summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* ARM64: zynqmp: Correct the sdhci minimum frequency for ep108Siva Durga Prasad Paladugu2016-11-15-1/+1
| | | | | | | | Correct the sdhci minimum frequency for ep platform. It should be right shift instead of left shift operand. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Adjust to new SMC interface to get silicon versionSoren Brinkmann2016-11-15-0/+6
| | | | | | | | | | The new FW interface returns the IDCODE and version register, leaving extracting bitfields to the caller. Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynq: Add support for Zynq 7000S 7007s/7012s/7014s devicesMichal Simek2016-11-15-0/+18
| | | | | | | Zynq 7000S (Single A9 core) devices is using different ID code. This patch adds this new codes and assign them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: nand: Enable Nand flash controller driver a zynq boardSiva Durga Prasad Paladugu2016-11-15-0/+7
| | | | | | | | Enable zynq Nand flash controller driver for a zynq ZC770 XM011(dc2) board. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynq: Add support for the topic-miami system-on-modules and carrier boardsMike Looijmans2016-11-15-0/+151
| | | | | | | | | | | | | | The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM, 32MB QSPI NOR flash and 256MB NAND flash. The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC, 2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources and a fan controller. The "Florida" carrier boards add SD, USB, ethernet and other interfaces. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* net: phy: micrel: center FLP burst timing at 16msAsh Charles2016-11-07-0/+3
| | | | | | | | | | | | | Like [1], reset the FLP burst timing for the KSZ9031 to the 16ms specified by the IEEE802.3 standard from the chip's default of 8ms. For more details, see the "Auto-Negotiation Timing" section of the KSZ9031RNX datasheet. [1] https://patchwork.kernel.org/patch/6558371/ Signed-off-by: Ash Charles <ash.charles@savoirfairelinux.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* colibri_pxa270: drop lzma support for space reasonMarcel Ziswiler2016-11-05-1/+0
| | | | | | | As the upcoming driver model integration takes up some more precious flash space first make sure to drop expensive LZMA support. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
* Merge git://git.denx.de/u-boot-rockchipTom Rini2016-11-02-50/+43
|\
| * rockchip: use rockchip linux partitions layoutJacob Chen2016-10-30-46/+39
| | | | | | | | | | | | | | | | | | | | | | | | Unify the partitions of each chip then it will be more easy for us to write scripts, tools or guides for rockchip chips. Those extra partitions mostly are used to be compatible with our internal loaders (such as miniloader which was same as spl, or android loader then we can support dual boot) Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
| * evb-rk3399: config: set emmc as default boot devKever Yang2016-10-30-1/+1
| | | | | | | | | | | | | | | | | | | | | | rk3399 has two mmc dev controller: mmc 0: SD card; mmc 1: EMMC U-Boot will scan the mmc boot device configured by CONFIG_SYS_MMC_ENV_DEV, since evb has emmc on board, let's set the EMMC as default. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
| * rockchip: RK3288 needs fdt and initrd below 256M nowSandy Patterson2016-10-30-3/+3
| | | | | | | | | | | | | | | | | | | | I am not sure why this limit is changing. But my kernel doesn't load when it's above 256. This was testing on the rock2 board. Signed-off-by: Sandy Patterson <apatterson@sightlogix.com> Updated commit subject: Signed-off-by: Simon Glass <sjg@chromium.org>
* | Fix spelling of "resetting".Vagrant Cascadian2016-10-31-2/+2
| | | | | | | | | | | | | | | | Cover-Letter: Fixes several spelling errors for the words "resetting", "extended", "occur", and "multiple". Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Simon Glass <sjg@chromium.org>
* | OMAP3: omap3_logic: Add scripts to boot over network.Adam Ford2016-10-31-3/+16
| | | | | | | | | | | | | | | | Not all networks have a DHCP server configured properly, so these scripts make it easier to boot in that scenario. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | OMAP3: omap3_logic: Remove LCD preboot infoAdam Ford2016-10-31-20/+0
|/ | | | | | | | | | The LCD isn't supported in U-Boot and the LCD is now configured in the device tree, so this code is pointless. V2: Eliminiate erroneous newline. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* sunxi: A64: enable USB supportAmit Singh Tomar2016-10-30-0/+5
| | | | | | | | | | | | | | | | Mostly by adding MACH_SUN50I to some existing #ifdefs enable support for the the HCI0 USB host controller on the A64. Fix up some minor 64-bit hiccups on the way. Add the bare minimum DT bits to the A64 .dtsi and enable the controllers and the PHY on the Pine64. This is limited to the first USB controller at the moment, which is connected to the lower USB socket on the Pine64 board. [Andre: remove unneeded defines, enable OHCI, add commit message] Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: remove unneeded CONFIG_USB_MAX_CONTROLLER_COUNT definesMasahiro Yamada2016-10-30-5/+0
