summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* powerpc/t2080rdb: Add T2080PCIe-RDB board supportShengzhou Liu2014-03-07-0/+779
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC. It works in two mode: standalone mode and PCIe endpoint mode. T2080PCIe-RDB Feature Overview ------------------------------ Processor: - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz DDR Memory: - Single memory controller capable of supporting DDR3 and DDR3-LP devices - 72bit 4GB DDR3-LP SODIMM in slot Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - Two 10Gbps SFP+ ports on-board - Two 10Gbps Base-T ports on-board Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC SerDes 16 lanes configuration: - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10) - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2) - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3) - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2) - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2) - SerDes-2 Lane G-H: to SATA1 & SATA2 IFC/Local Bus: - NOR: 128MB 16-bit NOR flash - NAND: 512MB 8-bit NAND flash - CPLD: for system controlling with programable header on-board eSPI: - 64MB N25Q512 SPI flash USB: - Two USB2.0 ports with internal PHY (both Type-A) PCIe: - One PCIe x4 gold-finger - One PCIe x4 connector - One PCIe x2 end-point device (C293 Crypto co-processor) SATA: - Two SATA 2.0 ports on-board SDHC: - support a TF-card on-board I2C: - Four I2C controllers. UART: - Dual 4-pins UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t208xqds: fixup for t208xqdsShengzhou Liu2014-03-07-1/+1
| | | | | | | | Change QIXIS timing parameter CONFIG_SYS_CS3_FTIM2 to 8 from 0. Fix EMI2 for t2080qds, which was caused by adding t2081qds. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini2014-03-04-26/+0
|\
| * mtd: nand: omap: remove unused #defines from common omap_gpmc.hpekon gupta2014-03-04-26/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI params or nand_id[] table. And based on that it defines ECC layout. This patch 1) removes following board configs used for defining NAND ECC layout - GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND) - GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND) - GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND) - GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND) 2) removes unused #defines in common omap_gpmc.h depending on above configs Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5 Signed-off-by: Pekon Gupta <pekon@ti.com>
* | sandbox: Convert GPIOs to use driver modelSimon Glass2014-03-04-0/+1
| | | | | | | | | | | | Convert sandbox over to use driver model GPIOs. Signed-off-by: Simon Glass <sjg@chromium.org>
* | dm: Add a demonstration/example driverSimon Glass2014-03-04-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As an example of how to write a uclass and a driver, provide a demo version of each, accessible through the 'demo' command. To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO. The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and CONFIG_DM_DEMO_SHAPE. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com> Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com> Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
* | dm: Add a 'dm' command for testingSimon Glass2014-03-04-0/+1
| | | | | | | | | | | | | | | | | | | | | | This command is not required for driver model operation, but can be useful for testing. It provides simple dumps of internal data structures. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com> Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com> Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
* | dm: Add basic testsSimon Glass2014-03-04-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add some tests of driver model functionality. Coverage includes: - basic init - binding of drivers to devices using platform_data - automatic probing of devices when referenced - availability of platform data to devices - lifecycle from bind to probe to remove to unbind - renumbering within a uclass when devices are probed/removed - calling driver-defined operations - deactivation of drivers when removed - memory leak across creation and destruction of drivers/uclasses - uclass init/destroy methods - automatic probe/remove of children/parents when needed This function is enabled for sandbox, using CONFIG_DM_TEST. Signed-off-by: Simon Glass <sjg@chromium.org>
* | sandbox: config: Enable driver modelSimon Glass2014-03-04-0/+1
| | | | | | | | | | | | Use driver model in sandbox to permit running of driver model unit test. Signed-off-by: Simon Glass <sjg@chromium.org>
