summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* omap: add MMC and FAT support to SPLAneesh V2011-08-03-0/+10
| | | | | | | | | | | | | | - Add MMC raw and FAT mode boot support for OMAP - Provide a means by which parameters passed by ROM-code can be saved in u-boot. - Save boot mode related information passed by OMAP4 ROM-code and use it to determine where to load the u-boot from - Assumes that the image has a mkimage header. Gets the payload size and load address from this header. If the header is not detected assume u-boot.bin as payload Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap: add basic SPL supportAneesh V2011-08-03-0/+52
| | | | | | | | | | | | | - Provide alternate implementations of board_init_f() board_init_r() for OMAP spl. - Provide linker script - Initialize global data - Add serial console support - Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move it to board config header from config.mk Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: automatic sdram detectionAneesh V2011-08-03-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | Identify SDRAM devices connected to EMIF automatically: LPDDR2 devices have some Mode Registers that provide details about the device such as the type, density, bus width etc. EMIF has the capability to read these registers. If there are no devices connected to a given chip-select reading mode registers will return junk values. After reading as many such registers as possible and matching with expected ranges of values the driver can identify if there is a device connected to the respective CS. If we identify that a device is connected the values read give us complete details about the device. This along with the base AC timings specified by JESD209-2 allows us to do a complete automatic initialization of SDRAM that works on all boards. Please note that the default AC timings specified by JESD209-2 will be safe for all devices but not necessarily optimal. However, for the Elpida devices used on Panda and SDP the default timings are both safe and optimal. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: calculate EMIF register valuesAneesh V2011-08-03-0/+10
| | | | | | | | | | | | | | Calculate EMIF register values based on AC timing parameters from the SDRAM datasheet and the DDR frequency rather than using the hard-coded values. For a new board the user doen't have to go through the tedious process of calculating the register values. Instead, just provide the AC timings from the device data sheet as input and the driver will automatically calculate the register values. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk2011-08-02-10/+67
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-blackfin: Blackfin: jtag-console: fix timer usage Blackfin: switch to common display_options() Blackfin: serial: move early debug strings into .rodata section Blackfin: adi boards: also set stderr to nc with helper Blackfin: update anomaly lists to latest public info Blackfin: serial: convert to bfin_{read,write} helpers Blackfin: split out async setup Blackfin: adi boards: enable pretty flash progress output Blackfin: drop unused dma.h header from start code Blackfin: portmux: allow header to be included in assembly files Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings Blackfin: sync MMR read/write helpers with Linux Blackfin: gpio: optimize free path a little Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR Blackfin: uart: fix printf warning Blackfin: add init.elf helper code Blackfin: dont reset SWRST on newer bf526 parts Blackfin: adi boards: enable multi serial support by default Blackfin: uart: add multiple serial support Blackfin: uart: move debug buffers into local bss
| * Blackfin: adi boards: also set stderr to nc with helperMike Frysinger2011-07-12-1/+2
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * Blackfin: adi boards: enable pretty flash progress outputMike Frysinger2011-07-12-0/+5
| | | | | | | | | | | | | | | | For only ~150 bytes increase in size, we can get a nice flash progress indicator rather than just the boring dots (which don't tell too much about overall progress). So enable it for all ADI boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi supportHarald Krapfenbauer2011-07-12-3/+46
| | | | | | | | | | | | | | | | These boards have an mmc/sd slot on them connected over SPI, so enable the driver. Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settingsHarald Krapfenbauer2011-07-12-5/+10
| | | | | | | | | | | | | | | | These boards can have an addon card plugged onto them, so enable support for it. Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDRMike Frysinger2011-07-12-1/+0
