summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* ENGR00143442 uboot: support android spi boot and mfg on mx50 rd3 boardXinyu Chen2011-05-16-1/+345
| | | | | | | | | | | | Add mx50_rd3_android default config file Add basic support for UBI partition mount and UBIFS file read for recovery Add gpmi nand enable in MFG kernel commandline by uboot configure, which enable MFG tool to flash system images on NAND. The total NAND boot and NAND recovery has been disabled. They will be enabled later. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00142995 MX50: Enable uSDHC instead of eSDHC for SDR modeAnish Trivedi2011-05-10-7/+58
| | | | | | | | | | | | | | | | | | On SD3 on MX50, there is an option to choose eSDHC or uSDHC controller. By default eSDHC is selected. However, eSDHC shows some borderline timing in SDR mode at 50 MHz, whereas uSDHC shows borderline timing in DDR mode at 50 MHz. Therefore, add a compile time option to uboot for MX50 to select uSDHC in SDR mode or eSDHC in DDR mode on SD3 port. By default the compile time option, CONFIG_MX50_ENABLE_USDHC_SDR, is commented out in the include/configs/mx50_<board>.h file to select eSDHC with DDR mode enabled. Uncomment the define to select uSDHC with only SDR mode enabled. Also increased max frequency supported by ESDHC to 52 MHz instead of 50 MHz. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00143178 mx53 ARD DDR3 board: add MFG tool supportLily Zhang2011-05-10-0/+230
| | | | | | Add MFG tool support for MX53 ARD DDR3 board. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00142740 mx50 rdp: mfg support GPMI nand by command lineXinyu Chen2011-04-29-2/+2
| | | | | | | | As android make UBIFS as default file system on MX508 RDP, we must enable MFG tool to support UBIFS image update. So enable GPMI nand in default commandline to detect nand devices. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00141335-3: Add CONFIG_EMMC_DDR_PORT_DETECT to mx53 and mx50config filesTerry Lv2011-04-11-12/+41
| | | | | | | | | | | | Add CONFIG_EMMC_DDR_PORT_DETECT to mx53 and mx50 config files. For fastboot, please note that the bit width of card should match the dip settings. For example, if mmcinfo shows eMMC 4.4 card is 8Bit DDR, then dip settings should be 8bit DDR. Then fastboot can work. Otherwise, fastboot will fail. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141556: Fix copyright issueTerry Lv2011-04-08-24/+13
| | | | | | | | | | | We're following the following rules: 1. FSL copyright should be added for freescale added and modified files. 2. FSL copyright should go after existing copyrights. 3. For Duplicate FSL copyright, Our copyright will go after that also. 4. FSL copyright should not include personal names as part. 5. For only FSL copyright, "All rights reserved" is not mattered. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141363: change mx53 uart clk parent to pll2Jason Chen2011-03-31-13/+13
| | | | | | | | | | Change all mx53 platform uart clk default parent to pll2. MX53 SMD board need support LVDS and HDMI at the same time, they may use the same clock parent-pll4, so kernel need change ipu di clock parent to pll3, after that, uart clock parent need change to pll2 to avoid console mess. Signed-off-by: Jason Chen <b02280@freescale.com>
* ENGR00141157: Add m25p32 spi nor config to mx53_smd_androidTerry Lv2011-03-25-6/+18
| | | | | | Add m25p32 spi nor config to mx53_smd_android. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141129: Add m25p32 spi_nor support for mx53_smdTerry Lv2011-03-24-12/+44
| | | | | | Add m25p32 spi_nor support for mx53_smd. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00141058 MX50_RDP: Android Fix typo in recoevry command linerel_imx_2.6.35_11.03.00Zhang Jiejing2011-03-23-1/+1
| | | | | | | | | A typo is in last commit, will cause android recovery not work. Add a space between two string. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00141000 MX50_RDP: add android recovery support.Zhang Jiejing2011-03-23-1/+11
