-{
-    pci_write_cfg_byte(0, 0, 0x56, 0x0);
-}
diff --git a/board/MAI/AmigaOneG3SE/ps2kbd.c b/board/MAI/AmigaOneG3SE/ps2kbd.c
deleted file mode 100644
index aa164b0..0000000
--- a/board/MAI/AmigaOneG3SE/ps2kbd.c
+++ /dev/null
@@ -1,685 +0,0 @@
-/*
- * (C) Copyright 2002
- * John W. Linville, linville@tuxdriver.com
- *
- * Modified from code for support of MIP405 and PIP405 boards.  Previous
- * copyright follows.
- *
- * (C) Copyright 2001
- * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- *
- * Source partly derived from:
- * linux/drivers/char/pc_keyb.c
- *
- *
- */
-#include <common.h>
-#include <asm/processor.h>
-#include <stdio_dev.h>
-#include "ps2kbd.h"
-
-
-unsigned char kbd_read_status(void);
-unsigned char kbd_read_input(void);
-void kbd_send_data(unsigned char data);
-void i8259_mask_irq(unsigned int irq);
-void i8259_unmask_irq(unsigned int irq);
-
-/* used only by send_data - set by keyboard_interrupt */
-
-
-#undef KBG_DEBUG
-
-#ifdef KBG_DEBUG
-#define	PRINTF(fmt,args...)	printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-#define KBD_STAT_KOBF		0x01
-#define KBD_STAT_IBF		0x02
-#define KBD_STAT_SYS		0x04
-#define KBD_STAT_CD		0x08
-#define KBD_STAT_LOCK		0x10
-#define KBD_STAT_MOBF		0x20
-#define KBD_STAT_TI_OUT	0x40
-#define KBD_STAT_PARERR	0x80
-
-#define KBD_INIT_TIMEOUT 2000		/* Timeout in ms for initializing the keyboard */
-#define KBC_TIMEOUT 250			/* Timeout in ms for sending to keyboard controller */
-#define KBD_TIMEOUT 2000		/* Timeout in ms for keyboard command acknowledge */
-/*
- *	Keyboard Controller Commands
- */
-
-#define KBD_CCMD_READ_MODE	0x20	/* Read mode bits */
-#define KBD_CCMD_WRITE_MODE	0x60	/* Write mode bits */
-#define KBD_CCMD_GET_VERSION	0xA1	/* Get controller version */
-#define KBD_CCMD_MOUSE_DISABLE	0xA7	/* Disable mouse interface */
-#define KBD_CCMD_MOUSE_ENABLE	0xA8	/* Enable mouse interface */
-#define KBD_CCMD_TEST_MOUSE	0xA9	/* Mouse interface test */
-#define KBD_CCMD_SELF_TEST	0xAA	/* Controller self test */
-#define KBD_CCMD_KBD_TEST	0xAB	/* Keyboard interface test */
-#define KBD_CCMD_KBD_DISABLE	0xAD	/* Keyboard interface disable */
-#define KBD_CCMD_KBD_ENABLE	0xAE	/* Keyboard interface enable */
-#define KBD_CCMD_WRITE_AUX_OBUF	0xD3    /* Write to output buffer as if
-					   initiated by the auxiliary device */
-#define KBD_CCMD_WRITE_MOUSE	0xD4	/* Write the following byte to the mouse */
-
-/*
- *	Keyboard Commands
- */
-
-#define KBD_CMD_SET_LEDS	0xED	/* Set keyboard leds */
-#define KBD_CMD_SET_RATE	0xF3	/* Set typematic rate */
-#define KBD_CMD_ENABLE		0xF4	/* Enable scanning */
-#define KBD_CMD_DISABLE		0xF5	/* Disable scanning */
-#define KBD_CMD_RESET		0xFF	/* Reset */
-
-/*
- *	Keyboard Replies
- */
-
-#define KBD_REPLY_POR		0xAA	/* Power on reset */
-#define KBD_REPLY_ACK		0xFA	/* Command ACK */
-#define KBD_REPLY_RESEND	0xFE	/* Command NACK, send the cmd again */
-
-/*
- *	Status Register Bits
- */
-
-#define KBD_STAT_OBF		0x01	/* Keyboard output buffer full */
-#define KBD_STAT_IBF		0x02	/* Keyboard input buffer full */
-#define KBD_STAT_SELFTEST	0x04	/* Self test successful */
-#define KBD_STAT_CMD		0x08	/* Last write was a command write (0=data) */
-#define KBD_STAT_UNLOCKED	0x10	/* Zero if keyboard locked */
-#define KBD_STAT_MOUSE_OBF	0x20	/* Mouse output buffer full */
-#define KBD_STAT_GTO		0x40	/* General receive/xmit timeout */
-#define KBD_STAT_PERR		0x80	/* Parity error */
-
-#define AUX_STAT_OBF (KBD_STAT_OBF | KBD_STAT_MOUSE_OBF)
-
-/*
- *	Controller Mode Register Bits
- */
-
-#define KBD_MODE_KBD_INT	0x01	/* Keyboard data generate IRQ1 */
-#define KBD_MODE_MOUSE_INT	0x02	/* Mouse data generate IRQ12 */
-#define KBD_MODE_SYS		0x04	/* The system flag (?) */
-#define KBD_MODE_NO_KEYLOCK	0x08	/* The keylock doesn't affect the keyboard if set */
-#define KBD_MODE_DISABLE_KBD	0x10	/* Disable keyboard interface */
-#define KBD_MODE_DISABLE_MOUSE	0x20	/* Disable mouse interface */
-#define KBD_MODE_KCC		0x40	/* Scan code conversion to PC format */
-#define KBD_MODE_RFU		0x80
-
-
-#define KDB_DATA_PORT		0x60
-#define KDB_COMMAND_PORT	0x64
-
-#define	LED_SCR			0x01	/* scroll lock led */
-#define	LED_CAP			0x04	/* caps lock led */
-#define	LED_NUM			0x02	/* num lock led */
-
-#define	KBD_BUFFER_LEN		0x20	/* size of the keyboardbuffer */
-
-
-static volatile char kbd_buffer[KBD_BUFFER_LEN];
-static volatile int in_pointer = 0;
-static volatile int out_pointer = 0;
-
-
-static unsigned char num_lock = 0;
-static unsigned char caps_lock = 0;
-static unsigned char scroll_lock = 0;
-static unsigned char shift = 0;
-static unsigned char ctrl = 0;
-static unsigned char alt = 0;
-static unsigned char e0 = 0;
-static unsigned char leds = 0;
-
-#define DEVNAME "ps2kbd"
-
-/* Simple translation table for the keys */
-
-static unsigned char kbd_plain_xlate[] = {
-	0xff,0x1b, '1', '2', '3', '4', '5', '6', '7', '8', '9', '0', '-', '=','\b','\t',	/* 0x00 - 0x0f */
-	 'q', 'w', 'e', 'r', 't', 'y', 'u', 'i', 'o', 'p', '[', ']','\r',0xff, 'a', 's',	/* 0x10 - 0x1f */
-	 'd', 'f', 'g', 'h', 'j', 'k', 'l', ';','\'', '`',0xff,'\\', 'z', 'x', 'c', 'v',	/* 0x20 - 0x2f */
-	 'b', 'n', 'm', ',', '.', '/',0xff,0xff,0xff, ' ',0xff,0xff,0xff,0xff,0xff,0xff,	/* 0x30 - 0x3f */
-	0xff,0xff,0xff,0xff,0xff,0xff,0xff, '7', '8', '9', '-', '4', '5', '6', '+', '1',	/* 0x40 - 0x4f */
-	 '2', '3', '0', '.',0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,  /* 0x50 - 0x5F */
-	'\r',0xff,0xff
-	};
-
-static unsigned char kbd_shift_xlate[] = {
-	0xff,0x1b, '!', '@', '#', '$', '%', '^', '&', '*', '(', ')', '_', '+','\b','\t',	/* 0x00 - 0x0f */
-	 'Q', 'W', 'E', 'R', 'T', 'Y', 'U', 'I', 'O', 'P', '{', '}','\r',0xff, 'A', 'S',	/* 0x10 - 0x1f */
-	 'D', 'F', 'G', 'H', 'J', 'K', 'L', ':', '"', '~',0xff, '|', 'Z', 'X', 'C', 'V',	/* 0x20 - 0x2f */
-	 'B', 'N', 'M', '<', '>', '?',0xff,0xff,0xff, ' ',0xff,0xff,0xff,0xff,0xff,0xff,	/* 0x30 - 0x3f */
-	0xff,0xff,0xff,0xff,0xff,0xff,0xff, '7', '8', '9', '-', '4', '5', '6', '+', '1',	/* 0x40 - 0x4f */
-	 '2', '3', '0', '.',0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,  /* 0x50 - 0x5F */
-	'\r',0xff,0xff
-	};
-
-static unsigned char kbd_ctrl_xlate[] = {
-	0xff,0x1b, '1',0x00, '3', '4', '5',0x1E, '7', '8', '9', '0',0x1F, '=','\b','\t',	/* 0x00 - 0x0f */
-	0x11,0x17,0x05,0x12,0x14,0x18,0x15,0x09,0x0f,0x10,0x1b,0x1d,'\n',0xff,0x01,0x13,	/* 0x10 - 0x1f */
-	0x04,0x06,0x08,0x09,0x0a,0x0b,0x0c, ';','\'', '~',0x00,0x1c,0x1a,0x18,0x03,0x16,	/* 0x20 - 0x2f */
-	0x02,0x0e,0x0d, '<', '>', '?',0xff,0xff,0xff,0x00,0xff,0xff,0xff,0xff,0xff,0xff,	/* 0x30 - 0x3f */
-	0xff,0xff,0xff,0xff,0xff,0xff,0xff, '7', '8', '9', '-', '4', '5', '6', '+', '1',	/* 0x40 - 0x4f */
-	 '2', '3', '0', '.',0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,  /* 0x50 - 0x5F */
-	'\r',0xff,0xff
-	};
-
-/******************************************************************
- * Init
- ******************************************************************/
-
-int isa_kbd_init (void)
-{
-	char *result;
-
-	result = kbd_initialize ();
-	if (result != NULL) {
-		result = kbd_initialize ();
-	}
-	if (result == NULL) {
-		printf ("AT Keyboard initialized\n");
-		irq_install_handler (KBD_INTERRUPT,
-				     (interrupt_handler_t *) kbd_interrupt,
-				     NULL);
-		return (1);
-	} else {
-		printf ("%s\n", result);
-		return (-1);
-	}
-}
-
-#ifdef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-extern int overwrite_console (void);
-#else
-int overwrite_console (void)
-{
-	return (0);
-}
-#endif
-
-int drv_isa_kbd_init (void)
-{
-	int error;
-	struct stdio_dev kbddev ;
-	char *stdinname  = getenv ("stdin");
-
-	if(isa_kbd_init() == -1)
-		return -1;
-	memset (&kbddev, 0, sizeof(kbddev));
-	strcpy(kbddev.name, DEVNAME);
-	kbddev.flags =  DEV_FLAGS_INPUT | DEV_FLAGS_SYSTEM;
-	kbddev.putc = NULL ;
-	kbddev.puts = NULL ;
-	kbddev.getc = kbd_getc ;
-	kbddev.tstc = kbd_testc ;
-
-	error = stdio_register (&kbddev);
-	if(error==0) {
-		/* check if this is the standard input device */
-		if(strcmp(stdinname,DEVNAME)==0) {
-			/* reassign the console */
-			if(overwrite_console()) {
-				return 1;
-			}
-			error=console_assign(stdin,DEVNAME);
-			if(error==0)
-				return 1;
-			else
-				return error;
-		}
-		return 1;
-	}
-	return error;
-}
-
-/******************************************************************
- * Queue handling
- ******************************************************************/
-/* puts character in the queue and sets up the in and out pointer */
-void kbd_put_queue(char data)
-{
-	if((in_pointer+1)==KBD_BUFFER_LEN) {
-		if(out_pointer==0) {
-			return; /* buffer full */
-		} else{
-			in_pointer=0;
-		}
-	} else {
-		if((in_pointer+1)==out_pointer)
-			return; /* buffer full */
-		in_pointer++;
-	}
-	kbd_buffer[in_pointer]=data;
-	return;
-}
-
-/* test if a character is in the queue */
-int kbd_testc(void)
-{
-	if(in_pointer==out_pointer)
-		return(0); /* no data */
-	else
-		return(1);
-}
-/* gets the character from the queue */
-int kbd_getc(void)
-{
-	char c;
-
-	while(in_pointer==out_pointer);
-	if((out_pointer+1)==KBD_BUFFER_LEN)
-		out_pointer=0;
-	else
-		out_pointer++;
-	c=kbd_buffer[out_pointer];
-	return (int)c;
-
-}
-
-/* set LEDs */
-
-void kbd_set_leds(void)
-{
-	if(caps_lock==0)
-		leds&=~LED_CAP; /* switch caps_lock off */
-	else
-		leds|=LED_CAP; /* switch on LED */
-	if(num_lock==0)
-		leds&=~LED_NUM; /* switch LED off */
-	else
-		leds|=LED_NUM;  /* switch on LED */
-	if(scroll_lock==0)
-		leds&=~LED_SCR; /* switch LED off */
-	else
-		leds|=LED_SCR; /* switch on LED */
-	kbd_send_data(KBD_CMD_SET_LEDS);
-	kbd_send_data(leds);
-}
-
-void handle_keyboard_event (unsigned char scancode)
-{
-	unsigned char keycode;
-
-	/*  Convert scancode to keycode */
-	PRINTF ("scancode %x\n", scancode);
-	if (scancode == 0xe0) {
-		e0 = 1;		/* special charakters */
-		return;
-	}
-	if (e0 == 1) {
-		e0 = 0;		/* delete flag */
-		if (!(((scancode & 0x7F) == 0x38) ||	/* the right ctrl key */
-		      ((scancode & 0x7F) == 0x1D) ||	/* the right alt key */
-		      ((scancode & 0x7F) == 0x35) ||	/* the right '/' key */
-		      ((scancode & 0x7F) == 0x1C) ||	/* the right enter key */
-		      ((scancode) == 0x48) ||	/* arrow up */
-		      ((scancode) == 0x50) ||	/* arrow down */
-		      ((scancode) == 0x4b) ||	/* arrow left */
-		      ((scancode) == 0x4d)))
-			/* arrow right */
-			/* we swallow unknown e0 codes */
-			return;
-	}
-	/* special cntrl keys */
-	switch (scancode) {
-	case 0x48:
-		kbd_put_queue (27);
-		kbd_put_queue (91);
-		kbd_put_queue ('A');
-		return;
-	case 0x50:
-		kbd_put_queue (27);
-		kbd_put_queue (91);
-		kbd_put_queue ('B');
-		return;
-	case 0x4b:
-		kbd_put_queue (27);
-		kbd_put_queue (91);
-		kbd_put_queue ('D');
-		return;
-	case 0x4D:
-		kbd_put_queue (27);
-		kbd_put_queue (91);
-		kbd_put_queue ('C');
-		return;
-	case 0x58:		/* F12 key */
-		if (ctrl == 1) {
-			extern int console_changed;
-
-			setenv ("stdin", DEVNAME);
-			setenv ("stdout", "vga");
-			console_changed = 1;
-		}
-		return;
-	case 0x2A:
-	case 0x36:		/* shift pressed */
-		shift = 1;
-		return;		/* do nothing else */
-	case 0xAA:
-	case 0xB6:		/* shift released */
-		shift = 0;
-		return;		/* do nothing else */
-	case 0x38:		/* alt pressed */
-		alt = 1;
-		return;		/* do nothing else */
-	case 0xB8:		/* alt released */
-		alt = 0;
-		return;		/* do nothing else */
-	case 0x1d:		/* ctrl pressed */
-		ctrl = 1;
-		return;		/* do nothing else */
-	case 0x9d:		/* ctrl released */
-		ctrl = 0;
-		return;		/* do nothing else */
-	case 0x46:		/* scrollock pressed */
-		scroll_lock = ~scroll_lock;
-		kbd_set_leds ();
-		return;		/* do nothing else */
-	case 0x3A:		/* capslock pressed */
-		caps_lock = ~caps_lock;
-		kbd_set_leds ();
-		return;
-	case 0x45:		/* numlock pressed */
-		num_lock = ~num_lock;
-		kbd_set_leds ();
-		return;
-	case 0xC6:		/* scroll lock released */
-	case 0xC5:		/* num lock released */
-	case 0xBA:		/* caps lock released */
-		return;		/* just swallow */
-	}
-	if ((scancode & 0x80) == 0x80)	/* key released */
-		return;
-	/* now, decide which table we need */
-	if (scancode > (sizeof (kbd_plain_xlate) / sizeof (kbd_plain_xlate[0]))) {	/* scancode not in list */
-		PRINTF ("unkown scancode %X\n", scancode);
-		return;		/* swallow it */
-	}
-	/* setup plain code first */
-	keycode = kbd_plain_xlate[scancode];
-	if (caps_lock == 1) {	/* caps_lock is pressed, overwrite plain code */
-		if (scancode > (sizeof (kbd_shift_xlate) / sizeof (kbd_shift_xlate[0]))) {	/* scancode not in list */
-			PRINTF ("unkown caps-locked scancode %X\n", scancode);
-			return;	/* swallow it */
-		}
-		keycode = kbd_shift_xlate[scancode];
-		if (keycode < 'A') {	/* we only want the alphas capital */
-			keycode = kbd_plain_xlate[scancode];
-		}
-	}
-	if (shift == 1) {	/* shift overwrites caps_lock */
-		if (scancode > (sizeof (kbd_shift_xlate) / sizeof (kbd_shift_xlate[0]))) {	/* scancode not in list */
-			PRINTF ("unkown shifted scancode %X\n", scancode);
-			return;	/* swallow it */
-		}
-		keycode = kbd_shift_xlate[scancode];
-	}
-	if (ctrl == 1) {	/* ctrl overwrites caps_lock and shift */
-		if (scancode > (sizeof (kbd_ctrl_xlate) / sizeof (kbd_ctrl_xlate[0]))) {	/* scancode not in list */
-			PRINTF ("unkown ctrl scancode %X\n", scancode);
-			return;	/* swallow it */
-		}
-		keycode = kbd_ctrl_xlate[scancode];
-	}
-	/* check if valid keycode */
-	if (keycode == 0xff) {
-		PRINTF ("unkown scancode %X\n", scancode);
-		return;		/* swallow unknown codes */
-	}
-
-	kbd_put_queue (keycode);
-	PRINTF ("%x\n", keycode);
-}
-
-/*
- * This reads the keyboard status port, and does the
- * appropriate action.
- *
- */
-unsigned char handle_kbd_event (void)
-{
-	unsigned char status = kbd_read_status ();
-	unsigned int work = 10000;
-
-	while ((--work > 0) && (status & KBD_STAT_OBF)) {
-		unsigned char scancode;
-
-		scancode = kbd_read_input ();
-
-		/* Error bytes must be ignored to make the
-		   Synaptics touchpads compaq use work */
-		/* Ignore error bytes */
-		if (!(status & (KBD_STAT_GTO | KBD_STAT_PERR))) {
-			if (status & KBD_STAT_MOUSE_OBF);	/* not supported: handle_mouse_event(scancode); */
-			else
-				handle_keyboard_event (scancode);
-		}
-		status = kbd_read_status ();
-	}
-	if (!work)
-		PRINTF ("pc_keyb: controller jammed (0x%02X).\n", status);
-	return status;
-}
-
-/******************************************************************************
- * Lowlevel Part of keyboard section
- */
-unsigned char kbd_read_status(void)
-{
-	return(in8(CONFIG_SYS_ISA_IO_BASE_ADDRESS + KDB_COMMAND_PORT));
-}
-
-unsigned char kbd_read_input(void)
-{
-	return(in8(CONFIG_SYS_ISA_IO_BASE_ADDRESS + KDB_DATA_PORT));
-}
-
-void kbd_write_command(unsigned char cmd)
-{
-	out8(CONFIG_SYS_ISA_IO_BASE_ADDRESS + KDB_COMMAND_PORT,cmd);
-}
-
-void kbd_write_output(unsigned char data)
-{
-	out8(CONFIG_SYS_ISA_IO_BASE_ADDRESS + KDB_DATA_PORT, data);
-}
-
-int kbd_read_data(void)
-{
-	int val;
-	unsigned char status;
-
-	val = -1;
-	status = kbd_read_status();
-	if (status & KBD_STAT_OBF) {
-		val = kbd_read_input();
-		if (status & (KBD_STAT_GTO | KBD_STAT_PERR))
-			val = -2;
-	}
-	return val;
-}
-
-int kbd_wait_for_input (void)
-{
-	unsigned long timeout;
-	int val;
-
-	timeout = KBD_TIMEOUT;
-	val = kbd_read_data ();
-	while (val < 0) {
-		if (timeout-- == 0)
-			return -1;
-		udelay (1000);
-		val = kbd_read_data ();
-	}
-	return val;
-}
-
-
-int kb_wait (void)
-{
-	unsigned long timeout = KBC_TIMEOUT * 10;
-
-	do {
-		unsigned char status = handle_kbd_event ();
-
-		if (!(status & KBD_STAT_IBF))
-			return 0;	/* ok */
-		udelay (1000);
-		timeout--;
-	} while (timeout);
-	return 1;
-}
-
-void kbd_write_command_w (int data)
-{
-	if (kb_wait ())
-		PRINTF ("timeout in kbd_write_command_w\n");
-	kbd_write_command (data);
-}
-
-void kbd_write_output_w (int data)
-{
-	if (kb_wait ())
-		PRINTF ("timeout in kbd_write_output_w\n");
-	kbd_write_output (data);
-}
-
-void kbd_send_data (unsigned char data)
-{
-	unsigned char status;
-
-	i8259_mask_irq (KBD_INTERRUPT);	/* disable interrupt */
-	kbd_write_output_w (data);
-	status = kbd_wait_for_input ();
-	if (status == KBD_REPLY_ACK)
-		i8259_unmask_irq (KBD_INTERRUPT);	/* enable interrupt */
-}
-
-
-char *kbd_initialize (void)
-{
-	int status;
-
-	in_pointer = 0;		/* delete in Buffer */
-	out_pointer = 0;
-	/*
-	 * Test the keyboard interface.
-	 * This seems to be the only way to get it going.
-	 * If the test is successful a x55 is placed in the input buffer.
-	 */
-	kbd_write_command_w (KBD_CCMD_SELF_TEST);
-	if (kbd_wait_for_input () != 0x55)
-		return "Kbd:   failed self test";
-	/*
-	 * Perform a keyboard interface test.  This causes the controller
-	 * to test the keyboard clock and data lines.  The results of the
-	 * test are placed in the input buffer.
-	 */
-	kbd_write_command_w (KBD_CCMD_KBD_TEST);
-	if (kbd_wait_for_input () != 0x00)
-		return "Kbd:   interface failed self test";
-	/*
-	 * Enable the keyboard by allowing the keyboard clock to run.
-	 */
-	kbd_write_command_w (KBD_CCMD_KBD_ENABLE);
-	status = kbd_wait_for_input ();
-	/*
-	 * Reset keyboard. If the read times out
-	 * then the assumption is that no keyboard is
-	 * plugged into the machine.
-	 * This defaults the keyboard to scan-code set 2.
-	 *
-	 * Set up to try again if the keyboard asks for RESEND.
-	 */
-	do {
-		kbd_write_output_w (KBD_CMD_RESET);
-		status = kbd_wait_for_input ();
-		if (status == KBD_REPLY_ACK)
-			break;
-		if (status != KBD_REPLY_RESEND) {
-			PRINTF ("status: %X\n", status);
-			return "Kbd:   reset failed, no ACK";
-		}
-	} while (1);
-	if (kbd_wait_for_input () != KBD_REPLY_POR)
-		return "Kbd:   reset failed, no POR";
-
-	/*
-	 * Set keyboard controller mode. During this, the keyboard should be
-	 * in the disabled state.
-	 *
-	 * Set up to try again if the keyboard asks for RESEND.
-	 */
-	do {
-		kbd_write_output_w (KBD_CMD_DISABLE);
-		status = kbd_wait_for_input ();
-		if (status == KBD_REPLY_ACK)
-			break;
-		if (status != KBD_REPLY_RESEND)
-			return "Kbd:   disable keyboard: no ACK";
-	} while (1);
-
-	kbd_write_command_w (KBD_CCMD_WRITE_MODE);
-	kbd_write_output_w (KBD_MODE_KBD_INT
-			    | KBD_MODE_SYS
-			    | KBD_MODE_DISABLE_MOUSE | KBD_MODE_KCC);
-
-	/* AMCC powerpc portables need this to use scan-code set 1 -- Cort */
-	kbd_write_command_w (KBD_CCMD_READ_MODE);
-	if (!(kbd_wait_for_input () & KBD_MODE_KCC)) {
-		/*
-		 * If the controller does not support conversion,
-		 * Set the keyboard to scan-code set 1.
-		 */
-		kbd_write_output_w (0xF0);
-		kbd_wait_for_input ();
-		kbd_write_output_w (0x01);
-		kbd_wait_for_input ();
-	}
-	kbd_write_output_w (KBD_CMD_ENABLE);
-	if (kbd_wait_for_input () != KBD_REPLY_ACK)
-		return "Kbd:   enable keyboard: no ACK";
-
-	/*
-	 * Finally, set the typematic rate to maximum.
-	 */
-	kbd_write_output_w (KBD_CMD_SET_RATE);
-	if (kbd_wait_for_input () != KBD_REPLY_ACK)
-		return "Kbd:   Set rate: no ACK";
-	kbd_write_output_w (0x00);
-	if (kbd_wait_for_input () != KBD_REPLY_ACK)
-		return "Kbd:   Set rate: no ACK";
-	return NULL;
-}
-
-void kbd_interrupt(void)
-{
-	handle_kbd_event();
-}
diff --git a/board/MAI/AmigaOneG3SE/ps2kbd.h b/board/MAI/AmigaOneG3SE/ps2kbd.h
deleted file mode 100644
index fc5c422..0000000
--- a/board/MAI/AmigaOneG3SE/ps2kbd.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * (C) Copyright 2002
- * John W. Linville, linville@tuxdriver.com
- *
- * Modified from code for support of MIP405 and PIP405 boards.  Previous
- * copyright follows.
- *
- * (C) Copyright 2001
- * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- */
-
-#ifndef _KBD_H_
-#define _KBD_H_
-
-extern int kbd_testc(void);
-extern int kbd_getc(void);
-extern void kbd_interrupt(void);
-extern char *kbd_initialize(void);
-
-unsigned char kbd_is_init(void);
-#define KBD_INTERRUPT 1
-#endif
diff --git a/board/MAI/AmigaOneG3SE/serial.c b/board/MAI/AmigaOneG3SE/serial.c
deleted file mode 100644
index 84a913e..0000000
--- a/board/MAI/AmigaOneG3SE/serial.c
+++ /dev/null
@@ -1,245 +0,0 @@
-#include <common.h>
-#include <ns16550.h>
-#include "short_types.h"
-#include "memio.h"
-#include "articiaS.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifndef CONFIG_SYS_NS16550
-static uint32 ComPort1;
-
-uint16 SerialEcho = 1;
-
-
-#define RECEIVER_HOLDING 0
-#define TRANSMITTER_HOLDING 0
-#define INTERRUPT_ENABLE 1
-#define INTERRUPT_STATUS 2
-#define FIFO_CONTROL 2
-#define LINE_CONTROL 3
-#define MODEM_CONTROL 4
-#define LINE_STATUS 5
-#define MODEM_STATUS 6
-#define SCRATCH_PAD 7
-
-#define DIVISOR_LATCH_LSB 0
-#define DIVISOR_LATCH_MSB 1
-#define PRESCALER_DIVISION 5
-
-#define COM_WRITE_BYTE(reg, byte) out_byte((ComPort1+reg), byte)
-#define COM_READ_BYTE(reg) in_byte((ComPort1+reg))
-
-static int serial_init_done = 0;
-
-void serial_init (void)
-{
-#if 0
-	uint32 clock_divisor = 115200 / baudrate;
-	uint8 cfg;
-	uint8 a;
-	uint16 devfn = 7 << 3;
-
-	if (serial_init_done)
-		return;
-
-	/*  Enter configuration mode */
-	cfg = pci_read_cfg_byte (0, devfn, 0x85);
-	pci_write_cfg_byte (0, devfn, 0x85, cfg | 0x02);
-
-	/* Set serial port COM1 as 3F8 */
-	out_byte (0x3F0, 0xE7);
-	out_byte (0x3f1, 0xfe);
-
-	/* Set serial port COM2 as 2F8 */
-	out_byte (0x3f0, 0xe8);
-	out_byte (0x3f1, 0xeb);
-
-	/* Enable */
-	out_byte (0x3f0, 0xe2);
-	a = in_byte (0x3f1);
-	a |= 0xc;
-	out_byte (0x3f0, 0xe2);
-	out_byte (0x3f1, a);
-
-	/*  Reset the configuration mode */
-	pci_write_cfg_byte (0, devfn, 0x85, cfg);
-#endif
-
-	ComPort1 = 0x3F8;
-
-	/*  Disable interrupts */
-	COM_WRITE_BYTE (INTERRUPT_ENABLE, 0x00);
-
-	/*  Set baud rate */
-	/* COM_WRITE_BYTE(LINE_CONTROL, 0x83); */
-	/* COM_WRITE_BYTE(DIVISOR_LATCH_LSB, (uint8)(clock_divisor & 0xFF)); */
-	/* COM_WRITE_BYTE(DIVISOR_LATCH_MSB, (uint8)(clock_divisor >> 8)); */
-	/* __asm__("eieio"); */
-
-	/*  Set 8-N-1 */
-	COM_WRITE_BYTE (LINE_CONTROL, 0x03);
-	__asm__ ("eieio");
-
-	/*  Disable FIFO */
-	COM_WRITE_BYTE (MODEM_CONTROL, 0x03);
-	COM_WRITE_BYTE (FIFO_CONTROL, 0x07);
-
-	__asm__ ("eieio");
-	serial_init_done = 1;
-}
-
-extern int console_changed;
-
-void serial_putc (const char sendme)
-{
-	if (sendme == '\n') {
-		while ((in_byte (0x3FD) & 0x40) == 0);
-		out_byte (0x3f8, 0x0D);
-	}
-
-	while ((in_byte (0x3FD) & 0x40) == 0);
-	out_byte (0x3f8, sendme);
-}
-
-int serial_getc (void)
-{
-#if 0
-	uint8 c;
-
-	for (;;) {
-		uint8 x = in_byte (0x3FD);
-
-		if (x & 0x01)
-			break;
-
-		if (x & 0x0C)
-			out_byte (0x3fd, 0x0c);
-	}
-
-	c = in_byte (0x3F8);
-
-	return c;
-#else
-	while ((in_byte (0x3FD) & 0x01) == 0) {
-		if (console_changed != 0) {
-			printf ("Console changed\n");
-			console_changed = 0;
-			return 0;
-		}
-	}
-	return in_byte (0x3F8);
-#endif
-}
-
-int serial_tstc (void)
-{
-	return (in_byte (0x03FD) & 0x01) != 0;
-}
-
-void serial_debug_putc (int c)
-{
-	serial_puts ("DBG");
-	serial_putc (c);
-	serial_putc (0x0d);
-	serial_putc (0x0A);
-}
-
-#else
-
-const NS16550_t Com0 = (NS16550_t) CONFIG_SYS_NS16550_COM1;
-const NS16550_t Com1 = (NS16550_t) CONFIG_SYS_NS16550_COM2;
-
-int serial_init (void)
-{
-	uint32 clock_divisor = 115200 / gd->baudrate;
-
-	NS16550_init (Com0, clock_divisor);
-	/* NS16550_reinit(Com1, clock_divisor); */
-	/* serial_puts("COM1: 3F8h initalized"); */
-
-	return (0);
-}
-
-#if 0
-void serial_putc (const char c)
-{
-	NS16550_putc (Com0, c);
-	if (c == '\n')
-		NS16550_putc (Com0, 0x0D);
-}
-
-int serial_getc (void)
-{
-	return (int) NS16550_getc (Com0);
-}
-
-int serial_tstc (void)
-{
-	return NS16550_tstc (Com0);
-}
-#else
-void serial_putc (const char sendme)
-{
-	if (sendme == '\n') {
-		while ((in_byte (0x3FD) & 0x40) == 0);
-		out_byte (0x3f8, 0x0D);
-	}
-
-	while ((in_byte (0x3FD) & 0x40) == 0);
-	out_byte (0x3f8, sendme);
-}
-
-
-extern int console_changed;
-
-int serial_getc (void)
-{
-#if 0
-	uint8 c;
-
-	for (;;) {
-		uint8 x = in_byte (0x3FD);
-
-		if (x & 0x01)
-			break;
-
-		if (x & 0x0C)
-			out_byte (0x3fd, 0x0c);
-	}
-
-	c = in_byte (0x3F8);
-
-	return c;
-#else
-	while ((in_byte (0x3FD) & 0x01) == 0) {
-		if (console_changed != 0) {
-			console_changed = 0;
-			return 0;
-		}
-	}
-
-	return in_byte (0x3F8);
-#endif
-}
-
-int serial_tstc (void)
-{
-	return (in_byte (0x03FD) & 0x01) != 0;
-}
-#endif
-
-#endif
-
-void serial_puts (const char *string)
-{
-	while (*string)
-		serial_putc (*string++);
-}
-
-void serial_setbrg (void)
-{
-	uint32 clock_divisor = 115200 / gd->baudrate;
-
-	NS16550_init (Com0, clock_divisor);
-}
diff --git a/board/MAI/AmigaOneG3SE/short_types.h b/board/MAI/AmigaOneG3SE/short_types.h
deleted file mode 100644
index 1840d28..0000000
--- a/board/MAI/AmigaOneG3SE/short_types.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * short type names
- *
- * (C) Copyright 2002
- * Hyperion Entertainment, ThomasF@hyperion-entertainment.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _SHORT_TYPES_H
-#define _SHORT_TYPES_H
-
-typedef unsigned long  uint32;
-typedef long           int32;
-typedef unsigned short uint16;
-typedef short          int16;
-typedef unsigned char  uint8;
-typedef signed char    int8;
-
-#endif
diff --git a/board/MAI/AmigaOneG3SE/smbus.c b/board/MAI/AmigaOneG3SE/smbus.c
deleted file mode 100644
index de13977..0000000
--- a/board/MAI/AmigaOneG3SE/smbus.c
+++ /dev/null
@@ -1,206 +0,0 @@
-#include "memio.h"
-#include "articiaS.h"
-
-#ifndef FALSE
-#define FALSE 0
-#endif
-
-#ifndef TRUE
-#define TRUE 1
-#endif
-
-
-void sm_write_mode(void)
-{
-    out_byte(0xA539, 0x00);
-    out_byte(0xA53A, 0x03);
-}
-
