summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* ppc4xx: Add CONFIG_PCI_4xx_PTM_OVERWRITE to some esd 4xx boardsMatthias Fuchs2009-09-10-0/+12
| | | | | Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* amcc-common.h: Use filenames from environment variables for update procedure.Detlev Zundel2009-09-10-3/+5
| | | | | | | | | | Using a separate "u-boot" environment variable allows to easily specify different filenames for the update procedure. This is also in line with many other board configurations defining an "update" script. Signed-off-by: Detlev Zundel <dzu@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk2009-09-07-0/+1
|\
| * Reset i2c slave devices during init on mpc5xxx cpusEric Millbrandt2009-09-06-0/+1
| | | | | | | | | | | | | | | | | | | | | | Reset any i2c devices that may have been interrupted during a system reset. Normally this would be accomplished by clocking the line until SCL and SDA are released and then sending a start condtiion (From an Atmel datasheet). There is no direct access to the i2c pins so instead create start commands through the i2c interface. Send a start command then delay for the SDA Hold time, repeat this by disabling/enabling the bus a total of 9 times. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2009-09-07-0/+1107
|\ \ | |/ |/|
| * ARM: DaVinci: Adding Support for DaVinci DM365 EVMSandeep Paulraj2009-09-05-0/+182
| | | | | | | | | | | | | | This patch adds support for the DM365 EVM. It has been tested on a DM365 EVM. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * Add support for the DevKit8000 boardFrederik Kriewitz2009-09-05-0/+307
| | | | | | | | | | | | This patch adds support for the DevKit8000 board. Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
| * Support for the Calao TNY-A9260/TNY-A9G20 boardsAlbin Tonnerre2009-09-01-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by Calao Systems <http://www.calao-systems.com>. Their components are very similar to the AT91SAM9260EK board, so their configuration is based on the configuration of this board. There are however some differences: different clocks, no LCD, no ethernet. They also can use SPI EEPROM to store the environment. Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * Add support for the Calao SBC35-A9G20 boardAlbin Tonnerre2009-09-01-0/+194
| | | | | | | | | | | | | | | | | | | | | | The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems <http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND flash, two USB host ports, and an USB device port. More informations can be found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936> Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
| * imx27lite: add support for imx27lite board from LogicPDIlya Yanok2009-09-01-0/+252
| | | | | | | | | | | | | | | | | | This patch adds support for i.MX27-LITEKIT development board from LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND flash, FEC ethernet controller integrated into i.MX27. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Acked-by: Wolfgang Denk <wd@denx.de>
* | galaxy5200: Add chip select region for an Epson S1D15313Eric Millbrandt2009-09-04-0/+5
| | | | | | | | Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
* | Add PCI support to eNET boardGraeme Russ2009-09-04-7/+7
| | | | | | | | Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | Misc sc520 cdp fixupsGraeme Russ2009-09-04-22/+0
| | | | | | | | | | | | | | Now that the PCI, SATA et al compile problems have been resolved, the cludge that was applied to avoid them can be removed Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | Fixup sc520_spunk boardGraeme Russ2009-09-04-0/+2
| | | | | | | | | | | | | | | | Primary intent is to resolve build errors for this board which has been neglected for a very long time. I do not have one of these boards, so I cannot test functionality Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | i386: Misc PCI fixupsGraeme Russ2009-09-04-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY (Originally done in commit ff4e66e93c1a, regressed by commit 6d7f610b09f8) Cast PCI_ROM_ADDRESS_MASK to u32 Wrap probe_pci_video() call inside #ifdef CONFIG_VIDEO Change call to pci_find_class() to pci_find_devices(). This is based on a patch submitted on 1st March 2007 (Patch that fixes the compilation errors for sc520_cdp board) by mushtaq_k This patch requires that PCI_VIDEO_VENDOR_ID and PCI_VIDEO_DEVICE_ID be specified in the board config file. Dummy values have been added for the SC520 CDP board to enable compilation, but since I do not have one of these, I do know what the values should be Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | Fix environment configuration for eNET boardGraeme Russ2009-09-04-6/+5
| | | | | | | | | | | | | | | | The current configuration of the Environment has the redundant copy of the environment in the Boot Flash - This was never the intent. The Environment should instead be in the first two sectors of the first Strata Flash Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* | Blackfin: enable 64bit printf for nandMike Frysinger2009-09-02-0/+3
