summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
...
| * | | am335x_evm: Bring in 'boot_fdt' logic from i.MXTom Rini2013-08-15-5/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Bring in the 'boot_fdt' environment variable that i.MX boards use to try and load a device tree when booting. Signed-off-by: Tom Rini <trini@ti.com>
| * | | am335x_evm: Use default baud rate tableTom Rini2013-08-15-2/+0
| | | | | | | | | | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| * | | am33xx: Stop using PHYS_DRAM_1 defineTom Rini2013-08-15-8/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1 in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and then using that name in code. Signed-off-by: Tom Rini <trini@ti.com>
| * | | am33xx: CONFIG_DMA_COHERENT defines are unused, removeTom Rini2013-08-15-10/+0
| | | | | | | | | | | | | | | | | | | | Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
| * | | OMAP3: igep00x0: allow booting with a FDT from MMCJavier Martinez Canillas2013-08-15-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | IGEP boards now have Device Tree support in the mainline kernel. To boot an IGEP board using a DT, a uEnv.txt plain text file could be used to define a custom uenvcmd that will be run by the default boot command. It is more convenient to change the default boot command to allow loading a FDT if it is stored in the boot dir of the rootfs uSD/MMC partition. If no FDT is found then the defaul command tries to boot a zImage without a DT using legacy boot. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
| * | | ARM: igep00x0.h: Enable the use of CMD_EXT4, CMD_FS_GENERIC and zImage.Enric Balletbo i Serra2013-08-15-6/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Able to load the kernel from some form of ext[234] or FAT. Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore by default, so we should switch to use the bootz command. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
| * | | ARM: IGEP0033: Remove duplicate / unused #defines.Enric Balletbo i Serra2013-08-15-7/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As config was originally based on am335x_evm.h we have also some duplicate / unnused #defines. Commit 15191c91 removed these #defines on various AM335x boards but not for IGEP COM AQUILA. This patch simply removes them for this board. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
| * | | ARM: IGEP0033: Add support to boot from NAND.Enric Balletbo i Serra2013-08-15-5/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add to the default environment the possibily to boot from NAND using a ubi rootfs. Also the partition scheme is set as follows: Start Size SPL : 0x00000000 0x00080000 (512KiB) U-Boot : 0x00080000 0x00100000 (1MiB) U-Boot Env : 0x00180000 0x00020000 (128KiB) File System : 0x001C0000 - The ubiboot script gets the kernel and the dtb file from the boot directory of the File System. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
| * | | ARM: IGEP0033: Add support for Flattened Device Tree.Enric Balletbò i Serra2013-08-15-20/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now, the default kernel to boot the IGEP COM AQUILA is device tree based. As old kernel is deprecated we should adapt the boot commands to use DTB files. Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore by default, so we should switch to use the bootz command. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
| * | | ARM: IGEP0033: Remove undef of CONFIG_CMD_MEMTESTEnric Balletbo i Serra2013-08-15-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After commit: 79cd2f814b1c75efd47161ac27f4cbebf768240f config_cmd_default.h: Remove CONFIG_CMD_MEMTEST It's not necessary to undef the CONFIG_CMD_MEMTEST, so we can remove it from configuration file. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
| * | | ARM: AM43xx: Add config fileLokesh Vutla2013-08-15-0/+135
| | | | | | | | | | | | | | | | | | | | | | | | Add config file Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * | | ARM: OMAP: Add CONFIG_OMAP_COMMONLokesh Vutla2013-08-15-0/+25
| | |/ | |/| | | | | | | | | | | | | | | | Adding a new CONFIG_OMAP_COMMON which is included by all boards that needs to build cpu/armv7/omap-common folder. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * | gpio: omap5-uevm: Configure the tca6424 gpio expanderDan Murphy2013-07-30-0/+5
| | | | | | | | | | | | | | | | | | | | | Configure the tca6424 gpio expander This allows use of the debug and tri color LEDs. Signed-off-by: Dan Murphy <dmurphy@ti.com>
| * | gpio: tca642x: Add the tca642x gpio expander driverDan Murphy2013-07-30-0/+69
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add the tca642x gpio expander driver Datasheet: http://www.ti.com/product/tca6424a Signed-off-by: Dan Murphy <dmurphy@ti.com>