-void sm_read_mode(void)
-{
-    out_byte(0xA53A, 0x02);
-    out_byte(0xA539, 0x02);
-}
-
-void sm_write_byte(uint8 writeme)
-{
-    int i;
-    int level;
-
-    out_byte(0xA539, 0x00);
-
-    level = 0;
-
-    for (i=0; i<8; i++)
-    {
-	if ((writeme & 0x80) == (level<<7))
-	{
-	    /* Bit did not change, rewrite strobe */
-	    out_byte(0xA539, level | 0x02);
-	    out_byte(0xA539, level);
-	}
-	else
-	{
-	    /* Bit changed, set bit, then strobe */
-	    level = (writeme & 0x80) >> 7;
-	    out_byte(0xA539, level);
-	    out_byte(0xA539, level | 0x02);
-	    out_byte(0xA539, level);
-	}
-	writeme <<= 1;
-    }
-    out_byte(0xA539, 0x00);
-}
-
-uint8 sm_read_byte(void)
-{
-    uint8 retme, r;
-    int i;
-
-    retme = 0;
-    for (i=0; i<8; i++)
-    {
-	retme <<= 1;
-	out_byte(0xA539, 0x00);
-	out_byte(0xA539, 0x02);
-	r = in_byte(0xA538) & 0x01;
-	retme |= r;
-    }
-
-    return retme;
-}
-
-int sm_get_ack(void)
-{
-    uint8 r;
-    r = in_byte(0xA538);
-    if ((r&0x01) == 0) return TRUE;
-    else return FALSE;
-}
-
-void sm_write_ack(void)
-{
-    out_byte(0xA539, 0x00);
-    out_byte(0xA539, 0x02);
-    out_byte(0xA539, 0x00);
-}
-
-void sm_write_nack(void)
-{
-    out_byte(0xA539, 0x01);
-    out_byte(0xA539, 0x03);
-    out_byte(0xA539, 0x01);
-}
-
-void sm_send_start(void)
-{
-    out_byte(0xA539, 0x03);
-    out_byte(0xA539, 0x02);
-}
-
-void sm_send_stop(void)
-{
-    out_byte(0xA539, 0x02);
-    out_byte(0xA539, 0x03);
-}
-
-int sm_read_byte_from_device(uint8 addr, uint8 reg, uint8 *storage)
-{
-    /* S Addr Wr */
-    sm_write_mode();
-    sm_send_start();
-    sm_write_byte((addr<<1));
-
-    /* [A] */
-    sm_read_mode();
-    if (sm_get_ack() == FALSE) return FALSE;
-
-    /* Comm */
-    sm_write_mode();
-    sm_write_byte(reg);
-
-    /* [A] */
-    sm_read_mode();
-    if (sm_get_ack() == FALSE) return FALSE;
-
-    /* S Addr Rd */
-    sm_write_mode();
-    sm_send_start();
-    sm_write_byte((addr<<1)|1);
-
-    /* [A] */
-    sm_read_mode();
-    if (sm_get_ack() == FALSE) return FALSE;
-
-    /* [Data] */
-    *storage = sm_read_byte();
-
-    /* NA */
-    sm_write_mode();
-    sm_write_nack();
-    sm_send_stop();
-
-    return TRUE;
-}
-
-void sm_init(void)
-{
-    /* Switch to PMC mode */
-    pci_write_cfg_byte(0, 0, REG_GROUP, (uint8)(REG_GROUP_SPECIAL|REG_GROUP_POWER));
-
-    /* Set GPIO Base */
-    pci_write_cfg_long(0, 0, 0x40, 0xa500);
-
-    /* Enable GPIO */
-    pci_write_cfg_byte(0, 0, 0x44, 0x11);
-
-    /* Set both GPIO 0 and 1 as output */
-    out_byte(0xA53A, 0x03);
-}
-
-
-void sm_term(void)
-{
-    /* Switch to normal mode */
-    pci_write_cfg_byte(0, 0, REG_GROUP, 0);
-}
-
-
-int sm_get_data(uint8 *DataArray, int dimm_socket)
-{
-    int j;
-
-#if 0
-    /* Switch to PMC mode */
-    pci_write_cfg_byte(0, 0, REG_GROUP, (uint8)(REG_GROUP_SPECIAL|REG_GROUP_POWER));
-
-    /* Set GPIO Base */
-    pci_write_cfg_long(0, 0, 0x40, 0xa500);
-
-    /* Enable GPIO */
-    pci_write_cfg_byte(0, 0, 0x44, 0x11);
-
-    /* Set both GPIO 0 and 1 as output */
-    out_byte(0xA53A, 0x03);
-#endif
-
-    sm_init();
-    /* Start reading the rom */
-
-    j = 0;
-
-    do
-    {
-	if (sm_read_byte_from_device(dimm_socket, (uint8)j, DataArray) == FALSE)
-	{
-	    sm_term();
-	    return FALSE;
-	}
-
-	DataArray++;
-	j++;
-    } while (j < 128);
-
-    sm_term();
-    return TRUE;
-}
diff --git a/board/MAI/AmigaOneG3SE/smbus.h b/board/MAI/AmigaOneG3SE/smbus.h
deleted file mode 100644
index beeb6a0..0000000
--- a/board/MAI/AmigaOneG3SE/smbus.h
+++ /dev/null
@@ -1,22 +0,0 @@
-#ifndef _SMBUS_H_
-#define _SMBUS_H_
-
-#include "short_types.h"
-
-#define SM_DIMM0_ADDR 0x51
-#define SM_DIMM1_ADDR 0x52
-
-void sm_write_mode(void);
-void sm_read_mode(void);
-void sm_write_byte(uint8 writeme);
-uint8 sm_read_byte(void);
-int sm_get_ack(void);
-void sm_write_ack(void);
-void sm_write_nack(void);
-void sm_send_start(void);
-void sm_send_stop(void);
-int sm_read_byte_from_device(uint8 addr, uint8 reg, uint8 *storage);
-int sm_get_data(uint8 *DataArray, int dimm_socket);
-void sm_init(void);
-void sm_term(void);
-#endif
diff --git a/board/MAI/AmigaOneG3SE/start.txt b/board/MAI/AmigaOneG3SE/start.txt
deleted file mode 100644
index 2526ed2..0000000
--- a/board/MAI/AmigaOneG3SE/start.txt
+++ /dev/null
@@ -1,198 +0,0 @@
-
-	/*------------------------------------------------------*/
-	/*              TERON Articia / SDRAM Init              */
-	/*------------------------------------------------------*/
-
-*       XD_CTL  = 0x81000000			(0x74)
-
-*       HBUS_ACC_CTL_0 &= 0xFFFFFDFF		(0x5c)
-		       /* host bus access ctl reg 2(5e) */
-		       /* set - CPU read from memory data one clock after data is latched */
-
-*       GLOBL_INFO_0 |= 0x00004000		(0x50)
-		      /* global info register 2 (52), AGP/PCI bus 1 arbiter is addressed in Articia S */
-
-	PCI_1_SB_CONFIG_0 |= 0x00000400         (0x80d0)
-			/* PCI1 side band config reg 2 (d2), enable read acces while write buffer not empty */
-
-	MEM_RAS_CTL_0 |= 0x3f000000		(0xcc)
-		      &= 0x3fffffff
-		      /* RAS park control reg 0(cc), park access enable is set */
-
-	HOST_RDBUF_CTL |= 0x10000000		(0x70)
-		       &= 0x10ffffff
-		      /* host read buffer control reg, enable prefetch for CPU read from DRAM control */
-
-	HBUS_ACC_CTL_0 |= 0x0100001f		(0x5c)
-		       &= 0xf1ffffff
-		      /* host bus access control register, enable CPU address bus pipe control	*/
-		      /* two outstanding requests,  *** changed to 2 from 3				*/
-		      /* enable line merge write control for CPU write to system memory, PCI 1	*/
-		      /* and PCI 0 bus memory; enable page merge write control for write to		*/
-		      /* PCI bus 0 & bus 1 memory							*/
-
-	SRAM_CTL |= 0x00004000			(0xc8)
-		 &= 0xffbff7ff
-		      /* DRAM detail timing control register 1 (ca), bit 3 set to 0	*/
-		      /* DRAM start access latency control - wait for one clock	*/
-		      /* ff9f changed to ffbf						*/
-
-	DIM0_TIM_CTL_0 = 0x737d737d             (0xc9)
-		      /* DRAM timing control for dimm0 & dimm1; set wait one clock	*/
-		      /* cycle for next data access					*/
-
-	DIM2_TIM_CTL_0 = 0x737d737d             (0xca)
-		      /* DRAM timing control for dimm2 & dimm3; set wait one clock	*/
-		      /* cycle for next data access					*/
-
-	DIM0_BNK0_CTL_0 = BNK0_RAM_SIZ_128MB    (0x90)
-		      /* set dimm0 bank0 for 128 MB	*/
-
-	DIM0_BNK1_CTL_0 = BNK1_RAM_SIZ_128MB    (0x94)
-		      /* set dimm0 for  bank1		*/
-
-	DIM0_TIM_CTL_0 = 0xf3bf0000             (0xc9)
-		      /* dimm0 timing control register; RAS - CAS latency - 4 clock		*/
-		      /* CAS access latency - 3 wait; pre-charge latency - 3 wait		*/
-		      /* pre-charge command period control - 5 clock; wait one clock		*/
-		      /* cycle for next data access; read to write access latency control	*/
-		      /* - 2 clock cycles							*/
-
-	DRAM_GBL_CTL_0 |= 0x00000100            (0xc0)
-		       &= 0xffff01ff
-		      /* memory global control register - support buffer sdram on bank 0	*/
-
-	DRAM_ECC_CTL_0 |= 0x00260000		(0xc4)
-		       &= 0xff26ffff
-		      /* enable ECC; enable read, modify, write control	*/
-
-	DRAM_REF_CTL_0 = DRAM_REF_DATA          (0xb8)
-		      /* set DRAM refresh parameters *** changed to 00940100	*/
-
-	nop
-	nop
-	nop
-	nop
-	nop
-
-	DRAM_ECC_CTL_0 |= 0x20243280		(0xc4)
-		      /* turn off ecc		*/
-		      /* for SDRAM bank 0	*/
-
-	DRAM_ECC_CTL_0 |= 0x20243290            (0xc4) ?
-		      /* for SDRAM bank 1	*/
-
-
-/* Additional Stuff...*/
-
-	GLOBL_CTRL |= 0x20000b00		(0x54)
-
-	PCI_0_SB_CONFIG |= 0x04100007		(0xd0)
-		      /* PCI 0 Side band config reg*/
-
-	0x8000083c |= 0x00080000
-		      /* Disable VGA decode on PCI Bus 1 */
-
-
-/*End Additional Stuff..*/
-
-	/*--------------------------------------------------------------*/
-	/*              TERON serial port initialization code           */
-	/*--------------------------------------------------------------*/
-
-	0x84380080 |= 0x00030000
-		     /* enable super IO configuration VIA chip Register 85	*/
-		     /* Enable super I/O config mode */
-
-	0xfe0003f0 = 0xe2
-	bl delay1
-
-	0xfe0003f1 = 0x0f
-	bl delay1
-		    /* enable com1 & com2, parallel port disabled */
-
-	0xfe0003f0 = 0xe7
-	bl delay1
-		    /* let's make com1 base as 0x3f8 */
-
-	0xfe0003f1 = 0xfe
-	bl delay1
-
-	0xfe0003f0 = 0xe8
-	bl delay1
-		    /* let's make com2 base as 0x2f8 */
-
-	0xfe0003f1 = 0xbe
-
-	0x84380080 &= 0xfffdffff
-		    /* closing super IO configuration VIA chip Register 85   */
-
-
-/* -------------------------------*/
-
-	0xfe0003fb = 0x83
-	bl delay1
-		   /*latch enable word length -8 bit */         /* set mslab bit	*/
-	0xfe0003f8 = 0x0c
-	bl delay1
-		   /* set baud rate lsb for 9600 baud	*/
-	0xfe0003f9 = 0x0
-	bl delay1
-		   /* set baud rate msb for 9600 baud	*/
-	0xfe0003fb  = 0x03
-	bl delay1
-		      /* reset mslab	*/
-
-	/*--------------------------------------------------------------*/
-	/*              END TERON Serial Port Initialization Code       */
-	/*--------------------------------------------------------------*/
-
-
-	/*--------------------------------------------------------------*/
-	/*      END TERON Articia / SDRAM Initialization code           */
-	/*--------------------------------------------------------------*/
-
-Proposed from Documentation:
-
-write dmem 0xfec00cf8 0x50000080
-write dmem 0xfee00cfc 0xc0305411
-
-      Writes to index 0x50-0x53.
-      0x50: Global Information Register 0
-	    0xC0 = Little Endian CPU, Sequential order Burst
-      0x51: Global Information Register 1
-	    Read only, 0x30 = Provides PowerPC and X86 support
-      0x52: Global Information Register 2
-	    0x05 = 64/128 bit CPU bus support
-      0x53: Global Information Register 3
-	    0x80 = PCI Bus 0 grant active time is 1 clock after REQ# deasserted
-
-write dmem 0xfec00cf8 0x5c000080
-write dmem 0xfee00cfc 0xb300011F
-
-write dmem 0xfec00cf8 0xc8000080
-write dmem 0xfee00cfc 0x0020f100
-
-write dmem 0xfec00cf8 0x90000080
-write dmem 0xfee00cfc 0x007fe700
-
-write dmem 0xfec00cf8 0x9400080
-write dmem 0xfee00cfc 0x007fe700
-
-write dmem 0xfec00cf8 0xb0000080
-write dmem 0xfee00cfc 0x737d737d
-
-write dmem 0xfec00cf8 0xb4000080
-write dmem 0xfee00cfc 0x737d737d
-
-write dmem 0xfec00cf8 0xc0000080
-write dmem 0xfee00cfc 0x40005500
-
-write dmem 0xfec00cf8 0xb8000080
-write dmem 0xfee00cfc 0x00940100
-
-write dmem 0xfec00cf8 0xc4000080
-write dmem 0xfee00cfc 0x00003280
-
-write dmem 0xfec00cf8 0xc4000080
-write dmem 0xfee00cfc 0x00003290
diff --git a/board/MAI/AmigaOneG3SE/todo.txt b/board/MAI/AmigaOneG3SE/todo.txt
deleted file mode 100644
index df25e3d..0000000
--- a/board/MAI/AmigaOneG3SE/todo.txt
+++ /dev/null
@@ -1,3 +0,0 @@
-- Init interrupt controller
-- init sdram
-- init ide controller
\ No newline at end of file
diff --git a/board/MAI/AmigaOneG3SE/u-boot.lds b/board/MAI/AmigaOneG3SE/u-boot.lds
deleted file mode 100644
index e86ac56..0000000
--- a/board/MAI/AmigaOneG3SE/u-boot.lds
+++ /dev/null
@@ -1,136 +0,0 @@
-/*
- * (C) Copyright 2001
- * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
- *
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * u-boot.lds - linker script for U-Boot on the AmigaOneG3SE Board.
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
-   __DYNAMIC = 0;    */
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .interp : { *(.interp) }
-  .hash          : { *(.hash)		}
-  .dynsym        : { *(.dynsym)		}
-  .dynstr        : { *(.dynstr)		}
-  .rel.text      : { *(.rel.text)		}
-  .rela.text     : { *(.rela.text)	}
-  .rel.data      : { *(.rel.data)		}
-  .rela.data     : { *(.rela.data)	}
-  .rel.rodata    : { *(.rel.rodata)	}
-  .rela.rodata   : { *(.rela.rodata)	}
-  .rel.got       : { *(.rel.got)		}
-  .rela.got      : { *(.rela.got)		}
-  .rel.ctors     : { *(.rel.ctors)	}
-  .rela.ctors    : { *(.rela.ctors)	}
-  .rel.dtors     : { *(.rel.dtors)	}
-  .rela.dtors    : { *(.rela.dtors)	}
-  .rel.bss       : { *(.rel.bss)		}
-  .rela.bss      : { *(.rela.bss)		}
-  .rel.plt       : { *(.rel.plt)		}
-  .rela.plt      : { *(.rela.plt)		}
-  .init          : { *(.init)	}
-  .plt : { *(.plt) }
-  .text      :
-  {
-    arch/powerpc/cpu/74xx_7xx/start.o	(.text)
-/* store the environment in a seperate sector in the boot flash */
-/*    . = env_offset; */
-    common/env_embedded.o(.text)
-
-    *(.text)
-    *(.got1)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(.eh_frame)
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-  .fini      : { *(.fini)    } =0
-  .ctors     : { *(.ctors)   }
-  .dtors     : { *(.dtors)   }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    *(.got)
-    _GOT2_TABLE_ = .;
-    *(.got2)
-    _FIXUP_TABLE_ = .;
-    *(.fixup)
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data)
-    *(.data1)
-    *(.sdata)
-    *(.sdata2)
-    *(.dynamic)
-    CONSTRUCTORS
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
-
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.sbss) *(.scommon)
-   *(.dynbss)
-   *(.bss)
-   *(COMMON)
-  }
-  _end = ALIGN(4) /*.*/ ;
-  PROVIDE (end = ALIGN(4) /*.*/);
-}
diff --git a/board/MAI/AmigaOneG3SE/usb_uhci.c b/board/MAI/AmigaOneG3SE/usb_uhci.c
deleted file mode 100644
index 857ab3e..0000000
--- a/board/MAI/AmigaOneG3SE/usb_uhci.c
+++ /dev/null
@@ -1,1178 +0,0 @@
-/*
- * (C) Copyright 2001
- * Denis Peter, MPL AG Switzerland
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Note: Part of this code has been derived from linux
- *
- */
-
-/**********************************************************************
- * How it works:
- * -------------
- * The framelist / Transfer descriptor / Queue Heads are similar like
- * in the linux usb_uhci.c.
- *
- * During initialization, the following skeleton is allocated in init_skel:
- *
- *         framespecific           |           common chain
- *
- * framelist[]
- * [  0 ]-----> TD ---------\
- * [  1 ]-----> TD ----------> TD ------> QH -------> QH -------> QH ---> NULL
- *   ...        TD ---------/
- * [1023]-----> TD --------/
- *
- *              ^^             ^^         ^^          ^^          ^^
- *              7 TDs for      1 TD for   Start of    Start of    End Chain
- *              INT (2-128ms)  1ms-INT    CTRL Chain  BULK Chain
- *
- *
- * Since this is a bootloader, the isochronous transfer descriptor have been removed.
- *
- * Interrupt Transfers.
- * --------------------
- * For Interupt transfers USB_MAX_TEMP_INT_TD Transfer descriptor are available. They
- * will be inserted after the appropriate (depending the interval setting) skeleton TD.
- * If an interrupt has been detected the dev->irqhandler is called. The status and number
- * of transfered bytes is stored in dev->irq_status resp. dev->irq_act_len. If the
- * dev->irqhandler returns 0, the interrupt TD is removed and disabled. If an 1 is returned,
- * the interrupt TD will be reactivated.
- *
- * Control Transfers
- * -----------------
- * Control Transfers are issued by filling the tmp_td with the appropriate data and connect
- * them to the qh_cntrl queue header. Before other control/bulk transfers can be issued,
- * the programm has to wait for completion. This does not allows asynchronous data transfer.
- *
- * Bulk Transfers
- * --------------
- * Bulk Transfers are issued by filling the tmp_td with the appropriate data and connect
- * them to the qh_bulk queue header. Before other control/bulk transfers can be issued,
- * the programm has to wait for completion. This does not allows asynchronous data transfer.
- *
- *
- */
-
-#include <common.h>
-#include <pci.h>
-
-#ifdef CONFIG_USB_UHCI
-
-#include <usb.h>
-#include "usb_uhci.h"
-
-#define USB_MAX_TEMP_TD      128  /* number of temporary TDs for bulk and control transfers */
-#define USB_MAX_TEMP_INT_TD  32   /* number of temporary TDs for Interrupt transfers */
-
-
-/*#define USB_UHCI_DEBUG */
-
-#ifdef	USB_UHCI_DEBUG
-#define	USB_UHCI_PRINTF(fmt,args...)	printf (fmt ,##args)
-#else
-#define USB_UHCI_PRINTF(fmt,args...)
-#endif
-
-
-static int irqvec = -1;            /* irq vector, if -1 uhci is stopped / reseted */
-unsigned int usb_base_addr;       /* base address */
-
-static uhci_td_t td_int[8];        /* Interrupt Transfer descriptors */
-static uhci_qh_t qh_cntrl;         /* control Queue Head */
-static uhci_qh_t qh_bulk;          /*  bulk Queue Head */
-static uhci_qh_t qh_end;           /* end Queue Head */
-static uhci_td_t td_last;          /* last TD (linked with end chain) */
-
-/* temporary tds */
-static uhci_td_t tmp_td[USB_MAX_TEMP_TD];          /* temporary bulk/control td's  */
-static uhci_td_t tmp_int_td[USB_MAX_TEMP_INT_TD];  /* temporary interrupt td's  */
-
-static unsigned long framelist[1024] __attribute__ ((aligned (0x1000))); /* frame list */
-
-static struct virt_root_hub rh;   /* struct for root hub */
-
-/**********************************************************************
- * some forward decleration
- */
-int uhci_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
-						void *buffer, int transfer_len,struct devrequest *setup);
-
-/* fill a td with the approproiate data. Link, status, info and buffer
- * are used by the USB controller itselfes, dev is used to identify the
- * "connected" device
- */
-void usb_fill_td(uhci_td_t* td,unsigned long link,unsigned long status,
-					unsigned long info, unsigned long buffer, unsigned long dev)
-{
-	td->link=swap_32(link);
-	td->status=swap_32(status);
-	td->info=swap_32(info);
-	td->buffer=swap_32(buffer);
-	td->dev_ptr=dev;
-}
-
-/* fill a qh with the approproiate data. Head and element are used by the USB controller
- * itselfes. As soon as a valid dev_ptr is filled, a td chain is connected to the qh.
- * Please note, that after completion of the td chain, the entry element is removed /
- * marked invalid by the USB controller.
- */
-void usb_fill_qh(uhci_qh_t* qh,unsigned long head,unsigned long element)
-{
-	qh->head=swap_32(head);
-	qh->element=swap_32(element);
-	qh->dev_ptr=0L;
-}
-
-/* get the status of a td->status
- */
-unsigned long usb_uhci_td_stat(unsigned long status)
-{
-	unsigned long result=0;
-	result |= (status & TD_CTRL_NAK)      ? USB_ST_NAK_REC : 0;
-	result |= (status & TD_CTRL_STALLED)  ? USB_ST_STALLED : 0;
-	result |= (status & TD_CTRL_DBUFERR)  ? USB_ST_BUF_ERR : 0;
-	result |= (status & TD_CTRL_BABBLE)   ? USB_ST_BABBLE_DET : 0;
-	result |= (status & TD_CTRL_CRCTIMEO) ? USB_ST_CRC_ERR : 0;
-	result |= (status & TD_CTRL_BITSTUFF) ? USB_ST_BIT_ERR : 0;
-	result |= (status & TD_CTRL_ACTIVE)   ? USB_ST_NOT_PROC : 0;
-	return result;
-}
-
-/* get the status and the transfered len of a td chain.
- * called from the completion handler
- */
-int usb_get_td_status(uhci_td_t *td,struct usb_device *dev)
-{
-	unsigned long temp,info;
-	unsigned long stat;
-	uhci_td_t *mytd=td;
-
-	if(dev->devnum==rh.devnum)
-		return 0;
-	dev->act_len=0;
-	stat=0;
-	do {
-		temp=swap_32((unsigned long)mytd->status);
-		stat=usb_uhci_td_stat(temp);
-		info=swap_32((unsigned long)mytd->info);
-		if(((info & 0xff)!= USB_PID_SETUP) &&
-				(((info >> 21) & 0x7ff)!= 0x7ff) &&
-				(temp & 0x7FF)!=0x7ff)
-		{  /* if not setup and not null data pack */
-			dev->act_len+=(temp & 0x7FF) + 1; /* the transfered len is act_len + 1 */
-		}
-		if(stat) {           /* status no ok */
-			dev->status=stat;
-			return -1;
-		}
-		temp=swap_32((unsigned long)mytd->link);
-		mytd=(uhci_td_t *)(temp & 0xfffffff0);
-	}while((temp & 0x1)==0); /* process all TDs */
-	dev->status=stat;
-	return 0; /* Ok */
-}
-
-
-/*-------------------------------------------------------------------
- *                         LOW LEVEL STUFF
- *          assembles QHs und TDs for control, bulk and iso
- *-------------------------------------------------------------------*/
-
-/* Submits a control message. That is a Setup, Data and Status transfer.
- * Routine does not wait for completion.
- */
-int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
-										int transfer_len,struct devrequest *setup)
-{
-	unsigned long destination, status;
-	int maxsze = usb_maxpacket(dev, pipe);
-	unsigned long dataptr;
-	int len;
-	int pktsze;
-	int i=0;
-
-	if (!maxsze) {
-		USB_UHCI_PRINTF("uhci_submit_control_urb: pipesize for pipe %lx is zero\n", pipe);
-		return -1;
-	}
-	if(((pipe>>8)&0x7f)==rh.devnum) {
-		/* this is the root hub -> redirect it */
-		return uhci_submit_rh_msg(dev,pipe,buffer,transfer_len,setup);
-	}
-	USB_UHCI_PRINTF("uhci_submit_control start len %x, maxsize %x\n",transfer_len,maxsze);
-	/* The "pipe" thing contains the destination in bits 8--18 */
-	destination = (pipe & PIPE_DEVEP_MASK) | USB_PID_SETUP; /* Setup stage */
-	/* 3 errors */
-	status = (pipe & TD_CTRL_LS) | TD_CTRL_ACTIVE | (3 << 27);
-	/* (urb->transfer_flags & USB_DISABLE_SPD ? 0 : TD_CTRL_SPD); */
-	/*  Build the TD for the control request, try forever, 8 bytes of data */
-	usb_fill_td(&tmp_td[i],UHCI_PTR_TERM ,status, destination | (7 << 21),(unsigned long)setup,(unsigned long)dev);
-#if 0
-	{
-		char *sp=(char *)setup;
-		printf("SETUP to pipe %lx: %x %x %x %x %x %x %x %x\n", pipe,
-		    sp[0],sp[1],sp[2],sp[3],sp[4],sp[5],sp[6],sp[7]);
-	}
-#endif
-	dataptr = (unsigned long)buffer;
-	len=transfer_len;
-
-	/* If direction is "send", change the frame from SETUP (0x2D)
-	   to OUT (0xE1). Else change it from SETUP to IN (0x69). */
-	destination = (pipe & PIPE_DEVEP_MASK) | ((pipe & USB_DIR_IN)==0 ? USB_PID_OUT : USB_PID_IN);
-	while (len > 0) {
-		/* data stage */
-		pktsze = len;
-		i++;
-		if (pktsze > maxsze)
-			pktsze = maxsze;
-		destination ^= 1 << TD_TOKEN_TOGGLE;	/* toggle DATA0/1 */
-		usb_fill_td(&tmp_td[i],UHCI_PTR_TERM, status, destination | ((pktsze - 1) << 21),dataptr,(unsigned long)dev);	/* Status, pktsze bytes of data */
-		tmp_td[i-1].link=swap_32((unsigned long)&tmp_td[i]);
-
-		dataptr += pktsze;
-		len -= pktsze;
-	}
-
-	/*  Build the final TD for control status */
-	/* It's only IN if the pipe is out AND we aren't expecting data */
-
-	destination &= ~UHCI_PID;
-	if (((pipe & USB_DIR_IN)==0) || (transfer_len == 0))
-		destination |= USB_PID_IN;
-	else
-		destination |= USB_PID_OUT;
-	destination |= 1 << TD_TOKEN_TOGGLE;	/* End in Data1 */
-	i++;
-	status &=~TD_CTRL_SPD;
-	/* no limit on errors on final packet , 0 bytes of data */
-	usb_fill_td(&tmp_td[i],UHCI_PTR_TERM, status | TD_CTRL_IOC, destination | (UHCI_NULL_DATA_SIZE << 21),0,(unsigned long)dev);
-	tmp_td[i-1].link=swap_32((unsigned long)&tmp_td[i]);	/* queue status td */
-	/*	usb_show_td(i+1);*/
-	USB_UHCI_PRINTF("uhci_submit_control end (%d tmp_tds used)\n",i);
-	/* first mark the control QH element terminated */
-	qh_cntrl.element=0xffffffffL;
-	/* set qh active */
-	qh_cntrl.dev_ptr=(unsigned long)dev;
-	/* fill in tmp_td_chain */
-	qh_cntrl.element=swap_32((unsigned long)&tmp_td[0]);
-	return 0;
-}
-
-/*-------------------------------------------------------------------
- * Prepare TDs for bulk transfers.
- */
-int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,int transfer_len)
-{
-	unsigned long destination, status,info;
-	unsigned long dataptr;
-	int maxsze = usb_maxpacket(dev, pipe);
-	int len;
-	int i=0;
-
-	if(transfer_len < 0) {
-		printf("Negative transfer length in submit_bulk\n");
-		return -1;
-	}
-	if (!maxsze)
-		return -1;
-	/* The "pipe" thing contains the destination in bits 8--18. */
-	destination = (pipe & PIPE_DEVEP_MASK) | usb_packetid (pipe);
-	/* 3 errors */
-	status = (pipe & TD_CTRL_LS) | TD_CTRL_ACTIVE | (3 << 27);
-	/*	((urb->transfer_flags & USB_DISABLE_SPD) ? 0 : TD_CTRL_SPD) | (3 << 27); */
-	/* Build the TDs for the bulk request */
-	len = transfer_len;
-	dataptr = (unsigned long)buffer;
-	do {
-		int pktsze = len;
-		if (pktsze > maxsze)
-			pktsze = maxsze;
-		/* pktsze bytes of data  */
-		info = destination | (((pktsze - 1)&UHCI_NULL_DATA_SIZE) << 21) |
-			(usb_gettoggle (dev, usb_pipeendpoint (pipe), usb_pipeout (pipe)) << TD_TOKEN_TOGGLE);
-
-		if((len-pktsze)==0)
-			status |= TD_CTRL_IOC;	/* last one generates INT */
-
-		usb_fill_td(&tmp_td[i],UHCI_PTR_TERM, status, info,dataptr,(unsigned long)dev);	/* Status, pktsze bytes of data */
-		if(i>0)
-			tmp_td[i-1].link=swap_32((unsigned long)&tmp_td[i]);
-		i++;
-		dataptr += pktsze;
-		len -= pktsze;
-		usb_dotoggle (dev, usb_pipeendpoint (pipe), usb_pipeout (pipe));
-	} while (len > 0);
-	/* first mark the bulk QH element terminated */
-	qh_bulk.element=0xffffffffL;
-	/* set qh active */
-	qh_bulk.dev_ptr=(unsigned long)dev;
-	/* fill in tmp_td_chain */
-	qh_bulk.element=swap_32((unsigned long)&tmp_td[0]);
-	return 0;
-}
-
-
-/* search a free interrupt td
- */
-uhci_td_t *uhci_alloc_int_td(void)
-{
-	int i;
-	for(i=0;i<USB_MAX_TEMP_INT_TD;i++) {
-		if(tmp_int_td[i].dev_ptr==0) /* no device assigned -> free TD */
-			return &tmp_int_td[i];
-	}
-	return NULL;
-}
-
-#if 0
-void uhci_show_temp_int_td(void)
-{
-	int i;
-	for(i=0;i<USB_MAX_TEMP_INT_TD;i++) {
-		if((tmp_int_td[i].dev_ptr&0x01)!=0x1L) /* no device assigned -> free TD */
-			printf("temp_td %d is assigned to dev %lx\n",i,tmp_int_td[i].dev_ptr);
-	}
-	printf("all others temp_tds are free\n");
-}
-#endif
-/*-------------------------------------------------------------------
- * submits USB interrupt (ie. polling ;-)
- */
-int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,int transfer_len, int interval)
-{
-	int nint, n;
-	unsigned long status, destination;
-	unsigned long info,tmp;
-	uhci_td_t *mytd;
-	if (interval < 0 || interval >= 256)
