arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	driver: net: cpsw: add support for RGMII id mode support and RMII clock ↵	Mugunthan V N	2016-10-13	-0/+1
\| \| \| \| \| \| \| \| \| \| \| \| \|	source selection cpsw driver supports only selection of phy mode in control module but control module has more setting like RGMII ID mode selection, RMII clock source selection. So ported to cpsw-phy-sel driver from kernel to u-boot. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
*	drivers: net: cpsw: Add reading of DT phy-handle node	Dan Murphy	2016-05-24	-0/+1
\| \| \| \| \| \| \| \| \| \| \| \| \|	Add the ability to read the phy-handle node of the cpsw slave. Upon reading this handle the phy-id can be stored based on the reg node in the DT. The phy-handle also needs to be stored and passed to the phy to access any phy data that is available. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
*	drivers: net: cpsw: add support for reading mac address from efuse	Mugunthan V N	2016-05-24	-0/+1
\| \| \| \| \| \| \| \| \| \| \| \| \|	Different TI platforms has to read with different combination to get the mac address from efuse. So add support to read mac address based on machine/device compatibles. The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c done by Tony Lindgren. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
*	drivers: net: cpsw: convert driver to adopt device driver model	Mugunthan V N	2015-10-22	-0/+2
\| \| \| \| \| \| \|	adopt cpsw driver to device driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
*	drivers: net: cpsw: add support for using second port as ethernet	Mugunthan V N	2014-07-25	-0/+1
\| \| \| \| \| \| \|	Add support for using the second slave port of cpsw to be used as primary ethernet. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
*	drivers: net: cpsw: add support to have phy address from cpsw platform data	Mugunthan V N	2014-03-04	-1/+1
\| \| \| \| \| \| \| \| \| \| \| \|	Some platforms like AM437x have different EVMs with different phy addresses, so this patch adds support for passing phy address via cpsw plaform data. Also renamed phy_id to phy_addr so better understanding of the code. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> [trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335 pengwyn boards] Signed-off-by: Tom Rini <trini@ti.com>
*	drivers: net: cpsw: remove hard coding bd ram for cpsw	Mugunthan V N	2013-07-26	-0/+1
\| \| \| \| \| \| \|	BD ram address may vary in various SOC, so removing the hardcoding and passing the same information through platform data Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
*	cpsw: add driver for cpsw ethernet device	Cyril Chemparathy	2012-09-01	-0/+51
	CPSW is an on-chip ethernet switch that is found on various SoCs from Texas Instruments. This patch adds a simple driver (based on the Linux driver) for this hardware module. This patch also adds support to clean and flush dcache during packet send and receive. Changes by Sandhya: Added support to clean and flush dcache during packet send/receive and added timeouts. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com> [Ilya: Cleaned cache handling, some style cleanup, some small fixes, use of internal RAM for descriptors] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>