* | sandbox: Build a device tree file for sandboxSimon Glass2014-03-04-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Add support for building a device tree for sandbox's CONFIG_OF_HOSTFILE option to make it easier to use device tree with sandbox. This adjusts the Makefile to build a u-boot.dtb file which can be passed to sandbox U-Boot with: ./u-boot -d u-boot.dtb Signed-off-by: Simon Glass <sjg@chromium.org>
* | sizes.h - consolidate for all architecturesAlexey Brodkin2014-03-04-28/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Copied from Linux sources "include/linux/sizes.h" commit 413541dd66d51f791a0b169d9b9014e4f56be13c Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Stefan Roese <sr@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Tom Rini <trini@ti.com> Acked-by: Stefan Roese <sr@denx.de> [trini: Add bcm Kona platforms to the patch] Signed-off-by: Tom Rini <trini@ti.com>
* | zynq: Do not use SPL OF initializationMichal Simek2014-03-04-0/+1
|/ | | | | | Disable CONFIG_OF_CONTROL for SPL compilation. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-26-43/+1077
|\ | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/armv7/config.mk board/ti/am43xx/mux.c include/configs/am43xx_evm.h Signed-off-by: Tom Rini <trini@ti.com>
| * Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-02-24-12/+849
| |\
| | * omap4_common: config: remove I2C for SPL modeNishanth Menon2014-02-21-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 6789e84ecaa8f45d053084e08c381284a04abff7 (i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework) intended to make I2C driver compatible with latest changes. It unfortunately has had a impact on size on SPL as well. For example on SDP4430, 32032 bytes before/MLO 35416 bytes after/MLO With this mentioned commit, MLO stops booting on SDP4430 as only 32K is accessible for non-secure (bootloader) s/w on GP devices and the size increase to 56K fails boot. On the latest u-boot commit e7be18225fbea76d1f0034b224f0d1e60f07cfcf, MLO is now at size 35592 bytes, However, I2C is not necessary for SPL to function as we use SR_I2C for controlling the PMIC. Disabling I2C reduces MLO to 32224 bytes which allows OMAP4 GP platform to boot up. Since this is common for all OMAP4 platforms, remove the need for I2C for SPL builds in the common config. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Sricharan R <r.sricharan@ti.com>
| | * dra7xx_evm: Enable GPT commandsTom Rini2014-02-21-0/+11
| | | | | | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| | * am43xx_evm: Enable GPT commandsTom Rini2014-02-21-0/+9
| | | | | | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| | * am335x_evm: Enable GPT commandsTom Rini2014-02-21-0/+12
| | | | | | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| | * arm: omap: cm_t35: Remove CONFIG_SYS_BOOTMAPSZ to fix FDT Linux bootingStefan Roese2014-02-21-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With CONFIG_SYS_BOOTMAPSZ defined, recent Linux kernel booting results in this error: Booting using the fdt blob at 0x81f00000 Loading Kernel Image ... OK ERROR: Failed to allocate 0x1189d bytes below 0x80004000. device tree - allocation error FDT creation failed! hanging...### ERROR ### Please RESET the board ### Removing this define solves this issue. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@ti.com>
| | * OMAP3: fix default environment for mcx boardStefano Babic2014-02-21-4/+3
| | | | | | | | | | | | | | | | | | Patch allows to load a script at the startup from MMC. Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * OMAP3: add missing gpio clock init and fix NAND SPL for mcx boardStefano Babic2014-02-21-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Patch contains the same fixes as commit 4b9b2c300a23ca4a85811918dc92e822a9571a87 (missing CONFIG_OMAP3_GPIO_2) and commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30 (missing CONFIG_SPL_NAND_SOFTECC). Same issues are relevant for the mcx board, too. Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * arm: omap3: Fix tao3530/omap3_ha SPL boot hangup (GPIO clocks not enabled)Stefan Roese2014-02-21-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Patch f33b9bd3 [arm: omap3: Enable clocks for peripherals only if they are used] breaks SPL booting on tao3530. Since some gpio input's are read to detect the board revision. But with this patch above, the clocks to the GPIO subsystems are not enabled per default any more. The GPIO banks need to be configured specifically now. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
| | * Add support for B&R KWB MotherboardHannes Petermaier2014-02-21-0/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC. Most of code is derived from TI's AM335x_EVM Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at> Cc: trini@ti.com
| | * board: Add support for B&R T-Series MotherboardHannes Petermaier2014-02-21-0/+462
| | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for Bernecker & Rainer Industrieelektronik GmbH T-Series Motherboard, using TI's AM3352 SoC. Most of code is derived from TI's AM335x_EVM Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