-		return -1;
-
-	if (interval == 0)
-		nint = 0;
-	else {
-		for (nint = 0, n = 1; nint <= 8; nint++, n += n)	/* round interval down to 2^n */
-		 {
-			if(interval < n) {
-				interval = n / 2;
-				break;
-			}
-		}
-		nint--;
-	}
-
-	USB_UHCI_PRINTF("Rounded interval to %i, chain  %i\n", interval, nint);
-	mytd=uhci_alloc_int_td();
-	if(mytd==NULL) {
-		printf("No free INT TDs found\n");
-		return -1;
-	}
-	status = (pipe & TD_CTRL_LS) | TD_CTRL_ACTIVE | TD_CTRL_IOC | (3 << 27);
-/*		(urb->transfer_flags & USB_DISABLE_SPD ? 0 : TD_CTRL_SPD) | (3 << 27);
-*/
-
-	destination =(pipe & PIPE_DEVEP_MASK) | usb_packetid (pipe) | (((transfer_len - 1) & 0x7ff) << 21);
-
-	info = destination | (usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe)) << TD_TOKEN_TOGGLE);
-	tmp = swap_32(td_int[nint].link);
-	usb_fill_td(mytd,tmp,status, info,(unsigned long)buffer,(unsigned long)dev);
-	/* Link it */
-	tmp = swap_32((unsigned long)mytd);
-	td_int[nint].link=tmp;
-
-	usb_dotoggle (dev, usb_pipeendpoint (pipe), usb_pipeout (pipe));
-
-	return 0;
-}
-
-/**********************************************************************
- * Low Level functions
- */
-
-
-void reset_hc(void)
-{
-
-	/* Global reset for 100ms */
-	out16r( usb_base_addr + USBPORTSC1,0x0204);
-	out16r( usb_base_addr + USBPORTSC2,0x0204);
-	out16r( usb_base_addr + USBCMD,USBCMD_GRESET | USBCMD_RS);
-	/* Turn off all interrupts */
-	out16r(usb_base_addr + USBINTR,0);
-	wait_ms(50);
-	out16r( usb_base_addr + USBCMD,0);
-	wait_ms(10);
-}
-
-void start_hc(void)
-{
-	int timeout = 1000;
-
-	while(in16r(usb_base_addr + USBCMD) & USBCMD_HCRESET) {
-		if (!--timeout) {
-			printf("USBCMD_HCRESET timed out!\n");
-			break;
-		}
-	}
-	/* Turn on all interrupts */
-	out16r(usb_base_addr + USBINTR,USBINTR_TIMEOUT | USBINTR_RESUME | USBINTR_IOC | USBINTR_SP);
-	/* Start at frame 0 */
-	out16r(usb_base_addr + USBFRNUM,0);
-	/* set Framebuffer base address */
-	out32r(usb_base_addr+USBFLBASEADD,(unsigned long)&framelist);
-	/* Run and mark it configured with a 64-byte max packet */
-	out16r(usb_base_addr + USBCMD,USBCMD_RS | USBCMD_CF | USBCMD_MAXP);
-}
-
-/* Initialize the skeleton
- */
-void usb_init_skel(void)
-{
-	unsigned long temp;
-	int n;
-
-	for(n=0;n<USB_MAX_TEMP_INT_TD;n++)
-		tmp_int_td[n].dev_ptr=0L; /* no devices connected */
-	/* last td */
-	usb_fill_td(&td_last,UHCI_PTR_TERM,TD_CTRL_IOC ,0,0,0L);
-  /* usb_fill_td(&td_last,UHCI_PTR_TERM,0,0,0); */
-	/* End Queue Header */
-	usb_fill_qh(&qh_end,UHCI_PTR_TERM,(unsigned long)&td_last);
-	/* Bulk Queue Header */
-	temp=(unsigned long)&qh_end;
-	usb_fill_qh(&qh_bulk,temp | UHCI_PTR_QH,UHCI_PTR_TERM);
-	/* Control Queue Header */
-	temp=(unsigned long)&qh_bulk;
-	usb_fill_qh(&qh_cntrl, temp | UHCI_PTR_QH,UHCI_PTR_TERM);
-	/* 1ms Interrupt td */
-	temp=(unsigned long)&qh_cntrl;
-	usb_fill_td(&td_int[0],temp | UHCI_PTR_QH,0,0,0,0L);
-	temp=(unsigned long)&td_int[0];
-	for(n=1; n<8; n++)
-		usb_fill_td(&td_int[n],temp,0,0,0,0L);
-	for (n = 0; n < 1024; n++) {
-	/* link all framelist pointers to one of the interrupts */
-		int m, o;
-		if ((n&127)==127)
-			framelist[n]= swap_32((unsigned long)&td_int[0]);
-		else
-			for (o = 1, m = 2; m <= 128; o++, m += m)
-				if ((n & (m - 1)) == ((m - 1) / 2))
-						framelist[n]= swap_32((unsigned long)&td_int[o]);
-	}
-}
-
-/* check the common skeleton for completed transfers, and update the status
- * of the "connected" device. Called from the IRQ routine.
- */
-void usb_check_skel(void)
-{
-	struct usb_device *dev;
-	/* start with the control qh */
-	if(qh_cntrl.dev_ptr!=0) /* it's a device assigned check if this caused IRQ */
-	{
-		dev=(struct usb_device *)qh_cntrl.dev_ptr;
-		usb_get_td_status(&tmp_td[0],dev); /* update status */
-		if(!(dev->status & USB_ST_NOT_PROC)) { /* is not active anymore, disconnect devices */
-			qh_cntrl.dev_ptr=0;
-		}
-	}
-	/* now process the bulk */
-	if(qh_bulk.dev_ptr!=0) /* it's a device assigned check if this caused IRQ */
-	{
-		dev=(struct usb_device *)qh_bulk.dev_ptr;
-		usb_get_td_status(&tmp_td[0],dev); /* update status */
-		if(!(dev->status & USB_ST_NOT_PROC)) { /* is not active anymore, disconnect devices */
-			qh_bulk.dev_ptr=0;
-		}
-	}
-}
-
-/* check the interrupt chain, ubdate the status of the appropriate device,
- * call the appropriate irqhandler and reactivate the TD if the irqhandler
- * returns with 1
- */
-void usb_check_int_chain(void)
-{
-	int i,res;
-	unsigned long link,status;
-	struct usb_device *dev;
-	uhci_td_t *td,*prevtd;
-
-	for(i=0;i<8;i++) {
-		prevtd = &td_int[i]; /* the first previous td is the skeleton td */
-		link=swap_32(td_int[i].link) & 0xfffffff0; /* next in chain */
-		td=(uhci_td_t *)link; /* assign it */
-		/* all interrupt TDs are finally linked to the td_int[0].
-		 * so we process all until we find the td_int[0].
-		 * if int0 chain points to a QH, we're also done
-	   */
-		while(((i>0) && (link != (unsigned long)&td_int[0])) ||
-					((i==0) && !(swap_32(td->link) &  UHCI_PTR_QH)))
-		{
-			/* check if a device is assigned with this td */
-			status=swap_32(td->status);
-			if((td->dev_ptr!=0L) && !(status & TD_CTRL_ACTIVE)) {
-				/* td is not active and a device is assigned -> call irqhandler */
-				dev=(struct usb_device *)td->dev_ptr;
-				dev->irq_act_len=((status & 0x7FF)==0x7FF) ? 0 : (status & 0x7FF) + 1; /* transfered length */
-				dev->irq_status=usb_uhci_td_stat(status); /* get status */
-				res=dev->irq_handle(dev); /* call irqhandler */
-				if(res==1) {
-					/* reactivate */
-					status|=TD_CTRL_ACTIVE;
-					td->status=swap_32(status);
-					prevtd=td; /* previous td = this td */
-				}
-				else {
-					prevtd->link=td->link; /* link previous td directly to the nex td -> unlinked */
-					/* remove device pointer */
-					td->dev_ptr=0L;
-				}
-			} /* if we call the irq handler */
-			link=swap_32(td->link) & 0xfffffff0; /* next in chain */
-			td=(uhci_td_t *)link; /* assign it */
-		} /* process all td in this int chain */
-	} /* next interrupt chain */
-}
-
-
-/* usb interrupt service routine.
- */
-void handle_usb_interrupt(void)
-{
-	unsigned short status;
-
-	/*
-	 * Read the interrupt status, and write it back to clear the
-	 * interrupt cause
-	 */
-
-	status = in16r(usb_base_addr + USBSTS);
-
-	if (!status)		/* shared interrupt, not mine */
-		return;
-	if (status != 1) {
-		/* remove host controller halted state */
-		if ((status&0x20) && ((in16r(usb_base_addr+USBCMD) && USBCMD_RS)==0)) {
-			out16r(usb_base_addr + USBCMD, USBCMD_RS | in16r(usb_base_addr + USBCMD));
-		}
-	}
-	usb_check_int_chain(); /* call interrupt handlers for int tds */
-	usb_check_skel(); /* call completion handler for common transfer routines */
-	out16r(usb_base_addr+USBSTS,status);
-}
-
-
-/* init uhci
- */
-int usb_lowlevel_init(void)
-{
-	unsigned char temp;
-	int	busdevfunc;
-/*
- * HJF - configure IRQ and base from variables optionally.
- */
-	char *s;
-
-
-	busdevfunc=pci_find_device(USB_UHCI_VEND_ID,USB_UHCI_DEV_ID,0); /* get PCI Device ID */
-	if(busdevfunc == -1) {
-		printf("Error USB UHCI (%04X,%04X) not found\n",USB_UHCI_VEND_ID,USB_UHCI_DEV_ID);
-		return -1;
-	}
-
-#if 1
-	s = getenv("usb_irq");
-	if (s)
-	{
-	    temp = atoi(s);
-	    pci_write_config_byte(busdevfunc, PCI_INTERRUPT_LINE, temp);
-	}
-	else
-#endif
-	    pci_read_config_byte(busdevfunc,PCI_INTERRUPT_LINE,&temp);
-
-	s = getenv("usb_base");
-	if (s)
-	{
-	    unsigned long temp2;
-	    temp2 = atoi(s);
-	    pci_write_config_dword(busdevfunc, PCI_BASE_ADDRESS_4, temp2|0x01);
-	}
-
-	irqvec = temp;
-	irq_free_handler(irqvec);
-	USB_UHCI_PRINTF("Interrupt Line = %d\n",irqvec);
-	pci_read_config_byte(busdevfunc,PCI_INTERRUPT_PIN,&temp);
-	USB_UHCI_PRINTF("Interrupt Pin = %ld\n",temp);
-	pci_read_config_dword(busdevfunc,PCI_BASE_ADDRESS_4,&usb_base_addr);
-	USB_UHCI_PRINTF("IO Base Address = 0x%lx\n",usb_base_addr);
-	usb_base_addr&=0xFFFFFFF0;
-	usb_base_addr+=CONFIG_SYS_ISA_IO_BASE_ADDRESS;
-	rh.devnum = 0;
-	usb_init_skel();
-	reset_hc();
-	start_hc();
-	irq_install_handler(irqvec, (interrupt_handler_t *)handle_usb_interrupt, NULL);
-	irq_install_handler(0, (interrupt_handler_t *)handle_usb_interrupt, NULL);
-
-	return 0;
-}
-
-/* stop uhci
- */
-int usb_lowlevel_stop(void)
-{
-	if(irqvec == -1)
-		return 1;
-	irq_free_handler(irqvec);
-	irq_free_handler(0);
-	reset_hc();
-	irqvec = -1;
-	return 0;
-}
-
-/*******************************************************************************************
- * Virtual Root Hub
- * Since the uhci does not have a real HUB, we simulate one ;-)
- */
-#undef	USB_RH_DEBUG
-
-#ifdef	USB_RH_DEBUG
-#define	USB_RH_PRINTF(fmt,args...)	printf (fmt ,##args)
-static void usb_display_wValue(unsigned short wValue,unsigned short wIndex);
-static void usb_display_Req(unsigned short req);
-#else
-#define USB_RH_PRINTF(fmt,args...)
-static void usb_display_wValue(unsigned short wValue,unsigned short wIndex) {}
-static void usb_display_Req(unsigned short req) {}
-#endif
-
-static unsigned char root_hub_dev_des[] =
-{
-	0x12,			/*  __u8  bLength; */
-	0x01,			/*  __u8  bDescriptorType; Device */
-	0x00,			/*  __u16 bcdUSB; v1.0 */
-	0x01,
-	0x09,			/*  __u8  bDeviceClass; HUB_CLASSCODE */
-	0x00,			/*  __u8  bDeviceSubClass; */
-	0x00,			/*  __u8  bDeviceProtocol; */
-	0x08,			/*  __u8  bMaxPacketSize0; 8 Bytes */
-	0x00,			/*  __u16 idVendor; */
-	0x00,
-	0x00,			/*  __u16 idProduct; */
-	0x00,
-	0x00,			/*  __u16 bcdDevice; */
-	0x00,
-	0x01,			/*  __u8  iManufacturer; */
-	0x00,			/*  __u8  iProduct; */
-	0x00,			/*  __u8  iSerialNumber; */
-	0x01			/*  __u8  bNumConfigurations; */
-};
-
-
-/* Configuration descriptor */
-static unsigned char root_hub_config_des[] =
-{
-	0x09,			/*  __u8  bLength; */
-	0x02,			/*  __u8  bDescriptorType; Configuration */
-	0x19,			/*  __u16 wTotalLength; */
-	0x00,
-	0x01,			/*  __u8  bNumInterfaces; */
-	0x01,			/*  __u8  bConfigurationValue; */
-	0x00,			/*  __u8  iConfiguration; */
-	0x40,			/*  __u8  bmAttributes;
-				   Bit 7: Bus-powered, 6: Self-powered, 5 Remote-wakwup, 4..0: resvd */
-	0x00,			/*  __u8  MaxPower; */
-
-     /* interface */
-	0x09,			/*  __u8  if_bLength; */
-	0x04,			/*  __u8  if_bDescriptorType; Interface */
-	0x00,			/*  __u8  if_bInterfaceNumber; */
-	0x00,			/*  __u8  if_bAlternateSetting; */
-	0x01,			/*  __u8  if_bNumEndpoints; */
-	0x09,			/*  __u8  if_bInterfaceClass; HUB_CLASSCODE */
-	0x00,			/*  __u8  if_bInterfaceSubClass; */
-	0x00,			/*  __u8  if_bInterfaceProtocol; */
-	0x00,			/*  __u8  if_iInterface; */
-
-     /* endpoint */
-	0x07,			/*  __u8  ep_bLength; */
-	0x05,			/*  __u8  ep_bDescriptorType; Endpoint */
-	0x81,			/*  __u8  ep_bEndpointAddress; IN Endpoint 1 */
-	0x03,			/*  __u8  ep_bmAttributes; Interrupt */
-	0x08,			/*  __u16 ep_wMaxPacketSize; 8 Bytes */
-	0x00,
-	0xff			/*  __u8  ep_bInterval; 255 ms */
-};
-
-
-static unsigned char root_hub_hub_des[] =
-{
-	0x09,			/*  __u8  bLength; */
-	0x29,			/*  __u8  bDescriptorType; Hub-descriptor */
-	0x02,			/*  __u8  bNbrPorts; */
-	0x00,			/* __u16  wHubCharacteristics; */
-	0x00,
-	0x01,			/*  __u8  bPwrOn2pwrGood; 2ms */
-	0x00,			/*  __u8  bHubContrCurrent; 0 mA */
-	0x00,			/*  __u8  DeviceRemovable; *** 7 Ports max *** */
-	0xff			/*  __u8  PortPwrCtrlMask; *** 7 ports max *** */
-};
-
-static unsigned char root_hub_str_index0[] =
-{
-	0x04,			/*  __u8  bLength; */
-	0x03,			/*  __u8  bDescriptorType; String-descriptor */
-	0x09,			/*  __u8  lang ID */
-	0x04,			/*  __u8  lang ID */
-};
-
-static unsigned char root_hub_str_index1[] =
-{
-	28,			/*  __u8  bLength; */
-	0x03,			/*  __u8  bDescriptorType; String-descriptor */
-	'U',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'H',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'C',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'I',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	' ',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'R',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'o',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'o',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	't',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	' ',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'H',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'u',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-	'b',			/*  __u8  Unicode */
-	0,				/*  __u8  Unicode */
-};
-
-
-/*
- * Root Hub Control Pipe (interrupt Pipes are not supported)
- */
-
-
-int uhci_submit_rh_msg(struct usb_device *dev, unsigned long pipe, void *buffer,int transfer_len,struct devrequest *cmd)
-{
-	void *data = buffer;
-	int leni = transfer_len;
-	int len = 0;
-	int status = 0;
-	int stat = 0;
-	int i;
-
-	unsigned short cstatus;
-
-	unsigned short bmRType_bReq;
-	unsigned short wValue;
-	unsigned short wIndex;
-	unsigned short wLength;
-
-	if (usb_pipeint(pipe)) {
-		printf("Root-Hub submit IRQ: NOT implemented\n");
-#if 0
-		uhci->rh.urb = urb;
-		uhci->rh.send = 1;
-		uhci->rh.interval = urb->interval;
-		rh_init_int_timer (urb);
-#endif
-		return 0;
-	}
-	bmRType_bReq = cmd->requesttype | cmd->request << 8;
-	wValue = swap_16(cmd->value);
-	wIndex = swap_16(cmd->index);
-	wLength = swap_16(cmd->length);
-	usb_display_Req(bmRType_bReq);
-	for (i = 0; i < 8; i++)
-		rh.c_p_r[i] = 0;
-	USB_RH_PRINTF("Root-Hub: adr: %2x cmd(%1x): %02x%02x %04x %04x %04x\n",
-	     dev->devnum, 8, cmd->requesttype,cmd->request, wValue, wIndex, wLength);
-
-	switch (bmRType_bReq) {
-		/* Request Destination:
-		   without flags: Device,
-		   RH_INTERFACE: interface,
-		   RH_ENDPOINT: endpoint,
-		   RH_CLASS means HUB here,
-		   RH_OTHER | RH_CLASS  almost ever means HUB_PORT here
-		 */
-
-	case RH_GET_STATUS:
-		*(unsigned short *) data = swap_16(1);
-		len=2;
-		break;
-	case RH_GET_STATUS | RH_INTERFACE:
-		*(unsigned short *) data = swap_16(0);
-		len=2;
-		break;
-	case RH_GET_STATUS | RH_ENDPOINT:
-		*(unsigned short *) data = swap_16(0);
-		len=2;
-		break;
-	case RH_GET_STATUS | RH_CLASS:
-		*(unsigned long *) data = swap_32(0);
-		len=4;
-		break;	/* hub power ** */
-	case RH_GET_STATUS | RH_OTHER | RH_CLASS:
-
-		status = in16r(usb_base_addr + USBPORTSC1 + 2 * (wIndex - 1));
-		cstatus = ((status & USBPORTSC_CSC) >> (1 - 0)) |
-			((status & USBPORTSC_PEC) >> (3 - 1)) |
-			(rh.c_p_r[wIndex - 1] << (0 + 4));
-		status = (status & USBPORTSC_CCS) |
-			((status & USBPORTSC_PE) >> (2 - 1)) |
-			((status & USBPORTSC_SUSP) >> (12 - 2)) |
-			((status & USBPORTSC_PR) >> (9 - 4)) |
-			(1 << 8) |	/* power on ** */
-			((status & USBPORTSC_LSDA) << (-8 + 9));
-
-		*(unsigned short *) data = swap_16(status);
-		*(unsigned short *) (data + 2) = swap_16(cstatus);
-		len=4;
-		break;
-	case RH_CLEAR_FEATURE | RH_ENDPOINT:
-		switch (wValue) {
-		case (RH_ENDPOINT_STALL):
-			len=0;
-			break;
-		}
-		break;
-
-	case RH_CLEAR_FEATURE | RH_CLASS:
-		switch (wValue) {
-		case (RH_C_HUB_OVER_CURRENT):
-			len=0;	/* hub power over current ** */
-			break;
-		}
-		break;
-
-	case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS:
-		usb_display_wValue(wValue,wIndex);
-		switch (wValue) {
-		case (RH_PORT_ENABLE):
-			status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1));
-			status = (status & 0xfff5) & ~USBPORTSC_PE;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			len=0;
-			break;
-		case (RH_PORT_SUSPEND):
-			status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1));
-			status = (status & 0xfff5) & ~USBPORTSC_SUSP;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			len=0;
-			break;
-		case (RH_PORT_POWER):
-			len=0;	/* port power ** */
-			break;
-		case (RH_C_PORT_CONNECTION):
-			status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1));
-			status = (status & 0xfff5) | USBPORTSC_CSC;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			len=0;
-			break;
-		case (RH_C_PORT_ENABLE):
-			status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1));
-			status = (status & 0xfff5) | USBPORTSC_PEC;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			len=0;
-			break;
-		case (RH_C_PORT_SUSPEND):
-/*** WR_RH_PORTSTAT(RH_PS_PSSC); */
-			len=0;
-			break;
-		case (RH_C_PORT_OVER_CURRENT):
-			len=0;
-			break;
-		case (RH_C_PORT_RESET):
-			rh.c_p_r[wIndex - 1] = 0;
-			len=0;
-			break;
-		}
-		break;
-	case RH_SET_FEATURE | RH_OTHER | RH_CLASS:
-		usb_display_wValue(wValue,wIndex);
-		switch (wValue) {
-		case (RH_PORT_SUSPEND):
-			status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1));
-			status = (status & 0xfff5) | USBPORTSC_SUSP;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			len=0;
-			break;
-		case (RH_PORT_RESET):
-			status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1));
-			status = (status & 0xfff5) | USBPORTSC_PR;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			wait_ms(10);
-			status = (status & 0xfff5) & ~USBPORTSC_PR;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			udelay(10);
-			status = (status & 0xfff5) | USBPORTSC_PE;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			wait_ms(10);
-			status = (status & 0xfff5) | 0xa;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			len=0;
-			break;
-		case (RH_PORT_POWER):
-			len=0;	/* port power ** */
-			break;
-		case (RH_PORT_ENABLE):
-			status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1));
-			status = (status & 0xfff5) | USBPORTSC_PE;
-			out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status);
-			len=0;
-			break;
-		}
-		break;
-
-	case RH_SET_ADDRESS:
-		rh.devnum = wValue;
-		len=0;
-		break;
-	case RH_GET_DESCRIPTOR:
-		switch ((wValue & 0xff00) >> 8) {
-		case (0x01):	/* device descriptor */
-			i=sizeof(root_hub_config_des);
-			status=i > wLength ? wLength : i;
-			len = leni > status ? status : leni;
-			memcpy (data, root_hub_dev_des, len);
-			break;
-		case (0x02):	/* configuration descriptor */
-			i=sizeof(root_hub_config_des);
-			status=i > wLength ? wLength : i;
-			len = leni > status ? status : leni;
-			memcpy (data, root_hub_config_des, len);
-			break;
-		case (0x03):	/*string descriptors */
-			if(wValue==0x0300) {
-				i=sizeof(root_hub_str_index0);
-				status = i > wLength ? wLength : i;
-				len = leni > status ? status : leni;
-				memcpy (data, root_hub_str_index0, len);
-				break;
-			}
-			if(wValue==0x0301) {
-				i=sizeof(root_hub_str_index1);
-				status = i > wLength ? wLength : i;
-				len = leni > status ? status : leni;
-				memcpy (data, root_hub_str_index1, len);
-				break;
-			}
-			stat = USB_ST_STALLED;
-		}
-		break;
-
-	case RH_GET_DESCRIPTOR | RH_CLASS:
-		root_hub_hub_des[2] = 2;
-		i=sizeof(root_hub_hub_des);
-		status= i > wLength ? wLength : i;
-		len = leni > status ? status : leni;
-		memcpy (data, root_hub_hub_des, len);
-		break;
-	case RH_GET_CONFIGURATION:
-		*(unsigned char *) data = 0x01;
-		len = 1;
-		break;
-	case RH_SET_CONFIGURATION:
-		len=0;
-		break;
-	default:
-		stat = USB_ST_STALLED;
-	}
-	USB_RH_PRINTF("Root-Hub stat %lx port1: %x port2: %x\n\n",stat,
-	     in16r(usb_base_addr + USBPORTSC1), in16r(usb_base_addr + USBPORTSC2));
-	dev->act_len=len;
-	dev->status=stat;
-	return stat;
-
-}
-
-/********************************************************************************
- * Some Debug Routines
- */
-
-#ifdef	USB_RH_DEBUG
-
-static void usb_display_Req(unsigned short req)
-{
-	USB_RH_PRINTF("- Root-Hub Request: ");
-	switch (req) {
-	case RH_GET_STATUS:
-		USB_RH_PRINTF("Get Status ");
-		break;
-	case RH_GET_STATUS | RH_INTERFACE:
-		USB_RH_PRINTF("Get Status Interface ");
-		break;
-	case RH_GET_STATUS | RH_ENDPOINT:
-		USB_RH_PRINTF("Get Status Endpoint ");
-		break;
-	case RH_GET_STATUS | RH_CLASS:
-		USB_RH_PRINTF("Get Status Class");
-		break;	/* hub power ** */
-	case RH_GET_STATUS | RH_OTHER | RH_CLASS:
-		USB_RH_PRINTF("Get Status Class Others");
-		break;
-	case RH_CLEAR_FEATURE | RH_ENDPOINT:
-		USB_RH_PRINTF("Clear Feature Endpoint ");
-		break;
-	case RH_CLEAR_FEATURE | RH_CLASS:
-		USB_RH_PRINTF("Clear Feature Class ");
-		break;
-	case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS:
-		USB_RH_PRINTF("Clear Feature Other Class ");
-		break;
-	case RH_SET_FEATURE | RH_OTHER | RH_CLASS:
-		USB_RH_PRINTF("Set Feature Other Class ");
-		break;
-	case RH_SET_ADDRESS:
-		USB_RH_PRINTF("Set Address ");
-		break;
-	case RH_GET_DESCRIPTOR:
-		USB_RH_PRINTF("Get Descriptor ");
-		break;
-	case RH_GET_DESCRIPTOR | RH_CLASS:
-		USB_RH_PRINTF("Get Descriptor Class ");
-		break;
-	case RH_GET_CONFIGURATION:
-		USB_RH_PRINTF("Get Configuration ");
-		break;
-	case RH_SET_CONFIGURATION:
-		USB_RH_PRINTF("Get Configuration ");
-		break;
-	default:
-		USB_RH_PRINTF("****UNKNOWN**** 0x%04X ",req);
-	}
-	USB_RH_PRINTF("\n");
-
-}
-
-static void usb_display_wValue(unsigned short wValue,unsigned short wIndex)
-{
-	switch (wValue) {
-		case (RH_PORT_ENABLE):
-			USB_RH_PRINTF("Root-Hub: Enable Port %d\n",wIndex);
-			break;
-		case (RH_PORT_SUSPEND):
-			USB_RH_PRINTF("Root-Hub: Suspend Port %d\n",wIndex);
-			break;
-		case (RH_PORT_POWER):
-			USB_RH_PRINTF("Root-Hub: Port Power %d\n",wIndex);
-			break;
-		case (RH_C_PORT_CONNECTION):
-			USB_RH_PRINTF("Root-Hub: C Port Connection Port %d\n",wIndex);
-			break;
-		case (RH_C_PORT_ENABLE):
-			USB_RH_PRINTF("Root-Hub: C Port Enable Port %d\n",wIndex);
-			break;
-		case (RH_C_PORT_SUSPEND):
-			USB_RH_PRINTF("Root-Hub: C Port Suspend Port %d\n",wIndex);
-			break;
-		case (RH_C_PORT_OVER_CURRENT):
-			USB_RH_PRINTF("Root-Hub: C Port Over Current Port %d\n",wIndex);
-			break;
-		case (RH_C_PORT_RESET):
-			USB_RH_PRINTF("Root-Hub: C Port reset Port %d\n",wIndex);
-			break;
-		default:
-			USB_RH_PRINTF("Root-Hub: unknown %x %x\n",wValue,wIndex);
-			break;
-	}
-}
-
-#endif
-
-
-#ifdef	USB_UHCI_DEBUG
-
-static int usb_display_td(uhci_td_t *td)
-{
-	unsigned long tmp;
-	int valid;
-
-	printf("TD at %p:\n",td);
-
-	tmp=swap_32(td->link);
-	printf("Link points to 0x%08lX, %s first, %s, %s\n",tmp&0xfffffff0,
-		((tmp & 0x4)==0x4) ? "Depth" : "Breath",
-		((tmp & 0x2)==0x2) ? "QH" : "TD",
-		((tmp & 0x1)==0x1) ? "invalid" : "valid");
-	valid=((tmp & 0x1)==0x0);
-	tmp=swap_32(td->status);
-	printf("     %s %ld Errors %s %s %s \n     %s %s %s %s %s %s\n     Len 0x%lX\n",
-		(((tmp>>29)&0x1)==0x1) ? "SPD Enable" : "SPD Disable",
-		((tmp>>28)&0x3),
-		(((tmp>>26)&0x1)==0x1) ? "Low Speed" : "Full Speed",
-		(((tmp>>25)&0x1)==0x1) ? "ISO " : "",
-		(((tmp>>24)&0x1)==0x1) ? "IOC " : "",
-		(((tmp>>23)&0x1)==0x1) ? "Active " : "Inactive ",
-		(((tmp>>22)&0x1)==0x1) ? "Stalled" : "",
-		(((tmp>>21)&0x1)==0x1) ? "Data Buffer Error" : "",
-		(((tmp>>20)&0x1)==0x1) ? "Babble" : "",
-		(((tmp>>19)&0x1)==0x1) ? "NAK" : "",
-		(((tmp>>18)&0x1)==0x1) ? "Bitstuff Error" : "",
-		(tmp&0x7ff));
-	tmp=swap_32(td->info);
-	printf("     MaxLen 0x%lX\n",((tmp>>21)&0x7FF));
-	printf("     %s Endpoint 0x%lX Dev Addr 0x%lX PID 0x%lX\n",((tmp>>19)&0x1)==0x1 ? "TOGGLE" : "",
-		((tmp>>15)&0xF),((tmp>>8)&0x7F),tmp&0xFF);
-	tmp=swap_32(td->buffer);
-	printf("     Buffer 0x%08lX\n",tmp);
-	printf("     DEV %08lX\n",td->dev_ptr);
-	return valid;
-}
-
-
-void usb_show_td(int max)
-{
-	int i;
-	if(max>0) {
-		for(i=0;i<max;i++) {
-			usb_display_td(&tmp_td[i]);
-		}
-	}
-	else {
-		i=0;
-		do {
-			printf("tmp_td[%d]\n",i);
-		}while(usb_display_td(&tmp_td[i++]));
-	}
-}
-
-
-#endif
-#endif /* CONFIG_USB_UHCI */
-
-/* EOF */
diff --git a/board/MAI/AmigaOneG3SE/usb_uhci.h b/board/MAI/AmigaOneG3SE/usb_uhci.h
deleted file mode 100644
index 3387157..0000000
--- a/board/MAI/AmigaOneG3SE/usb_uhci.h
+++ /dev/null
@@ -1,192 +0,0 @@
-/*
- * (C) Copyright 2001
- * Denis Peter, MPL AG Switzerland
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Note: Part of this code has been derived from linux
- *
- */
-#ifndef _USB_UHCI_H_
-#define _USB_UHCI_H_
-
-#undef USB_UHCI_VEND_ID
-#define USB_UHCI_VEND_ID PCI_VENDOR_ID_VIA
-#undef USB_UHCI_DEV_ID
-#define USB_UHCI_DEV_ID 0x3038
-
-/* Command register */
-#define USBCMD		0
-#define   USBCMD_RS       0x0001	/* Run/Stop */
-#define   USBCMD_HCRESET  0x0002	/* Host reset */
-#define   USBCMD_GRESET   0x0004	/* Global reset */
-#define   USBCMD_EGSM     0x0008	/* Global Suspend Mode */
-#define   USBCMD_FGR      0x0010	/* Force Global Resume */
-#define   USBCMD_SWDBG    0x0020	/* SW Debug mode */
-#define   USBCMD_CF       0x0040	/* Config Flag (sw only) */
-#define   USBCMD_MAXP     0x0080	/* Max Packet (0 = 32, 1 = 64) */
-
-/* Status register */
-#define USBSTS		2
-#define   USBSTS_USBINT   0x0001	/* Interrupt due to IOC */
-#define   USBSTS_ERROR    0x0002	/* Interrupt due to error */
-#define   USBSTS_RD       0x0004	/* Resume Detect */
-#define   USBSTS_HSE      0x0008	/* Host System Error - basically PCI problems */
-#define   USBSTS_HCPE     0x0010	/* Host Controller Process Error - the scripts were buggy */
-#define   USBSTS_HCH      0x0020	/* HC Halted */
-
-/* Interrupt enable register */
-#define USBINTR		4
-#define   USBINTR_TIMEOUT 0x0001	/* Timeout/CRC error enable */
-#define   USBINTR_RESUME  0x0002	/* Resume interrupt enable */
-#define   USBINTR_IOC     0x0004	/* Interrupt On Complete enable */
-#define   USBINTR_SP      0x0008	/* Short packet interrupt enable */
-
-#define USBFRNUM      6
-#define USBFLBASEADD  8
-#define USBSOF        12
-
-/* USB port status and control registers */
-#define USBPORTSC1	16
-#define USBPORTSC2	18
-#define   USBPORTSC_CCS   0x0001	/* Current Connect Status ("device present") */
-#define   USBPORTSC_CSC   0x0002	/* Connect Status Change */
