summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* pm9263: use macro instead of hardcode value for the lowlevel_initJean-Christophe PLAGNIOL-VILLARD2009-06-21-28/+82
| | | | | | | optimize a few the RAM init Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* pm9263: lowlevel init updateJean-Christophe PLAGNIOL-VILLARD2009-06-21-9/+1
| | | | | | | move PSRAM init to pm9263.c this will allow us after to make the nor lowlevel_init generic Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Blackfin: fix SPI flash speed define nameMike Frysinger2009-06-15-11/+11
| | | | | | | The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf548-ezkit: bump up monitor sizeMike Frysinger2009-06-15-1/+1
| | | | | | | The latest version of U-Boot got a bit fatter in the BSS section which caused overflows in the RAM region, so increase the monitor size. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf533-stamp/bf537-stamp: fix env settings for SPI flashVivi Li2009-06-15-4/+4
| | | | | | | | | The SPI flash layer is much stricter about sector usage than the eeprom layer we used to use, so update the env settings to better match the sector alignment of the flashes we use. Signed-off-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk2009-06-15-1/+91
|\
| * Convert DM9000 driver for CONFIG_NET_MULTIRemy Bohmer2009-06-15-0/+5
| | | | | | | | | | | | | | | | | | All drivers need to be converted to CONFIG_NET_MULTI. This patch converts the dm9000 driver. Signed-off-by: Thomas Smits <ts.smits@gmail.com> Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * net: Add Marvell Kirkwood gigabit ethernet driverPrafulla Wadaskar2009-06-15-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a egiga driver for the Marvell Kirkwood SoC's. Contributors: Yotam Admon <yotam@marvell.com> Michael Blostein <michaelbl@marvell.com Reviewed-by: Ronen Shitrit <rshitrit@marvell.com> Acked-by: Stefan Rose <sr@denx.de> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * DaVinci Network Driver Updatess-paulraj@ti.com2009-06-15-1/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Different flavours of DaVinci SOC's have differences in their EMAC IP This patch does the following 1) Updates base addresses for DM365 2) Updates MDIO frequencies for DM365 and DM646x 3) Update EMAC wrapper registers for DM365 and DM646x Patch applies to u-boot-net git. the EMAC driver itself will be updated shortly to add support for DM365 and DM646x Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * Switched davinci_emac Ethernet driver to use newer APIBen Warren2009-06-15-0/+5
| | | | | | | | | | | | | | | | Added CONFIG_NET_MULTI to all Davinci boards Removed all calls to Davinci network driver from board code Added cpu_eth_init() to cpu/arm926ejs/cpu.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * Marvell MV88E61XX Switch Driver supportPrafulla Wadaskar2009-06-15-0/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Chips supported:- 1. 88E6161 6 port gbe swtich with 5 integrated PHYs 2. 88E6165 6 port gbe swtich with 5 integrated PHYs 2. 88E6132 3 port gbe swtich with 2 integrated PHYs Platform specific configuration supported for:- default or router port vlan configuration led_init configuration mdip/n polarity reversal configuration Note: This driver is supported and tested against kirkwood egiga interface Contributors: Yotam Admon <yotam@marvell.com> Michael Blostein <michaelbl@marvell.com Reviewed by: Ronen Shitrit <rshitrit@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * tsec: Add support for BCM5482S PHYZach LeRoy2009-06-15-0/+2
| | | | | | | | | | | | Signed-off-by: Zach LeRoy <zleroy@xes-inc.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | Blackfin: unify u-boot linker scriptsMike Frysinger2009-06-14-0/+124
| | | | | | | | | | | | | | | | | | | | | | All the Blackfin linker scripts were duplicated across the board dirs with no difference save from the semi-often used ENV_IS_EMBEDDED option. So unify all of them in the lib_blackfin/ dir and for the few boards that need to embedded the environment directly, add a LDS_BOARD_TEXT define for them to customize via their board config file. This is much simpler than forcing them to duplicate the rest of the linker script. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf518f-ezbrd: enable SST SPI flash driverMike Frysinger2009-06-14-0/+1
| | | | | | | | | | | | | | The BF51xF parts have an internal SST SPI flash, so make sure the driver is enabled by default so we can access it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: convert specific pre/post config headers to common methodMike Frysinger2009-06-14-231/+166
| | | | | | | | | | | | | | | | | | | | The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup common Blackfin board defines. The common method now is to use config.h, so convert blackfin-config-post.h to that. Rename the still Blackfin specific blackfin-config-pre.h to config-pre.h so the naming conventions at least line up. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: enable LZMA for all ADI boardsMike Frysinger2009-06-14-0/+5
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: make default ADI env more flexibleMike Frysinger2009-06-14-5/+25
| | | | | | | | | | | | | | | | Allow boards to easily override the root= and default bootcmd, allow people to tweak the file used in default bootcmds at runtime via one env var, and add a stock nandboot command. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: ibf-dsp561: new board portHoan Hoang2009-06-14-0/+130
| | | | | | | | | | Signed-off-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: blackstamp: new board portMike Frysinger2009-06-14-0/+275
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf537-srv1: new board portMike Frysinger2009-06-14-0/+204
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf537-minotaur: new board portMike Frysinger2009-06-14-0/+204
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf537-pnav: new board portMike Frysinger2009-06-14-0/+172
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf527: new board portMike Frysinger2009-06-14-0/+137
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf548: new board portMike Frysinger2009-06-14-0/+141
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: tcm-bf537: new board portMike Frysinger2009-06-14-0/+125
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf561: new board portMike Frysinger2009-06-14-0/+104