| | * am335x: Initial support for Silica Pengwyn boardLothar Felten2014-02-21-1/+209
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add support for the Silica Pengwyn board [1] The board is based on a TI AM3354 CPU [2] All jumpers removed it will boot from the SDcard, the console is on UART1 accessible via the FDTI -> USB. The on board NAND flash is supported and can act as boot medium, depending on jumper settings. USB Host, USB Device and Ethernet are also provided but untested. [1] http://www.silica.com/product/silica-pengwyn-board.html [2] http://www.ti.com/product/am3354 Signed-off-by: Lothar Felten <lothar.felten@gmail.com> [trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused spi0_pin_mux from Pengwyn support] Signed-off-by: Tom Rini <trini@ti.com>
| * | board: bcm28155_ap: Add board filesDarwin Rambo2014-02-22-0/+140
| | | | | | | | | | | | | | | | | | | | | | | | Add support for the bcm28155_ap reference board. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com> Reviewed-by: Tim Kryger <tkryger@linaro.org>
| * | ARM: rpi_b: rework boot scripts, enable sysbootStephen Warren2014-02-22-15/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as much as possible. This will aid in a future patch which will create a common header e.g. config_distro_bootcmd.h. While at it, enable booting from extlinux.conf using the sysboot command. The iteration and componentization currently makes a little more sense for Tegra than RPi, but I'd still like to keep the two as similar as possible. USB and networking support is coming to the RPi in due course, and it'll all make more sense then anyway. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
| * | ARM: rpi_b: load /uEnv.txt from MMC at startupStephen Warren2014-02-21-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Pi has no flash to store an environment in the usual fashion. However, the user may wish to customize the environment. We know that the SD card must be present, since that's where the boot ROM has loaded U-Boot from. So, load uEnv.txt from there early during boot. This allows the user to e.g. customize boot_targets, in order to automatically select network boot. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
| * | ARM: rpi_b: convert to use distro defaultsStephen Warren2014-02-21-16/+13
| |/ | | | | | | | | | | | | | | Modify the rpi_b board to include the "distro defaults" header, so that all the config options distros expect are enabled. Remove any #defines that enable the same options from the rpi_b.h. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-02-25-43/+194
|\ \ | | | | | | | | | | | | | | | | | | With this, fixup a trivial build error of get_effective_memsize needing to be updated in the new board/freescale/p1010rdb/spl.c Signed-off-by: Tom Rini <trini@ti.com>
| * | powerpc/mpc8536DS:Increase binary size for mpc8536DS boardHaijun.Zhang2014-02-24-7/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | u-boot binary size for Freescale mpc8536DS platforms is 512KB. This has been reached to upper limit of the platforms and causig linker error. So increase the u-boot binary size to 768KB. Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | powerpc: p1010rdb: Enable p1010rdb to start from NAND/SD/SPI flash with SPLYing Zhang2014-02-24-9/+147
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the previous patches, we introduced the SPL/TPL fraamework. For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The SPL was loaded by the code from the internal on-chip ROM. The SPL initializes the DDR according to the SPD and loads the final uboot image into DDR, then jump to the DDR to begin execution. For NAND booting way, the nand SPL has size limitation on some board(e.g. P1010RDB), it can not be more than 8KB, we can call it "minimal SPL", So the dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD and loads the final uboot image into DDR,then jump to the DDR to begin execution. This patch enabled SPL/TPL for P1010RDB to support starting from NAND/SD/SPI flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL. Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to execute, so the section .resetvec is no longer needed. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | SPL: P1022DS: fix the problem booting from spi flashYing Zhang2014-02-24-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | There was no enough memory for malloc in SPL booting from spi flash, so relayout the memory in SPL: reduce the memory for global data from 16K Bytes to 4K Bytes, save the space for malloc. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | SPL: P2020RDB: fix the problem booting from spi flashYing Zhang2014-02-24-4/+8