-#define   USBPORTSC_PE    0x0004	/* Port Enable */
-#define   USBPORTSC_PEC   0x0008	/* Port Enable Change */
-#define   USBPORTSC_LS    0x0030	/* Line Status */
-#define   USBPORTSC_RD    0x0040	/* Resume Detect */
-#define   USBPORTSC_LSDA  0x0100	/* Low Speed Device Attached */
-#define   USBPORTSC_PR    0x0200	/* Port Reset */
-#define   USBPORTSC_SUSP  0x1000	/* Suspend */
-
-/* Legacy support register */
-#define USBLEGSUP 0xc0
-#define USBLEGSUP_DEFAULT 0x2000	/* only PIRQ enable set */
-
-#define UHCI_NULL_DATA_SIZE 0x7ff	/* for UHCI controller TD */
-#define UHCI_PID            0xff	/* PID MASK */
-
-#define UHCI_PTR_BITS       0x000F
-#define UHCI_PTR_TERM       0x0001
-#define UHCI_PTR_QH         0x0002
-#define UHCI_PTR_DEPTH      0x0004
-
-/* for TD <status>: */
-#define TD_CTRL_SPD         (1 << 29)	/* Short Packet Detect */
-#define TD_CTRL_C_ERR_MASK  (3 << 27)	/* Error Counter bits */
-#define TD_CTRL_LS          (1 << 26)	/* Low Speed Device */
-#define TD_CTRL_IOS         (1 << 25)	/* Isochronous Select */
-#define TD_CTRL_IOC         (1 << 24)	/* Interrupt on Complete */
-#define TD_CTRL_ACTIVE      (1 << 23)	/* TD Active */
-#define TD_CTRL_STALLED     (1 << 22)	/* TD Stalled */
-#define TD_CTRL_DBUFERR     (1 << 21)	/* Data Buffer Error */
-#define TD_CTRL_BABBLE      (1 << 20)	/* Babble Detected */
-#define TD_CTRL_NAK         (1 << 19)	/* NAK Received */
-#define TD_CTRL_CRCTIMEO    (1 << 18)	/* CRC/Time Out Error */
-#define TD_CTRL_BITSTUFF    (1 << 17)	/* Bit Stuff Error */
-#define TD_CTRL_ACTLEN_MASK 0x7ff	/* actual length, encoded as n - 1 */
-
-#define TD_CTRL_ANY_ERROR	(TD_CTRL_STALLED | TD_CTRL_DBUFERR | \
-				 TD_CTRL_BABBLE | TD_CTRL_CRCTIME | TD_CTRL_BITSTUFF)
-
-#define TD_TOKEN_TOGGLE		19
-
-/* ------------------------------------------------------------------------------------
-   Virtual Root HUB
-   ------------------------------------------------------------------------------------ */
-/* destination of request */
-#define RH_INTERFACE               0x01
-#define RH_ENDPOINT                0x02
-#define RH_OTHER                   0x03
-
-#define RH_CLASS                   0x20
-#define RH_VENDOR                  0x40
-
-/* Requests: bRequest << 8 | bmRequestType */
-#define RH_GET_STATUS           0x0080
-#define RH_CLEAR_FEATURE        0x0100
-#define RH_SET_FEATURE          0x0300
-#define RH_SET_ADDRESS          0x0500
-#define RH_GET_DESCRIPTOR       0x0680
-#define RH_SET_DESCRIPTOR       0x0700
-#define RH_GET_CONFIGURATION    0x0880
-#define RH_SET_CONFIGURATION    0x0900
-#define RH_GET_STATE            0x0280
-#define RH_GET_INTERFACE        0x0A80
-#define RH_SET_INTERFACE        0x0B00
-#define RH_SYNC_FRAME           0x0C80
-/* Our Vendor Specific Request */
-#define RH_SET_EP               0x2000
-
-/* Hub port features */
-#define RH_PORT_CONNECTION         0x00
-#define RH_PORT_ENABLE             0x01
-#define RH_PORT_SUSPEND            0x02
-#define RH_PORT_OVER_CURRENT       0x03
-#define RH_PORT_RESET              0x04
-#define RH_PORT_POWER              0x08
-#define RH_PORT_LOW_SPEED          0x09
-#define RH_C_PORT_CONNECTION       0x10
-#define RH_C_PORT_ENABLE           0x11
-#define RH_C_PORT_SUSPEND          0x12
-#define RH_C_PORT_OVER_CURRENT     0x13
-#define RH_C_PORT_RESET            0x14
-
-/* Hub features */
-#define RH_C_HUB_LOCAL_POWER       0x00
-#define RH_C_HUB_OVER_CURRENT      0x01
-
-#define RH_DEVICE_REMOTE_WAKEUP    0x00
-#define RH_ENDPOINT_STALL          0x01
-
-/* Our Vendor Specific feature */
-#define RH_REMOVE_EP               0x00
-
-
-#define RH_ACK                     0x01
-#define RH_REQ_ERR                 -1
-#define RH_NACK                    0x00
-
-
-/* Transfer descriptor structure */
-typedef struct {
-	unsigned long link;     /* next td/qh (LE)*/
-	unsigned long status;   /* status of the td */
-	unsigned long info;     /* Max Lenght / Endpoint / device address and PID */
-	unsigned long buffer;   /* pointer to data buffer (LE) */
-	unsigned long dev_ptr;  /* pointer to the assigned device (BE) */
-	unsigned long res[3];   /* reserved (TDs must be 8Byte aligned) */
-} uhci_td_t, *puhci_td_t;
-
-/* Queue Header structure */
-typedef struct {
-	unsigned long head;       /* Next QH (LE)*/
-	unsigned long element;		/* Queue element pointer (LE) */
-	unsigned long res[5];     /* reserved */
-	unsigned long dev_ptr;    /* if 0 no tds have been assigned to this qh */
-} uhci_qh_t, *puhci_qh_t;
-
-struct virt_root_hub {
-	int devnum;		            /* Address of Root Hub endpoint */
-	int numports;             /* number of ports */
-	int c_p_r[8];             /* C_PORT_RESET */
-};
-
-
-#endif /* _USB_UHCI_H_ */
diff --git a/board/MAI/AmigaOneG3SE/via686.c b/board/MAI/AmigaOneG3SE/via686.c
deleted file mode 100644
index 752a464..0000000
--- a/board/MAI/AmigaOneG3SE/via686.c
+++ /dev/null
@@ -1,299 +0,0 @@
-/*
- * (C) Copyright 2002
- * Hyperion Entertainment, Hans-JoergF@hyperion-entertainment.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-#include <pci.h>
-#include <ata.h>
-#include "memio.h"
-#include "articiaS.h"
-#include "via686.h"
-#include "i8259.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#undef VIA_DEBUG
-
-#ifdef  VIA_DEBUG
-#define PRINTF(fmt,args...)     printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-
-/*  Setup the ISA-to-PCI host bridge */
-void via_isa_init(pci_dev_t dev, struct pci_config_table *table)
-{
-    char regval;
-    if (PCI_FUNC(dev) == 0)
-    {
-	PRINTF("... PCI-to-ISA bridge, dev=0x%X\n", dev);
-
-	/*  Enable I/O Recovery time */
-	pci_write_config_byte(dev, 0x40, 0x08);
-
-	/*  Enable ISA refresh */
-	pci_write_config_byte(dev, 0x41, 0x41); /*  was 01 */
-
-	/*  Enable ISA line buffer */
-	pci_write_config_byte(dev, 0x45, 0x80);
-
-	/*  Gate INTR, and flush line buffer */
-	pci_write_config_byte(dev, 0x46, 0x60);
-
-	/*  Enable EISA ports 4D0/4D1. Do we need this ? */
-	pci_write_config_byte(dev, 0x47, 0xe6); /*  was 20 */
-
-	/*  512 K PCI Decode */
-	pci_write_config_byte(dev, 0x48, 0x01);
-
-	/*  Wait for PGNT before grant to ISA Master/DMA */
-	/*  ports 0-FF to SDBus */
-	/*  IRQ 14 and 15 for ide 0/1 */
-	pci_write_config_byte(dev, 0x4a, 0x04); /*  Was c4 */
-
-	/*  Plug'n'Play */
-	/*  Parallel DRQ 3, Floppy DRQ 2 (default) */
-	pci_write_config_byte(dev, 0x50, 0x0e);
-
-	/*  IRQ Routing for Floppy and Parallel port */
-	/*  IRQ 6 for floppy, IRQ 7 for parallel port */
-	pci_write_config_byte(dev, 0x51, 0x76);
-
-	/*  IRQ Routing for serial ports (take IRQ 3 and 4) */
-	pci_write_config_byte(dev, 0x52, 0x34);
-
-	/*  All IRQ's level triggered. */
-	pci_write_config_byte(dev, 0x54, 0x00);
-
-	/*  PCI IRQ's all at IRQ 9 */
-	pci_write_config_byte(dev, 0x55, 0x90);
-	pci_write_config_byte(dev, 0x56, 0x99);
-	pci_write_config_byte(dev, 0x57, 0x90);
-
-	/*  Enable Keyboard */
-	pci_read_config_byte(dev, 0x5A, &regval);
-	regval |= 0x01;
-	pci_write_config_byte(dev, 0x5A, regval);
-
-	pci_write_config_byte(dev, 0x80, 0);
-	pci_write_config_byte(dev, 0x85, 0x01);
-
-/*	pci_write_config_byte(dev, 0x77, 0x00); */
-    }
-}
-
-/*
- * Initialize PNP irq routing
- */
-
-void via_init_irq_routing(uint8 irq_map[])
-{
-    char *s;
-    uint8 level_edge_bits = 0xf;
-
-    /* Set irq routings */
-    pci_write_cfg_byte(0, 7<<3, 0x55, irq_map[0]<<4);
-    pci_write_cfg_byte(0, 7<<3, 0x56, irq_map[1] | irq_map[2]<<4);
-    pci_write_cfg_byte(0, 7<<3, 0x57, irq_map[3]<<4);
-
-    /*
-     * Gather level/edge bits
-     * Default is to assume level triggered
-     */
-
-    s = getenv("pci_irqa_select");
-    if (s && strcmp(s, "level") == 0)
-	level_edge_bits &= ~0x01;
-
-    s = getenv("pci_irqb_select");
-    if (s && strcmp(s, "level") == 0)
-	level_edge_bits &= ~0x02;
-
-    s = getenv("pci_irqc_select");
-    if (s && strcmp(s, "level") == 0)
-	level_edge_bits &= ~0x04;
-
-    s = getenv("pci_irqd_select");
-    if (s && strcmp(s, "level") == 0)
-	level_edge_bits &= ~0x08;
-
-    PRINTF("IRQ map\n");
-    PRINTF("%d: %s\n", irq_map[0], level_edge_bits&0x1 ? "edge" : "level");
-    PRINTF("%d: %s\n", irq_map[1], level_edge_bits&0x2 ? "edge" : "level");
-    PRINTF("%d: %s\n", irq_map[2], level_edge_bits&0x4 ? "edge" : "level");
-    PRINTF("%d: %s\n", irq_map[3], level_edge_bits&0x8 ? "edge" : "level");
-    pci_write_cfg_byte(0, 7<<3, 0x54, level_edge_bits);
-
-    PRINTF("%02x %02x %02x %02x\n", pci_read_cfg_byte(0, 7<<3, 0x54),
-	   pci_read_cfg_byte(0, 7<<3, 0x55), pci_read_cfg_byte(0, 7<<3, 0x56),
-	   pci_read_cfg_byte(0, 7<<3, 0x57));
-}
-
-
-/*  Setup the IDE controller. This doesn't seem to work yet. I/O to an IDE controller port */
-/*  always return the last character output on the serial port (!) */
-/*  This function is called by the pnp-library when it encounters 0:7:1 */
-void via_cfgfunc_ide_init(struct pci_controller *host, pci_dev_t dev, struct pci_config_table *table)
-{
-    PRINTF("... IDE controller, dev=0x%X\n", dev);
-
-    /*  Enable both IDE channels. */
-    pci_write_config_byte(dev, 0x40, 0x03);
-    /*  udelay(10000); */
-    /*  udelay(10000); */
-
-    /*  Enable IO Space */
-    pci_write_config_word(dev, 0x04, 0x03);
-
-    /*  Set to compatibility mode */
-    pci_write_config_byte(dev, 0x09, 0x8A); /*  WAS: 0x8f); */
-
-    /*  Set to legacy interrupt mode */
-    pci_write_config_byte(dev, 0x3d, 0x00); /* WAS: 0x01); */
-
-}
-
-
-/*  Set the base address of the floppy controller to 0x3F0 */
-void via_fdc_init(pci_dev_t dev)
-{
-    unsigned char c;
-    /*  Enable Configuration mode */
-    pci_read_config_byte(dev, 0x85, &c);
-    c |= 0x02;
-    pci_write_config_byte(dev, 0x85, c);
-
-    /*  Set floppy controller port to 0x3F0. */
-    SIO_WRITE_CONFIG(0xE3, (0x3F<<2));
-
-    /*  Enable floppy controller */
-    SIO_READ_CONFIG(0xE2, c);
-    c |= 0x10;
-    SIO_WRITE_CONFIG(0xE2, c);
-
-    /*  Switch of configuration mode */
-    pci_read_config_byte(dev, 0x85, &c);
-    c &= ~0x02;
-    pci_write_config_byte(dev, 0x85, c);
-}
-
-/*  Init function 0 of the via southbridge. Called by the pnp-library */
-void via_cfgfunc_via686(struct pci_controller *host, pci_dev_t dev, struct pci_config_table *table)
-{
-    if (PCI_FUNC(dev) == 0)
-    {
-	/* FIXME: Try to generate a PCI reset */
-	/* unsigned char c; */
-	/* pci_read_config_byte(dev, 0x47, &c); */
-	/* pci_write_config_byte(dev, 0x47, c | 0x01); */
-
-	via_isa_init(dev, table);
-	via_fdc_init(dev);
-    }
-}
-
-__asm__       ("    .globl via_calibrate_time_base \n"
-	       "via_calibrate_time_base:	   \n"
-	       "   lis     9, 0xfe00		   \n"
-	       "   li      0, 0x00		   \n"
-	       "   mttbu   0			   \n"
-	       "   mttbl   0			   \n"
-	       "ctb_loop:			   \n"
-	       "   lbz     0, 0x61(9)		   \n"
-	       "   eieio			   \n"
-	       "   andi.   0, 0, 0x20		   \n"
-	       "   beq     ctb_loop		   \n"
-	       "ctb_done:			   \n"
-	       "   mftb    3			   \n"
-	       "   blr");
-
-extern unsigned long via_calibrate_time_base(void);
-
-void via_calibrate_bus_freq (void)
-{
-	unsigned long tb;
-
-	/* This is 20 microseconds */
-#define CALIBRATE_TIME 28636
-
-	/* Enable the timer (and disable speaker) */
-	unsigned char c;
-
-	c = in_byte (0x61);
-	out_byte (0x61, ((c & ~0x02) | 0x01));
-
-	/* Set timer 2 to low/high writing */
-	out_byte (0x43, 0xb0);
-	out_byte (0x42, CALIBRATE_TIME & 0xff);
-	out_byte (0x42, CALIBRATE_TIME >> 8);
-
-	/* Read the time base */
-	tb = via_calibrate_time_base ();
-
-	if (tb >= 700000)
-		gd->bus_clk = 133333333;
-	else
-		gd->bus_clk = 100000000;
-
-}
-
-
-void ide_led(uchar led, uchar status)
-{
-/*     unsigned char c = in_byte(0x92); */
-
-/*     if (!status) */
-/*	out_byte(0x92, c | 0xC0); */
-/*     else */
-/*	out_byte(0x92, c & ~0xC0); */
-}
-
-
-void via_init_afterscan(void)
-{
-    /* Modify IDE controller setup */
-    pci_write_cfg_byte(0, 7<<3|1, PCI_LATENCY_TIMER, 0x20);
-    pci_write_cfg_byte(0, 7<<3|1, PCI_COMMAND, PCI_COMMAND_IO|PCI_COMMAND_MEMORY|PCI_COMMAND_MASTER);
-    pci_write_cfg_byte(0, 7<<3|1, PCI_INTERRUPT_LINE, 0xff);
-    pci_write_cfg_byte(0, 7<<3|1, 0x40, 0x0b);   /* FIXME: Might depend on drives connected */
-    pci_write_cfg_byte(0, 7<<3|1, 0x41, 0x42);   /* FIXME: Might depend on drives connected */
-    pci_write_cfg_byte(0, 7<<3|1, 0x43, 0x05);
-    pci_write_cfg_byte(0, 7<<3|1, 0x44, 0x18);
-    pci_write_cfg_byte(0, 7<<3|1, 0x45, 0x10);
-    pci_write_cfg_byte(0, 7<<3|1, 0x4e, 0x22);   /* FIXME: Not documented, but set in PC bios */
-    pci_write_cfg_byte(0, 7<<3|1, 0x4f, 0x20);   /* FIXME: Not documented */
-
-    /* Modify some values in the USB controller */
-    pci_write_cfg_byte(0, 7<<3|2, 0x05, 0x17);
-    pci_write_cfg_byte(0, 7<<3|2, 0x06, 0x01);
-    pci_write_cfg_byte(0, 7<<3|2, 0x41, 0x12);
-    pci_write_cfg_byte(0, 7<<3|2, 0x42, 0x03);
-    pci_write_cfg_byte(0, 7<<3|2, PCI_LATENCY_TIMER, 0x40);
-
-    pci_write_cfg_byte(0, 7<<3|3, 0x05, 0x17);
-    pci_write_cfg_byte(0, 7<<3|3, 0x06, 0x01);
-    pci_write_cfg_byte(0, 7<<3|3, 0x41, 0x12);
-    pci_write_cfg_byte(0, 7<<3|3, 0x42, 0x03);
-    pci_write_cfg_byte(0, 7<<3|3, PCI_LATENCY_TIMER, 0x40);
-
-
-}
diff --git a/board/MAI/AmigaOneG3SE/via686.h b/board/MAI/AmigaOneG3SE/via686.h
deleted file mode 100644
index 2a06a05..0000000
--- a/board/MAI/AmigaOneG3SE/via686.h
+++ /dev/null
@@ -1,29 +0,0 @@
-#ifndef VIA686_H_
-#define VIA686_H_
-
-
-#define CMOS_ADDR         0x70
-#define CMOS_DATA         0x71
-
-#define I8259_MASTER_CONTROL 0x20
-#define I8259_MASTER_MASK    0x21
-
-#define I8259_SLAVE_CONTROL  0xA0
-#define I8259_SLAVE_MASK     0xA1
-
-#define SIO_CONFIG_ADDR 0x3F0
-#define SIO_CONFIG_DATA 0x3F1
-
-#define SIO_WRITE_CONFIG(addr, byte) \
-   out_byte(SIO_CONFIG_ADDR, addr);  \
-   out_byte(SIO_CONFIG_DATA, byte);
-
-#define SIO_READ_CONFIG(addr, byte) \
-   out_byte(SIO_CONFIG_ADDR, addr); \
-   byte = in_byte(SIO_CONFIG_DATA);
-
-void via_init(void);
-
-void via_calibrate_bus_freq(void);
-
-#endif
diff --git a/board/MAI/AmigaOneG3SE/video.c b/board/MAI/AmigaOneG3SE/video.c
deleted file mode 100644
index e24e28b..0000000
--- a/board/MAI/AmigaOneG3SE/video.c
+++ /dev/null
@@ -1,541 +0,0 @@
-/*
- * (C) Copyright 2002
- * Hyperion Entertainment, Hans-JoergF@hyperion-entertainment.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <stdio_dev.h>
-#include "memio.h"
-#include <part.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-unsigned char *cursor_position;
-unsigned int cursor_row;
-unsigned int cursor_col;
-
-unsigned char current_attr;
-
-unsigned int video_numrows = 25;
-unsigned int video_numcols = 80;
-unsigned int video_scrolls = 0;
-
-#define VIDEO_BASE (unsigned char *)0xFD0B8000
-#define VIDEO_ROWS video_numrows
-#define VIDEO_COLS video_numcols
-#define VIDEO_PITCH (2 * video_numcols)
-#define VIDEO_SIZE (video_numrows * video_numcols * 2)
-#define VIDEO_NAME "vga"
-
-void video_test(void);
-void video_putc(char ch);
-void video_puts(char *string);
-void video_scroll(int rows);
-void video_banner(void);
-int  video_init(void);
-int  video_start(void);
-int  video_rows(void);
-int  video_cols(void);
-
-char *prompt_string = "=>";
-unsigned char video_get_attr(void);
-
-void video_set_color(unsigned char attr)
-{
-    unsigned char *fb = (unsigned char *)VIDEO_BASE;
-    int i;
-
-    current_attr = video_get_attr();
-
-    for (i=0; i<VIDEO_SIZE; i+=2)
-    {
-	*(fb+i+1) = current_attr;
-    }
-}
-
-unsigned char video_get_attr(void)
-{
-    char *s;
-    unsigned char attr;
-
-    attr = 0x0f;
-
-    s = getenv("vga_fg_color");
-    if (s)
-    {
-	attr = atoi(s);
-    }
-
-    s = getenv("vga_bg_color");
-    if (s)
-    {
-	attr |= atoi(s)<<4;
-    }
-
-    return attr;
-}
-
-int video_inited = 0;
-
-int drv_video_init(void)
-{
-    int error, devices = 1 ;
-    struct stdio_dev vgadev ;
-    if (video_inited) return 1;
-    video_inited = 1;
-    video_init();
-    memset (&vgadev, 0, sizeof(vgadev));
-
-    strcpy(vgadev.name, VIDEO_NAME);
-    vgadev.flags =  DEV_FLAGS_OUTPUT | DEV_FLAGS_SYSTEM;
-    vgadev.putc = video_putc;
-    vgadev.puts = video_puts;
-    vgadev.getc = NULL;
-    vgadev.tstc = NULL;
-    vgadev.start = video_start;
-
-    error = stdio_register (&vgadev);
-
-    if (error == 0)
-    {
-	char *s = getenv("stdout");
-	if (s && strcmp(s, VIDEO_NAME)==0)
-	{
-	    if (overwrite_console()) return 1;
-	    error = console_assign(stdout, VIDEO_NAME);
-	    if (error == 0) return 1;
-	    else return error;
-	}
-	return 1;
-    }
-
-    return error;
-}
-
-int video_init(void)
-{
-    cursor_position = VIDEO_BASE; /* Color text display base */
-    cursor_row = 0;
-    cursor_col = 0;
-    current_attr = video_get_attr(); /* Currently selected value for attribute. */
-/*    video_test(); */
-    video_set_color(current_attr);
-
-    return 0;
-}
-
-void video_set_cursor(int line, int column)
-{
-    unsigned short offset = line*video_numcols + column;
-    cursor_position = VIDEO_BASE +  line*VIDEO_PITCH + column*2;
-    out_byte(0x3D4, 0x0E);
-    out_byte(0x3D5, offset/256);
-    out_byte(0x3D4, 0x0F);
-    out_byte(0x3D5, offset%256);
-}
-
-void video_write_char(int character)
-{
-    *cursor_position = character;
-    *(cursor_position+1) = current_attr;
-}
-
-void video_test(void)
-{
-
-}
-
-void video_putc(char ch)
-{
-    switch(ch)
-    {
-    case '\n':
-	cursor_col = 0;
-	cursor_row += 1;
-	break;
-    case '\r':
-	cursor_col = 0;
-	break;
-    case '\b':
-	if (cursor_col) cursor_col--;
-	else return;
-	break;
-    case '\t':
-	cursor_col = (cursor_col/8+1)*8;
-	break;
-    default:
-	video_write_char(ch);
-	cursor_col++;
-	if (cursor_col > VIDEO_COLS-1)
-	{
-	    cursor_row++;
-	    cursor_col=0;
-	}
-    }
-
-    if (cursor_row > VIDEO_ROWS-1)
-	video_scroll(1);
-    video_set_cursor(cursor_row, cursor_col);
-}
-
-void video_scroll(int rows)
-{
-    unsigned short clear = ((unsigned short)current_attr) | (' '<<8);
-    unsigned short* addr16 = &((unsigned short *)VIDEO_BASE)[(VIDEO_ROWS-rows)*VIDEO_COLS];
-    int i;
-    char *s;
-
-    s = getenv("vga_askscroll");
-    video_scrolls += rows;
-
-    if (video_scrolls >= video_numrows)
-    {
-	if (s && strcmp(s, "yes"))
-	{
-	    while (-1 == tstc());
-	}
-
-	video_scrolls = 0;
-    }
-
-
-    memcpy(VIDEO_BASE, VIDEO_BASE+rows*(VIDEO_COLS*2), (VIDEO_ROWS-rows)*(VIDEO_COLS*2));
-    for (i = 0 ; i < rows * VIDEO_COLS ; i++)
-	addr16[i] = clear;
-    cursor_row-=rows;
-    cursor_col=0;
-}
-
-void video_puts(char *string)
-{
-    while (*string)
-    {
-	video_putc(*string);
-	string++;
-    }
-}
-
-int video_start(void)
-{
-    return 0;
-}
-
-unsigned char video_single_box[] =
-{
-    218, 196, 191,
-    179,      179,
-    192, 196, 217
-};
-
-unsigned char video_double_box[] =
-{
-    201, 205, 187,
-    186,      186,
-    200, 205, 188
-};
-
-unsigned char video_single_title[] =
-{
-    195, 196, 180, 180, 195
-};
-
-unsigned char video_double_title[] =
-{
-    204, 205, 185, 181, 198
-};
-
-#define SINGLE_BOX 0
-#define DOUBLE_BOX 1
-
-unsigned char *video_addr(int x, int y)
-{
-    return VIDEO_BASE + 2*(VIDEO_COLS*y) + 2*x;
-}
-
-void video_bios_print_string(char *s, int x, int y, int attr, int count)
-{
-    int cattr = current_attr;
-    if (attr != -1) current_attr = attr;
-    video_set_cursor(x,y);
-    while (count)
-    {
-	char c = *s++;
-	if (attr == -1) current_attr = *s++;
-	video_putc(c);
-	count--;
-    }
-}
-
-void video_draw_box(int style, int attr, char *title, int separate, int x, int y, int w, int h)
-{
-    unsigned char *fb, *fb2;
-    unsigned char *st = (style == SINGLE_BOX)?video_single_box : video_double_box;
-    unsigned char *ti = (style == SINGLE_BOX)?video_single_title : video_double_title;
-    int i;
-
-    fb = video_addr(x,y);
-    *(fb) = st[0];
-    *(fb+1) = attr;
-    fb += 2;
-
-    fb2 = video_addr(x,y+h-1);
-    *(fb2) = st[5];
-    *(fb2+1) = attr;
-    fb2 += 2;
-
-    for (i=0; i<w-2;i++)
-    {
-	*fb = st[1];
-	fb++;
-	*fb = attr;
-	fb++;
-
-	*fb2 = st[6];
-	fb2++;
-	*fb2 = attr;
-	fb2++;
-
-    }
-    *fb = st[2];
-    *(fb+1) = attr;
-
-    *fb2 = st[7];
-    *(fb2+1) = attr;
-
-    fb  = video_addr(x, y+1);
-    fb2 = video_addr(x+w-1, y+1);
-    for (i=0; i<h-2; i++)
-    {
-	*fb = st[3];
-	*(fb+1) = attr; fb += 2*VIDEO_COLS;
-
-	*fb2 = st[4];
-	*(fb2+1) = attr; fb2 += 2*VIDEO_COLS;
-    }
-
-    /* Draw title */
-    if (title)
-    {
-	if (separate == 0)
-	{
-	    fb = video_addr(x+1, y);
-	    *fb = ti[3];
-	    fb += 2;
-	    *fb = ' ';
-	    fb += 2;
-	    while (*title)
-	    {
-		*fb = *title;
-		fb ++;
-		*fb = attr;
-		fb++; title++;
-	    }
-	    *fb = ' ';
-	    fb += 2;
-	    *fb = ti[4];
-	}
-	else
-	{
-	    fb = video_addr(x, y+2);
-	    *fb = ti[0];
-	    fb += 2;
-	    for (i=0; i<w-2; i++)
-	    {
-		*fb = ti[1];
-		*(fb+1) = attr;
-		fb += 2;
-	    }
-	    *fb = ti[2];
-	    *(fb+1) = attr;
-	    fb = video_addr(x+1, y+1);
-	    for (i=0; i<w-2; i++)
-	    {
-		*fb = ' ';
-		*(fb+1) = attr;
-		fb += 2;
-	    }
-	    fb = video_addr(x+2, y+1);
-
-	    while (*title)
-	    {
-		*fb = *title;
-		*(fb+1) = attr;
-		fb += 2;
-		title++;
-	    }
-	}
-    }
-
-}
-
-void video_draw_text(int x, int y, int attr, char *text)
-{
-    unsigned char *fb = video_addr(x,y);
-    while (*text)
-    {
-	*fb++ = *text++;
-	*fb++ = attr;
-    }
-}
-
-void video_save_rect(int x, int y, int w, int h, void *save_area, int clearchar, int clearattr)
-{
-    unsigned char *save = (unsigned char *)save_area;
-    unsigned char *fb = video_addr(x,y);
-    int i,j;
-    for (i=0; i<h; i++)
-    {
-	unsigned char *fbb = fb;
-	for (j=0; j<w; j++)
-	{
-	    *save ++ = *fb;
-	    if (clearchar > 0) *fb = clearchar;
-	    fb ++;
-	    *save ++ = *fb;
-	    if (clearattr > 0) *fb = clearattr;
-	}
-	fb = fbb + 2*VIDEO_COLS;
-    }
-}
-
-void video_restore_rect(int x, int y, int w, int h, void *save_area)
-{
-    unsigned char *save = (unsigned char *)save_area;
-    unsigned char *fb = video_addr(x,y);
-    int i,j;
-    for (i=0; i<h; i++)
-    {
-	unsigned char *fbb = fb;
-	for (j=0; j<w; j++)
-	{
-	    *fb ++ = *save ++;
-	    *fb ++ = *save ++;
-	}
-	fb = fbb + 2*VIDEO_COLS;
-    }
-
-}
-
-int video_rows(void)
-{
-    return VIDEO_ROWS;
-}
-
-int video_cols(void)
-{
-    return VIDEO_COLS;
-}
-
-void video_size(int cols, int rows)
-{
-    video_numrows = rows;
-    video_numcols = cols;
-}
-
-void video_clear(void)
-{
-    unsigned short *fbb = (unsigned short *)0xFD0B8000;
-    int i,j;
-    unsigned short val = 0x2000 | current_attr;
-
-    for (i=0; i<video_rows(); i++)
-    {
-	for (j=0; j<video_cols(); j++)
-	{
-	    *fbb++ = val;
-	}
-    }
-    video_set_cursor(0,0);
-    cursor_row = 0;
-    cursor_col = 0;
-}
-
-#ifdef EASTEREGG
-int video_easteregg_active = 0;
-
-void video_easteregg(void)
-{
-    video_easteregg_active = 1;
-}
-#endif
-
-extern block_dev_desc_t * ide_get_dev(int dev);
-extern char version_string[];
-
-void video_banner(void)
-{
-    block_dev_desc_t *ide;
-    int i;
-    char *s;
-    int maxdev;
-
-
-    if (video_inited == 0) return;
-#ifdef EASTEREGG
-    if (video_easteregg_active)
-    {
-	prompt_string="";
-	video_clear();
-	printf("\n");
-	printf("    **** COMMODORE 64 BASIC X2 ****\n\n");
-	printf(" 64K RAM SYSTEM  38911 BASIC BYTES FREE\n\n");
-	printf("READY\n");
-    }
-    else
-    {
-#endif
-	s = getenv("ide_maxbus");
-	if (s)
-	    maxdev = atoi(s) * 2;
-	else
-	    maxdev = 4;
-
-	s = getenv("stdout");
-	if (s && strcmp(s, "serial") == 0)
-	    return;
-
-	video_clear();
-	printf("%s\n\nCPU: ", version_string);
-	checkcpu();
-	printf("DRAM: %ld MB\n", gd->bd->bi_memsize/(1024*1024));
-	printf("FSB: %ld MHz\n", gd->bd->bi_busfreq/1000000);
-
-	printf("\n---- Disk summary ----\n");
-	for (i = 0; i < maxdev; i++)
-	{
-	    ide = ide_get_dev(i);
-	    printf("Device %d: ", i);
-	    dev_print(ide);
-	}
-
-/*
-    video_draw_box(SINGLE_BOX, 0x0F, "Test 1", 0, 0,18, 72, 4);
-    video_draw_box(DOUBLE_BOX, 0x0F, "Test 2", 1, 4,10, 50, 6);
-    video_draw_box(DOUBLE_BOX, 0x0F, "Test 3", 0, 40, 3, 20, 5);
-
-    video_draw_text(1, 4, 0x2F, "Highlighted options");
-    video_draw_text(1, 5, 0x0F, "Non-selected option");
-    video_draw_text(1, 6, 0x07, "disabled option");
-*/
-#ifdef EASTEREGG
-    }
-#endif
-}
diff --git a/board/MAI/menu/cmd_menu.c b/board/MAI/menu/cmd_menu.c
deleted file mode 100644
index 2b97d23..0000000
--- a/board/MAI/menu/cmd_menu.c
+++ /dev/null
@@ -1,16 +0,0 @@
-#include <common.h>
-#include <command.h>
-
-int do_menu( cmd_tbl_t *cmdtp, /*bd_t *bd,*/ int flag, int argc, char *argv[] )
-{
-/*	printf("<NOT YET IMPLEMENTED>\n"); */
-	return 0;
-}
-
-#if defined(CONFIG_AMIGAONEG3SE) && defined(CONFIG_CMD_BSP)
-U_BOOT_CMD(
-	menu,   1,      1,      do_menu,
-	"display BIOS setup menu",
-	""
-);
-#endif
diff --git a/boards.cfg b/boards.cfg
index 6efde75..1a5cfb1 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -314,7 +314,6 @@ M5282EVB	m68k	mcf52x2		m5282evb	freescale
 M53017EVB	m68k	mcf52x2		m53017evb	freescale
 microblaze-generic	microblaze	microblaze	microblaze-generic	xilinx
 mpc7448hpc2	powerpc	74xx_7xx 	mpc7448hpc2	freescale
-AmigaOneG3SE	powerpc	74xx_7xx 	AmigaOneG3SE	MAI
 pdm360ng	powerpc	mpc512x
 mecp5123	powerpc	mpc512x		-		esd
 cmi_mpc5xx	powerpc	mpc5xx		cmi
diff --git a/common/cmd_bootm.c b/common/cmd_bootm.c
index 8803202..74ff205 100644
--- a/common/cmd_bootm.c
+++ b/common/cmd_bootm.c
@@ -635,15 +635,6 @@ int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	usb_stop();
 #endif
 