| | | | | | Add android recovery related config and code. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00140872 Add MX50 RD3 SupportRobby Cai2011-03-22-0/+533
| | | | | | | | Assembled With new PMIC chip - MC34708 (Ripley), and new SPI NOR - M25P32 as well. Add new config file for RD3. Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00140824 Android: Enable fastboot support for mx50 rdpSammy He2011-03-21-1/+328
| | | | | | Enable fastboot support for mx50 rdp. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00140825: Add mx53 to2.1 chip id recognitionTerry2011-03-20-0/+2
| | | | | | Add mx53 to2.1 chip id recognition. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00140486 Add SPI NOR Flash M25P32 driverRobby Cai2011-03-18-1/+16
| | | | | | | So far, it's supposed to be on MX50 RD3 and MX53 SMD Signed-off-by: Robby Cai <R63905@freescale.com> (cherry picked from commit 0e3d67cd1a2dc30af80e5119b626d997be254991)
* ENGR00140750 mx53smd: set the default DDR size to 512MB for android configureXinyu Chen2011-03-17-3/+2
| | | | | | | | Decrease the default DDR size to 512MB in the default android uboot configuration file. This can align with most customers' hardware design, and help us to find more issues before release. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00140692 Update for DDR3-based MX53 SABRE Auto boardsMahesh Mahadevan2011-03-16-0/+310
| | | | | | | Added a new config file, the DDR setup is similar to the MX53 Quick Start & MX53 SABRE-Tablet ref design boards. Signed-off-by: Mahesh Mahadevan <r9aadq@freescale.com>
* ENGR00140089 MX53_SMD: update command line.Zhang Jiejing2011-03-14-3/+3
| | | | | | | 1. update new style ldb per kernel update. 2. update the default boot command is from eMMC Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00139747: Read fuse to distinguish between mx53 revA and revBTerry Lv2011-03-02-0/+7
| | | | | | | | | Read fuse to distinguish between mx53 revA and revB. Now SoC efuse is used for board id. Thus we now check fuse value for board rev and id. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00139120: Correct CONFIG_CMD_MMC to CONFIG_CMD_IIM for iimTerry Lv2011-02-14-8/+8
| | | | | | Correct CONFIG_CMD_MMC to CONFIG_CMD_IIM for iim. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00138549 Android fastboot: Support eMMC4.4 on imx53_smdrel_imx_2.6.35_11.01.00Sammy He2011-01-28-4/+12
| | | | | | | | Support eMMC4.4 storage on imx53_smd android fastboot, using environment to control it, the command is: > setenv fastboot_dev mmc1 Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00118558 MX51/MX53: change the boot command of android boards.Zhang Jiejing2011-01-27-10/+14
| | | | | | | The android uImage is greater than 3M, so we need to change the boot command. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00138534 Disable splashimage support defaultly for PDKLiu Ying2011-01-26-3/+0
| | | | | | | Disable splashimage support defaultly for MX51 BBG/MX53 SMD/ MX53 ARD platforms. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138422-2 Add SATA storage support for android fastbootSammy He2011-01-26-3/+4
| | | | | | Add SATA storage support for android fastboot. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00138468-2 Enable splashimage support for several platformsLiu Ying2011-01-25-0/+3
| | | | | | | This patch enables splashimage support for MX53 SMD/ARD and MX51 BBG pdk platforms. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138390 android recovery, enlarge uImage sizeZhang Jiejing2011-01-24-2/+2
| | | | | | Kernel image is bigger than 3M, the 0x1800 will not enough. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00138240 Disable splashimage support for PDKLiu Ying2011-01-20-3/+0
| | | | | | | Disable splashimage support for mx53 smd, mx53 ard and mx51 bbg. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138191 disable the SPLASH SCREEN for androidXinyu Chen2011-01-19-2/+0
