summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* MLK-10576 ARM: i.MX6: exclude the ARM errata from i.MX6 UP systemNitin Garg2015-04-13-0/+3
| | | | | | | | | | | | | | | | The ARM errata 751472, 794072, 761320, 845369 only applied to the following configuration: This erratum affects configurations with either: - One processor if the ACP is present - Two or more processors i.MX6 family does not have the ACP and thus only the MPCore system will be impacted, which are the i.MX6DQ, i.MX6DL. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> (cherry picked from commit 0db960784ba4f631ee5c0321b5d25f3b1ac55640)
* MLK-10524: iMX6x: Implement workaround for Cortex-A9 errata 845369Nitin Garg2015-04-13-0/+1
| | | | | | | | | | Under very rare timing circumstances, transitioning into streaming mode might create a data corruption. Present on Two or more processors or 1 core with ACP, all revisions. This erratum can be worked round by setting bit[22] of the undocumented Diagnostic Control Register to 1. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit 70ad44e523680de67dd8b7a7505d7f27799980ee)
* mx6: drop ARM errata 742230Shawn Guo2015-04-13-1/+0
| | | | | | | | | | | | | | | | Commit e9fd66defd7e (ARM: mx6: define CONFIG_ARM_ERRATA_742230) enables errata 742230 for imx6, because it helps remove one reboot issue. However, this errata does not really apply on imx6, because Cortex-A9 on imx6 is r2p10 while the errata only applies to revisions r1p0..r2p2. At a later time, commit f71cbfe3ca5d (ARM: Add workaround for Cortex-A9 errata 794072) adds support of errata 794072, which applies to all Cortex-A9 revisions. As the workaround for both errata are exactly same, it makes a lot more sense to select 794072 instead of 742230 for imx6. Since we already enable 794072 for imx6, it's time to drop errata 742230 to avoid confusion. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* MLK-9953 pcie: disable pcie on imx6sx platformsl5.0.0_1.0.0-alphakk4.4.3_2.0.0-gaRichard Zhu2014-12-04-1/+11
| | | | | | | | | | | | | | | The PCIe support in uboot would bring failures in i.MX6SX PCIe EP/RC validations. Disable PCIe support in uboot here. RootCause: The bit10(ltssm_en) of GPR12 would be set in uboot, thus the i.MX6SX PCIe EP would be cheated that the other i.MX6SX PCIe RC had been configured and trying to setup PCIe link directly, although the i.MX6SX RC is not properly configured at that time. PCIe can be supported in uboot, if the i.MX6SX PCIe EP/RC validation is not running. Signed-off-by: Richard Zhu <Richard.Zhu@freescale.com> (cherry picked from commit db79603eeb96ca2e55336fc25b0529c249247454)
* MA-5830 Align Fastboot NAND config with bootloader partition 64Mguoyin.chen2014-12-02-0/+8
| | | | | | | Align the "MLK-9918: Reserve more space in uboot partition for NAND boot configurations" to enlarge the bootloader partition to be 64M Signed-off-by: guoyin.chen <guoyin.chen@freescale.com>
* MLK-9938 GIS: Enable GIS function on imx6sx SDB boardSandor Yu2014-12-02-1/+7
| | | | | | | | Enable GIS function on imx6sx SDB uboot. Expand CONFIG_SYS_MALLOC_LEN to 16M. Signed-off-by: Sandor Yu <R01008@freescale.com> (cherry picked from commit add90339c4e0ac9630f3c2a34d46b4f60265f56f)
* MLK-9927 - change the kernel and dtb location for nand readAllen Xu2014-11-30-6/+6
| | | | | | | | | kernel and dtb file location should be changed from 0x1000000 and 0x2000000 to 0x4000000 and 0x5000000, since the uboot partition expanded to 64M. Signed-off-by: Allen Xu <b45815@freescale.com> (cherry picked from commit eb4e6a6e65fe9074095869ecd5ccfe0a1559917d)
* MLK-9918: Reserve more space in uboot partition for NAND boot configurationsAllen Xu2014-11-22-7/+7
| | | | | | | | Expand the uboot space to 64m to reserve enough space for FCB, DBBT and u-boot. Signed-off-by: Allen Xu <b45815@freescale.com> (cherry picked from commit 54b3f6ba9097f4ed4cc8953a806c872444875a29)
* MLK-9854 mtd index change for imx6 sabreautoAllen Xu2014-11-16-0/+7
| | | | | | | | Modified the mtd index for imx6 sabreauto board, split the parallel nor to two partitions and the NAND index could be align with imx6sx board for mfgtool download. Signed-off-by: Allen Xu <b45815@freescale.com>
