summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* powerpc/85xx: Add support for new P102x/P2020 RDB style boardsLi Yang2011-09-29-0/+984
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following boards share a common design but with minor variations between them: P1020MSBG-PC P1020RDB-PC P1020UTM-PC P1021RDB-PC P1024RDB P1025RDB P2020RDB-PC The P1020RDB-PC shares its roots in the existing P1020RDB board design, however uses DDR3 instead of DDR2. P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK. Key features on these boards include: * DDR3 * NOR flash * NAND flash (on RDB's only) * SPI flash (on RDB's only) * SDHC/MMC card slot * VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB) * PCIE slot and mini-PCIE slots As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM is used to store SPD data. In case of absent or corrupted SPD, falling back to timing data embedded in the source code will be used. Raw timing data is extracted from DDR chip datasheet. Different speeds of DDR are supported with this approach. ODT option is forced to fit this set of boards, again because they don't have regular DIMMs. CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification for writing timing. VSC firmware Address is defined by default in config file for eTSEC1. SD width is based off DIP switch. DIP switch is detected on the board by reading i2c bus and setting the appropriate mux values. Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have pins multiplexing. QE function needs to be disabled to access Nor Flash and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe" in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below 'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD. 'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Zhao Chenhui <b26998@freescale.com> Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Tang Yuantian <b29983@freescale.com> Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
* powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macrosTimur Tabi2011-09-29-277/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS. This is necessary for the assembly-language code that relocates CCSR, since the assembler does not understand 64-bit constants. CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it should not be defined in a board header file. Similarly, CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so it should also not be defined in the board header file. CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT, and so CCSR will not be relocated. Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot builds (e.g. NAND) are required to relocate CCSR only during the last stage (i.e. the "real" U-Boot). All other stages should define CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated. README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ARM: remove broken "ixdp425" and "ixpdg425" boardsAlbert ARIBAUD2011-09-27-524/+0
| | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Stefan Roese <sr@denx.de>
* Minor Coding Style CleanupWolfgang Denk2011-09-22-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Drop bogus BOOTFLAG_* definitionsWolfgang Denk2011-09-20-11/+0
| | | | | | | | | | There is no code anywhere that references BOOTFLAG_* so remove these defines. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Peter Tyser <ptyser@xes-inc.com>
* DA830: Fix Build WarningSandeep Paulraj2011-09-13-1/+2
| | | | | | This commit fixes a build warning in the DA830 EVM build Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* led: remove camel casing of led identifiers globallyJason Kridner2011-09-13-16/+16
| | | | | | | | | | | | | | | Result of running the following command to address Wolfgang's comment about camel case: for file in `find . | grep '\.[chS]$'`; do perl -i -pe 's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done Discussion: http://patchwork.ozlabs.org/patch/84988/ Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: factor out common part from board config headersAneesh V2011-09-13-476/+288
| | | | | | | | Factor out common parts from omap4_sdp4430.h and omap4_panda.h into a new file omap4_common.h Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3 Beagle: Minor config cleanupSandeep Paulraj2011-09-12-1/+0
| | | | | | This patch removes a hardcoded MAC address Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da830: modify the MEMTEST start and end addressNagabhushana Netagunte2011-09-12-4/+4
| | | | | | | | | | Modify the MEMTEST start and end address. The memtest range was overlapping the CONFIG_SYS_LOAD_ADDR which causes the uImage to be corrupt.Also, modify the size for which mtest is run to 32MB from 16MB. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da830: enable SPI flash boot modeNagabhushana Netagunte2011-09-12-3/+4
| | | | | | | | | | | Enable SPI flash boot mode in configuration file as default. With the introduction of 456MHz part, SPI operating frequency will increase and at this frequency SPI does not work correctly. Hence reduce the default SPI speed to 30MHz from 50MHz. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da830: modify the U-Boot prompt stringNagabhushana Netagunte2011-09-12-1/+1
| | | | | | | | | | Modify U-boot promt string from 'DA830-evm >' to 'U-Boot >' as there are many variants of da830 based boards which have diffrent names such as L137, AM1707 etc. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* MX25: tx25: Cleanup tx25.h configFabio Estevam2011-09-12-8/+6
