summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* ppc/85xx: Simplify the top makefile for 36-bit config for P2020DSKumar Gala2009-10-03-0/+4
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ppc/85xx: Simplify the top makefile for 36-bit config for MPC8572DSKumar Gala2009-10-03-0/+4
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ppc/85xx: simplify the top makefile for 36-bit config for mpc8536dsMingkai Hu2009-10-03-1/+1
| | | | | Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ppc/85xx: Fix LCRR_CLKDIV definesKumar Gala2009-10-03-3/+3
| | | | | | | | | | | | | | | | | | | | | For some reason the CLKDIV field varies between SoC in how it interprets the bit values. All 83xx and early (e500v1) PQ3 devices support: clk/2: CLKDIV = 2 clk/4: CLKDIV = 4 clk/8: CLKDIV = 8 Newer PQ3 (e500v2) and MPC86xx support: clk/4: CLKDIV = 2 clk/8: CLKDIV = 4 clk/16: CLKDIV = 8 Ensure that the MPC86xx and MPC85xx still get the same behavior and make the defines reflect their logical view (not the value of the field). Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Peter Tyser <ptyser@xes-inc.com>
* galaxy5200: enable version environment variableEric Millbrandt2009-10-03-0/+2
| | | | | | | | | | | Add version environment variable configuration to the galaxy5200 board header file. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Edited commit message. Signed-off-by: Wolfgang Denk <wd@denx.de>
* digsy_mtc: Add TCR register value for RTC (DS1339)Werner Pfister2009-10-03-0/+1
| | | | | Signed-off-by: Werner Pfister <werner.pfister@intercontrol.de> Signed-off-by: Detlev Zundel <dzu@denx.de>
* ppc4xx: Make DDR2 timing for intip more robustDirk Eibach2009-10-03-10/+10
| | | | | | | | DDR2 timing for intip was on the edge for some of the available chips for this board. Now it is verfied to work with all of them. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc: Clean up calling of phy_reset() during initPeter Tyser2009-10-03-0/+17
| | | | | | | Remove board-specific #ifdefs for calling phy_reset() during initializtion Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* ppc: Clean up calling of misc_init_r() during initPeter Tyser2009-10-03-2/+15
| | | | | | | | Remove board-specific #ifdefs for calling misc_init_r() during initializtion Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Acked-by: Heiko Schocher <hs@denx.de>
* Remove deprecated 'autoscr' command/variablesPeter Tyser2009-10-03-17/+17
| | | | | | | | | | | | | | | The more standard 'source' command provides identical functionality to the autoscr command. Environment variable names/values on the MVBC_P, MVBML7, kmeter1, mgcoge, and km8xx boards are updated to no longer refernce 'autoscr'. The 'autoscript' and 'autoscript_uname' environment variables are also removed. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Heiko Schocher <hs@denx.de>
* FDT: remove obsolete OF_CPU and OF_SOC macros.Marcel Ziswiler2009-10-03-11/+0
| | | | | | Signed-off-by: Marcel Ziswiler <marcel.ziswiler@noser.com> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Heiko Schocher <hs@denx.de>
* TI: DaVinci DM365: Minor config cleanupSandeep Paulraj2009-10-03-2/+0
| | | | | | | | | | The DM365 config was using the 'CONFIG_CMD_SAVEENV' flag. This is already included when we include the config_cmd_default.h header file. So this flag is removed. Also another flag to enable NAND functions was being enabled incorrectly. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* TI DaVinci: DM355: Config Cleanup and UpdateSandeep Paulraj2009-10-03-9/+12
| | | | | | | | | | | | | | | | | | This patch does the following 1) Enables the NAND driver which is now available. 2) Enables the 'CONFIG_MTD_DEVICE' as without this the compilation will fail 3) We now have a safe place to store environment and defines an offset where this can be stored. This offset value is such that it is after the location where U-Boot is flashed using TI flash utilities. 4) Enables Bootdelay 5) Increases malloc() arena size. Manufacturers are coming out with NAND with large blocks sizes of upto 1 MiB. It has been noticed that as the block size of the NAND used is increased, if this particular value is not increased, the NAND driver will output out of memory errors. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ppc4xx: Enable commands for FDT enabled Linux booting on AMCC AcadiaStefan Roese2009-10-03-1/+2
| | | | | | | | Acadia still used the "old" arch/ppc bootm commands for booting Linux images without FDT. This patch now enables these fdt-aware boot commands for Acadia as well. Signed-off-by: Stefan Roese <sr@denx.de>
* NAND boot: change NAND loader's relocate SP to CONFIG paramMingkai Hu2009-10-03-0/+2
| | | | | | | | | | So that we can set the NAND loader's relocate stack pointer to the value other than the relocate address + 0x10000. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ppc/85xx: Enable usb ehci support for p2020ds boardRoy Zang2009-10-03-0/+9
| | | | | Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc8260: remove Ethernet node fixup to use generic FDT code.Marcel Ziswiler2009-10-03-0/+2
| | | | | | | | Remove Ethernet node fixup from mgcoge and muas3001 boards and modify its configs for the common mpc8260 code to use generic Ethernet fixup. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@noser.com> Tested-by: Heiko Schocher <hs@denx.de>
* microblaze: Enable hush parserMichal Simek2009-10-03-1/+7
| | | | | | With Hush parser is possible to change command line in dtb Signed-off-by: Michal Simek <monstr@monstr.eu>
* microblaze: Remove AtmarkTechno Suzaku boardMichal Simek2009-10-03-110/+0
| | | | | | | Users should use microblaze-generic platform. This platform is longer not supported. Signed-off-by: Michal Simek <monstr@monstr.eu>
* net: Remove old Xilinx Emac driverMichal Simek2009-10-03-4/+1
| | | | Signed-off-by: Michal Simek <monstr@monstr.eu>
* microblaze: Short size of global data and fix malloc sizeMichal Simek2009-10-03-2/+2
| | | | | | | If is full malloc area global, data are rewrite because there was bad size of malloc area. Signed-off-by: Michal Simek <monstr@monstr.eu>
* ppc4xx: Rename compactcenter to intipDirk Eibach2009-10-03-4/+4
| | | | | Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Big cleanup of PPC4xx definesStefan Roese2009-10-03-4/+4
| | | | | | | | | | | | | | | | This patch cleans up multiple issues of the 4xx register (mostly DCR, SDR, CPR, etc) definitions: - Change lower case defines to upper case (plb4_acr -> PLB4_ACR) - Change the defines to better match the names from the user's manuals (e.g. cprpllc -> CPR0_PLLC) - Removal of some unused defines Please test this patch intensive on your PPC4xx platform. Even though I tried not to break anything and tested successfully on multiple 4xx AMCC platforms, testing on custom platforms is recommended. Signed-off-by: Stefan Roese <sr@denx.de>
* r7780mp: fix typo in Ethernet chip model number comment.Marcel Ziswiler2009-10-03-1/+1
| | | | Signed-off-by: Marcel Ziswiler <marcel.ziswiler@noser.com>
* ep8248: add support for device tree and secondary Ethernet interface.Marcel Ziswiler2009-10-03-30/+19
| | | | Signed-off-by: Marcel Ziswiler <marcel.ziswiler@noser.com>
* ppc4xx: Add CONFIG_PCI_4xx_PTM_OVERWRITE to some esd 4xx boardsMatthias Fuchs2009-10-03-0/+12
| | | | | Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* amcc-common.h: Use filenames from environment variables for update procedure.Detlev Zundel2009-10-03-3/+5
| | | | | | | | | | Using a separate "u-boot" environment variable allows to easily specify different filenames for the update procedure. This is also in line with many other board configurations defining an "update" script. Signed-off-by: Detlev Zundel <dzu@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* Reset i2c slave devices during init on mpc5xxx cpusEric Millbrandt2009-10-03-0/+1
| | | | | | | | | | | Reset any i2c devices that may have been interrupted during a system reset. Normally this would be accomplished by clocking the line until SCL and SDA are released and then sending a start condtiion (From an Atmel datasheet). There is no direct access to the i2c pins so instead create start commands through the i2c interface. Send a start command then delay for the SDA Hold time, repeat this by disabling/enabling the bus a total of 9 times. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
* galaxy5200: Add chip select region for an Epson S1D15313Eric Millbrandt2009-10-03-0/+5
| | | | Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
* Add PCI support to eNET boardGraeme Russ2009-10-03-7/+7
| | | | Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* Misc sc520 cdp fixupsGraeme Russ2009-10-03-22/+0
| | | | | | | Now that the PCI, SATA et al compile problems have been resolved, the cludge that was applied to avoid them can be removed Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* Fixup sc520_spunk boardGraeme Russ2009-10-03-0/+2
| | | | | | | | Primary intent is to resolve build errors for this board which has been neglected for a very long time. I do not have one of these boards, so I cannot test functionality Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* i386: Misc PCI fixupsGraeme Russ2009-10-03-0/+2
| | | | | | | | | | | | | | | | | | | | Change PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY (Originally done in commit ff4e66e93c1a, regressed by commit 6d7f610b09f8) Cast PCI_ROM_ADDRESS_MASK to u32 Wrap probe_pci_video() call inside #ifdef CONFIG_VIDEO Change call to pci_find_class() to pci_find_devices(). This is based on a patch submitted on 1st March 2007 (Patch that fixes the compilation errors for sc520_cdp board) by mushtaq_k This patch requires that PCI_VIDEO_VENDOR_ID and PCI_VIDEO_DEVICE_ID be specified in the board config file. Dummy values have been added for the SC520 CDP board to enable compilation, but since I do not have one of these, I do know what the values should be Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* Fix environment configuration for eNET boardGraeme Russ2009-10-03-6/+5
