summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* devkit8000: Implement and activate direct OS bootSimon Schwarz2012-03-27-2/+5
| | | | | | | | | | - Implements spl_start_uboot() for devkit8000 - Add configs to activate direct OS boot from SPL Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* devkit8000: add config for spl commandSimon Schwarz2012-03-27-0/+8
| | | | | | | | | This adds some configs for devkit8000 to use the new spl command Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* configs: imx: Use CONFIG_SF_DEFAULT_CSFabio Estevam2012-03-27-3/+3
| | | | | | | | | | CONFIG_SPI_FLASH_CS is not used anywhere. Use CONFIG_SF_DEFAULT_CS instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx28evk: Provide default values for SPI bus and chip selectFabio Estevam2012-03-27-0/+2
| | | | | | | | | | Provide default values for SPI bus and chip select. This allows the command "sf probe" to work without passing SPI bus and chip select numbers as arguments. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
* i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITEEric Nelson2012-03-27-0/+2
| | | | | | Allow non-dt kernels to boot Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAGEric Nelson2012-03-27-0/+1
| | | | | | | | | | | | | | This is needed to support Freescale-supplied userspaces. At the moment, both the IPU and VPU libraries provided by Freescale in the "imx-lib" package contain routines which scrape the system revision from /proc/cpuinfo. In the VPU library, this information is used to load the proper firmware, allowing a single binary to be used across various i.MX processors. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx31pdk: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-27-1/+1
| | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* efikamx: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-27-1/+1
| | | | | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Cc: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Marek Vasut <marek.vasut@gmail.com>
* mx53smd: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-27-1/+1
| | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53evk: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-27-1/+1
| | | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx51evk: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-27-1/+1
| | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* i.MX6: mx6qsabrelite: add ext2 supportEric Nelson2012-03-27-0/+1
| | | | | | Current Ubuntu releases from Freescale contain a boot script in ext3 filesystem. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}Marek Vasut2012-03-26-0/+12
| | | | | | | | | These symbols are no longer defined in Linux-ARM's mach-types files. Replace these with CONFIG_MACH_TYPE instead. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* SPL: Enable YMODEM support on BeagleBone and AM335x EVMMatt Porter2012-03-26-0/+1
| | | | | | Cc: Chandan Nath <chandan.nath@ti.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Matt Porter <mporter@ti.com>
* mx6qsabrelite: add and enable USB Host 1 supportWolfgang Grandegger2012-03-26-0/+13
| | | | | | Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <jason.hui@linaro.org> Signed-off-by: Wolfgang Grandegger <wg@denx.de>
* zipitz2: use pxa_mmc_gen as MMC driverVasily Khoruzhick2012-03-26-2/+4
| | | | Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
* zipitz2: fix boot issue introduced by PXA low level init reworkVasily Khoruzhick2012-03-26-1/+7
| | | | | | | | CONFIG_SYS_INIT_SP_ADDR points to RAM, but it's used before DRAM controller init. Fix it by setting CONFIG_SYS_INIT_SP_ADDR to SRAM Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
* Armada100: gplugD: Add FAT & EXT2 command supportAjay Bhargav2012-03-19-0/+2
| | | | | | This patch adds FAT and ext2 command support for marvell gplugD Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* Armada100: gplugD: Add USB command supportAjay Bhargav2012-03-19-0/+12
| | | | | | | This patch adds support for USB commands and USB storage device for Marvell gplugD Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* USB:gadget:designware USB device controller (UDC) implementationVipin KUMAR2012-03-19-1/+3
| | | | | | | | | | The earlier usb device controller driver was specific to spear platforms. This patch implements the usb device controller driver as a generic controller which can be reused by other platforms using this peripheral. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Marek Vasut <marex@denx.de>
* CPCI750: Add CPCI-HD/2 supportReinhard Arlt2012-03-18-8/+11
| | | | | | | | This patch adds support for the esd CPCI-HD/2 board to u-boot for CPCI-CPU/750. As the primary devices on the CPCI-HD/2 board are connected to device 1 and 3, the device must be swapped. Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
* Merge branch 'master' of git://git.denx.de/u-boot-avr32Wolfgang Denk2012-03-17-10/+26
|\ | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-avr32: atmel_mci.h: remove outdated register macros doc/git-mailrc: add <me> to avr32 alias ATMEL: remove old atmel_mci driver ATMEL: use generic mmc framework
| * ATMEL: use generic mmc frameworkSven Schnelle2012-03-13-10/+26
