summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
...
| * | | ide: add configurationAlbert Aribaud2010-08-08-0/+4
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_IDE_SWAP_IO This configuration option replaces a complex conditional in cmd_ide.c with an explicit define to be added to SoC or board configs. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
* | | Merge branch 'master' of git://git.denx.de/u-boot-tiWolfgang Denk2010-08-10-4/+139
|\ \ \
| * | | ARMV7: Update default environment for OMAP4 boardsSteve Sakoman2010-08-05-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specify vram on command line, remove erroneous call to nandboot in the boot script, add CONFIG_BOOTDELAY Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Nishanth Menon <menon.nishanth@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Enable musb driver and usbtty on OMAP4 PandaSteve Sakoman2010-08-05-0/+15
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Enable musb driver and usbtty on OMAP4430 SDPSteve Sakoman2010-08-05-0/+15
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Add support for the TWL6030 I2C power chip used in OMAP4 systemsSteve Sakoman2010-08-05-0/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add the basic infrastructure for the TWL6030 driver and enables support in the two existing OMAP4 boards, Panda and OMAP4430 SDP Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Fix udelay for OMAP4Steve Sakoman2010-08-05-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The OMAP4 x-load code sets gptimer1 clock source to 32Khz. This isn't acceptable for udelay. This patch changes from gptimer1 to gptimer2, which uses sys_clk at 38.4 Mhz. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | ARMV7: Add pad mux support for OMAP4Steve Sakoman2010-08-05-0/+2
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | Add functional multiplexing support for OMAP4 pads. Configure all the pads for the OMAP4430 SDP and OMAP4 Panda boards Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | | Merge branch 'master' of ../masterWolfgang Denk2010-08-10-108/+131
|\ \ \ | | |/ | |/|
| * | PXA: Declare __io for vpac270 IDEMarek Vasut2010-08-09-0/+2
| | | | | | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
| * | 8xx, kup4k/kup4x: add FDT supportHeiko Schocher2010-08-09-0/+4
| | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>
| * | 8xx, kup4k/kup4x: configuration changes, code cleanupHeiko Schocher2010-08-09-108/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - nfs-options removed - hda->sda changed - mtd parts added - loadaddress changed - cmd-line length increased - lcd stuff removed - code cleanup (use I/O accessors etc.) Signed-off-by: Klaus Heydeck <heydeck@kieback-peter.de>
* | | Merge branch 'master' of /home/wd/git/u-boot/masterWolfgang Denk2010-08-07-187/+769
|\ \ \ | |/ / | | / | |/ |/|
| * Rename getenv_r() into getenv_f()Wolfgang Denk2010-08-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While running from flash, i. e. before relocation, we have only a limited C runtime environment without writable data segment. In this phase, some configurations (for example with environment in EEPROM) must not use the normal getenv(), but a special function. This function had been called getenv_r(), with the idea that the "_r" suffix would mean the same as in the _r_eentrant versions of some of the C library functions (for example getdate vs. getdate_r, getgrent vs. getgrent_r, etc.). Unfortunately this was a misleading name, as in U-Boot the "_r" generally means "running from RAM", i. e. _after_ relocation. To avoid confusion, rename into getenv_f() [as "running from flash"] Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
| * Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2010-08-04-11/+757
| |\
| | * powerpc/85xx: configure autocompletion supportKim Phillips2010-08-01-11/+30
| | | | | | | | | | | | | | | | | | | | | because it's convenient. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| | * powerpc/p4080: Add support for the P4080DS boardKumar Gala2010-08-01-0/+692
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the P4080DS board, with the following features: * 36-bit only * Boots from NOR flash * FMAN drivers NOT supported * SPD DDR initialization Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com> Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| | * powerpc/p2020ds: Integrated with P2020DS DDR change and enabled hwconfigyork2010-07-26-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | Enabled SPD Enabled DDR2 Enabled hwconfig Signed-off-by: York Sun <yorksun@freescale.com>
| | * powerpc/8xxx: Enable DDR3 RDIMM supportyork2010-07-26-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | Enabled registered DIMMs using data from SPD. RDIMMs have registers which need to be configured before using. The register configuration words are stored in SPD byte 60~116 (JEDEC standard No.21-C). Software should read those RCWs and put into DDR controller before initialization. Signed-off-by: York Sun <yorksun@freescale.com>
| | * powerpc/8xxx: Fix bug in memctrl interleaving & bank interleaving on cs0~cs4york2010-07-26-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual rank with 512MB each rank. Also check dimm size and rank size for memory controller interleaving Signed-off-by: York Sun <yorksun@freescale.com>