| | | | | | Cleanup tx25.h by removing unnecessary defines and by removing unneeded "1"'s. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX25: tx25: Fix build by making use of GPIO frameworkFabio Estevam2011-09-12-0/+2
| | | | | | | | | | | | | | | | | | | | | | Make use of GPIO framework and avoid the following build error: tx25.c: In function 'tx25_fec_init': tx25.c:73: error: dereferencing pointer to incomplete type tx25.c:74: error: dereferencing pointer to incomplete type tx25.c:75: error: dereferencing pointer to incomplete type tx25.c:76: error: dereferencing pointer to incomplete type tx25.c:83: error: dereferencing pointer to incomplete type tx25.c:84: error: dereferencing pointer to incomplete type tx25.c:114: error: dereferencing pointer to incomplete type tx25.c:115: error: dereferencing pointer to incomplete type tx25.c:116: error: dereferencing pointer to incomplete type tx25.c:117: error: dereferencing pointer to incomplete type tx25.c:124: error: dereferencing pointer to incomplete type tx25.c:125: error: dereferencing pointer to incomplete type tx25.c:126: error: dereferencing pointer to incomplete type Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* omap3: beagle: Fix build warningSanjeev Premi2011-09-12-1/+1
| | | | | | | | | | | | This patch fixes the warning dure to recent changes to the board configuration: cmd_i2c.o cmd_i2c.c -c cmd_i2c.c:109:1: warning: missing braces around initializer cmd_i2c.c:109:1: warning: (near initialization for 'i2c_no_probes[0]') Signed-off-by: Sanjeev Premi <premi@ti.com> Cc: Jason Kridner <jkridner@beagleboard.org> Acked-by: Jason Kridner <jdk@ti.com>
* Minor coding style cleanup.Wolfgang Denk2011-09-11-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* cm4008, cm41xx: fix build warningsWolfgang Denk2011-09-10-9/+9
| | | | | | | | | | | | | | Fix these: cm4008.c: In function 'board_eth_init': cm4008.c:79: warning: implicit declaration of function 'ks8695_eth_initialize' cm41xx.c: In function 'board_eth_init': cm41xx.c:79: warning: implicit declaration of function 'ks8695_eth_initialize' While we are at it, sort include list in netdev.h Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Greg Ungerer <greg.ungerer@opengear.com>
* KS8695: convert KS8695 eth driver to CONFIG_MULTI_ETHGreg Ungerer2011-09-10-0/+3
| | | | | | | Trivial conversion of the ks8695eth driver to a CONFIG_MULTI_ETH type driver. Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
* Fix warning: "assert" redefinedWolfgang Denk2011-09-10-2/+0
| | | | | | | | | | | | | | | | | | Commit 21726a7 "Add assert() for debug assertions" caused build warnings for many systems: In file included from bedbug.c:6: /home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined In file included from bedbug.c:3: /home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition In file included from cmd_bedbug.c:10: /home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined In file included from cmd_bedbug.c:5: /home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
* CM4000: fix missing RAM definitions for OpenGear boardsGreg Ungerer2011-09-10-0/+6
| | | | | | | | | | | | | | | | | The OpenGear boards CM4008, CM4116 and CM4148 need their DRAM base and RAM stack base addresses defined. Fixes: board.c: In function ‘__dram_init_banksize’: board.c:227: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function) board.c:227: error: (Each undeclared identifier is reported only once board.c:227: error: for each function it appears in.) board.c: In function ‘board_init_f’: board.c:270: error: ‘CONFIG_SYS_INIT_SP_ADDR’ undeclared (first use in this function) board.c:303: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function) Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
* Add assert() for debug assertionsSimon Glass2011-09-10-8/+21
| | | | | | | | | | | | | | | assert() is like BUG_ON() but compiles to nothing unless DEBUG is defined. This is useful when a condition is an error but a board reset is unlikely to fix it, so it is better to soldier on in hope. Assertion failures should be caught during development/test. It turns out that assert() is defined separately in a few places in U-Boot with various meanings. This patch cleans up some of these. Build errors exposed by this change (and defining DEBUG) are also fixed in this patch. Signed-off-by: Simon Glass <sjg@chromium.org>
* MX31: mx31pdk: make use of GPIO frameworkStefano Babic2011-09-07-0/+1
| | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* common: fix behavior of ROUND macro when input is already roundedAnton Staaf2011-09-07-1/+1
| | | | | | | | | | | | | | | | | | | Currently when you call ROUND with a value that is already a multiple of the second parameter it will return a value that is one multiple larger, instead of returning the value passed in. There are only two types of usage of ROUND currently, one in various config files to round CONFIG_SYS_MALLOC_LEN to a multiple of 4096 bytes. The other in cmd_sf.c where the incorrect behavior of ROUND is worked around be subtracting one from the length argument before passing it to ROUND. This patch fixes ROUND and removes the workaround from cmd_sf. It also results in all of the malloc pools that use ROUND to compute their size shrinking by 4KB. Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk2011-09-07-0/+245
|\ | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mmc: ftsdc010: add support of ftsdc010 mmc controller mmc: Fix mmc_send_status()
| * ftsdc010: add support of ftsdc010 mmc controllerMacpaul Lin2011-09-04-0/+245