| | | | | | | | | | | | | | | | | | gen_atmel_mci works on AVR32 as well, so no need to use the legacy mmc driver. This also has the nice side effect of being able to use SDHC cards an those boards. Signed-off-by: Sven Schnelle <svens@stackframe.org> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | Merge branch 'sandbox' of git://git.denx.de/u-boot-blackfinWolfgang Denk2012-03-17-0/+10
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'sandbox' of git://git.denx.de/u-boot-blackfin: sandbox: mark os_exit as noreturn sandbox: add getopt support sandbox: allow processing before main loop sandbox: add concept of sandbox state sandbox: disable fortification sandbox: u-boot.lds: tweak style sandbox: add get_{tbclk,ticks} sandbox: enable GPIO driver sandbox: gpio: add basic driver for simulating GPIOs sandbox: add flags for open() call sandbox: config: enable fdt and snprintf() options sandbox: fdt: add support for CONFIG_OF_CONTROL sandbox: add lseek helper sandbox: add ifdef protection to os.h sandbox: add required header to os.c sandbox: sort header files in os.c
| * | sandbox: enable GPIO driverSimon Glass2012-03-12-0/+4
| | | | | | | | | | | | | | | | | | | | | Enable the new GPIO driver for sandbox. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * | sandbox: config: enable fdt and snprintf() optionsSimon Glass2012-03-12-0/+6
| |/ | | | | | | | | | | | | Enable fdt code and safe snprintf() options for sandbox. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | sh: Fix sh7264 clock speed and related serial settingPhil Edworthy2012-03-08-1/+1
| | | | | | | | | | | | | | | | The generalised calculation of the serial bit rate reg also applies to sh7264, it was just the clock speed that was set incorrectly. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | sh: ecovec: Add support PHY of SMSCNobuhiro Iwamatsu2012-03-08-0/+1
|/ | | | | Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* tt01: fix hush parser config, add release configHelmut Raiger2012-02-27-3/+8
| | | | | | | Add PREBOOT, SILENT_CONSOLE and DEVICE_NULLDEV for release build. Fixed bug in CONFIG_SYS_HUSH_PARSER define. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* tt01: add video supportHelmut Raiger2012-02-27-1/+28
| | | | | | | | The video setup for the Epson display is provided. Addtionally some extra info is displayed next to the Linux logo. Make get_cpu_rev() publicly available (added to sys_proto.h). Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* tt01: fix environment sizeHelmut Raiger2012-02-27-1/+1
| | | | | | size of environment must match erasable block size in the flash. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* i.mx6q: mx6qsabrelite: Update the network configurationTroy Kisky2012-02-27-0/+2
| | | | | | | | | | | | | | | | | | | Define CONFIG_PHY_MICREL, and minimize the tx clock delay. There is an issue with 1000 baseTx mode on early revs of the SabreLite boards. The center tap pin 9 of the mag RJ45 USB combo was connected to the 3.3 filtered supply. Letting this pin float solved the problem. Symptoms of the problem were packets with many extra zeroes tacked on the end, and random bit flips causing a high rate of CRC errors. 10/100 baseTx worked fine on all revs. To disable 1000 baseTx for these boards, simply define the environment variable disable_giga. ie. setenv disable_giga 1 Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
* integrator: update the Integrator/CP configLinus Walleij2012-02-27-34/+13
| | | | | | | | | | | | | | | | | | | The Integrator/CP config file was very outdated and gives a non functional U-Boot. So: - Set the CONFIG_ARCH_CINTEGRATOR arch flag correctly - Add proper core module configuration options - Skip cluttered command lista and just include <config_cmd_default.h> - Kill off #if 0 network section and insert some example configuration that simply just boots from the network using TFTP if available. - Delete flash control registers that have no business in this config file. These are already moved down to board/armltd/integrator/integrator-sc.h Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* integrator: rewrite the AP PCI driverLinus Walleij2012-02-27-142/+6
| | | | | | | | | | | | | | | | | | | | | | | | | The PCI support for the Integrator AP has apparently never been finished and I strongly suspect that it has never worked, so let's fix it. This is a list of the more or less un-splittable changes done in this driver rewrite: - Replace the register definitions stashed into the config file (!) with a copy if the register file from the Linux kernels arch/arm/include/asm/hardware/pci_v3.h - Delete the unreadable gigantic macros that perform the config accesses and replace them with copyedited code from Linux arch/arm/mach-integrator/pci_v3.c - Rewrite the rest of the setup code to use the v3_[read|write][lwb]() accessors. - Enable PCI by default in the AP board configuration. - Fix checkpatch warnings and make code more conformant. Tested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* mcx: Enable command line editingDetlev Zundel2012-02-27-0/+2
| | | | | Signed-off-by: Detlev Zundel <dzu@denx.de> CC: Stefano Babic <sbabic@denx.de>