| * | am335x_evm: Add support for eMMC environmentJustin Waters2013-07-30-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | Some boards, such as the BeagleBone Black, have an eMMC chip intstead of NAND. We can use the eMMC boot partition to store the environment, since it isn't used for anything else. This allows us to have a configurable environment on those boards. Signed-off-by: Justin Waters <justin.waters@timesys.com>
| * | am335x_evm: Rework bootcmd to handle two MMC devsJustin Waters2013-07-30-20/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The BeagleBone Black can boot from either the MMC card or eMMC chip on board. We should try both interfaces. This modification also allows a graceful fallback if a device exists but boot images are not present on it. Changes for v2: * Fix boot partition - it should always show up as mmcblk0p2 * Fix missing FDT load Signed-off-by: Justin Waters <justin.waters@timesys.com>
| * | am335x_evm: Add command line editingJustin Waters2013-07-30-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | Many modern U-Boot ports enable command line editing and a history buffer. The am335x_evm configuration is fairly comprehensive as it is, so a few extra kb should not be noticable, and it adds a very convenient feature. Signed-off-by: Justin Waters <justin.waters@timesys.com>
| * | am335x_evm: Make NAND support modularJustin Waters2013-07-30-19/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Give the user the ability to disable NAND support by defining CONFIG_NO_NAND. This will allow custom hardware to easily support this configuration. Signed-off-by: Justin Waters <justin.waters@timesys.com> [trini: Make apply on top of other series] Signed-off-by: Tom Rini <trini@ti.com>
| * | am335x_evm: Add support to boot from NOR.Steve Kipisz2013-07-30-2/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NOR requires that s_init be within the first 4KiB of the image so that we can perform the rest of the required pinmuxing to talk with the rest of NOR that we are found on. When NOR_BOOT is set we save our environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid using SPL for this case and u-boot.bin is written directly to the start of NOR. We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c with TI81xx checks as at this time U-Boot does not discard unused sections in the main build and this code relies on functions specific to (and only provided in) ti81xx-related code. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
| * | am335x_evm: Add support for the NOR module on the memory capeSteve Kipisz2013-07-30-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the NOR module that attaches to the memory cape for a Beaglebone board. This does not add booting support; only support so that you can boot from SD/MMC and see the NOR module so that it can be programmed. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Clean up config changes slightly] Signed-off-by: Tom Rini <trini@ti.com>
| * | am335x_evm: Update SPI_BOOT support, add MTDPARTS infoTom Rini2013-07-30-21/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Style cleanup (# define -> #define) - Due to ROM issues, redudant loading isn't feasible, so drop. - Given extra space, increase max size of U-Boot to 512KiB - Correct env size to match usage (we had not re-defined ENV_SIZE). - Given extra space, keep env size as 128KiB, add redundant environment. Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Tom Rini <trini@ti.com>
| * | am335x_evm: Drop useless CONFIG_ENV_IS_NOWHERETom Rini2013-07-30-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | We always set a CONFIG_ENV_IS_...somewhere... so drop the initial define of NOWHERE. Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Tom Rini <trini@ti.com>
| * | omap3_beagle: support booting from zImage and device tree as last optionNishanth Menon2013-07-26-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If no other bootoption works, try loading up device tree and zImage. This is selected as the last option to allow backward compatibility as well as support the recent trend in moving kernel boot to using zImage and device tree. NOTE: if uImage is present in bootpart, it will try this first and will assume this is to be booted with bootm (so may be concatenated image or plain vanilla ATAG MACHINE_ID based image) Signed-off-by: Nishanth Menon <nm@ti.com>
| * | omap3_beagle: support findfdt and loadfdt for devicetree supportNishanth Menon2013-07-26-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For folks not using concatenated device tree with uImage, having an handy function to find and load device tree is very handy. So introduce findfdt and loadfdt and run findfdt by default to make it easier on user scripts. Signed-off-by: Nishanth Menon <nm@ti.com>
