summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* TQM8xx: use the CFI flash driver on all TQM8xx boardsMartin Krause2007-12-27-64/+116
| | | | Signed-off-by: Martin Krause <martin.krause@tqs.de>
* TQM885D: adjust for doubled flash sector size + some minor fixesMartin Krause2007-12-27-7/+13
| | | | Signed-off-by: Martin Krause <martin.krause@tqs.de>
* TQM885D: Exchanged SDRAM timing by a more relaxed timing.Jens Gehrlein2007-12-27-1/+1
| | | | | | | | CAS-Latency=2, Write Recovery Time tWR=2 The max. supported bus frequency is 66 MHz. Therefore, changed threshold to switch from 1:1 mode to 2:1 from 80 MHz to 66 MHz. Signed-off-by: Martin Krause <martin.krause@tqs.de>
* TQM885D: use calculated cpuclk instead of measuring itMartin Krause2007-12-27-7/+0
| | | | | | | | | On the TQM885D the measurement of cpuclk with the PIT reference timer ist not necessary. Since all module variants use the same external 10 MHz oscillator, the cpuclk only depends on the PLL configuration - which is readable by software. Signed-off-by: Martin Krause <martin.krause@tqs.de>
* TQM885D: fix SDRAM refreshJens Gehrlein2007-12-27-16/+20
| | | | | | | | | | | | At 133 MHz the current SDRAM refresh rate is too fast (measured 4 * 1.17 us). CFG_MAMR_PTA changes from 39 to 128. This result in a refresh rate of 4 * 7.8 us at the default clock 66 MHz. At 133 MHz the value will be then 4 * 3.8 us. This is a compromise until a new method is found to adjust the refresh rate. Signed-off-by: Martin Krause <martin.krause@tqs.de>
* TQM860M: Support for 10col SDRAMs, max. 128 MiBJens Gehrlein2007-12-27-2/+5
| | | | Signed-off-by: Martin Krause <martin.krause@tqs.de>
* Merge branch 'master' of git://www.denx.de/git/u-boot-shWolfgang Denk2007-12-27-0/+245
|\ | | | | | | | | | | | | | | Conflicts: MAINTAINERS Signed-off-by: Wolfgang Denk <wd@denx.de>
| * Merge git://www.denx.de/git/u-bootNobuhiro Iwamatsu2007-12-07-1/+1
| |\
| * \ Merge git://www.denx.de/git/u-bootNobuhiro Iwamatsu2007-12-07-2/+0
| |\ \ | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/Makefile
| * \ \ Merge git://www.denx.de/git/u-bootNobuhiro Iwamatsu2007-11-29-448/+455
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/Makefile
| * | | | sh: Add support Renesas sh7722 processor and Hitachi MS7722SE01 boardNobuhiro Iwamatsu2007-09-23-0/+137
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * | | | sh: Update MS7750SE01 platformNobuhiro Iwamatsu2007-09-23-23/+56
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * | | | Merge git://www.denx.de/git/u-bootNobuhiro Iwamatsu2007-09-23-6977/+18140
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: CREDITS
| * | | | | sh: MS7750SE support.Nobuhiro Iwamatsu2007-05-13-0/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Hitachi MS7750SE. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | | | | | AVR32: Add support for the ATSTK1004 boardHaavard Skinnemoen2007-12-17-0/+185
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU, which is a derivative of AT32AP7000. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
* | | | | | AVR32: Add support for the ATSTK1003 boardHaavard Skinnemoen2007-12-17-0/+184
| |_|_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU, which is a derivative of AT32AP7000. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
* | | | | ADS5121 Board: fix compile problem.Wolfgang Denk2007-12-06-1/+1
| |_|_|/ |/| | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | | [BUILD] conditionally compile common/cmd_*.c in common/MakefileGrant Likely2007-11-20-2/+0
| |_|/ |/| | | | | | | | | | | | | | | | | Modify common/Makefile to conditionally compile the cmd_*.c files based on the board config. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | | Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDSHaiying Wang2007-11-19-5/+5
| | | | | | | | | | | | | | | | | | CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
* | | Fix the i2c frequency and default address in rsdproto boardLuotao Fu2007-11-17-2/+2
| | | | | | | | | | | | | | | | | | | | | rsdproto board support has wrong I2C frequency and wrong return value handling. Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk2007-11-17-2/+2
|\ \ \
| * \ \ Merge branch 'master' of git://www.denx.de/git/u-bootStefan Roese2007-11-13-267/+220
| |\ \ \
| * \ \ \ Merge git://www.denx.de/git/u-bootStefan Roese2007-10-27-78/+87
| |\ \ \ \
| * | | | | ppc4xx: lwmon5: Some further GPIO config changesStefan Roese2007-10-23-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
* | | | | | Unify pixis_reset altbank across board familiesJason Jin2007-11-17-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Basically, refactor the CFG_PIXIS_VBOOT_MASK values into the separate board config files. Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
* | | | | | [UC101] SRAM now with 2 MB working.Heiko Schocher2007-11-13-1/+1
| |_|/ / / |/| | | | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* | | | | Cleanup coding style; update CHANGELOGWolfgang Denk2007-11-03-1/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | | | Fix USB support issue for MPC8641HPCN board.Zhang Wei2007-11-03-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The configuration file has already enabled USB, but it missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB on MPC8641HPCN can not work because of the wrong USB register endian. And add the USB command to U-Boot commands list. Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
