summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
...
* | | | arm: mvebu: theadorable: Add PEX-switch detection and reset codeStefan Roese2016-04-12-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sometimes the PCIe link for the PEX-switch will not come-up. In this case, the board is not in a usable state. This patch makes sure that in this case a soft-reset is issued. If this soft-reset does not result in the PEX-switch being detected after some soft-reset cycles, an I2C message is sent to the uC to issue a complete power-cycle of the board. Signed-off-by: Stefan Roese <sr@denx.de>
* | | | arm: mvebu: theadorable: Enable 2nd I2C controllerStefan Roese2016-04-12-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables the 2nd I2C controller on the Armada XP theadorable board. Signed-off-by: Stefan Roese <sr@denx.de>
* | | | arm: mvebu: theadorable: Add bootcounter supportStefan Roese2016-04-12-0/+8
| |_|/ |/| | | | | | | | | | | | | | | | | | | | This patch adds bootcount support to the MVEBU theadorable board. Since no reset-safe registers seem to be available, it uses the last 4KiB of SDRAM for the bootcounter location. Signed-off-by: Stefan Roese <sr@denx.de>
* | | rpi: remove redundant board filesStephen Warren2016-04-11-251/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that rpi_*defconfig and Kconfig (rather than the config header file) provide the identity of the build, we don't need to separate config headers and board directories for each RPi variant. Set CONFIG_SYS_BOARD and CONFIG_SYS_CONFIG_NAME so that we can get rid of the duplication. This requires a tiny number of extra ifdefs in the config header. The only disadvantage of this approach is that the $board/$board_name environment variables aren't as descriptive as they used to be. This isn't really an issue because those only exist to allow scripts to create DTB filenames at runtime. However, the RPi board code already sets $fdtfile to something more accurate based on FW-reported board ID anyway. While at it, unify some Kconfig select options, and add a MAINTAINERS entry for bcm283x too. Partially-suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | ARM: add Raspberry Pi 3 64-bit configStephen Warren2016-04-11-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On all Pis so far, the VC FW provides a short stub to set up the ARM CPU before entering the kernel (a/k/a U-Boot for us). This feature is not currently supported by the VC FW when booting in 64-bit mode. However, this feature will likely appear in the near future, and this U-Boot port assumes that such a feature is in place. Without that feature, or a temporary workaround described below, U-Boot will not boot. Once the VC FW does provide the ARM stub, u-boot.bin built for rpi_3 can be used drectly as kernel7.img, in the same way as any other RPi port. The following config.txt is required: # Fix mini UART input frequency, and setup/enable up the UART. # Without this option, U-Boot will not boot, even if you don't care # about the serial console. This option will always be required for # all RPi3 use-cases, unless the PL011 UART is used, which is not # yet supported by rpi_3* builds of U-Boot. enable_uart=1 # Boot in AArch64 (64-bit) mode. # It is possible that a future VC FW will remove the need for this # option, instead auto-setting 32-/64-bit mode based on the "kernel" # filename present on the SD card. arm_control=0x200 Prior to the VC FW providing the ARM boot stub, you can use the following steps to build an equivalent stub into the U-Boot binary: git clone https://github.com/swarren/rpi-3-aarch64-demo.git \ ../rpi-3-aarch64-demo (cd ../rpi-3-aarch64-demo && ./build.sh) Build U-Boot for rpi_3 in the usual way cat ../rpi-3-aarch64-demo/armstub64.bin u-boot.bin > u-boot.bin.stubbed Use u-boot.bin.stubbed as kernel7.img on the Pi SD card. In this case, the following additional entries are required in config.txt: # Tell the FW to load the kernel image at address 0, the reset vector. kernel_old=1 Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini2016-04-10-8/+6
|\ \ \
| * | | arm: socfpga: Drop space after 'loadaddr=' in extra envMarek Vasut2016-04-10-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is an incorrect space after loadaddr= in the extra environment, so drop it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Chin Liang See <clsee@altera.com>
| * | | arm: socfpga: migration of CONFIG_SPI_FLASH_BARDenis Bakhvalov2016-04-10-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_SPI_FLASH_BAR was deleted from socfpga_common.h and placed in socfpga_*_defconfig because it is Kconfig symbol. Signed-off-by: Denis Bakhvalov <dendibakh@gmail.com> Reported-by: Denis Bakhvalov <dendibakh@gmail.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini2016-04-10-0/+7
