summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* Changes in uboot DDR configuration for MPC8313eRDBPoonam Aggrwal2008-01-16-16/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These changes were identified by HighSmith Bill ,Mazzyar and Joseph for DDR configuration in u-boot code. Some are related to performance, some affect stability and some correct few basic errors in the current configuration. The changes have been tested and found to give better memory latency figures on MPC8313eRDB.LMBench figures prove it. The changes are: - CS0_CONFIG[ AP_n_EN] is changed from 1 to 0 (this may improve performance for application with many read or write to open pages). - CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to 001 (activating all the CS when only one is used may cause unwanted noise on the system) - TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on Tras=45ns) - TIMING_CFG_1[REFREC] changed from 21 clks to 18clks. - TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to comply with the 3 ODT clk requirements) - TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4. - TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks. - DDR_SDRAM_MODE[AL]changed from 0 to 1. - DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks. - DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510. - DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500. The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git The last commit on this tree was 6775c68683a53c7abc778774641aac6f833a2cbf Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com> Cc: Bill HighSmith <Bill.Highsmith@freescale.com> Cc: Razzaz Mazyar <MRazzaz@freescale.com> Cc: Josep P J <PJ.Joseph@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Enable the isdram command on the MPC8360EMDS boardJerry Van Baren2008-01-16-0/+1
| | | | | | | | | The isdram command prints out decoded information the "serial presence detect" (SPD) chip on the SDRAM SIMMs. This can be very helpful when debugging memory configuration problems. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Add the support for MPC8315ERDB boardDave Liu2008-01-16-0/+547
| | | | | | | | | | | | | The features list: - Boot from NOR Flash - DDR2 266MHz hardcoded configuration - Local bus NOR Flash R/W operation - I2C, UART, MII and RTC - eTSEC0/1 support - PCI host Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Remove cache config from MPC8360ERDK.hDave Liu2008-01-16-9/+0
| | | | | | | | | | | The MPC8360ERDK board support patch is added before the commit 2c5b48fc205c3e2752910da8f39209ed075929e5 so, miss clean up it. The patch clean up the miss cache config. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* LWMON5: enable hush shell as command line parserWolfgang Denk2008-01-16-0/+6
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ADS5121: disable watchdog; enable image timestampsWolfgang Denk2008-01-15-6/+6
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* TK885D: fixes for bigger flash sector sizes on new modules;Wolfgang Denk2008-01-15-2/+5
| | | | | | | adjust default environment; disable SCC ethernet (not used on this board). Signed-off-by: Wolfgang Denk <wd@denx.de>
* ADS5121: Fix typo in ads5121.c, adjust default environmentWolfgang Denk2008-01-13-28/+32
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* MPC8360ERDK: fix incorrect initialization of CFG_I2C_NOPROBESWolfgang Denk2008-01-13-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ads5121: Added support for FDT.Grzegorz Bernacki2008-01-12-0/+8
| | | | Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
* Coding Style cleanup; update CHANGELOG.Wolfgang Denk2008-01-12-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* MUNICes: Set the right CFG_DEFAULT_MBAR value.Heiko Schocher2008-01-12-0/+2
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* added the config File for the MUNICes board.Heiko Schocher2008-01-12-0/+214
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* Fix defaultconfig for the mgcoge board.Heiko Schocher2008-01-12-1/+1
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* Added support for the mgcoge board from keymile.Heiko Schocher2008-01-12-0/+317
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* Added support for the mgsuvd board from keymile.Heiko Schocher2008-01-12-0/+325
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* Remove superfluous preprocessor conditionals from LM73 driverLarry Johnson2008-01-12-1/+0
| | | | | | | | (1) Remove unused symbol "CFG_EEPROM_PAGE_WRITE_ENABLE". (2) Use conditional Makefile.o. Signed-off-by: Larry Johnson <lrj@acm.org>
* Add support for the TK885D baseboard from TELE-DATAGuennadi Liakhovetski2008-01-12-0/+513
| | | | | | | | | The TK885D board uses a TQM885D module from TQ, this port adds an own configuration file and adds a last_stage_init() method to configure the two PHYs, depending on the phy_auto_nego environment variable. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
* Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk2008-01-12-13/+20
|\
| * ppc4xx: Rework Lime support for lwmon5Anatolij Gustschin2008-01-11-0/+16
| | | | | | | | | | | | Rework Lime support for lwmon5 using new video driver Signed-off-by: Anatolij Gustschin <agust@denx.de>
| * ppc4xx: Update PMC440 config fileMatthias Fuchs2008-01-11-13/+3
| | | | | | | | Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
| * ppc4xx: Make Sequoia boot vxWorksNiklaus Giger2008-01-10-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | vxWorks expects in TLB 0 a entry for the Machine Check interrupt TLB 1 a entry for the RAM TLB 2 a entry for the EBC TLB 3 a entry for the boot flash After changing the baudrate to 9600 I had no problems to boot the vxWorks image as distributed by WindRiver (Revision 2.0/1 from June 18, 2007) Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-mpc83xxWolfgang Denk2008-01-12-84/+559
|\ \
| * | mpc83xx: Make the code more readableDave Liu2008-01-10-6/+13
| | | | | | | | | | | | | | | | | | | | | Format the code, make it more readable Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: Reduce the latency of DDRDave Liu2008-01-10-5/+5
| | | | | | | | | | | | | | | | | | | | | Reduce the AL from 2 to 1 clock to improve the performance. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: Remove cache config from config.hDave Liu2008-01-10-73/+0