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf537e: new board portMike Frysinger2009-06-14-0/+124
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf533: new board portMike Frysinger2009-06-14-0/+104
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: new spibootldr commandMike Frysinger2009-06-14-0/+28
|/ | | | | | | Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes, so add a new 'spibootldr' command to take advantage of it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 85xx: Add PORBMSR and PORDEVSR shift definesPeter Tyser2009-06-12-0/+2
| | | | | | | | | Add defines similar to those already used for the the 86xx architecture. This will ease sharing of PCI code between the 85xx and 86xx architectures. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl/85xx, 86xx: Sync up DMA codePeter Tyser2009-06-12-0/+2
| | | | | | | | | | | | | | | | | | | | | The following changes were made to sync up the DMA code between the 85xx and 86xx architectures which will make it easier to break out common 8xxx DMA code: 85xx: - Don't set STRANSINT and SPCIORDER fields in SATR register. These bits only have an affect when the SBPATMU bit is set. - Write 0xffffffff instead of 0xfffffff to clear errors in the DMA status register. We may as well clear all 32 bits of the register... 86xx: - Add CONFIG_SYS_MPC86xx_DMA_ADDR define to address DMA registers - Add clearing of errors in the DMA status register when initializing the controller - Clear the channel start bit in the DMA mode register after a transfer Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl: Create common fsl_dma.h for 85xx and 86xx cpusPeter Tyser2009-06-12-146/+57
| | | | | | | | Break out DMA structures for the Freescale MPC85xx and MPC86xx cpus to reduce a large amount of code duplication Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add UEC6 and UEC8 at SGMII mode for MPC8569MDSHaiying Wang2009-06-12-0/+25
| | | | | | | | | On MPC8569MDS board, UCC6 and UCC8 can be configured to work at SGMII mode via UEM on PB board. Since MPC8569 supports up to 4 Gigabit Ethernet ports, we disable UEC6 and UEC8 by default. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add RMII support for MPC8569MDSHaiying Wang2009-06-12-4/+34
| | | | | | | | | This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to enalbe_mpc8569mds_qe_uec which is more accurate. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add UEC3 and UEC4 support for MPC8569MDSHaiying Wang2009-06-12-0/+23
| | | | | Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* drivers/qe: Add more SNUM number for QEHaiying Wang2009-06-12-1/+4
| | | | | | | | | Some QE chips like 8569 need more SNUM numbers for supporting 4 UECs in RGMII- 1000 mode. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* drivers/qe: Change QE RISC ALLOCATION to support 4 RISCsHaiying Wang2009-06-12-0/+8
| | | | | | | | | Also define the QE_RISC_ALLOCATION_RISCs to MACROs instead of using enum, and define MAX_QE_RISC for QE based silicons. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add QE clk supportHaiying Wang2009-06-12-0/+3
| | | | | | Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Acked-by: Timur Tabi <Timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Added MPC8535/E identifiersKumar Gala2009-06-12-0/+2
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add P2020DS supportSrikanth Srinivasan2009-06-12-0/+741
| | | | | | | | | | | | | The patch adds support for P2020DS reference platform. DDR3 interface uses hard-coded initialization rather than SPD for now and was tested at 667Mhz. Some PIXIS register definitions and associated code sections need to be fixed. TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all tested under u-boot. Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc512x: MPC5121ADS: Add NAND supportStefan Roese2009-06-12-1/+21
| | | | | | | | | | This patch adds NAND support to the MPC5121ADS board. Please note that the image size increased since NAND support didn't fit in the current image size (256k). Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* mpc512x: Add esd gmbh mecp5123 board supportStefan Roese2009-06-12-0/+458
| | | | | | | MECP5123 is a MPC5121E based module by esd gmbh. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* mcp512x: Add macros for SCFR LPC divisor accessStefan Roese2009-06-12-0/+3
| | | | | | Thos macros will be used by the esd mecp5123 board. Signed-off-by: Stefan Roese <sr@denx.de>
* 74xx_7xx: CPCI750: Add CPCI adapter/target supportStefan Roese2009-06-12-0/+2
| | | | | | | | The CPCI750 can be built as CPCI host or adapter/target board. This patch adds support for runtime detection of those variants. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* 74xx_7xx: CPCI750: Add commandline editing/historyStefan Roese2009-06-12-1/+2
| | | | | Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* mpc85xx: 8536ds: Add USB related CONFIGsVivek Mahajan2009-06-12-2/+12
| | | | | | | | | This patch adds CONFIGs for enabling USB in mpc8536ds and also adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its Copyright. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc83xx: 8315erdb: Add USB related CONFIGsVivek Mahajan2009-06-12-1/+10
| | | | | | | | | This patch adds CONFIGs for enabling USB in mpc8315erdb and also adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its Copyright. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc85xx: USB: Add supportVivek Mahajan2009-06-12-1/+6
| | | | | | | | The following patch adds 85xx-specific USB support and also revamps Copyright in immap_85xx.h Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc83xx: USB: Reorganized its supportVivek Mahajan2009-06-12-2/+66
| | | | | | | | | | | | | | | | | The following patch reorganizes/reworks the USB support for mpc83xx as under:- * Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to cpu/mpx83xx/cpu_init.c * Board specific usb_phy_type is read from the environment * Adds USB EHCI specific structure in include/usb/ehci-fsl.h * Copyrights revamped in most of the following files Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc8xxx: USB: Relocates ehci-fsl.h to include/usbVivek Mahajan2009-06-12-0/+86
| | | | | | | | The following patch moves 8xxx-specifc USB #defines from drivers/usb/host/ehci-fsl.h to include/usb. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
generated by cgit v1.1 at 2024-12-21 01:39:53 +0000