summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* OMAP3: igep00x0: Convert to ti_omap3_common.h.Enric Balletbò i Serra2014-01-24-180/+9
| | | | | | To reduce code duplication update omap3_igep00x0.h to use ti_omap3_common.h. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
* TI: OMAP3: Create common config files for TI OMAP3 platforms.Enric Balletbò i Serra2014-01-24-0/+73
| | | | | | | | Create a new file, include/configs/ti_omap3_common.h, for everything common to the OMAP3 SoC leaving just the board specific part to board configuration file. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
* TI: armv7: Do not define the number DRAM banks if is already defined.Enric Balletbò i Serra2014-01-24-3/+7
| | | | | | | | | | If CONFIG_NR_DRAM_BANKS is not defined, we say (for simplicity) that we have 1 bank, but for some boards should be interesting that we can define CONFIG_NR_DRAM_BANKS. To handle this possibility just define the number of DRAM banks if is not already defined. This is useful for some OMAP3 boards where the DRAM initialitzation is only at u-boot level. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
* TI: armv7: Move ELM support to SoC configuration file.Enric Balletbò i Serra2014-01-24-1/+12
| | | | | | | | | The ELM hardware engine wihich is used for ECC error detections is not present on OMAP3 SoC, so move the CONFIG_SPL_NAND_AM33XX_BCH from ti_armv7_common.h to SoC configuration file. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5: Rename to ti_omap5_common.hEnric Balletbò i Serra2014-01-24-7/+7
| | | | | | | | Follow the pattern ti_<processor family>_common.h used by other TI processors to be coherent. So just rename omap5_common.h to ti_omap5_common.h. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP4: Rename to ti_omap4_common.hEnric Balletbò i Serra2014-01-24-7/+7
| | | | | | | | Follow the pattern ti_<processor family>_common.h used by other TI processors to be coherent. So just rename omap4_common.h to ti_omap4_common.h. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* arm: koelsch: Add support QSPI device and enable boot from SPI flashNobuhiro Iwamatsu2014-01-16-4/+28
| | | | | | | | This supports SH-QSPI device on koelsch board, and enable booting from SPI flash. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* arm: lager: Add support QSPI device and enable boot from SPI flashNobuhiro Iwamatsu2014-01-16-4/+29
| | | | | | | | This supports SH-QSPI device on lager board, and enable booting from SPI flash. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2014-01-15-0/+226
|\
| * mx6: Add initial support for the Hummingboard soloFabio Estevam2014-01-15-0/+226
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SolidRun has designed the Hummingboard board based on mx6q/dl/solo. Add the initial support for the mx6 solo variant. More information about this hardware can be found at: http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware (Carrier-One was the previous name of Hummingboard). Based on the work from Jon Nettleton <jon.nettleton@gmail.com>. Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | Merge 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2014-01-14-10/+36
|\ \ | |/
| * mx6slevk: Include "mx6_common.h"Fabio Estevam2014-01-13-0/+1
| | | | | | | | | | | | | | | | Include "mx6_common.h" so that some ARM errata are applied and also the vddsoc regulator can be changed. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * wandboard: Set default environment to use zImageJohn Weber2014-01-13-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. The zImage works for FSL Linux's kernel fork versions 3.0.35, 3.10.9, and 3.10.17; this also works fine for mainline kernels. Signed-off-by: John Weber <rjohnweber@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
| * mx6sabresd: Add eMMC specific environment to allow U-Boot updateOtavio Salvador2014-01-13-0/+25
| | | | | | | | | | | | | | | | A new 'update_emmc_firmware' target is added to allow for easy U-Boot update in the eMMC as it has secury boot partition and this needs specific handling on how to program the specific partition. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* | mx1ads: remove board supportAlbert ARIBAUD2014-01-14-163/+0
| | | | | | | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Stefano Babic <sbabic@denx.de>
* | ARM: pxa: Fix OneNAND window access on VPAC270Marek Vasut2014-01-13-1/+1