| | | | | | | | | | | | Faraday FTSDC010 controller is a SD/MMC controller for SoC chip. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* | ARM: PXA: remove broken "zylonite" board.Wolfgang Denk2011-09-07-238/+0
| | | | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Marek Vasut <marek.vasut@gmail.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* | ARM: remove broken "shannon" board.Wolfgang Denk2011-09-07-223/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Rolf Offermanns <rof@sysgo.de>
* | ARM: remove broken "modnet50" board.Wolfgang Denk2011-09-07-196/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Thomas Elste <info@elste.org>
* | ARM: remove broken "lpc2292sodimm" board.Wolfgang Denk2011-09-07-159/+0
| | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | ARM: remove broken "lart" board.Wolfgang Denk2011-09-07-160/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Alex Züpke <azu@sysgo.de>
* | ARM: remove broken "impa7" board.Wolfgang Denk2011-09-07-174/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Marius Gröger <mag@sysgo.de>
* | ARM: remove broken "gcplus" board.Wolfgang Denk2011-09-07-185/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: George G. Davis <gdavis@mvista.com>
* | ARM: remove broken "evb4510" board.Wolfgang Denk2011-09-07-180/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Curt Brune <curt@cucy.com>
* | ARM: remove broken "ep7312" board.Wolfgang Denk2011-09-07-173/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Marius Gröger <mag@sysgo.de>
* | ARM: remove broken "dnp1110" board.Wolfgang Denk2011-09-07-162/+0
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Alex Züpke <azu@sysgo.de>
* | ARM: remove broken "SMN42" board.Wolfgang Denk2011-09-07-201/+0
| | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | FPGA: constify Lattice FPGA codeWolfgang Denk2011-09-05-2/+2
|/ | | | | | | | | | | | | The Lattice code was missed by commit e6a857d "fpga: constify to fix build warning" resulting in such warnings: fpga.c: In function 'fpga_load': fpga.c:238: warning: passing argument 2 of 'lattice_load' discards qualifiers from pointer target type fpga.c: In function 'fpga_dump': fpga.c:278: warning: passing argument 2 of 'lattice_dump' discards qualifiers from pointer target type Signed-off-by: Wolfgang Denk <wd@denx.de> cc: Stefano Babic <sbabic@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-coldfireWolfgang Denk2011-09-04-24/+39
|\ | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-coldfire: ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage ColdFire:Add mb for 5253 dram initialization ColdFire:Define the DM9000 byteswap for M5253 board. ColdFire:Update the env settings for several boards. ColdFire:disable the NFS define for 52277 board. ColdFire:Update the timer_init since it was unified. ColdFire: Cleanup for partial linking and --gc-sections ColdFire: Update compile flags for each CPUs ColdFire:Fix the configuration broken for some boards.
| * ColdFire:Define the DM9000 byteswap for M5253 board.Jason Jin2011-09-04-0/+1
| | | | | | | | | | | | | | | | The M5253DEMO board swapped the io pins which make the standard IO function did not work for dm9000. Define the byte swap to use raw io for dm9000. Signed-off-by: Jason Jin <Jason.jin@freescale.com>
| * ColdFire:Update the env settings for several boards.Jason Jin2011-09-04-24/+37
| | | | | | | | | | | | | | Move the environment outside the u-boot for some boards and enlarge the u-boot size in some env settings. Signed-off-by: Jason Jin <Jason.jin@freescale.com>
| * ColdFire:disable the NFS define for 52277 board.Jason Jin2011-09-04-0/+1
| | | | | | | | | | | | | | There is no network device on ColdFire 52277EVB board.But the default cmd include NFS define which make the build error. Signed-off-by: Jason Jin <Jason.jin@freescale.com>
* | BeagleBoard: config: updated default configurationJason Kridner2011-09-04-2/+18
| | | | | | | | | | | | | | | | | | | | * Improved boot env var setting * Made room for a 64MB ramdisk by moving from 0x81600000 to 0x81000000 * Added ramarg, ramroot and ramboot env variables Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: Enabled multibus support for I2C in configurationJason Kridner2011-09-04-0/+6
| | | | | | | | | | | | Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: add optargs/buddy/cameraJason Kridner2011-09-04-0/+6
| | | | | | | | | | | | | | | | | | | | buddy and camera are used to configure peripherals in the kernel at boot time that cannot easily be detected by the kernel. Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: increase command-line functionalityJason Kridner2011-09-04-1/+2
| | | | | | | | | | | | | | | | | | Enable the expression evaluator. Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: make mtest runJason Kridner2011-09-04-4/+5
| | | | | | | | | | | | | | | | | | Utilize the alternate mtest and define a valid region. Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: enable DSSKoen Kooi2011-09-04-0/+1
| | | | | | | | | | | | Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: enable asix driver and dhcpKoen Kooi2011-09-04-1/+2
| | | | | | | | | | | | Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: enable networkingKoen Kooi2011-09-04-2/+8
| | | | | | | | | | | | Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | BeagleBoard: config: decrease bootdelay to 2 secondsKoen Kooi2011-09-04-1/+1
| | | | | | | | | | | | Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit v1.1 at 2024-11-07 20:12:57 +0000