summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* arm/km: trigger reconfiguration for the Xilinx FPGAHolger Brunck2011-11-03-0/+3
| | | | | | | | | | The Xilinx FPGA must be reconfigured each time the unit reboots. The FPGA is connected to the GPIO pin 39 from kirkwood. This patch triggers this pin for km_kirkwood_pci targets. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: add boardid and hwkey to kernel command lineHolger Brunck2011-11-03-1/+2
| | | | | | | | | | We need in some cases a possibility for the kernel to distinguish on which board he is running. On powerpc we did this with different dts files. On arm currently we can't do this, so add boardid and hwkey to the kernel command line and use it later on in the kernel code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boardsValentin Longchamp2011-11-03-0/+5
| | | | | | | | | | | | | | We got dropped from Linux mach-types.h because of a lack of mainline support and this is needed since the last Linux/u-boot mach-types synchro. This patch also defines CONFIG_MACH_TYPE for all keymile boards, as this is a mandatory CONFIG for ARM boards now. The initialization of gd->bd->bi_arch_number is removed form km_arm.c, our board file. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* netspace_v2: enable I2C EEPROM supportSimon Guinot2011-11-03-0/+11
| | | | | | | | An I2C EEPROM HT24LC04 (512B) is available on the netspace_v2 board (and parents). This EEPROM hold data such as Ethernet MAC addresses and power flags. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
* netspace_v2: fix SDRAM configurationSimon Guinot2011-11-03-1/+6
| | | | | | | | | | | | Network Space (Max) v2 and Internet Space v2 boards have different SDRAM configuration and size: respectively 256MB (DDR2 1Gb, 128Mbx8 organisation) and 128MB (DDR2 512Mb, 64Mbx8 organisation). To handle the differences, this patch add a dedicated kwimage.cfg file for Internet Space v2. Additionnaly the number of SDRAM banks is fixed. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
* arm/km: add variable waitforne to mgcoge3unHolger Brunck2011-11-03-0/+2
| | | | | | | | | Add this board specific variable to the default environment of this board. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclaredAjay Bhargav2011-11-03-1/+11
| | | | | | | | This patch fix the build failure (error: 'MACH_TYPE_SHEEVAD' undeclared (first use in this function)) for gplugD due to recent sync of mach-types.h with its linux original. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* am335x: Temporarily add MACH_TYPE defineTom Rini2011-11-03-0/+1
| | | | | | This is registered and can be removed at the next sync up. Signed-off-by: Tom Rini <trini@ti.com>
* misc:pmic:samsung Enable PMIC driver at C210 Universal targetŁukasz Majewski2011-11-03-0/+17
| | | | | | | | Enable support for PMIC driver at C210 Universal reference target. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 targetŁukasz Majewski2011-11-03-0/+2
| | | | | | | | | Define the D-cache line size for S5PC210 UNIVERSAL reference target. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Anton Staaf <robotboy@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI targetŁukasz Majewski2011-11-03-0/+2
| | | | | | | | | Define the D-cache line size for S5PC110 GONI reference target. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Anton Staaf <robotboy@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* smdkv310: use macro for mmc data read function addressChander Kashyap2011-11-03-0/+1
| | | | | | | | | | board/samsung/smdkv310/mmc_boot.c: Removed the typedef for "mmc data read API (copy_sd_mmc_to_mem)" as it is used only once and replaced hard-coded API address value by macro. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* smdkv310: use spl framework for mmc splChander Kashyap2011-11-03-1/+3
| | | | | | | | smdkv310 board was using mmc_spl framework for mmc spl support. This patch migrates the framework from mmc_spl to spl. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SMDKV310: Initialize board id using CONFIG_MACH_TYPEChander Kashyap2011-11-03-0/+3
| | | | | | | Use CONFIG_MACH_TYPE generic macro to initialize board id. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* ORIGEN : enable device tree supportAngus Ainslie2011-11-03-0/+3
| | | | | | | | Enable passing a flattened device tree to the kernel. Signed-off-by: Angus Ainslie <angus.ainslie@linaro.org> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* MX25: tx25: Fix building due to missing MACH_TYPEStefano Babic2011-11-03-0/+6
| | | | | | | | Added MACH_TYPE for the tx25 to the configuration file. The MACH_TYPE is dropped from mach-types.h after last sync with kernel. Signed-off-by: Stefano Babic <sbabic@denx.de>