| * | omap3_beagle: enable CMD_FS_GENERIC and simplify load of image/ramdiskNishanth Menon2013-07-26-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CMD_FS_GENERIC allows us to simplify where we load up our image from either from ext2/fat etc. So, lets use that instead of cumbersome options we currently use. Sticking with existing conventions, defaults will be: ramdisk=ramdisk.gz bootpart=0:2 (second partition) bootdir=/boot (/boot in second partition) This matches with the default behavior, these can be overriden by env files as needed. Signed-off-by: Nishanth Menon <nm@ti.com>
| * | omap3_beagle: replace uImage.beagle with generic uImageNishanth Menon2013-07-26-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | e682930867f7dfc4a01784fe452fad9e962d65a (BeagleBoard: config: use uImage.beagle for tftp) Introduced uImage.beagle which does not happen to be default output file of Linux kernel build make uImage (output is uImage). So, replace uImage.beagle with uImage Signed-off-by: Nishanth Menon <nm@ti.com>
| * | omap3_beagle: remove JFFS2 support.Nishanth Menon2013-07-26-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | We do not use JFFS2 by default and it conflicts with CONFIG_CMD_FS_GENERIC (ls command is the same). Since most of our BOOTCMD can be simplified by using the FS_GENERIC, dropping JFFS2 Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Joel Fernandes <joelf@ti.com>
| * | ARM: DRA7xx: Enable CPSW Ethernet supportMugunthan V N2013-07-26-0/+19
| | | | | | | | | | | | | | | | | | Enabling CPSW Ethernet support in DRA7xx EVM. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * | drivers: net: cpsw: remove hard coding bd ram for cpswMugunthan V N2013-07-26-0/+1
| | | | | | | | | | | | | | | | | | | | | BD ram address may vary in various SOC, so removing the hardcoding and passing the same information through platform data Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * | am335x_evm: Correct CONFIG_CMD_SPL_WRITE_SIZETom Rini2013-07-26-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | We use CONFIG_CMD_SPL_WRITE_SIZE when reading/writing the args portion of falcon mode to NAND. Previously it was half the size of the eraseblock which is too small, increase to eraseblock size. Signed-off-by: Tom Rini <trini@ti.com>
| * | am335x_evm: Update eMMC falcon mode locationsTom Rini2013-07-26-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The previous location used for the "args" portion of falcon mode was too small to allow for a device tree to be saved there, so move the location slightly and increase the size. In addition, our previous kernel location was part of the area we set aside for U-Boot itself, so move it up a bit higher. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
| * | am335x_evm: Correct DFU ALT settings for falcon modeTom Rini2013-07-26-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have falcon mode enabled, the partiton numbers for NAND have changed, and we need to list entries for updating these parts of the system. While adding falcon mode entires for eMMC (raw), we round up the limit on U-Boot for ease of math later. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
| * | Merge branch 'u-boot/master' into u-boot-arm/masterAlbert ARIBAUD2013-07-25-14693/+3111
| |\ \
| * | | highbank: enable keyed autoboot stopRob Herring2013-07-25-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Restrict autoboot interruption to "s" or "d" keys. This will prevent some unwanted stopping and also allow disabling the reset on command timeout. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | | ARM: highbank: setup peripherals based on power domain statusRob Herring2013-07-25-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Accessing powered down peripherals will hang the bus, so check power domain status before initializing SATA and fixup the FDT to disable unused peripherals. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | | ARM: highbank: enable reset on command timeoutRob Herring2013-07-25-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable resetting on command timeout. The timeout is set with environment setting bootretry. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | | ARM: highbank: update config optionsRob Herring2013-07-25-2/+12
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Various changes to highbank config: Enable EFI partitions Enable ext4 and FAT filesystems Enable bootz command and raw initrd Increase cmd and print buffer size to 1K Change serial baudrate to 115200 Enable hush shell Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2013-08-14-0/+64
|\ \ \
| * | | include/fsl_usb.h: Cleanup license headerYork Sun2013-08-14-17/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace license header with SPDX license identifier. Replace GPL-2.0 with GPL-2.0+. Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