| | | | | | | | | | | | | | | | Since the NAND code now uses 64bit code, make sure we enable support for ADI Blackfin boards in printf to avoid the warning: nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output! Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf537u: new board portHarald Krapfenbauer2009-09-02-0/+150
| | | | | | | | | | | | | | | | The CM-BF537U is similar to the CM-BF537E module, but enough to need its own board port. Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: enable more network commands for ADI dev boardsRobin Getz2009-09-02-0/+10
| | | | | | | | | | | | | | | | Add dns and ntp to default networking commands, and ask for more dhcp options to better configure the network environment. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf537-stamp: comment CF-Flash Card Support betterMichael Hennerich2009-09-02-5/+24
| | | | | | | | | | Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: use +(filesize) to make sure we are only doing what is necessaryRobin Getz2009-09-02-2/+2
|/ | | | | Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'next' of ../nextWolfgang Denk2009-08-31-94/+1153
|\
| * 85xx: Added PCIe support for P1 P2 RDBPoonam Aggrwal2009-08-28-0/+6
| | | | | | | | | | | | | | Call fsl_pci_init_port() to initialize all the PCIe ports on the board. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Fix memory test range on MPC8536DSFelix Radensky2009-08-28-2/+2
| | | | | | | | | | | | | | | | | | | | With current values of CONFIG_SYS_MEMTEST_START and CONFIG_SYS_MEMTEST_END memory test hangs if run without arguments. Set them to sane values, so that all available 512MB of RAM excluding exception vectors at the bottom and u-boot code and stack at the top can be tested. Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Removed BEDBUG support on P1_P2_RDBKumar Gala2009-08-28-1/+0
| | | | | | | | | | | | To match all other 85xx platforms we are removing BEDBUG support. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Add support for P2020RDB boardPoonam Aggrwal2009-08-28-0/+556
| | | | | | | | | | | | | | | | | | | | | | | | | | The code base adds P1 & P2 RDB platforms support. The folder and file names can cater to future SOCs of P1/P2 family. P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series. Tested following on P2020RDB: 1. eTSECs 2. DDR, NAND, NOR, I2C. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 8xxx: Removed CONFIG_NUM_CPUS from 85xx/86xxPoonam Aggrwal2009-08-28-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | The number of CPUs are getting detected dynamically by checking the processor SVR value. Also removed CONFIG_NUM_CPUS references from all the platforms with 85xx/86xx processors. This can help to use the same u-boot image across the platforms. Also revamped and corrected few Freescale Copyright messages. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Remove unused CONFIG_CLEAR_LAW0 definesPeter Tyser2009-08-28-3/+0
| | | | | | | | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Add a 36-bit physical configuration for MPC8536DSKumar Gala2009-08-28-10/+72
| | | | | | | | | | | | | | | | | | | | We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary to allow for larger memory sizes. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * pci/fsl_pci_init: Rework PCI ATMU setup to handle >4G of memoryKumar Gala2009-08-28-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The old PCI ATMU setup code would just mimic the PCI regions into the ATMU registers. For simple memory maps in which all memory, MMIO, etc space fit into 4G this works ok. However there are issues with we have >4G of memory as we know can't access all of memory and we need to ensure that PCICSRBAR (PEXCSRBAR on PCIe) isn't overlapping with anything since we can't turn it off. We first setup outbound windows based on what the board code setup in the pci regions for MMIO and IO access. Next we place PCICSRBAR below the MMIO window. After which we try to setup the inbound windows to map as much of memory as possible. On PCIe based controllers we are able to overmap the ATMU setup since RX & TX links are separate but report the proper amount of inbound address space to the region tracking to ensure there is no overlap. On PCI based controllers we use as many inbound windows as available to map as much of the memory as possible. Additionally we changed all the CCSR register access to use proper IO accessor functions. Also had to add CONFIG_SYS_CCSRBAR_PHYS to some 86xx platforms that didn't have it defined. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * Merge branch 'next' of git://git.denx.de/u-boot-nand-flash into nextWolfgang Denk2009-08-28-0/+6
| |\
| | * 83xx, kmeter1: added NAND supportHeiko Schocher2009-08-26-0/+6
| | | | | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | galaxy5200: Cleanup typo and trailing whitespaceEric Millbrandt2009-08-26-4/+4
| |/ | | | | | | Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
| * Merge branch 'next' of git://git.denx.de/u-boot-net into nextWolfgang Denk2009-08-25-59/+82
| |\
| | * Convert CS8900 Ethernet driver to CONFIG_NET_MULTI APIBen Warren2009-08-25-59/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All in-tree boards that use this controller have CONFIG_NET_MULTI added Also: - changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900 - changed CS8900_BASE to CONFIG_CS8900_BASE - changed CS8900_BUS?? to CONFIG_CS8900_BUS?? - cleaned up line lengths - modified VCMA9 command function that accesses the device - removed MAC address initialization from lib_arm/board.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Tested-by: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