| | | | | | | | | ARCH_SUNXI selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT is not used. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXIJagan Teki2016-10-30-1/+0
| | | | | | | | | | | | CONFIG_SUNXI -> CONFIG_ARCH_SUNXI and removed CONFIG_SUNIX from config_whitelist.txt Cc: Simon Glass <sjg@chromium.org> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini2016-10-28-26/+9
|\
| * board: sama5d2_xplained: Enable an early debug UARTWenyou Yang2016-10-28-0/+2
| | | | | | | | | | | | | | | | | | Enable an early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * board: sama5d2_xplained: Set 'ethaddr' got from AT24MACWenyou Yang2016-10-28-0/+6
| | | | | | | | | | | | | | | | | | If 'ethaddr' is not set, we will get the ethernet address from AT24MAC, and set it to 'ethaddr' variable. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Songjun Wu <songjun.wu@microchip.com> Reviewed-by: Andreas Bießmann <biessmann@corscience.de>
| * board: sama5d2_xplained: Move config options to defconfigsWenyou Yang2016-10-28-25/+0
| | | | | | | | | | | | | | | | Move the config options from the include/configs/sama5d2_xplained.h to configs/sama5d2_xplained_*_defconfig. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * AT91: Correct misspelling of "redundent" in partition namesRobert P. J. Day2016-10-28-2/+2
| | | | | | | | | | Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-10-28-31/+471
|\ \ | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: common/Kconfig configs/dms-ba16_defconfig
| * | imx6: icorem6: Add default mtd nand partition tableJagan Teki2016-10-26-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | icorem6qdl> mtdparts device nand0 <nand>, # parts = 6 0: spl 0x00200000 0x00000000 0 1: uboot 0x00200000 0x00200000 0 2: env 0x00100000 0x00400000 0 3: kernel 0x00400000 0x00500000 0 4: dtb 0x00100000 0x00900000 0 5: rootfs 0x1f600000 0x00a00000 0 Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | imx6: icorem6: Enable MTD device supportJagan Teki2016-10-26-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable MTD device, partition and command support. Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | imx6: icorem6: Add NAND supportJagan Teki2016-10-26-1/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add NAND support for Engicam i.CoreM6 qdl board. Boot Log: -------- U-Boot SPL 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43) Trying to boot from NAND NAND : 512 MiB U-Boot 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43 +0530) CPU: Freescale i.MX6SOLO rev1.3 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 55C Reset cause: WDOG Model: Engicam i.CoreM6 DualLite/Solo Starter Kit DRAM: 256 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 icorem6qdl> Cc: Scott Wood <oss@buserror.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | engicam: icorem6: Add DM_GPIO, DM_MMC supportJagan Teki2016-10-26-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add DM_GPIO, DM_MMC support for u-boot and disable for SPL. Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | dt-bindings: clock: imx6qdl: Add clock definesJagan Teki2016-10-26-0/+274
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add imx6qdl clock header defines support from Linux. "clk: imx: Add clock support for imx6qp" (sha1: ee36027427c769b0b9e5e205fe43aced93d6aa66) Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | imx6: icorem6: Add ENET supportJagan Teki2016-10-26-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add enet support for engicam icorem6 qdl starter kit. - Add pinmux settings - Add board_eth_init TFTP log: -------- Net: FEC [PRIME] Hit any key to stop autoboot: 0 icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb Using FEC device TFTP from server 192.168.2.96; our IP address is 192.168.2.75 Filename 'imx6dl-icore.dtb'. Load address: 0x0 Loading: ###### 1.3 MiB/s done Bytes transferred = 28976 (7130 hex) CACHE: Misaligned operation at range [00000000, 00007130] icorem6qdl> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial supportJagan Teki2016-10-26-0/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot Log for i.CoreM6 DualLite/Solo Starter Kit: ----------------------------------------------- U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46) Trying to boot from MMC1 U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530) CPU: Freescale i.MX6SOLO rev1.3 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 31C Reset cause: POR DRAM: 256 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device switch to partitions #0, OK mmc0 is current device reading boot.scr ** Unable to read file boot.scr ** reading zImage 6741808 bytes read in 341 ms (18.9 MiB/s) Booting from mmc ... reading imx6dl-icore.dtb 30600 bytes read in 19 ms (1.5 MiB/s) Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800a787 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 Boot Log for i.CoreM6 Quad/Dual Starter Kit: -------------------------------------------- U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46) Trying to boot from MMC1 U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530) CPU: Freescale i.MX6Q rev1.2 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 28C Reset cause: POR DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | config: Move CONFIG_DEFAULT_FDT_FILE to defconfigsJagan Teki2016-10-26-23/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Add DEFAULT_FDT_FILE kconfig entry - Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * | mx6sabresd: Add Falcon mode supportDiego Dorta2016-10-17-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | Allow i.MX6Q Sabre SD to load the kernel and dtb via SPL in Falcon mode. Based on the Falcon mode code for MX6 Gateworks Ventana board. Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