| | | | | | | | | | | | | | | | | | | | | clean up the cache config from configs.h of board Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: add support for the MPC8360E-RDKAnton Vorontsov2008-01-10-0/+538
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is MPC8360E based board with: - 256MB fixed SDRAM; - 8MB Intel Strata NOR flash; - StMICRO 64MiB NAND flash; - two 10/100/1000 ethernet ports connected via Broadcom BCM5481 PHYs; - two 10/100 ethernet ports connected via National DP83848 PHYs; - one PCI and one miniPCI slots; - four serial ports (two NS16550-compatible, two UCCs); - four USB ports working through MPC8360E "FHCI" USB controller; - Fujitsu MB86277 graphics controller; - Analog to Digital Converter/Touchscreen controller, AD7843 connected to SPI. Features not supported in this patch are: - StMICRO 64MiB NAND flash (patch sent); - MINT framebuffer initialization (patch is pending); - Fetching production information from the EEPROM via I2C; - FHCI USB; - Two slow UCCs used as RS-485 UARTs. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: add missing CONFIG_HAS_ETH0 definesKim Phillips2008-01-10-0/+3
| |/ | | | | | | | | | | | | | | | | the new libfdt code only updates eth0 if CONFIG_HAS_ETH0 is defined; add the define to the missing board configs. Thanks to Emilian Medve for finding this. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | Merge commit 'wd/master'Jon Loeliger2008-01-10-121/+1035
|\ \ | |/
| * Remove cache config from ATUM8548 and sbc8548 configsAndy Fleming2008-01-09-14/+0
| | | | | | | | | | | | | | These boards weren't updated by Kumar's config patch because they weren't in the tree, yet. Signed-off-by: Andy Fleming <afleming@freescale.com>
| * 85xx: Remove cache config from configs.hKumar Gala2008-01-09-112/+0
| | | | | | | | | | | | | | | | | | Either use the standard defines in asm/cache.h or grab the information at runtime from the L1CFG SPR. Also, minor cleanup in cache.h to make the code a bit more readable. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * mpc85xx: Add support for ATUM8548 (updated)robert lazarski2008-01-09-0/+465
| | | | | | | | | | | | Add support for Instituto Atlantico's ATUM8548 board Signed-off-by: robert lazarski <robertlazarski@gmail.com>
| * mpc85xx: Add support for SBC8548 (updated)Joe Hamman2008-01-09-0/+576
| | | | | | | | | | | | Add support for Wind River's SBC8548 reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
| * trivial: fix consequences of a bad mergeGuennadi Liakhovetski2008-01-09-1/+0
| | | | | | | | | | | | Fix what looks like a merge artifact. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
| * fix comments with new drivers organizationMarcel Ziswiler2008-01-09-8/+8
| | | | | | | | Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
* | 86xx: Remove cache config from configs.hJon Loeliger2008-01-09-7/+0
| | | | | | | | | | | | Just use the standard defines in asm/cache.h. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* | Convert MPC8610HPCD to use libfdt.Jon Loeliger2008-01-09-17/+14
|/ | | | | | | | | Assumes the presence of the aliases node in the DTS to locate the pci and serial nodes for fixups. Use consistent fdtaddr and fdtfile in environment variables. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* Improve configuration of FPGA subsystemMatthias Fuchs2008-01-09-3/+9
| | | | | | | | | | | | | This patch removes the FPGA subsystem configuration through the CONFIG_FPGA bitmask configuration option. See README for the new options: CONFIG_FPGA, CONFIG_FPGA_<vendor>, CONFIG_FPGA_<family> Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
* Coding Style cleanup, update CHANGELOGWolfgang Denk2008-01-09-9/+9
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://www.denx.de/git/u-boot-armWolfgang Denk2008-01-09-0/+238
|\
| * Merge with git://www.denx.de/git/u-boot.gitPeter Pearse2008-01-07-1300/+3449
| |\
| * | Remove warnings re CONFIG_EXTRA_ENV_SETTINGSPeter Pearse2007-11-15-9/+9
| | | | | | | | | | | | Remove warnings re onenand_read() & write()
| * | Merge with git://www.denx.de/git/u-boot.gitPeter Pearse2007-11-15-1/+1
| |\ \
| * | | Add apollon board supportPeter Pearse2007-11-09-0/+238
| | | | | | | | | | | | | | | | Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* | | | Merge branch 'master' of git://www.denx.de/git/u-boot-mpc83xxWolfgang Denk2008-01-09-53/+624
|\ \ \ \
| * | | | mpc83xx: convert to using do_fixup_*()Kim Phillips2008-01-08-45/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | convert to using simpler mpc85xx style fdt update code; streamline by eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm the old school FLAT_TREE code from 83xx (since the sbc8349 was just converted over to using libfdt). Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | | | sbc8349: enable libfdt by default on WRS SBC8349 board.Paul Gortmaker2008-01-08-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make libfdt the default for the WRS SBC8349 board. Parallel of commit 35cc4e4823668e8745854899cfaedd4489beb0ef done for the other 83xx based boards. Also fix a typo in CONFIG_PCI. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
| * | | | mpc83xx: Remove CONFIG options related to OF that we dont use (on 837x)Kim Phillips2008-01-08-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | continuation of commit 37395fa2b0d9d617f28d44ca11592260ef16105a to 837x Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | | | Remove CONFIG options related to OF that we dont useKumar Gala2008-01-08-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MPC8360E MDS config defined: CONFIG_OF_HAS_BD_T CONFIG_OF_HAS_UBOOT_ENV Which we don't use or ever needed. This seems like copy-paste feature creep. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | | | mpc83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions for 837xKim Phillips2008-01-08-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for 837x. This change guarantees that the environment will be located on the first flash sector after the U-Boot image. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
generated by cgit v1.1 at 2024-12-16 09:49:33 +0000