* | | | | Use config_cmd_default.h instead of config_cmd_all.hJean-Christophe PLAGNIOL-VILLARD2007-11-03-229/+160
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | | | | changes for IDS8247 board supportSergej Stepanov2007-11-03-10/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To get the IDS8247 board working following are done: - FCC2 is deactivated - FCC1 is activated - I2C is activated - CFI driver is activated - Adapted for use with LIBFDT Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de> --
* | | | | Merge branch 'master' of /home/wd/git/u-boot/workWolfgang Denk2007-11-02-28/+30
|\ \ \ \ \ | |_|/ / / |/| | | |
| * | | | Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2007-11-02-27/+26
| |\ \ \ \
| | * | | | ATSTK1002: Remove default ethernet addressesHaavard Skinnemoen2007-11-01-8/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wolfgang is right: It's not a good idea to set up default initial ethernet addresses for a board, even though they belong to the local range. This will change the failure mode from "IT manager screams at you for using duplicate ethernet addresses" to a nice error message explaining that the ethernet address hasn't been set properly. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
| | * | | | Merge branch 'master' of git://www.denx.de/git/u-boot-coldfireWolfgang Denk2007-11-01-19/+23
| | |\ \ \ \
| | | * | | | ColdFire 54455: Fix correct boot location for atmel and intelTsiChungLiew2007-10-25-16/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
| | | * | | | ColdFire 5329: Assign correct SDRAM size and fix cacheTsiChungLiew2007-10-25-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
| | | * | | | ColdFire 5253: Assign correct SDRAM sizeTsiChungLiew2007-10-25-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
| | | * | | | ColdFire 5282: Fix external flash boot and return dramsizeTsiChungLiew2007-10-25-1/+1
| | | |/ / / | | | | | | | | | | | | | | | | | | Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
| | * | | | Merge branch 'master' of git://www.denx.de/git/u-boot-tq-groupWolfgang Denk2007-11-01-1/+1
| | |\ \ \ \
| | | * | | | TQM5200: fix spurious characters on second serial interfaceMartin Krause2007-10-24-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause <martin.krause@tqs.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
| | | * | | | Merge branch 'u-boot' of /home/mkr/git/u-boot-tq-group into bugfixMartin Krause2007-10-23-0/+4
| | | |\ \ \ \ | | | | |/ / /
| * | | | | | Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2007-11-01-1/+4
| |\ \ \ \ \ \ | | |/ / / / /
| | * | | | | Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xxWolfgang Denk2007-11-01-1/+4
| | |\ \ \ \ \
| | | * | | | | Improve handling of PCI interrupt device tree fixup on MPC85xx CDSKumar Gala2007-10-19-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the MPC85xx CDS we have two issues: 1. The device tree fixup code did not check to see if the property we are trying to update is actually found. Its possible that it would update random memory starting at 0. 2. Newer Linux kernel's have moved the location of the PCI nodes to be sibilings of the soc node and not children. The explicit PATH to the PCI node would not be found for these device trees. Add the ability to handle both paths. In the future we shouldn't handle such fixups by explicit path. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| | | * | | | | Set OF_STDOUT_PATH to match the default console on MPC8568 MDSKumar Gala2007-10-19-1/+1
| | | | |/ / / | | | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the MPC8568 MDS we use ttyS0, UART0, etc. as the standard configured console. Make it so we match that config what we tell Linux as the early STDOUT console. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | | | | | TQM5200: increase kernel_addr_r and fdt_addr_r (hinted by Wolfgang Denk).Bartlomiej Sieka2007-10-25-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
* | | | | | | Merge branch 'motionpro_ng' of /home/tur/git/u-bootWolfgang Denk2007-10-24-14/+15
|\ \ \ \ \ \ \ | |/ / / / / / |/| | | | | |
| * | | | | | Motion-PRO: Update configuration to accomodate next generation board.Bartlomiej Sieka2007-10-23-14/+15
| | |/ / / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | New board has faster oscillator and a different Flash chip. This affects: - CFG_MPC5XXX_CLKIN - SDRAM timings - Flash CS configuration (timings) - Flash sector size, and thus MTD partition layout - malloc() arena size (due to bigger Flash sectors) - smaller memory test range (due to bigger malloc() arena) This patch also enables more extensive memory testing via "mtest". Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
* | | | | | TQM5200: fix spurious characters on second serial interfaceMartin Krause2007-10-24-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause <martin.krause@tqs.de>
* | | | | | delta: Fix OHCI_REGS_BASE undeclared and wait_ms implicit declarationJean-Christophe PLAGNIOL-VILLARD2007-10-24-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
generated by cgit v1.1 at 2024-12-25 02:52:54 +0000