* mx31: Add board support for HALE TT-01Helmut Raiger2011-11-03-0/+254
| | | | | | | | | This adds basic board support for TT-01 based on the Bluetechnix i.MX31 SOM. Currently only NOR-Flash boot is implemented. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
* MX35: add support for flea3 boardStefano Babic2011-11-03-0/+286
| | | | | | | | The flea3 board is a custom board by CarMediaLab used in automotive. Network (FEC), NOR, NAND and SPI are supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX51: vision2: add MACH_TYPE in config fileStefano Babic2011-11-03-0/+3
| | | | | | | | Add the MACH type to the configuration file. Maybe the board will be not pushed into linux ML, but it remains compatible with older kernels. Signed-off-by: Stefano Babic <sbabic@denx.de>
* mx51evk: Remove unused get_board_rev functionFabio Estevam2011-11-03-1/+0
| | | | | | No board information is passed for MX51EVK, so remove get_board_rev function. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx51evk: Remove unneeded '1' from mx51evk.hFabio Estevam2011-11-03-5/+5
| | | | | | Remove unneeded '1' from mx51evk.h. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx35pdk: Add RTC supportFabio Estevam2011-11-03-0/+2
| | | | | | | | MX35PDK has an MC13892 PMIC. Add RTC support. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de>
* mx51evk: Add RTC supportFabio Estevam2011-11-03-0/+3
| | | | | | | | | | | MX51EVK has a MC13892 PMIC. Add RTC support. Tested via 'date' command that reads the PMIC RTC registers: MX51EVK U-Boot > date Date: 1970-01-01 (Thursday) Time: 0:40:35 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* rtc: Make mc13783-rtc driver genericFabio Estevam2011-11-03-6/+6
| | | | | | | | | | | | | | | | | Rename mc13783-rtc so that it can be used for both MC13783 and MC13892 PMICs. efikamx board, for example, does use a MC13892 PMIC, but the RTC selection is currently made as: #define CONFIG_RTC_MC13783 ,which is not very obvious. Let the MC13783 and MC13892 RTC be selected by: #define CONFIG_RTC_MC13XXX Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* qong: remove unneeded "1" from qong.hFabio Estevam2011-11-03-17/+17
| | | | | | Remove unneeded "1" from qong.h. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIMEWolfgang Grandegger2011-11-03-5/+5
| | | | | Signed-off-by: Wolfgang Grandegger <wg@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* sandbox: put stdin into raw modeMike Frysinger2011-11-03-0/+5
| | | | | | | | This allows us to act like a serial device: we get tab chars and CTRL+C and respond appropriately. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Simon Glass <sjg@chromium.org>
* sandbox/tegra2: fix typo in autocomplete defineMike Frysinger2011-11-03-2/+2
| | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Simon Glass <sjg@chromium.org>
* mmc: sdhci: add mmc structure for hostLei Wen2011-11-03-0/+3
| | | | | | | So that sdhci host would tell in the driver that the mmc current attributes. Signed-off-by: Lei Wen <leiwen@marvell.com>
* mmc: sdhci: fix build warningLei Wen2011-11-03-0/+3
| | | | | | | | | | | | | | | | | | | | | | If CONFIG_MMC_SDHCI_IO_ACCESSORS is defined, the following warning would shows up: include/sdhci.h:224: warning: 'struct sdhci_host' declared inside parameter list include/sdhci.h:224: warning: its scope is only this definition or declaration, which is probably not what you want include/sdhci.h:225: warning: 'struct sdhci_host' declared inside parameter list include/sdhci.h:226: warning: 'struct sdhci_host' declared inside parameter list include/sdhci.h:227: warning: 'struct sdhci_host' declared inside parameter list include/sdhci.h:228: warning: 'struct sdhci_host' declared inside parameter list include/sdhci.h:229: warning: 'struct sdhci_host' declared inside parameter list Signed-off-by: Lei Wen <leiwen@marvell.com>
* mmc: change magic number to macro defineLei Wen2011-11-03-7/+9
| | | | | | | | Previous magic number is hard to parse its meaning, change it to respective macro definition Signed-off-by: Lei Wen <leiwen@marvell.com> Acked-by: WOlfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-10-28-56/+647