| | | | | | | | | | | | | | | | | | | | Access the OneNAND 1KiB window on the VPAC270 as an SRAM instead of accessing it as a burst-RAM. This fixes a problem where the board failed to reboot sometimes as the CPU couldn't start executing from the OneNAND 1KiB window. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-01-10-869/+1833
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be added to include/configs/exynos5-dt.h now. Conflicts: include/configs/exynos5250-dt.h Signed-off-by: Tom Rini <trini@ti.com>
| * | zynq: Enable CONFIG_DEFAULT_DEVICE_TREEJagannadha Sutradharudu Teki2014-01-10-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enabled default dts files on respective pre-board config files this is way MAKEALL will works. and it's upto user to build specific dts by specifying at build time. $ make zynq_zc70x_config $ make --> with default dts zynq-zc702.dts or $ make DEVICE_TREE=zynq-zc702 --> Same configuration with zynq-zc706.dts Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq-common: Enable verified boot(RSA)Jagannadha Sutradharudu Teki2014-01-10-0/+4
| | | | | | | | | | | | | | | | | | | | | CONFIG_FIT_SIGNATURE - signature node support in FIT image CONFIG_RSA - RSA lib support Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | dts: zynq: Add basic fdt supportJagannadha Sutradharudu Teki2014-01-10-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch provides a basic fdt support for zynq u-boot. zynq-7000.dtsi-> initial arch dts file zynq-zed.dts -> initial zed board dts file more devices should be added in subsequent patches. u-boot build: once configuring of a board done for building dtb with zynq-zed.dts as an input zynq-uboot> make DEVICE_TREE=zynq-zed Enabled CONFIG_OF_SEPARATE for building dtb separately. There is a new binary called u-boot-dtb.bin which is a u-boot with devicetree supported. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq-common: Define CONFIG_ENV_OVERWRITEJagannadha Sutradharudu Teki2014-01-10-0/+3
| | | | | | | | | | | | | | | | | | | | | Defined CONFIG_ENV_OVERWRITE, which allow to overwrite serial baudrate and ethaddr. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq-common: Define flash env. partitionJagannadha Sutradharudu Teki2014-01-10-1/+11
| | | | | | | | | | | | | | | | | | | | | Last 128Kb sector of 1Mb flash is defined as u-boot environment partition. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq-common: Change Env. Sector size to 128KbJagannadha Sutradharudu Teki2014-01-10-1/+3
| | | | | | | | | | | | | | | | | | Changed Env. Sector size from 0x10000 to 128Kb Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq-common: Define default environmentJagannadha Sutradharudu Teki2014-01-10-1/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Defined default env. for autoboot FIT image from respective boot devices. Default settings: fit_image=fit.itb load_addr=0x2000000 fit_size=0x800000 flash_off=0x100000 nor_flash_off=0xE2100000 Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add support to find bootmodeJagannadha Sutradharudu Teki2014-01-10-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Added support to find the bootmodes by reading slcr bootmode register. this can be helpful to autoboot the configurations w.r.t a specified bootmode. Added this functionality on board_late_init as it's not needed for normal initializtion part. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add zynq_zc770 xm012 board supportJagannadha Sutradharudu Teki2014-01-10-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZC770 is a complete development board based on the Xilinx Zynq-7000 All Programmable SoC, similar to ZC70x board but which has four different daughter cards, like XM010, XM011, XM012 and XM013 ZC770 XM012: - 1GB DDR3 - 64MiB Numonyx NOR flash - USB-UART Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Cc: Stefan Roese <sr@denx.de>
