summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* omap3: mvblx: pass FPGA version to the kernelMichael Jones2013-02-18-0/+1
| | | | | | Extract FPGA version from the .rbf and pass this info to the kernel. Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
* omap3: mvblx: select fpgafilename according to orientationMichael Jones2013-02-18-3/+3
| | | | | | | | Rather than load the FPGA file from the FAT partition, look at entry in system EEPROM to decide which file to retrieve directly from the EXT3 partition. Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
* omap3: mvblx: change console to ttyO0 and make silent by default.Howard Gray2013-02-18-5/+13
| | | | | | | | Also, change bootdelay to 0 but allow pressing 'S' to stop at U-Boot prompt. Signed-off-by: Michael Jones <michael.jones@matrix-vision.de> Signed-off-by: Howard Gray <howard.gray@matrix-vision.de> Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
* OMAP3: igep00x0: Add new IGEP COM PROTON.Enric Balletbo i Serra2013-02-18-1/+5
| | | | | | | The IGEP COM PROTON is a new ultra compact module design with an on-board ethernet controller. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
* OMAP3: igep00x0: add missing include mach-types.hEnric Balletbo i Serra2013-02-18-0/+1
| | | | | | | | | | | | | | | | | | | | | Current '#if' directives (used in igep00x0.h config file) comparing MACH_TYPE values in igep00x0.h doesn't work as expected. The comparision between CONFIG_MACH_TYPE and MACH_TYPE_IGEP0020 is always true independent of the IGEP machine configured. For example, following directive if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) define something endif Is always evaluated true although we configure u-boot for MACH_TYPE_IGEP0030. The build doesn't shows any error so looks that both defines had always the same value. Including the mach-types.h file sets properly the value of MACH_TYPE_IGEPxxxx. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
* am335x_evm: enable support for booting via USBIlya Yanok2013-02-18-0/+14
| | | | | | | | | | | | | | | This adds necessary config options and a new build target, am335x_evm_usbspl, to enable usb booting and fixes board_eth_init() function to take into account that we may have USB ether support in SPL now. This uses the same MAC for both cpsw and USB, in order to match ROM behavior. The usbspl build target does not contain UART SPL, CPSW SPL or extra environment settings, so that we may fit within our binary size constraint. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com> Signed-off-by: Tom Rini <trini@ti.com>
* da8xx: ea20: Add the configuration define for the exact SoC variantTomas Novotny2013-02-18-0/+1
| | | | | | | Signed-off-by: Tomas Novotny <tomas@novotny.cz> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* x86: Rename CONFIG_NO_X86_RESET_VECTOR to CONFIG_X86_RESET_VECTORSimon Glass2013-02-14-1/+0
| | | | | | | Invert the polarity of this option to simplify the Makefile logic. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Gabe Black <gabeblack@chromium.org>
* x86: Remove eNET boardsSimon Glass2013-02-14-619/+0
| | | | | | | These are no longer used and should be removed. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Graeme Russ <graeme.russ@gmail.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-02-12-184/+1279
|\
| * Tegra114: Add/enable Dalmore build (T114 reference board)Tom Warren2013-02-11-0/+129
| | | | | | | | | | | | | | This build is stripped down. It boots to the command prompt. GPIO is the only peripheral supported. Others TBD. Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: cardhu: config: enable SPIAllen Martin2013-02-11-0/+11
| | | | | | | | | | | | | | | | Turn on SPI in cardhu config file Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: don't hard-code LCD into default TEGRA_DEVICE_SETTINGSStephen Warren2013-02-11-2/+9
| | | | | | | | | | | | | | | | | | Only add "lcd" into TEGRA_DEVICE_SETTINGS if CONFIG_VIDEO_TEGRA. Otherwise, "lcd" is meaningless. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * AM335X: Set fdt_high for AM335X devices to enable booting with Device Treehvaibhav@ti.com2013-02-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | For AM335X boards, such as the EVM and Bone Linux kernel fails to locate the device tree blob on boot. The reason being is that u-boot is copying the DT blob to the upper part of RAM when booting the kernel and the kernel is unable to access the blob. By setting the fdt_high variable to 0xffffffff (to prevent the copy) the kernel is able to locate the DT blob and boot. This patch is tested on BeagleBone platform. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Tom Rini <trini@ti.com>