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: ARM: Add Calxeda Highbank platform dkb: make mmc command as default enabled Marvell: dkb: add mmc support ARM: pantheon: add mmc definition davinci: remove config.mk file from the sources ARM:AM33XX: Add support for TI AM335X EVM ARM:AM33XX: Added timer support ARM:AM33XX: Add emif/ddr support ARM:AM33XX: Add clock definitions ARM:AM33XX: Added support for AM33xx omap3/emif4: fix registers definition davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM davinci: emac: add support for more than 1 PHYs davinci: emac: add new features to autonegotiate for EMAC da850evm: Move LPSC configuration to board_early_init_f() omap4_panda: Build in cmd_gpio support on panda omap: Don't use gpio_free to change direction to input mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset OMAP3: overo : Add environment variable optargs to bootargs OMAP3: overo: Move ethernet CS4 configuration to execute based on board id OMAP3: overo : Use ttyO2 instead of ttyS2. da830: add support for NAND boot mode dm36x: revert cache disable patch dm644X: revert cache disable patch devkit8000: Add malloc space omap: spl: fix build break due to changes in FAT OMAP3 SPL: Provide weak omap_rev_string omap: beagle: Use ubifs instead of jffs2 for nand boot omap: overo: Disable pull-ups on camera PCLK, HS and VS signals omap: overo: Configure mux for gpio10 SPL: Add DMA library omap3: Add interface for omap3 DMA omap3: Add DMA register accessors omap3: Add Base register for DMA arm, davinci: add missing LSPC define for MMC/SD1 U-Boot/SPL: omap4: Make ddr pre-calculated timings as default. DaVinci: correct MDSTAT.STATE mask omap4: splitting padconfs into common, 4430 and 4460 omap4: adding revision detection for 4460 ES1.1 omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL gplug: fixed build error as a result of code cleanup patch kirkwood_spi: add dummy spi_init() gpio: mvmfp: reduce include platform file ARM: orion5x: reduce dependence of including platform file serial: reduce include platform file for marvell chip ARM: kirkwood: reduce dependence of including platform file ARM: armada100: reduce dependence of including platform file ARM: pantheon: reduce dependence of including platform file Armada100: Add env storage support for Marvell gplugD Armada100: Add SPI flash support for Marvell gplugD Armada100: Add SPI support for Marvell gplugD SPI: Add SPI driver support for Marvell Armada100 dreamplug: initial board support. imx: fix coding style misc: pmic: drop old Freescale's pmic driver MX31: mx31pdk: use new pmic driver MX31: mx31ads: use new pmic driver MX31: mx31_litekit: use new pmic driver MX5: mx53evk: use new pmic driver MX5: mx51evk: use new pmic driver MX35: mx35pdk: use new pmic driver misc: pmic: addI2C support to pmic_fsl driver misc: pmic: use I2C_SET_BUS in pmic I2C MX5: efikamx/efikasb: use new pmic driver MX3: qong: use new pmic driver RTC: Switch mc13783 to generic pmic code MX5: vision2: use new pmic driver misc: pmic: Freescale PMIC switches to generic PMIC driver misc:pmic:samsung Enable PMIC driver at GONI target misc:pmic:max8998 MAX8998 support at a new PMIC driver. misc:pmic:core New generic PMIC driver mx31pdk: Remove unneeded config mx31: provide readable WEIM CS accessor MX51: vision2: Set global macros I2C: Add i2c_get/set_speed() to mxc_i2c.c ARM: Update mach-types devkit8000: Add config to enable SPL MMC boot devkit8000: protect board_mmc_init arm, post: add missing post_time_ms for arm cosmetic, post: Codingstyle cleanup arm, logbuffer: make it compileclean tegra2: Enable MMC for Seaboard tegra2: Add more pinmux functions tegra2: Rename PIN_ to PINGRP_ tegra2: Add more clock functions tegra2: Clean up board code a little tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
| * ARM: Add Calxeda Highbank platformRob Herring2011-10-27-0/+113
| | | | | | | | | | | | | | | | | | Add basic support for Calxeda Highbank platform. Only minimal support with serial and SATA are included. Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * dkb: make mmc command as default enabledLei Wen2011-10-27-0/+1
| | | | | | | | Signed-off-by: Lei Wen <leiwen@marvell.com>
| * ARM:AM33XX: Add support for TI AM335X EVMChandan Nath2011-10-27-0/+122
| | | | | | | | | | | | | | | | | | This patch adds basic support for booting the board. This patch adds support for the UART necessary to get to the u-boot prompt. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUMManjunath Hadli2011-10-27-10/+0
| | | | | | | | | | | | | | | | | | remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM as they are no longer needed with the support for more than 1 PHYs in davinci emac driver. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * da850evm: Move LPSC configuration to board_early_init_f()Christian Riesch2011-10-27-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit f1d2b313c9eb6808d30c16a9eb5251240452a56c the serial port of the da850evm is accessed before the UART2 peripheral of the SoC is powered on in the function board_init() in board/davinci/da8xxevm/da850evm.c. When u-boot is used in conjunction with the UBL (user boot loader, see doc/README.davinci) on this board, the UART2 peripheral is already turned on by UBL at the time u-boot is started. Hence, the wrong initialization sequence is not noticed by most users. However, if UBL is not used, u-boot must power on the peripheral before using it. This patch adds a board_early_init_f() function for the LPSC configuration to the da850evm board configuration. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * omap4_panda: Build in cmd_gpio support on pandaJoe Hershberger2011-10-27-0/+3