| | * arm nomadik: activate defrag choose 4k transfer block sizeAlessandro Rubini2009-08-25-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | This chooses 4kB data size for both TFTP and NFS, as an example about how to use support for IP fragments. Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | Merge branch 'master' into nextWolfgang Denk2009-08-25-2/+2
| |\ \ | | |/ | |/|
| * | Add support for the galaxy5200Eric Millbrandt2009-08-25-0/+428
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the DEKA Research and Development galaxy5200 board The galaxy5200 is an Freescale mpc5200 based embedded industrial control board. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
| * | unify {CONFIG_,}ENV_IS_EMBEDDEDMike Frysinger2009-08-25-13/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some boards have fallen out of sync by defining CONFIG_ENV_IS_EMBEDDED manually. While it is useful to have this available to the build system, let's do it automatically rather than forcing people to opt into it. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | Use common code for Matrix Vision boardsAndré Schwarz2009-08-28-30/+21
| | | | | | | | | | | | | | | | | | | | | Clean up existing boards (mvBC-P/MPC5200 and mvBL-M7/MPC8343) by using common code. Signed-off-by: André Schwarz <andre.schwarz@matrix-vision.de>
* | | mpc83xx: mpc8349itx - accommodate larger kernel sizes & unzero the bootdelayKim Phillips2009-08-26-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | apparently the ITX was missed last round. Also make bootdelay consistent with other boards, so as to give on the opportunity to fix mistakenly set bootcmd without having checked for an bootdelay zero setting first. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | | mpc83xx: match dtb filename references to their dts equivalents in the linux ↵Kim Phillips2009-08-26-2/+2
| |/ |/| | | | | | | | | kernel Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | Blackfin: cm-bf527/cm-bf537: increase flash sectorsHarald Krapfenbauer2009-08-23-2/+2
|/ | | | | | | | Newer revisions of these boards have slightly larger flashes, so increase the configured number of sectors so that U-Boot works on all revisions. Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2009-08-22-36/+37
|\
| * mpc83xx: accommodate larger kernel sizes by defaultKim Phillips2009-08-21-20/+20
| | | | | | | | | | | | | | linux mpc83xx_defconfig kernels are getting bigger, accommodate for their growth by adjusting default load and fdt addresses. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * mpc83xx: mpc8377erdb - change DDR settings to those from latest bspKim Phillips2009-08-21-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | when using Linus' 83xx_defconfig, the mpc8377rdb would hang at boot at either: NET: Registered protocol family 16 or the io scheduler cfq registered message. Fixing up these DDR settings appears to fix the problem. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * mpc83xx: tqm8349 - remove pci & flash window conflictKim Phillips2009-08-21-1/+1
| | | | | | | | | | | | | | | | | | | | | | commit 9993e196da707a0a1cd4584f1fcef12382c1c144 "mpc83xx: convert all remaining boards over to 83XX_GENERIC_PCI" remapped pci windows on tqm834x to make it more consistent with the other 83xx boards. During that time however, the author failed to realize that FLASH_BASE was occupying the same range as what PCI1_MEM_BASE was being assigned. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Tested-by: Wolfgang Denk <wd@denx.de>
| * mpc83xx: mpc8349 - delete unused SYS_MID_FLASH_JUMPPaul Gortmaker2009-08-21-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This was introduced with the MPC8349EMDS board, and then copied to a couple other boards by nature of being the reference implementation. u-boot$git grep CONFIG_SYS_MID_FLASH_JUMP include/configs/MPC8349EMDS.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000 include/configs/sbc8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000 include/configs/vme8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000 u-boot$ It currently isn't used, so delete it before it spreads further. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * mpc83xx: sbc8349 - make enabling PCI more user friendlyPaul Gortmaker2009-08-21-9/+13
| | | | | | | | | | | | | | | | | | | | Prior to this commit, to enable PCI, you had to go manually edit the board config header, which isn't really user friendly. This adds the typical PCI make targets to the toplevel Makefile in accordance with what is being done with other boards. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | arm: rd6281a: Fixed NAND specific warningPrafulla Wadaskar2009-08-21-0/+1
|/ | | | | | | It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF for NAND specific warning removal, same is done in this patch Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
generated by cgit v1.1 at 2024-11-07 11:46:15 +0000