* MLK-9853 changed the mtd index for rootfs on imx6sx sabreautoAllen Xu2014-11-16-1/+1
| | | | | | | | On imx6sx sabreauto, both QSPI1 and NAND would be mapped as mtd devices, since we have already set the kernel to load QSPI1 first, the mtd index for NAND need to be changed. Signed-off-by: Allen Xu <b45815@freescale.com>
* MLK-9748 imx: mx6sxsabreauto: Add GIS supportYe.Li2014-11-06-1/+7
| | | | | | | | | | MX6SX sabreauto board has analog video input from VADC. Add the GIS support for this board that video input can display on LVDS at booting. The environment variable "gis" must be set to "vadc" to enable the function. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 5f2008a6dc08f07d462a063a0642f5e54fedbd21)
* MLK-9734 imx: mx6sxsabreauto: Add NAND boot environment variablesYe.Li2014-10-24-0/+23
| | | | | | | For NAND boot, the kernel zImage and rootfs also need to load from NAND. Add the environment variables for this. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-9697 pcie: PERST_GPIO and POWER_GPIO are currently swappedRichard Zhu2014-10-24-2/+2
| | | | | | Fix the GPIO assignments as per the board schematics. Signed-off-by: Richard Zhu <richard.zhu@freescale.com>
* MLK-9705 imx: mx6sxsabreauto: add MAX7310 support to reset peripheralsYe.Li2014-10-20-0/+5
| | | | | | | | | The MAX7310 uses I2C3 bus. At system initialization, enable the driver to: 1. Reset CPU_PER_RST_B signal 2. Set the steering for ENET 3. Enable the LVDS display Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-9652 Android: imx6sxsabreauto: Add android features supportYe.Li2014-10-09-0/+60
| | | | | | Add android fastboot, recovery and booti support for mx6sx sabreauto board. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-9665-2 mx6sx: define CONFIG_SPI_FLASH_BARPeng Fan2014-10-09-0/+3
| | | | | | | | | | | | define CONFIG_SPI_FLASH_BAR in mx6sx_arm2.h mx6sxsabreauto.h to enable access to flash array higher than 16MB. CONFIG_SPI_FLASH_BAR is also set in mx6sxsabresd.h for RevB board. Actually, if QSPI flash size <= 16MB, setting CONFIG_SPI_FLASH_BAR has not effect. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-9646 imx: mx6sxsabreauto: Change DDR size to 2GYe.Li2014-09-29-1/+1
| | | | | | | | The mx6sx sabreauto boards uses 2G DDR3. Modify the configuration PHYS_SDRAM_SIZE to this size. Signed-off-by: Ye.Li <B37916@freescale.com> Acked-by: Jason Liu
* ENGR00333317 imx: mx6sxsabreauto: Add BSP support for AI boardYe.Li2014-09-26-0/+386
| | | | | | | | | | | | | | | | Create mx6sx sabreauto BSP file and configurations. The devices below have been supported: 1. SD/MMC/eMMC on SDA/SDB (base board) sockets 2. USB OTG port and USB HOST port (base board) 3. NAND flash 4. QuadSPI flash on QSPI1 5. I2C 6. PMIC PFUZE100 7. Onboard ethernet chip on ENET2 8. Splash screen on LVDS Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00331706-5 imx: mx6: Enable 24Mhz OSC for GPTYe.Li2014-09-18-0/+1
| | | | | | | Set the CONFIG_MXC_GPT_HCLK configuration in mx6_common.h, so that enable the 24Mhz OSC GPT on all MX6 platforms. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00328278-1: Fix i.MX6DQ/DL arm2 LPDDR2 boards mem sizeNitin Garg2014-09-04-5/+0
| | | | | | | Couple of issues in commit 21a2eb5f. The RAM size is wrong and max number of DCD is 220. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00325255 pcie:enable pcie support on imx6sx sdRichard Zhu2014-07-31-0/+10
| | | | | | | | | | | | | | Enable pcie support in uboot on imx6sx sd boards - enable_pcie_clock should be call before ssp_en is set, since that ssp_en control the phy_ref clk gate, turn on it after the source of the pcie clks are stable. - add debug info - add rx_eq of gpr12 on imx6sx - there are random link down issue on imx6sx. It's pcie ep reset issue. solution:reset ep, then retry link can fix it. Signed-off-by: Richard Zhu <r65037@freescale.com>
* ENGR00324352 Set console value to show log info for mfgtool nand downloadAllen Xu2014-07-24-0/+1
| | | | | | set console value to show download log info for mfgtool NAND download. Signed-off-by: Allen Xu <b45815@freescale.com>
* ENGR00323465: iMX6SX ARM2: modified NAND boot rootfs mtd partition numAllen Xu2014-07-14-1/+1