| | | | | | | | | | | | | | | | | | Enable the gpio command Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * OMAP3: overo : Add environment variable optargs to bootargsPhilip Balister2011-10-27-0/+3
| | | | | | | | | | | | | | | | | | | | This allows the user can easily add extra kernel arguments. Very helpful for reserving memory for the DSP without rewriting the entire kernel argument line. Signed-off-by: Philip Balister <philip@opensdr.com> Tested-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * OMAP3: overo : Use ttyO2 instead of ttyS2.Philip Balister2011-10-27-1/+1
| | | | | | | | | | | | | | | | | | Starting with kernel 2.6.37, the serial ports on the OMAP3 are called ttyOX, not ttySX. Signed-off-by: Philip Balister <philip@opensdr.com> Tested-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * da830: add support for NAND boot modeManjunath Hadli2011-10-27-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | Add support for enabling NAND boot mode in configuration file and add correspanding pinmux support, nand initialize function in board file. The size required for environment variables not more than 10KB the CONFIG_ENV_SIZE is set to 10KB from (512 << 10). Acked-by: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * dm36x: revert cache disable patchManjunath Hadli2011-10-27-3/+0
| | | | | | | | | | | | | | | | | | | | | | revert commit 98c19aff9524e1d0dd6bf39bf7bde5644f121feb as the disabling of cache need not be done explicitly. Subsequent patches to new cache management framework has fixed it. EMAC issue with cache coherency still exists when cahces are enabled. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * dm644X: revert cache disable patchManjunath Hadli2011-10-27-3/+0
| | | | | | | | | | | | | | | | | | | | | | revert commit 913a39e9aa4d935948d41cd727d53f5878414a77 as the disabling of cache need not be done explicitly. Subsequent patches to new cache management framework has fixed it. EMAC issue with cache coherency still exists when cahces are enabled. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * devkit8000: Add malloc spaceTom Rini2011-10-27-0/+3
| | | | | | | | | | | | | | | | | | With malloc support being a new requirement for all ARM SPL implementations, define a small area for use on devkit8000. Cc: Frederik Kriewitz <frederik@kriewitz.eu> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * omap: spl: fix build break due to changes in FATAneesh V2011-10-27-8/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | FAT library now uses malloc() and free(). But SPL doesn't have heap until now. Setup a heap in SDRAM to fix this issue. However this increases SPL footprint beyond the available SRAM budget. So, compile out some fancy features in the SDARM init bring back footprint under control CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * omap: beagle: Use ubifs instead of jffs2 for nand bootSteve Sakoman2011-10-27-2/+2
| | | | | | | | | | | | Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Koen Kooi <k-kooi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.SRICHARAN R2011-10-27-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | All ddr configurations(geometry/timings) are done automatically by detecting the device connected at run time. Though this is a useful feature, making this as a default setting increases the code size by about 2K bytes. This is quite big, especially in the case of SPL which runs from a smaller SRAM. So do not use this feature as the default setting, instead use the precalculated tables. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARM: orion5x: reduce dependence of including platform fileLei Wen2011-10-27-0/+1
| | | | | | | | | | | | | | | | | | | | | | For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Signed-off-by: Lei Wen <leiwen@marvell.com>
| * Armada100: Add env storage support for Marvell gplugDAjay Bhargav2011-10-27-2/+8
| | | | | | | | | | | | | | This patch adds support for envrionment varaible storage in SPI flash for Marvell gplugD. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
| * Armada100: Add SPI flash support for Marvell gplugDAjay Bhargav2011-10-27-0/+4
| | | | | | | | | | | | | | This patch enables Atmel AT45 SPI flash support for Marvell gplugD Enables SF commands. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
generated by cgit v1.1 at 2024-11-19 22:42:32 +0000