| * | zynq: Add zynq_zc770 xm013 board supportJagannadha Sutradharudu Teki2014-01-10-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZC770 is a complete development board based on the Xilinx Zynq-7000 All Programmable SoC, similar to ZC70x board but which has four different daughter cards, like XM010, XM011, XM012 and XM013 ZC770 XM013: - 1GB DDR3 - 128 Mb Quad-SPI Flash(dual parallel) - USB-UART Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add zynq_zc770 xm010 board supportJagannadha Sutradharudu Teki2014-01-10-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZC770 is a complete development board based on the Xilinx Zynq-7000 All Programmable SoC, similar to ZC70x board but which has four different daughter cards, like XM010, XM011, XM012 and XM013 ZC770 XM010: - 1Gb DDR3 - 1Mb SST SPI flash - 128 Mb Quad-SPI Flash - 8 Mb SST SI flash - Full size SD/MMC card cage - 10/100/1000 Ethernet - USB-UART Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add zynq microzed board supportJagannadha Sutradharudu Teki2014-01-10-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MicroZed is a low-cost development board based on the Xilinx Zynq-7000 All Programmable SoC. APSOC: - XC7Z010-1CLG400C Memory: - 1 GB of DDR3 SDRAM - 128Mb of QSPI flash(S25FL128SAGBHI200) - Micro SD card interface Communication: - 10/100/1000 Ethernet - USB 2.0 - USB-UART User I/O: - 100 User I/O (50 per connector) - Configurable as up to 48 LVDS pairs or 100 single-ended I/O Misc: - Xilinx PC4 JTAG configuration port - PS JTAG pins accessible via Pmod - 33.33 MHz oscillator - User LED and push switch For more info - http://zedboard.org/product/microzed Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: zc70x: Add Catalyst 24WC08 EEPROM config supportJagannadha Sutradharudu Teki2014-01-10-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | Adds configurations for Catalyst 24WC08 EEPROM, which is present on the zynq boards. Enable EEPROM support for zc70x boards. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq-common: Define exact TEXT_BASEJagannadha Sutradharudu Teki2014-01-10-1/+1
| | | | | | | | | | | | | | | | | | | | | Defined TEXT_BASE for u-boot starts from 0x4000000 w.r.t zynq memory-map. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Move CONFIG_SYS_SDRAM_SIZE to pre-board configsJagannadha Sutradharudu Teki2014-01-10-1/+4
| | | | | | | | | | | | | | | | | | | | | CONFIG_SYS_SDRAM_SIZE is specific to a board hence moved to specific pre-config board files. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add zynq zed board supportJagannadha Sutradharudu Teki2014-01-10-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zed is a complete development board based on the Xilinx Zynq-7000 All Programmable SoC. APSOC: - XC7Z020-CLG484-1 Memory: - 512 MB DDR3 - 256 Mb Quad-SPI Flash( - Full size SD/MMC card cage Connectivity: - 10/100/1000 Ethernet - USB OTG (Device/Host/OTG) - USB-UART Expansion: - FMC (Low Pin Count) - Pmod. headers (2x6) Video/Display: - HDMI output (1080p60 + audio) - VGA connector - 128 x 32 OLED - User LEDs (9) User inputs: - Slide switches (8) - Push button switches (7) Audio: - 24-bit stereo audio CODEC - Stereo line in/out - Headphone - Microphone input Analog: - Xilinx XADC header - Supports 4 analog inputs - 2 Differential / 4 Single-ended Debug: - On-board USB JTAG programming port - ARM Debug Access Port (DAP) For more info - http://zedboard.org/product/zedboard Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add zynq zc70x board supportJagannadha Sutradharudu Teki2014-01-10-9/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded processing includes ASIC and FPGA design. ZC702-: APSOC: - XC7Z020-CLG484-1 Memory: - DDR3 Component Memory 1GB - 16MB Quad SPI Flash - IIC - 1 KB EEPROM Connectivity: - Gigabit Ethernet GMII, RGMII and SGMII. - USB OTG - Host USB - IIC Bus Headers/HUB - 1 CAN with Wake on CAN - USB-UART Video/Display: - HDMI Video OUT - 8X LEDs Control & I/O: - 3 User Push Buttons - 2 User Switches - 8 User LEDs For more info on zc702 board: - http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm ZC706-: APSOC: - XC7Z045 FFG900 -2 AP SoC Memory: - DDR3 Component Memory 1GB (PS) - DDR3 SODIM Memory 1GB (PL) - 2X16MB Quad SPI Flash (dual parallel) - IIC - 1 KB EEPROM Connectivity: - PCIe Gen2x4 - SFP+ and SMA Pairs - GigE RGMII Ethernet (PS) - USB OTG 1 (PS) - Host USB - IIC Bus Headers/HUB (PS) - 1 CAN with Wake on CAN (PS) - USB-UART Video/Display: - HDMI 8 color RGB 4.4.4 1080P-60 OUT - HDMI IN 8 color RGB 4.4.4 Control & I/O: - 2 User Push Buttons/Dip Switch, 2 User LEDs - IIC access to GPIO - SDIO (SD Card slot) - 3 User Push Buttons, 2 User Switches, 8 User LEDs For more info on zc706 board: - http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq-common: Rename zynq with zynq-commonJagannadha Sutradharudu Teki2014-01-10-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | zynq.h -> zynq-common.h, zynq-common is Common configuration options for all Zynq boards. zynq.h is no longer exists hense removed from boards.cfg Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add GEM0, GEM1 configs supportJagannadha Sutradharudu Teki2014-01-10-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | Zynq ethernet controller support two GEM's like CONFIG_ZYNQ_GEM0 and CONFIG_ZYNQ_GEM1 enabled both so-that the respective board will define these macros based on their usage. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Add UART0, UART1 configs supportJagannadha Sutradharudu Teki2014-01-10-4/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | Zynq uart controller support two serial ports like CONFIG_ZYNQ_SERIAL_UART0 and CONFIG_ZYNQ_SERIAL_UART1 enabled both so-that the respective board will define these macros based on their usage. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Enable cache optionsJagannadha Sutradharudu Teki2014-01-10-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | - Enable cache command - Turn-off L2 cache - Turn-on D-cache Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Minor config cleanupJagannadha Sutradharudu Teki2014-01-10-37/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | Cleanups mostly on: - Add comments - Re-order configs - Remove #define CONFIG_ZYNQ_SDHCI Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Cleanup on memory configsJagannadha Sutradharudu Teki2014-01-10-13/+14
| | | | | | | | | | | | | | | | | | | | | | | | Cleanup on memory configuration options: - Add comment - Re-order configs Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Cleanup on miscellaneous configsJagannadha Sutradharudu Teki2014-01-10-9/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Cleanup on miscellaneous configurable options: - Rename SYS_PROMPT as "zynq-uboot" - Add comment - Re-order configs Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Enable Boot FreeBSD/vxWorksJagannadha Sutradharudu Teki2014-01-10-0/+7
| | | | | | | | | | | | | | | | | | This enabled Boot FreeBSD/vxWorks from an ELF image support Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | zynq: Enable CONFIG_FIT_VERBOSEJagannadha Sutradharudu Teki2014-01-10-0/+1
| | | | | | | | | | | | | | | | | | Enabled fit_format_{error,warning}() Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
| * | arm64: board support of vexpress_aemv8aDavid Feng2014-01-09-0/+189
| | | | | | | | | | | | | | | Signed-off-by: David Feng <fenghua@phytium.com.cn> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
| * | arm64: core supportDavid Feng2014-01-09-0/+1
| | | | | | | | | | | | | | | | | | | | | Relocation code based on a patch by Scott Wood, which is: Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Feng <fenghua@phytium.com.cn>
| * | add weak entry definitionDavid Feng2014-01-09-0/+4
| | | | | | | | | | | | Signed-off-by: David Feng <fenghua@phytium.com.cn>
| * | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-01-08-237/+7
| |\ \
| | * | arm: omap: cm_t35: enable gpio bank 5 clocks explicitlyNikita Kiryanov2014-01-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Following commit "arm: omap3: Enable clocks for peripherals only if they are used" (f33b9bd3984fb11e1d8566a866adc5957b1e1c9d) it is now necessary to enable clocks for GPIO banks explicitly. On cm_t35, GPIO bank 5 is necessary for scf0403 lcd support. Enable GPIO bank 5 clocks. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| | * | ARM: twister: add missing gpio clock initJeroen Hofstee2014-01-07-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit f33b9bd3984fb11e1d8566a866adc5957b1e1c9d breaks boards which do not explicitly enable the gpio clocks. This causes the twister spl to hang, since it uses the no longer enabled gpio 55. Add CONFIG_OMAP3_GPIO_2 to unbrick the board. Cc: Stefano Babic <sbabic@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | ARM: tam3517-common: fix nand spl bootJeroen Hofstee2014-01-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30, "mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme" removed CONFIG_SPL_NAND_SOFTECC from the tam3517 common config, causing the spl nand boot to fail. Add it back, so derived boards boot again. Cc: Pekon Gupta <pekon@ti.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Raphael Assenat <raph@8d.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Stefano Babic <sbabic@denx.de>
generated by cgit v1.1 at 2024-12-29 15:46:36 +0000