| * | mx7_common: add secure boot supportGary Bisson2016-10-17-8/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Selecting the proper options to enable the build of the HAB tools. Note, this support is disabled by default, one will have to select the SECURE_BOOT configuration through menuconfig to enable it. See doc/README.mxc_hab for more details. Also remove duplicate options from board config headers. Cc: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
| * | mx6_common: add secure boot supportGary Bisson2016-10-17-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Selecting the proper options to enable the build of the HAB tools. Note, this support is disabled by default, one will have to select the SECURE_BOOT configuration through menuconfig to enable it. See doc/README.mxc_hab for more details. Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
* | | pci: Move CONFIG_PCI_PNP to KconfigBin Meng2016-10-28-183/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig to use that. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Re-generate configs and include/configs/ changes] Signed-off-by: Tom Rini <trini@konsulko.com>
* | | drivers/pci/Kconfig: Add PCITom Rini2016-10-27-130/+0
| |/ |/| | | | | | | | | | | Add 'PCI' as a menu option and migrate all existing users. Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stephen Warren <swarren@nvidia.com>
* | Merge git://git.denx.de/u-boot-fdtTom Rini2016-10-24-6/+18
|\ \
| * | libfdt: Sync overlay with upstreamMaxime Ripard2016-10-23-6/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the overlay code has been merge upstream, update our copy to what's been merged, since a significant number of issues have been fixed during the merge process. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Simon Glass <sjg@chromium.org>
* | | Convert CONFIG_SYS_STDIO_DEREGISTER to KconfigSimon Glass2016-10-23-21/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_STDIO_DEREGISTER This option should never be enabled in SPL, so use CONFIG_IS_ENABLED(SYS_STDIO_DEREGISTER) when checking the option. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-sync] Signed-off-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_USB_KEYBOARD to KconfigSimon Glass2016-10-23-20/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_USB_KEYBOARD Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Fixup MPC86* configs] Signed-off-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_SYS_CONSOLE_INFO_QUIET to KconfigSimon Glass2016-10-23-67/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_CONSOLE_INFO_QUIET Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Make this default n, re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to KconfigSimon Glass2016-10-23-30/+0
| | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_SYS_CONSOLE_ENV_OVERWRITE to KconfigSimon Glass2016-10-23-17/+0
| | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_CONSOLE_ENV_OVERWRITE Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_CONSOLE_SCROLL_LINES to KconfigSimon Glass2016-10-23-23/+0
| | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CONSOLE_SCROLL_LINES Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | video: Drop CONFIG_CONSOLE_INFO_QUIETSimon Glass2016-10-23-5/+0
| | | | | | | | | | | | | | | | | | | | | This is not used in U-Boot. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | video: Move video_get_info_str() prototype to a header fileSimon Glass2016-10-23-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | This should be defined in a header file so that arguments are checked. Move it to video.h. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_CONSOLE_EXTRA_INFO to KconfigSimon Glass2016-10-23-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CONSOLE_EXTRA_INFO Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_VIDEO_SW_CURSOR to KconfigSimon Glass2016-10-23-31/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_VIDEO_SW_CURSOR Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Re-convert, find all the cases where this is off] Signed-off-by: Tom Rini <trini@konsulko.com>
* | | video: Drop CONFIG_VIDEO_HW_CURSORSimon Glass2016-10-23-4/+0
| | | | | | | | | | | | | | | | | | | | | This is not used in U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | Convert CONFIG_VGA_AS_SINGLE_DEVICE to KconfigSimon Glass2016-10-23-62/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_VGA_AS_SINGLE_DEVICE Once we migrate to driver model for video, we should be able to drop this option. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-11-10 05:41:26 +0000