summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* tt01: add video supportHelmut Raiger2012-02-27-1/+28
| | | | | | | | The video setup for the Epson display is provided. Addtionally some extra info is displayed next to the Linux logo. Make get_cpu_rev() publicly available (added to sys_proto.h). Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* tt01: fix environment sizeHelmut Raiger2012-02-27-1/+1
| | | | | | size of environment must match erasable block size in the flash. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* i.mx6q: mx6qsabrelite: Update the network configurationTroy Kisky2012-02-27-0/+2
| | | | | | | | | | | | | | | | | | | Define CONFIG_PHY_MICREL, and minimize the tx clock delay. There is an issue with 1000 baseTx mode on early revs of the SabreLite boards. The center tap pin 9 of the mag RJ45 USB combo was connected to the 3.3 filtered supply. Letting this pin float solved the problem. Symptoms of the problem were packets with many extra zeroes tacked on the end, and random bit flips causing a high rate of CRC errors. 10/100 baseTx worked fine on all revs. To disable 1000 baseTx for these boards, simply define the environment variable disable_giga. ie. setenv disable_giga 1 Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
* integrator: update the Integrator/CP configLinus Walleij2012-02-27-34/+13
| | | | | | | | | | | | | | | | | | | The Integrator/CP config file was very outdated and gives a non functional U-Boot. So: - Set the CONFIG_ARCH_CINTEGRATOR arch flag correctly - Add proper core module configuration options - Skip cluttered command lista and just include <config_cmd_default.h> - Kill off #if 0 network section and insert some example configuration that simply just boots from the network using TFTP if available. - Delete flash control registers that have no business in this config file. These are already moved down to board/armltd/integrator/integrator-sc.h Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* integrator: rewrite the AP PCI driverLinus Walleij2012-02-27-142/+6
| | | | | | | | | | | | | | | | | | | | | | | | | The PCI support for the Integrator AP has apparently never been finished and I strongly suspect that it has never worked, so let's fix it. This is a list of the more or less un-splittable changes done in this driver rewrite: - Replace the register definitions stashed into the config file (!) with a copy if the register file from the Linux kernels arch/arm/include/asm/hardware/pci_v3.h - Delete the unreadable gigantic macros that perform the config accesses and replace them with copyedited code from Linux arch/arm/mach-integrator/pci_v3.c - Rewrite the rest of the setup code to use the v3_[read|write][lwb]() accessors. - Enable PCI by default in the AP board configuration. - Fix checkpatch warnings and make code more conformant. Tested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* mcx: Enable command line editingDetlev Zundel2012-02-27-0/+2
| | | | | Signed-off-by: Detlev Zundel <dzu@denx.de> CC: Stefano Babic <sbabic@denx.de>
* dm6467Tevm: Use a common configuration file for davinci_dm6467evm and ↵prabhakar.csengg@gmail.com2012-02-27-168/+0
| | | | | | | | | | | | | | | | | | | | davinci_dm6467Tevm In commit 2d575e46859dd9127a9cec731ace77523e6ea2ab a separate header file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h. The substantial difference between the davinci_dm6467evm and the davinci_dm6467Tevm configuration is a single bit in the hardware revision that is passed to the Linux kernel and davinci_dm6467evm has REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a REFCLK_FREQ = 33000000. This patch removes include/configs/davinci_dm6467Tevm.h. Instead the include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined in boards.cfg. Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com> Cc: Tom Rini <trini@ti.com>
* OMAP3: Remove unused CONFIG_SYS_NAND_ECCSTEPS/TOTALThomas Weber2012-02-27-14/+0
| | | | Signed-off-by: Thomas Weber <weber@corscience.de>
* Tricorder: Switch env to generic mmc driverThomas Weber2012-02-27-3/+4
| | | | | | | | Because the tricorder uses the CONFIG_OMAP_HSMMC the initialization command is mmc rescan and not mmc init. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tom Rini <trini@ti.com>
* mx6q: mx6qsabrelite: Conditionally define macros for environment in serial flashEric Nelson2012-02-27-3/+15
| | | | | | | | | | | | | | | | | | | | | | The default settings store the persistent environment on SD card and not serial flash (SPI NOR). To use SPI NOR to save the environment instead of SD card, edit include/configs/mx6qsabrelite.h and - undefine CONFIG_ENV_IS_IN_MMC - define CONFIG_ENV_IS_IN_SPI_FLASH The SPI driver can take as chip select the controller's chip selects as well as an external GPIO. The LSB byte has the value of the internal chip select, the highest (thought as 16-bit value) contains the GPIO number. The GPIO used on Sabre Lite is GP3:19 == 83. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* mx6q: mx6qsabrelite: Provide default serial flash bus and chip-selectEric Nelson2012-02-27-0/+2
| | | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* mx6q: mx6qsabrelite: Add ECSPI support to the Sabrelite platformEric Nelson2012-02-27-0/+9
| | | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* mx28evk: add SPI supportMatthias Fuchs2012-02-27-3/+41
| | | | | | | | | | | | | This patch adds SPI support for the MX28EVK. Support for an optionally installed SPI flash is also added. An example configuration for redundant envrionment from SPI flash is also added but disabled by default. This patch has been tested on a MX28EVK Rev. D with an installed SST25VF032B 32Mbit SPI flash. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx28evk: add USB supportMatthias Fuchs2012-02-27-0/+12
| | | | | | | This patch enables USB host support on the MX28EVK board. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx28evk: add RTC supportMatthias Fuchs2012-02-27-0/+8
| | | | | | | | This patch adds support for the MX28 internal RTC and enables u-boot's date command. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* microblaze: Enable TFTP put commandStephan Linz2012-02-23-0/+1
| | | | Signed-off-by: Stephan Linz <linz@li-pro.net>
* Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk2012-02-13-0/+314
|\ | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-blackfin: Blackfin: pata_bfin: fix printf warning Blackfin: bfin_nand: mark local func static linkage.h: move from blackfin to common includes Blackfin: br4: new board port Blackfin: add in/out le32 variants post: add blackfin to the post_time_ms list Blackfin: bf537-stamp: drop board reset workaround Blackfin: pr1: new board port
| * Blackfin: br4: new board portDimitar Penev2012-02-12-0/+157
| | | | | | | | | | | | | | | | This adds support for the BR4 Appliance. It is a quad channel ISDN BRI board based on Blackfin BF537 CPU. Signed-off-by: Dimitar Penev <dpn@switchfin.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * Blackfin: pr1: new board portDimitar Penev2012-02-12-0/+157
| | | | | | | | | | | | | | | | This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX. This board is Blackfin BF537 based. The schematics are not fully opened. Signed-off-by: Dimitar Penev <dpn@switchfin.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | arm, davinci: Add support for the Calimain board from OMICRON electronicsChristian Riesch2012-02-12-0/+363
| | | | | | | | | | | | | | | | | | This patch adds support for the Calimain board from OMICRON electronics GmbH. The board features a Texas Instruments AM1808 SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and CS3. Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
* | Changes to move hawkboard to the new spl infrastructureSughosh Ganu2012-02-12-7/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch moves hawkboard to the new spl infrastructure from the older nand_spl one. Removed the hawkboard_nand_config build option -- The spl code now gets compiled with hawkboard_config, after building the main u-boot image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard to reflect the same. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Tom Rini <trini@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at>
* | arm, arm926ejs: Add option CONFIG_SYS_EXCEPTION_VECTORS_HIGHChristian Riesch2012-02-12-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The V bit of the c1 register of CP15 should not be cleared on DA850 SoCs since they have no valid memory at 0x00000000. This patch introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH that allows setting the correct value for the V bit. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Reported-by: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Heiko Schocher <hs@denx.de>
* | arm, arm926ejs: Do cpu critical inits only for boards that require itChristian Riesch2012-02-12-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch reverts commit ca4b55800ed74207c35271bf7335a092d4955416 "arm, arm926ejs: always do cpu critical inits" since it impacts all arm926ejs based configurations and caused problems, e.g., with the hawkboard. Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines from the board configurations that need low level initialization. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
* | davinci: add support for printing clock frequencyHadli, Manjunath2012-02-12-0/+61
| | | | | | | | | | | | | | | | | | add support for printing various clock frequency info found in SOC such as ARM core frequency, DSP core frequency and DDR frequency as part of bdinfo command. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Cc: Tom Rini <trini@ti.com>
* | davinci: remove macro CONFIG_DISPLAY_CPUINFOHadli, Manjunath2012-02-12-10/+0
| | | | | | | | | | | | | | | | | | | | remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer required. This is because clock info will be printed as part 'bdinfo' command and also remove support print_cpuinfo() as it will no longer be called. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Cc: Tom Rini <trini@ti.com>
* | mcx: support for HTKW mcx boardIlya Yanok2012-02-12-0/+378
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the HTKW mcx AM3517-based board. Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both NAND and MMC SPLs are supported. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> Cc: Detlev Zundel <dzu@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | ARM: omap3: Added Teejet mt_ventouxStefano Babic2012-02-12-2/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The mt_ventoux board is a custom board using the Technexion TAM3517 module. The patch fixes also the mtdparts variable in the TAM3517 common configuration file. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Igor Grinberg <grinberg@compulab.co.il> CC: Tom Rini <tom.rini@gmail.com> Cc: Detlev Zundel <dzu@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | OMAP3: TAM3517: update ehci interfaceStefano Babic2012-02-12-0/+2
| | | | | | | | | | | | | | | | Changed the EHCI interface using the ulpi framework. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | OMAP4: ehci-omap: enable ehci-omap for panda boardsGovindraj.R2012-02-12-1/+22
| | | | | | | | | | | | | | | | For panda initialise the mux pins for ehci usage and enable ehci in omap4_panda config file. Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Tested-by: Stefano Babic <sbabic@denx.de>
* | ehci-omap: driver for EHCI host on OMAP3Ilya Yanok2012-02-12-0/+4
| | | | | | | | | | | | | | Taken from Beagle code. Tested on mcx board (AM3517-based). Signed-off-by: Ilya Yanok <yanok@emcraft.com> Tested-by: Stefano Babic <sbabic@denx.de>
* | usb: ulpi: Add omap-ulpi-view port supportGovindraj.R2012-02-12-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on discussion from this thread [1]. Adding omap-view port that helps us in using the generic ulpi framework for any ulpi phy ops using the INSNREG05_ULPI viewport reg available on omap platform. Currently ehci ports are available on omap3/4 platforms so enable the same for beagle and panda, patch is tested on the same boards. Thanks to Igor Grinberg <grinberg@compulab.co.il> for reviewing the omap-ehci patches and suggesting this approach. [1]: http://www.mail-archive.com/u-boot@lists.denx.de/msg76076.html Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* | SMDK5250: Add ethernet supportChander Kashyap2012-02-12-2/+9
| | | | | | | | | | | | | | | | | | This patch enable support for SMC911X based ethernet device. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | EXYNOS: SMDK5250: Add MMC SPL supportChander Kashyap2012-02-12-0/+7
| | | | | | | | | | | | | | This patch adds support for MMC SPL booting. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | EXYNOS: Add SMDK5250 board supportChander Kashyap2012-02-12-0/+190
| | | | | | | | | | | | | | SMDK5250 board is based on Samsungs EXYNOS5250 SoC. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | Exynos: Clock.c: Use CONFIG_SYS_CLK_FREQ macroChander Kashyap2012-02-12-0/+2
| | | | | | | | | | | | | | | | | | CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (Exynos4) architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ to make it generic for exynos architecture. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | ORIGEN: remove duplicated MACH_TYPE defineMinkyu Kang2012-02-12-2/+0
| | | | | | | | | | | | | | | | Since MACH_TYPE_ORIGEN is updated on mach-types, remove the MACH_TYPE_ORIGEN on config file. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
* | ARMV7: Exynos4: Add support for TRATS boardHeungJun, Kim2012-02-12-0/+216
| | | | | | | | | | | | | | | | This patch adds support for Samsung TRATS board Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | arm/km: speed up i2c access for keymile boardsHolger Brunck2012-02-12-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | We don't need 3us delay for our i2c bus. Decrease it to 1us. It would also be possible to use 100ns in the future, but currently kirkwood has no ndelay implementation. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* | kirkwood: add support for D-Link DNS-325Stefan2012-02-12-0/+188
| | | | | | | | | | | | | | | | This patch adds support for D-Link DNS-325 ShareCenter NAS. Signed-off-by: Stefan Herbrechtsmeier <stefan@code.herbrechtsmeier.net> Cc: prafulla@marvell.com Cc: albert.u.boot@aribaud.net
* | edminiv2: add USB host supportAlbert ARIBAUD2012-02-12-0/+14
| | | | | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | edminiv2: add hush parser, cmdline editing and long helpAlbert ARIBAUD2012-02-12-0/+10
| | | | | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | ARM: activate DISPLAY_CPUINFO for VCMA9 + SMDK2410 boardDavid Müller (ELSOFT AG)2012-02-12-4/+2
| | | | | | | | | | Signed-off-by: David Mueller <d.mueller@elsoft.ch> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* | tt01: add MMC supportHelmut Raiger2012-02-12-0/+12
| | | | | | | | | | | | | | | | board_mmc_init() initializes the pins of SDHC1 and turns on V_MMC1 of the PMIC. Config adds support for EXT2 and FAT. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* | configs: Remove CONFIG_NET_MULTI from board filesFabio Estevam2012-02-12-30/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_NET_MULTI is not used anymore, so remove it from board files. Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Kumar Gala <kumar.gala@freescale.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Heiko Schocher <hs@denx.de>
* | i.mx6q: mx6qsabrelite: Add the ethernet function supportJason Liu2012-02-12-2/+11
| | | | | | | | | | | | | | Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de>
* | i.mx6q: configs: Add fdt_high and initrd_high variablesDirk Behme2012-02-12-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To be able to load the device tree and initrd correctly, set the fdt_high and initrd_high environment variables. Using 0xffffffff implies that the device tree and the initrd are initially copied to working addresses. This will avoid an additional copy. Loading the device tree to 0x30000000 and the initrd to 0x3c000000 should work for both boards, the ARM2 and SabreLite. Example (SabreLite): fatload mmc 0:2 0x10000000 uImage fatload mmc 0:2 0x3c000000 uInitrd fatload mmc 0:2 0x30000000 board.dtb bootm 0x10000000 0x3c000000 0x30000000 Note: This requires that the kernel has CONFIG_HIGHMEM enabled. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
* | sdhc_boot: Introduce CONFIG_FSL_FIXED_MMC_LOCATION optionFabio Estevam2012-02-12-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 97039ab98 (env_mmc: Allow board code to override the environment address) mmc_get_env_addr is a weak-aliased function in common/env_mmc.c The mmc_get_env_addr implementation that exists at board/freescale/common/sdhc_boot.c is meant to be used only for PowerPC boards, but currently it is being used for all platforms that have CONFIG_ENV_IS_IN_MMC defined. Introduce CONFIG_FSL_FIXED_MMC_LOCATION so that the boards that need to use the mmc_get_env_addr version from board/freescale/common/sdhc_boot.c could activate this config option on their board file. This fixes the retrieval of CONFIG_ENV_OFFSET on non-PowerPC boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Stefano Babic <sbabic@denx.de>
* | arm, davinci: cam_enc_4xx board updatesHeiko Schocher2012-02-12-25/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - CONFIG_SYS_MMC_ENV_DEV, needed if environment on mmc - wait for 1 second timer in board_late_init() only, if timer is running. - add UBI/UBIFS support - add FIT images support - menu support - U-Boot max size now 0xa0000 - SPL now Block 0 page 0 - new MTD partitioning 0x00000000 SPL 0x00020000 UBL-Header 0x00040000 UBL-Header 0x00060000 UBL-Header 0x00080000 UBoot (0xa0000(U-Boot length) + 0x60000(3 spare blocks)) 0x00180000 ENV- Variablen (1) 0x001a0000 ENV- Variablen (2) 0x001c0000 ENV- Variablen (reserved for Bad Block) 0x001e0000 ENV- Variablen (reserved for Bad Block) 0x00200000 UBI-Device UBI Volumes: „default“: contain environment-default values „rootfs1“: UBIFS root-fs (1); contain linux kernel image „rootfs2“: UBIFS root-fs (2); contain linux kernel image „data-ro“: UBIFS data (read only) „data-rw“: UBIFS data (read/write) - new environment variables: - app_reset (this is only passed per cmdline to linux) - dvn_app_vers string from ramdisk description contained in the FIT image - dvn_boot_vers string from ubootimage description contained in the FIT image - saveparms, restoreparms, restoretmpparms, savetmpparms helper for saving network parameter. - ubiargs set ubi kernel cmdlinargs for booting with a ubifs rootfs - ubi_ubi boot with reading kernel image from ubifs, and use a ubifs as rootfs Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Wolfgang Denk <wd@denx.de>
* | OMAP3: Add Corscience Tricorder boardThomas Weber2012-02-12-0/+320
| | | | | | | | | | | | | | | | | | Tricorder is a board which is very similar to the Devkit8000. It is designed as a base platform for further medical devices. www.corscience.de/en/medical-engineering/products/multiparameter/mp10-board.html Signed-off-by: Thomas Weber <weber@corscience.de>
* | am3517evm: remove rootfstype kernel parameter for MMC boot deviceYegor Yefremov2012-02-12-2/+1
| | | | | | | | | | | | | | it is not necessary to define rootfstype for mass storage devices. Kernel detects it automatically. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
generated by cgit v1.1 at 2024-12-21 05:42:06 +0000