| * | | fsl/usb: Move USB internal phy definitions to fsl_usb.hramneek mehresh2013-08-14-0/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | fsl_usb.h file created to share data bewteen usb platform code and usb ip driver. Internal phy structure definitions moved to this file Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* | | | Merge branch 'dcc' of git://www.denx.de/git/u-boot-microblazeTom Rini2013-08-13-3/+0
|\ \ \ \ | |/ / / |/| | |
| * | | serial: arm_dcc: Remove stdio structure supportJagannadha Sutradharudu Teki2013-08-13-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed stdio structure ops support on arm_dcc driver, and need to register with serial core so-that it can access like remianing serial drivers. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2013-08-13-586/+1849
|\ \ \ \
| * | | | powerpc/mpc85xx: Cleanup license header in source filesYork Sun2013-08-12-51/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the license header introduced by the following patches Add TWR-P10xx board support Add T4240EMU target IDT8T49N222A configuration code Add C29x SoC support Add support for C29XPCIE board Signed-off-by: York Sun <yorksun@freescale.com>
| * | | | powerpc/c29xpcie: add support for C29XPCIE boardMingkai Hu2013-08-09-0/+472
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | C29XPCIE board is a series of Freescale PCIe add-in cards to perform as public key crypto accelerator or secure key management module. It includes C293PCIE board, C293PCIE board and C291PCIE board. - 512KB platform SRAM in addition to 512K L2 Cache/SRAM - 512MB soldered DDR3 32bit memory - CPLD System Logic - 64MB x16 NOR flash and 4GB x8 NAND flash - 16MB SPI flash Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Singed-off-by: Po Liu <Po.Liu@freescale.com> [yorksun: Fixup include/configs/C29XPCIE.h] Signed-off-by: York Sun <yorksun@freescale.com>
| * | | | powerpc/pcie: add PCIe version 3.x supportZang Roy-R619112013-08-09-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T4240 PCIe IP is version 3.0 and has some update comparing previous QorIQ products. 1. Move Freescale specific register define to arch/powerpc/include/asm/fsl_pci.h and update the register offset define for T4240. 2. add the status/control register define use status/control register to judge the link status 3. The original code uses 'Programming Interface' field to judge if PCIE is EP or RC mode, however, T4240 does not support this functionality. According to PCIE specification, 'Header Type' offset 0x0e is used to indicate header type, so for PCIE controller, the patch changes code to use 'Header Type' field to identify if the PCIE is RC or EP mode. This patch fixes the PCIe card link up issue on T4240QDS. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
| * | | | powerpc/rman: fix RMan support for t4240 and b4860Minghuan Lian2013-08-09-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860. 2. Decrease RMan liodn offset number. SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3. For t4240 and b4860, RMan liodn base is assigned to 922, the original offset number is too large that the liodn (base+offset 922+678 = 1600) is greater than 0x500 the maximum liodn number. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
| * | | | board/b4860qds: Add support for configuring SerDes1 RefclksShaveta Leekha2013-08-09-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1) Add support in B4860 board files for using IDT driver where IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer that generate different refclks for SerDes modules, used this driver for reconfiguring SerDes1 Refclks(based on SerDes1 protocols) for CPRI to work. CPRI works on 122.88MHz and default refclks coming on board are not suitable for it 2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file to b4860qds board file, as SerDes1 Refclk1 would come from PHY MUX in case of certain protocols, that have been checked here. This change would make on board SGMIIs to work 3) Add I2C addresses for IDT8T49N222A devices in board/include file 4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
| * | | | board/bsc9132qds: Add DSP side tlb and lawsPriyanka Jain2013-08-09-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a integrated device that contains two powerpc e500v2 cores and two DSP starcores. To support DSP starcore -Creating LAW and TLB for DSP-CCSR space. -Creating LAW for DSP-core subsystem M2 and M3 memory -Creating LAW for 1GB DDR which is connected exclusively to DSP-cores Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
| * | | | p1020rdb-pd: platform supportHaijun.Zhang2013-08-09-3/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB. DDR changed from DDR2 1G to DDR3 2G. NAND: 128 MiB Flash: 64 MiB Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> CC: Scott Wood <scottwood@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
generated by cgit v1.1 at 2024-09-20 01:25:44 +0000