| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
|
|
|
|
| |
It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.
The crc checksum on data packet is enabled with the def,
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
|
|
|
|
| |
Added support for MMC/SD cards for Davinci. This feature is enabled by
CONFIG_DAVINCI_MMC and is dependant on CONFIG_MMC and CONFIG_GENERIC_MMC
options. This is tested on DM355 and DM365 EVMs with both the available mmc
controllers.
Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.
Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
| |
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
| |
|
|
|
|
|
|
|
|
| |
this eliminates compiler warnings when cmd_mmc.c is built with CONFIG_SYS_MMC_SET_DEV
the mmc_set_dev implementation in omap3_mmc.c is also tweaked to match
the new prototype in parameter naming and type
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
| |
|
|
| |
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The mmc code defines the response as an array of chars. However, it
access the response bytes both as (i) an array of four uints (with
casts) and (ii) as individual chars. The former case is used more
often, including by the driver when it assigns the response.
The char-wise accesses are broken on little endian systems because they
assume that the bytes in the uints are in big endian byte order.
This patch fixes this by changing the response to be an array of four
uints and replacing the char-wise accesses with equivalent uint-wise
accesses.
Signed-off-by: Rabin Vincent <rabin@rab.in>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Here's a new framework (based roughly off the linux one) for managing
MMC controllers. It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.
This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)
Some of this code was contributed by Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
|
|
|
|
| |
The current MMC infrastructure relies on the existence of an
arch-specific header file. This isn't necessary, and a couple
drivers were forced to implement dummy files to meet this requirement.
Instead, we move the stuff in those header files into a more appropriate
place, and eliminate the stubs and the #include of asm/arch/mmc.h
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
| |
This is to get it out of the way of incoming MMC framework
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
| |
MMC cards are not memory, so we stop treating them that way.
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This moves the MMC and SD Card command definitions from
include/asm/arch/mmc.h into include/mmc.h. These definitions are
given by the MMC and SD Card standards, not by any particular
architecture.
There's a lot more room for consolidation in the MMC drivers which
I'm hoping to get done eventually, but this patch is a start.
Compile-tested for all avr32 boards as well as lpc2292sodimm and
lubbock. This should cover all three mmc drivers in the tree.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
|
* Patches by Kyle Harris, 13 Mar 2003:
- Add FAT partition support
- Add command support for FAT
- Add command support for MMC
----
- Add Intel PXA support for video
- Add Intel PXA support for MMC
----
- Enable MMC and FAT for lubbock board
- Other misc changes for lubbock board
|