| | | | | | | | The current configuration of the Environment has the redundant copy of the environment in the Boot Flash - This was never the intent. The Environment should instead be in the first two sectors of the first Strata Flash Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* Blackfin: enable 64bit printf for nandMike Frysinger2009-10-03-0/+3
| | | | | | | | Since the NAND code now uses 64bit code, make sure we enable support for ADI Blackfin boards in printf to avoid the warning: nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output! Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: cm-bf537u: new board portHarald Krapfenbauer2009-10-03-0/+150
| | | | | | | | The CM-BF537U is similar to the CM-BF537E module, but enough to need its own board port. Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: enable more network commands for ADI dev boardsRobin Getz2009-10-03-0/+10
| | | | | | | | Add dns and ntp to default networking commands, and ask for more dhcp options to better configure the network environment. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf537-stamp: comment CF-Flash Card Support betterMichael Hennerich2009-10-03-5/+24
| | | | | Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: use +(filesize) to make sure we are only doing what is necessaryRobin Getz2009-10-03-2/+2
| | | | | Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* TI DaVinci: DM6446: Fix Compilation error in NAND modeSandeep Paulraj2009-09-15-0/+1
| | | | | | | | | | | | The Default mode that is built for the Davinci DVEVM happens to be the NOR mode. When we want to build for the NAND mode, we get a compilation error. This is overcome by defining the CONFIG_MTD_DEVICE flag in the NAND mode. The image built for NAND mode was successfully tested on the DaVinci DM6446 EVM. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* TI DaVinci: Remove references to SZ_xxSandeep Paulraj2009-09-15-19/+13
| | | | | | | | | | This patch removes the asm/sizes.h header file from being included in the DaVinci SOC configs. References to SZ_xx have been replaced by appropriate bit shifted values. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Acked-by: Wolfgang Denk <wd@denx.de>
* ARM: DaVinci: Adding Support for DaVinci DM365 EVMSandeep Paulraj2009-09-05-0/+182
| | | | | | | This patch adds support for the DM365 EVM. It has been tested on a DM365 EVM. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Add support for the DevKit8000 boardFrederik Kriewitz2009-09-05-0/+307
| | | | | | This patch adds support for the DevKit8000 board. Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
* Support for the Calao TNY-A9260/TNY-A9G20 boardsAlbin Tonnerre2009-09-01-0/+172
| | | | | | | | | | | | The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by Calao Systems <http://www.calao-systems.com>. Their components are very similar to the AT91SAM9260EK board, so their configuration is based on the configuration of this board. There are however some differences: different clocks, no LCD, no ethernet. They also can use SPI EEPROM to store the environment. Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Add support for the Calao SBC35-A9G20 boardAlbin Tonnerre2009-09-01-0/+194
| | | | | | | | | | | The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems <http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND flash, two USB host ports, and an USB device port. More informations can be found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936> Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
* imx27lite: add support for imx27lite board from LogicPDIlya Yanok2009-09-01-0/+252
| | | | | | | | | This patch adds support for i.MX27-LITEKIT development board from LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND flash, FEC ethernet controller integrated into i.MX27. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Acked-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'next' of ../nextWolfgang Denk2009-08-31-94/+1153
|\
| * 85xx: Added PCIe support for P1 P2 RDBPoonam Aggrwal2009-08-28-0/+6
| | | | | | | | | | | | | | Call fsl_pci_init_port() to initialize all the PCIe ports on the board. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Fix memory test range on MPC8536DSFelix Radensky2009-08-28-2/+2
| | | | | | | | | | | | | | | | | | | | With current values of CONFIG_SYS_MEMTEST_START and CONFIG_SYS_MEMTEST_END memory test hangs if run without arguments. Set them to sane values, so that all available 512MB of RAM excluding exception vectors at the bottom and u-boot code and stack at the top can be tested. Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Removed BEDBUG support on P1_P2_RDBKumar Gala2009-08-28-1/+0
| | | | | | | | | | | | To match all other 85xx platforms we are removing BEDBUG support. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-10-19 09:39:03 +0000