| | * fdt: Add function to alloc phandle valuesKumar Gala2010-07-26-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If we are creating reference (handles) to nodes in a device tree we need to first create a new phandle in node and this needs a new phandle value. So we search through the whole dtb to find the max phandle value and return the next greater value for a new phandle allocation. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
| | * powerpc/p2020: Move INIT_RAM_ADDR physical address higher for 36-bit for P2020DSyork2010-07-26-0/+12
| | | | | | | | | | | | | | | | | | | | | If 36-bit is enabled, move INIT_RAM_ADDR physical address higher to free lowest 4GB address space. Signed-off-by: York Sun <yorksun@freescale.com>
| * | Blackfin: bf533/bf561 boards: convert to new soft gpio i2c codeMike Frysinger2010-07-25-175/+11
| |/ | | | | | | | | | | | | | | Use the new common gpio framework to simplify and unify the soft i2c configuration settings. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Heiko Schocher <hs@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-samsungWolfgang Denk2010-08-04-0/+6
|\ \ | |/ |/|
| * s5p_goni: enable mmc0Minkyu Kang2010-08-03-0/+6
| | | | | | | | | | | | | | | | Adds the board_mmc_init function and enable the mmc command Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* | fs/fat: Big code cleanup.Wolfgang Denk2010-07-24-34/+29
| | | | | | | | | | | | | | | | - reformat - throw out macros like FAT_DPRINT and FAT_DPRINT - remove dead code Signed-off-by: Wolfgang Denk <wd@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2010-07-24-14/+23
|\ \
| * | ppc4xx: Enable "ecctest" command on t3corpStefan Roese2010-07-23-0/+1
| | | | | | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
| * | ppc4xx: Enable "ecctest" command on katmaiStefan Roese2010-07-23-0/+1
| | | | | | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
| * | ppc4xx: T3CORP fixes and updatesStefan Roese2010-07-23-14/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes some problems for the T3CORP board. Here the list of the changes: - Add 600-67 and 677 CPU frequency setting to chip_config command - Define CONFIG_DDR_RFDC_FIXED on t3corp: While using the "normal" auto calibration code, sometimes values for RFDC were picked (>= T3) that resulted in a non-working U-Boot (hang upon relocation, while running from SDRAM). With this optimized RFDC value we can force this register and use the auto-calibration code to setup the remaining calibration registers. - Increase sizes of FPGA chips selects - EBC timing updated OEN=3 for 66 MHz EBC speed - Change ext. IRQ2 setup to level-low active - Enable CONFIG_SYS_CFI_FLASH_STATUS_POLL By defining CONFIG_SYS_CFI_FLASH_STATUS_POLL, DQ7 is polled to detect the chip busy status. This is now used instead of the data toggle method which is used historically by default in the common CFI driver. With this change a problem with not written data is solved on this board, where a 32 byte block of data is still erased instead of filled with the correct content after these commands: => erase 0xfc100000 +0x1000000 .................................................................... done Erased 128 sectors => cp.b 0x100000 0xfc100000 0x1000000 Copy to Flash... done => cmp.b 0x100000 0xfc100000 0x1000000 byte at 0x00d0d6c0 (0x00) != byte at 0xfcd0d6c0 (0xff) Total of 12637888 bytes were the same Signed-off-by: Stefan Roese <sr@denx.de>
| * | ppc4xx/Canyonlands added USB board callbacksRupjyoti Sarmah2010-07-23-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Functions added to support board callbacks for USB init. This isolates USB manipulations such that it is only touched if USB is used by U-Boot. Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com> Signed-off-by: Rupjyoti Sarmah <rsarmah@appliedmicro.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | | powerpc/85xx: Rework P1022 SERDES is_serdes_configured supportKumar Gala2010-07-21-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move serdes init until after we are in ram so we can keep track of a global static protocal map for the particular serdes config we are in. This makes is_serdes_configured() much simplier and not constantly reading registers to determine if a given device is enabled based on the protocol. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | powerpc/85xx: Rework MPC8536 SERDES is_serdes_configured supportKumar Gala2010-07-21-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move serdes init until after we are in ram so we can keep track of a global static protocal map for the particular serdes config we are in. This makes is_serdes_configured() much simplier and not constantly reading registers to determine if a given device is enabled based on the protocol. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | fdt: Add fdt_node_offset_by_compat_reg helperKumar Gala2010-07-20-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Given a compatible string and physical address try and find a node that matches. This is useful when we want to find a specific device node to update (for example if we have multiple PCI nodes we can use the physical address to distinguish them when trying to update the device tree). Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