-#ifdef CONFIG_AMIGAONEG3SE
-	/*
-	 * We've possible left the caches enabled during
-	 * bios emulation, so turn them off again
-	 */
-	icache_disable();
-	dcache_disable();
-#endif
-
 	ret = bootm_load_os(images.os, &load_end, 1);
 
 	if (ret < 0) {
diff --git a/common/cmd_fdc.c b/common/cmd_fdc.c
index 8e18c71..4c16d19 100644
--- a/common/cmd_fdc.c
+++ b/common/cmd_fdc.c
@@ -183,31 +183,6 @@ static FDC_COMMAND_STRUCT cmd; /* global command struct */
 #define CONFIG_SYS_ISA_IO_OFFSET 0
 #endif
 
-
-#ifdef CONFIG_AMIGAONEG3SE
-unsigned char INT6_Status;
-
-void fdc_interrupt(void)
-{
-    INT6_Status = 0x80;
-}
-
-/* waits for an interrupt (polling) */
-int wait_for_fdc_int(void)
-{
-	unsigned long timeout;
-	timeout = FDC_TIME_OUT;
-	while(((volatile)INT6_Status & 0x80) == 0) {
-		timeout--;
-		udelay(10);
-		if(timeout == 0) /* timeout occured */
-			return FALSE;
-	}
-	INT6_Status = 0;
-	return TRUE;
-}
-#endif
-
 /* Supporting Functions */
 /* reads a Register of the FDC */
 unsigned char read_fdc_reg(unsigned int addr)
@@ -230,7 +205,6 @@ void write_fdc_reg(unsigned int addr, unsigned char val)
 	tmp[0]=val;
 }
 