|\ \ \ \
| * | | | board: pic32mzda: enable USB-host, USB-storage support.Purna Chandra Mandal2016-04-10-0/+7
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | Enable MUSB host and USB storage support for Microchip PIC32MZ[DA] Starter Kit. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2016-04-08-22/+22
|\ \ \ \ | |/ / / |/| | |
| * | | powerpc: Replace CONFIG_SYS_INIT_RAM_END with CONFIG_SYS_INIT_RAM_SIZEYork Sun2016-04-08-21/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_SYS_INIT_RAM_SIZE may be used out of the board header file. Some boards use CONFIG_SYS_INIT_RAM_END for the same purpose. To unify the macros, use CONFIG_SYS_INIT_RAM_SIZE for all. Signed-off-by: York Sun <york.sun@nxp.com> CC: Mario Six <mario.six@gdsys.cc> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
| * | | powerpc: t1040qds: Use generic ethsw commandsCodrin Ciubotariu2016-04-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commands for the VSC9953 l2 switch from T1040 became generic in patch https://patchwork.ozlabs.org/patch/499748/ and the define was renamed. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | | armv8: LS2080A: Consolidate LS2080A and LS2085AYork Sun2016-04-06-20/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS2080A is the primary SoC, and LS2085A is a personality with AIOP and DPAA DDR. The RDB and QDS boards support both personality. By detecting the SVR at runtime, a single image per board can support both SoCs. It gives users flexibility to swtich SoC without the need to reprogram the board. Signed-off-by: York Sun <york.sun@nxp.com> CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
* | | | armv8: ls1043a: load Fman ucode from SD/MMC under SD bootQianyu Gong2016-04-06-1/+9
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | | armv8: ls1043a: load Fman ucode from NAND flash under NAND bootQianyu Gong2016-04-06-1/+5
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | | armv8/ls1043aqds: modify CONFIG_SYS_MAX_FLASH_BANKS to 1Wenbin Song2016-04-06-1/+1
|/ / / | | | | | | | | | | | | | | | | | | There is only one flash bank for ls1043aqds. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini2016-04-04-23/+44
|\ \ \
| * | | ARM64: zynqmp: Enable EFI partition supportMichal Simek2016-04-04-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Enable EFI partition support for ZynqMP. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM: zynq: Add uEnv.txt supportMichal Simek2016-04-04-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | preboot macro load the uEnv.txt from mmc 0 when bootmode is mmc. uenvcmd is executed after load of uEnv.txt if it is defined in the uEnv.txt env text file. The default importbootenv macro reads the uEnv.txt from mmc. Additional to this, usb_loadbootenv is added to support loading uEnv.txt from usb dev 0. Signed-off-by: Jason Wu <jason.wu.misc@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | block: Add support for Ceva sataMichal Simek2016-04-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Initial Ceva Sata init code. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
| * | | ARM64: zynqmp: Read RAM information from DTMichal Simek2016-04-04-8/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Read information about memory from DT. This patch simplify life with synchronization between DT and board files. dram_init() only needs maximum RAM size below 4GB that's why please sort banks in memory node. dram_init_banksize() copies memory setup to bi_dram[]. This will avoid reading information from DT twice. Memory test start/end were changed to DDR location to let memtest still compiled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: Move HUSH enabling from board file to defconfigMichal Simek2016-04-04-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | Simplify board config file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: zynqmp: Enable FAT write and EXT4 write for USB tooMichal Simek2016-04-04-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | Enabling writing files to FAT and EXT4 for USB. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: zynqmp: Decrease boot delaySoren Brinkmann2016-04-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Synchronize it with zynq platform. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | microblaze: Remove !OF_CONTROL code for timer and interruptMichal Simek2016-04-04-12/+0