| | | | | | | | | | | | | | Set the default post word location to an L1 data location for all Blackfin parts so things "just work" for most people. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * Blackfin: adi boards: enable multi serial support by defaultMike Frysinger2011-07-12-0/+4
| | | | | | | | | | | | Since this only adds less than 3KiB, enable for all ADI boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFGDaniel Schwierzeck2011-07-31-1/+1
| | | | | | | | | | | | | | | | | | This define is a board-specific config option and should be renamed to follow the U-Boot naming convention. Additionally, add an explaining comment for this option. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
* | MIPS: INCA-IP: rename inca-swap-bytes host toolDaniel Schwierzeck2011-07-31-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | The INCA-IP SoC belongs to the Lantiq XWAY SoC product portfolio. For the upcoming support of other Lantiq SoC devices this tool should not solely depend on the INCA-IP board. Rename the tool to xway-swap-bytes and add an config option to enable compilation optionally. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
* | powerpc/85xx: enable USB2 gadget mode for corenet ds boardShaohui Xie2011-07-29-0/+1
| | | | | | | | | | | | | | | | | | | | to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to 'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break out if it cannot find 'usb1', so drop the 'else' clause to make driver scan all the 'usbx'. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Fix build failure for P1023RDSKumar Gala2011-07-29-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | When we added the fman fdt fixup we forgot to fixup the P1023RDS platform. So we would get: fdt.c: In function 'fdt_fixup_fman_firmware': fdt.c:465:15: error: 'CONFIG_SYS_FMAN_FW_LENGTH' undeclared (first use in this function) fdt.c:465:15: note: each undeclared identifier is reported only once for each function it appears in Add the needed #defines in P1023RDS.h to fix this. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/p2041rdb: Enable SATA supportMingkai Hu2011-07-29-0/+20
| | | | | | | | | | Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | 85xx: enable FDT support for STX SSA boardWolfgang Denk2011-07-29-1/+6
| | | | | | | | | | | | | | | | We also have to shift TEXT_BASE to accomodate for the additional code size. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/p2041rdb: Enable backside L2 cache supportMingkai Hu2011-07-29-0/+2
| | | | | | | | | | Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Removed obsolete Netstal boardsNiklaus Giger2011-07-28-1142/+0
| | | | | | | | Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
* | cleanup: Fix typos and misspellings in various files.Mike Williams2011-07-28-2/+2
| | | | | | | | | | | | | | | | | | | | | | Recieve/Receive recieve/receive Interupt/Interrupt interupt/interrupt Addres/Address addres/address Signed-off-by: Mike Williams <mike@mikebwilliams.com>
* | km/common: moved eeprom config to pbec specific partStefan Bigler2011-07-28-6/+12
| | | | | | | | | | | | | | | | | | | | | | Moved eeprom config to specific part, to allow bigger eeprom write pages for km_kirkwood designs. Write page only used for env eeprom in std use cases. 24C128 has page size of 64bytes -> 8 time faster. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* | km/common: use u-boot.kwb for u-boot update function on armHolger Brunck2011-07-28-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | Now we use the standard u-boot make to build the Kirkwood binary. The output file is u-boot.kwb. So use this name for the tftp update function to avoid confusion, because this is the binary we need on Kirkwood. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* | km/common: enable cramfs and cramfs cmdlineHolger Brunck2011-07-27-1/+3
| | | | | | | | | | | | | | | | | | | | | | All the km boards uses CRAMFS images where the kernel is stored. This isn't architecture specific because we use it on ARM and POWERPC. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* | powerpc/km82xx: remove 82xx specific functions from common.cHolger Brunck2011-07-27-0/+7
| | | | | | | | | | | | | | | | | | | | Common code should be valid for more than one architecture, therefore the km82xx specific code was removed from common.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* | km/common: remove obsolete defines and headerHolger Brunck2011-07-27-10/+0
| | | | | | | | | | | | | | | | | | | | These defines and the header keymile_hdlc_enet.h are obsolete due to the removed hdlc code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* | km/common: simplify debug environmentHolger Brunck2011-07-27-15/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The debug environment which is stored in textfiles in the scripts directory was reworked. Two usecase are now present which can be executed simply from the default environment: run develop: this configures the environment to setup the rootfs via nfs run ramfs: this configures the environment to setup the rootfs in ram Each architecture now has a "arch" variable which is used to load the architecture specific debug scripts and to set the rootpath for NFS. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* | km/common: add test sw starting variableThomas Herzmann2011-07-27-0/+2