-#ifndef CONFIG_AMIGAONEG3SE
 /* waits for an interrupt (polling) */
 int wait_for_fdc_int(void)
 {
@@ -245,8 +219,6 @@ int wait_for_fdc_int(void)
 	return TRUE;
 }
 
-#endif
-
 /* reads a byte from the FIFO of the FDC and checks direction and RQM bit
    of the MSR. returns -1 if timeout, or byte if ok */
 int read_fdc_byte(void)
@@ -438,7 +410,6 @@ int fdc_seek(FDC_COMMAND_STRUCT *pCMD,FD_GEO_STRUCT *pFG)
 	return(fdc_issue_cmd(pCMD,pFG));
 }
 
-#ifndef CONFIG_AMIGAONEG3SE
 /* terminates current command, by not servicing the FIFO
  * waits for interrupt and fills in the result bytes */
 int fdc_terminate(FDC_COMMAND_STRUCT *pCMD)
@@ -452,27 +423,6 @@ int fdc_terminate(FDC_COMMAND_STRUCT *pCMD)
 	}
 	return TRUE;
 }
-#endif
-#ifdef CONFIG_AMIGAONEG3SE
-int fdc_terminate(FDC_COMMAND_STRUCT *pCMD)
-{
-	int i;
-	for(i=0;i<100;i++)
-		udelay(500); /* wait 500usec for fifo overrun */
-	while((INT6_Status&0x80)==0x00); /* wait as long as no int has occured */
-	for(i=0;i<7;i++) {
-		pCMD->result[i]=(unsigned char)read_fdc_byte();
-	}
-	INT6_Status = 0;
-	return TRUE;
-}
-
-#endif
-
-#ifdef CONFIG_AMIGAONEG3SE
-#define disable_interrupts() 0
-#define enable_interrupts() (void)0
-#endif
 
 /* reads data from FDC, seek commands are issued automatic */
 int fdc_read_data(unsigned char *buffer, unsigned long blocks,FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG)
@@ -593,11 +543,6 @@ retrycal:
 	return TRUE;
 }
 
-#ifdef CONFIG_AMIGAONEG3SE
-#undef disable_interrupts()
-#undef enable_interrupts()
-#endif
-
 /* Scan all drives and check if drive is present and disk is inserted */
 int fdc_check_drive(FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG)
 {
@@ -647,11 +592,6 @@ int fdc_setup(int drive, FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG)
 {
 	int i;
 
-#ifdef CONFIG_AMIGAONEG3SE
-	irq_install_handler(6, (interrupt_handler_t *)fdc_interrupt, NULL);
-	i8259_unmask_irq(6);
-#endif
-
 #ifdef CONFIG_SYS_FDC_HW_INIT
 	fdc_hw_init ();
 #endif
diff --git a/common/cmd_ide.c b/common/cmd_ide.c
index 093ca9f..8bd8920 100644
--- a/common/cmd_ide.c
+++ b/common/cmd_ide.c
@@ -119,31 +119,22 @@ ulong ide_bus_offset[CONFIG_SYS_IDE_MAXBUS] = {
 };
 
 
-#ifndef CONFIG_AMIGAONEG3SE
 static int ide_bus_ok[CONFIG_SYS_IDE_MAXBUS];
-#else
-static int ide_bus_ok[CONFIG_SYS_IDE_MAXBUS] = {0,};
-#endif
 
 block_dev_desc_t ide_dev_desc[CONFIG_SYS_IDE_MAXDEVICE];
 /* ------------------------------------------------------------------------- */
 
 #ifdef CONFIG_IDE_LED
-#if !defined(CONFIG_KUP4K) &&  !defined(CONFIG_KUP4X) &&!defined(CONFIG_BMS2003) &&!defined(CONFIG_CPC45)
+# if !defined(CONFIG_BMS2003)	&& \
+     !defined(CONFIG_CPC45)	&& \
+     !defined(CONFIG_KUP4K) && \
+     !defined(CONFIG_KUP4X)
 static void  ide_led   (uchar led, uchar status);
 #else
 extern void  ide_led   (uchar led, uchar status);
 #endif
 #else
-#ifndef CONFIG_AMIGAONEG3SE
 #define ide_led(a,b)	/* dummy */
-#else
-extern void ide_led(uchar led, uchar status);
-#define LED_IDE1  1
-#define LED_IDE2  2
-#define CONFIG_IDE_LED 1
-#define DEVICE_LED(x) 1
-#endif
 #endif
 
 #ifdef CONFIG_IDE_RESET
@@ -562,13 +553,10 @@ void ide_init (void)
 #endif
 	unsigned char c;
 	int i, bus;
-#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+#if defined(CONFIG_SC3)
 	unsigned int ata_reset_time = ATA_RESET_TIME;
 	char *s;
 #endif
-#ifdef CONFIG_AMIGAONEG3SE
-	unsigned int max_bus_scan;
-#endif
 #ifdef CONFIG_IDE_8xx_PCCARD
 	extern int pcmcia_on (void);
 	extern int ide_devices_found; /* Initialized in check_ide_device() */
@@ -638,19 +626,8 @@ void ide_init (void)
 	 * Wait for IDE to get ready.
 	 * According to spec, this can take up to 31 seconds!
 	 */
-#ifndef CONFIG_AMIGAONEG3SE
 	for (bus=0; bus<CONFIG_SYS_IDE_MAXBUS; ++bus) {
 		int dev = bus * (CONFIG_SYS_IDE_MAXDEVICE / CONFIG_SYS_IDE_MAXBUS);
-#else
-	s = getenv("ide_maxbus");
-	if (s)
-		max_bus_scan = simple_strtol(s, NULL, 10);
-	else
-		max_bus_scan = CONFIG_SYS_IDE_MAXBUS;
-
-	for (bus=0; bus<max_bus_scan; ++bus) {
-		int dev = bus * (CONFIG_SYS_IDE_MAXDEVICE / max_bus_scan);
-#endif
 
 #ifdef CONFIG_IDE_8xx_PCCARD
 		/* Skip non-ide devices from probing */
@@ -668,30 +645,19 @@ void ide_init (void)
 		udelay (100000);		/* 100 ms */
 		ide_outb (dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
 		udelay (100000);		/* 100 ms */
-#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
-		if ((s = getenv("ide_reset_timeout")) != NULL)
-			ata_reset_time = simple_strtol(s, NULL, 10);
-#endif
 		i = 0;
 		do {
 			udelay (10000);		/* 10 ms */
 
 			c = ide_inb (dev, ATA_STATUS);
 			i++;
-#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+#if defined(CONFIG_SC3)
 			if (i > (ata_reset_time * 100)) {
 #else
 			if (i > (ATA_RESET_TIME * 100)) {
 #endif
 				puts ("** Timeout **\n");
 				ide_led ((LED_IDE1 | LED_IDE2), 0); /* LED's off */
-#ifdef CONFIG_AMIGAONEG3SE
-				/* If this is the second bus, the first one was OK */
-				if (bus != 0) {
-					ide_bus_ok[bus] = 0;
-					goto skip_bus;
-				}
-#endif
 				return;
 			}
 			if ((i >= 100) && ((i%100)==0)) {
@@ -714,9 +680,6 @@ void ide_init (void)
 		WATCHDOG_RESET();
 	}
 
-#ifdef CONFIG_AMIGAONEG3SE
-      skip_bus:
-#endif
 	putc ('\n');
 
 	ide_led ((LED_IDE1 | LED_IDE2), 0);	/* LED's off	*/
@@ -1010,10 +973,6 @@ static void ide_ident (block_dev_desc_t *dev_desc)
 	unsigned char c;
 	hd_driveid_t *iop = (hd_driveid_t *)iobuf;
 
-#ifdef CONFIG_AMIGAONEG3SE
-	int max_bus_scan;
-	char *s;
-#endif
 #ifdef CONFIG_ATAPI
 	int retries = 0;
 	int do_retry = 0;
@@ -1030,19 +989,6 @@ static void ide_ident (block_dev_desc_t *dev_desc)
 	device=dev_desc->dev;
 	printf ("  Device %d: ", device);
 
-#ifdef CONFIG_AMIGAONEG3SE
-	s = getenv("ide_maxbus");
-	if (s) {
-		max_bus_scan = simple_strtol(s, NULL, 10);
-	} else {
-		max_bus_scan = CONFIG_SYS_IDE_MAXBUS;
-	}
-	if (device >= max_bus_scan*2) {
-		dev_desc->type=DEV_TYPE_UNKNOWN;
-		return;
-	}
-#endif
-
 	ide_led (DEVICE_LED(device), 1);	/* LED on	*/
 	/* Select device
 	 */
@@ -1086,10 +1032,6 @@ static void ide_ident (block_dev_desc_t *dev_desc)
 	if (((c & ATA_STAT_DRQ) == 0) ||
 	    ((c & (ATA_STAT_FAULT|ATA_STAT_ERR)) != 0) ) {
 #ifdef CONFIG_ATAPI
-#ifdef CONFIG_AMIGAONEG3SE
-		s = getenv("ide_doreset");
-		if (s && strcmp(s, "on") == 0)
-#endif
 		{
 			/* Need to soft reset the device in case it's an ATAPI...  */
 			debug ("Retrying...\n");
@@ -1601,7 +1543,6 @@ static void ide_reset (void)
 /* ------------------------------------------------------------------------- */
 
 #if defined(CONFIG_IDE_LED)	&& \
-   !defined(CONFIG_AMIGAONEG3SE)&& \
    !defined(CONFIG_CPC45)	&& \
    !defined(CONFIG_HMI10)	&& \
    !defined(CONFIG_KUP4K)	&& \
@@ -1758,9 +1699,6 @@ unsigned char atapi_issue(int device,unsigned char* ccb,int ccblen, unsigned cha
 	 */
 	mask = ATA_STAT_BUSY|ATA_STAT_DRQ;
 	res = 0;
-#ifdef	CONFIG_AMIGAONEG3SE
-# warning THF: Removed LBA mode ???
-#endif
 	ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
 	c = atapi_wait_mask(device,ATAPI_TIME_OUT,mask,res);
 	if ((c & mask) != res) {
@@ -1774,9 +1712,6 @@ unsigned char atapi_issue(int device,unsigned char* ccb,int ccblen, unsigned cha
 	ide_outb (device, ATA_SECT_NUM, 0);
 	ide_outb (device, ATA_CYL_LOW,  (unsigned char)(buflen & 0xFF));
 	ide_outb (device, ATA_CYL_HIGH, (unsigned char)((buflen>>8) & 0xFF));
-#ifdef	CONFIG_AMIGAONEG3SE
-# warning THF: Removed LBA mode ???
-#endif
 	ide_outb (device, ATA_DEV_HD,   ATA_LBA | ATA_DEVICE(device));
 
 	ide_outb (device, ATA_COMMAND,  ATAPI_CMD_PACKET);
@@ -1875,16 +1810,6 @@ unsigned char atapi_issue_autoreq (int device,
 	unsigned char res,key,asc,ascq;
 	int notready,unitattn;
 
-#ifdef CONFIG_AMIGAONEG3SE
-	char *s;
-	unsigned int timeout, retrycnt;
-
-	s = getenv("ide_cd_timeout");
-	timeout = s ? (simple_strtol(s, NULL, 10)*1000000)/5 : 0;
-
-	retrycnt = 0;
-#endif
-
 	unitattn=ATAPI_UNIT_ATTN;
 	notready=ATAPI_DRIVE_NOT_READY;
 
@@ -1939,25 +1864,6 @@ retry:
 		goto error;
 	}
 
-#ifdef CONFIG_AMIGAONEG3SE
-	if ((sense_data[2]&0xF)==0x0B) {
-		debug ("ABORTED COMMAND...retry\n");
-		if (retrycnt++ < 4)
-			goto retry;
-		return (0xFF);
-	}
-
-	if ((sense_data[2]&0xf) == 0x02 &&
-	    sense_data[12] == 0x04	&&
-	    sense_data[13] == 0x01	) {
-		debug ("Waiting for unit to become active\n");
-		udelay(timeout);
-		if (retrycnt++ < 4)
-			goto retry;
-		return 0xFF;
-	}
-#endif	/* CONFIG_AMIGAONEG3SE */
-
 	printf ("ERROR: Unknown Sense key %02X ASC %02X ASCQ %02X\n",key,asc,ascq);
 error:
 	debug  ("ERROR Sense key %02X ASC %02X ASCQ %02X\n",key,asc,ascq);
diff --git a/common/cmd_nvedit.c b/common/cmd_nvedit.c
index eb89e9e..d2ef217 100644
--- a/common/cmd_nvedit.c
+++ b/common/cmd_nvedit.c
@@ -385,18 +385,6 @@ int _do_setenv (int flag, int argc, char *argv[])
 		return 0;
 	}
 #endif
-
-#ifdef CONFIG_AMIGAONEG3SE
-	if (strcmp(argv[1], "vga_fg_color") == 0 ||
-	    strcmp(argv[1], "vga_bg_color") == 0 ) {
-		extern void video_set_color(unsigned char attr);
-		extern unsigned char video_get_attr(void);
-
-		video_set_color(video_get_attr());
-		return 0;
-	}
-#endif	/* CONFIG_AMIGAONEG3SE */
-
 	return 0;
 }
 
diff --git a/common/console.c b/common/console.c
index 51c6fb6..b09b7d1 100644
--- a/common/console.c
+++ b/common/console.c
@@ -29,10 +29,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_AMIGAONEG3SE
-int console_changed = 0;
-#endif
-
 #ifdef CONFIG_SYS_CONSOLE_IS_IN_ENV
 /*
  * if overwrite_console returns 1, the stdin, stderr and stdout
diff --git a/common/env_common.c b/common/env_common.c
index 439a4a9..82e4936 100644
--- a/common/env_common.c
+++ b/common/env_common.c
@@ -32,11 +32,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_AMIGAONEG3SE
-	extern void enable_nvram(void);
-	extern void disable_nvram(void);
-#endif
-
 #undef DEBUG_ENV
 #ifdef DEBUG_ENV
 #define DEBUGF(fmt,args...) printf(fmt ,##args)
@@ -159,20 +154,6 @@ static uchar env_get_char_init (int index)
 	return (c);
 }
 
-#ifdef CONFIG_AMIGAONEG3SE
-uchar env_get_char_memory (int index)
-{
-	uchar retval;
-	enable_nvram();
-	if (gd->env_valid) {
-		retval = ( *((uchar *)(gd->env_addr + index)) );
-	} else {
-		retval = ( default_environment[index] );
-	}
-	disable_nvram();
-	return retval;
-}
-#else
 uchar env_get_char_memory (int index)
 {
 	if (gd->env_valid) {
@@ -181,7 +162,6 @@ uchar env_get_char_memory (int index)
 		return ( default_environment[index] );
 	}
 }
-#endif
 
 uchar env_get_char (int index)
 {
@@ -229,10 +209,6 @@ void env_relocate (void)
 		gd->reloc_off);
 #endif
 
-#ifdef CONFIG_AMIGAONEG3SE
-	enable_nvram();
-#endif
-
 #ifdef ENV_IS_EMBEDDED
 	/*
 	 * The environment buffer is embedded with the text segment,
@@ -263,10 +239,6 @@ void env_relocate (void)
 		env_relocate_spec ();
 	}
 	gd->env_addr = (ulong)&(env_ptr->data);
-
-#ifdef CONFIG_AMIGAONEG3SE
-	disable_nvram();
-#endif
 }
 
 #ifdef CONFIG_AUTO_COMPLETE
diff --git a/common/env_nvram.c b/common/env_nvram.c
index 2628fe4..7c7cf98 100644
--- a/common/env_nvram.c
+++ b/common/env_nvram.c
@@ -59,24 +59,6 @@ char * env_name_spec = "NVRAM";
 
 extern uchar default_environment[];
 
-#ifdef CONFIG_AMIGAONEG3SE
-uchar env_get_char_spec (int index)
-{
-#ifdef CONFIG_SYS_NVRAM_ACCESS_ROUTINE
-	uchar c;
-
-	nvram_read(&c, CONFIG_ENV_ADDR+index, 1);
-
-	return c;
-#else
-	uchar retval;
-	enable_nvram();
-	retval = *((uchar *)(gd->env_addr + index));
-	disable_nvram();
-	return retval;
-#endif
-}
-#else
 uchar env_get_char_spec (int index)
 {
 #ifdef CONFIG_SYS_NVRAM_ACCESS_ROUTINE
@@ -89,7 +71,6 @@ uchar env_get_char_spec (int index)
 	return *((uchar *)(gd->env_addr + index));
 #endif
 }
-#endif
 
 void env_relocate_spec (void)
 {
@@ -103,19 +84,12 @@ void env_relocate_spec (void)
 int saveenv (void)
 {
 	int rcode = 0;
-#ifdef CONFIG_AMIGAONEG3SE
-	enable_nvram();
-#endif
 #ifdef CONFIG_SYS_NVRAM_ACCESS_ROUTINE
 	nvram_write(CONFIG_ENV_ADDR, env_ptr, CONFIG_ENV_SIZE);
 #else
 	if (memcpy ((char *)CONFIG_ENV_ADDR, env_ptr, CONFIG_ENV_SIZE) == NULL)
 		    rcode = 1 ;
 #endif
-#ifdef CONFIG_AMIGAONEG3SE
-	udelay(10000);
-	disable_nvram();
-#endif
 	return rcode;
 }
 
@@ -127,9 +101,6 @@ int saveenv (void)
  */
 int env_init (void)
 {
-#ifdef CONFIG_AMIGAONEG3SE
-	enable_nvram();
-#endif
 #if defined(CONFIG_SYS_NVRAM_ACCESS_ROUTINE)
 	ulong crc;
 	uchar data[ENV_SIZE];
@@ -147,8 +118,5 @@ int env_init (void)
 		gd->env_addr  = (ulong)&default_environment[0];
 		gd->env_valid = 0;
 	}
-#ifdef CONFIG_AMIGAONEG3SE
-	disable_nvram();
-#endif
 	return (0);
 }
diff --git a/common/main.c b/common/main.c
index f7e7c1c..3760ba3 100644
--- a/common/main.c
+++ b/common/main.c
@@ -427,14 +427,7 @@ void main_loop (void)
 	    }
 	}
 #endif /* CONFIG_MENUKEY */
-#endif	/* CONFIG_BOOTDELAY */
-
-#ifdef CONFIG_AMIGAONEG3SE
-	{
-	    extern void video_banner(void);
-	    video_banner();
-	}
-#endif
+#endif /* CONFIG_BOOTDELAY */
 
 	/*
 	 * Main Loop for Monitor Command Processing
diff --git a/drivers/rtc/mc146818.c b/drivers/rtc/mc146818.c
index d68b438..ac4eb6a 100644
--- a/drivers/rtc/mc146818.c
+++ b/drivers/rtc/mc146818.c
@@ -67,9 +67,6 @@ int rtc_get (struct rtc_time *tmp)
 	wday	= rtc_read (RTC_DAY_OF_WEEK);
 	mon	= rtc_read (RTC_MONTH);
 	year	= rtc_read (RTC_YEAR);
-#ifdef CONFIG_AMIGAONEG3SE
-	wday -= 1; /* VIA 686 stores Sunday = 1, Monday = 2, ... */
-#endif
 #ifdef RTC_DEBUG
 	printf ( "Get RTC year: %02x mon/cent: %02x mday: %02x wday: %02x "
 		"hr: %02x min: %02x sec: %02x\n",
@@ -114,11 +111,7 @@ int rtc_set (struct rtc_time *tmp)
 
 	rtc_write (RTC_YEAR, bin2bcd(tmp->tm_year % 100));
 	rtc_write (RTC_MONTH, bin2bcd(tmp->tm_mon));
-#ifdef CONFIG_AMIGAONEG3SE
-	rtc_write (RTC_DAY_OF_WEEK, bin2bcd(tmp->tm_wday)+1);
-#else
 	rtc_write (RTC_DAY_OF_WEEK, bin2bcd(tmp->tm_wday));
-#endif
 	rtc_write (RTC_DATE_OF_MONTH, bin2bcd(tmp->tm_mday));
 	rtc_write (RTC_HOURS, bin2bcd(tmp->tm_hour));
 	rtc_write (RTC_MINUTES, bin2bcd(tmp->tm_min ));
diff --git a/drivers/rtc/mk48t59.c b/drivers/rtc/mk48t59.c
index b176882..e285823 100644
--- a/drivers/rtc/mk48t59.c
+++ b/drivers/rtc/mk48t59.c
@@ -63,24 +63,6 @@ static void rtc_write (short reg, uchar val)
 	out8(RTC(reg),val);
 }
 
