summaryrefslogtreecommitdiff
path: root/include
Commit message (Collapse)AuthorAgeLines
* ftsdmc020: move ftsdmc020.h to include/faradayMacpaul Lin2011-04-27-0/+103
| | | | | | | | | | Move the header file "ftsdmc020.h" (SDRAM Controller) to "include/faraday" folder. This change will let other SoC which also use ftsdmc020 could share the same header file. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* cpu9260: update board supportEric Benard2011-04-27-98/+167
| | | | | | | | | | | | | | | - update to new relocation code - switch to boards.cfg - get rid of LEGACY (still a little hack in .h to compile) - add nand boot configuration - boot tested for the following configurations : 9260 (64MB RAM & nor boot) 9260_nand (64MB RAM & nand boot) 9G20_128M (128MB RAM & nor boot) 9G20_nand_128M (128MB RAM & nand boot) (nor boot is using lowlevel init) Signed-off-by: Eric Bénard <eric@eukrea.com>
* ARMV7: OMAP3: Add support for Comelit DIG297 boardLuca Ceresoli2011-04-27-0/+311
| | | | | | | | | | | | | | Board support for the DIG297 board manufactured by Comelit Group SpA. It is a custom board based on the BeagleBoard <http://beagleboard.org/> by Texas Instruments. The board support is based on the BeagleBoard implementation. Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.aribaud@free.fr> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARMV7: OMAP3: Cleanup extern variables in mem.cLuca Ceresoli2011-04-27-123/+53
| | | | | | | | | | | | Removed boot_flash_* extern variables. boot_flash_type was totally unused. The other ones were actually constants, so they have been replaced with #defines in the board config files. Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.aribaud@free.fr> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* arm: Tegra2: add support for A9 CPU initTom Warren2011-04-27-0/+4
| | | | Signed-off-by: Tom Warren <twarren@nvidia.com>
* omap3_beagle: enable EHCI and USB storage.Alexander Holler2011-04-27-0/+6
| | | | | | | | | | The reset sequence/configuration for ehci is highly board specific, so this will be done in the source for the board, instead of introducing several CONFIG_* which would be needed to make those few lines in beagle.c usable across different OMAP boards. Signed-off-by: Alexander Holler <holler@ahsoftware.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARM: OMAP3: Revamp IGEP module default configurationEnric Balletbo i Serra2011-04-27-5/+52
| | | | | | | | The default IGEP configuration doesn't do anything useful; using some boot.scr search logic like BeagleBoard is much more useful. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARM: OMAP3: Revamp IGEP v2 defaultEnric Balletbo i Serra2011-04-27-5/+52
| | | | | | | | | | | configuration The default IGEP configuration doesn't do anything useful; using some boot.scr search logic like BeagleBoard is much more useful. Signed-off-by: Loïc Minier <loic.minier@linaro.org> Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Replace obsolete e-mail addressAlbert ARIBAUD2011-04-27-1/+1
| | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* fttmr010: move fttmr010 header to include/faradayMacpaul Lin2011-04-27-0/+73
| | | | | | | | | | | Move the header file and definitions of fttmr010 power control unit from a320 SoC folder to "include/faraday" folder. This change will let other SoC which also use fttmr010 could share the same header file. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* ftpmu010.h: add asm support used by lowlevel_initMacpaul Lin2011-04-27-0/+62
| | | | | | | Add asm support which is ususally used in lowlevel_init to set power related parameters to sdram controller and static memory controller. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* ftpmu010: fix relocation and enhance featuresMacpaul Lin2011-04-27-3/+35
| | | | | | | | | | | | | | | | | | | 1. ftpmu010.h: fix and add definitions Enhanced for more features and asm related support according to datasheet. Note: - FTPMU010_PDLLCR0_HCLKOUTDIS is "incorrect" in datasheet. - FTPMU010_PDLLCR0_DLLFRANG is only 1 bit at bit #19. (not 20-19) - FTPMU010_PDLLCR0_HCLKOUTDIS is 4 bits at bit #20. (not 24-21) 2. ftpmu010.c: enhance features and fix relocation - The following functions is added for pmu features. ftpmu010_mfpsr_select_dev() ftpmu010_sdramhtc_set() - This patch also fix the declare statement for relocation. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* I2C: add i2c support for Armada100 platformLei Wen2011-04-27-0/+1
| | | | | | | | Add i2c support to aspenite board with Armada100 soc. Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Lei Wen <leiwen@marvell.com>
* I2C: add i2c support for Pantheon platformLei Wen2011-04-27-0/+2
| | | | | | | | Add i2c support to dkb board with pantheon soc. Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Lei Wen <leiwen@marvell.com>
* mv_i2c: use structure to replace the direclty defineLei Wen2011-04-27-0/+2
| | | | | | | | | | Add i2c_clk_enable in the cpu specific code, since previous platform it, while new platform don't need. In the pantheon and armada100 platform, this function is defined as NULL one. Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Lei Wen <leiwen@marvell.com>
* pxa: move i2c driver to the common placeLei Wen2011-04-27-0/+2