| | | | | | | | | | | | | | | | | | | | | | | | There was no enough stack in SPL, so the buffer needed in SPL is to malloc from memory pool and to repalce the temporary variable. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | SPL: powerpc: expand SPL's length to 128KYing Zhang2014-02-24-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | 1. The SPL's length of SDCARD boot has not enough,expand the SPL's length to 128K. 2. deleted unused symbol: CONFIG_SYS_RUN_INDDR Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | powerpc/t2081qds: Add T2081 QDS board supportShengzhou Liu2014-02-24-8/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T2081 QDS is a high-performance computing evaluation, development and test platform supporting the T2081 QorIQ Power Architecture processor. T2081QDS board Overview ----------------------- - T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz - 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC) - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving - Ethernet interfaces: - Two on-board 10M/100M/1G bps RGMII ports - Two 10Gbps XFI with on-board SFP+ cage - 1Gbps/2.5Gbps SGMII Riser card - 10Gbps XAUI Riser card - Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC - SerDes: - 8 lanes up to 10.3125GHz - Supports SGMII, HiGig, XFI, XAUI and Aurora debug, - IFC: - 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - eSPI: - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040) - USB: - Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - PCIe: - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) - eSDHC: - Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and voltage translators - I2C: - Four I2C controllers. - UART: - Dual 4-pins UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | kbuild: Move linker sciript check to prepare1Masahiro Yamada2014-02-25-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Same as the previous commit. Move sanity check to prepare1 target to avoid nasty troubles. Before this commit, LDSCRIPT existence was not checked when it was specified by CONFIG_SYS_LDSCRIPT. Now LDSCRIPT existence is checked for all boards. $(wildcard $(LDSCRIPT)) must point to the linker scripts with absolute path. Otherwise, make will terminate with a false error on out-of-tree build. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | arm: delete unused macro CONFIG_ARCH_DEVICE_TREEMasahiro Yamada2014-02-24-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Rajeshwari Birje <rajeshwari.s@samsung.com> Cc: Inderpal Singh <inderpal.singh@linaro.org>
* | | Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2014-02-21-0/+20
|\ \ \
| * | | am437x_epos_evm: add SPL API, QSPI, and serial flash supportSourav Poddar2014-02-18-0/+20
| |/ / | | | | | | | | | | | | | | | | | | | | | Enables support for SPI SPL, QSPI and Spansion serial flash device on the EVM. Configures pin muxes for QSPI mode. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* | | axs101: change command prompt marker to match marketing name of the boardAlexey Brodkin2014-02-21-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Proper spelling of the boad marketing name is with upper case. So changing it from lower case to upper case here. Cc: Tom Rini <trini@ti.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-02-20-1186/+209
|\ \ \ | | |/ | |/|
| * | Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2014-02-20-248/+9
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: Makefile drivers/net/npe/Makefile These two conflicts arise from commit 0b2d3f20 ("ARM: NET: Remove the IXP NPE ethernet driver") and are resolved by deleting the drivers/net/npe/Makefile file and removing the CONFIG_IXP4XX_NPE line from Makefile.
| * \ \ Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2014-02-19-104/+122
| |\ \ \
| | * \ \ Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2014-02-11-2032/+470
| | |\ \ \
| | * | | | mx6: Enable L2 cache supportFabio Estevam2014-02-11-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add L2 cache support and enable it by default. Configure the L2 cache in the same way as done by FSL kernel: http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Dirk Behme <dirk.behme@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | | | mx6sl: Adjust fdt_addr to avoid address overlappingFabio Estevam2014-02-11-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Similarly as it was done on commit 6584a1b526 (ARM: mx6: Change the FDT loading address to avoid overlaping), we need to adjust the fdt_addr in order to be able to boot FSL 3.10 kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| | * | | | vf610twr: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
| | * | | | udoo: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
| | * | | | mx6slevk: Set default environment to use zImageOtavio Salvador2014-02-11-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
generated by cgit v1.1 at 2024-11-06 13:56:43 +0000