| | | | | | Disable for BBG and SMD Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00138040-2 MX51 BBG Android:Support splashimageLiu Ying2011-01-17-0/+19
| | | | | | This patch supports splashimage for MX51 BBG Android. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138040-1 MX53 SMD Android:Support splashimageLiu Ying2011-01-17-0/+23
| | | | | | This patch supports splashimage for MX53 SMD Android. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137894-6 MX53 SMD:Support splashimageLiu Ying2011-01-14-0/+23
| | | | | | | | | | | | | | This patch supports to use pwm wave to control backlight. The pwm rate is 20KHz and the pwm duty is 50%. Only lvds panel is supported. Use 'lvds_num' env variable to choose to use lvds0 or lvds1. However, only lvds1 is tested as the lvds cable cannot be plugged into lvds0 connector. Note that you need to add 'splashimage' env variable to set the memory address of the bmp image. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137894-5 MX53 ARD:Support splashimageLiu Ying2011-01-14-0/+23
| | | | | | | | | | | This patch supports to use pwm wave to control backlight. The pwm rate is 200Hz and the pwm duty is 50%. Use 'lvds_num' env variable to choose to use lvds0 or lvds1. Note that you need to add 'splashimage' env variable to set the memory address of the bmp image. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137894-3 IPU driver enhancementLiu Ying2011-01-14-4/+12
| | | | | | | | 1) Remove MX51 related comments in ipu drivers. 2) Add di clocks. 3) Support pixel clock being deprived from external clock. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137894-2 MX53: Add ipu base addr and ipu clockLiu Ying2011-01-13-0/+5
| | | | | | This patch adds ipu base address and ipu clock. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137894-1 Add imx pwm driver supportLiu Ying2011-01-13-0/+37
| | | | | | | This patch adds imx pwm driver support as a misc device. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137791 MX53: Update for MFG toolLily Zhang2011-01-11-1/+500
| | | | | | | | - Add MFG tool support for MX53 SMD and MX53 LOCO boards - Update mx53 ARD MFG defconfig to pass compile Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00137358: Add saving environment to sata device supportTerry Lv2011-01-11-4/+24
| | | | | | Add saving environment to sata device support. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00137603 Add mx53_smd_android config for androidSammy He2011-01-08-2/+328
| | | | | | Add mx53_smd_android config for android build. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00137604: Change PLL4 to 455MHz for mx53Terry Lv2011-01-07-1/+5
| | | | | | | Required by display to set ldb. We need to set PLL4 to 455MHz. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00137497-2 MX53: Add LOCO board supportLily Zhang2010-12-30-2/+273
| | | | | | | | | | | Add MX53 LOCO board support The following functions are tested in the board: - Micro SD boot - MMC/SD read/write. - clk command - fuse command Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00137497-1 Import new mach-type header fileLily Zhang2010-12-30-33/+2387
| | | | | | | | Import new mach-type header file for MX53 LOCO board Signed-off-by: Lily Zhang <r58066@freescale.com> Acked-by: Lily Zhang <r58066@freescale.com>
* ENGR00136075 MX53: Add SMD board supportLily Zhang2010-12-30-0/+291
| | | | | | | | | | | | | | | | | | | | | | | Add MX53 SMD support: - Use DDR3 script for SMD board from Mike Kjar: "Rita_init_LCB_CMOS.inc" - Set the default CPU core frequency as 1GHZ. The following functions are tested on SMD board: - SD/MMC boot, read, write via SDHC1 - eMMC4.4 boot, read, write via SDHC3. - SATA boot, read, write. To support SATA boot via internal clock, please ensure the fuse "SATA_ALT_CLK_REF" was blown. - FEC - UART - clk command - iim command Signed-off-by: Liu Ying <b17645@freescale.com> Signed-off-by: Jason Chen <b02280@freescale.com> Signed-off-by: Terry Lv <r65388@freescale.com> Signed-off-by: Anish Trivedi <anish@freescale.com> Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00136863-1: Change mmc framework architecture.Terry Lv2010-12-29-0/+3