| | | | | | | | | | | | | | | | | | | | | | | | OF_CONTROL is enabled by default that's why this is dead code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM: zynq: zybo: Enabling reading MAC address from EEPROMMichal Simek2016-04-04-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Zybo has on board I2C EEPROM which contains preprogrammed MAC address. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM: zynq: Enable option to overwrite default variablesMichal Simek2016-04-04-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | Enable overwriting variables out of main config file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | zynq-common: Enable phy driver for Xilinx PCS/PMA coreSiva Durga Prasad Paladugu2016-04-04-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support of Xilinx PCS/PMA core phy for Zynq Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | | arm: mvebu: Add basic support for Armada 375 eval board db-88f6720Stefan Roese2016-04-04-0/+120
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds basic support for the Marvell A375 eval board. Tested are the following interfaces: - I2C - SPI - SPI NOR - Ethernet (mvpp2), port 0 & 1 Currently the A375 SerDes and DDR3 init code is not intergrated. So the SPL U-Boot is not fully functional. Right now, this A375 mainline U-Boot can only be used by chainloading it via the original Marvell U-Boot. This can be done via this command: => tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000 Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* | | board: Add Qualcomm Dragonboard 410C supportMateusz Kulikowski2016-04-01-0/+150
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit add support for 96Boards Dragonboard410C. It is board based on APQ8016 Qualcomm SoC, complying with 96boards specification. Features (present out of the box): - 4x Cortex A53 (ARMv8) - 2x USB Host port - 1x USB Device port - 4x LEDs - 1x HDMI connector - 1x uSD connector - 3x buttons (Power, Vol+, Vol-/Reset) - WIFI, Bluetooth with integrated antenna - 8GiB eMMC U-Boot boots chained with fastboot in 64-bit mode. For detailed build instructions see readme.txt in board directory. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Tested-by: Simon Glass <sjg@chromium.org>
* | | Migrate CONFIG_ULPI* to KconfigMateusz Kulikowski2016-04-01-10/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move CONFIG_USB_ULPI* from headers to defconfigs for boards that use it. Also - add CONFIG_USB where necesarry - all boards use it, but some are not defining it explicitly. Affected boards: colibri_t20, harmony, mcx, mt_ventoux, twister, zynq_(picozed, zc702, zc706, zed, zybo) Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | | board: ti: DRA7: Add DP83867 TI phy for rev cDan Murphy2016-04-01-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable the TI DP83867 Giga bit phy on the dra7 rev c board. The rx and tx internal delays are need for this board so the usage of RGMII_ID is required. Signed-off-by: Dan Murphy <dmurphy@ti.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | kc1: Add some sysboot and devicetree-related environment variablesPaul Kocialkowski2016-04-01-0/+2
| | | | | | | | | | | | | | | | | | This adds some environment variables for sysboot and devicetree. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* | | kc1: Include explicit serial baudrate on bootargsPaul Kocialkowski2016-04-01-1/+1
| | | | | | | | | | | | | | | | | | This makes the baudrate for the kernel command line explicit. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* | | sniper: Include explicit serial baudrate on bootargsPaul Kocialkowski2016-04-01-1/+1
| | | | | | | | | | | | | | | | | | This makes the baudrate for the kernel command line explicit. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* | | configs: ti_armv7_keystone2: make SYS_TEXT_BASE configurable at build timeVitaly Andrianov2016-04-01-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | U-boot for general purpose KS2 devices is loaded to the beginning of the internal memory (0x0c000000). Secure devices uses this memory and CONFIG_SYS_TEXT_BASE has to be different for those devices. This commit make this configurable at build time by giving CONFIG_SYS_TEXT_BASE as a command line definition to make command. Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
* | | rpi: BCM2837 and Raspberry Pi 3 32-bit supportStephen Warren2016-04-01-1/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with the CPU complex swapped out for a quad-core ARMv8. This can operate in 32- or 64-bit mode. 32-bit mode is the current default selected by the VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of U-Boot for the Raspberry Pi 3. >From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a change in usage of the SoC UARTs. On all previous Pis, the PL011 was the only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a UART to connect to the SoC. By default, the PL011 is used for this purpose since it has larger FIFOs than the other "mini" UART. However, this can be configured via the VideoCore firmware's config.txt file. This patch hard-codes use of the mini UART in