| | | | | | | | Since QSPI will be disabled for NAND module(pin conflict), the mtd partition number will be count from 0, the last partition for rootfs need to be changed from 4 to 3. Signed-off-by: Allen Xu <b45815@freescale.com>
* ENGR00323143 pcie:can't be enabled in both uboot and kernelRichard Zhu2014-07-17-1/+12
| | | | | | | | | | | | | | imx6 q/dl/solo pcie would be failed to work properly in kernel, if the pcie module is iniialized/enumerated both in uboot and linux kernel. rootcause:imx6 q/dl/solo pcie don't have the reset mechanism. it is only be RESET by the POR. So, the pcie module only be initialized/enumerated once in one POR. Set to use pcie in kernel defaultly, mask the pcie config here. Remove the mask freely, if the uboot pcie functions, rather than the kernel's, are required. Signed-off-by: Richard Zhu <r65037@freescale.com>
* ENGR00322796 iMX6SXSABRESD: Enable Micron N25Q128 flash support for RevB boardYe.Li2014-07-17-0/+1
| | | | | | | | | The iMX6SX SABRESD RevB board uses Micron N25Q128 to replace Spansion S25FL128 on RevA board. So enable the CONFIG_SPI_FLASH_STMICRO and CONFIG_SPI_FLASH_SPANSION to support both two revisions. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321137 mx6sx: arm2: Expand malloc pool to 32MSandor Yu2014-07-08-1/+1
| | | | | | | | | | | | GIS module need about 3M+3M+1.5M+1.5M=9M memory. When gis module enabled, malloc may failed to allocate memory for other modules, that may cause system hang. Expand malloc pool to 32M, system hang issue can not duplicate on mx6sx arm2 board. pass one night reset stress test. Signed-off-by: Sandor Yu <R01008@freescale.com>
* ENGR00321260-2 iMX6:Android: Append the "androidboot.serialno" to bootargsYe.Li2014-07-04-0/+6
| | | | | | | | | | | | | Android supports to two ways to pass serialno: 1. ATAG_SERIAL 2. "androidboot.serialno=" argument in boot commandline. Since we support the DTB for android, so the ATAGS can't work. We have to choose the second way. This patch only applys the bootargs in bootimg, while the bootargs saved in u-boot env variables won't have this argument appended. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321085 iMX6SX:SABRESD: Enable the eMMC boot specific commandsYe.Li2014-07-04-0/+1
| | | | | | | | | The v2014 u-boot provides some “mmc” sub-commands for setting eMMC boot parameters, such as boot bus, partition, etc. These sub-commands are controlled by "CONFIG_SUPPORT_EMMC_BOOT". Enable this configuration for iMX6SXSABRESD board. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00321077 iMX6: Enable the mtest command for DDR testYe.Li2014-07-03-0/+5
| | | | | | | The mtest is no longer default in v2014. To test the DDR, enable this command for each iMX6 board. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00320125 iMX6: Change to use dynamical mmcrootYe.Li2014-06-30-45/+29
| | | | | | | | | | | | | | | | | | | | | | | | | The kernel changes to fix the mmcblk index with USDHC controllers as below: mmcblk0 ---> USDHC1 mmcblk1 ---> USDHC2 mmcblk2 ---> USDHC3 mmcblk3 ---> USDHC4 So in u-boot, the "mmcroot" must be updated together. When booting from SD/MMC device, change the "mmcroot" to dynamically set according to the boot USDHC controller. It is the same mechanism as "mmcdev" used for kernel image loading. Therefore, the uboot, kernel image, dtb and rootfs are required in same SD/MMC card. To disable the mmc dynamical detection, set the "mmcautodetect" to "no", then "mmcroot" and "mmcdev" will not be overwritten. When booting from other devices which needs to load kernel, dtb and rootfs from SD/MMC card, their "mmcdev" reset vaule is CONFIG_SYS_MMC_ENV_DEV and "mmcroot" reset value is CONFIG_MMCROOT. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00319772 iMX6SX:ARM2: Add EIM-NOR support for 17x17 ARM2 boardYe.Li2014-06-25-0/+9
| | | | | | | | | | | | | | The NOR flash PC28F00AG18 has 512 of 256KB erase blocks which are locked after power on reset. Change the 17x17 ARM2 configurations to match the flash parameters, and enable the CONFIG_SYS_FLASH_PROTECTION to allow write to the flash. The EIM-NOR on 17x17 ARM2 board uses MUXed mode. This has less effort on board rework. When boot from EIM-NOR, set SW8, SW7, SW5 to all off. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00319151-1 iMX6SX: Change default boot to use bootz and zImageYe.Li2014-06-20-57/+57
