| Commit message (Collapse) | Author | Age | Lines |
|
|
|
| |
Signed-off-by: Pieter Voorthuijsen <pv@prodrive.nl>
|
|
|
|
| |
Signed-off-by: Pieter Voorthuijsen <pv@prodrive.nl>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed. And CONFIG_ defines were added
to various board config files to make sure that happens.
The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.
Boards that are CDS specific were renamed with cds_ prefix.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When we go to 36-bit physical addresses we need to keep the concept of
the physical CCSRBAR address seperate from the virtual one.
For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so
- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|/
|
|
|
|
|
|
| |
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
common/cmd_bootm.c
cpu/mpc8xx/cpu.c
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
|
| |
| |
| |
| | |
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
With the original value of 1/2 clock cycle delay, the system ran relatively
stable except when we run benchmarks that are intensive users of memory.
When I run samba connected disk with a HDBENCH test, the system locks-up
or reboots sporadically.
Signed-off by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.
Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| |
| |
| |
| |
| |
| |
| | |
At least on the "33MHz Pilot" board crystal is actually 33.3MHz.
This patch fixes "system time drifting" problem.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| |
| |
| | |
This is needed to update /choosen/linux,stdout-path properly.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| |
| |
| |
| | |
Plus modify environment to use it and remove bootfile env variable,
it is internal and CONFIG_BOOTFILE is used for these purposes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Current DDR setup easily causes memory corruption, this patch fixes it.
Also fix TIMING_CFG0_MRS_CYC definition.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| | |
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| |
| |
| | |
This is needed for BCM PHYs to work on this board.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| |
| |
| | |
This is primarily for the early console support.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| | |
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
| |
| |
| |
| |
| | |
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
| |
| |
| |
| |
| |
| |
| | |
There's no on-board RTC on the MPC8323ERDB, but there is an EEPROM.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
| |
| |
| |
| |
| |
| |
| | |
Use available shift/mask macros to define DDR configuration.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
These defines embedded the u-boot env variables and/or the bd_t structure
in the fdt blob. The conclusion of discussion on the u-boot email list
was that embedding these in the fdt blob is not useful: there are better
ways of passing the data (in fact, the fdt blob itself replaces the
bd_t struct).
The only board that enables these is the stxxtc and they don't appear
to be used by linux.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
| |
| |
| |
| | |
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
|
| |
| |
| |
| |
| |
| |
| |
| | |
- insert partition for dtb blob to TQM5200B MTD layout
- set env variables dependent on the configured board
(TQM5200 or TQM5200B)
Signed-off-by: Martin Krause <martin.krause@tqs.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
lwmon5 board: the storage for the log-buffer itself is OCM(on-chip memory), the log-buffer header is moved to six GPT registers (PPC440EPX_GPT0_COMP1, ..., PPC440EPX_GPT0_COMP5).
To enable this, alternative, configuration the U-Boot board configuration
file for lwmon5 includes the definitions of alternative addresses for header
(CONFIG_ALT_LH_ADDR) and buffer (CONFIG_ALT_LB_ADDR).
The Linux shall be configured with the CONFIG_ALT_LB_LOCATION option set,
and has the BOARD_ALT_LH_ADDR and BOARD_ALT_LB_ADDR constants defined in the
lwmon5 board-specific header (arch/ppc/platforms/4xx/lwmon5.h).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
|
| |
| |
| |
| |
| | |
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* External Watchdog test;
* dsPIC tests;
* FPGA test;
* GDC test;
* Sysmon tests.
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
|
|\ \ |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The parallel flash on the BF537-STAMP is CFI compliant, so there is no need
for the board specific driver at all. Just use the common CFI driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
| |/
| |
| |
| |
| |
| |
| |
| | |
Stop tying things to the processor that should be tied to other defines and
change BFIN_CPU to CONFIG_BFIN_CPU so that it can be used in the build
system to select the -mcpu option.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Conflicts:
drivers/rtc/Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |/
| |
| |
| |
| |
| | |
Fix configuration for mgcoge board
Signed-off-by: Heiko Schocher <hs@denx.de>
|
| |
| |
| |
| | |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |
| |
| |
| |
| |
| |
| | |
This patch adds USB OHCI support to the Canyonlands board port. It also
enables EXT2 support.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
| |
| |
| |
| |
| |
| | |
This patch adds support for the AMCC Canyonlands 460EX evaluation
board.
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
| |
| |
| | |
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|/
|
|
|
|
|
| |
Cleanup: Remove custom flash driver for 8 bit boot-eprom and replace it with
the FLASH_CFI_LEGACY et al. config options.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| | |
the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|\ \ |
|
| |/
| |
| |
| | |
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |
| |
| |
| |
| |
| | |
initialize the UPIOx controller.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|/
|
|
|
|
|
| |
add support for the config Flash.
initialize the UPIOx controller.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
|
|
|
|
|
|
|
| |
1. Make the CSB bus pipeline depth as 4, and enable
the repeat mode;
2. Raise the eTSEC emergency priority;
3. Use the highest IP blocks clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|