| | | | | | | | | For better sharing with other platform other than pxa's, it is more convenient to put the driver to the common place. Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Lei Wen <leiwen@marvell.com>
* ARMV7: Vexpress: Remove config.mkMatt Waddel2011-04-27-0/+1
| | | | | | Remove obsolete board config.mk. Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
* arm: a320: use new ftpmu010 APIPo-Yu Chuang2011-04-27-0/+5
| | | | | | | ftpmu010 related code has been moved to drivers/power/. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
* power: ftpmu010: move drivers/power/ftpmu010.h to include/faradayPo-Yu Chuang2011-04-27-0/+150
| | | | | | | Also add API declarations. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
* OMAP3: CM-T35: Add support for CM-T3730Igor Grinberg2011-04-27-6/+6
| | | | | | | | CM-T3730 is exactly the same board as CM-T35, but it has TI DM3730 SoC onboard and therefore some changes have to take place Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: CM-T35: enable the green LEDIgor Grinberg2011-04-27-0/+15
| | | | | Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: CM-T35: fix mmcIgor Grinberg2011-04-27-2/+1
| | | | | | | Use CONFIG_OMAP3_MMC in cm-t35 configuration file. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: CM-T35: update board files header informationIgor Grinberg2011-04-27-3/+3
| | | | | Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: CM-T35: update configIgor Grinberg2011-04-27-1/+4
| | | | | | | update config for OMAP3 CM-T35 Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARMV7: AM3517/05: Add support for CraneBoard.Srinath2011-04-27-0/+340
| | | | | | | | It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments Please refer to <www.craneboard.org> for more details. Signed-off-by: Srinath <srinath@mistralsolutions.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: BeagleBoard: add xM rev B to ID tableKoen Kooi2011-04-27-1/+1
| | | | | | | | | | | | Patch was updated by Jason Kridner <jkridner@beagleboard.org>: * Use tabs to match style of other board revisions * Only include board revisions that exist * Default to the same configuration as the latest revision, but without setting 'beaglerev' Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap3_beagle: enable the use of a plain text fileAlexander Holler2011-04-27-12/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | Using the new env import command it is possible to use plain text files instead of script-images. Plain text files are much easier to handle. E.g. If your boot.scr contains the following: ----------------------------------- setenv dvimode 1024x768-16@60 run loaduimage run mmcboot ----------------------------------- you could create a file named uEnv.txt and use that instead of boot.scr: ----------------------------------- dvimode=1024x768-16@60 uenvcmd=run loaduimage; run mmcboot ----------------------------------- The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence will be started, therefore you could just use ----------------------------------- dvimode=1024x768-16@60 ----------------------------------- as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* BeagleBoard: Added LED driverJason Kridner2011-04-27-0/+13
| | | | | | | | | | Added LED driver using status_led. USR0 is set to monitor the boot status. USR1 is set to be the green LED. Included adding configuration and command to the default configuration. Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* IMX: MX31: Cleanup include files and drop nasty #ifdef in driversStefano Babic2011-04-27-4/+4
| | | | | | | | | | As exception among the i.MX processors, the i.MX31 has headers without general names (mx31-regs.h, mx31.h instead of imx-regs.h and clock.h). This requires several nasty #ifdef in the drivers to include the correct header. The patch cleans up the driver and renames the header files as for the other i.MX processors. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX5: Enable flat-device-tree support on mx51/53 evk boardLiu Hui-R643432011-04-27-0/+6
| | | | | | | | device tree for uboot arm support has already been enabled in the master branch. This patch enable device tree support for mx51/53 evk board for DT test. Signed-off-by: Jason Liu <r64343@freescale.com>
* MX31: qong: add watchdogStefano Babic2011-04-27-0/+1
| | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX51: drop config.mk from mx51evkStefano Babic2011-04-27-0/+2
| | | | | | | | The config.mk file in board directory is now obsolete and should be removed. Add option for the IMX image into boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
* mpc52xx, digsy_mtc: add trickle charger support for rev5 boards.Heiko Schocher2011-04-26-0/+2
| | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* ppc4xx: Do not stop booting on any keypress on dlvision-10gDirk Eibach2011-04-21-0/+4
| | | | | | | | Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be stopped with well defined keypresses. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Improve fan PWM curve on DLVision 10GDirk Eibach2011-04-21-1/+2
| | | | | Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Enable MPC92469AC on DLVision 10GDirk Eibach2011-04-21-3/+6
| | | | | Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Set DLVision 10G osd position to linux defaultsDirk Eibach2011-04-21-2/+5
| | | | | Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Adapt DLVision 10G to new FPGA firmwareDirk Eibach2011-04-21-5/+5
| | | | | Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Enable LM64 on DLVision 10GDirk Eibach2011-04-21-1/+1
| | | | | Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* Merge branch 'phylib' of git://git.denx.de/u-boot-mmcWolfgang Denk2011-04-20-316/+1403
|\
| * fsl: Change fsl_phy_enet_if to phy_interface_tAndy Fleming2011-04-20-21/+21
| | | | | | | | | | | | | | | | | | | | | | | | The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum. This meant that drivers which used fsl_phy_enet_if to deal with PHY interfaces would have to convert between the two (or we would have to have them mirror each other, and deal with the ensuing maintenance headache). Instead, we switch all clients of fsl_phy_enet_if over to phy_interface_t, which should become the standard, anyway. Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
| * tsec: Convert tsec to use PHY LibAndy Fleming2011-04-20-275/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | This converts tsec to use the new PHY Lib. All of the old PHY support is ripped out. The old MDIO driver is split off, and placed in fsl_mdio.c. The initialization is modified to initialize the MDIO driver as well. The powerpc config file is modified to configure PHYLIB if TSEC_ENET is configured. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
| * phylib: Add a bunch of PHY drivers from tsecAndy Fleming2011-04-20-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The tsec driver had a bunch of PHY drivers already written. This converts them all into PHY Lib drivers, and serves as the first set of PHY drivers for PHY Lib. While doing that, cleaned up a number of magic numbers (though not all of them, as PHY vendors like to keep their numbers as magical as possible). Also, noticed that almost all of the vitesse/cicada PHYs had the same config/parse/startup functions, so those have been collapsed into one. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
| * Create PHY Lib for U-BootAndy Fleming2011-04-20-0/+1235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extends the mii_dev structure to participate in a full-blown MDIO and PHY driver scheme. The mii_dev structure and miiphy calls are modified in such a way to allow the original mii command and miiphy infrastructure to work as before, but also to support a new set of APIs which allow (among other things) sharing of PHY driver code and 10G support The mii command will continue to support normal PHY management functions (Clause 22 of 802.3), but will not be changed to support 10G (Clause 45). The basic design is similar to PHY Lib from Linux, but simplified for U-Boot's network and driver infrastructure. We now have MDIO drivers and PHY drivers An MDIO driver provides: read write reset A PHY driver provides: (optionally): probe config - initial setup, starting of auto-negotiation startup - waiting for AN, and reading link state shutdown - any cleanup needed The ethernet drivers interact with the PHY Lib using these functions: phy_connect() phy_config() phy_startup() phy_shutdown() Each PHY driver can be configured separately, or all at once using config_phylib_all_drivers.h (added in the patch which adds the drivers) We also provide generic drivers for Clause 22 (10/100/1000), and Clause 45 (10G) PHYs. We also implement phy_reset(), and call it in phy_connect(). Because phy_reset() is essentially the same as miiphy_reset, but: a) must support 10G PHYs, and b) should use the phylib primitives, we implement miiphy_reset, using phy_reset(), but only when CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this way, we save on compile size, even if we don't manage to save code size. Pulled ethtool.h and mdio.h from: git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6 782d640afd15af7a1faf01cfe566ca4ac511319d With many, many deletions so as to enable compilation under u-boot Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
| * miiphy: Fix some formatting issuesAndy Fleming2011-04-20-18/+18
| | | | | | | | | | | | | | | | Mostly putting a space between function name and "(", and doing return (foo) Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
| * tsec: use IO accessors for IO accessesMingkai Hu2011-04-20-4/+4
| | | | | | | | | | | | | | Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
* | Merge branch 'misc' of git://git.denx.de/u-boot-blackfinWolfgang Denk2011-04-20-2/+5
|\ \
| * | config_defaults.h: drop OSE bootm defaultMike Frysinger2011-04-13-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Most arches don't support OSE, and this is a new bootm target, so the likelihood of any board actually wanting this today is fairly low. Any board who actually wants this can enable it in the board-specific config without making it a default bloat. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | crc32: make command optionalMike Frysinger2011-04-13-1/+2
| | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | make `go` optionalMike Frysinger2011-04-13-0/+1
| | | | | | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit v1.1 at 2024-08-24 00:46:28 +0000