| | | | | | | Modified the default boot commands of all iMX6SX boards to use bootz and zImage. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-82 mx6sx arm2: Enable gis functionYe.Li2014-06-17-1/+7
| | | | | | | | Enable gis function for mx6sx 19x19 arm2 board Expand malloc buf pool to 16M. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-81 gis: Add gis moduleYe.Li2014-06-17-0/+29
| | | | | | | | Add gis module, current gis is support vadc input. Add power down function to lcdif driver. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-73 iMX6SX:SABRESD/ARM2 Add "bmode" command supportYe.Li2014-06-17-0/+4
| | | | | | | | | | | | | Enable the "CONFIG_CMD_BMODE" and add BSP support. "bmode" supports to reboot: SD4, QSPI2 (SABRESD) SD2, SD3, eMMC, QSPI2, NAND, SPINOR (17x17 ARM2) SD1, QSPI2, SPINOR, EIMNOR (19x19 ARM2) BTW: Board rework is needed on ARM2 for NAND, SPINOR or EIMNOR boot. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-72 iMX6SX:SABRESD/19x19ARM2 Add splash screen support in BSPYe.Li2014-06-17-2/+53
| | | | | | | | | | | | Enable the video drivers and MXS LCDIF driver to support the splash screen on MX6SX SDB and 19x19 ARM2. Add BSP codes for video parameters and LCDIF/LVDS initialization. "panel" env is used for selecting the display panel. Set "panel" env to "Hannstar-XGA" for LVDS display. Set "panel" env to "MCIMX28LCD" for parallel LCD display. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-70 iMX6SX:Video Update MXS LCDIF driverYe.Li2014-06-17-0/+15
| | | | | | | | | | | | Add a new interface "mxs_lcd_panel_setup" to setup fb parameters and specifies the LCDIF controller for multiple controllers of iMX6SX. Pass fb parameters via "videomode" env remains work if the new interface is not called before video initialization. Modify LCDIF clock interface "mxs_set_lcdclk" to support multiple LCDIF controllers on iMX6SX. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-68 iMX6SX:SABRESD: Add Android features supportYe.Li2014-06-17-0/+54
| | | | | | | Add BSP codes to mx6sxsabresd to support android uboot features: fastboot, booti and recovery Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-67 iMX6SX:SABRESD Disable the RDC temporarilyYe.Li2014-06-17-1/+1
| | | | | | | Disable RDC in u-boot till kernel implements it. Otherwise, crash may happen in kernel. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-66 iMX6SX:SABRESD Support M4 fast boot at early stageYe.Li2014-06-17-2/+7
| | | | | | | | | | | | | | | | T support M4 boot in 50 ms, kick start M4 at "board_early_init_f" stage where u-boot passes ARM and architecture initialization. Add a configuration "CONFIG_SYS_AUXCORE_FASTUP" for this feature enablement. And a build config "mx6sxsabresd_m4fastup". Adjust the default M4 image address to 0x78000000 represented by "CONFIG_SYS_AUXCORE_BOOTDATA". When M4 fast boot is enabled, RDC should be enabled together and the QSPI driver must turn off, because M4 is running on QSPI flash in XIP. Setup this relationship by configurations. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-64 iMX6SX: Add MX6SX SABRE SD board supportYe.Li2014-06-17-0/+332
| | | | | | | | | | | | Add BSP codes for iMX6SX SABRE SD board to support SD/MMC, USB, QSPI2 NOR Flash, Ethernet, I2C, PMIC and M4 command boot(bootaux). Add board build targets of SABER SD for boot device: mx6sxsabresd --- SD/MMC mx6sxsabresd_qspi2 --- QuadSPI2 NOR flash Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-62 iMX6SX: Add MX6SX 19x19 DDR3 ARM2 board supportYe.Li2014-06-17-0/+17
| | | | | | | | | | | | | | | | | | | Add BSP codes for iMX6SX 19x19 DDR3 ARM2 board to support SD/MMC, USB, QSPI2 NOR Flash, SPI NOR flash, WEIM NOR Flash, Ethernet, I2C, PMIC and M4 command boot(bootaux). Some features has conflicts, so can't be enabled at same time: WEIM-NOR <---> QSPI pin conflict QSPI <---> SPI-NOR u-boot driver conflict SPI-NOR <---> SD2 pin conflict Add board build targets of 19x19 DDR3 ARM2 for boot device: mx6sx_19x19_ddr3_arm2 --- SD/MMC/eMMC mx6sx_19x19_ddr3_arm2_spinor --- SPINOR on ECSPI4 CS0 mx6sx_19x19_ddr3_arm2_eimnor --- WEIM NOR flash mx6sx_19x19_ddr3_arm2_qspi2 --- QuadSPI2 NOR flash Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-61 iMX6SX: Add MX6SX 17x17 ARM2 board supportYe.Li2014-06-17-0/+444