-#elif defined(CONFIG_AMIGAONEG3SE)
-
-#include "../board/MAI/AmigaOneG3SE/via686.h"
-#include "../board/MAI/AmigaOneG3SE/memio.h"
-
-
-static uchar rtc_read (short reg)
-{
-    out_byte(CMOS_ADDR, (uint8)reg);
-    return in_byte(CMOS_DATA);
-}
-
-static void rtc_write (short reg, uchar val)
-{
-    out_byte(CMOS_ADDR, (uint8)reg);
-    out_byte(CMOS_DATA, (uint8)val);
-}
-
 #elif defined(CONFIG_EVAL5200)
 
 static uchar rtc_read (short reg)
diff --git a/include/configs/AmigaOneG3SE.h b/include/configs/AmigaOneG3SE.h
deleted file mode 100644
index 0dfb23b..0000000
--- a/include/configs/AmigaOneG3SE.h
+++ /dev/null
@@ -1,404 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- *
- * Configuration settings for the AmigaOneG3SE board.
- *
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_AMIGAONEG3SE	1
-
-#define CONFIG_BOARD_EARLY_INIT_F 1
-#define CONFIG_MISC_INIT_R	1
-
-#define CONFIG_VERY_BIG_RAM	1
-
-#define CONFIG_CONS_INDEX	1
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-#undef CONFIG_CLOCKS_IN_MHZ		/* clocks passed to Linux in Hz */
-
-#define CONFIG_BOOTARGS		"root=/dev/ram rw ramdisk_size=4096"
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_AMIGA_PARTITION
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FDC
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_PCI
-
-
-#define CONFIG_PCI		1
-/* #define CONFIG_PCI_SCAN_SHOW 1 */
-#define CONFIG_PCI_PNP		1	/* PCI plug-and-play */
-
-#define atoi(x)		simple_strtoul(x,NULL,10)
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT	"] "		/* Monitor Command Prompt	*/
-
-#define CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-/* #undef CONFIG_SYS_HUSH_PARSER */
-#ifdef	CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#endif
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-
-/* Print Buffer Size
- */
-#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-
-#define CONFIG_SYS_MAXARGS	64		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR	0x00500000	/* Default load address		*/
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE	    0x00000000
-#define CONFIG_SYS_FLASH_BASE	    0xFFF00000
-#define CONFIG_SYS_FLASH_MAX_SIZE  0x00080000
-/* Maximum amount of RAM.
- */
-#define CONFIG_SYS_MAX_RAM_SIZE    0x80000000	/* 2G			*/
-
-#define CONFIG_SYS_RESET_ADDRESS   0xFFF00100
-
-#define CONFIG_SYS_MONITOR_BASE    TEXT_BASE
-
-#define CONFIG_SYS_MONITOR_LEN	    (768 << 10) /* Reserve 512 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN	    (2500 << 10) /* Reserve 128 kB for malloc() */
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_SDRAM_BASE && \
-    CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MAX_RAM_SIZE
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x02000000	/* 0 ... 32 MB in DRAM	*/
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-
-/* Size in bytes reserved for initial data
- */
-/* HJF: used to be 0x400000 */
-#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
-#define CONFIG_SYS_INIT_RAM_END	0x8000
-#define CONFIG_SYS_GBL_DATA_SIZE	128
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-
-/*
- * Temporary buffer for serial data until the real serial driver
- * is initialised (memtest will destroy this buffer)
- */
-#define CONFIG_SYS_SCONSOLE_ADDR     CONFIG_SYS_INIT_RAM_ADDR
-#define CONFIG_SYS_SCONSOLE_SIZE     0x0002000
-
-/* SDRAM 0 - 256MB
- */
-
-/*HJF: #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U*/
-
-#define CONFIG_SYS_DBAT0L	      (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_DBAT0U	      (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT0L      (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U      (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-/* PCI Range
- */
-#define CONFIG_SYS_DBAT1L	 (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT1U	 (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT1L	 (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT1U	 (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-/* HJF:
-#define CONFIG_SYS_IBAT1L ((CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_INIT_RAM_ADDR) | BATL_PP_RW)
-#define CONFIG_SYS_IBAT1U ((CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_INIT_RAM_ADDR) | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT1L ((CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_INIT_RAM_ADDR + 0x20000) | BATL_PP_RW )
-#define CONFIG_SYS_DBAT1U ((CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_INIT_RAM_ADDR + 0x20000) | BATU_BL_256M | BATU_VS | BATU_VP)
-*/
-
-/* Init RAM in the CPU DCache (no backing memory)
- */
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_DBAT2U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-/* This used to be commented out */
-#define CONFIG_SYS_IBAT2L	  CONFIG_SYS_DBAT2L
-/* This here too */
-#define CONFIG_SYS_IBAT2U	  CONFIG_SYS_DBAT2U
-
-
-/* I/O and PCI memory at 0xf0000000
- */
-#define CONFIG_SYS_DBAT3L	(0xf0000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U	(0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT3L	(0xf0000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U	(0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- */
-#define CONFIG_SYS_HZ		1000
-#define CONFIG_SYS_BUS_HZ	133000000 /* bus speed - 100 mhz		*/
-#define CONFIG_SYS_CPU_CLK	133000000
-#define CONFIG_SYS_BUS_CLK	133000000
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* Max number of flash banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* Max number of sectors in one bank	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
-
-/*
- * Environment is stored in NVRAM.
- */
-#define CONFIG_ENV_IS_IN_NVRAM	1
-#define CONFIG_ENV_ADDR		0xFD0E0000 /* This should be 0xFD0E0000, but we skip bytes to
-					    * protect softex's settings for now.
-					    * Original 768 bytes where not enough.
-					    */
-#define CONFIG_ENV_SIZE		0x8000	   /* Size of the Environment. See comment above */
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1 /* stdin/stdout/stderr are in environment */
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE	1
-#define CONFIG_ENV_OVERWRITE 1
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*
- * L2 cache
- */
-#define CONFIG_SYS_L2
-#define L2_INIT	  (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
-		   L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
-#define L2_ENABLE (L2_INIT | L2CR_L2E)
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM		0x02	/* Software reboot			*/
-
-
-/*-----------------------------------------------------------------------
- * IDE ATAPI Configuration
- */
-
-#define CONFIG_ATAPI		1
-#define CONFIG_SYS_IDE_MAXBUS		2
-#define CONFIG_SYS_IDE_MAXDEVICE	4
-#define CONFIG_ISO_PARTITION	1
-
-#define CONFIG_SYS_ATA_BASE_ADDR	0xFE000000  /* was: via_get_base_addr() */
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x1F0
-#define CONFIG_SYS_ATA_IDE1_OFFSET	0x170
-
-#define CONFIG_SYS_ATA_REG_OFFSET	0
-#define CONFIG_SYS_ATA_DATA_OFFSET	0
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0200
-
-/*-----------------------------------------------------------------------
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_MAX_DOC_DEVICE	1	/* Max number of DOC devices		*/
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#undef CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
-/*-----------------------------------------------------------------------
-  RTC
-*/
-#define CONFIG_RTC_MC146818
-
-/*-----------------------------------------------------------------------
- * NS16550 Configuration
- */
-
-#define CONFIG_SYS_NS16550
-
-#define CONFIG_SYS_NS16550_COM1 0xFE0003F8
-#define CONFIG_SYS_NS16550_COM2 0xFE0002F8
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-/* base address for ISA I/O
- */
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xFE000000
-
-/* ISA Interrupt stuff (taken from JWL) */
-
-#define ISA_INT1_OCW1		0x21
-#define ISA_INT2_OCW1		0xA1
-#define ISA_INT1_OCW2		0x20
-#define ISA_INT2_OCW2		0xA0
-#define ISA_INT1_OCW3		0x20
-#define ISA_INT2_OCW3		0xA0
-
-#define ISA_INT1_ICW1		0x20
-#define ISA_INT2_ICW1		0xA0
-#define ISA_INT1_ICW2		0x21
-#define ISA_INT2_ICW2		0xA1
-#define ISA_INT1_ICW3		0x21
-#define ISA_INT2_ICW3		0xA1
-#define ISA_INT1_ICW4		0x21
-#define ISA_INT2_ICW4		0xA1
-
-
-/*
- * misc
- */
-
-#define CONFIG_NET_MULTI
-#define CONFIG_SYS_BOARD_ASM_INIT
-#define CONFIG_LAST_STAGE_INIT
-
-/* #define CONFIG_ETHADDR	00:09:D2:10:00:76 */
-/* #define CONFIG_IPADDR	192.168.0.2 */
-/* #define CONFIG_NETMASK	255.255.255.240 */
-/* #define CONFIG_GATEWAYIP	192.168.0.3 */
-
-#define CONFIG_3COM
-/* #define CONFIG_BOOTP_RANDOM_DELAY */
-
-/*
- * USB configuration
- */
-#define CONFIG_USB_UHCI		1
-#define CONFIG_USB_STORAGE	1
-#define CONFIG_USB_KEYBOARD	1
-#define CONFIG_SYS_STDIO_DEREGISTER	1 /* needed by CONFIG_USB_KEYBOARD */
-
-/*
- * Autoboot stuff
- */
-#define CONFIG_BOOTDELAY	5 /* Boot automatically after five seconds */
-#define CONFIG_PREBOOT		""
-#define CONFIG_BOOTCOMMAND	"fdcboot; diskboot"
-#define CONFIG_MENUPROMPT	\
-	"Press any key to interrupt autoboot: %2d ", bootdelay
-#define CONFIG_MENUKEY		' '
-#define CONFIG_MENUCOMMAND	"menu"
-/* #define CONFIG_AUTOBOOT_KEYED */
-
-/*
- * Extra ENV stuff
- */
-#define CONFIG_EXTRA_ENV_SETTINGS		\
-	"stdout=vga\0"				\
-	"stdin=ps2kbd\0"			\
-	"ide_doreset=on\0"			\
-	"ide_maxbus=2\0"			\
-	"ide_cd_timeout=30\0"			\
-	"menucmd=menu\0"			\
-	"pci_irqa=9\0"				\
-	"pci_irqa_select=edge\0"		\
-	"pci_irqb=10\0"				\
-	"pci_irqb_select=edge\0"		\
-	"pci_irqc=11\0"				\
-	"pci_irqc_select=edge\0"		\
-	"pci_irqd=7\0"				\
-	"pci_irqd_select=edge\0"
-
-
-/* #define CONFIG_MII		1 */
-/* #define CONFIG_BITBANGMII	1 */
-
-
-#endif	/* __CONFIG_H */
-- 
cgit v1.1


From 8d1f63554b0371d3b30e481ac0aafa8253b515df Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Date: Wed, 16 Jun 2010 07:59:17 +0900
Subject: sh: Fix build on the target

SH fails building on the target.
This supports this.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
 Makefile | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Makefile b/Makefile
index 87d5214..f46b123 100644
--- a/Makefile
+++ b/Makefile
@@ -40,7 +40,8 @@ HOSTARCH := $(shell uname -m | \
 	    -e s/sa110/arm/ \
 	    -e s/ppc64/powerpc/ \
 	    -e s/ppc/powerpc/ \
-	    -e s/macppc/powerpc/)
+	    -e s/macppc/powerpc/\
+	    -e s/sh.*/sh/)
 
 HOSTOS := $(shell uname -s | tr '[:upper:]' '[:lower:]' | \
 	    sed -e 's/\(cygwin\).*/cygwin/')
-- 
cgit v1.1


From 61973afc5912c4c22d21f0412c824cbac1d3ee3f Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Date: Wed, 16 Jun 2010 08:10:21 +0900
Subject: sh: Fix overflow problem in get_ticks

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
 arch/sh/lib/time.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/arch/sh/lib/time.c b/arch/sh/lib/time.c
index 9a8f89a..bc1656f 100644
--- a/arch/sh/lib/time.c
+++ b/arch/sh/lib/time.c
@@ -2,7 +2,7 @@
  * (C) Copyright 2009
  * Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  *
- * (C) Copyright 2007-2008
+ * (C) Copyright 2007-2010
  * Nobobuhiro Iwamatsu <iwamatsu@nigauri.org>
  *
  * (C) Copyright 2003
@@ -36,6 +36,8 @@
 #define TMU_MAX_COUNTER (~0UL)
 
 static ulong timer_freq;
+static unsigned long last_tcnt;
+static unsigned long long overflow_ticks;
 
 static inline unsigned long long tick_to_time(unsigned long long tick)
 {
@@ -97,12 +99,26 @@ int timer_init (void)
 	tmu_timer_stop(0);
 	tmu_timer_start(0);
 
+	last_tcnt = 0;
+	overflow_ticks = 0;
+
 	return 0;
 }
 
 unsigned long long get_ticks (void)
 {
-	return 0 - readl(TCNT0);
+	unsigned long tcnt = 0 - readl(TCNT0);
+	unsigned long ticks;
+
+	if (last_tcnt > tcnt) { /* overflow */
+		overflow_ticks++;
+		ticks = (0xffffffff - last_tcnt) + tcnt;
+	} else {
+		ticks = tcnt;
+	}
+	last_tcnt = tcnt;
+
+	return (overflow_ticks << 32) | tcnt;
 }
 
 void __udelay (unsigned long usec)
-- 
cgit v1.1


From 9a1e3e9fe3165130c228bc861bd96d49df708290 Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Date: Wed, 16 Jun 2010 16:53:45 +0900
Subject: sh: Fix path of irqflags.h

This changes path of irqflags.h from linux/ to asm/.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
 arch/sh/include/asm/system.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/sh/include/asm/system.h b/arch/sh/include/asm/system.h
index a62c422..90a53a0 100644
--- a/arch/sh/include/asm/system.h
+++ b/arch/sh/include/asm/system.h
@@ -8,7 +8,7 @@
  * from linux kernel code.
  */
 
-#include <linux/irqflags.h>
+#include <asm/irqflags.h>
 #include <asm/types.h>
 
 /*
-- 
cgit v1.1


From 754613f740368f847a2261c5c41b034ff5c51b1c Mon Sep 17 00:00:00 2001
From: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Date: Wed, 16 Jun 2010 16:55:26 +0900
Subject: sh: Add trigger_address_error and support cpu reset

This add support cpu reset by trigger_address_error function.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
 arch/sh/cpu/sh2/watchdog.c   |  8 ++++++--
 arch/sh/cpu/sh3/watchdog.c   |  7 +++++++
 arch/sh/cpu/sh4/watchdog.c   |  4 ++++
 arch/sh/include/asm/system.h | 10 ++++++++++
 4 files changed, 27 insertions(+), 2 deletions(-)

diff --git a/arch/sh/cpu/sh2/watchdog.c b/arch/sh/cpu/sh2/watchdog.c
index de0254b..0257d8d 100644
--- a/arch/sh/cpu/sh2/watchdog.c
+++ b/arch/sh/cpu/sh2/watchdog.c
@@ -1,6 +1,6 @@
 /*
- * Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhoro@renesas.com>
- * Copyright (C) 2008 Renesas Solutions Corp.
+ * Copyright (C) 2008,2010 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
+ * Copyright (C) 2008,2010 Renesas Solutions Corp.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
@@ -20,6 +20,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/system.h>
 
 int watchdog_init(void)
 {
@@ -28,6 +29,9 @@ int watchdog_init(void)
 
 void reset_cpu(unsigned long ignored)
 {
+	/* Address error with SR.BL=1 first. */
+	trigger_address_error();
+
 	while (1)
 		;
 }
diff --git a/arch/sh/cpu/sh3/watchdog.c b/arch/sh/cpu/sh3/watchdog.c
index 92bea74..90694f8 100644
--- a/arch/sh/cpu/sh3/watchdog.c
+++ b/arch/sh/cpu/sh3/watchdog.c
@@ -1,4 +1,7 @@
 /*
+ * (C) Copyright 2010
+ * Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
+ *
  * (C) Copyright 2007
  * Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
  *
@@ -20,6 +23,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/system.h>
 
 int watchdog_init(void)
 {
@@ -28,6 +32,9 @@ int watchdog_init(void)
 
 void reset_cpu(unsigned long ignored)
 {
+	/* Address error with SR.BL=1 first. */
+	trigger_address_error();
+
 	while (1)
 		;
 }
diff --git a/arch/sh/cpu/sh4/watchdog.c b/arch/sh/cpu/sh4/watchdog.c
index f692429..d7e1703 100644
--- a/arch/sh/cpu/sh4/watchdog.c
+++ b/arch/sh/cpu/sh4/watchdog.c
@@ -17,6 +17,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/system.h>
 #include <asm/io.h>
 
 #define WDT_BASE	WTCNT
@@ -66,6 +67,9 @@ int watchdog_disable(void)
 
 void reset_cpu(unsigned long ignored)
 {
+	/* Address error with SR.BL=1 first. */
+	trigger_address_error();
+
 	while (1)
 		;
 }
diff --git a/arch/sh/include/asm/system.h b/arch/sh/include/asm/system.h
index 90a53a0..56fd77a 100644
--- a/arch/sh/include/asm/system.h
+++ b/arch/sh/include/asm/system.h
@@ -272,4 +272,14 @@ void enable_hlt(void);
 
 #define arch_align_stack(x) (x)
 
+static inline void trigger_address_error(void)
+{
+	__asm__ __volatile__ (
+		"ldc %0, sr\n\t"
+		"mov.l @%1, %0"
+		:
+		: "r" (0x10000000), "r" (0x80000001)
+	);
+}
+
 #endif
-- 
cgit v1.1


From 178e26d75212f5aba63116585ef8f67ca6854e85 Mon Sep 17 00:00:00 2001
From: Wolfgang Denk <wd@denx.de>
Date: Sat, 26 Jun 2010 23:46:40 +0200
Subject: image.h: remove bogus ';' after function declarations

ISO C does not allow extra ';' outside of a function

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 include/image.h | 44 ++++++++++++++++++++++----------------------
 1 file changed, 22 insertions(+), 22 deletions(-)

diff --git a/include/image.h b/include/image.h
index 294eba5..366b622 100644
--- a/include/image.h
+++ b/include/image.h
@@ -362,23 +362,23 @@ static inline uint32_t image_get_header_size (void)
 	{ \
 		return uimage_to_cpu (hdr->ih_##f); \
 	}
-image_get_hdr_l (magic);	/* image_get_magic */
-image_get_hdr_l (hcrc);		/* image_get_hcrc */
-image_get_hdr_l (time);		/* image_get_time */
-image_get_hdr_l (size);		/* image_get_size */
-image_get_hdr_l (load);		/* image_get_load */
-image_get_hdr_l (ep);		/* image_get_ep */
-image_get_hdr_l (dcrc);		/* image_get_dcrc */
+image_get_hdr_l (magic)		/* image_get_magic */
+image_get_hdr_l (hcrc)		/* image_get_hcrc */
+image_get_hdr_l (time)		/* image_get_time */
+image_get_hdr_l (size)		/* image_get_size */
+image_get_hdr_l (load)		/* image_get_load */
+image_get_hdr_l (ep)		/* image_get_ep */
+image_get_hdr_l (dcrc)		/* image_get_dcrc */
 
 #define image_get_hdr_b(f) \
 	static inline uint8_t image_get_##f(const image_header_t *hdr) \
 	{ \
 		return hdr->ih_##f; \
 	}
-image_get_hdr_b (os);		/* image_get_os */
-image_get_hdr_b (arch);		/* image_get_arch */
-image_get_hdr_b (type);		/* image_get_type */
-image_get_hdr_b (comp);		/* image_get_comp */
+image_get_hdr_b (os)		/* image_get_os */
+image_get_hdr_b (arch)		/* image_get_arch */
+image_get_hdr_b (type)		/* image_get_type */
+image_get_hdr_b (comp)		/* image_get_comp */
 
 static inline char *image_get_name (const image_header_t *hdr)
 {
@@ -420,23 +420,23 @@ static inline ulong image_get_image_end (const image_header_t *hdr)
 	{ \
 		hdr->ih_##f = cpu_to_uimage (val); \
 	}
-image_set_hdr_l (magic);	/* image_set_magic */
-image_set_hdr_l (hcrc);		/* image_set_hcrc */
-image_set_hdr_l (time);		/* image_set_time */
-image_set_hdr_l (size);		/* image_set_size */
-image_set_hdr_l (load);		/* image_set_load */
-image_set_hdr_l (ep);		/* image_set_ep */
-image_set_hdr_l (dcrc);		/* image_set_dcrc */
+image_set_hdr_l (magic)		/* image_set_magic */
+image_set_hdr_l (hcrc)		/* image_set_hcrc */
+image_set_hdr_l (time)		/* image_set_time */
+image_set_hdr_l (size)		/* image_set_size */
+image_set_hdr_l (load)		/* image_set_load */
+image_set_hdr_l (ep)		/* image_set_ep */
+image_set_hdr_l (dcrc)		/* image_set_dcrc */
 
 #define image_set_hdr_b(f) \
 	static inline void image_set_##f(image_header_t *hdr, uint8_t val) \
 	{ \
 		hdr->ih_##f = val; \
 	}
-image_set_hdr_b (os);		/* image_set_os */
-image_set_hdr_b (arch);		/* image_set_arch */
-image_set_hdr_b (type);		/* image_set_type */
-image_set_hdr_b (comp);		/* image_set_comp */
+image_set_hdr_b (os)		/* image_set_os */
+image_set_hdr_b (arch)		/* image_set_arch */
+image_set_hdr_b (type)		/* image_set_type */
+image_set_hdr_b (comp)		/* image_set_comp */
 
 static inline void image_set_name (image_header_t *hdr, const char *name)
 {
-- 
cgit v1.1


From 81f8d3b021ac9e567f06b44d7eb95f1a1409428d Mon Sep 17 00:00:00 2001
From: Anton Vorontsov <avorontsov@mvista.com>
Date: Fri, 18 Jun 2010 15:08:12 +0400
Subject: hwconfig: Fix stop characters parsing for subkeys

For the following hwconfig string:

  key1:subkey1=value1,subkey2=value2;key2:value3

The subkey2 cannot be extracted correctly. The parsing code looks
for comma as a stopch, but there may be two kind of stop characters:
a comma and a semicolon.

Currently the code would return "value2;key2:value3", while just
"value2" is the correct answer.

This patch fixes the issue by making the code aware of multiple
stop characters.

For old U-Boots, the issue can be workarounded by placing a comma
before a semicolon, i.e.:

  hwconfig=key1:subkey1=value1,subkey2=value2,;key2:value3

Reported-by: York Sun <yorksun@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
---
 common/hwconfig.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/common/hwconfig.c b/common/hwconfig.c
index e5c60ba..85a69da 100644
--- a/common/hwconfig.c
+++ b/common/hwconfig.c
@@ -19,7 +19,7 @@
 #include <linux/string.h>
 
 static const char *hwconfig_parse(const char *opts, size_t maxlen,
-				  const char *opt, char stopch, char eqch,
+				  const char *opt, char *stopchs, char eqch,
 				  size_t *arglen)
 {
 	size_t optlen = strlen(opt);
@@ -33,8 +33,9 @@ next:
 	if (end - start > maxlen)
 		return NULL;
 
-	if (str && (str == opts || str[-1] == stopch) &&
-			(*end == stopch || *end == eqch || *end == '\0')) {
+	if (str && (str == opts || strpbrk(str - 1, stopchs) == str - 1) &&
+			(strpbrk(end, stopchs) == end || *end == eqch ||
+			 *end == '\0')) {
 		const char *arg_end;
 
 		if (!arglen)
@@ -43,7 +44,7 @@ next:
 		if (*end != eqch)
 			return NULL;
 
-		arg_end = strchr(str, stopch);
+		arg_end = strpbrk(str, stopchs);
 		if (!arg_end)
 			*arglen = min(maxlen, strlen(str)) - optlen - 1;
 		else
@@ -66,15 +67,15 @@ static const char *__hwconfig(const char *opt, size_t *arglen)
 
 	if (env_hwconfig)
 		return hwconfig_parse(env_hwconfig, strlen(env_hwconfig),
-				      opt, ';', ':', arglen);
+				      opt, ";", ':', arglen);
 
 	if (board_hwconfig)
 		return hwconfig_parse(board_hwconfig, strlen(board_hwconfig),
-				      opt, ';', ':', arglen);
+				      opt, ";", ':', arglen);
 
 	if (cpu_hwconfig)
 		return hwconfig_parse(cpu_hwconfig, strlen(cpu_hwconfig),
-				      opt, ';', ':', arglen);
+				      opt, ";", ':', arglen);
 
 	return NULL;
 }
@@ -164,7 +165,7 @@ int hwconfig_sub(const char *opt, const char *subopt)
 	arg = __hwconfig(opt, &arglen);
 	if (!arg)
 		return 0;
-	return !!hwconfig_parse(arg, arglen, subopt, ',', '=', NULL);
+	return !!hwconfig_parse(arg, arglen, subopt, ",;", '=', NULL);
 }
 
 /*
@@ -185,7 +186,7 @@ const char *hwconfig_subarg(const char *opt, const char *subopt,
 	arg = __hwconfig(opt, &arglen);
 	if (!arg)
 		return NULL;
-	return hwconfig_parse(arg, arglen, subopt, ',', '=', subarglen);
+	return hwconfig_parse(arg, arglen, subopt, ",;", '=', subarglen);
 }
 
 /*
-- 
cgit v1.1


From 3bf74a4183fdf32e9be2742594ed8199e626650c Mon Sep 17 00:00:00 2001
From: Anton Vorontsov <avorontsov@mvista.com>
Date: Fri, 18 Jun 2010 15:08:27 +0400
Subject: hwconfig: Add some unit tests

I use this for testing, and I think this might be useful in the
future.

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
---
 common/hwconfig.c | 55 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 55 insertions(+)

diff --git a/common/hwconfig.c b/common/hwconfig.c
index 85a69da..1f9f4a0 100644
--- a/common/hwconfig.c
+++ b/common/hwconfig.c
@@ -11,12 +11,20 @@
  * the License, or (at your option) any later version.
  */
 
+#ifndef HWCONFIG_TEST
 #include <config.h>
 #include <common.h>
 #include <exports.h>
 #include <hwconfig.h>
 #include <linux/types.h>
 #include <linux/string.h>
+#else
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <assert.h>
+#define min(a, b) (((a) < (b)) ? (a) : (b))
+#endif /* HWCONFIG_TEST */
 
 static const char *hwconfig_parse(const char *opts, size_t maxlen,
 				  const char *opt, char *stopchs, char eqch,
@@ -209,3 +217,50 @@ int hwconfig_subarg_cmp(const char *opt, const char *subopt, const char *subarg)
 
 	return !strncmp(argstr, subarg, arglen);
 }
+
+#ifdef HWCONFIG_TEST
+int main()
+{
+	const char *ret;
+	size_t len;
+
+	setenv("hwconfig", "key1:subkey1=value1,subkey2=value2;key2:value3;;;;"
+			   "key3;:,:=;key4", 1);
+
+	ret = hwconfig_arg("key1", &len);
+	printf("%zd %.*s\n", len, (int)len, ret);
+	assert(len == 29);
+	assert(hwconfig_arg_cmp("key1", "subkey1=value1,subkey2=value2"));
+	assert(!strncmp(ret, "subkey1=value1,subkey2=value2", len));
+
+	ret = hwconfig_subarg("key1", "subkey1", &len);
+	printf("%zd %.*s\n", len, (int)len, ret);
+	assert(len == 6);
+	assert(hwconfig_subarg_cmp("key1", "subkey1", "value1"));
+	assert(!strncmp(ret, "value1", len));
+
+	ret = hwconfig_subarg("key1", "subkey2", &len);
+	printf("%zd %.*s\n", len, (int)len, ret);
+	assert(len == 6);
+	assert(hwconfig_subarg_cmp("key1", "subkey2", "value2"));
+	assert(!strncmp(ret, "value2", len));
+
+	ret = hwconfig_arg("key2", &len);
+	printf("%zd %.*s\n", len, (int)len, ret);
+	assert(len == 6);
+	assert(hwconfig_arg_cmp("key2", "value3"));
+	assert(!strncmp(ret, "value3", len));
+
+	assert(hwconfig("key3"));
+	assert(hwconfig_arg("key4", &len) == NULL);
+	assert(hwconfig_arg("bogus", &len) == NULL);
+
+	unsetenv("hwconfig");
+
+	assert(hwconfig(NULL) == 0);
+	assert(hwconfig("") == 0);
+	assert(hwconfig("key3") == 0);
+
+	return 0;
+}
+#endif /* HWCONFIG_TEST */
-- 
cgit v1.1


From 620bbba524fbaa26971a5004793010b169824f1b Mon Sep 17 00:00:00 2001
From: Peter Tyser <ptyser@xes-inc.com>
Date: Tue, 15 Jun 2010 21:48:25 +0200
Subject: examples/standalone: Remove relocation compile flags for PowerPC

Previously, standalone applications were compiled with gcc flags that
produced relocatable executables on the PowerPC architecture (eg with
the -mrelocatable and -fPIC flags).  There's no reason for these
applications to be fully relocatable at this time since no relocation
fixups are performed on standalone applications.

Additionally, removing the gcc relocation flags results in the entry
point of applications residing at the base of the image.  When
a standalone application was relocatable, the entry point was generally
located at an offset into the image which was confusing and prone to
errors.

This change moves the entry point of PowerPC standalone applications
from 0x40004 (usually) to 0x40000.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 examples/standalone/Makefile | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/examples/standalone/Makefile b/examples/standalone/Makefile
index 6ea3b93..5f1f800 100644
--- a/examples/standalone/Makefile
+++ b/examples/standalone/Makefile
@@ -72,6 +72,16 @@ gcclibdir := $(shell dirname `$(CC) -print-libgcc-file-name`)
 
 CPPFLAGS += -I..
 