| | | | | | | | | | | | | | | | | | | | The test SW is started when the test_bank variable is set. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* | km/common: rework and simplify default environmentHolger Brunck2011-07-27-94/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is the second step to simplify and decrease the default environment for the keymile boards. The release usecase formaly used to set the production environment was removed and the default configuration is now the production environment. So the formar environment variable "release" which has done a lot of things in the past, simply erase the current environment and do a reset which forces u-boot to setup the default environment again. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* | digsy_mtc: move board into vendor dir and add vendor logoAnatolij Gustschin2011-07-27-0/+1
| | | | | | | | Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | mpc5200: digsy_mtc: add support for graphic extension boardAnatolij Gustschin2011-07-27-0/+27
| | | | | | | | | | | | | | | | | | | | Add detection and initialisation for graphic extension board and support splash screen when booting. Enable "bmp" command in the board configuration and provide "disp" command to be able to switch the display on/off. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* | Timer: Allow reset_timer() only for systems with low resolution timersGraeme Russ2011-07-26-0/+3
| |
* | board/tqm85xx: Create and tear down TLB for get_ram_size()Becky Bruce2011-07-22-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | We need a TLB entry to call get_ram_size(); the common code doesn't create one until *after* fixed_sdram() has determined the size. So we set up tlbs for the max possible size and tear them down once we're done with get_ram_size(); the common 85xx code will then set up a final set of tlb entries for the *actual* detected size of ddr. This prevents us from having TLB entries that are larger than DDR sitting around for very long, which is not a recommended scenario. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | fman: insert the Fman firmware into the device treeTimur Tabi2011-07-22-6/+20
| | | | | | | | | | | | | | | | | | | | | | | | The Fman device tree node binding allows for the entire Fman firmware binary data to be embedded in the device tree. This eliminates the need to have NOR flash mapped to Linux just so that the Fman driver can see the firmware. The location of the Fman firmware is taken from the 'fman_ucode' environment variable. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk2011-07-19-0/+22
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mmc: mmc: rescan fails on empty slot AT91:mmc:fix multiple read/write error mmc: Access mode validation for eMMC cards > 2 GiB mmc: sh_mmcif: add support for Renesas MMCIF mmc: fix the condition for MMC version 4 MMC: add marvell sdhci driver MMC: add sdhci generic framework MMC: add erase function to both mmc and sd MMC: unify mmc read and write operation mmc: Tegra2: Enable SD/MMC driver for Seaboard and Harmony mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3
| * | mmc: Tegra2: Enable SD/MMC driver for Seaboard and HarmonyTom Warren2011-07-15-0/+22
| |/ | | | | | | | | Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Andy Fleming <afleming@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-07-18-3/+199
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: ARM: MX5: Fix broken leftover TO-2 errata workaround MX31: Cleanup clock function scb9328: Add ARM relocation support am3517evm: change console device from ttyS2 to ttyO2 Remove volatile qualifier in get_ram_size() calls TI: TNETV107X Fix Build Error ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7 arm: add CONFIG_MACH_TYPE setting and documentation arm: add __ilog2 function Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm EfikaMX: Enable EXT2 booting EfikaMX: Add missing CONFIG_SYS_TEXT_BASE EfikaMX: Use correct imximage.cfg MX27: Update to autogenerated asm-offsets.h MX5: Update to autogenerated asm-offsets.h imx: Add support for zmx25 board imx: Make imx25 compatible to mxc_gpio driver and fix in tx25 imx: Add auto generation of asm-offsets.h for imx25 imx: Add support for USB EHCI on imx25 imx: Use correct imx25 reset.c imx: Add get_tbclk() function for imx25 ARM: Update maintainer of board scb9328 mx27: Make the UART port number explicit build: Add targets for auto gen of asm-offsets.h and use it in imx35 mx31pdk: cosmetic: Fix line over 80 characters