| | | | | | | | | | Change mmc framework architecture. Mainly for code clean and restructure. Mainly merge our code with community code. Based on commit 17b4c8e9eb30e3eb305baef98eb23325e61db592. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00137408: Add FAT32 supportTerry Lv2010-12-29-34/+33
| | | | | | | | Add FAT32 support. The code is got from community. Based on hash number 71aab09b2c1edd1b6e00819abd1e31c04db04f36. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00137372 MX53: Switch back to use DCD and update DDR scriptsLily Zhang2010-12-28-576/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. This patch is used to switch back to use DCD for flash header instead of plug-in. This change request is due to the following reasons: 1) U-boot community doesn't accept current plug-in solution when upstreaming. 2) Plug-in isn't supported by MX53 ROM serial download mode. No effective workaround is found now. To use the same code base to support normal U-Boot and MFG tool better, adopt DCD solution firstly. 3) Current MX53 DDR scripts don't exceed the length limitation of DCD. For MX53 TO2.0 EVK/ARM2 board, raise DDR frequency to 400MHZ after VCC and VDDA voltages are raised as 1.3V. Since ARM2 CPU2 board share the same script with EVK, delete ARM2 CPU2 config files. ARM2 CPU2 board can share the same bootloader with EVK. 2. Update MX53 DDR2 scripts for TO1.0/TO2.0 EVK/ARD/ARM2 boards The script "MX53_TO2_DDR2_EVK_ARD.inc" is located under http://compass.freescale.net/livelink/livelink? func=ll&objId=221058910&objAction=browse&viewType=1 This script is published by ATX and FIL team on Dec 16th, 2010 3. Update MX53 ARM2 CPU3 DDR3 script "MX53_TO2_DDR3_CPU3.inc" under the same compass folder Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00137273 uboot: update the android default env for 2.6.35 kernelXinyu Chen2010-12-22-8/+8
| | | | | | | Change the ramdisk load address to loadaddr + 0x400000. Add gpu_memory= kernel parameter. Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
* ENGR00137214 MX50: Turn on ZQ calib config by default and fix hang problemRobby Cai2010-12-21-4/+0
| | | | | | | | 1) Turn on ZQ calib config by default in uboot. 2) Remove one problematic statement which can cause hang issue 3) Change comment style from ; to // Signed-off-by: Robby Cai <R63905@freescale.com>
* ENGR00134068 MX51 BBG:Support CLAA WVGA splashimageLiu Ying2010-12-16-0/+21
| | | | | | | | | | | 1) IOMUX/backlight support for CLAA WVGA LCD panel. 2) Add video mode for CLAA WVGA LCD panel. 3) Support IPU di1 interface for framebuffer. 4) Enhance IPU driver. 5) Add freescale 600x400 8BPP BMP logo. Signed-off-by: Terry Lv <R65388@freescale.com> Signed-off-by: Liu Ying <b17645@freescale.com>
* ENGR00136038: Remove config CONFIG_EMMC_DDR_MODETerry Lv2010-12-10-2/+4
| | | | | | | | | 1. As we can check DDR dynamically, remove CONFIG_EMMC_DDR_MODE in mmc.c. 2. Add config CONFIG_EMMC_DDR_PORT_DETECT config for some boards that only some board support DDR. Signed-off-by: Terry Lv <r65388@freescale.com>
* MX51: Add video supportStefano Babic2010-12-10-0/+68
| | | | | | | | | | | | | | Add framebuffer driver for the MX51 processor working on the IPUv3 internal graphic processor. The port is based on the driver found in the kernel delivered by Freescale as part of i.MX BSP: [kernel 2.6.31 commit cc4fe714041805997b601fe8e5dd585d8a99297f] [agust@denx.de: some style fixes and dead code removal] Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de> (cherry picked from commit 5dda7945d18077db81eb0cfdc2f9d4525e6b77b1)
generated by cgit v1.1 at 2024-12-30 07:56:42 +0000