* | | fdt: Add fdt_translate_address to convert reg node to cpu phys addrKumar Gala2010-07-20-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This code is extracted out of the Linux Kernel code from arch/powerpc/kernel/prom_parse.c. We maintain some of the same structure to support multiple bus types even though we only have one in the current code. In the future we might want to translate across a PCI bus and thus it will be easier to add that functionality back in. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
* | | powerpc/86xx: Rename PCI1/2 to PCIE1/2 on MPC8641HPCN & SBC8641Kumar Gala2010-07-20-66/+64
| | | | | | | | | | | | | | | | | | | | | | | | The MPC8641 boards actually only have PCIE not PCI. Rename so we are uniform with regards to names so we can replace this code with templated code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | powerpc/86xx: Move PCI/PCIe address defines into common immap_86xx.hKumar Gala2010-07-20-12/+0
| | | | | | | | | | | | | | | | | | | | | | | | Remove dupliacted setting of PCI/PCIe address and offsets in board config.h. Renamed CONFIG_SYS_PCI1/2_ADDR to CONFIG_SYS_PCI1/2ADDR on MPC8641 boards since its really PCIE controllers and not PCI. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | powerpc/85xx: Move PCI/PCIe address defines into common immap_85xx.hKumar Gala2010-07-20-49/+0
|/ / | | | | | | | | | | | | Remove dupliacted setting of PCI/PCIe address and offsets in board config.h. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk2010-07-17-1/+1
|\ \
| * | video: cleanup comments in cfb_console.c and video_fb.hAnatolij Gustschin2010-07-17-1/+1
| | | | | | | | | | | | Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | | Drop support for GTH boardWolfgang Denk2010-07-17-421/+0
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | The board maintainer states: The GTH board is obsolete and has not been manufactured for several years. To my knowledge, no recent U-Boot build has been tested on that card. So drop support for this board. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Thomas Lange <thomas@corelatus.se> Acked-by: Thomas Lange<thomas@corelatus.se>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2010-07-16-32/+518
|\ \
| * | ppc/85xx: Convert MPC8536DS to using board common ICS307 codeKumar Gala2010-07-16-9/+5
| | | | | | | | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | ppc/85xx: Convert MPC8572DS to using board common ICS307 codeKumar Gala2010-07-16-9/+5
| | | | | | | | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Add command to report errata workaroundsKumar Gala2010-07-16-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add 'errata' command to report what errata we workaround. Report workaround for erratum SATA-A001 on P1022/P1013. Also sorted the CONFIG_CMD_* list. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc: add support for the Freescale P1022DS reference boardTimur Tabi2010-07-16-0/+470
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifics: 1) 36-bit only 2) Booting from NOR flash only 3) Environment stored in NOR flash only 4) No SPI support 5) No DIU support Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | 85xx/p1_p2_rdb: PCIe E1000 card support added.Poonam Aggrwal2010-07-16-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Enables the Intel Pro/1000 PT Gb Ethernet PCI-E Network Adapter configuration support for P1/P2 RDB. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | mpc85xx: Add reginfo commandBecky Bruce2010-07-16-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | The new command dumps the TLBCAM, the LAWs, and the BR/OR regs. Add CONFIG_CMD_REGINFO to the config for all MPC85xx parts. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | 83xx/85xx/86xx: LBC register cleanupBecky Bruce2010-07-16-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, 83xx, 86xx, and 85xx have a lot of duplicated code dedicated to defining and manipulating the LBC registers. Merge this into a single spot. To do this, we have to decide on a common name for the data structure that holds the lbc registers - it will now be known as fsl_lbc_t, and we adopt a common name for the immap layouts that include the lbc - this was previously known as either im_lbc or lbus; use the former. In addition, create accessors for the BR/OR regs that use in/out_be32 and use those instead of the mismash of access methods currently in play. I have done a successful ppc build all and tested a board or two from each processor family. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc: Update configs to properly set FSL_ELBCBecky Bruce2010-07-16-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some parts that have an Enhanced Local Bus Controller weren't setting CONFIG_FSL_ELBC. Fix this so we can use this define properly going forward (currently it's only used if PHYS_64BIT is set, which meant not all platforms needed to have it set correctly). Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-09 14:08:31 +0000