* dm6467Tevm: Use a common configuration file for davinci_dm6467evm and ↵prabhakar.csengg@gmail.com2012-02-27-168/+0
| | | | | | | | | | | | | | | | | | | | davinci_dm6467Tevm In commit 2d575e46859dd9127a9cec731ace77523e6ea2ab a separate header file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h. The substantial difference between the davinci_dm6467evm and the davinci_dm6467Tevm configuration is a single bit in the hardware revision that is passed to the Linux kernel and davinci_dm6467evm has REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a REFCLK_FREQ = 33000000. This patch removes include/configs/davinci_dm6467Tevm.h. Instead the include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined in boards.cfg. Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com> Cc: Tom Rini <trini@ti.com>
* OMAP3: Remove unused CONFIG_SYS_NAND_ECCSTEPS/TOTALThomas Weber2012-02-27-14/+0
| | | | Signed-off-by: Thomas Weber <weber@corscience.de>
* Tricorder: Switch env to generic mmc driverThomas Weber2012-02-27-3/+4
| | | | | | | | Because the tricorder uses the CONFIG_OMAP_HSMMC the initialization command is mmc rescan and not mmc init. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tom Rini <trini@ti.com>
* mx6q: mx6qsabrelite: Conditionally define macros for environment in serial flashEric Nelson2012-02-27-3/+15
| | | | | | | | | | | | | | | | | | | | | | The default settings store the persistent environment on SD card and not serial flash (SPI NOR). To use SPI NOR to save the environment instead of SD card, edit include/configs/mx6qsabrelite.h and - undefine CONFIG_ENV_IS_IN_MMC - define CONFIG_ENV_IS_IN_SPI_FLASH The SPI driver can take as chip select the controller's chip selects as well as an external GPIO. The LSB byte has the value of the internal chip select, the highest (thought as 16-bit value) contains the GPIO number. The GPIO used on Sabre Lite is GP3:19 == 83. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* mx6q: mx6qsabrelite: Provide default serial flash bus and chip-selectEric Nelson2012-02-27-0/+2
| | | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* mx6q: mx6qsabrelite: Add ECSPI support to the Sabrelite platformEric Nelson2012-02-27-0/+9
| | | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* mx28evk: add SPI supportMatthias Fuchs2012-02-27-3/+41
| | | | | | | | | | | | | This patch adds SPI support for the MX28EVK. Support for an optionally installed SPI flash is also added. An example configuration for redundant envrionment from SPI flash is also added but disabled by default. This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx28evk: add USB supportMatthias Fuchs2012-02-27-0/+12
| | | | | | | This patch enables USB host support on the MX28EVK board. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx28evk: add RTC supportMatthias Fuchs2012-02-27-0/+8
| | | | | | | | This patch adds support for the MX28 internal RTC and enables u-boot's date command. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* microblaze: Enable TFTP put commandStephan Linz2012-02-23-0/+1
| | | | Signed-off-by: Stephan Linz <linz@li-pro.net>
* Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk2012-02-13-0/+314
|\ | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-blackfin: Blackfin: pata_bfin: fix printf warning Blackfin: bfin_nand: mark local func static linkage.h: move from blackfin to common includes Blackfin: br4: new board port Blackfin: add in/out le32 variants post: add blackfin to the post_time_ms list Blackfin: bf537-stamp: drop board reset workaround Blackfin: pr1: new board port
| * Blackfin: br4: new board portDimitar Penev2012-02-12-0/+157
| | | | | | | | | | | | | | | | This adds support for the BR4 Appliance. It is a quad channel ISDN BRI board based on Blackfin BF537 CPU. Signed-off-by: Dimitar Penev <dpn@switchfin.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * Blackfin: pr1: new board portDimitar Penev2012-02-12-0/+157
| | | | | | | | | | | | | | | | This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX. This board is Blackfin BF537 based. The schematics are not fully opened. Signed-off-by: Dimitar Penev <dpn@switchfin.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | arm, davinci: Add support for the Calimain board from OMICRON electronicsChristian Riesch2012-02-12-0/+363
| | | | | | | | | | | | | | | | | | This patch adds support for the Calimain board from OMICRON electronics GmbH. The board features a Texas Instruments AM1808 SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and CS3. Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
* | Changes to move hawkboard to the new spl infrastructureSughosh Ganu2012-02-12-7/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch moves hawkboard to the new spl infrastructure from the older nand_spl one. Removed the hawkboard_nand_config build option -- The spl code now gets compiled with hawkboard_config, after building the main u-boot image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard to reflect the same. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Tom Rini <trini@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at>
generated by cgit v1.1 at 2024-11-14 16:23:34 +0000