| | | | | | | | | | | | | | | | | | | Add BSP codes for iMX6SX 17x17 ARM2 board to support SD/MMC, USB, QSPI2 NOR Flash, SPI NOR flash, NAND Flash, Ethernet, I2C ,PMIC and M4 command boot (bootaux). Some features has conflicts, so can't be enabled at same time: QSPI <---> NAND pin conflict QSPI <---> SPI-NOR u-boot driver conflict SPI-NOR <---> SD2 pin conflict Add board build targets of 17x17 ARM2 for boot device: mx6sx_17x17_arm2 --- SD/MMC/eMMC mx6sx_17x17_arm2_spinor --- SPINOR on ECSPI4 CS0 mx6sx_17x17_arm2_nand --- NAND flash mx6sx_17x17_arm2_qspi2 --- QuadSPI2 NOR flash Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-47 i.mx6:arm2/slevk Enable the CONFIG_SYS_GENERIC_BOARDYe.Li2014-06-17-0/+2
| | | | | | | Using the CONFIG_SYS_GENERIC_BOARD for imx6 arm2 board and imx6slevk to sync the deprecation process for generic board on upstream. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-45 ARM:imx6:sabreauto Add USB HOST BSP supportYe.Li2014-06-17-9/+17
| | | | | | | | | | | | Sabreauto board has pin conflict (pin EIM_D18) between NOR flash and i2c3. To enable the USB host, the i2c3 must be used to operate the max7310 IO expander to output the VBUS power. As SPINOR is enabled at default, it is impossible to use USB host at same time. Thus, remove the SYS_USE_SPINOR from sabreauto configurations to disable SPINOR. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-43 ARM:imx6 Enable OCOTP driver and fuse commandYe.Li2014-06-17-0/+12
| | | | | | | | | | | | | Enable the fuse command config "CONFIG_CMD_FUSE" and OCOTP driver "CONFIG_MXC_OCOTP" for imx6. Users can use "sense" and "prog" to access the fuse directly, or use "read" and "override" to access shadow registers. Supported boards: mx6qdlsabresd, mx6qdlsabreauto, mx6qdlarm2, mx6slevk Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-41 i.mx6:sabresd/sabreauto/slevk Fix build break for android ↵Ye.Li2014-06-17-0/+78
| | | | | | | | | | support Add the android header file "mx6slevkandroid.h" for imx6slevk android support. Fix header file and pin name problems in BSP codes. Remove build warning in cmd_fastboot.c Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-40 i.mx6dl: arm2: add the i.MX6DL arm2 board supportYe.Li2014-06-17-1/+5
| | | | | | | | | | | | | | | | This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2 shared the same board with i.MX6Q ARM2 board since the i.MX6DL is pin-pin compatible with i.MX6Q. The patch also support the DDR 32-BIT mode option. Please define CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT mode.But due to the board design, it's 64bit DDR buswidth physically, so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it. The patch has been tested on the i.MX6Q and i.MX6DL arm2 board. Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-39 Splash screen: correct i.MX6dl ipu hsp clock rateYe.Li2014-06-17-0/+4
| | | | | | | | | | | i.MX6dl ipu hsp clock rate is 270MHz in kernel. In uboot, i.MX6dq ipu hsp clock rate is 264MHz, and i.MX6dl ipu hsp clock rate is 198MHz. Correct i.MX6dl ipu hsp clock rate, display will get correct pixel clock now. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-38 MX6 Sabreauto:Add IPUv3 splash screen supportYe.Li2014-06-17-16/+16
| | | | | | | | | | | | | | | | This patch adds IPUv3 splash screen support for the MX6Q/SDL Sabreauto platforms. The default display is the Hannstar-XGA LVDS panel. Users may set the uboot variable 'panel' to be 'HDMI' to switch to use HDMI splash screen. To avoid duplicate configures on different sabre platforms, this patch moves the IPUv3 splash screen relevant configures to the head file 'mx6qsabre_common.h'. Also, this patch modifies the condition to build in EPDC splash screen feature in order to avoid the build break due to the migration of the IPUv3 splash screen relevant configures. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
generated by cgit v1.1 at 2024-11-22 07:22:50 +0000