| * | scb9328: Add ARM relocation supportTorsten Koschorrek2011-07-18-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes compiler errors due to missing definitions of CONFIG_SYS_SDRAM_BASE and CONFIG_SYS_INIT_SP_ADDR. It also does some cleanup: CONFIG_SYS_TEXT_BASE was moved to scb9328.h, obsolete config.mk was removed. The scb9328 board has 1 DRAM bank, so don't ask for more banks. CONFIG_NR_DRAM_BANKS will ever be 1. Signed-off-by: Torsten Koschorrek <koschorrek@synertronixx.de>
| * | am3517evm: change console device from ttyS2 to ttyO2Yegor Yefremov2011-07-18-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | the serial device names have been changed from ttySx to ttyOx, so the console device name should be also changed to support the latest kernel versions. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Acked-by: Vaibhav Hiremath<hvaibhav@ti.com>
| * | TI: TNETV107X Fix Build ErrorChan-Taek Park2011-07-17-0/+6
| | | | | | | | | | | | | | | | | | | | | This patch provides SDRAM base address and initial stack address to fix build errors. Signed-off-by: Chan-Taek Park <c-park@ti.com>
| * | EfikaMX: Enable EXT2 bootingMarek Vasut2011-07-14-0/+1
| | | | | | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
| * | EfikaMX: Add missing CONFIG_SYS_TEXT_BASEJana Rapava2011-07-14-0/+2
| | | | | | | | | | | | Signed-off-by: Jana Rapava <fermata7@gmail.com>
| * | imx: Add support for zmx25 boardMatthias Weisser2011-07-14-0/+180
| | | | | | | | | | | | | | | | | | | | | zmx25 is a board based on imx25 SoC, 64 Megs of LPDDR, 32 Megs of NOR flash, an optional NAND flash. Signed-off-by: Matthias Weisser <weisserm@arcor.de>
| * | mx31pdk: cosmetic: Fix line over 80 charactersFabio Estevam2011-07-14-2/+4
| |/ | | | | | | Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | powerpc/p2041rdb: Add p2041rdb board supportMingkai Hu2011-07-17-0/+624
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P2041RDB Specification: ----------------------- Memory subsystem: * 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus) * 128 Mbyte NOR flash single-chip memory * 256 Kbit M24256 I2C EEPROM * 16 Mbyte SPI memory * SD connector to interface with the SD memory card Ethernet: * dTSEC1: connected to the Vitesse SGMII PHY (VSC8221) * dTSEC2: connected to the Vitesse SGMII PHY (VSC8221) * dTSEC3: connected to the Vitesse SGMII PHY (VSC8221) * dTSEC4: connected to the Vitesse RGMII PHY (VSC8641) * dTSEC5: connected to the Vitesse RGMII PHY (VSC8641) PCIe: * Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1 * Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2 SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces I2C: * I2C1: Real time clock, Temperature sensor, Memory module * I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2 UART: supports two UARTs up to 115200 bps for console Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/mpc8548cds: Remove incorrect DDR_MSYNC_IN erratum defineBecky Bruce2011-07-13-1/+0
|/ | | | | | | | This erratum doesn't exist on this processor, and the workaround spins on a non-existent register, causing boot to hang. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add default usb mode and phy type to hwconfigRamneek Mehresh2011-07-11-4/+13
| | | | | | | | | | | Move to use hwconfig for usb mode & phy type instead of magic 'usb_phy_type' environment variable on the following platforms: MPC8536DS, P1020RDB, P1020RDB-PC, P1010RDB, P2020RDB, P2020RDB-PC, P2020RDB, P3041DS, P4080DS, & P5020DS. Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/corenet_ds: add back buffer write for NOR flashYork Sun2011-07-11-0/+1
| | | | | | | | | Enable buffer write for better performance. This platform uses a NOR flash chip which supports write buffer programming. CFI driver can query the buffer size and use it to program the flash for best performance. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add basic support for P1023RDS boardRoy Zang2011-07-11-0/+562
| | | | | | | | | | | | | | The P1023RDS board is the reference board for the P1023 SoC. Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe, UART, I2C, etc. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Signed-off-by: Lei Xu <B33228@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add NAND boot support for P3041/P5020DSShaohui Xie2011-07-11-6/+23
| | | | | | | When booting from NAND we get the environment and FMan ucode from NAND. Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* qoriq/p1_p2_rdb: Add Dual Role USB support macro for P1020RDBRamneek Mehresh2011-07-11-0/+1
| | | | | | | Add CONFIG_HAS_FSL_DR_USB macro for P1020RDB Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-09-16 05:59:05 +0000