| * pcm051: Add support for Phytec phyCORE-AM335xLars Poeschel2013-02-07-0/+301
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The board is named pcm051 and has this hardware: SOC: TI AM3359 DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB ETH 1: LAN8710AI SPI-Flash: W25Q64BVSSIG RTC: RV-4162-C7 I2C-EEPROM: CAT32WC32 NAND: MT29F4G08_VFPGA63 PMIC: TPS65910A3 LCD Supported: UART 1 MMC/SD ETH 1 USB I2C SPI Not yet supported: NAND RTC LCD Signed-off-by: Lars Poeschel <poeschel@lemonage.de> [trini: Add #define CONFIG_PHY_ADDR 0 to config] Signed-off-by: Tom Rini <trini@ti.com>
| * omap4: allow the use of a plain text env file instead boot scriptsJavier Martinez Canillas2013-02-07-3/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For production systems it is better to use script images since they are protected by checksums and carry valuable information like name and timestamp. Also, you can't validate the content passed to env import. But for development, it is easier to use the env import command and plain text files instead of script-images. Since both OMAP4 supported boards (Panda and TI SDP4430) are used primarily for development, this patch allows U-Boot to load env var from a text file in case that an boot.scr script-image is not present. The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence will be started. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Nishanth Menon <nm@ti.com>
| * OMAP3: igep00x0: add boot status GPIO LEDJavier Martinez Canillas2013-02-07-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds an GPIO LED boot status for IGEP boards. The GPIO LED used is the red LED0 while the Linux kernel uses the green LED0 as the boot status. By using different GPIO LEDs, the user can know in which step of the boot process the board currently is. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * OMAP3: use a single board file for IGEP devicesJavier Martinez Canillas2013-02-07-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Even when the IGEPv2 board and the IGEP Computer-on-Module are different from a form factor point of view, they are very similar in the fact that share many components and how they are wired. So, it is possible (and better) to have a single board file for both devices and just use the CONFIG_MACH_TYPE to make a differentiation between each board when needed. This change avoids code duplication by removing 298 lines of code and makes future maintenance easier. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-02-02-5/+426
| |\
| | * mx23evk: Add initial board supportOtavio Salvador2013-01-28-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following features are supported: * 128 MB DDR1 SDRAM * DUART * SD/MMC Card Socket Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
| | * mx23_olinuxino: Add default environmentOtavio Salvador2013-01-28-7/+70
| | | | | | | | | | | | | | | | | | This adds a default environment with support for MMC booting. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
| | * mxs: mmc: mx23_olinuxino: Add MMC supportMarek Vasut2013-01-28-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the MMC attached to SSP1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
| | * net: fec_mxc: delete CONFIG_FEC_MXC_MULTITroy Kisky2013-01-28-3/+0
| | | | | | | | | | | | | | | | | | | | | It is more logical to test for CONFIG_FEC_MXC_PHYADDR to determine whether to define the function fecmxc_initialize. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| | * mx6qsabre_common: Let mmc partition be board specificFabio Estevam2013-01-28-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 49ea0ff5 (49ea0ff5) introduced CONFIG_SYS_MMC_ENV_PART into mx6qsabresd.h to store the mmc partition, but in order for it to have effect we should place it into 'mmcpart' variable. Also add CONFIG_SYS_MMC_ENV_PART into mx6qsabreauto.h. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| | * mx6qsabreauto: enable USB host interfaceKnut Wohlrab2013-01-28-0/+11
| | | | | | | | | | | | | | | | | | The USB host interface is routed to plug USB1/J30 on the mother board. Signed-off-by: Knut Wohlrab <knut.wohlrab@de.bosch.com>
| | * mxs: Add MX23 olinuxino board supportMarek Vasut2013-01-21-0/+135
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for MX23-based Olinuxino board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| | * mxs: Linux uses ttyAMA0 as DUARTMarek Vasut2013-01-21-1/+1