the RPi 3 port. If your system uses the PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot port instead. A future change might determine which UART to use at run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed together. The mini UART has some limitations. One externally visible issue in the BCM2837 integration is that the UART divides the SoC's "core clock" to generate the baud rate. The core clock is typically variable, and under control of the VideoCore firmware for thermal management reasons. If the VC FW does modify the core clock rate, UART communication will be corrupted since the baud rate will vary from the expected value. This was not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To work around this, the VideoCore firmware can be told not to modify the SoC core clock. However, the only way this can happen and be thermally safe is to limit the core clock to a low/minimum frequency. This leaves performance on the table for use-cases that don't care about a UART console. Consequently, use of the mini UART console must be explicitly requested by entering the following line into config.txt: enable_uart=1 A recent version of the VC firmware is required to ensure that the mini UART is fully and correctly initialized by the VC FW; at least firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on core clock See: https://github.com/raspberrypi/firmware/issues/572". Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | ARM: bcm2835: move CONFIG_BCM283* to KconfigStephen Warren2016-04-01-2/+0
| | | | | | | | | | | | | | | Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2016-04-01-6/+46
|\ \ \
| * | | sunxi: Add support for Allwinner A64 SoCsSiarhei Siamashka2016-04-01-6/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Allwinner A64 SoC is used in the Pine64. This patch adds all bits necessary to compile U-Boot for it running in AArch64 mode. Unfortunately SPL is not ready yet due to legal problems, so we need to boot using the binary boot0 for now. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> [agraf: remove SPL code, move to AArch64] Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | | sunxi: usb_phy: Add support for A83T USB PHYsChen-Yu Tsai2016-03-31-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host, 1 for USB HSIC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | | ARM: uniphier: remove CONFIG_ARP_TIMEOUT defineMasahiro Yamada2016-04-01-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I no longer see the problem claimed in the comment block. Rather, the 0.5 msec timeout seems too short for some TFTP servers. Drop the CONFIG_ARM_TIMEOUT to fall back to the 5 sec timeout. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | | | ARM: uniphier: drop unneeded defines related to legacy serial driverMasahiro Yamada2016-04-01-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | These defined were used for pre-DM ns16550 serial driver. They are unneeded because UniPhier SoCs now use DM serial. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | | | ARM: uniphier: add sramupdate commandMasahiro Yamada2016-04-01-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | This command would be useful to update U-Boot images in SRAM. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | | | ARM: uniphier: make u-boot-with-spl.bin really availableMasahiro Yamada2016-04-01-0/+1
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit d085ecd61b99 ("ARM: uniphier: switch to raw U-Boot image") claimed that u-boot-with-spl.bin would be useful in its commit log, but it was not available because the commit missed to define CONFIG_SPL_MAX_SIZE. Without it, CONFIG_SPL_PAD_TO is not defined either (see include/config_fallbacks.h). So, the SPL image is not padded correctly. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2016-03-29-4/+24
|\ \ \
| * | | armv8/ls2080ardb: Enable VID supportRai Harninder2016-03-29-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enable VID support for ls2080ardb platform. It uses the common VID driver. Signed-off-by: Rai Harninder <harninder.rai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * | | armv8: ls2080rdb: ls2080qds: Add secure boot supportSaksham Jain2016-03-29-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sec_init has been called at the beginning to initialize SEC Block (CAAM) which is used by secure boot validation later for both ls2080a qds and rdb. 64-bit address in ESBC Header has been enabled. Secure boot defconfigs are created for boards (NOR boot). Signed-off-by: Saksham Jain <saksham.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * | | armv8/ls1043a: Update env settings for booting kernelQianyu Gong2016-03-24-4/+4
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit v1.1 at 2024-08-19 04:37:33 +0000