+# For PowerPC there's no need to compile standalone applications as a
+# relocatable executable.  The relocation data is not needed, and
+# also causes the entry point of the standalone application to be
+# inconsistent.
+ifeq ($(ARCH),powerpc)
+AFLAGS := $(filter-out $(RELFLAGS),$(AFLAGS))
+CFLAGS := $(filter-out $(RELFLAGS),$(CFLAGS))
+CPPFLAGS := $(filter-out $(RELFLAGS),$(CPPFLAGS))
+endif
+
 all:	$(obj).depend $(OBJS) $(LIB) $(SREC) $(BIN) $(ELF)
 
 #########################################################################
-- 
cgit v1.1


From d04250cbe1999cfaafee590dfb3191ade305fb63 Mon Sep 17 00:00:00 2001
From: "Reinhard Meyer (-VC)" <reinhard.meyer@emk-elektronik.de>
Date: Mon, 14 Jun 2010 12:14:00 +0200
Subject: Fix (null) problem for AVR32 boards

Currently the U-Boot address ranges for AVR32 boards are
printed like this:
"U-Boot code: (null) -> 0001183c  data: 000188e8 -> 0004e9b0"
This patch fixes this to print:
"U-Boot code: 00000000 -> 0001183c  data: 000188f8 -> 0004e9c0"

Signed-off-by: Reinhard Meyer <info@emk-elektronik.de>
---
 arch/avr32/lib/board.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/avr32/lib/board.c b/arch/avr32/lib/board.c
index 917ed6c..254aecf 100644
--- a/arch/avr32/lib/board.c
+++ b/arch/avr32/lib/board.c
@@ -115,8 +115,9 @@ static int init_baudrate(void)
 static int display_banner (void)
 {
 	printf ("\n\n%s\n\n", version_string);
-	printf ("U-Boot code: %p -> %p  data: %p -> %p\n",
-		_text, _etext, _data, _end);
+	printf ("U-Boot code: %08lx -> %08lx  data: %08lx -> %08lx\n",
+		(unsigned long)_text, (unsigned long)_etext,
+		(unsigned long)_data, (unsigned long)_end);
 	return 0;
 }
 
-- 
cgit v1.1


From c99ea790788ae83d813e2c6c03291cb5672cc6c0 Mon Sep 17 00:00:00 2001
From: Reinhard Meyer <info@emk-elektronik.de>
Date: Sun, 6 Jun 2010 19:01:59 +0200
Subject: Fix #if chain and added AVR32 case in cmd_bdinfo.c
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

AVR32 case was missing in cmd_bdinfo, resulting in compiler warning
(bd->bi_baudrate declared unsigned int at AVR32, but printf used %d)

At the same time slightly reordered #if #elif #endif to make ARM one
of the cases and not an extra case surrounding all others

Signed-off-by: Reinhard Meyer <info@emk-elektronik.de>
Tested-by: Andreas Bießmann <biessmann@corscience.de>
---
 common/cmd_bdinfo.c | 44 +++++++++++++++++++++++++++++++++++---------
 1 file changed, 35 insertions(+), 9 deletions(-)

diff --git a/common/cmd_bdinfo.c b/common/cmd_bdinfo.c
index a0f7998..710abdf 100644
--- a/common/cmd_bdinfo.c
+++ b/common/cmd_bdinfo.c
@@ -37,8 +37,9 @@ static void print_eth(int idx);
 
 #ifndef CONFIG_ARM	/* PowerPC and other */
 static void print_lnum(const char *, u64);
+#endif
 
-#ifdef CONFIG_PPC
+#if defined(CONFIG_PPC)
 static void print_str(const char *, const char *);
 
 int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
@@ -119,7 +120,7 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	return 0;
 }
 
-#elif defined(CONFIG_NIOS2) /* Nios-II */
+#elif defined(CONFIG_NIOS2)
 
 int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
@@ -145,7 +146,8 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 	return 0;
 }
-#elif defined(CONFIG_MICROBLAZE) /* ! PPC, which leaves Microblaze */
+
+#elif defined(CONFIG_MICROBLAZE)
 
 int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
@@ -167,7 +169,8 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	return 0;
 }
 
-#elif defined(CONFIG_SPARC)	/* SPARC */
+#elif defined(CONFIG_SPARC)
+
 int do_bdinfo(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
 {
 	bd_t *bd = gd->bd;
@@ -199,7 +202,8 @@ int do_bdinfo(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
 	return 0;
 }
 
-#elif defined(CONFIG_M68K) /* M68K */
+#elif defined(CONFIG_M68K)
+
 static void print_str(const char *, const char *);
 
 int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
@@ -249,6 +253,7 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 }
 
 #elif defined(CONFIG_BLACKFIN)
+
 static void print_str(const char *, const char *);
 
 int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
@@ -277,7 +282,7 @@ int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	return 0;
 }
 
-#else /* ! PPC, which leaves MIPS */
+#elif defined(CONFIG_MIPS)
 
 int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
@@ -296,9 +301,28 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 	return 0;
 }
-#endif  /* MIPS */
 
-#else	/* ARM */
+#elif defined(CONFIG_AVR32)
+
+int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	bd_t *bd = gd->bd;
+
+	print_num ("boot_params",	(ulong)bd->bi_boot_params);
+	print_num ("memstart",		(ulong)bd->bi_memstart);
+	print_lnum ("memsize",		(u64)bd->bi_memsize);
+	print_num ("flashstart",	(ulong)bd->bi_flashstart);
+	print_num ("flashsize",		(ulong)bd->bi_flashsize);
+	print_num ("flashoffset",	(ulong)bd->bi_flashoffset);
+
+	print_eth(0);
+	printf ("ip_addr     = %pI4\n", &bd->bi_ip_addr);
+	printf ("baudrate    = %lu bps\n", bd->bi_baudrate);
+
+	return 0;
+}
+
+#elif defined(CONFIG_ARM)
 
 int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
@@ -324,7 +348,9 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	return 0;
 }
 
-#endif /* CONFIG_ARM XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX */
+#else
+ #error "a case for this architecture does not exist!"
+#endif
 
 static void print_num(const char *name, ulong value)
 {
-- 
cgit v1.1


From eb70d05d740c1d82474d2c31242a4e995584de24 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Andreas=20Bie=C3=9Fmann?= <biessmann@corscience.de>
Date: Wed, 9 Jun 2010 14:13:45 +0200
Subject: avr32: disable branch folding
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Due to a hardware bug mentioned in latest AP7000 datasheet errata
(revision M from 09.09) branch folding is unreliable.
This patch disables CPUCR.FE bitfield as stated in datasheet.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
---
 arch/avr32/cpu/start.S | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/arch/avr32/cpu/start.S b/arch/avr32/cpu/start.S
index d37a46e..99c9e06 100644
--- a/arch/avr32/cpu/start.S
+++ b/arch/avr32/cpu/start.S
@@ -27,9 +27,10 @@
 #define SYSREG_MMUCR_S_OFFSET	4
 
 #define SR_INIT (SYSREG_BIT(GM) | SYSREG_BIT(EM) | SYSREG_BIT(M0))
-#define CPUCR_INIT (SYSREG_BIT(BI) | SYSREG_BIT(BE)		\
-		    | SYSREG_BIT(FE) | SYSREG_BIT(RE)		\
-		    | SYSREG_BIT(IBE) | SYSREG_BIT(IEE))
+/* due to errata (unreliable branch folding) clear FE bit explicitly */
+#define CPUCR_INIT ((SYSREG_BIT(BI) | SYSREG_BIT(BE)	\
+		    | SYSREG_BIT(RE)   |  SYSREG_BIT(IBE)		\
+		    | SYSREG_BIT(IEE)) & ~SYSREG_BIT(FE))
 
 	/*
 	 * To save some space, we use the same entry point for
-- 
cgit v1.1


From 418cbb0abc8aa28a130366bd9d982cc4afd478c7 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Andreas=20Bie=C3=9Fmann?= <biessmann@corscience.de>
Date: Wed, 9 Jun 2010 10:27:32 +0200
Subject: avr32: fix linking of atstk100x and favr32 boards
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

When building some avr32 boards out of tree (e.g. O=..) the linker script could
not be found. This patch references the linker script in source tree.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
---
 board/atmel/atstk1000/config.mk        | 2 +-
 board/earthlcd/favr-32-ezkit/config.mk | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/board/atmel/atstk1000/config.mk b/board/atmel/atstk1000/config.mk
index ec3618d..40e55fe 100644
--- a/board/atmel/atstk1000/config.mk
+++ b/board/atmel/atstk1000/config.mk
@@ -1,4 +1,4 @@
 PLATFORM_RELFLAGS	+= -ffunction-sections -fdata-sections
 PLATFORM_LDFLAGS	+= --gc-sections
 TEXT_BASE		= 0x00000000
-LDSCRIPT		= $(obj)board/atmel/atstk1000/u-boot.lds
+LDSCRIPT		= $(src)board/atmel/atstk1000/u-boot.lds
diff --git a/board/earthlcd/favr-32-ezkit/config.mk b/board/earthlcd/favr-32-ezkit/config.mk
index 2337d62..5c919cd 100644
--- a/board/earthlcd/favr-32-ezkit/config.mk
+++ b/board/earthlcd/favr-32-ezkit/config.mk
@@ -1,4 +1,4 @@
 PLATFORM_RELFLAGS	+= -ffunction-sections -fdata-sections
 PLATFORM_LDFLAGS	+= --gc-sections
 TEXT_BASE		= 0x00000000
-LDSCRIPT		= $(obj)board/earthlcd/favr-32-ezkit/u-boot.lds
+LDSCRIPT		= $(src)board/earthlcd/favr-32-ezkit/u-boot.lds
-- 
cgit v1.1


From 3746a5e65ceeccf7e766df6263d2994b9abcc60e Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Andreas=20Bie=C3=9Fmann?= <biessmann@corscience.de>
Date: Wed, 9 Jun 2010 10:29:00 +0200
Subject: avr32: add unaligned.h
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

This patch fixes following error:

zlib.c:31:27: error: asm/unaligned.h: No such file or directory

Suggested-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
---
 arch/avr32/include/asm/unaligned.h | 1 +
 1 file changed, 1 insertion(+)
 create mode 100644 arch/avr32/include/asm/unaligned.h

diff --git a/arch/avr32/include/asm/unaligned.h b/arch/avr32/include/asm/unaligned.h
new file mode 100644
index 0000000..6cecbbb
--- /dev/null
+++ b/arch/avr32/include/asm/unaligned.h
@@ -0,0 +1 @@
+#include <asm-generic/unaligned.h>
-- 
cgit v1.1


From bd7b26f879413aa5a662718c09dab65d3a24a201 Mon Sep 17 00:00:00 2001
From: Stefano Babic <sbabic@denx.de>
Date: Mon, 24 May 2010 12:08:16 +0200
Subject: Tools: set multiple variable with fw_setenv utility

Add a sort of batch mode to fw_setenv, allowing to set
multiple variables in one shot, without updating the flash after
each set as now. It is added the possibility to pass
a config file with a list of pairs <variable, value> to be set,
separated by a TAB character.

Signed-off-by: Stefano Babic <sbabic@denx.de>
---
 tools/env/fw_env.c      | 269 ++++++++++++++++++++++++++++++++++++++++--------
 tools/env/fw_env.h      |   4 +
 tools/env/fw_env_main.c |  67 ++++++++++--
 3 files changed, 288 insertions(+), 52 deletions(-)

diff --git a/tools/env/fw_env.c b/tools/env/fw_env.c
index a46205d..04f3bf0 100644
--- a/tools/env/fw_env.c
+++ b/tools/env/fw_env.c
@@ -45,8 +45,7 @@
 
 #include "fw_env.h"
 
-#define	CMD_GETENV	"fw_printenv"
-#define	CMD_SETENV	"fw_setenv"
+#define WHITESPACE(c) ((c == '\t') || (c == ' '))
 
 #define min(x, y) ({				\
 	typeof(x) _min1 = (x);			\
@@ -210,7 +209,6 @@ static char default_environment[] = {
 
 static int flash_io (int mode);
 static char *envmatch (char * s1, char * s2);
-static int env_init (void);
 static int parse_config (void);
 
 #if defined(CONFIG_FILE)
@@ -225,6 +223,22 @@ static inline ulong getenvsize (void)
 	return rc;
 }
 
+static char *fw_string_blank(char *s, int noblank)
+{
+	int i;
+	int len = strlen(s);
+
+	for (i = 0; i < len; i++, s++) {
+		if ((noblank && !WHITESPACE(*s)) ||
+			(!noblank && WHITESPACE(*s)))
+			break;
+	}
+	if (i == len)
+		return NULL;
+
+	return s;
+}
+
 /*
  * Search the environment for a variable.
  * Return the value, if found, or NULL, if not found.
@@ -233,7 +247,7 @@ char *fw_getenv (char *name)
 {
 	char *env, *nxt;
 
-	if (env_init ())
+	if (fw_env_open())
 		return NULL;
 
 	for (env = environment.data; *env; env = nxt + 1) {
@@ -264,7 +278,7 @@ int fw_printenv (int argc, char *argv[])
 	int i, n_flag;
 	int rc = 0;
 
-	if (env_init ())
+	if (fw_env_open())
 		return -1;
 
 	if (argc == 1) {		/* Print all env variables  */
@@ -327,30 +341,34 @@ int fw_printenv (int argc, char *argv[])
 	return rc;
 }
 
-/*
- * Deletes or sets environment variables. Returns -1 and sets errno error codes:
- * 0	  - OK
- * EINVAL - need at least 1 argument
- * EROFS  - certain variables ("ethaddr", "serial#") cannot be
- *	    modified or deleted
- *
- */
-int fw_setenv (int argc, char *argv[])
+int fw_env_close(void)
 {
-	int i, len;
-	char *env, *nxt;
-	char *oldval = NULL;
-	char *name;
+	/*
+	 * Update CRC
+	 */
+	*environment.crc = crc32(0, (uint8_t *) environment.data, ENV_SIZE);
 
-	if (argc < 2) {
-		errno = EINVAL;
-		return -1;
+	/* write environment back to flash */
+	if (flash_io(O_RDWR)) {
+		fprintf(stderr,
+			"Error: can't write fw_env to flash\n");
+			return -1;
 	}
 
-	if (env_init ())
-		return -1;
+	return 0;
+}
 
-	name = argv[1];
+
+/*
+ * Set/Clear a single variable in the environment.
+ * This is called in sequence to update the environment
+ * in RAM without updating the copy in flash after each set
+ */
+int fw_env_write(char *name, char *value)
+{
+	int len;
+	char *env, *nxt;
+	char *oldval = NULL;
 
 	/*
 	 * search if variable with this name already exists
@@ -358,7 +376,7 @@ int fw_setenv (int argc, char *argv[])
 	for (nxt = env = environment.data; *env; env = nxt + 1) {
 		for (nxt = env; *nxt; ++nxt) {
 			if (nxt >= &environment.data[ENV_SIZE]) {
-				fprintf (stderr, "## Error: "
+				fprintf(stderr, "## Error: "
 					"environment not terminated\n");
 				errno = EINVAL;
 				return -1;
@@ -396,8 +414,8 @@ int fw_setenv (int argc, char *argv[])
 	}
 
 	/* Delete only ? */
-	if (argc < 3)
-		goto WRITE_FLASH;
+	if (!value || !strlen(value))
+		return 0;
 
 	/*
 	 * Append new definition at the end
@@ -411,41 +429,202 @@ int fw_setenv (int argc, char *argv[])
 	 */
 	len = strlen (name) + 2;
 	/* add '=' for first arg, ' ' for all others */
-	for (i = 2; i < argc; ++i) {
-		len += strlen (argv[i]) + 1;
-	}
+	len += strlen(value) + 1;
+
 	if (len > (&environment.data[ENV_SIZE] - env)) {
 		fprintf (stderr,
 			"Error: environment overflow, \"%s\" deleted\n",
 			name);
 		return -1;
 	}
+
 	while ((*env = *name++) != '\0')
 		env++;
+	*env = '=';
+	while ((*++env = *value++) != '\0')
+		;
+
+	/* end is marked with double '\0' */
+	*++env = '\0';
+
+	return 0;
+}
+
+/*
+ * Deletes or sets environment variables. Returns -1 and sets errno error codes:
+ * 0	  - OK
+ * EINVAL - need at least 1 argument
+ * EROFS  - certain variables ("ethaddr", "serial#") cannot be
+ *	    modified or deleted
+ *
+ */
+int fw_setenv(int argc, char *argv[])
+{
+	int i, len;
+	char *name;
+	char *value = NULL;
+	char *tmpval = NULL;
+
+	if (argc < 2) {
+		errno = EINVAL;
+		return -1;
+	}
+
+	if (fw_env_open()) {
+		fprintf(stderr, "Error: environment not initialized\n");
+		return -1;
+	}
+
+	name = argv[1];
+
+	len = strlen(name) + 2;
+	for (i = 2; i < argc; ++i)
+		len += strlen(argv[i]) + 1;
+
+	/* Allocate enough place to the data string */
 	for (i = 2; i < argc; ++i) {
 		char *val = argv[i];
-
-		*env = (i == 2) ? '=' : ' ';
-		while ((*++env = *val++) != '\0');
+		if (!value) {
+			value = (char *)malloc(len - strlen(name));
+			if (!value) {
+				fprintf(stderr,
+				"Cannot malloc %u bytes: %s\n",
+				len - strlen(name), strerror(errno));
+				return -1;
+			}
+			memset(value, 0, len - strlen(name));
+			tmpval = value;
+		}
+		if (i != 2)
+			*tmpval++ = ' ';
+		while (*val != '\0')
+			*tmpval++ = *val++;
 	}
 
-	/* end is marked with double '\0' */
-	*++env = '\0';
+	fw_env_write(name, value);
 
-  WRITE_FLASH:
+	if (value)
+		free(value);
 
-	/*
-	 * Update CRC
-	 */
-	*environment.crc = crc32 (0, (uint8_t *) environment.data, ENV_SIZE);
+	return fw_env_close();
+}
 
-	/* write environment back to flash */
-	if (flash_io (O_RDWR)) {
-		fprintf (stderr, "Error: can't write fw_env to flash\n");
+/*
+ * Parse  a file  and configure the u-boot variables.
+ * The script file has a very simple format, as follows:
+ *
+ * Each line has a couple with name, value:
+ * <white spaces>variable_name<white spaces>variable_value
+ *
+ * Both variable_name and variable_value are interpreted as strings.
+ * Any character after <white spaces> and before ending \r\n is interpreted
+ * as variable's value (no comment allowed on these lines !)
+ *
+ * Comments are allowed if the first character in the line is #
+ *
+ * Returns -1 and sets errno error codes:
+ * 0	  - OK
+ * -1     - Error
+ */
+int fw_parse_script(char *fname)
+{
+	FILE *fp;
+	char dump[1024];	/* Maximum line length in the file */
+	char *name;
+	char *val;
+	int lineno = 0;
+	int len;
+	int ret = 0;
+
+	if (fw_env_open()) {
+		fprintf(stderr, "Error: environment not initialized\n");
 		return -1;
 	}
 
-	return 0;
+	if (strcmp(fname, "-") == 0)
+		fp = stdin;
+	else {
+		fp = fopen(fname, "r");
+		if (fp == NULL) {
+			fprintf(stderr, "I cannot open %s for reading\n",
+				 fname);
+			return -1;
+		}
+	}
+
+	while (fgets(dump, sizeof(dump), fp)) {
+		lineno++;
+		len = strlen(dump);
+
+		/*
+		 * Read a whole line from the file. If the line is too long
+		 * or is not terminated, reports an error and exit.
+		 */
+		if (dump[len - 1] != '\n') {
+			fprintf(stderr,
+			"Line %d not corrected terminated or too long\n",
+				lineno);
+			ret = -1;
+			break;
+		}
+
+		/* Drop ending line feed / carriage return */
+		while (len > 0 && (dump[len - 1] == '\n' ||
+				dump[len - 1] == '\r')) {
+			dump[len - 1] = '\0';
+			len--;
+		}
+
+		/* Skip comment or empty lines */
+		if ((len == 0) || dump[0] == '#')
+			continue;
+
+		/*
+		 * Search for variable's name,
+		 * remove leading whitespaces
+		 */
+		name = fw_string_blank(dump, 1);
+		if (!name)
+			continue;
+
+		/* The first white space is the end of variable name */
+		val = fw_string_blank(name, 0);
+		len = strlen(name);
+		if (val) {
+			*val++ = '\0';
+			if ((val - name) < len)
+				val = fw_string_blank(val, 1);
+			else
+				val = NULL;
+		}
+
+#ifdef DEBUG
+		fprintf(stderr, "Setting %s : %s\n",
+			name, val ? val : " removed");
+#endif
+
+		/*
+		 * If there is an error setting a variable,
+		 * try to save the environment and returns an error
+		 */
+		if (fw_env_write(name, val)) {
+			fprintf(stderr,
+			"fw_env_write returns with error : %s\n",
+				strerror(errno));
+			ret = -1;
+			break;
+		}
+
+	}
+
+	/* Close file if not stdin */
+	if (strcmp(fname, "-") != 0)
+		fclose(fp);
+
+	ret |= fw_env_close();
+
+	return ret;
+
 }
 
 /*
@@ -880,7 +1059,7 @@ static char *envmatch (char * s1, char * s2)
 /*
  * Prevent confusion if running from erased flash memory
  */
-static int env_init (void)
+int fw_env_open(void)
 {
 	int crc0, crc0_ok;
 	char flag0;
diff --git a/tools/env/fw_env.h b/tools/env/fw_env.h
index c04da54..8130fa1 100644
--- a/tools/env/fw_env.h
+++ b/tools/env/fw_env.h
@@ -50,5 +50,9 @@
 extern int   fw_printenv(int argc, char *argv[]);
 extern char *fw_getenv  (char *name);
 extern int fw_setenv  (int argc, char *argv[]);
+extern int fw_parse_script(char *fname);
+extern int fw_env_open(void);
+extern int fw_env_write(char *name, char *value);
+extern int fw_env_close(void);
 
 extern unsigned	long  crc32	 (unsigned long, const unsigned char *, unsigned);
diff --git a/tools/env/fw_env_main.c b/tools/env/fw_env_main.c
index 7f631c4..82116b4 100644
--- a/tools/env/fw_env_main.c
+++ b/tools/env/fw_env_main.c
@@ -42,34 +42,87 @@
 #include <stdio.h>
 #include <string.h>
 #include <stdlib.h>
+#include <getopt.h>
 #include "fw_env.h"
 
 #define	CMD_PRINTENV	"fw_printenv"
 #define CMD_SETENV	"fw_setenv"
 
+static struct option long_options[] = {
+	{"script", required_argument, NULL, 's'},
+	{"help", no_argument, NULL, 'h'},
+	{NULL, 0, NULL, 0}
+};
+
+void usage(void)
+{
+
+	fprintf(stderr, "fw_printenv/fw_setenv, "
+		"a command line interface to U-Boot environment\n\n"
+		"usage:\tfw_printenv\n"
+		"\tfw_setenv [variable name] [variable value]\n"
+		"\tfw_setenv -s [ file ]\n"
+		"\tfw_setenv -s - < [ file ]\n\n"
+		"The file passed as argument contains only pairs "
+		"name / value\n"
+		"Example:\n"
+		"# Any line starting with # is treated as comment\n"
+		"\n"
+		"\t      netdev         eth0\n"
+		"\t      kernel_addr    400000\n"
+		"\t      var1\n"
+		"\t      var2          The quick brown fox jumps over the "
+		"lazy dog\n"
+		"\n"
+		"A variable without value will be dropped. It is possible\n"
+		"to put any number of spaces between the fields, but any\n"
+		"space inside the value is treated as part of the value "
+		"itself.\n\n"
+	);
+}
+
 int
 main(int argc, char *argv[])
 {
 	char *p;
 	char *cmdname = *argv;
+	char *script_file = NULL;
+	int c;
 
 	if ((p = strrchr (cmdname, '/')) != NULL) {
 		cmdname = p + 1;
 	}
 
+	while ((c = getopt_long (argc, argv, "s:h",
+		long_options, NULL)) != EOF) {
+		switch (c) {
+		case 's':
+			script_file = optarg;
+			break;
+		case 'h':
+			usage();
+			return EXIT_SUCCESS;
+		}
+	}
+
+
 	if (strcmp(cmdname, CMD_PRINTENV) == 0) {
 
 		if (fw_printenv (argc, argv) != 0)
-			return (EXIT_FAILURE);
+			return EXIT_FAILURE;
 
-		return (EXIT_SUCCESS);
+		return EXIT_SUCCESS;
 
 	} else if (strcmp(cmdname, CMD_SETENV) == 0) {
+		if (!script_file) {
+			if (fw_setenv(argc, argv) != 0)
+				return EXIT_FAILURE;
+		} else {
+			if (fw_parse_script(script_file) != 0)
+				return EXIT_FAILURE;
+		}
 
-		if (fw_setenv (argc, argv) != 0)
-			return (EXIT_FAILURE);
-
-		return (EXIT_SUCCESS);
+		return EXIT_SUCCESS;
 
 	}
 
@@ -77,5 +130,5 @@ main(int argc, char *argv[])
 		"Identity crisis - may be called as `" CMD_PRINTENV
 		"' or as `" CMD_SETENV "' but not as `%s'\n",
 		cmdname);
-	return (EXIT_FAILURE);
+	return EXIT_FAILURE;
 }
-- 
cgit v1.1


From 955ea6fc2749a4305395758fc797cf8c11dcbed7 Mon Sep 17 00:00:00 2001
From: Michael Weiss <michael.weiss@ifm.com>
Date: Thu, 20 May 2010 16:09:34 +0200
Subject: powerpc/bootcount: Add bootcount support for MPC512x

This also uses the breadcrumb register as on MPC5200.

Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
---
 arch/powerpc/lib/bootcount.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/powerpc/lib/bootcount.c b/arch/powerpc/lib/bootcount.c
index 338c848..07ef28d 100644
--- a/arch/powerpc/lib/bootcount.c
+++ b/arch/powerpc/lib/bootcount.c
@@ -35,6 +35,11 @@
 #define CONFIG_SYS_BOOTCOUNT_SINGLEWORD
 #endif /* defined(CONFIG_MPC5xxx) */
 
+#if defined(CONFIG_MPC512X)
+#define CONFIG_SYS_BOOTCOUNT_ADDR	(&((immap_t *)CONFIG_SYS_IMMR)->clk.bcr)
+#define CONFIG_SYS_BOOTCOUNT_SINGLEWORD
+#endif /* defined(CONFIG_MPC512X) */
+
 #if defined(CONFIG_8xx)
 #define CONFIG_SYS_BOOTCOUNT_ADDR (((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_dpmem + \
 				CPM_BOOTCOUNT_ADDR)
-- 
cgit v1.1