| | | | | | | | | | | | | | | | | | | | | Replace use of ttyAM0 with ttyAMA0 as default serial console. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
| * | Tegra30: I2C: Enable I2C driver on CardhuTom Warren2013-01-16-0/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | Tested all 5 'buses', i2c probe enumerates device addresses on all but dev 4 (I2C4) [no devices on that bus on my Cardhu]. Note that this uses the extant tegra_i2c.c driver w/o modification. Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | Tegra30: Add/enable Cardhu build (T30 reference board)Tom Warren2013-01-16-173/+301
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This build is stripped down. It boots to the command prompt. GPIO is the only peripheral supported. Others TBD. include/configs/tegra-common.h now holds common config options for Tegra SoCs. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
| * | tegra: remove custom TEGRA_DEVICE_SETTINGS for board filesMarc Dietrich2013-01-16-18/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TEGRA_DEVICE_SETTINGS lives now in tegra-common-post.h. This removes custom TEGRA_DEVICE_SETTINGS for all tegra boards providing video output, except seaboard, which was fixed by Stephen already. Cc: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: enable LCD on PAZ00Marc Dietrich2013-01-16-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | This adds LCD panel descriptions to the device tree of PAZ00 and enables LCD support in the configuration. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: Enable LCD on TECThierry Reding2013-01-16-1/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | The TEC ships with a 7" LCD panel that provides a resolution of 800x480 pixels. Add a corresponding panel description to the device tree and enable LCD support in the configuration. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | tegra: Enable LCD on Medcom-WideThierry Reding2013-01-16-0/+14
| |/ | | | | | | | | | | | | | | | | The Medcom-Wide has a 15" LCD panel with a resolution of 1366x768 pixels. Add a corresponding panel description to the device tree and enable LCD support in the configuration. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini2013-02-04-4/+0
|\ \
| * | microblaze: Remove FSL support from generic boardMichal Simek2013-02-04-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | This code was targetting one specific Microblaze platform configuration which is obsolete and fsl bus isn't used in this way. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | configs:Remove unused macro CONFIG_DISCOVER_PHYAshok2013-02-04-2/+0
|/ / | | | | | | | | | | | | Remove unused macro CONFIG_DISCOVER_PHY from configs. Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
* | corenet: Disable video on P2020DSAndy Fleming2013-01-30-1/+1
| | | | | | | | | | | | | | | | The P2020DS build had grown too large, and video support isn't enabled in almost any other Freescale board. Disabling it allows us to keep building, and provides options for reenabling it later. Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/85xx: Add BSC9132QDS supportPrabhakar Kushwaha2013-01-30-0/+667
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSC9132QDS is a Freescale reference design board for BSC9132 SoC. BSC9132 SOC is an integrated device that targets the evolving Microcell, Picocell, and Enterprise-Femto base station market subsegments. It combines Power Architecture e500v2 and DSP StarCore SC3850 core technologies with MAPLE-B2F baseband acceleration processing elements. BSC9132QDS Overview -------------------- 2Gbyte DDR3 (on board DDR), Dual Ranki 32Mbyte 16bit NOR flash 128Mbyte 2K page size NAND Flash 256 Kbit M24256 I2C EEPROM 128 Mbit SPI Flash memory SD slot USB-ULPI eTSEC1: Connected to SGMII PHY eTSEC2: Connected to SGMII PHY PCIe CPRI SerDes I2C RTC DUART interface: supports one UARTs up to 115200 bps for console display Apart from the above it also consists various peripherals to support DSP functionalities. This patch adds support for mainly Power side functionalities and peripherals Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/p2041: set RCW and PBI files for .pbl build or P2041RDBValentin Longchamp2013-01-30-0/+2
| | | | | | | | | | | | | | | | | | | | | | In order to be able to build a u-boot.pbl image, both the CONFIG_PBLPBI_CONFIG and CONFIG_PBLRCW_CONFIG variables have to be defined. This patch sets these two files for the P2041RDB board. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/b4860qds: Added Support for B4860QDSYork Sun2013-01-30-0/+820
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | B4860QDS is a high-performance computing evaluation, development and test platform supporting the B4860 QorIQ Power Architecture processor. B4860QDS Overview ------------------ - DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 4 GB of memory in two ranks of 2 GB. - DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank. - SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point 16x16 switch VSC3316 - SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point 8x8 switch VSC3308 - USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode. - B4860 UART port is available over USB-to-UART translator USB2SER or over RS232 flat cable. - A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA connector ports 0 and 2 for AMC mode. - The B4860 configuration may be loaded from nine bits coded reset configuration reset source. The RCW source is set by appropriate DIP-switches: - 16-bit NOR Flash / PROMJet - QIXIS 8-bit NOR Flash Emulator - 8-bit NAND Flash - 24-bit SPI Flash - Long address I2C EEPROM - Available debug interfaces are: - On-board eCWTAP controller with ETH and USB I/F - JTAG/COP 16-pin header for any external TAP controller - External JTAG source over AMC to support B2B configuration - 70-pin Aurora debug connector - QIXIS (FPGA) logic: - 2 KB internal memory space including - IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK, DDRCLK1, 2 and RTCCLK. - Two 8T49N222A SerDes ref clock devices support two SerDes port clocks - total four refclk, including CPRI clock scheme Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/mpc8544ds: Add USB controller support for MPC8544DSHongtao Jia2013-01-30-0/+12
| | | | | | | | | | | | | | | | | | USB controller in uboot is a required feature for MPC8544DS. Without this support there is no 'usb' command in uboot. Signed-off-by: Jia Hongtao <B38951@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/mpc8572ds: Enable bank interleaving to cs0+cs1 for dual-rank DIMMsHongtao Jia2013-01-30-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | The controller interleaving only takes the usable memory mapped to cs0. In the case of bank interleaving not enabled, only half of dual-rank DIMM will be used. For single-rank DIMM bank interleaving will be auto disabled. Signed-off-by: Jia Hongtao <B38951@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/t4240qds: Update IFC timing for NOR flashYork Sun2013-01-30-5/+5
| | | | | | | | | | | | | | | | Relax parameters to give address latching more time to setup. Tighten parameters to make it overall faster. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | boards/T4240qds:Fix IFC AMASK init as per FPGA register spacePrabhakar Kushwaha2013-01-30-1/+1
| | | | | | | | | | | | | | | | | | | | T4240QDS's QIXIS FPGA has 4k register space size and IFC controller's Address Mask Registers is initialised 64K size. So Fix the Address Mask Register initilisation as 4K Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini2013-01-29-35/+0
|\ \
| * | Remove unused CONFIG_SYS_I2C_BUS[_SELECT]Michael Jones2013-01-29-35/+0
| |/ | | | | | | | | | | | | | | "CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere outside of config files. Signed-off-by: Michael Jones <michael.jones@matrix-vision.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | Merge remote-tracking branch 'mpc83xx/next'Kim Phillips2013-01-16-13/+30
|\ \ | |/ |/|
| * powerpc/mpc83xx: convert MPC8313ERDB to new-SPLScott Wood2012-12-19-13/+30
| | | | | | | | | | | | | | This converts MPC8313ERDB NAND boot to use the new SPL infrastructure. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-14-49/+192
|\ \
| * | mx6qsabresd: Fix booting the kernel from SDHC3Fabio Estevam2013-01-13-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit de7d02aeb (mx6qsabresd: add usdhc2 and usdhc4 support) SDHC3 device node is no longer 0, which breaks loading a uImage from SDHC3. Fix it by adapting the default environment to use CONFIG_SYS_MMC_ENV_DEV as the correct mmc node for loading the kernel from. While at it, go back to using SDHC3 as the default mmc, since we have Yocto images that generate an SD card containing U-boot,kernel and rootfs, so it is more convenient to keep using SDHC3 as it was originally. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit v1.1 at 2024-12-19 06:23:57 +0000